Coulisse ABC05 Motor for indoor blinds User Manual ABC 17 U indd
Coulisse B.V. Motor for indoor blinds ABC 17 U indd
Coulisse >
Contents
manual 2
1.
2.
1. 2.
indoor use only
ABC-17-U_R0_
1.1A
D1
L1
L2 D2
D4L3
D3
-
+
-
+
User manual
Middle motor
ABC-17
1. General information
1.1 General dimensions
The ABC-17 is a middle motor for the motorisation of the Absolute roman blind system of
Coulisse 25 mm venetian blinds and 20-25 mm pleated blinds. The motor can be operated
with the Coulisse remote control only. End positions and favourite positions can be programmed
with the remote control. The motor is silent, energy effi cient and equipped for the use of
batteries as well for the use of solar energy.
WARNING: Important safety instructions. Follow all instructions,
since incorrect installation can lead to severe injury.
Do not make repairs yourself. Do not attempt to open the device
or disassemble it. You run the risk of electric shock and voiding
the limited warranty. No user-serviceable parts are inside.
WARNING:
1.2 Performances
1.3 Compatibility
1.4 Connectors and buttons
Program button
12-24VDC -0.6A input
2. Programming and operating
2.1 First use
Step 1: Connect the motor to 12 - 24 VDC
(also possible by using ‘SingleSelect’, see manual remote control*)
*Manuals are also available on our website www.coulisse.nl
Step 2: Set the blind in program-mode by pushing the program button
Step 3: Pair the blind to a channel/remote
Choose channel
by pressing
the ChannelSelect button
Pair/unpair by pressing
the program button on
the backside of the remote
Press the up + down button to change
the rotation direction
Step 4: Draairichting veranderen
Set to program mode:
Shortly press
program button
Program mode:
Blind is
stepping...
1 sec
Action confi rmed:
blind stops stepping
for 3 seconds
Action confi rmed:
blind stops stepping
for 3 seconds
If you press down
and the blind goes up,
the rotation direction
of the blind
has to be switched.
Set the blind in program
mode and follow
this step.
We refer to the manual of the Coulisse Remote control to set the addtional blind settings.
2.4 Additional blind settings
5. Service & Support
4.2 Cleaning
Follow these general rules when cleaning the outside of the device and its components:
- Make sure the device is unplugged.
- Use a damp, soft, lint-free cloth. Avoid getting moisture in openings.
- Don’t use aerosol sprays, solvents, alcohol, or abrasives.
Do not make repairs yourself. Do not attempt to open the device or
disassemble it. You run the risk of electric shock and voiding the limited
warranty. No user-serviceable parts are inside.
WARNING:
Do not make repairs yourself. Do not attempt to open the device or
disassemble it. You run the risk of electric shock and voiding the limited
warranty. No user-serviceable parts are inside.
WARNING:
- Do not let children play with the blind and/or remote control.
- Only use powersupplies or batteries that comply with the specifi cations on the motor.
- In case of malfunction, unplug the device or remove the batteries and contact your dealer.
- Take care that the blind can move freely and is not blocked by objects.
- Take care that the powersupply cable is out of reach for children.
- Do not paint the device.
- Keep the device dry.
Online Resources
For the latest information and updated manuals go to www.coulisse.nl.
Obtaining Warranty Service
First follow the advice in this booklet and then go to your local dealer.
If the product appears to be damaged or does not function properly, go to your local dealer
for instructions on how to obtain warranty service.
3. Tips & Troubleshooting
Please check www.coulisse.nl for the latest tips and troubleshooting guide.
Disclaimer:
© Copyright Coulisse
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, by any means, electronic,
mechanical, photocopying, recording, digital or otherwise without the written permission of the publisher.
Although this manual has been composed with the most care, Coulisse B.V. does not accept any responsibility for damage due to mistakes and/or
faults in this manual.
Coulisse B.V. reserves the right to revise the manual and to revise and/or changes its content at any time, without obligation to notify any person
or entity of such revisions or changes.
The most recent version replaces older versions of this manual. The most recent version is available at ww.coulisse.nl or contact your Coulisse contact person.
We invite you to send remarks and comments about this manual to Coulisse at manuals@coulisse.nl.
Shortly press
program button
( <2 sec. )
Program mode:
Blind is
stepping...
- Reset to factory defaults & Erase all paired channels/remotes
Hold program button
for 10 sec. untill blind
stops stepping
2.2 Normal use
- Manual Control
Hold program button
for more than 2 sec.
Blind moves as
long as button
is pressed
(max. 15 sec.)
For moving in opposite
direction release button
and hold program button again
for more than 2 sec.
2.3 Resetten
Shortly press
program button
( <2 sec. )
Program mode:
Blind is
stepping...
- Reset to factory defaults
Hold program button
for 15 sec. untill blind
stops stepping
and steps once
1 sec 15 sec
Step 6: Exit the program-mode by pressing the program button again
Then set the lower endposition
Step 5: Set endpositions (the positions can also be set after fi rst installation)
Use the up and down
buttons to go to
the lower endposition
Set the position
by pressing
the center + up button
Action confi rmed:
blind stops stepping
for 3 seconds
Action confi rmed:
blind stops stepping
for 3 seconds
Exit program mode:
Shortly press
program button
1 sec 10 sec
>2 sec
Type Power
supply
Rated
Power
Max. lifting
weight
Max.
Torq - rpm
Operating
temp.
Max. channels
to pair
ABC-17 12-24VDC 0.6A-7W 4,5 kg 0.8Nm-28 rpm 5°-60° 32 channels
Type Roman blinds Venetian blind Pleated blind
ABC-17 35 mm 25 mm 20-25 mm
OR
Additional blind settings: Available
Switch rotation direction Yes
Favorite position Yes
BatteryMode/Solar Yes
4. Safety & Cleaning
Use the up and down
buttons to go to
the upper endposition
Set the position
by pressing
the center + down button
First set the upper endposition
Type L1 L2 L3 Ø D1 Ø D2 Ø D3 Ø D4
ABC-17 182 192 126 24 5 24 9
4.1 Safety
GB0
Program button
12-24VDC -0.6A input