Digi 50M1699 WLAN Module User Manual CC Wi i MX51 HRM

Download:
Mirror Download [FCC.gov]
Document ID	1406130
Application ID	2XDenfBrEVW8sYF5rOjaMA==
Document Description	User Manual Part2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	283.31kB (3541376 bits)
Date Submitted	2011-01-18 00:00:00
Date Available	2011-03-04 00:00:00
Creation Date	2011-01-18 12:07:21
Producing Software	Acrobat Distiller 9.2.0 (Windows)
Document Lastmod	2011-01-18 12:07:25
Document Title	CC Wi-i.MX51 HRM.book
Document Creator	FrameMaker 9.0
Document Author:	jlee2

ConnectCore f or i .M X 5 1
Two 2 x 10 pin headers, X15 and X17, are provided on the development board for connecting
two Digi camera application kits (optional) or customer specific hardware.
X15
connector for camera 1
X17
connector for camera 2
X15 Pinout
Pin
Signal
Pin
Signal
+2.775V
GND
CSI1_D12
CSI1_D13
CSI1_D14
CSI1_D15
CSI1_D16
CSI1_D17
CSI1_D18
10
CSI1_D19
11
CSI1_MCLK
12
CSI1_PIXCLK
13
CSI1_HSYNC/GPIO3_15
14
CSI1_VSYNC/GPIO3_14
15
GPIO1_2/I2C2_SCL
16
GPIO1_3/I2C2_SDA
17
CSI1_D10
18
CAMRESET1#/GPIO3_13/CSI1_D19
19
GND
20
CSI1_D11
Pin
Signal
Pin
Signal
+2.775V
GND
CSI2_D12/GPIO4_9
CSI2_D13/GPIO4_10
CSI2_D14
CSI2_D15
CSI2_D16
CSI2_D17
CSI2_D18/GPIO4_11
10
CSI2_D19/GPIO4_12
11
CSI1_MCLK
12
CSI2_PIXCLK/GPIO4_15
13
CSI2_HSYNC/GPIO4_14
14
CSI2_VSYNC/GPIO4_13
15
GPIO1_2/I2SC2_SCL
16
GPIO1_3/I2C2_SDA
17
18
CAMRESET2#/APIO3_7
19
GND
20
X17 Pinout
© 2010 Digi International, Inc.
71
ConnectCore f or i .M X 5 1
Digital IO Interface
Digital I/O
Connector, X45
© 2010 Digi International, Inc.
72
ConnectCore f or i .M X 5 1
Digital I/O Connector, X45
The development board provides a 3.81mm green terminal block, X45, for accessing eight on
chip digital GPIOs of the i.MX51 CPU.
Pin
Signal
Voltage Level
GPIO3_11/SPI2_MISO/NANDF_RB3
+3.15V
GPIO3_18/NANDF_CS2#
+3.15V
GPIO3_9/SPI2_RDY/USER_LED2/NANDF_RB1
+3.15V
GPIO3_10/SPI2_SCLK/USER_LED1/NANDF_RB2
+3.15V
GPIO3_20/NANDF_CS4#
+3.15V
GPIO3_21/NANDF_CS5#
+3.15V
GPIO3_22/NANDF_CS6#
+3.15V
GPIO3_6/DISPB2_SER_DIO/USER_KEY1
+2.775
GND
0V
On the development board, GPIO3_6 is connected to USER_KEY1. When using this signal as
digital I/O, the USER_KEY1 should not be used.
Note: The digital I/O interface is not protected against ESD, over voltage or inverse polarity.
Care must be taken when using these signals.
© 2010 Digi International, Inc.
73
ConnectCore f or i .M X 5 1
Ethernet 1 Interface
Ethernet 1
RJ-45,
X7
The development board provides one 8-wire RJ-45 jack with integrated 1:1 transformers and
link/activity LEDs for the Ethernet 1 interface. This interface is attached to the Fast Ethernet
controller (FEC) of the i.MX51. The ConnectCore for i.MX51 module provides a 10/100
Ethernet PHY chip for this interface.
The Ethernet 1 RJ-45 connector also supports 802.3af (PoE).
© 2010 Digi International, Inc.
74
ConnectCore f or i .M X 5 1
Ethernet 1, RJ-45 Connector X7
The table below shows the pinout of the Ethernet 1 RJ-45 connector.
Pin
Signal
802.3af End-Span
(mode A)
802.3ad Mid-Span
(mode B)
Description
TXD+
Negative VPort
Transmit data+
TXD-
Negative VPort
Trandmit data-
RXD+
Positive VPort
Receive data+
EPWR+
Positive VPort
Power from switch+
EPWR+
Positive VPort
Power from switch+
RXD-
EPWR-
Negative VPort
Power from switch-
EPWR-
Negative VportP
Power from switch-
Receive data-
Positive VPort
The table below shows the description of the Ethernet 1 LEDs.
LED
Description
Yellow
Network activity (speed):
- Flashing - indicates network traffic
- Off - no network traffic
Green
Network link:
- On - indicates an active network link
- Off - no network link present
© 2010 Digi International, Inc.
75
ConnectCore f or i .M X 5 1
Ethernet 2 Interface
Ethernet 2
Connector, J27
The development board provides a 2x20 expansion connector for connecting an optional Digi
Ethernet adapter board (100M_ETHADPT) or customer specific setup. The Ethernet 2
interface is provided by an optional on-module Ethernet MAC/PHY.
Note: The ConnectCore for i.MX51 modules included in the development kits are supporting
the Ethernet 2 interface.
© 2010 Digi International, Inc.
76
ConnectCore f or i .M X 5 1
Ethernet 2, Connector J17
The table below shows the pinout of the Ethernet 2 expansion connector.
Pin
Signal
Pin
Signal
GND
GND
ETH2_TX+
ETH2_RX+
ETH2_TX-
ETH2_RX-
GND
GND
Reserved (ETH2_DC+)
10
Reserved (ETH2_DD+)
11
Reserved (ETH2_DC-)
12
Reserved (ETH2_DD-)
13
GND
14
GND
15
ETH2_ACTIVITY#
16
ETH2_LINK#
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
© 2010 Digi International, Inc.
77
ConnectCore f or i .M X 5 1
HDMI Interface
HDMI Connector, J19
The development board provides an HDMI interface connected to the disaply interface 1 of
the ConnectCore for 1.MX51 CPU. An Analog Devices AD9389 HDMI transmitter is used in the
development board. This HDMI transmitter is controlled through the I2C port 2 of the
ConnectCore for 1.MX51.
© 2010 Digi International, Inc.
78
ConnectCore f or i .M X 5 1
The I2C device address of the HDMI transmitter is the following:
Interface
I 2C Address (7 bits)
HDMI transmitter (AD9389)2
0 x 39
HDMI Connector, J19
The development board provides an HDMI connector, J19. THe HDMI interface is connected to
the Display 1 interface of the ConnectCore for 1.MX51 CPU.
The table below shows the pinout of the HDMI connector:
Pin
Signal
HDMI_TX2+
GND
HDMI_TX2-
HDMI_TX1+
GND
HDMI_TX1-
HDMI_TX0+
GND
HDMI_TX0-
10
HDMI_TXC+
11
GND
12
HDMI_TXC-
13
NC
14
NC
15
HDMI_SCL
16
HDMI_SDA
17
GND
18
+5V
19
HOTPLUG_DET
© 2010 Digi International, Inc.
79
ConnectCore f or i .M X 5 1
C Interface
I C Header,
P22
© 2010 Digi International, Inc.
80
ConnectCore f or i .M X 5 1
C Header, P22
Pin header P22 provides access to the i.MX51 I2C port 2 interface.
The I2C port 2 is connected to the following headers/interfaces on the development board.
Interface
I 2C Address (7 bits)
I2C Header
Camera 1
0 x5 C (Digi CC-ACC-MT9V111)
Camera 2
0 x4 8 (Digi CC-ACC-MT9V111)
HDMI Transmitter
0 x 39
LCD 1
LCD 2
Audio CODEC
0 x 1A
Peripheral connector
I2C port 2 is connected to the following interfaces of the ConnectCore for 1.MX51 module:
Interface
I 2C Address (7 bits)
Accelerometer (MMA7455L)
0 x 31D
The table below provides the pinout of connector P22:
Pin
Function
Defaults to
I2C_SDA
GPIO1_3
+2.775V
I2_SCL
GND
GPIO1_2
By default, this interface is configuresto operate in GPIO mode.
© 2010 Digi International, Inc.
81
ConnectCore f or i .M X 5 1
JTAG Interface
JTAG Interface, X13
© 2010 Digi International, Inc.
82
ConnectCore f or i .M X 5 1
Standard JTAG ARM Connector, X13
The standard JTAG ARM connector is a 20-pin header and can be used to connect
development tools (ICS) such as Ronetix PEEDI or other.
Pin
Function
Pin
Function
+1.8V
+3.3V
JTAG_TRST#
GND
JTAG_TDI
GND
JTAG_TMS
GND
JTAG_TCK
10
GND
11
Reserved (RTCK)
12
GND
13
JTAG_TDO
14
GND
15
JTAG_RESET#
16
GND
17
JTAG_DE#
18
GND
19
GND
20
GND
Note: In order to enable ETM functionality, Digi offers an optional ETM adapter board (sold
separately, Digi P/N CC-ACC-MX51-ETM). Please contact us.
© 2010 Digi International, Inc.
83
ConnectCore f or i .M X 5 1
LCD Interfaces
LCD2 Connector, P2
LCD1
Connector, P1
The development board provides two 2x40 pin, 1.27mm connectors for accessing a Digiprovided LCD application boards (CC-ACC0LCDW-70) or a user defined LCD application board.
P1
: corresponds to i.MX51 display interface 1
P2
: corresponds to i.MX51 display interface 2
© 2010 Digi International, Inc.
84
ConnectCore f or i .M X 5 1
LCD 1 Connector, P1
This connector provides access to the following capabilities:
18-bit
SPI
(RGB x 8bit) LCD
bus for a touch screen controller
Touch
screen (on-module, shared with LCD2)
Interrupt
I
input for touch screen
2
C bus
x GPIO
+3.3VDC
supply and a 9-30VDC supply
P1 Pinout
The table below shows the pinout of the LCD1 connector, P1:
Pin
Function
Pin
Function
LCD1_DATA16 (R0)
LCD1_DATA17 (R1)
LCD1_DATA12 (R2)
LCD1_DATA13 (R3)
LCD1_DATA14 (R4)
LCD1_DATA215(R5)
LCD1_DATA16 (R6)
LCD1_DATA17 (R7)
10
11
12
13
GND
14
GND
15
LCD1_DATA10 (G0)
16
LCD1_DATA11 (G1)
17
LCD1_DATA6 (G2)
18
LCD1_DATA7 (G3)
19
LCD1_DATA8 (G4)
20
LCD1_DATA9 (G5)
21
LCD1_DATA10 (G6)
22
LCD1_DATA11 (G7)
23
24
25
26
27
GND
28
GND
29
LCD1_DATA4 (B0)
30
LCD1_DATA5 (B1)
31
LCD1_DATA0 (B2)
32
LCD1_DATA1 (B3)
33
LCD1_DATA2 (B4)
34
LCD1_DATA3 (B5)
35
LCD1_DATA4 (B6)
36
LCD1_DATA75(B7)
37
38
© 2010 Digi International, Inc.
85
ConnectCore f or i .M X 5 1
Pin
Function
Pin
Function
39
40
41
GND
42
GND
43
LCD1_BIAS
44
LCD1_PCLK
45
LCD1_PWREN#
46
GND
47
LCD1_VSYNC
48
LCD1_HSYNC
49
50
51
52
53
54
55
GND
56
GND
57
TOUCH_X1
58
TOUCH_Y1
59
TOUCH_X2
60
TOUCH_Y2
2 2
61
I C _SDA
62
I2C2_SCL
63
LCD_SPI_SS#
64
SPI1_CLK
65
SPI1_MOSI
66
SPI1_MISO
67
RESET#
68
LCD1_TOUCH_INT/EXT#
69
LCD1_GPIO1
70
LCD1_GPIO2
71
LCD_PENIRQ
72
GND
73
+3.3V
74
+3.3V
75
+9-30V
76
+9-30V
77
+9-30V
78
+9-30V
79
80
© 2010 Digi International, Inc.
86
ConnectCore f or i .M X 5 1
LCD 2 Connector, P2
This connector provides access to the following capabilities:
18-bit
SPI
(RGB x 8bit) LCD
bus for a touch screen controller
Touch
screen (on-module, shared with LCD1)
Interrupt
I
input for touch screen
2
C bus
x GPIO
+3.3VDC
supply and a 9-30VDC supply
P2 Pinout
The table below shows the pinout of the LCD2 connector, P2:
Pin
Function
Pin
Function
LCD2_DATA16 (R0)
LCD2_DATA17 (R1)
LCD2_DATA12 (R2)
LCD2_DATA13 (R3)
LCD2_DATA14 (R4)
LCD2_DATA15 (R5)
LCD2_DATA16 (R6)
LCD2_DATA17 (R7)
10
11
12
13
GND
14
GND
15
LCD2_DATA10 (G0)
16
LCD2_DATA11 (G1)
17
LCD2_DATA6 (G2)
18
LCD2_DATA7 (G3)
19
LCD2_DATA8 (G4)
20
LCD2_DATA9 (G5)
21
LCD2_DATA10 (G6)
22
LCD2_DATA11 (G7)
23
24
25
26
27
GND
28
GND
29
LCD2_DATA4 (B0)
30
LCD2_DATA5 (B1)
31
LCD2_DATA0 (B2)
32
LCD2_DATA1 (B3)
33
LCD2_DATA2 (B4)
34
LCD2_DATA3 (B5)
35
LCD2_DATA4 (B6)
36
LCD2_DATA5 (B7)
37
38
© 2010 Digi International, Inc.
87
ConnectCore f or i .M X 5 1
Pin
Function
Pin
Function
39
40
41
GND
42
GND
43
LCD2_BIAS
44
LCD2_PCLK
45
LCD2_PWREN#
46
GND
47
LCD2_VSYNC
48
LCD2_HSYNC
49
50
51
52
53
54
55
GND
56
GND
57
TOUCH_X1
58
TOUCH_Y1
59
TOUCH_X2
60
TOUCH_Y2
2 2
61
I C _SDA
62
I2C2_SCL
63
LCD_SPI_SS#
64
SPI1_CLK
65
SPI1_MOSI
66
SPI1_MISO
67
RESET#
68
LCD2_TOUCH_INT/EXT#
69
LCD2_GPIO1
70
LCD2_GPIO2
71
LCD_PENIRQ
72
GND
73
+3.3V
74
+3.3V
75
+9-30V
76
+9-30V
77
+9-30V
78
+9-30V
79
LED_BCK+
80
LED_BCK-
© 2010 Digi International, Inc.
88
ConnectCore f or i .M X 5 1
MicroSD™ Card Interface
MicroSD Connector, X14
© 2010 Digi International, Inc.
89
ConnectCore f or i .M X 5 1
MicroSD™ Connector, X14
The development board provides one MicroSD™ card connector, X14. This interface is
connected to the enhanced Secured Digital Host controller 1 (eSDHC1) of the i.MX51 CPU.
The MicroSD™ connector used on the development board does not provide a card detect pin
(pin-9 and pin-10 are connected to chassis). A hot-plug insertion or removal is not possible
with this connector.
The following table shows the pinout of the MicroSD™ connector:
Pin
Signal
SD_SATA2
SD_DATA3
SD_CMD
+3.3V
SD_CLK
GND
SD_DATA0
SD_DATA1
SD_CD (Connected to chassis)
10
SD_CD (Connected to chassis)
© 2010 Digi International, Inc.
90

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : jlee2
Create Date                     : 2011:01:18 12:07:21+01:00
Modify Date                     : 2011:01:18 12:07:25+01:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Metadata Date                   : 2011:01:18 12:07:25+01:00
Creator Tool                    : FrameMaker 9.0
Format                          : application/pdf
Title                           : CC Wi-i.MX51 HRM.book
Creator                         : jlee2
Document ID                     : uuid:a684ac45-a1c8-4405-9253-a11e203fd2b8
Instance ID                     : uuid:55ec3a86-8a9a-4564-8fbc-c9a94d46ef3a
Producer                        : Acrobat Distiller 9.2.0 (Windows)
Page Count                      : 20

EXIF Metadata provided by EXIF.tools