Diversey R37615-00 Soap Dispenser with 900 MHz ISM User Manual Installation Guides

Download:
Mirror Download [FCC.gov]
Document ID	3663531
Application ID	xHTOvLKvsG0vjOyW4B3llQ==
Document Description	Installation Guides
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	173.24kB (2165522 bits)
Date Submitted	2017-12-05 00:00:00
Date Available	2018-06-03 00:00:00
Creation Date	2016-06-16 14:59:49
Producing Software	Adobe Acrobat 10.1.13 Paper Capture Plug-in
Document Lastmod	2017-12-05 12:23:14
Document Title	Installation Guides
Document Creator	Adobe Acrobat 10.1.13

UNITED STATES
CANADA
EUROPE
8215 Forest Point Blvd
Charlotte NC 28273
USA
Phone: t 1(980) 221-3236
www.sealedair.com
Address: 3755 Laird Road
Mississauga, Ontario
L5L OB3 Canada
Phone: t 1(905) 829-1200
www.sealedair.com
Maarssenbroeksedijk 2
NL- 3542DN Utrecht
The Netherlands
Phone: t31 (0)30 247 6911
www.sealedair.com
Sealed
Air
Diversey Care
J>
91-00006_Rev2
1.1 DISPENSER INSTALLATION NOTES
NOTE: SEE KEY DISPENSER DIMENSIONS BELOW (1.2). IF INSTALLING WITH DRIP CATCH OR ELBOW BAR, SEE CRmCAL DIMENSIONS BELOW (1.5 Drip·Catch and 2.2 Elbow Bar)
1. Remove key from back of housing. (Reference 'Key Location' in section 1.2, below)
2. The dispenser should be mounted 12 inches (30.5 em) above the counter-top, sink or other surface.
3. If replacing soap dispenser on wall, determine if any of the holes match up on the Sealed Air unit. Unit is designed to at least partially match numerous soap dispensers.
4. Mount the dispenser to wall using proper mounting hardware for your particular wall composition . Go to section 3.0 for specific dispenser mounting instructions.
NOTE : TAPE & SCREWS/ANCHORS ARE PROVIDED FOR INSTALLATION.
DISCLAIMER: If refills (Soap) used other than certified SA soap, SA is not responsible for any dispenser issues.
1.2 DIMENSIONS, KEY LOCATION, OPENING & CLOSING DISPENSER
1.3 REFILL PLACEMENT & REMOVAL
**KEY OUTER DIMENSIONS OF DISPENSER : 1Hl10.24" 12fD'v1Ml x 1Wl6" I152.4MMJx IDI4'' [1 01.6mml
•
'click'
6"
{152.4mm)
10.24"
{260mm)
KEY LOCATION
OPENING COVER
CLOSING COVER
Remove cover key {a) from
back of housing.
Insert key into holes
on top of cover then pull
cover forward.
To close the cover, simply PUSH the top
of cover closed to 'Click' shut {b).
TO INSERT REFILL
TO REMOVE REFILL
Push refill into place to ensure the FLANGE of the
Pull the Container {e) and the Pump
Soap Nozzle {c) is seated into the correct location {d). Housing (f). Please recycle accordingly.
If not, the dispenser will not pump correctly.
1.4 DOSE SIZE CONTROL GUIDE
**To change dose setting, open dispenser cover and slide the red Dose Control Switch {a) to your desired dose size,
1.0 ML DOSE SETIING
Ensure you slide the Control Switch {a) ALL the way to the left or right.
SLIDE DOSE CONTROL SWITCH {a )TO THE LEFTFOR 1.0ML DOSE SETIING.
SLIDE DOSE CONTROL SWITCH {a )TO THE RIGHT FOR 0.4ML DOSE SETIING.
1.5 OPTIONAL DRIP-CATCH INSTALLATION
[ 409.22]
16.111
Insert drip catch hooks (a) through rectangular
slots located at the backside of the dispenser.
The Drip-Catch with SNAP into place.
NOTE: The Drip Catch is not designed to be removed.
However, if going to remove for cleaning please be careful
not to damage the dispenser. The drip catch might
be damaged after removing.
DISCLAIMER: If other drip catch used, Sealed Air not responsible for damage.
0.4 ML DOSE SETIING
no.4
no.S-1
no.7
no.S-2
QQ
no.S-1
n0.1
Unlock and open Manual Dispenser cover
n0.2
Remove Refill Bottle
no.3
Use a drill with a 6mm bit to bore a hole in to the 2 pilot holes
located on the inside left and right sides of the housing unit.
n0. 4
Insert the Elbow Bar ends ( 4A) in to each of the holes from the
outside . NOTE: COTTER RINGS (5·1 & 5·2) ARE OPTIONAL.
(2A)
(1 A).
Insert Cotter Rings
(SA)
through Elbow Bar holes
(58).
no.S-2 Cotter Ring (SA) correctly installed close up view.
from Dispenser.
(3A)
no.6
Lift up the elbow bar to a vertical position ( 6A). Re-install the
Refill bottle ( 68) before closing the dispenser cover ( 6C).
no.7
To comp lete the installation, lower the Elbow Bar (7 A) so that
it rests in p lace on top o f the Push Lever.
NOTE: To replace refill, you must LIFT up the Elbow Bar (similar to 6A) first, then UNLOCK and LOWER the COVER.
After replacement of refill, CLOSE cover FIRST(GC) before lowering the Elbow Bar (7A).
2.2 ELBOW BAR- KEY DIMENSIONS
MANUAL DISPENSER with ELBOW BAR
FRONT VIEW KEY DIMENSIONS
[ 171 10 ]
6.736
SIDE VIEW KEY DIMENSIONS
_ [ 101.6 ] _
4.0
SJJ1J
25 8.30 ]
10 .169
iZC=I\
..1.
[ 42.11 ]
1.658
/t=:!S}'
Jl.
r---- [ 141.38 ] _ __)===~=:d...J.~
f------ - 5._56_6_
[ 242.40 l - - - -----1
9.543
3.0 DISPENSER MOUNTING INSTRUCTIONS
1. Ensure the Key is removed from the housing. See Step 1 under 3.1 Below.
2. The dispenser should be mounted 12 inches (30.5 em) above the counter-top, sink or other surface.
3. If replacing soap dispenser on wall, determine if any of the holes match up on the Sealed Air unit. Unit is designed to at least partially match numerous soap dispensers.
4. Mount the dispenser to wall using proper mounting hardware for your particular wall composition . See 3.1 (Tape Mounting Instructions) and 3.2 (Screw Mounting Instructions)
NOTE: Tape can be used effectively for installations on mirrors and tile.
3.1 TAPE MOUNTING INSTRUCTIONS
STEP I
STEP2
Step I: Ensure the back of the dispenser and
the wall is properly cleaned for installation.
Ensure that all surfaces are DRY before
mounting the dispenser.
STEP3
Step 2: Remove the white paper from
the one side of the Tape (b).
Place each piece of tape in the areas
shown with the black dotted lines (c)
Step 3: Once tape on the dispenser, remove the
remaining red backing from both pieces of tape. Last,
ensure that the dispenser is in a level position on the
wall and press the dispenser firmly for 15 to 20
seconds to allow it to properly adhere to wall.
NOTE : ENSURETHE KEY (a) IS REMOVED FROM HOUSING
It's recommended to let the dispenser set up for
24 hours before installing the refill.
3.2 SCREW MOUNTING INSTRUCTIONS
STEP I
STEP2A
STEP2B
1/4 (6.35mm)
Drill Bit
0~--
Step I:The Dispenser housing
Step 2A:Use a 1/4 (6.35mm) Step 2B:Insertanchors into
provides numerous mounting
drill bit to bore the holes on
both holes.
locations. If replacing a competitive the wall for the anchors and
unit, determine if one (or more)
screws provided.
of the holes match.
NOTE: Ensure that proper
If no holes exist on wall or do not mounting hardware is used
properly match, we suggest using
for your particular
the two holes circled above.
wall composition.
Step 3: Use a screwdriver to insert
the screws in to the anchors
and tighten the dispenser
securely against the wall.
91-00006_Rev2
Soap Dispenser Placement Requirements and
Recommendations
(See dispenser instructions in dispenser package for actual dispenser installation)
The following recommendations are intended to provide guidelines on best possible placement of
handsoap dispensers. Because every location a dispenser is to be mounted is different,
depending on customer site, physical size limitations, and available space, these
recommendations may not always be entirely possible to follow. However, when placing a soap
dispenser, the dispenser installation must meet ADA requirements and should promote ease of
use and be in union with its surroundings. Upon installation, the dispenser should be level and
the job results professional, presentable, and fully functional.
Requirements for ADA Compliance:


The dispenser must be operable with one hand.
Minimum height requirements reference the height of the activator mechanism.
o Maximum height is 48” when vanity is 20” (or less) deep.
o Maximum height is 44” when vanity is 20”-25” deep.
Restrooms





Installation must be ADA compliant.
Whenever possible, always mount the soap dispenser direct to a wall instead of a mirror or
other installed fixture.
o Always use screws to attach dispenser to wall when wall mounted.
Anytime space is available, mount dispenser just to the left or right of a mirror.
o Leave about 1/4" to 1/2" space between mirror and dispenser - just enough for it to
open/shut freely and without obstruction.
o IntelliCareTM Hybrid Dispenser’s must be mounted a minimum of 12 inches (30.5 cm)
between the bottom of the dispenser and any horizontal surface to assure proper
operation of the dispenser. (Be sure dispenser is still meeting ADA height
requirements)
When installing dispensers for sink modules with multiple wash basins, use good judgment
when determining how many dispensers should be installed. A single dispenser should be
sufficient in serving a module with two wash basins, while 2 dispensers should be sufficient
to serve a module with 3 wash basins.
o See enclosed examples for placement ideas.
Install only on a mirror when all other possibilities have been exhausted.
Food Service Areas






It is recommended to always mount a soap dispenser direct to a wall instead of the sink’s
backsplash whenever possible.
o Always use screws to attach dispenser to wall when wall mounted.
Anytime space is available, mount dispenser just to the left or right of the sink.
o Leave about 1/4" to 1/2" space between sink and dispenser - just enough for it to
open/shut without hitting the sink).
o IntelliCareTM Hybrid Dispenser’s must be mounted a minimum of 12 inches (30.5 cm)
between the bottom of the dispenser and any horizontal surface to assure proper
operation of the dispenser. (Be sure dispenser is still meeting ADA height
requirements)
Avoid mounting a dispenser too high or too low. Always attempt to mount in close
proximity of the actual use area.
Do not install a hand soap dispenser directly above any surface where food will be
prepared.
In food service areas, a hand soap dispenser (and soap) is required at every hand wash
sink.
Install only on the sink backsplash when all other possibilities have been exhausted.
Installation Examples for Restrooms
Mirror
Dispenser
Wash Basin
Single Sink
(Family restroom)
Double Sink
Triple Sink
Quadruple Sink
Helpful Tip: Installing the dispenser in line with the bottom of the mirror
(mounted over the lavatory) is always recommended. If the mirror is installed
in compliance with ADA requirements (bottom of mirror max 40” above floor),
the hand soap dispenser will be in ADA compliance. As well, this installation
creates a cleaner sight line than other options.
FCC Labeling Requirements

This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

Any intentional or unintentional radiator shall caution the user that changes or
modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the condition
that this device does not cause harmful interference.

This device has been tested according to FCC RF Exposure guidelines and meets the
applicable RF Exposure limits with all the intended use conditions for this device.
©Diversey, Inc 2017

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2016:06:16 14:59:49-05:00
Creator                         : Adobe Acrobat 10.1.13
Modify Date                     : 2017:12:05 12:23:14-05:00
Title                           : 
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2017:12:05 12:23:14-05:00
Creator Tool                    : Adobe Acrobat 10.1.13
Format                          : application/pdf
Document ID                     : uuid:03cffea5-bad5-4751-8d3f-bf9caeea3838
Instance ID                     : uuid:dfe8a1d6-89a6-458b-8606-b79b8ddb085a
Producer                        : Adobe Acrobat 10.1.13 Paper Capture Plug-in
Page Count                      : 8

EXIF Metadata provided by EXIF.tools