Electronic Systems Technology ESTEEM195EP BASE STATION TRANSMITTER User Manual CHAPTER 2

Electronic Systems Technology BASE STATION TRANSMITTER CHAPTER 2

SPECIFICATIONS

APPENDIX B SPECIFICATIONS Model 195Eg Specifications Revised: 16 Jun 06 APX B-1 EST P/N AA107P LED Indicators Power On/Off Receiver On/Off Carrier Detect On/Off Transmitter On/Off Link Status On/Off I/O Connectors Ethernet 10/100Base T RJ-45 RS-232C Programming Port RJ-45 Dual Antenna input/Outputs TNC Reverse Female Direct Input Power Header Screw Connector Transmiter Frequency of Operation 4.960 & 4.980 GHz Software Selectable with two Channels RF Data Rates 1,2,5.5,6,9, & 11 Mbps Fixed or Auto Scaling DSSS/CCK Modulation Tx Output Power 2 Watts (peak) / 1 watt (average) RF Output Impedance 50 ohms Receiver Rx Sensitivity -85 dBm @11 Mbps to –92 dBm @ 1 Mbps Frame Error Rate <10% Power Power Connector on Unit 10 to 16 VDC Receive 320 ma @ 12 VDC Transmit 1500 ma @ 12 VDC Case Dimensions 1.9 in. H x 6.7 in. W x 6.2 in. L Weight 1.25 lbs. Outdoor Pole Mounting Kit Optional, EST P/N 195PM Other Warranty 1 Year Temperature Range -30° to +60° C Humidity 95% Non-condensing FCC Type Acceptance Pending Type Acceptance Specifications Subject to Change Without Notice
APPENDIX B SPECIFICATIONS Model 195Eg Case Specifications Revised: 16 Jun 06 APX B-2 EST P/N AA107P
APPENDIX B SPECIFICATIONS Antenna Specifications Revised: 16 Jun 06 APX B-3 EST P/N AA107P Model No: AA191Ep Antenna Type: Omni-Directional, Vehicle Mount Applications: Mobile Model AA191Ep Frequency: 4.9-5.0 GHz Polarization: Vertical Caution Omni-directional antenna should not be located within 20 cm of personnel. Impedance: 50 ohms Gain: 5.5 dBi VSWR: < 1.5 Front to Back Ratio: n/a Horizontal Beamwidth: n/a Vertical Beamwidth: n/a Antenna Material: Black Radome Mounting Hardware: Base Included Antenna Connector: TNC-R Male Antenna Envelope: 12 in. length by 1.75 in width Weight: .08 lbs. Model: AA20DMEp Model AA20DMEp Applications: Model 195Ep direct case mount Antenna Type: Omni-Directional, Sleeve dipole Frequency: 4.9-5.0 GHz Caution Omni-directional antenna should not be located within 20 cm of personnel. Polarization: Vertical Impedance: 50 ohms Gain: 5.5 dBi (3.5 dBd) VSWR: < 2:1 Power: 10 W Front To Back Ratio: n/a Horizontal Beamwidth: n/a Vertical Beamwidth: n/a Antenna Material: Polyurethane Plastic Radome Recommended Mounting Hardware: n/a Antenna Connector: TNC-R Male Flexibility: +/- 20 ° Antenna Envelope: 8.28 in. length by .54 in. width Temperature: -40 to +70 C° Weight: 33 grams
APPENDIX B SPECIFICATIONS Antenna Specifications Revised: 16 Jun 06 APX B-4 EST P/N AA107P Mounting Bracket Model AA20Eg Caution To comply with the FCC exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna and all persons. Model No: AA20Ep Antenna Type: Omni Directional, DC Grounded Applications: Fixed base Frequency: 4.9-5.0 GHz Polarization: Vertical Impedance: 50 ohms Gain: 9 dBi (7dBd) VSWR: 1.2:1 Typical Front to Back Ratio: n/a Horizontal Beamwidth: n/a Vertical Beamwidth: 40 degrees @ ½ power Antenna Material: Brass radiator, UV inhibited fiberglass enclosed Mounting Hardware: Base to Mast, Supplied. Antenna Connector: TNC-R Male with 36in. pig-tail. Antenna Envelope: 12 in. length by 1 in. diameter Weight: 1.5 lbs.
APPENDIX B SPECIFICATIONS Antenna Specifications Revised: 16 Jun 06 APX B-5 EST P/N AA107P Model No: AA203Ep Caution To comply with the FCC exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna and all persons. Antenna Type: Directional, DC grounded Applications: Fixed base. Frequency: 4.9-5.0 GHz Polarization: Vertical or Horizontal Impedance: 50 ohms Gain: 9 dBi (7 dBd) VSWR: < 1.5 Model AA203Ep Front to Back Ratio: 23 dB Horizontal Beamwidth: 55 degrees @ ½ power Vertical Beamwidth: 55 degrees @ ½ power Antenna Material: Sealed in UV stable fiberglass enclosed radome Mounting Hardware: Stainless steel U bolts (included) for mounting up to 1 5/8 in. diameter pipe. Antenna Connector: TNC-R Male with 36in. pig tail Maximum Power Input: 5 Watts Antenna Envelope: 4.5 in. length by 3 in. diameter Windload (RWV): 125 mph Lateral Thrust at Rated Wind: 5.8 lbs. Wind Surface Area: 0.060 ft2Weight: 1 lbs.
APPENDIX B SPECIFICATIONS Antenna Specifications Revised: 16 Jun 06 APX B-6 EST P/N AA107P Model No: AA204Ep Applications: Fixed base mounting Antenna Type: 2.4 GHz ISM, Directional, DC Grounded, Parabolic Grid Frequency: 4.9-5.0 GHz Polarization: Vertical or Horizontal Caution To comply with the FCC exposure compliance requirements, a separation distance of at least 50 cm must be maintained between the antenna and all persons. Impedance: 50 ohms Gain: 26 dBi (24 dBd) nominal VSWR: < 1.5:1 nominal Front to Back Ratio: >24 dB Horizontal Beamwidth: 16 degrees @ ½ power Vertical Beamwidth: 11 degrees @ ½ power Antenna Material: Zinc plated cold rolled steel with polyester power coat finish Model AA204Eg Recommended Mounting Hardware: Standard U-bolt steel mast clamp complete with mounting hardware. Designed for masts of up to 2.5 in. O.D. Antenna Connector: TNC-R Male with 36 in. pig-tail Maximum Power Input: 10 Watts Wind Survival: 100 mph Wind Load: 16 mph Antenna Envelope: 34 in. length by 17 in. width by 11 in. height Weight: 3 lbs.

Navigation menu