Furuno USA 9ZWRTR087A Marine Radar User Manual inst man part 2

Download:
Mirror Download [FCC.gov]
Document ID	1456685
Application ID	egZZH8+0XnSoYIOHkZ0vkA==
Document Description	inst man part 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	156.09kB (1951121 bits)
Date Submitted	2011-04-28 00:00:00
Date Available	2011-06-22 00:00:00
Creation Date	2011-04-28 11:59:37
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2011-04-28 12:00:14
Document Title	inst man part 2

2. WIRING
2.2 Wiring the Power Supply Unit
Cabling
1. Unfasten four screws to remove the cable clamp.
2. Unfasten four screws to remove the cover.
3. Attach the connectors of three cables as shown in the figure below.
POWER Board 03P9419
J11
J4
J13
J3
J1 3P
VL3P-VV-S2X
2C-AA050
cable
(to 12-24 VDC)
J5
13
J12
J14
Ground
terminal
MJ-B24
LPF0011-050
cable
(to display unit)
Antenna cable
RW-9771
(03S9771)
4. Lay three cables in respective slots referring to the figure above.
5. Reattach the cover and the cable clamp.
6. Connect a ground wire (local supply, IV-2sq) between the ground terminal and ship’s
ground.
2-2
2. WIRING
Jumper block, slide switch setting
The jumper block JP1 and slide switch S112 on the PWR board (03P9419) must be set
according to radar model. Open the unit, locate JP1 and S112 and set them as below.
Jumper block JP1
("short" for FR-8252 radar;
remove dummy connector and
attach connector assy.
XH2P-L40-ACR.)
Slide switch S112
(Upward position
for FR-8252)
FR-8252
S112
MODEL1964C
Power supply unit, inside view
Jumper block, slide switch
JP1
Function
Enables/disables motor slow start circuit.
Setting
Short (disable)
S112
TUNE voltage selector (0-12 V, 0-32 V)
Upward position
(0-12 V)
Power requirement, replacement of fuses
Power requirement
The power for the power supply unit and display unit must be drawn from the same power
switch on the power terminal board.
Replacement of fuses
The power supply unit is shipped with a 15 A fuse(for connection to 12 VDC battery).
Replace the fuse with a 7 A (supplied) when the ship’s battery is 24 VDC.
2-3
2. WIRING
2.3 Port for External Devices
External equipments can be connected here as shown below.
NMEA1(7P)
NMEA2(7P)
NMEA sentence
device
NMEA sentence
device
HDG (6P)
Heading sensor
PC/EXT-BUZZER
(7P)
External buzzer,
PC, etc.
This equipment can receive the following NMEA 0183 format sentences from other
equipment. You will need the optional NMEA cable to connect with external equipment.
•
•
•
•
•
•
•
•
•
•
•
Course:
Waypoint
Heading (True):
Heading (Magnetic):
Ship’s speed:
Date:
Time:
Own ship’s position:
Depth:
Wind speed and angle*3:
Water temperature:
VTG> RMC
Range: BWR> BWC> RMB, Bearing: BWR> BWC (> RMB*1)
HDT> VHW> HDG*2> HDM*2> VHW*2
HDG> HDM> VHW> HDT*2> VHW*2
Over ground: VTG>RMC> VHW, Through water: VHW
ZDA
ZDA
GNS>GGA>RMC> GLL
DPT>DBT
True: MWV>VWT, Relative: MWV>VWR
MTW
*1: Available when true bearing.
*2: Variation data is required.
*3: True or Relative is changed with menu.
2-4
3. SETTING UP THE EQUIPMENT
3.1 Setting Language
At the first power application after installation, choose a language as follows.
1. Press /BRILL key to turn the power on.
“Now Initializing…” appears and after a while the window below appears.
Language
Language
Language
Language
Language
Language
Language
Language
Language
Language
Language
Language
English
Francais
Espanol
Deutsch
Italiano
Portugues
Dansk
Svensk
Norsk
Chinese
Japanese
Thai
2. Rotate the trackball to choose language desired and press the ENTER key.
The confirmation window appears.
Language English OK?
Yes
No
Changes with language chosen.
3. Choose Yes and press the ENTER key.
3-1
3. SETTING UP THE EQUIPMENT
3.2 Opening the Installation Menu
After you have installed the equipment, set it up as follows.
1. Press the MENU key. The main menu appears on the screen.
2. Rotate the trackball downward to choose Installation. The installation menu appears in
gray to right side of the screen.
3. While pressing down the CANCEL/HL OFF key, press the MENU key five times to
activate the Installation menu.
Menu
Mark
Custom 1
Custom 2
Custom 3
Tuning
GPS Buoy
Target
ARP
AIS
GPS
System
Initial
Factory
Installation
Sector Blank 1**
Installation
Language
Purpose
Type
View Position
Input Source
Antenna Height
Heading Adjust
Manual Timing Adjust
Tuning Initial Adjust
Manual MBS Adjust
Video Initial Adjust
Auto Installation Setup**
Antenna Rotation
Local Time Offset
Total TX Time*
Total On Time*
Memory Clear*
: English
: Sea
: 8062
: Center
: Main
:5m
: 0°
: 0
: 0
: Rotate
: - 0.1 H
: 000000.5 h
: 000000.6 h
[ENTER]: Enter [CANCEL/HL OFF]: Back
[MENU]: Exit
* : Displayed when scrolled.
** : Set the Sector Blank to "Off" in order to
execute Auto Installation Setup in the
Installation menu.
4.
5.
6.
7.
8.
9.
Press the ENTER key. The highlighted cursor appears in the Installation menu.
Rotate the trackball downward or upward to choose an item in the Installation menu.
Press the ENTER key to show setting window.
Rotate the trackball downward or upward to choose an option.
Press the ENTER key to confirm setting.
Finally, press the MENU key to close the main menu.
Basic Settings
Language: Choose an appropriate language.
Purpose: Choose the purpose of this radar among River, Sea and IEC. The default setting
is Sea.
River: To use this radar on a river.
Sea: To use this radar on high seas.
IEC: To use this radar as the type approved radar.
Type: Choose type of this radar among 8062 (6 kW radar), 8122 (12 kW radar) and 8252
(25 kW radar) to agree with the specifications of the antenna unit. The default setting
is 8062. Unsuitable setting may result in malfunction.
3-2
3. SETTING UP THE EQUIPMENT
View Position: Choose the operating position for this radar among Left, Left-Center, Center,
Right-Center and Right to view echo colors correctly. The default setting is Center.
Left: When operating this radar at the left side.
Left-Center: When operating this radar at the left-center side.
Center: When operating this radar at center position.
Right-Center: When operating this radar at the right-center side.
Right: When operating this radar at the right side.
Approx. angle of the view position as follows.
LCD screen
30° 0°
Left
Center
15°
Left-Center
30°
Right
15°
Right-Center
Note: The radar echo and trail echo are adjusted by the View Position. The
characters are not adjusted. This setting is also reflected on an external monitor
(option).
Input Source: Choose the input source between Main and Sub. The default setting is Main.
Main: When using this display unit as main radar.
Sub: When using this display unit as sub display. For Sub, the “Video Initial
Adjust” is required (page 3-6).
Antenna Height: Set the height of the antenna above the water surface among 5, 10, 15,
20, 30, 40 and 50 m. The default setting is 15 m.
Antenna Rotation: “Rotate,” the default setting, stops transmission when the antenna is
not rotating. “Stop” transmits radar pulses without rotating the antenna.
Local Time Offset: To display local time on the screen, set the time difference from the
UTC.
Memory Clear: Restore the default settings. However, Purpose, Type, View Position and
Input Source are not restored.
Heading Adjustment
You have mounted the antenna unit facing straight ahead in the direction of the bow.
Therefore, a small but conspicuous target dead ahead visually should appear on the
heading line (zero degrees).
In practice, you will probably observe some small error on the display because of the
difficulty in achieving accurate initial positioning of the antenna unit. The following
adjustment will compensate for this error.
1. Set ship’s heading toward a suitable target (for example, ship or buoy) at a range
between 0.125 and 0.25 nautical mile.
3-3
3. SETTING UP THE EQUIPMENT
2. Transmit the radar at 0.25 nm range and measure the bearing of that target relative to
ship’s heading with an EBL.
3. Open the Installation menu, and choose Heading Adjust.
4. Press the ENTER key to show the HEADING ADJUST window.
0°
(0 ° ∟ 359 °)
5. Rotate the trackball upward or downward to set the value measured at the step 2 above.
Confirm that the target shows dead ahead on the screen.
6. Press the ENTER key to conclude the setting.
Auto Installation Setup
When this item is executed, the tuning, timing, video and MBS are automatically adjusted.
Note: Before executing this procedure, confirm that Sector Blank 1 and Sector Blank 2 are
off.
1. Transmit the radar at 48 nm range.
2. Choose Auto Installation Setup from the installation menu and press the ENTER key.
3. Rotate the trackball to choose Yes, and then press the ENTER key.
Automatically, the tune adjustment begins, indicating “Tuning adjusting….” Then, the timing
adjustment, video adjustment and MBS adjustment are executed automatically, indicating
“Timing adjusting…”, “Video adjusting…”, and “MBS adjusting…” in that order. After the
adjustment is completed, the window disappears.
If you are not satisfied with the result of the Auto Installation Setup, execute Manual Timing
Adjust, Tuning Initial Adjust, Manual MBS Adjust and Video Initial Adjust as follows.
Tuning Initial Adjust
1. Transmit the radar at 48 nm range.
2. Open the Installation menu, and choose Tuning Initial Adjust.
3. Press the ENTER key to show the setting window.
4. Rotate the trackball to choose Yes, and then press the ENTER key. The tune
adjustment begins, indicating “Tuning adjusting….” After the adjustment is completed,
the window disappears.
3-4
3. SETTING UP THE EQUIPMENT
Manual Timing Adjust
This adjustment ensures proper radar performance, especially on short ranges. The radar
measures the time required for a transmitted echo to travel to the target and return to the
source. The received echo appears on the display based on this time. Thus, at the instant
the transmitter is fired, the sweep should start from the center of the display (sometimes
called sweep origin.)
A trigger pulse generated in the display unit goes to the antenna unit through the signal
cable to trigger the transmitter (magnetron). The time taken by the signal to travel up to the
antenna unit varies, depending largely on the length of signal cable. During this period the
display unit should wait before starting the sweep. When the display unit is not adjusted
correctly, the echoes from a straight local object (for example, a harbor wall or straight pier)
will not appear with straight edges – namely, they will be seen as “pushed out” or “pulled in”
near the picture center. The range of objects will also be incorrectly shown.
(1) Target pulled
(2) Correct
(3) Target pushed outward
Examples of improper and correct sweep timing
1. Transmit on the shortest range and confirm that gain and A/C SEA are properly
adjusted.
2. Visually select a target which forms a straight line (harbor wall, straight piers).
3. Open the Installation menu and choose Manual Timing Adjust.
4. Press the ENTER key to show the setting window.
5. Rotate the trackball to straighten the target selected at step 2, and then press the
ENTER key to finish.
3-5
3. SETTING UP THE EQUIPMENT
Manual MBS Adjust
Main bang (black hole), which appears at the display center on short ranges, can be
suppressed as follows.
1.
2.
3.
4.
5.
Transmit the radar on the short range.
Open the Installation menu and choose Manual MBS Adjust.
Press the ENTER key to show the setting window.
Rotate the trackball to suppress main bang (between 0 and 255).
Press the ENTER key to finish.
Video Initial Adjust
After completing Auto Installation Setup, you can fine tune the video signal.
1. Transmit the radar and set as follows.
Gain: one o’clock
A/C Sea: zero
A/C Rain: zero
Echo Average: Off
Noise Rejecter: Off
Interference Rejecter: Med.
2. Open the Installation menu and choose Video Initial Adjust.
3. Press the ENTER key to show the setting window.
4. Rotate the trackball to adjust the video so that the white noise slightly appears. The
setting range is 0 to 31. The greater the value, the higher the gain.
5. Press the ENTER key to finish.
Note: If the display unit is used as a Sub-display, set the “Input Source” to “Sub” and
perform the Video Initial Adjust as mentioned above so that the echo presentation on
the sub-display is the same as that on the main display.
3-6
4. OPTIONAL EQUIPMENT
4.1 ARP Kit ARP-11
The ARP kit provides automatic radar plotter functions to this radar.
Necessary parts
Name:
ARP kit
Type:
ARP-11
Code no.: 008-523-050
Contents of ARP kit
Name
ARP Board
Pan head screw
Spacer*
Spring washer*
Type
18P9014B
M3x6 C2700W
SQ-9
SQ-15
M3 C5191W
Code No.
001-068-900
000-163-189-10
000-159-320-10
000-159-299-10
000-168-187-10
Qty
*Not used
1. Unscrew all connector nuts at the rear of the display unit.
2. Unfasten all screws to remove the display cover.
03P9415
03P9413
Removing the display unit cover
3. Disconnect the printed circuit board 03P9415 and 03P9413.
Before disconnecting the 03P9413, disconnect J601 and J604 at the back of the board.
4-1
4. OPTIONAL EQUIPMENT
4. Mount the ARP board, mating with connectors and fixing it with four screws at the
location as shown in the figure below.
ARP board
5. Remount 03P9415 and 03P9413 at original position and display cover.
Note: After connecting the harness to J601 on 03P9413, bend the harness so that it does
not touch the parts on ARP board.
03P9413
J601
ARP board
Shall not touch.
4-2
4. OPTIONAL EQUIPMENT
4.2 External Monitor
You can display the radar image on an external monitor which accepts industrial standard
VGA input using the optional RGB kit OP03-195. Supply monitor and interconnection cable
(with HD-15P connectors of male, three rows of 15 pins) locally.
Necessary parts for external monitor
Name:
RGB kit
Type:
OP03-195
Code No.: 008-553-110
Name
Type
Code No.
RGB board
03P9492
008-553-680
Flat cable
SML2SC34-4X50BDP.5S4
000-155-457
Cable assy
15SDS/XHP10-005
000-144-511
EMI core
RFC-6
000-144-132-10
Qty
1. Unscrew all connector nuts at the rear of the display unit.
2. Unfasten all screws to remove the display cover.
3. Disconnect the printed circuit board 03P9415 and 03P9413.
Before disconnecting the 03P9413, disconnect J601 and J604 at the back of the board.
4. Mount the RGB board with two screws and connect the flat cable at the location shown
in the figure below.
Flat cable
RGB board
5. Remount 03P9415 and 03P9413 at their original locations and display cover.
4-3
4. OPTIONAL EQUIPMENT
6. Detach LCD panel from the above assembly. Be sure to disconnect the connector and
flat cables.
7. Connect the cable assy. 15SDS/XHP10-005 to the rear side of the RGB board.
8. Fix the shield wire of the cable assy. with a screw used to fix the RGB board.
9. Attach the EMI core RFC-1 to the cable assy. closely to the connector.
10. Pass the signal cable through the hole shown below and then pass it through the
“OPTION” port at the rear of the display unit..
RGB board (opposite side)
Fix shield wire with
a RGB board fixing bolt.
Attach EMI core closely
to the connector.
RGB cable assy.
Pass cable through here.
11. Reassemble the display unit and cover the hole with soft putty to seal.
12. Fix the EMI core RFC-6 to the cable closely to the display unit.
4-4
4. OPTIONAL EQUIPMENT
4.3 Remote Display
The FURUNO Display Unit FMD-811, MODEL1832 or GD-280/380, etc. can be connected
to this radar as a sub display. The display unit RDP-150 also can be used as a sub display.
To interconnect them, use optional cable MJ-B24LPF0008-100/200/300 (see page iv). Also,
the EMI core (option) should be attached to the remote display cable to prevent noise.
Installation materials for remote display (Type: CP03-31001、Code number: 008-556-830)
Name
Type
Code no.
Qty
1 EMI core
RFC-H13
000-146-570-10
2 Cable clamp
CK-13H
000-102-947-10
3 Cable-tie
CV-100N
000-162-167-10
4 Cable-tie
CV-150N
000-162-186-10
1. Unscrew all connector nuts at the rear of the main display unit.
2. Unfasten all screws to remove the display cover.
3. Pass the signal cable from the “OPTION” port at the rear of the display unit through the
hole shown in the figure below and then connect it to the SPU board.
4. Fix the shield wire with a screw used to fixed the SPU board.
5. Attach the EMI core RFC-H13 on the signal cable.
6. Attach cable clamp and fix the cable as shown below.
90 mm
Cable clamp
Remote display cable
EMI core
RFC-H13
Attach cable-tie approx. 90 mm from the end of
cable and attach EMI core.
Fix the EMI core with cable-tie CV-100.
4-5
4. OPTIONAL EQUIPMENT
7. Fix the signal cable to the spacer of the FIL board with a cable tie CV-150N.
Fix the cable to the spacer of FIL board
with cable-tie.
8. Reassemble the display unit.
4-6
4. OPTIONAL EQUIPMENT
4.4 External Buzzer
The optional external buzzer provides a louder alert when an alarm is violated.
External buzzer
Type: OP03-136
Code no.: 000-086-443
Further, you need the optional cable assy. MJ-A7SPF0007-050C (w/7P connector, 5 m,
code no. 000-154-028-10).
1. Attach the MJ-A7SPF0007-050C cable assy. (option) to the PC/EXT-BUZZER port at the
rear of the display unit.
2. Cut off the XH connector and cable itself (as necessary) at the end of the external
buzzer cable.
3. Solder the cables made at step 2 to the MJ-A7SPF0007-050C cable as shown below.
Red
Soldering
MJ-A7SPF0007-050C
External buzzer
Black
Other wires should be cut off,
and wrap here with vinyl tape.
Connection of external buzzer and display unit
using cable assy. type MJ-A7SPF0007-050C cable
4. Attach the buzzer to the mounting location with double-sided tape or two self-tapping
screws (3x15 or 3x20, local supply).
4-7
4. OPTIONAL EQUIPMENT
This page is intentionally left blank.
4-8
0#/'
&1%7/'06

,

%

/,#52(<%

%2

%2
%2

52

4&2,'
&'5%4+26+10%1&'Íł
4&2,'
㩿㪁㪈㪀
3 6;
䯴⇛࿑䬽ኸᴺ䬾䫺ෳ⠨୯䬶䬨䫻䎃䎧䎬䎰䎨䎱䎶䎬䎲䎱䎶䎃䎬䎱䎃䎧䎵䎤䎺䎬䎱䎪䎃䎩䎲䎵䎃䎵䎨䎩䎨䎵䎨䎱䎦䎨䎃䎲䎱䎯䎼䎑䯵
㩿㪁㪈㪀䈱ᦠ㘃䈲䇮๺ᢥ઀᭽ኾ↪
㩿㪁㪈㪀㩷㪤㪘㪩㪢㪜㪛㩷㪛㪦㪚㪬㪤㪜㪥㪫㪪㩷㪘㪩㪜㩷㪝㪦㪩㩷㪡㪘㪧㪘㪥㪜㪪㪜㩷㪪㪜㪫㩷㪦㪥㪣㪰㪅
䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪠㪥㪞㩷㪮㪠㪫㪟㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪩㪜㪧㪩㪜㪪㪜㪥㪫㪘㪫㪠㪭㪜㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅
#22.+%#6+10)7+&'
ᛛㆡ⹺⸽ⷐ㗔
(.75*/1706+0)6'/2.#6'
㩖㩡㨹㩆㨷㩙㨽㩧㩎㩠㨽ဳ⚕
࿑ᦠ
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ/,
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
176.+0'
+056#..#6+10/#6'4+#.5
52#4'2#465
70+6
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
Ꮏ੐᧚ᢱ
52#4'2#465
੍஻ຠ
੍஻ຠ
&+52.#;70+6
ᜰ␜ㇱ
࡙࠾࠶࠻
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
176.+0'

+/ 

15 

1/ 

%
&'5%4+26+10%1&'Íł

3 6;
䎷䎺䎲䎃䎷䎼䎳䎨䎶䎃䎤䎱䎧䎃䎦䎲䎧䎨䎶䎃䎰䎤䎼䎃䎥䎨䎃䎯䎬䎶䎷䎨䎧䎃䎩䎲䎵䎃䎤䎱䎃䎬䎷䎨䎰䎑䎃䎃䎷䎫䎨䎃䎯䎲䎺䎨䎵䎃䎳䎵䎲䎧䎸䎦䎷䎃䎰䎤䎼䎃䎥䎨䎃䎶䎫䎬䎳䎳䎨䎧䎃䎬䎱䎃䎳䎯䎤䎦䎨䎃䎲䎩䎃
䎷䎫䎨䎃䎸䎳䎳䎨䎵䎃䎳䎵䎲䎧䎸䎦䎷䎑䎃䎴䎸䎤䎯䎬䎷䎼䎃䎬䎶䎃䎷䎫䎨䎃䎶䎤䎰䎨䎑
)6:
ဳᑼ䎒䱤䱚䱮䲈⇟ภ䬛䯾Ბ䬽႐ว䫺ਅᲑ䭗䭙਄Ბ䬺ઍ䭞䭚ㆊᷰᦼຠ䬶䬑䭙䫺䬸䬰䭘䬚䬛౉䬲䬵䬓䭍䬨䫻䫹䬹䬙䫺ຠ⾰䬾ᄌ䭞䭙䭍䬪䭢䫻
+056#..#6+10/#07#.
ⵝ஻ⷐ㗔ᦠ
12'4#614 5)7+&'
ᠲ૞ⷐ㗔ᦠ
12'4#614 5/#07#.
016+%'(14(75'
4'2.#%'/'06
ขᛒ⺑᣿ᦠ
㩕㨷㨺㩇㩨ᄌᦝߩ߅㗿޿
0#/'
)6: 
A-1
࡙࠾࠶࠻
176.+0'
+056#..#6+10/#6'4+#.5
70+6

%2

45$
&'5%4+26+10%1&'Íł
)6:
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪠㪥㪞㩷㪮㪠㪫㪟㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪩㪜㪧㪩㪜㪪㪜㪥㪫㪘㪫㪠㪭㪜㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅
#06'00#+056#..#6+10/#6'4+#.5
ⓨਛ✢ㇱᎿ᧚
Ꮏ੐᧚ᢱ
#06'00#70+6
ⓨਛ✢ᧄ૕ㇱ
0#/'
45$45$45$45$
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
)6: 
3 6;

A-2
0#/'
176.+0'
#06'00#+056#..#6+10/#6'4+#.5
70+6
#-: 

%2

:0###
&'5%4+26+10%1&'Íł
3 6;

䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
#-:
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪠㪥㪞㩷㪮㪠㪫㪟㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪩㪜㪧㪩㪜㪪㪜㪥㪫㪘㪫㪠㪭㪜㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
㨻㩧㩍㩏Ꮏ᧚
#06'00#
㨻㩧㩍㩏
࡙࠾࠶࠻
:0#:0#:0#:0#0%-&:0#0%-&
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
A-3









ᢙ㊂
3 6;
↪ㅜ㧛஻⠨
4'/#4-5







%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ
'/+%14'
'/+㩄㨻
'/+%14'
'/+㩄㨻
*':#)10#.*'#&$1.6
౐ⷺ㩘㩨㩣㩎
*':#)10#.076
౐ⷺ㩏㨹㩎㩆㨷
(.#69#5*'4
㩚㩀㩨㩁ᐔᐳ㊄
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'






%1&'01 

49
49
%1&'01
4(%*
%1&'01
4(%
%1&'01
/:575
%1&'01
/575
%1&'01
/575
%1&'01
/575
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
3 6;
↪ㅜ㧛஻⠨
4'/#4-5
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)6:
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)6:
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'

⇟ภ
01

)6: 
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
%1&'01
/:%9/$0+
%1&'01
/:575
%1&'01
/575
%1&'01
/575
%1&'01
/575
%1&'01

%1&'01
41*5
%1&'01
41*5
%1&'01
41*5
%1&'01
41*5
ဳฬ㧛ⷙᩰ
&'5%4+26+105
%2
6;2'
A-5
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
9#5*'4*'#&5%4'9 $
㩏㩗㩨㩈㩛㩇$
*':#)10*'#&5%4'9
౐ⷺ㩘㩨㩣㩎ో㩒㩆㩨
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
*':#)10#.076
౐ⷺ㩏㨹㩎㩆㨷
(.#69#5*'4
㩚㩀㩨㩁㩙㩣ᐔᐳ㊄
-01$%#2
㩁㨶㨹㩖㩩
5*+'.&%.#/2
㩆㨺㩣㩎㩨㩂㩡㩧㩖㩩
2#%-+0)(+:674'
㩔㩩㨹㩁㩧㨿㩅㨾
%14415+102411(
47$$'4/#6
㒐ⲁࠧࡓ
5'#.9#5*'4
㩆㨺㩣㩦㨹㩆㨶㨺
⇛‫ޓޓ‬࿑
176.+0'

%1&'01
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬

ฬ‫ޓޓ‬⒓
0#/'
+056#..#6+10/#6'4+#.5
⇟ภ
01
+056#..#6+10/#6'4+#.5

)6: 
Ꮏ੐᧚ᢱ⴫
%2
6;2'
Ꮏ੐᧚ᢱ⴫

%1&'01
A-4
6*4'#&'&41&
ኸಾ㩘㩨㩣㩎
9+0)076
಄㑆࿶ㅧⲔ㩏㨹㩎
(.#69#5*'4
㩚㩀㩨㩁ਣᐔᐳ㊄
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
5'.(6#22+0)5%4'9
㩎㩡㩇㩊㨹㩕㩩㩧㩒㩆㩨‫ޓ‬㩆㨷
47$$'4%75*+10 
㒐ᝄ㩄㩨㩛 
47$$'4%75*+10
㒐ᝄ㩄㩨㩛 
⇛‫ޓޓ‬࿑
176.+0'






%1&'
01

/:575
%1&'
01
/575
%1&'
01
/575
%1&'
01
/575
%1&'
01
:575
%1&'
01

%1&'
01

ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
3 6;
↪ㅜ㧛஻⠨
4'/#4-5
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)6:
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/'
ฬ‫ޓޓ‬⒓
0#/'
(.75*/1706+0)5210)'
(㩙㨽㩧㩎㩠㨽㩇㩘㩩㩧㩆㩨
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
ဳฬ㧛ⷙᩰ
&'5%4+26+105
%2

%1&'01

41*5
6;2'
%1&'01
ᢙ㊂
3 6;
↪ㅜ㧛஻⠨
4'/#4-5

)6: 
A-7
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)6:
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
⇟ภ
01
+056#..#6+10/#6'4+#.5
⇟ภ
01
+056#..#6+10/#6'4+#.5

)6: 
Ꮏ੐᧚ᢱ⴫
%2
6;2'
Ꮏ੐᧚ᢱ⴫

%1&'01
A-6

⇟ภ
01
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ/,
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ/,
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ/,
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ/,
⇛‫ޓޓ‬࿑
176.+0'




ᢙ㊂
3 6;
)6:
ㆬᛯ‫ޓޓޓޓޓޓޓޓ‬
61$'5'.'%6
ㆬᛯ‫ޓޓޓޓޓޓޓޓ‬
61$'5'.'%6
ㆬᛯ‫ޓޓޓޓޓޓޓޓ‬
61$'5'.'%6
ㆬᛯ‫ޓޓޓޓޓޓޓޓ‬
61$'5'.'%6
↪ㅜ㧛஻⠨
4'/#4-5

㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
%1&'01
/,$.2(
%1&'01
/,$.2(
%1&'01
/,$.2(
%1&'01
/,$.2(
ဳฬ㧛ⷙᩰ
&'5%4+26+105
)6: 
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
ฬ‫ޓޓ‬⒓
0#/'
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
(4
%1&'01
6;2'
A-8
⇟ภ
01
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ
⇛‫ޓޓ‬࿑
176.+0'




ᢙ㊂
3 6;
#8:
ㆬᛯ‫ޓޓޓޓޓޓޓޓ‬
61$'5'.'%6'&
ㆬᛯ‫ޓޓޓޓޓޓޓޓ‬
61$'5'.'%6'&
ㆬᛯ‫ޓޓޓޓޓޓޓޓ‬
61$'5'.'%6'&
ㆬᛯ‫ޓޓޓޓޓޓޓޓ‬
61$'5'.'%6'&
↪ㅜ㧛஻⠨
4'/#4-5

㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
%1&'01
49 /
%1&'01
49 /
%1&'01
49 /
%1&'01
49 /
ဳฬ㧛ⷙᩰ
&'5%4+26+105
#8: 
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
ฬ‫ޓޓ‬⒓
0#/'
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
(4
%1&'01
6;2'
A-9
&1%7/'06
+056#..#6+10/#6'4+#.5
52#4'2#465
70+6
176.+0'

%

%

%2

/,$.2( 4

8.2885:%##
%2

52

257
&'5%4+26+10%1&'Íł
#8: 
3 6;

䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
#8:
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
+06'40#.5'66+0) ,4'0
⸳ቯⷐ㗔ᦠ
016+(+%#6+10&1%7/'06
㩕㨷㨺㩇㩨ᄌᦝߩ߅㗿޿
࿑ᦠ
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
5+)0#.%#$.'#55'/$.;
㩃㨺㩖㩨㩣⚵ຠ/,
%#$.'#55'/$.;
㩃㨺㩖㩨㩣㩂㩚㩕㩧
Ꮏ੐᧚ᢱ
52#4'2#465
੍஻ຠ
੍஻ຠ
219'45722.;70+6
ⓨਛ✢㔚Ḯㇱ
࡙࠾࠶࠻
0#/'
257
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
A-10
%100'%614#55;
㩄㩒㩂㩊⚵ຠ
5'.(6#22+0)5%4'9
㩎㩡㩇㩊㨹㩕㩩㩧㩒㩆㩨‫ޓ‬㩆㨷
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'

%1&'
01

:*2.#%4
%1&'
01
:575
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
3 6;
%2
6;2'
↪ㅜ㧛஻⠨
4'/#4-5
#8: 

㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
#8:
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/'
⇟ภ
01
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫

%1&'01
A-11
(75'
㩕㨷㨺㩇㩨
(75'
㩕㨷㨺㩇㩨
()$1#
#%8
()$8
#2$(
()$1#
#%8
()$8
#2$(
2'4
8'5




(75'
㩀㩧㨼㩢㩕㨷㨺㩇㩨
(75'
㩕㨷㨺㩇㩨
(75'
㩕㨷㨺㩇㩨
()$1##%8
()$18#
2$(
()$1##%8
()$8#
2$(
()$1#
#%8
()$8
#2$(
&9)01
14
6;2'01
2'4
8'5







5'652'4
8'55'.
4'/#4-5%1&'01
#3:
52#4'
#3:  
$1:012
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌ
ࠊࠅ߹ߖࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'
722'4241&7%637#.+6;+56*'5#/'
&9)01
2'4
5'6
914-+0)
37#06+6;
75'
52

㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)‫(ޓ‬144'('4'0%'10.;㧕
(74701'.'%64+%%1.6&
176.+0'
52#4'2#465.+56(14
0#/'1(
2#46
/(4 50#/'
+6'/
01
5*+201
6;2'
%1&'01
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌ
ࠊࠅ߹ߖࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'
722'4241&7%637#.+6;+56*'5#/'

5'652'4
8'55'.
4'/#4-5%1&'01
)6:
52#4'
)6:  
$1:012
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)‫(ޓ‬144'('4'0%'10.;㧕
&9)01
2'4
5'6
914-+0)
37#06+6;
75'
52
6;2'
&9)01
14
6;2'01
(74701'.'%64+%%1.6&
176.+0'
52#4'2#465.+56(14
0#/'1(
2#46
/(4 50#/'
+6'/
01
5*+201

%1&'01
A-12
A-13
,WN4'UWOK
D-1
Y. Hatai
D-2
Y. Hatai
D-3
Y. Hatai
D-4
Y.Hatai
D-5
C
MJ-A3SPF0018-050ZC,5m,φ10
造船所手配。
オプション。
コネクタは工場にて取付済み。
シールドは両端で完全にアースする。
ＥＭＩコアを取り付ける。
*3
MJ-A7SPF
WHT
BLU
YEL
GRN
RED
BLK
*3
MJ-A6SPF
シロ WHT
クロ BLK
キ YEL
ﾐﾄﾞﾘ GRN
*2
MJ-A7SPF0007-050C
シロ
5m,φ7
アオ
キ
ﾐﾄﾞﾘ
外部ブザー
1m
アカ RED
アカ
EXT. BUZZER
クロ BLK
クロ
OP03-136 *2
*2
MJ-A6SPF0003-050C/100C
5/10m,φ6
*2
MJ-A6SPF0007-100C
10m,φ6
リモートコントローラ
REMOTE CONTROLLER
RCU-019
*2
ヘディングセンサー
HEADING SENSOR
PG-1000 *2
A-Dコンバータ
A-D CONVERTER
AD-100 *2
NOTES
*1: SHIPYARD SUPPLY.
*2: OPTION.
*3: FITTED AT FACTORY.
*4: GROUND SHIELD EFFECTIVELY AT BOTH ENDS.
*5: ATTACH EMI CORES.
注記
*１)
*２)
*３)
*４)
*５)
選択
SELECT
ジャイロ
GYRO
*3
MJ-A7SPF
WHT
BLU
YEL
GRN
RED
BLK
*2
MJ-A7SPF0007-050C
シロ
5m,φ7
アオ
キ
ﾐﾄﾞﾘ
アカ
クロ
航法装置
NAV EQUIPMENT
(NMEA0183)
*5
POWER
(+)
(-)
GND
*5
DWG.No.
SCALE
C3539-C01- G
MASS
H.MAKI
kg
REF.No.
ﾐﾄﾞﾘ（太）GRY(B)
ダイ（太）ORG(B)
T.YAMASAKI
*4
ORG
ドウジク COAX.
キ
YEL
ダイ
モモ（太）PNK(B)
アカ
RED
ハイ（太）GRY(B)
ﾑﾗｻｷ（太）PPL(B)
ｷﾐﾄﾞﾘ(太) L-GRN(B)
シロ
WHT
アオ（太）BLU(B)
クロ
BLK
ﾑﾗｻｷ（太）PPL(B)
*4
*5
*5
*5
NAME
名 称
TITLE
INTERCONNECTION DIAGRAM
MARINE RADAR
FR-8062/8122
船舶用レーダー
相互結線図
RW-4747
RTB 03P9405A
J821(VH9P)
1 +12V
2 +12V
3 GND
4 -12V
5 -12V
6 TX-TRIG.
7 P/L-A
8 P/L-B
9 NC
J823(VH4P)
1 BP
2 MOTOR+
3 HD.
4 MOTORJ824(NH13P)
1 TUNE-IND.
2 MOTOR3 NC
4 MOTOR+
5 MBS-L
6 MOTOR+
7 NC
8 GND
9 NC
10 NC
11 GND
12 VIDEO
13 TUNE-CONT
J822(VH2P)
1 -12
2 +12
空中線部 ANTENNA UNIT
RSB-0070/0073
(RTR-085A/086A)
03-167-6003-3
MJ-B24LPF0012,10/15/20/30m,φ11
(RW-9807,21C+2C2V,30m MAX.)
キ （太）YEL(B)
クロ（太）BLK(B)
アカ（太）RED(B)
シロ（太）WHT(B)
チャ（太）BRN(B)
チャ
BRN
アオ
BLU
ミドリ
GRN
25/Mar/2011
CHECKED
25/Mar/2011
APPROVED
DRAWN
*1
IV-2sq.
13
12
21
16
RGB 03P9429 DJ-1
10
J802
*2
11
1 R
20
2 GND
14
3 G
15
4 GND
5 B
6 GND
7 H_SYNC
8 GND
9 V_SYNC
10 GND
17
SPU 03P9411
15
J110(NH8P)
1 GND *2
18
2 TRU-HD
22
3 GND
23
4 DP-BP
19
5 GND
6 PR-TRIG
7 GND
8 VIDEO
24
指示部
DISPLAY UNIT
RDP-150
PC/EXT-BUZZER
SD
RD
REMOTE-KEY
NC
+12V
EXT.BUZZER
SHIELD
HDG
DATA-H
DATA-C
CLK-H
CLK-C
NC
GND
NMEA2
TD2-A
TD2-B
RD2-H
RD2-C
+12V
SG
SHIELD
NMEA1
TD1-A
TD1-B
RD1-H
RD1-C
+12V
SG
SHIELD
MJ-B24LPF0008
10/20/30m,φ11.4
*3
MJ-A7SPF
WHT
BLU
YEL
GRN
RED
BLK
*1
IV-2sq.
*3
10A:24V
MJ-A3SPF
15A:12V
シロ WHT
クロ BLK
19S1004,0.5m *5
*1
SVGAモニター SVGA MONITOR CABLE
Dsub15P
SVGA MONITOR
副指示器
*2
REMOTE DISPLAY
航法装置
MJ-A7SPF0007-050C
NAV EQUIPMENT
シロ
5m,φ7
(NMEA0183)
アオ
キ
ﾐﾄﾞﾘ
アカ
クロ
SUPPLY UNIT
PR-240 *2
100/110/115/ DPYC-1.5 *1 7 AC/DC電源 24V(+) 3
220/230 VAC
(-) 2
6 ユニット
AC/DC POWER
1φ,50/60Hz
12-24 VDC
S-1
C
注記
*１)
*２)
*３)
*４)
*５)
NOTE
造船所手配。
*1: SHIPYARD SUPPLY.
オプション。
*2: OPTION.
コネクタは工場にて取付済み。
*3: FITTED AT FACTORY.
シールドは両端で完全にアースする。 *4: GROUND SHIELD EFFECTIVELY AT BOTH ENDS.
ＥＭＩコアを取り付ける。
*5: ATTACH EMI CORES.
*1
IV-2sq.
VL3P-VV-S2X2C-AA050,5m,φ10
(03S9801)
*3
10A:24V
MJ-A3SPF
POWER
15A:12V
指示部
MJ-A3SPF0018-050ZC
1 (+)
シロ WHT
12-24 VDC
DISPLAY UNIT
5m,φ10
2 (-)
クロ BLK
RDP-150
*1
3 GND
100/110/115/ DPYC-1.5 7 AC/DC電源 24V(+) 3
RGB 03P9429
220/230 VAC
(-) 2
6 ユニット
J802
*5
*5
AC/DC
POWER
*2
19S1004,0.5m
1φ,50/60Hz
1 R
SUPPLY UNIT
GND
PR-240 *2
*1
*5
MJ-B24LPF0008
3 G
IV-2sq.
DJ-1
10/20/30m,φ11.4
*1
10
4 GND
SVGAモニター SVGA MONITOR CABLE
Dsub15P
11
5 B
SVGA MONITOR
20
6 GND
副指示器
*3
*2
NMEA1
14
7 H_SYNC
REMOTE DISPLAY 航法装置
MJ-A7SPF
MJ-A7SPF0007-050C
15
8 GND
1 TD1-A
NAV EQUIPMENT
シロ WHT
5m,φ7
(NMEA0183)
9 V_SYNC
2 TD1-B
アオ BLU
10 GND
3 RD1-H
キ YEL
4 RD1-C
ﾐﾄﾞﾘ GRN
5 +12V
SPU 03P9411
アカ RED
6 SG
クロ BLK
J110(NH8P)
1 GND *2
7 SHIELD
2 TRU-HD
*3
*2
17
NMEA2
3 GND
MJ-A7SPF
航法装置
MJ-A7SPF0007-050C
15
4 DP-BP
1 TD2-A
NAV EQUIPMENT
シロ WHT
5m,φ7
(NMEA0183)
5 GND
2 TD2-B
アオ BLU
18
6 PR-TRIG
3 RD2-H
キ YEL
22
7 GND
4 RD2-C
ﾐﾄﾞﾘ GRN
23
8 VIDEO
5 +12V
アカ RED
19
6 SG
クロ BLK
7 SHIELD
*3
A-Dコンバータ
*2
HDG
MJ-A6SPF
ジャイロ
A-D CONVERTER
MJ-A6SPF0003-050C/100C
24
1 DATA-H
シロ WHT
GYRO
AD-100 *2
5/10m,φ6
12
2 DATA-C
クロ BLK
選択
*2
13
3 CLK-H
キ YEL
ヘディングセンサー
SELECT
MJ-A6SPF0007-100C
21
4 CLK-C
HEADING SENSOR
ﾐﾄﾞﾘ GRN
10m,φ6
PG-1000 *2
16
5 NC
6 GND
*3
*2
リモートコントローラ
PC/EXT-BUZZER
MJ-A7SPF
MJ-A7SPF0007-050C
REMOTE CONTROLLER
1 SD
シロ WHT
RCU-019
*2
5m,φ7
2 RD
アオ BLU
3 REMOTE-KEY
キ YEL
4 NC
ﾐﾄﾞﾘ GRN
外部ブザー
1m
5 +12V
アカ RED
アカ RED
EXT. BUZZER
6 EXT.BUZZER
クロ BLK
クロ BLK
OP03-136 *2
7 SHIELD
DWG.No.
SCALE
APPROVED
CHECKED
DRAWN
*4
7A:24V
15A:12V
H.MAKI
C3541-C01- H
kg
Y.NISHIYAMA
REF.No.
*4
WHT
BLU[B]
BLK
PPL[B]
2C-2V COAX.
YEL
ﾄﾞｳｼﾞｸ
キ
NAME
名 称
TYPE
*4
*5
*5
*5
J820(VH2P)
TX-HV
NC
RW-4747
RTB 03P9405B
J824(NH13P)
TUNE_IND.
MOTOR(-)OUT
NC
MOTOR+
MBS_L
MOTOR+
NC
GND
NC
NC
VIDEO_GND
VIDEO
TUNE_CONT
J823(VH4P)
BP
MOTOR+
HD
MOTOR-
J821(VH9P)
+12V
+12V
GND
-12V
-12V
TX_TRIG
P/L A
P/L B
10
11
12
13
空中線部
ANTENNA UNIT
RSB-0073/RTR-087A
INTERCONNECTION DIAGRAM
MARINE RADAR
相互結線図
船舶用レーダー
FR-8252
ダイ（太）ORG[B]
WHT/ORG
ｼﾛ/ﾀﾞｲ
ｼﾛ/ｱｶ(太) WHT/RED[B]
RED
アカ
モモ(太) PNK[B]
ｼﾛ/ﾁｬ
WHT/BRN
ﾐﾄﾞﾘ(太) GRN[B]
シロ
アオ(太)
クロ
ﾑﾗｻｷ(太)
RW-9771,10/15/20/30m,φ14.5
(17C+2C2V,MAX.30m)
キ（太） YEL[B]
クロ（太）BLK[B]
アカ（太）RED[B]
シロ（太）WHT[B]
チャ（太）BRN[B]
BRN
チャ
BLU
アオ
GRN
ﾐﾄﾞﾘ
FURUNO ELECTRIC CO., LTD.
03-167-6005-3
*1
IV-2sq.
J12(VH10P)
(-)
J2(VL3P)
J3(VH9P)
+12V
+12V
GND
10
-12V
-12V
J13(VH5P)
TX-TRIG.
P/L-A
P/L-B
NC
J4(VH4P)
BP
J14(NH14P)
MOTOR+
HD.
MOTOR4
J5(NH13P)
TUNE-IND.
MOTORNC
MOTOR+
MBS-L
10
MOTOR+
NC
11
GND
12
NC
13
NC
14
GND
J11(VH2P)
VIDEO
TUNE-CONT
J1(VL3P)
(+)
PWR 03P9419
10
11
12
13
空中線電源部
PSU-008
POWER SUPPLY UNIT
T.YAMASAKI
MASS
24/Jan/2011
25/Mar/2011
25/Mar/2011
*4
MJ-B24LPF0011-050
5m,φ11
S-2

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2011:04:28 12:00:14-07:00
Create Date                     : 2011:04:28 11:59:37-07:00
Metadata Date                   : 2011:04:28 12:00:14-07:00
Format                          : application/pdf
Document ID                     : uuid:1570fc35-ed53-4814-9d03-fd751a228fc0
Instance ID                     : uuid:1473fc59-1003-4282-adfb-9b338f1e6e6d
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Has XFA                         : No
Page Count                      : 31

EXIF Metadata provided by EXIF.tools