Furuno USA 9ZWRTR088B Transceiver for Radar model FR-8045 User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2264463
Application ID	jrLbbUTbfDUOzxjedrNjFA==
Document Description	User Manual I Part 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	231.45kB (2893146 bits)
Date Submitted	2014-05-13 00:00:00
Date Available	2014-11-08 00:00:00
Creation Date	2014-05-13 13:03:46
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2014-05-13 13:04:42
Document Title	untitled
Document Creator	FrameMaker 7.2

2.
CABLE CONNECTION
AND WIRING
2.1
Standard Connection
Connect all necessary cables, using the figure and table below for reference.
CAUTION
Ground the
equipment to
prevent
interference.
No.
Description
Antenna cable to antenna unit (FR-8045)
Antenna cable to antenna unit. (FR-8065/8125)
Antenna cable to antenna unit. (FR-8255)
USB (Used by service man only).
Heading Sensor. (AD-10 format)
NMEA1 input/output. (Navigational equipment)
NMEA2 input/output. (Navigational equipment)
Option. (External buzzer, Remote display)
Power in. To ship’s power (pos = white, neg = black)
Grounding. Connect from here to ship’s terminal.
20
Cable Required
MJ-B24LPF0005-*+R
*: 50/100/150/200/300
MJ-B24LPF0012-*+R
*: 100/150/200/300
• MJ-B24LPF0011-050+R
• RW-9771 (10m, 15m, 20m, 30m)
• VL3P-VV-S2X2C-AA050
(MJ-A6SPF0007-100C)
(MJ-A7SPF0007-050C)
(MJ-A7SPF0007-050C)
(See section 4.2 for cabling.)
(MJ-A3SPF0017-050ZC)
IV-2sq.
2. CABLE CONNECTION AND WIRING
2.2
Wiring the Power Supply Unit (FR-8255 only)
2.2.1
Cabling
1. Unfasten four screws to remove the cable clamp.
2. Unfasten four screws to remove the cover.
3. Attach the connectors of three cables as shown in the figure below.
POWER Board 03P9419
J11
J4
J13
J3
J1 3P
VL3P-VV-S2X
2C-AA050
cable
(to 12-24 VDC)
J5
13
J12
J14
Ground
terminal
MJ-B24
LPF0011-050
cable
(to display unit)
Antenna cable
RW-9771
(03S9771)
4. Lay three cables in respective slots referring to the figure above.
5. Reattach the cover and the cable clamp.
6. Connect a ground wire (local supply, IV-2sq) between the ground terminal and
ship’s ground.
21
2. CABLE CONNECTION AND WIRING
2.2.2
Jumper block, slide switch setting
The jumper block JP1 and slide switch S112 on the PWR board (03P9419) must be
set according to radar model. Open the unit, locate JP1 and S112 and set them as
below.
Jumper block JP1
("short" for FR-8255 radar;
remove dummy connector
and attach connector
assy. XH2P-L40-ACR.)
Slide switch S112
(Set to upward position
for “FR-8252”)
Jumper block,
slide switch
JP1
S112
2.2.3
Function
Setting
Enables/disables motor slow start circuit. Short (disable)
TUNE voltage selector (0-12 V, 0-32 V) Upward position (0-12 V)
Power requirement, replacement of fuses
Power requirement
The power for the power supply unit and display unit must be drawn from the same
power switch on the power terminal board.
Replacement of fuses
The power supply unit is shipped with a 15 A fuse(for connection to 12 VDC battery).
Replace the fuse with a 7 A (supplied) when the ship’s battery is 24 VDC.
22
2. CABLE CONNECTION AND WIRING
2.3
Data Signals
Position
Course true
Course magnetic
Speed over the ground
Water speed and heading
Distance to waypoint
Destination waypoint, true
Destination waypoint, magnetic
Heading (true)
Heading (magnetic)
Magnetic variation
Cross-track error
Depth
Temperature
Wind (true)
Wind (relative)
Time
GNS>GGA>RMC> GLL
VTG>RMC
VTG>RMC (true)
VTG>RMC
VHW
BWR>BWC>RMB
BWR>BWC>RMB
BWR>BWC
THS>HDT>VHW (true)>HDG>HDM>VHW (magnetic)
HDG> HDM>VHW (magnetic)THS>HDT>VHW (true)
HDG>RMC
XTE>RMB
DPT>DBT
MTW
MWV>VWT
MWV>VWR
ZDA
2.4
Input/Output Ports
2.4.1
HDG port
This port is for AD-10 format.
Parameter
Rating
Forward
50mA
Current
Reverse
6V
Voltage
Forward
1.1V (TYP)
Voltage
1.4V (MAX)
Remarks
Absolute
Maximum
Absolute
Maximum
IF=4mA
Parameter
Rating
Forward
50mA
Current
Reverse
6V
Voltage
Forward
1.1V (TYP)
Voltage
1.4V (MAX)
Remarks
Absolute
Maximum
Absolute
Maximum
IF=4mA
Circuit Diagram
490Ί
GYRO_DATA_H
Photocoupler
GYRO_DATA_C
Circuit Diagram
490Ί
GYRO_CLK_H
Photocoupler
GYRO_CLK_C
23
2. CABLE CONNECTION AND WIRING
2.4.2
NMEA1 ports
Transmitter
This port complies with “IEC 61162-1 Ed4”.
Parameter
“H” level
output current
“L” level
output current
Differential
output voltage
Rating
-60mA
Remarks
Absolute
Maximum
Absolute
Maximum
Load 54Ί
60mA
1.5V (MIN)
5V (MAX)
Circuit Diagram
Differential Driver
TD1_A
TD1_B
Receiver
This port complies with “IEC 61162-1 Ed4”.
Parameter
Forward
Current
Reverse
Voltage
Forward
Voltage
2.4.3
Rating
50mA
6V
1.1V (TYP)
1.4V (MAX)
Remarks
Absolute
Maximum
Absolute
Maximum
IF=4mA
Circuit Diagram
490Ί
RD1_H
Photocoupler
RD1_C
NMEA2 ports
This port complies with “IEC 61162-1 Ed4”.
Circuit specification is the same as NMEA1 port.
24
3.
EQUIPMENT SETTINGS
3.1
Setting the Language
After installation, on first power-up, select a language as follows:
1. Press the
/BRILL key to turn on the power.
"Now Initializing" appears and after a short time the window below appears.
2. Use the CursorPad to select a language required and press the ENTER key.
The window shown below appears.
Language English OK?
Yes
No
Language selected
3. Select [Yes] and press the ENTER key.
25
3. EQUIPMENT SETTINGS
3.2
How to Set the Purpose
1. Press the MENU key. The main menu will appear on the screen.
2. Press the S or T button to select [Factory]. The factory menu title bar will appear
in gray color right side of the screen.
3. Hold down the CANCEL/HL OFF key and press the MENU key five times to activate the [Factory] menu.
The model name depends on your radar model.
Do not change the model name.
Factory
Menu
ARPA
AIS
GPS
System
Initial
Tests
Sector Blanks
Units
Installation
Factory
Language
Purpose
Model
: English
: Sea
: 8065 RTR-085A
[Enter]: Enter [CANCEL/HL OFF]: Back
[Menu]: Exit
Use this menu when setting up in factory
4. Press the ENTER key. The [Factory] menu becomes active and the cursor moves
to the right-hand column.
5. Press S or T to select [Purpose].
6. Press the ENTER key to show the setting window.
River
Sea
IEC
Russian River
7. Press S or T to select the purpose required.
8. Press the ENTER key to set the purpose.
9. Press the CANCEL/HL OFF key to return to the main menu.
26
3. EQUIPMENT SETTINGS
3.3
How to Enter Initial Settings
After you complete setting the radar purpose, enter the Initial Settings as follows:
1. On the main menu, press S or T to select [Installation].
Page 1
Menu
Installation
ARPA
AIS
GPS
System
Initial
Tests
Sector Blanks
Units
Installation
Factory
Input Source
ARPA QV Select
Demo Mode
Antenna Rotation
Antenna Height
Near STC Level
A/C Auto Adjust
Heading Adjust
Timing Adjust
[ENTER]: Enter
[MENU]: Exit
: Master
: Off
: Off
: Rotate
: 15m
:2
: 0
: 0.0°
: 0.00 NM
[CANCEL/HL OFF]: Back
Use this menu when installing on site
Page 2 (Displayed when scrolled down)
Menu
ARPA
AIS
GPS
System
Initial
Tests
Sector Blanks
Units
Installation
Factory
MBS Adjust
Video Init Adjust
ARPA Adjust SP
ARPA Adjust MP
ARPA Adjust LP
Auto Install Setup
Total On Time
Total TX Time
Memory Clear
[ENTER]: Enter
[MENU]: Exit
[CANCEL/HL OFF]: Back
Restoring the default settings
Set the [Sector Blank] to [Off] in order to
execute [Auto Installation Setup] in the
[Installation] menu.
2. Press the ENTER key. The [Installation] menu becomes active and the cursor
moves to the right-hand column.
3. Press S or T to select an item from the [Installation] menu.
4. Press the ENTER key to show the settings window.
5. Press S or T to select an option.
6. Press the ENTER key to set the option.
7. Press the MENU key to close the main menu.
27
3. EQUIPMENT SETTINGS
Basic settings
[Input source]: Select the input source from [Master] and [Slave]. The default setting
is [Master].
Master
The display unit operates as the main radar.
Slave
The display unit operates as a remote display. For remote displays, adjust
the [Video Init Adjust] and [Timing Adjust].
(See page 30 and page 29, respectively.)
[ARPA QV Select]: Set to [On] to display quantized video on the screen. Set to [Off]
for normal use.
[Demo Mode]: Set to [On] to active demo mode. Set to [Off] for normal use.
[Antenna Rotation]: [Rotate] (default setting) transmits the radar pulses by rotating
the antenna. [Stop] transmits the radar pulses without rotating the antenna.
[Antenna Height]: Set the height of the antenna above the water surface. The options
are 5, 10, 15, 20, 30, 40 and 50m. The default setting is 15m.
[Near STC level]: Set the STC curve to a near distance. The options are 1, 2, 3 and
4. “4” has the strongest effect.
[A/C Auto Adjust]: Adjust the performance of the automatic A/C.
[Memory Clear]: Restore the default settings. [Purpose], [Type] and [Source] are not
changed. When turning on the power after a memory clear, the language selection
window appears. (See page 25.)
Heading adjustment
Ensure you have installed the antenna unit correctly, so that the unit faces towards the
bow of the ship. A target at the front of the ship, aligned with the bow, must appear on
the heading line (zero degrees). If the target does not appear on the heading line, follow the procedure below to adjust the heading.
1. Set the ship toward an acceptable target (for example, a ship at anchor or a buoy)
at a range between 0.125 and 0.25 nautical miles.
2. Transmit the radar at a range setting of 0.25 nautical miles and measure the bearing of that target relative to the ship using an EBL.
3. Open the [Installation] menu and select [Heading Adjust].
4. Press the ENTER key to show the setting window for [Heading Adjust]. (See figure
below)
0.0°
(0.0°~359.9°)
5. Press S or T to set the value measured in step 2. Check that the target appears
on the heading line. If necessary repeat steps 1 to 5.
6. Press ENTER to complete the adjustment.
28
3. EQUIPMENT SETTINGS
How to automatically set the equipment
The equipment can automatically adjust the tuning, timing and video.
Note: Before you proceed, transmit the radar for more than 10 minutes on a long
range and ensure [Sector Blank] is set to [OFF].
1. Transmit on the maximum range.
2. Select [Auto Install Setup] from the [Installation] menu and press ENTER.
The tuning adjustment begins automatically and the message "Tuning adjusting" appears during the tuning adjustment stage. After the tuning adjustment is complete, the
timing and video are adjusted, in that order. The messages "Timing adjusting" and
"Video adjusting" will appear during those stages of the [Auto Install Setup]. After all
the adjustments are completed, the window disappears.
Note: If any of the results require adjustment for your conditions, use the manual adjustment procedures below to manually adjust them.
Manual timing adjustment
This adjustment gives correct radar performance on short ranges. The radar measures the time required for a transmitted echo to go to the target and return to the
source. The received echo appears on the display according to the measured time.
The sweep must start from the center of the display.
A trigger pulse created in the display unit goes to the antenna unit through the signal
cable to activate the transmitter (magnetron). The time taken by the signal to move to
the antenna unit changes, according to the length of the signal cable. During this period, the display unit must wait before the radar starts the sweep. When the display
unit is not adjusted correctly, the echoes from a straight object will not appear as a
straight line. The target appears "pushed" or "pulled" near the picture center. The
ranges to objects are also shown at wrong distances. Below are examples of wrong
and correct sweep timings.
(1) Target pulled
(2) Correct
(3) Target pushed outward
1. Transmit on the shortest range, then adjust the gain and the A/C SEA.
2. Visibly select a target that creates a straight single line, such as harbor walls or
straight piers.
3. Open the [Installation] menu and select [Timing Adjust].
4. Press ENTER to show the setting window.
5. Press S or T to until the target selected in step 2 is shown as a straight line.
6. Press ENTER to complete the adjustments.
29
3. EQUIPMENT SETTINGS
Manual MBS adjustment
Reduce the main bang (black hole), which appears at the display on short ranges, as
follows:
1. Transmit the radar on the shortest range.
2. Open the [Installation] menu and select [MBS Adjust].
3. Press ENTER to show the setting window.
4. Use the S or T to adjust the main bang (between 0 and 25).
5. Press ENTER to finish.
Manual video adjustment
Use the following procedure to manually adjust the video settings if necessary:
1. Transmit the radar and adjust the following settings:
Gain
A/C Sea
A/C Rain
Echo Average
Noise Rejector
Interference Rejector
85 to 90
zero
zero
OFF
OFF
2. Open the [Installation] menu and select [Video Init Adjust].
3. Press ENTER to show the setting window.
4. Press S or T to adjust the white noise on the display. The setting range is 0 to
31. A larger value increases the gain.
5. Press ENTER to finish.
Note: If the display is used as a remote display, set [Input Source] to [Slave]. follow
the above procedure to adjust the video and take care to ensure the remote display
output is similar to the master display output.
ARPA adjustment
During the sea trial, adjust the threshold level of the ARPA for short pulse, middle
pulse and long pulse.
• Default setting is 2.
• If the ship echoes are difficult to acquire at setting level 2, adjust to level 1.
• If the ARPA symbol moves to a different echo at setting level 2, adjust to level 3.
30
4.
OPTIONAL EQUIPMENT
4.1
ARP Kit ARP-11
The ARP kit provides automatic radar plotter functions to this radar.
Necessary parts
Name
Type
Code No.
ARP kit
ARP-11
008-523-050
For the contents of the kit, see the packing list attached to the kit.
1. Unscrew 12 screws and five connector nuts at the rear of the display unit. (See
the figure below.)
Connector nuts x 5
Do not remove
this nut
Screws x 12
2. Lift the cover slowly and open it as shown below, taking care not to damage the
SPU cables.
Open i
thi
sd
ire
Clear cover
ion
ct
SPU Cables
31
4. OPTIONAL EQUIPMENT
3. Mate P107 on the ARP Circuit-board with J214 on the 03P9586 Board and fasten
with four screws.
ARP board
Confirm that the rubber gasket is set
securely in the groove around the panel.
4. Reassemble the display unit, taking care not to exceed the torque requirements
for each connector nut. (See the figure below for nut torque.)
Torque
2.94Âą0.29 Nm
Torque
0.78Âą0.08 Nm
Torque
0.78Âą0.08 Nm
(12 pcs)
32
4. OPTIONAL EQUIPMENT
4.2
Connection of Buzzer and/or Remote Display
You will need the cables shown below to connect the optional external buzzer and remote display.
• Two-way cable MJ-A10SPFW0001 +R
• MJ-A7SPF0007-050C
• MJ-B24LPF0010-xxx+R (000: 100, 200, or 300)
MJ-A10SPFW0001+R * (0.2 m)
Display unit
RDP-154
MJ-A7SPF0007-050C (5 m)
Connection Port
MJ-10P
External buzzer
MJ-7P
OPTION
MJ-10P
MJB24P
Remote Display
MJ-B24LPF0010-xxx+R (10/20/30 m)
(xxx: 100, 200 or 300)
*: This cable is not required to connect the remote display only.
External buzzer
When a target enters, or exits, in the target zone, the optional external buzzer gives a
loud alarm.
Type
Code No.
Name
Buzzer
Cable tie
Heat-shrink-tube
Double-sided tape
OP03-21
000-030-097
Type
PKB42SWH2940
CV-70N
3x0.25 BLK
9760
Code No.
000-153-221-10
000-162-185-10
000-165-283-10
000-800-851-00
Qty
Comment
One NH connector attached
40 mm
25 mm × 25 mm
Attach the two-way cable and MJ-A7SPF0007-050C cable to the OPTION port at the
rear of the display unit. See the above figure.
1. Cut the NH connector at the end of the external buzzer cable to an acceptable
length.
2. Solder the external buzzer cable to the MJ-A7SPF0007-050C cable as shown below. Before you solder the cores, cut the heat-shrink-tube in half and set the tubes
to the cores of the cable. Solder the cores, then set the tubes on the soldered
point.
Red
MJ-A7SPF0007-050C
Black
Solder
External buzzer
Cut other cables off, and wrap here with tape.
3. Fasten the buzzer with the double-sided tape or two self-tapping screws (3x15 or
3x20, local supply).
33
NAME
DOCUMENT
RDP-154
000-178-502-1*
OME-36320-*
000-178-501-1*
OMJ-36320-*
001-258-010-00
CP03-35601
000-157-995-10
MJ-A3SPF0017-050ZC
001-258-020-00
FP03-12301
001-258-000-00
SP03-17701
000-024-819-00
RDP-154-*
**
DESCRIPTION/CODE №

(*2)
(*1)
Q'TY
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
2.(*1)の書類は、和文仕様専用
2.(*1) MARKED DOCUMENTS ARE FOR JAPANESE SET ONLY.
1.ｺ-ﾄﾞ番号末尾の[**]は、選択品の代表ｺｰﾄﾞを表します。
1.CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.
OPERATOR'S MANUAL (EN)
取扱説明書(英)
OPERATOR'S MANUAL (JP)
取扱説明書(和)
図書
OUTLINE
INSTALLATION MATERIALS
ACCESSORIES
SPARE PARTS
UNIT
INSTALLATION MATERIALS
工事材料
CABLE ASSY.
ｹｰﾌﾞﾙ組品MJ
工事材料
ACCESSORIES
付属品
付属品
SPARE PARTS
予備品
予備品
DISPLAY UNIT
指示部
ユニット

NAME
OUTLINE
000-178-509-1*
C32-01308-*
000-178-512-1*
IZS-36320-*
000-178-507-1*
IME-36320-*
000-178-506-1*
IMJ-36320-*
000-178-504-1*
NZS-36320-*
000-178-505-1*
MLG-36320-*
000-178-503-1*
OSJ-36320-*
000-178-511-1*
OZS-36320-*
DESCRIPTION/CODE №
1/1
(*3)
(*2)
(*1)
(*3)
(*2)
(*1)
(*3)
Q'TY
C3632-Z01-A
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF
THE UPPER PRODUCT. QUALITY IS THE SAME.
型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりません。
3.(*2)の書類は、英文仕様専用
3.(*2) MARKED DOCUMENTS ARE FOR ENGLISH SET ONLY.
4.(*3)の書類は、中文仕様専用
4.(*3) MARKED DOCUMENTS ARE FOR CHINESE SET ONLY.
FLUSH MOUNTING TEMPLATE
ﾌﾗｯｼｭﾏｳﾝﾄ型紙
INSTALLATION MANUAL
(CN)
装備要領書(中)
INSTALLATION MANUAL
(EN)
装備要領書(英)
INSTALLATION MANUAL
(JP)
装備要領書(和)
OPERATOR'S GUIDE (CN)
操作要領書(中)
OPERATOR'S GUIDE (MLG)
操作要領書(多言語)
OPERATOR'S GUIDE (JP)
操作要領書(和)
OPERATOR'S MANUAL (CN)
取扱説明書(中)
03HM-X-9851 -0
A-1
࡙࠾࠶࠻
#06'00#70+6+056#..#6+10/#6'4+#.5
70+6
176.+0'

%2

45$# #
&'5%4+26+10%1&'Íł
3 6;
%<#
%<#
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩

/:575

/575

12




&'5%4+26+10%1&'Íł

䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
176.+0'
(.75*/1706+0)‫ޓ‬2#465
*/: 
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
*':#)10#.*'#&$1.6
౐ⷺ㩇㩢㩦㩢㩘㩨㩣㩎
(.#69#5*'4
㩚㩀㩨㩁ਣᐔᐳ㊄
(.75*/1706(+:674';
(㩙㨽㩧㩎㊄ౕ⚵ຠ
(.75*/17065210)'8
(㩙㨽㩧㩎㩇㩘㩩㩧㩆㩨8
(.75*/17065210)'*
(㩙㨽㩧㩎㩇㩘㩩㩧㩆㩨*
0#/'
㩖㩡㨹㩆㨷㩙㨽㩧㩎ㇱຠ
12
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
A-2
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
3 6;

ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪠㪥㪞㩷㪮㪠㪫㪟㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪩㪜㪧㪩㪜㪪㪜㪥㪫㪘㪫㪠㪭㪜㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅
+056#..#6+10/#6'4+#.5
ⓨਛ✢ㇱᎿ᧚
ⓨਛ✢ㇱᎿ᧚
#06'00#70+6
ⓨਛ✢ᧄ૕ㇱ
0#/'
45$#45$#45$#45$#
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
)6: 
A-3
30/Oct/2013 H.MAKI
D-1
Y. Hatai
D-2
27/Nov/2013 H.MAKI
D-3
27/Nov/2013 H.MAKI
D-4
C
サテライトコンパス
SATELLITE COMPASS
SC-50/100 *2
MJ-B24LPF0010-**0+R
10/20/30m,φ11
MJA7SPF0007-050C,5m
外部ブザー
EXT. BUZZER
OP03-21 *2
*2
MJ-A6SPF0003-050C/100C
5/10m,φ6
*2
MJ-A6SPF0007-100C
10m,φ6
副指示器
*2
REMOTE DISPLAY
ヘディングセンサー
HEADING SENSOR
PG-500/1000 *2
A-Dコンバータ
A-D CONVERTER
AD-100 *2
NOTE
*1: SHIPYARD SUPPLY.
*2: OPTION.
*3: GROUND SHIELD EFFECTIVELY AT BOTH ENDS.
MJ-A10SPF
W0001+R
MJ-A6SPF
WHT
BLK
YEL
GRN
10
シロ
クロ
キ
ﾐﾄﾞﾘ
MJ-A7SPF
WHT
BLU
YEL
GRN
RED
BLK
*2
MJ-A7SPF0007-050C
シロ
5m,φ7
アオ
キ
ﾐﾄﾞﾘ
*2
アカ
MJ-A6SPF0007-100C
クロ
10m,φ6
航法装置
NAV EQUIPMENT
(NMEA0183)
MJ-A7SPF
WHT
BLU
YEL
GRN
RED
BLK
10
MJ-A3SPF
10A
シロ WHT
クロ BLK
*2
MJ-A7SPF0007-050C
シロ
5m,φ7
アオ
キ
ﾐﾄﾞﾘ
アカ
クロ
航法装置
NAV EQUIPMENT
(NMEA0183)
注記
*１) 造船所手配。
*２) オプション。
*３) シールドは両端で完全にアースする。
ジャイロ
GYRO
選択
SELECT
1 整流器 *2(+) 5
2 RECTIFIER (-) 6
RU-3423
*1
IV-2sq.
24 VDC MJ-A3SPF0017-050ZC,5m,φ10
*1
100-115/
220-230VAC DPYC-1.5
1φ,50/60Hz
HDG
GYRO_DATA-H
GYRO_DATA-C
GYRO_CLK-H
GYRO_CLK-C
NC
SHIELD
EXT-BUZZ/
SUB DISPLAY
NC
SHIELD
OP_TRIG
OP_BP
OP_VIDEO_GND
OP_VIDEO
OP_HD
GND
EXT_BUZZ_12V
EXT_BUZZER
NMEA2
TD2-A
TD2-B
RD2-H
RD2-C
NMEA2_12V
NMEA2_GND
SHIELD
*1
IV-2sq.
*3
DWG.No.
SCALE
H.MAKI
T.YAMASAKI
C3635-C01- B
MASS
kg
REF.No.
パソコン（保守用）
PC FOR MAINTENANCE
24/Jan/2014 H.MAKI
24/Jan/2014
CHECKED
24/Jan/2014
APPROVED
TYPE A
ﾐﾄﾞﾘ（太）GRN(B)
ダイ（太）ORG(B)
13
12
WHT/ORG
ドウジク COAX.
キ
YEL
ｼﾛ/ﾀﾞｲ
WHT/RED
RED
ORG
21
16
24
ｼﾛ/ｱｶ
アカ
ダイ
ｼﾛ/ﾁｬ
ﾑﾗｻｷ
18
22
23
19
WHT/BRN
PPL
シロ
WHT
アオ（太）BLU(B)
クロ
BLK
ﾑﾗｻｷ（太）PPL(B)
*3
NAME
名 称
TITLE
INTERCONNECTION DIAGRAM
MARINE RADAR
FR-8045
船舶用レーダー
相互結線図
RW-4747,0.3m
RTB 03P9249
J821(VH9P)
+12V
+12V
GND
-12V
-12V
TX_TRIG
PL-A
PL-B
NC
J823(VH4P)
BP
MOTOR-H
HD
MOTOR-C
J824(SH13P)
TUNE-IND
MOTOR-C
NC
MOTOR-H
MBS-L
MOTOR-H
NC
GND
NC
10
NC
11
GND
12
VIDEO
TUNE_CONT
13
J822(VH2P)
-12V
+12V
空中線部 ANTENNA UNIT
RSB-0073(RTR-088B)
03-185-6002-0
MJ-B24LPF0005-**0+R,5/10/15/20/30m,φ11
(21C+2C2V)
キ （太）YEL(B)
クロ（太）BLK(B)
アカ（太）RED(B)
シロ（太）WHT(B)
チャ（太）BRN(B)
チャ
BRN
アオ
BLU
ミドリ
GRN
17
10
11
20
14
15
DRAWN
USB
DJ-1
指示部
DISPLAY UNIT
RDP-154
NMEA1
TD1-A
TD1-B
RD1-H
RD1-C
NMEA1_12V
NMEA1_GND
SHIELD
POWER
(+)
(-)
GND
S-1
C
サテライトコンパス
SATELLITE COMPASS
SC-50/100 *2
MJ-B24LPF0010-**0+R
10/20/30m,φ11
MJA7SPF0007-050C,5m
外部ブザー
EXT. BUZZER
OP03-21 *2
*2
MJ-A6SPF0003-050C/100C
5/10m,φ6
*2
MJ-A6SPF0007-100C
10m,φ6
副指示器
*2
REMOTE DISPLAY
ヘディングセンサー
HEADING SENSOR
PG-500/1000 *2
A-Dコンバータ
A-D CONVERTER
AD-100 *2
NOTE
*1: SHIPYARD SUPPLY.
*2: OPTION.
*3: GROUND SHIELD EFFECTIVELY AT BOTH ENDS.
MJ-A10SPF
W0001+R
MJ-A6SPF
WHT
BLK
YEL
GRN
10
シロ
クロ
キ
ﾐﾄﾞﾘ
MJ-A7SPF
WHT
BLU
YEL
GRN
RED
BLK
*2
MJ-A7SPF0007-050C
シロ
5m,φ7
アオ
キ
ﾐﾄﾞﾘ
*2
アカ
MJ-A6SPF0007-100C
クロ
10m,φ6
航法装置
NAV EQUIPMENT
(NMEA0183)
10
MJ-A3SPF
シロ WHT
クロ BLK
MJ-A7SPF
WHT
BLU
YEL
GRN
RED
BLK
10A
*2
MJ-A7SPF0007-050C
シロ
5m,φ7
アオ
キ
ﾐﾄﾞﾘ
アカ
クロ
航法装置
NAV EQUIPMENT
(NMEA0183)
MJ-A3SPF0017-050ZC,5m,φ10
1 整流器 *2(+) 5
2 RECTIFIER (-) 6
RU-3423
*1
IV-2sq.
注記
*１) 造船所手配。
*２) オプション。
*３) シールドは両端で完全にアースする。
ジャイロ
GYRO
選択
SELECT
24 VDC
*1
100-115/
220-230VAC DPYC-1.5
1φ,50/60Hz
HDG
GYRO_DATA-H
GYRO_DATA-C
GYRO_CLK-H
GYRO_CLK-C
NC
SHIELD
EXT-BUZZ/
SUB DISPLAY
NC
SHIELD
OP_TRIG
OP_BP
OP_VIDEO_GND
OP_VIDEO
OP_HD
GND
EXT_BUZZ_12V
EXT_BUZZER
NMEA2
TD2-A
TD2-B
RD2-H
RD2-C
NMEA2_12V
NMEA2_GND
SHIELD
*1
IV-2sq.
DWG.No.
SCALE
C3632-C01- B
MASS
kg
24/Jan/2014 H.MAKI
H.MAKI
REF.No.
03-185-6003-0
パソコン（保守用）
PC FOR MAINTENANCE
T.YAMASAKI
TYPE A
24/Jan/2014
CHECKED
24/Jan/2014
APPROVED
DRAWN
USB
ﾐﾄﾞﾘ（太）GRN(B)
ダイ（太）ORG(B)
13
12
COAX.
YEL
ORG
ﾄﾞｳｼﾞｸ
キ
ダイ
21
16
*3
ﾑﾗｻｷ
PPL
ｷﾐﾄﾞﾘ(太) L-GRN(B)
18
22
23
19
24
シロ
WHT
アオ（太）BLU(B)
クロ
BLK
ﾑﾗｻｷ（太）PPL(B)
17
モモ（太）PNK(B)
アカ
RED
ハイ（太）GRY(B)
アカ（太）RED(B)
シロ（太）WHT(B)
チャ（太）BRN(B)
チャ
BRN
アオ
BLU
ミドリ
GRN
20
14
15
MJ-B24LPF0012-**0+R,5/10/15/20/30m,φ11
DJ-1
(21C+2C2V)
指示部
10
キ （太）YEL(B)
DISPLAY UNIT
11
クロ（太）BLK(B)
RDP-154
NMEA1
TD1-A
TD1-B
RD1-H
RD1-C
NMEA1_12V
NMEA1_GND
SHIELD
POWER
(+)
(-)
SHIELD
*3
NAME
名 称
TITLE
INTERCONNECTION DIAGRAM
MARINE RADAR
FR-8065/8125
船舶用レーダー
相互結線図
RW-4747,0.3m
RTB 03P9405A
J821(VH9P)
+12V
+12V
GND
-12V
-12V
TX-TRIG.
PL-A
PL-B
NC
J823(VH4P)
BP
MOTOR-H
HD.
MOTOR-C
J824(SH13P)
TUNE_IND
MOTOR-C
NC
MOTOR-H
MBS-L
MOTOR-H
NC
GND
NC
10
NC
11
GND
12
VIDEO
TUNE_CONT
13
J822(VH2P)
-12V
+12V
空中線部 ANTENNA UNIT
RSB-0070/0073
(RTR-085A/086A)
S-2
C
MJA7SPF0007-050C,5m
外部ブザー
EXT. BUZZER
OP03-21 *2
NOTE
*1: SHIPYARD SUPPLY.
*2: OPTION.
*3: GROUND SHIELD EFFECTIVELY AT BOTH ENDS.
注記
*１) 造船所手配。
*２) オプション。
*３) シールドは両端で完全にアースする。
MJ-B24LPF0010-**0+R
10/20/30m,φ11
*2
MJ-A6SPF0003-050C/100C
5/10m,φ6
*2
MJ-A6SPF0007-100C
10m,φ6
副指示器
*2
REMOTE DISPLAY
ヘディングセンサー
HEADING SENSOR
PG-500/1000 *2
A-Dコンバータ
A-D CONVERTER
AD-100 *2
MJ-A6SPF
WHT
BLK
YEL
GRN
10
MJ-A10SPF
W0001+R
シロ
クロ
キ
ﾐﾄﾞﾘ
MJ-A7SPF
WHT
BLU
YEL
GRN
RED
BLK
*2
MJ-A7SPF0007-050C
シロ
5m,φ7
アオ
キ
ﾐﾄﾞﾘ
*2
アカ
MJ-A6SPF0007-100C
クロ
10m,φ6
航法装置
NAV EQUIPMENT
(NMEA0183)
選択 サテライトコンパス
SELECT SATELLITE COMPASS
SC-50/100 *2
ジャイロ
GYRO
MJ-A7SPF
WHT
BLU
YEL
GRN
RED
BLK
*2
MJ-A7SPF0007-050C
シロ
5m,φ7
アオ
キ
ﾐﾄﾞﾘ
アカ
クロ
10
*1
IV-2sq.
HDG
GYRO_DATA-H
GYRO_DATA-C
GYRO_CLK-H
GYRO_CLK-C
NC
SHIELD
EXT-BUZZ/
SUB DISPLAY
NC
SHIELD
OP_TRIG
OP_BP
OP_VIDEO_GND
OP_VIDEO
OP_HD
GND
EXT_BUZZ_12V
EXT_BUZZER
NMEA2
TD2-A
TD2-B
RD2-H
RD2-C
NMEA2_12V
NMEA2_GND
SHIELD
USB
DJ-1
指示部
DISPLAY UNIT
RDP-154
NMEA1
TD1-A
TD1-B
RD1-H
RD1-C
NMEA1_12V
NMEA1_GND
SHIELD
POWER
(+)
(-)
GND
VL3P-VV-S2X2C-AA050,5m,φ10
MJ-A3SPF
MJ-A3SPF0017-050ZC, 10A
シロ WHT
5m,φ10
クロ BLK
航法装置
NAV EQUIPMENT
(NMEA0183)
24 VDC
24 VDC
24
12
13
21
16
*3
DWG.No.
SCALE
C3634-C01- B
MASS
kg
24/Jan/2014 H.MAKI
H.MAKI
T.YAMASAKI
パソコン（保守用）
PC FOR MAINTENANCE
24/Jan/2014
CHECKED
24/Jan/2014
APPROVED
DRAWN
TYPE A
REF.No.
03-185-6004-0
*1
IV-2sq.
J1(VL3P)
(+)
J12(VH10P)
(-)
J2(VL3P)
J3(VH9P)
+12V
+12V
10
GND
-12V
J13(VH5P)
-12V
TX_TRIG
PL-A
PL-B
NC
J4(VH4P) J14(NH14P)
BP
MOTOR-H
HD
MOTOR-C
J5(NH13P)
TUNE_IND
MOTOR-C
NC
MOTOR-H
10
MBS-L
MOTOR-H
11
NC
12
GND
13
NC
14
NC
J11(VH2P)
GND
VIDEO
*3
TUNE_CONT
PWR 03P9419
10
11
12
13
18
22
23
19
*3
MJ-B24LPF0011-050+R
5m,φ11
7A
空中線電源部
PSU-008
POWER SUPPLY UNIT
17
10
11
20
14
15
COAX.
YEL
WHT/ORG
NAME
名 称
TITLE
*3
J822(VH2P)
TX-HV
NC
RW-4747
J824(SH13P)
TUNE_IND
MOTOR-C
NC
MOTOR-H
MBS-L
MOTOR-H
NC
GND
NC
NC
GND
VIDEO
TUNE_CONT
J823(VH4P)
BP
MOTOR-H
HD
MOTOR-C
10
11
12
13
RTB 03P9405
J821(VH9P)
+12V
+12V
GND
-12V
-12V
TX-TRIG.
PL-A
PL-B
NC
空中線部 ANTENNA UNIT
RSB-0070/0073(RTR-087A)
INTERCONNECTION DIAGRAM
MARINE RADAR
FR-8255
船舶用レーダー
相互結線図
ダイ（太）ORG(B)
ﾄﾞｳｼﾞｸ
キ
ｼﾛ/ﾀﾞｲ
ｼﾛ/ｱｶ(太) WHT/RED(B)
アカ
RED
モモ（太）PNK(B)
ｼﾛ/ﾁｬ
WHT/PPL
ﾐﾄﾞﾘ（太）GRN(B)
シロ
WHT
アオ（太）BLU(B)
クロ
BLK
ﾑﾗｻｷ（太）PPL(B)
RW-9771,10/15/20/30m,φ14.5
(17C+2C2V,MAX.30m)
キ （太）YEL(B)
クロ（太）BLK(B)
アカ（太）RED(B)
シロ（太）WHT(B)
チャ（太）BRN(B)
チャ
BRN
アオ
BLU
ミドリ
GRN
S-3
The paper used in this manual
is elemental chlorine free.
ポFURUNO Authorized Distributor/Dealer
9-52 Ashihara-cho,
Nishinomiya, 662-8580, JAPAN
All rights reserved.
Printed in Japan
A : JAN . 2014
A1 : FEB . 07, 2014
Pub. No. IME-36320-A1
( GREG )
FR-8045/8065/8125
0 0 0 1 7 8 5 0 7 1 0

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2014:05:13 13:03:46+09:00
Creator                         : FrameMaker 7.2
Modify Date                     : 2014:05:13 13:04:42+09:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2014:05:13 13:04:42+09:00
Creator Tool                    : FrameMaker 7.2
Format                          : application/pdf
Title                           : untitled
Document ID                     : uuid:37e8d7b4-d66a-46d1-8bcd-37466e359d21
Instance ID                     : uuid:72a5523e-6d53-48c0-834d-560329c07fd4
Producer                        : Acrobat Distiller 7.0 (Windows)
Page Count                      : 24

EXIF Metadata provided by EXIF.tools