Futaba R6308SBT-24G Radio Control User Manual

Futaba Corporation Radio Control Spec

a href="https://usermanual.wiki/Futaba" itemprop="url"> Futaba >

Contents

User Manual

Applicable systems: Futaba FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) system transmitter R6308SBT FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) System with TelemetryS.BUS2 / S.BUS Port and 8 Channels for Conventional System ReceiverCompliance Information Statement (for U.S.A.)This device, trade name Futaba Corporation of America, model number R6308SBT, complies with part15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation.(3) This module meets the requirements for a mobile device that may be used at separation distances of more than 20cm from human body.To meet the RF exposure requirements of the FCC this device shall not be co-located with another transmitting device.The responsible party of this device compliance is:Futaba Service Center3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)R6308SBT SpecicationsFASST-2.4GHz system(7CH/8CH/10CH/Multi-ch mode)/S.BUS2 and S.BUS port and 8 channels for conventional system receiver• Dual antenna diversity• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)• Weight: 0.38 oz. (10.9g)• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V)•  Battery  F/S  Voltage:  3.8V  *The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S function doesn't work properly when other type battery is used.• Extra Voltage port: 0 ~70V DC* Be sure that when using ESCs regulated output the capacity of the ESC must meet your usage condition.Thank you for purchasing a Futaba R6308SBT FASST-2.4GHz compatible receiver. The R6308SBT receiver features bi-directional communication with a telemetry receiver unit (option) using the S.Bus2 port.  Using the S.Bus2 port an impressive array of telemetry sensors may be utilized.  It also includes both standard PWM output ports and S.Bus output ports. This receiver distinguishes automatically FASST-2.4-GHz system 7ch or Multi-ch/10ch / 8ch mode at the time of link operation with a transmitter. And high speed mode can be chosen.LED IndicationGreen Red StatusOff Solid No signal receptionSolid Off Receiving signalsblink Off ID of a signal is disagreementAlternate blink Unrecoverable error (EEPROM, etc.)(Antenna installation)90˚Please refer the table below for LED status vs receiver's condition.1M23N17459S.BUS2portS.BUS port(8/SB)(S.BUS2)R6308SBTS.BUS ServoS.BUS GyroHUBHUBHUBHUBExtra VoltagePortLink/Mode switchAntennaLEDServo for conventionalsystemChannel1 outputChannel8 outputTemperatureSensorRPMSensorVoltageSensorVoltageSensorAltitudeSensorAltitudeSensorS.BUS2 ToolBattery to 7/B+−It connects with the battery for power, etc.External voltage input cable of an option is used. The voltage of the battery can be displayed with a transmitter. with telemetryWhen using S.BUS, it is necessary to change CH mode into B or D.HUBUsage precaution󾛽WARNING󾛻 Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.󾛹 The R6308SBT receiver should be protected from vibra-tion by foam rubber, Velcro or similar mounting meth-ods.  Protect from moisture.󾛻 Keep away from conductive materials to avoid short cir-cuits.󾛻 Don't connect to Extra Voltage before turning on a receiv-er.Antenna installation precaution󾛻 Do not cut or bundle the receiver antenna wire.       󾛻 Do not bend the coaxial cable. It causes damage.󾛻 The antennas must be mounted in such a way to assure they are strain relieved.                                                                                󾛹 Keep the antenna as far away from the motor, ESC and other noise sources as you possibly can.󾛹 Be sure that the two antennas are placed at 90 degrees to each other.•TheR6308SBThastwoantennas.Inordertomaximizesignalreception and promote safe modeling Futaba has adopted a diversity antenna system.  This allows the receiver to obtain RF signals on both antennas and fly problem-free.Antenna installation for carbon fuselage󾛽WARNING󾛹 You must leave 30mm at the tip of the antenna fully ex-posed. The exposed antenna should be secured so that it cannot move around or back inside of your aircraft. (Typical installation)
Download:
Mirror Download [FCC.gov]
Document ID1700759
Application IDgVrrO8xwAaokxIeEJNPLLg==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize78.59kB (982380 bits)
Date Submitted2012-05-18 00:00:00
Date Available2012-05-18 00:00:00
Creation Date2012-02-02 14:36:01
Producing SoftwareAdobe PDF Library 9.9
Document Lastmod2012-05-09 13:33:32
Document TitleUser Manual
Document CreatorAdobe InDesign CS5_J (7.0.4)
FCC ID Filing: AZPR6308SBT-24G

Navigation menu