Contents
- 1. Users Manual part 1of4
- 2. Users Manual part 2of4
- 3. Users Manual part 3of4
- 4. Users Manual part 4of4
Users Manual part 3of4
Marine Mount
Instructions
WARNING
See the Important Safety and Product
Information guide in the GPS device
product box for product warnings and
other important information.
Garmin® strongly recommends having an
experienced installer with the proper
knowledge of electrical systems install the
device. Incorrectly wiring the power cable
can result in damage to the vehicle or the
battery and can cause bodily injury.
CAUTION
Always wear safety goggles, ear
protection, and a dust mask when drilling,
cutting, or sanding.
NOTICE
The metal contacts on the GPS device
and the mount should be kept dry to avoid
equipment damage. Use the weather cap
on the mount at all times when the unit is
not mounted to keep the metal contacts
dry and protected.
To obtain the best performance and to
avoid damage to your boat, install the
device according to these instructions.
Read all installation instructions before
proceeding with the installation. If you
experience difficulty during the installation,
contact Garmin Product Support.
Tools Needed
• Drill
• Phillips screwdriver
• 9.5 mm (3/8 in.) wrench or socket
• 3 bolts or 3 screws:
◦#8 (4 mm) pan-head machine bolts
with nuts and washers, and a
5 mm (1/16 in.) drill bit
◦#8 (4 mm) pan-head self-tapping
screws and a 1.5 mm (1/16 in.) drill
bit
Mounting Considerations
NOTICE
The swivel base must be mounted using
pan-head machine bolts or self-tapping
screws. Using screws with countersunk
heads can damage the mounting bracket.
DRAFT
A
ng an an
oper
ms install thems install the
he power cablehe power cable
the vehicle or thethe vehicle or the
se bodily injury.dily injury.
DR
DR
D
D
CAUTION
safety goggles, ear
safety goggles, e
a dust mask whea dust mask wh
D
D
CE
allall
ng with thng wi
ience difficulty d
ience diff
ntact ntact
Garmin Product
min Pr
Tools NeededTools Needed
• Drill• Drill
• Phillips scPhil
• 9.5 mm• 9.5 m
•3 b3b
The device should be mounted in a
location that provides a clear view of the
screen and is easy to reach.
The device should be mounted in a
location that is sturdy enough to support
the mount and device.
The device must be mounted in a location
that allows room to route and connect the
cables. You should allow at least 8 cm
(3 in.) of clearance behind the case.
Mounting the Bracket
Assembly
1Separate the swivel base ➀ from the
mount.
2Using the swivel base as a template,
mark the pilot hole locations ➁.
3Select an option:
• If you intend to secure the base
with machine bolts, drill three 5 mm
(5/32 in.) holes.
• If you intend to secure the base
with self-tapping screws, drill three
1.5 mm (1/16 in.) starter holes.
NOTE: Do not make the holes
deeper than half of the screw
length.
4Secure the swivel base with the bolts
or screws ➂.
5Place the swivel mount bracket ➃
over the swivel base and secure it with
the short knob ➄.
Installing the Mount on the
Mounting Bracket
1Align the slot ➀ on the back of the
cradle with the long mounting knob ➁,
2 Important Safety Information
DRAFT
e
se as a tempse as a tem
ations ations
swivel bswiv
ws ws
➂➂
..
and slide the cradle into place on the
bar.
NOTE: You can turn the long mounting
knob to adjust the width of the bracket
arms.
2Adjust the angle of the cradle, and
tighten the long mounting knob until
the cradle ➂ is secure.
3Rotate the swivel mount bracket ➃ to
an optimal viewing angle, and tighten
the knobs.
The bracket clicks as you turn it.
Connecting Power to the
Mount
1Select a mounting location based on
available power sources, safe cable
routing, and an unobstructed view.
2Connect the cables.
Important Safety Information 3
DRAFT
e cradle, ande cradle, an
ounting knob untilnting knob until
secure.secur
33
Rotate the swivRotat
an optimal van
the knobthe k
The bThe b
Con
M
Item Wire Color Wire Function
➀Red Power
➁Black Power
➂Yellow Serial data input
➃Blue Serial data output
➄Green Serial ground wire
➅Audio jack
3Insulate and secure unconnected
wires.
Installing the Device in the
Mount
NOTICE
Before you place the device in the mount,
ensure that the metal contacts on the
device and the mount are dry. Moisture on
the contacts causes equipment damage.
Use the weather cap to keep the mount
cradle dry.
1Place the weather cap ➀ in the
storage area on the mount.
2Place the bottom of your device into
the cradle ➁.
3Tilt the device back until it snaps into
place.
4 Important Safety Information
DRAFT
wire
A
A
RA
RA
RA
RA
nnectednnec
Device in theDevice in the
D
CE
ce in thce in th
2
Place the bottomace the
the cradle the cradle
➁➁
4Using the security screw tool, tighten
the security screw ➂ on the top of the
mount ➃.
Removing the Device from
the Mount
1Loosen the security screw.
2Press the button ➀ on the side of the
mount to release the device.
3Lift the device out of the mount.
4Place the weather cap ➁ on the
cradle.
Important Safety Information 5
DRAFT
om
rew.rew.
➀
on the side of theon the side of the
e the device.the device.
33
Lift the device oLift th
44
Place the wPla
cradle.cradle
DRAFT
DRAFT
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These
trademarks may not be used without the express permission of Garmin.
© 2011–2016 Garmin Ltd. or its subsidiaries
Printed in Taiwan
www.garmin.com/support
July 2016
190-02006-92_0A
DRAFT