GuangZhou Walkera Technology DEVO-F4 2.4GHz Transceiver User Manual DEVO F4

Download:
Mirror Download [FCC.gov]
Document ID	1915291
Application ID	xIIjh8DJqK+xzbQY/h6v9g==
Document Description	Users Manual Part 2of5
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	369.98kB (4624722 bits)
Date Submitted	2013-03-11 00:00:00
Date Available	2013-03-11 00:00:00
Creation Date	2013-02-28 17:55:46
Producing Software	pdfFactory Pro 4.50 (Windows XP Professional x86 Chinese)
Document Lastmod	2013-03-01 10:08:17
Document Title	~$DEVO-F4封底.pdf
Document Creator	pdfFactory Pro www.fineprint.cn
Document Author:	Administrator

Welcome to use the DEVO F4 transmitter CleUenlIOl'l
DEVD F4
(3) Tone:
The buzzer tone can be selected from 10 notes You can set the tone according to your preference and test
the performance.
Setting: Buzzer 7_4\/
With the "Status" item on, press DN to move the cursorato point to Tone Status On
item. Use R or L key to change the flashing value from 1 to 10.
Press EXT to exit after finished.
1.3 Vibrator
Throttle Stick
Active
—. Tone 1/10
The vibrator is used as an alarm function to remind the users.
Setting:
Press ENT to the Main Menu. Press UP or DN to move the cursorato point to System Menu, press ENT to
System Menu; Press UP or DN to move the cursorato point to Vibrator, press ENT to Vibrator setting interface.
There are two status as Inhibit and Active.
Press R or L to select Active or Inhibit.
Active means to start vibratioanhlblt
means to turn off vibration.
Press EXT to exit after finished.
1.4 Video Select
This function provides the settings of Inhibit or Active when choose the Video option.There are 8 channels
for your choice at the state of Active.
Setting:
Press ENT to the Main Menu. Press UP or DN to move the cursorato point to System Menu, press ENT to
System Menu; Press UP or DN to move the cursordto point to Video Select, press ENT to Video Select
setting interface.
Video Select . Video Select 7.4V
Press R or L to make the status to change
Active or Inhibit, Active means to start using. —v Status —v Status Active
Inhibit means to turn off. After Active, the
interface will be show channel selection.
Channel 1/8
Video Select 7.4V
‘ t Channels options: Press DN to move the cursor»to point to Channel item
S 3 us Active as shown in the above interface. Press R or L to make the Number change
between i to 8. With the 5.8G image transmmision module,1-8 channels
—v Channel could be choosed to receive the image signal.
1/8
Press EXT to exit after finished.
1.5 Stick Mode
There are 4 stick modes including Model Mode2, Mode3 and Mode4. Right-hand throttle includes Modei
and Mode3, while leftrhand throttle includes Mode2 and Mode4. See Below
Mode 2 and Mode 4 are listed in left-hand throttle.
M0052 MODE4
Throttle Elevator Throttle Elevator
Rudder4—I—> Aileron<—1—> Ailsron+ Rudder+
DEVD Fdi‘lE
oleUethion
—Welcome to use the DEVO F4 transmitter
DEVD F4
Mode 1 and Mode 3 are listed in right-hand throttle.
MODE1 MODE1!
Elevator Throttle Elevator Throttle
Rudder<—$—> Aileron<—i—> Aileron+ Rudder<—1—>
Setting: Press ENT to the Main Menu. Press UP or UN to move the cursorato point to System Menu. press
ENT to System Menu; Press UP or UN to move the cursordto point to _
Stick Mode, press ENT to Stick Mode setting interface. 5"“ M0“
There are mode «mode 2,mode 3 and mode 4 for options. Press UP or —' l> Made 1
DN to move the cursoreto point to desired item and then press ENT to Mode 2
confirm.
Press EXT to exit after finished. Mode 3
Mode 4
1.6 Stick Direction
Selling: Press ENTlo the Main Menu. Press UP or UN to move the cursorato point to System Menu. press
ENT to System Menu; Press UP or DN to move the cursordto paint to Stick Direction, press ENT to Stick
Direction setting interface.
Stick Direction 7.4V
Stick Direction: There are Elevator, Aileron, Throttle, Rudder for options.
Press UP or DN to move the cursorato point to the desired item. Press
Aileron Normal R or L to change the settings of corresponding sticks. There are Normal
Throttle Normal and Reverse. The default setting is Normal.
—. Elevator Normal
Rudder Normal
1.7 Stick Calibration
Setting: Press ENT to the Main Menu. Press UP or DN to move the Stick Calibra... 7.4V
cursorato point to System Menu, press ENT to System Menu; Press UP
or DN to move the cursor rto point to Stick Calibration, press ENT to Stick
Calibration setting interface. ENT ‘0 Calibrate
Stick Calibration. Mechanically move the right stick and left stick from their
minimum levels to their maximum levels several times, and then return
the sticks to the neutral positions, respectively.
Stick Calibra... . Stick Calibra... 7.4V
ENT to lesh ENT to Calibrate Press ENT againto stop the calibration
process and the display should show the
Calibration Success following interfacetCalibration Success).
The calibration has failed if press ENT and show the following interface. Please go back to the STMOD sub-
menu using EXT and restart the calibration process. Press EXT to exit after finished.
Stick Calibre...
ENT to Finish
Please Retry
DEVD F4 714
deUention
DEVD F4
Welcome to use the DEVO F4 transmitter
1.8 About
Setting: Press ENT to the Main Menu. Press UP or UN to move the
cursor -to point to System Menu, press ENT to System Menu; Press UP
or DN to move the cursorato point to About, press ENT to About setting
interface. Vou can check the current versions of hardware and software.
Press EXT to exit after finished.
2 Model Menu
Model Menu manages all the model data saved in DEVO F4. It includes Model Select, Model Name, Model
Copy, Model Transmit, Model Receive. Model Reset, Type Select, Trim System, Stick Position SWitch, Swash
Type, Power Amplitier, Fixed ID and Sensor setting.
2.1 Model Select
Setting: Press ENT to the Main Menu. Press UP or DN to move the
cursor»to point to Model Menu, press ENT to Model Menu; Press UP or —~ D 1 H Model 1
DN to move the cursor -to point to Model Select, press ENT to Model 2 H Model 2
Select setting interlaceThere are 15 ditferent model settings to be saved.
Press UP or DN to move the cursor rto point to select the model No you
want and press ENT to conlirm. Press EXT to exit.
Model Select 1 7.4V
3 H Model3
4 H Mode|4
5 H Mode|5
2.2 Model Name
In the menu of model name, you can make a desired name tor your model for long term storage. Its data
can be directly withdrawn in next flightsRepeat the step “2.1 Model Select" to choose the model you want
to name or save, press EXT to back to the intertace.
Setting: Press ENT to the Main Menu. Press UP or UN to move the
cursor -to point to Model Menu, press ENT to Model Menu, Press UP or
No. 1 UN to move the cursoreto point to Model Name, press ENT to Model Name
setting interface.
Press UP or DN to move the cursorato point to select the character and
figure which are needed to be changed. press R or L button to change the
character and tigure, and press UP or DN to set next one. Press EXT to
exit after finished.
Model Name
2.3 Model Copy
Setting, Press ENT to the Main Menu. Press UP or DN to move the cursorato point to Model Menu, press
ENT to Model Menu: Press UP or DN to move the cursorato point to Model Copy, press ENT to Model Copy
setting interface.
Model Copy 1 7.4V Model Copy 7.4V Press UP or UN to move the cursor»to
point to select the model you want to be
copied as source model and press ENT to
confirm, The serial No. and model name
2 H Model 2 [>1 H MOGBI 1 of Source Model will be shown as
3 H Model 3 _> 2 H Model 2 Illustration.
4 H Model4 3 H Model 3
Source Source: 1 H Model 1
—. D 1 H Modelt Desi
Model Copy 7.4V
Source: 1 H Model 1
Then press UP or DN to locate the source model, press ENT to confirm. Best: 2 H Model 2
Then an enquire "Are you sure?" is popped up as Illustration. Press ENT
to copy. or press EXT to exit.
Are you sure?
DEVCI F4715
deUention
DEVD F4
Weicome to use the DEVO F4 transmitter
2.4 Model wireless copy
The modei data between two DEVO F4 equipments can be wireiessly copied via Modei Transmit and Model
Receive in Model Menu.
(1) Model Transmit
Setting: Press ENT to the Main Menu. Press UP orDN to move the cursoralo _. D 1 H Model 1
point to Model Menu, press ENT to Modei Menu, Press UP or DN to move 2 H Model 2
the cursorato point to Model Transmission, press ENT lo Modei Transmission 3 H Model 3
setting interface. 4 H Model 4
5 H Mode|5
Model Transmit l7.4V
Press UP or DN to choose the source model which will be transmitted. and press ENT to confirm, an enquiry
information “Are you sure?" Wiil be shown as below liiustration. Press ENT to confirm and EXT to exit.
Model Transmit 17.4v Model Transmit £7.4v
No. 1 N0- 1 Press ENT to transmit, “Transmitting
Model 1 Model 1 ...... "appears in the interface. Or press
_ ENT to confirm. Press EXT to exit after
Are you sure? Transmitting... another DEVO F4 received the data.
>>>>>>>>>>
(2) Model Receive
Press ENT to the Main Menu. Press UP or DN to move the cursoreto point to Model Menu, press ENT to
Model Menu; Press UP or DN to move the cursordto point to Modei Receive, press ENT lo Mcdei Receive
setting interface. An enquiry information “Are you sure?" Will be shown as below liiustration.
Modei Receive . Modei Receive
Receive Config Receive Config Press ENT to receive, “Connecting .
and “Receiving ...... " Will be shown in series
Are you sure? Connecting... in the interface.
>>>>>>>>>>
After Model received the data Wiii enter to the Model save interface. Press UP or UN to move to the cursorato
point to Model data save position. Press ,
ENT will pop up “Are you sure". Press ENT Model Receive ”AV
to save, press EXT to cancel. —. D 1 H Model 1
Press ENT to confirm and EXT to exit. 2 H Model 1
3 H Model 3
Model Receive 17.4V
No. 3
Model 3
4 H Model 4 Are you sure?
5 H Model 5
2.5 Model Reset
Using the Mcdei Reset function the settings for one or all models can be reset to the factory defaults.
Setting: Press ENT to the Main Menu. Press UP or DN to move the cursorato point to Model Menu, press ENT
to Model Menu; Press UP or DN to move the cursordto point to Modei Reset, press ENT again to display to
modei selection. Use R and L to seiect “ALL" for ali models or the individual model name for a single model reset.
Model Reset Model Reset
Model All Press UP or UN to move the cursor4 to
No- 1 point to the desired model No and press
Model 1 ENT, an inquiry “Are you sure" Will be shown
2 H M‘Jde‘ 1 as Illustration.
3 H Modei 3 Are you sure? Press ENT to reset and EXT to cancel.
4 H Modei 4 Press EXT after finished.
—v>’i HModeH
DEVE} F4 *1 B
oleUenjtion
DEVD F4
Welcome to use the DEVO F4 transmitter
2.6 Type Select
This transmitter offers a choice of two model types. The options are helicopter and airplane.
Press ENT to the Main Menu. Press UP or DN to move the cursoreto point
to Model Menu, press ENT to Model Menu; Press UP or DN to move the
cursorato point to Type Select, press ENT to Type Select setting interlace. _. p Helicopter
Model Transmit 7.4V
Press UP or DN to move the cursorato point to helicopter or Airplane option. Airplane
Press ENT, there is an inquiry shows. Press ENT to select the desired
model. If the default model are the desired one. Press ENT and press EXT
to exit.
2.7 Trim System
Trim System is able to finely tune the following terms, respectively: Elevator, Aileron, Rudder, Throttle. The
trim range is divided into 20 grades. (factory default is set at 4). It is convenient to subtly modify the pitch by
adlusting the trim range.
Trim System 1'7"“, Press ENT to the Main Menu. Press UP or DN to move the cursorato point
Elevator —. 4/20 to Model Menu, press ENT to Model Menu, Press UP or DN to move the
Normai cursorato point to Trim System, press ENT to Trim System setting interface.
Aileron 4/20
Normal
Rudder 4/20
Normal
Press UP or DN to move the cursorato point to the item that need to adjust.
Press R+ or L- can change the setup, Maxium is 20.
For elevator, aileron and rudder, there are two more options ' Normal and Limited. "Normal" means the trim
is always working although the corresponding
stick stays anywhere. “Limited" means the Tm“ System W'AV Tm" System ”AV
trim is out ofworking when the corresponding Elevator 4/20 Elevator 4/20
stick is at maximum position. -> Normal - Limited
Press EXT to Bxll after finished. New“ 4/20 Allen)" 4/20
Normal Normal
Rudder 4/20 Rudder 4/20
2.3 Stick Position Switch Normal Normal
According to the lollowmg setting, the stick can be used as a swttch. The turn-on orturn-ofl position at which
stick stays can also be settable.
Method for setting:
Press ENT to the Main Menu. Press UP or DN to move the cursorato point to Model Menu, press ENT to
Model Menu; Press UP or UN to move the cursorato point to Stick Position Switch, press ENT to Stick Position
SWitch setting interface.
There are four options under the Stick
position switch: SPSO, SPSl, SPSZ, SPSB.
_, SWitch SPSO SW Switch SPSO SW Press UP or DN to move the cursorato
point to SWitch option. Press R or L to choose
the sWitch you want to deline.
Position 0 Press UP or DN to move the cursordto
On Up point to the channel option. There are Inhibit
and channel options.(Default setting inhibit)
Stick Positio... 7.4V Stick Positio... 7.4V
Channel Inhibit —' Channel Elevator
The channel includes four items: Elevator, Aileron, Throttle and Rudder. The factory default is inhibit. Take
Elevator for example.
Press R or L to choose the Elevator as stick,
and then press DN to move the cursordto
point to value ol position. It's possible to SWitch SPSO SW Switch SPSO SW
adjust the stick position via pressing R or L.
Press UP or DN to move the cursoreto point
to On option. And then press R+ or L- to
change the ON status of stick postion On Up —' On Up
Press EXT after finished.
Stick Positio... 7.4V Stick Positio... 7.4V
Channel Elevator Channel Elevator
—~ Position 0 Position 0
DEVD F4717
oleUeniion
Welcome to use the DEVO F4 transmitter
DEVEI F4
2.9 Swash Type
Only one Swash Type: 1 Servo Normal. Swash Type 7.4V
Press ENT to the Main Menu. Press UP or DN to move the cursorato point
to Model Menu, press ENT to Model Menu: Press UP or UN to move the —~ D 1 Servo Normal
cursorato point to Swash Type, press ENT to Swash Type setting interface.
Press EXT to exit after finishing.
2.1 a Power Amplifier
The transmission output power of DEVO F4 is adyustable. It is divided into six grades from low to high. The
lower the transmission output power transmits. the shorter the radio range is. and the longer the stand-by
time will be, the higher the transmission output power, the farer the radio range, and the shorter the stand
by time. Choose the appropriate transmission output power according to the actual situation
Press ENT to the Main Menu. Press UP or DN to move the cursoreto point to Model Menu, press ENT to
Model Menu; Press UP or DN to move the cursorato point to Power Amplifier, press ENT to Power Amplifier
setting interface.
PowerAmplifier . 00 00 O‘I H?
Press UP or DN to move the cursordto
point to the desired output power value and
15 dBm press ENT to oontirm. The output power
level Will also show on the main menu
10 dBm
interface see the left Illustration:
-> D ZOdBm
output power level
2.11 Fixed ID
Using the Fixed ID function allows users to create a unique relationship between transmitter model data and
the corresponding model‘s receiver. It significantly speeds up the binding process and also prevents mistakenly
flying an aircraft With the incorrect transmitter model selected.
(1) Fixed ID setup
To start the Fixed ID setup it is important that the transmitter and receiver have successfully completed automatic
ID binding process. Once the transmitter and receiver are paired a Fixed ID can be set as described below:
Press ENT to the Main Menu. Press UP FIXSCI ”3 . FIXED! ID
or UN to move the cursorato point to _. St t 0
Model Menu. press ENT to Model Menu, _' Status 0" a “5 n
Press UP or DN to move the cursorato
point to Fixed ID. press ENT to the Fixed
ID setting interface.
ID Code 228600
Press R+ or I.- to set Status 0N. and there is a Random Fixed ID display on the screen. Press DN to move
the cursor a to point to ID Code, press ENT to move the cursor a to point to the first code of the Fixed ID.
Press R+ or L- to change the Code; Press UN to move to next Code. Press ENT after finished setting, there
is an indury “Are you sure’? Press ENT to confirm and execute the binding process. After finished binding
the display Will return to the Model Menu automatically.
Fixed ID . Fixed ID . Fixed ID
Status On Status On Status On
ID Code 228600 IDCode 228600 'DCode 228600
Matching...
>>>>
Are you sure?
DEVD F4718
oleUenIion
DEVD F4
Welcome to use the DEVO F4 transmitter
(2) Fixed ID Cancellation
ID code clearance key
Before the receiver electrify, press and ctrl the ID clear button, add a 5V
Power source to other input terminal, if the Red indicator is tWinkle slowly
which means cleared ID memory already, then, Loosen the ID clear button.
Fixed ID
—r Status On
Refer to the instructions of Fixed ID setting
ID Code 228600 above to the following interface. Press UP
to move the cursor a to point to Status ON.
When Fixed ID Status ON, press R+ or L-
to change ON to OFF. Press EXT to exit.
2.12 Sensor Setting
Setting method: Press ENT to the Main Menu. Press UP or DN to move the cursoreto point to Model Menu,
press ENT to Model Menu; Press UP or UN to move the cursorato point to Sensor Setting. press ENT to
Sensor setting interface.
Press R or L to select Activate or Inhibit (the default setting is Inhibit), such Sensor Setting 7-4V
as press Activate will includes No Signal Warning, Voltage sensor,
Temperature sensor, GPS receiver setting etc. —. Status Inh‘b"
Sensor Setting 7.4V
Status Active
—» No Signal inhibit (1) No Signal
Voltage Press UP or DN to move the cursor -to point to No Signal option. Press R
Temperature or L to choose Inhibit or Active (default setting is inhibit). If you choose
GPS Setting Active, the Radio will alarm when telemetry signal lost. see the left Illustration:
(2) Voltage
There are 3 different types of voltage can be measured. It includes Internal 5V, External V1 and V2 which
can be monitored two different external voltage(i.e. battery) respectively. Once the measured voltage is lower
than the setting value, the Radio will alarm.
(2.1) Receiver 5V(Internal) PFV(Power Feeding Voltage) Alarmed value can be setted as 3.5-6V
Voltage setting: press DN to move the cursordto point to Voltage otpion on the Sensor setting interface. Then
press ENT to enter the voltage setting interface. Press UP or DN to move the cursorato point to Int.5V option.
Press R or L to activate the 5V, the alarm interface Will appear in the interface, please refer to the illustration.
Voltage 7.4V Voltage 7.4V Voltage 7.4V
Int. 5V Int. 5V
—~ Active Int. 5V Active
3.6V —> 3.6V
Inl'ilbll EXI- V1 Inhibit E“ VI Inhibit
—> Inhibit
Ext. V1
Ext. v2 Inhibit Ext. v2 mm," Ext V2 Inhibit
Press UP or DN to select the Alarm Voltage setting option, press R or L to set the value. The range is 3.6-
6V. You can continue to set other items afler you finished.
(2.2)V1 External Vt
Press UP or DN to move the cursorato point to External V1 setting option. Press R or L to activate the V1,
the details refers to the illustration.
Voltage 7.4V Voltage 7.4V
Press UP or UN to move the cursor >to Int. 5V _ Int. 5V _
point to the Alarm Voltage setting. Press ”mm“ "mm"
R or I. to set the value. The setting range Ext. Vi _. Active E)“ V1 Active
is 0.2~99.9V. You can continue to set other 0.2V _. 0.2V
items after you finished. Ext. V2 Ext. V2
Inhibit Inhibit
DEVD F4719
oleUethion
Welcome to use the DEVO F4 transmitter
DEVE} F4
(2.3) External: V2 setting can refer to External V1 setting. Press EXT to back to sensor setting Interface to
set other options.
(3) Temperature sensor
The temperature sensor can measure up to 4 different temperature(i.e.motors). Vou can choose Celsius or
Fahrenheit. The alarmed value can be setted to 4 different temperature. Once the measured value is higher
than the setting value, the radio will alarm. The Alarm Temperature value can be setted as -20~220‘C or
-4.0~428.0’ F.
Temperature Settingzln the Sensor Setting interface, press UP or DN to Temperature ”AV
move the cursor»to point to Temperature Sensor setting option, and press Unit _. Celsius
ENT to Temperature setting interface. See the right Illustration.
(3.1) Unit Temp- Ti Inhibit
Press UP or DN to move the cursorato point to Unit setting option, and
press R or L to choose Unit, two kinds of Unit:Celsius and Fahrenheit. Temp- 72 Inhibit
(3.2) Alarm Temperature settings
Press UP or DN to move the cursorato point to T1 option, Press R or L to activate the setting. Inhibit will
change to Active and Alarm temperature will be shown. It you choose Inhibit, the Alarm temperature value
won t be shown.
Temperature 17.4V Temperature t7.4V
Press UP or DN to move the cursorato
point to Alarm setting, press R or L to set
the alarm temperature value. Press UP or
SAME Temp- T1 Ame DN to set other items after finishing the
100 —~100 setting.
inhibit Temp- 72
Unit Unit
Celsius CeISius
Temp. T1
Tem . T2 .
F Will)" T2,T3,T4 setting. Refer to the step of “T1".
(4) GPS Setting
There are 4 items including Altitude Type, Speed Unit, Date Type and Time Zone in the GPS receiver setting
interface.
Setting Press ENT to the Main Menu. Press UP or DN to move the GPS Setting 7'4V
cursorato point to Model Menu, press ENT to Model Menu, Press UP or —> High Type Absolute
DN to move the cursorato point to Sensor Setting, press ENT to Sensor Speed Unit Knots
setting interface, Press UP or UN to move the cursorato paint to GPS
Setting, press ENT to GPS setting interface.
(4.1) High Type
Press UP or DN to select the High type on the GPS setting intertaoe and
there are Absolute and Relative two type.
Date Type DD-MM-W
Time Zone UTC 03:00
GPS Setting 7.4V GPS Setting 7.4V
—> High Type Absolute High Type Absolute (4'2) Speed Unit
. Press UP or UN to select the Speed Unit
Spee" ”n" Km‘s T 39”“ ”n" ““5 on the GPs setting interface and it includes
Date Type DD’MM’W Date Type DD’MM’YV knots and kah and relative. Select the
Time Zone UTC 08 00 Time Zone UTC 08:00 desired item.
(4.3) Date Type
Press UP or UN to select the Date Type on the GPS setting interface and it includes DD-MM-YY, MM-DD-
VY and VYVMMeDD. Select the desired item.
GPS Setting 7.4V GPS Setting 7.4V
High Type Absolute High Type Absolute
Speed Unit Knots Speed Unit Knots (4-4) Time Zone .
Press UP or DN to select the Time Zone.
press R or L to set the desired Time Zone.
_. Date Type DD-MM-YY Date Type DD-MM-YY
Time Zone UTC 08 00 —. Time Zone UTC 08:00
DEVD F4720
oleUention
DEVD F4
3.0 Funct on Menu
The Function Menu allows you to customize the settings for your saved models. This menu includes the
following: Channel Reverse Switch, Travel Adjust. Sub Trim. Dual Rate and Exponential, Throttle Curve,
Program Mix, Monitor, Fail Safe, Sensor View, Trainer and Timer. Total 11 settings.
Welcome to use the DEVO F4 transmitter
3.1 Reverse Switch
Press ENT to the Main Menu. Press UP or DN to move the cursor»to point to Function Menu. press ENT
to Function Menu: Press UP or DN to move the cursordto point to Reverse Switch, press ENT to Reverse
Switch setting interface.
R S 't h 7.4V
Press UP or DN to move the cursorato point to ELEV(take Elevator for everse M C
example), Press R or L to shift the status between nomal and reverse. These —~ Elevator Normal
are two status for option. And the default setting is Normal. All Channels
Reverse Switch like: Aileron. Throttle. Rudder can be referred to the way
olr ELEV Reverse SWitch. And press EXT to exit after setting finished. Throttle Normal
Rudder Normal
Aileron Normal
3.2 Travel Adjust
Press ENT to the Main Menu. Press UP or DN to move the cursor -to point to Function Menu, press ENT
to Function Menu; Press UP or DN to move the cursorato point to Travel Adjust, press ENT to Travel Adjust
setting interface. The interface display a channel's servo travel value status.
Travel Adjust l7.4V Travel Adjust 07.4V
Elevator Elevator Press UP or DN to move the cursordto
" U100.0 U100 0 pointto “Elevator's U" setting (ELEV is used
_ 0100-0 _ " D1000 in the example), press R+ or L- key, can
Aileron HUD-0 Aileron UGO-0 set the travel value while the Elevator
R1000 R1000 towards up . The adjustment range one
Throttle H1000 Throttle H100 0 150.0%. Factory default setting :1oo.o%.
L100.0 L100.0
Press UP or DN to move the cursorato point to “Elevator's D" setting, press R+ or L- key, can set the travel
value while the Elevator towards down. The adjustment range 0.071500%. Factory default setting 100.0%.
The settings for all channels, Aileron, Throttle. Rudder can all be set using this process.
Press EXT to exit.
3.3 Sub Trim
NOTE: Sub Trim is used to fine tune the servo neutral position during setup. In order to avoid pushing the
servo beyond its limits and possibly causmg damage it is advised to first mechanically adjust the servo arm/bell
crank to be as close to the neutral point as possible. Only when this is
complete may sub trim be used to make a final adjustment. Sub Trim
—~ Elevator
Press ENT to the Main Menu. Press UP or DN to move the cursorato point
to Function Menu, press ENT to Function Menu; Press UP or DN to move
the cursoreto point to Sub Trim, press ENT to Sub Trim setting interface. Throttle
Rudder
Ailerori
The interface display a adjustable channel's name and adjustable data project. Press R+ or L- can adjust
the fine tune the servo neutral position. Press UP or DN can select the channel you wish to set. Every Channel
default setting value is 0.0%. The adjustment ranges are as below:
Channelname A- A . .A A _ A ., a ,a
Elevator D62.5%~U62.5% Throttle L62.5%~H62.5%
Aileron R62.5%~L52.5% Rudder R62.5%~L62.5%
Press EXT to exit.
DEVD F4’2’I
(JeUention
DEVD F4
Welcome to use the DEVO F4 transmitter
3.4 Dual Rate and Exponential
This functlon can be setting the amount of actlon tor Elevator, Alleron, Tall Servo. The setting range is
0-125%. It can assist and adjust to N Wlth Exponent Curve and varlous settlngs.
Press ENT to the Maln Menu. Press UP or UN to move the cursordto point
to Functlon Menu, press ENT to Function Menu; Press UP or DN to move
Dual Rate and... l7.4V
the cursordto point to Dual Rate and Exponential, press ENT to Dual Rate P05 '3
and Exponenllal selling interface. —. Channel Elevator
(1) Channel Position Pos 0
Press UP or DN to move the cursorato polnt to Channel setting, press R+
or L key, can set the Channel as follows - ELEV, AILE and RUDD ect. Dual Rate 100
Dual Rate and... £7.4V (2) Position
Pos 0
Channel Elevator Press UP or DN to move the cursorato polnt to Posltion setting item, with
“Pos 0, Pos 1" two potions. For example, the “Elevator" of ”Channel". if
select the “Pos 0" which means the settlng parameter of “Pos 0”. If select
Dual Rate 100 "Pos 1" which means the setting parameter of P03 1.
- Posltion Pos 0
(3) Dual Rate
Press UP or DN to move the cursorato point to Dual Rate settlng, press R+ or L- key, can set the “Position"
dual rate value. The default setting is 100%.
Dual Rate and... £7.4V Dual Rate and... l7.4V
Pos 0 Pos 0
Channel Positlon Press UP or DN to move the cursor to
Elevator Pos 0 polnt to Exponential setting, press R+ or L-
POSltion Pos 0 Dual Rate key, can set the ‘Position" Exponential
‘lOO value . there are i100% and LINE three
settlngs avallable.
(4) Exponentlal
—~ Dual Rate —~ Exponential
100 Line
Press EXT to exlt.
3.5 Throttle Curve
Throttle cure ls adopt 7 points adlustment.
Press ENT to the Main Menu. Press UP or DN to move the cursorato polnt to Functlon Menu, press ENT
to Functlon Menu; Press UP or UN to move the cursorato polnt to Throttle Curve, press ENT to Throttle
Curve setting lnterface. see below lllustratlon.
Throttle Cun/e 7.4V Throttle Curve
—> Positlon The interface of Throttle Curve will pop up
“All servos Hold?" inquire. if you choose
“OK" every servo Wlll hold at current posltion,
—~ OK Point lf you choose ‘Cancel" every servo won't
Cancel be hold.
In. 0.0
All Sen/o5 Hold? Exponential
(1) Position
Press UP or DN to move the cursorato polnt to Posltion settlng item, with “Pos 0, Pos 1" two potlons. If select
the ‘ Pos 0" which means ordered curve parameters of “Pos 0". Also, select “Pos ‘l" is the same means.
Throttle Curve $7.4V
(2) Exponential curve setting Position
Press UP or DN to move the cursor rto point to “Exponentlal” setting. Press P05 0
R or L can set ON and OFF. The throttle curve will being changed smoothly
lf select 0N. Select OFF lf not need then the throttle curve Wlll be shown Point
as a llne. see the right lllustratlon:
a Exponentlal
Off
(3) Curve settlng. Including “Point" and “Output" Irl: 0.0
DEVD F4 722
oleUention
DEVO F4
Welcome to use the DEVO F4 transmitter
(3.1) Point setting
Press UP or DN In Throttle Curve interface to select Points setting. Press
Throttle Curve
R+ to expand a list including seven points: ‘Point-L".“Point-1".“Point-2", Position
“Point-M". “Point-3". "Point-4" and "Point-H". Exponenfial
(3.2) Status setting _. Pmm
After above setup. press DN to select Status setting. press R+ or L- to set
Inhibit or Active. Select Inhibit if keeping the current value (the default In: 0-0
setting is Inhibit). Select Active for changing the above points’ value.
Note: After select Point L or Point H . the status setting won't be display.
Throttle Curve 17.4V Throttle Curve 17.4V Throttle Curve
Point Point -M Point Point -M —~ Point
St t St t
_' “'5 Inhibit _' “'5 Active
Output Output
50.0
Out: 0.0 In: 0.0 Out: 0.0 In: 0.0
(3.3) Output setting Throttle Curve
There is a expand item “Output" after select Status Active. press DN to Point
select Output setting. press R+ or L- to increase or decrease. respectively.
the output value. The adiustable range is from 0.0% to 100.0%. ‘IN" and Status
“Out" means throttle stick input and output level. _. Output
Press EXT to exit.
3.6 Program Mix ”120.0
There are 8 series of program mix, mix channels and values are adJustable.
Press ENT to the Main Menu. Press UP or DN to move the cursor -to point
to Function Menu. press ENT to Function Menu; Press UP or DN to move
the cursordto point to Program, press ENT to Program setting interface. Program Mix 1
see the right Illustration
And press ENT to program mix setting and current status (default setting
is “inhibit”) interface. Press R+ or L7 to choose Inhibit, normal or curve. Normal
Take “program mix 1" for example, there are “normal" and “curve" setting. Curve
Program Mix
—. D Inhibit
(1) The “normal" setting of “program mix"
Press UP or DN to move the cursordto point to the ”Normal"setting. Press ENT button then pop up ”All Servos
Hold?" Press R or I. to choose OK orCancel.
If ‘0K" selected, all the servos will be locked Program “I“ 1‘ 74" ng'am Mix 1 ”AV
in the current status. if “Cancel" selected.
all servos are unlocked. Press ENT enter All Servos Hold? _' Master Elevator
to Program Mix 1 setting interface. _' OK Slave Elevator
Cancel Up 0
(1.1) Master channel setting
Press UP or DN to move the cursorato point to Master Channel setting. press ENT to the Master Channel
setting interface. Press UP or UN to move the cursorato point to the desired Master Channel. press ENT to
confirm and press EXT to be back to Program Mix 1 interface.
(1.2) Slave channel setting:
Press UP or DN to move the cursorato
—~ D Elevator d D Elevator point to Slave Channel setting. press ENT
Aileron Aileron to the Slave Channel setting interface. Press
UP or DN to move the cursorato point to
Throttle the desired Slave Channel. press ENT to
Rudder confirm and press EXT to be back to
Program Mix 1 interface.
Master Slave
Throttle
Rudder
9 Elevator
DEVD F4723
oleUention
DEVE} F4
Welcome to use the DEVO F4 transmitter
(1.3) Gain setting: Take Elevator at Master as an example.
(1.3.1) UP
Mix amount selling when elevator stick moved upward. Press UP or DN to move the cursorato point to Up
setting. Press R or L to increase or decrease the mix amount separately. It is possible to reverse mix direction
through changing the “+" or “-" sign before amount. The adjustable range is t125%.
(1.3.2) Down
Mix amount setting when elevator stick moved downward. Press UP or DN to move the cursorato point to
Down setting. Press R or L to increase or decrease the mix amount separately. It is possible to reverse mix
direction through changing the “+" or , sign before amount. The adjustable range is :125%.
(1.3.3) Offset Setting
This function can make Slave begin to mix through the corresponding Lever switch from a certain point as
the starting point.
Press UP or DN to move the cursoreto point to Offset setting. Press R+ to increase the mix amount and
press L7 to decrease. It is possible to reverse Offset direction by pressing R or L button to change the "+" or
“-" sign before amount. The adjustable range is :100%.
Program Mix 1 H7.4V Program Mix 1 117.4V
Program Mix1 117.4V
—>UP
UP 0
Down 0
Offset 0
(1.3.1) up
(1.4) SWitch
Press UP or DN to move the cursorato Program MW
point to the Switch setting item and press
ENT to enter the select interface of SWitch.
Press UP or DN to choose the switch you Offset
wish to set. Press ENT to confirm.
Press EXT to be back to Program Mix 1
interface.
Notes: Enable the Stick Switch at “2.8 Stick Position Switch" setting item.
(1 3.3) Offset Setting
Switch
—' D Always On
SPSO SW
SPS1 SW
SPSZ SW
SPSB SW
Down
-' Switch
(2) Curve setting of Program Mix
Press UP or DN to move the cursor ’to point to the “Curve“ setting, Press ENT button then pop up “All Servos
Hold?" Press R or L to choose 0K orCancel.
ll "OK" selected, all the servos Wlll be locked Program Mix 1 7-4V Program Mix 1 ”AV
in the current status, if "Cancel" selected, _, Master Elevator
all servos are unlocked. Press ENT enter All Servos Hold?
to Program Mix 1 setting interface. OK Slave Elevator
“ Exponential Off
Cancel
(2.1) Master channel setting I”: 0 Out: 0
Press UP or UN to move the cursorato point to Master Channel setting, press ENT to the Master Channel
setting interface. Press UP or DN to move the cursordto point to the desired Master Channel, press ENT to
confirm and press EXT to be back to Program Mix 1 interface.
(2.2) Slave channel setting:
Press UP or DN to move the cursorato
—> D Elevator _, D Elevator point to Stave Channel setting, press ENT
to the Slave Channel setting interface. Press
Throttle UP or DN to move the cursorato point to
Throttle the desired Slave Channel, press ENT to
Rudder Rudder confirm and press EXT to be back to
éElevator Program Mix 1 interface.
Master Slave
Aileron Aileron
DEVD F47 24

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-702
Create Date                     : 2013:02:28 17:55:46+08:00
Creator Tool                    : pdfFactory Pro www.fineprint.cn
Modify Date                     : 2013:03:01 10:08:17+08:00
Metadata Date                   : 2013:03:01 10:08:17+08:00
Format                          : application/pdf
Creator                         : Administrator
Title                           : ~$DEVO-F4封底.pdf
Producer                        : pdfFactory Pro 4.50 (Windows XP Professional x86 Chinese)
Document ID                     : uuid:d5130ff4-11e8-4b99-b247-86e24c59501f
Instance ID                     : uuid:49ed9c26-d295-4df7-aad6-f218ef7a5159
Has XFA                         : No
Page Count                      : 12
Page Layout                     : SinglePage
Author                          : Administrator

EXIF Metadata provided by EXIF.tools