GuangZhou Walkera Technology DEVO-F4 2.4GHz Transceiver User Manual DEVO F4

GuangZhou Walkera Technology Co., Ltd 2.4GHz Transceiver DEVO F4

Users Manual Part 4of5

Download: GuangZhou Walkera Technology DEVO-F4 2.4GHz Transceiver User Manual   DEVO F4
Mirror Download [FCC.gov]GuangZhou Walkera Technology DEVO-F4 2.4GHz Transceiver User Manual   DEVO F4
Document ID1915293
Application IDxIIjh8DJqK+xzbQY/h6v9g==
Document DescriptionUsers Manual Part 4of5
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize337.78kB (4222242 bits)
Date Submitted2013-03-11 00:00:00
Date Available2013-03-11 00:00:00
Creation Date2013-02-28 17:55:46
Producing SoftwarepdfFactory Pro 4.50 (Windows XP Professional x86 Chinese)
Document Lastmod2013-03-01 10:17:35
Document Title~$DEVO-F4封底.pdf
Document CreatorpdfFactory Pro www.fineprint.cn
Document Author: Administrator

oIeUenIion
DEVD F4
Welcome to use the DEVO F4 transmitter
2.11 Fixed ID
Using the Fixed ID function allows users to create a unique relationship between transmitter model data and
the corresponding model's receiver. It significantly speeds up the binding process and also prevents mistakenly
flying an aircraft with the incorrect transmitter model selected.
(1) Fixed ID setup
To start the Fixed ID setup it is important that the transmitter and receiver have successfully completed automatic
ID binding process. Onee the transmitter and reoeiver are paired a Fixed ID can be set as described below‘
Press ENT to the Main Menu. Press UP or
DN to move the cursoreto point to Model F'Xed ID
Menu, press ENT to Model Menu; Press UP Off —. Status On
or DN to move the CUVSOI‘WD point to Fixed
ID, press ENT tothe Fixed ID setting interface. ID Code 228600
Press R+ or I.- to set Status ON, and there
is a Random Fixed ID display on the screen.
Press DN to move the cursor » to point to
ID Code, press ENT to move the cursor - to point to the first code of the Fixed ID.
Press R+ or L- to change the Code; Press DN to move to next Code. Press ENT after finished setting, there
is an inqury “Are you sure? ”. Press ENT to confirm and execute the binding process. After finished binding
the display will return to the Model Menu automatically.
Fixed ID . Fixed ID . Fixed ID
Status On Status On Status On
ID Code 228600 IDCode 228600 “30068 228600
Matching...
>>>>
Are you sure?
(2) Fixed ID Cancellation
Before the receiver electrify, press and ctrI the ID clear button, add
a 5V Power source to other input terminal, if the Red indicator is
twinkle slowly which means cleared ID memery already, then, Loosen
the ID clear button.
ID code clearance Key
Fixed ID . Fixed ID
—' Status 0" -‘ Status 0ft Refer to the instructions of Fixed ID setting
above to the folloWlng interface. Press UP
to move the cursor a to point to Status 0N.
When Fixed ID Status 0N, press R+ or L-
to change ON to OFF. Press EXT to exit.
ID Code 228600
2.12 Sensor Setting
Setting method: Press ENT to the Main Menu. Press UP or DN to move the cursorato point to Model Menu,
press ENT to Model Menu, Press UP or DN to move the cursorato point to Sensor Setting, press ENT to
Sensor setting interface.
Press R or L to select Activate or Inhibit (the default setting is Inhibit). such Sensor Setting 7-4V
as press Activate will includes No Signal Warning, Voltage sensor,
Temperature sensor. GPS receiver setting etc. A Status Inh'b“
Sensor Setting 7.4V
Status Active
—> No signal Inhibit (1) No Signal
Voltage Press UP or DN to move the cursor -to point to No Signal option. Press R
Temperature or L to choose Inhibit or Active (default setting is inhibit ). It you choose
GPS Setting Active. the Radio Will alarm when telemetry signal lost. See the left Illustration:
DEVD F4737
oleUethion
DEVI] F4
Welcome to use the DEVO F4 transmitter
(2) Voltage
There are 3 different types of voltage can be measured. It includes Internal 5V, External V1 and V2 which
can be monitored two different external voltage(i.e. battery) respectively. Once the measured voltage is lower
than the setting value, the Radio will alarm.
(2.1) Receiver 5V(Internal) PFV(Power Feeding Voltage) Alarmed value can be setted as 3.6-6V
Voltage setting: press DN to move the cursorato point to Voltage otpion on the Sensor setting interface. Then
press ENT to enter the voltage setting interface. Press UP or DN to move the cursor >to point to lnt.5V option.
Press R or L to activate the 5V, the alarm interface Will appear in the interface, please refer to the illustration.
Voltage 7.4V
'"l- 5V _. Inhibit
E)“- V1 Inhibit
EXI- V2 Inhibit
Press UP or DN to select the Alarm Voltage setting option, press R or L to set the value. The range is 3.6-
6V. You can continue to set other items after you finished.
(2.2) V1 External V1
Press UP or UN to move the cursorato point to External V1 setting option. Press R or L to activate the V1,
the details refers to the illustration.
Press UP or DN to move the cursorato Voltage 7-4V Voltage 7-4V
point to the Alarm Voltage setting. Press Int. 5V . lnI. 5V ,
R or L to set the value. The setting range lnhm" ”mm“
is D.2~99.9V. You can continue to set other Ext. V1 _. Active Ext. V1 Active
items after you finished. 0.2V —~ 0.2V
(2.3) External: V2 setting can referto External EXL V2 Inhibit 5‘" V2 Inhibit
V1 setting. Press EXT to back to sensor
setting interface to set other options.
(3) Temperature sensor
The temperature sensor can measure up to 4 different temperature(i.e.motors). You can choose Celsius or
Fahrenheit. The alarmed value can be setted to 4 different temperature. Once the measured value is higher
than the setting value, the radio will alarm. The Alarm Temperature value can be setted as -20~220°C or
-4.0~428.0’ F.
T I 7.4V
Temperature Setting: In the Sensor Setting interface, press UP or UN to empera ure 1
move the cursordto point to Temperature Sensor setting option. and press Unit _. Celsius
ENT to Temperature setting interface. See the illustration.
(3.1) Unit Temp' T1 ”WW
Press UP or UN to move the cursorato point to Unit setting option, and
press R or I. to choose Unit, two kinds of Unit: Celsius and Fahrenheit.
Temp. T2 Inhibit
(3.2) Alarm Temperature settings
Press UP or DN to move the cursorato point to T1 option, Press R or L to activate the setting Inhibit Will change
to Active and Alarm temperature will be shown. If you choose Inhibit, the Alarm temperature value won t be shown.
Temperalure £7.4V Temperalure 17-4V Press UP or DN to move the cursorato
Unit point to Alarm setting, press R or L to set
the alarm temperature value. Press UP or
—. Acm Temp T1 Acm DN to set other items after finishing the
100 -’100 setting.
Inhibit Temp 72
Unit
Celsius Celsius
Temp. T1
Temp. T2 .
'"h‘b" T2,T3,T4 setting: Refer to the step oi“T1'.
DEVD F4 38
oleUenlion
DEVD F4
Welcome to use the DEVO F4 transmitter
(4) GPS Setting
There are 4 items including Altitude Type, Speed Unit, Date Type and Time Zone in the GPS receiver setting interface.
Setting. Press ENT to the Main Menu. Press UP or UN to move the cursorato
point to Model Menu, press ENT to Model Menu; Press UP or UN to move GF'S Setting 7-4V
the cursorato point to Sensor Setting, press ENT to Sensor setting interface;
Press UP or UN to move the cursor rto point to GPS Setting. press ENT
to GPS setting interface.
(4.1) High Type
—r High Type Absolute
Speed Unit Knots
Date Type DD-MM-YY
Press UP or DN to select the High type on the GPS setting interface and there Time Zone UTC 08:00
are Absolute and Relative two type.
GPS Setting 7.4V GPS Setting 7.4V
—. High Type Absolute High Type Absolute
Speed Unit Knots - Speed Unit Knots
(4.2) Speed Unit
Press UP or UN to select the Speed Unit
on the GPS setting interlace and it includes
Date Type DDrMMrW Date Type DDrMMrW knots and km/h and relative. Select the
Time Zone UTC 08:00 Time Zone UTC 08:00 desved item.
(4.3) Date Type
Press UP or UN to select the Date Type on the GPS setting interface and it includes DD-MM-YY, MM-DD-
YV and VYeMMeDD. Select the desired item.
GPS Setting 7.4V GPS Setting 7.4V
High Type Absolute High Type Absolute
Speed Unit Knots Speed Unit Knots t4-4lT'me 2°"e
Press UP or DN to select the Time Zone,
press R or L to set the desired Time Zone.
—> Date Type DD'MM'VY Date Type DD'MM'W
Time Zone UTC 08:00 —v Time Zone UTC 08:00
3.0 Funct Menu
The Function Menu allows you to customize the settings tor your saved models. This menu includes the
following: Channel Reverse SWitch, Travel Adiust, Sub Trim, Dual Rate and Exponential, Throttle Curve,
Dirterential, Balance, Aileron to Rudder Mix, Rudd to Aile/Elevator Mix, Program Mix, Monitor, Fail Sate,
Sensor View,Trainer and Timer.
3.1 Reverse Switch
Press ENT to the Main Menu. Press UP or DN to move the cursorato point to Function Menu, press ENT to
Function Menu; Press UP 0r DN to move the CUTSOIT‘IO point to Reverse
SWitch, press ENT to Reverse Swttch setting interface. RBVBI‘SB SWitCh 7-4V
Press UP or DN to move the cursorato point to ELEVttaKe Elevator for _. Elevator Normal
example), Press R or L to shifl the status between nomal and reverse. These _
are two status for option. And the detault setting is Normal. All Channels A'lem" Normal
Reverse Switch like Aileron, Throttle, Rudder can be referred to the way Throttle Normal
oi ELEV Reverse Swttch. And press EXT to exit after setting iinished.
3.2 Travel Adjust
Press ENT to the Main Menu. Press UP or UN to move the cursorato paint to Function Menu, press ENT
to Function Menu: Press UP or DN to move the cursor rto point to Travel Adiust. press ENT to Travel Adiust
setting interface. The interface display 3 channels servo travel value status.
Rudder Normal
Travel Adiust 17.4V Travel Adiust 17.4V
Elevator -‘U100.0 Elevator U100.0 Press UP or UN to move the cursor >to
0100.0 —. 0100.0 point to “Elevators U" setting (ELEV is used
Anew" L100.0 Aileron L100.0 in the example), press R+ or L- key. can
R1000 R1000 set the travel value while the Elevator
Throttle Throttle towards up. The adjustment range :0.0-
E1183?) E1133?) 150.0%. Factory default setting: 100.0%.
DEVD F4 7:39
oieUeniion
DEVC} Fa
Welcome to use the DEVO F4 transmitter
Press UP or UN to move the cursor rto point to “Elevator's D" setting, press R+ or L- key, can set the travel
value while the Elevator towards down. The adjustment range :0.0450.0%. Factory default setting: 100.0%.
The settings for all channels. Aileron, Throttle. Ruddercan all be set using this process.
Press EXT to exit.
3.3 Sub Trim
NOTE: Sub Trim is used to fine tune the servo neutral position during setup. In order to avoid pushing the
servo beyond it's limits and possibly causing damage it is adVised to first mechanically adjust the servo arm/bell
crank to be as close to the neutral point as possible. Only when this is
complete may sub trim be used to make a final adjustment. Sub Trim
Press ENT to the Main Menu. Press UP or UN to move the cursorato point
to Function Menu, press ENT to Function Menu, Press UP or DN to move
the cursorato point to Sub Trim, press ENT to Sub Trim setting interface. Aileron
—. Elevator
The interface display a adjustable channel‘s name and adjustable data Throttle
project. Press PR or L- can adiust the fine tune the servo neutral position. Rudder
Press UF' or DN can select the Channel you wish to set. Every Channel
detault setting value is 0.0%. The adiustment ranges are as below
Adjustment range Adius‘mem range
_levator D62. 5%~U62. 5% Throttle L62. 5% ~H62. 5%
R62.5%~L62.5% Rudder R62.5%~L62.5%
Press EXT to exit.
3.4 Dual Rate and Exponential
This function can be setting the amount of action for Elevator, Aileron, Tail Servo. The setting range is
0-125%. It can assist and adjust to fit With Exponent Cunle and various settings.
Dual Rate and... 17.4V
Press ENT to the Main Menu. Press UP or DN to move the cursorato point Pos 0
to Function Menu. press ENT to Function Menu; Press UP or DN to move —> Channel
the cursorato point to Dual Rate and Exponential, press ENT to Dual Rate
and Exponential setting interface.
Elevator
Position Pos 0
Dual Rate 100
(1) Channel
Press UP or DN to move the cursorato point to Channel setting, press R+ or L- key, can set the Channel
as follows : ELEV. AILE and RUDD ect.
Dual Rate and... £7.4V
(2) Position
Press UP or DN to move the cursorato point to Position setting item, with Channel P05 0
“Pos 0. Pos 1" two potions. For example. the “Elevator" of “Channel". if Elevator
select the “Pos 0" which means the setting parameter of “Pos 0". It select —~ POSition
"Pos 1" which means the setting parameter of Pos 1. P05 0
Dual Rate
100
(3) Dual Rate
Press UP or DN to move the cursorato point to Dual Rate setting, press R+ or L- key, can set the “Position
dual rate value. The default setting is 100%.
Dual Rate and... 17.4v Dual Rate and... i7.4v (4) Exponential
Press UP or DN to move the cursorato
Pos 0 Pos 0
Channel - point to Exponential setting. press R+ or i.-
Elevator Position P05 0 key, can set the “Position" Exponential
. . _ 0
Position Pos 0 Dual Rate 100 value. there. are ,100/u and LINE three
settings available.
—~ Dual Rate —~ Ex onential
100 p Line Press EXT to exit.
DEVO F4 7 4D
oieUeniion
DEVD F4
Welcome to use the DEVO F4 transmitter
3.5 Throttle Curve
Throttle Curve are adjusted through 7 points.
Press ENT to the Main Menu. Press UP or UN to move the cursorato point to Function Menu, press ENT
to Function Menu; Press UF‘ or UN to move the cursorato point to Throttle Curve, press ENT to Throttle
Curve setting interface.
_ , Throttle Curve 7.4V Throttle Curve 17.4V
The Interface of Throttle Curve wtll pop up _' Position
“All servos Hold?" inquire, if you choose Pos 0
“OK"every servo will hold at current position, A” Servos Hold? Exponential
if you choose “Cancel" every servo won't _. OK OH
be hold. P0“
Cancel
In: 0.0
(1) Position selection
Press UP or DN to move the cursorato point to Position setting item, with ”Pos 0, Pos 1" two potions. It select
the "Pos 0" which means ordered curve parameters ot"Pos 0". Also, select “Pos 1" is the same means.
(2) Exponential curve setting Throttle Curve £7.4V
Press UP or DN to move the cursordto point to “Exponential" setting. Press Position
R or L can set ON and OFF. The throttle curve will being changed smoothly
if select 0N. Select OFF if not need then the throttle curve will be shown - Exponential
as a line. See the right Illustration:
Pos 0
Off
Point
Throttle Curve (3) Curve setting:
Position Including “Paint" and “Output"
Exponentia| (3.1) Point setting
In: 0.0
_, Paint Press UP or UN in Throttle Curve intertace to select Points setting. Press
R+ to expand a list including seven points: “PointL”, “PoinH”, “Pointy",
In: 0.0 “Point-M". “Point-3", “Point-4" and “Point-H".
(3.2) Status setting
After above setup, press DN to select Status setting. press R-t- or L- to set Inhibit or Active. Select Inhibit it
Keeping the current value (the detault setting is Inhibit). Select Active for changing the above points‘ value.
Note: After select Point L or Point H, the status setting won't be display.
Throttle Curve Throttle Curve t7.4V
Point Point
Throttle Con/e 77.4V
Point -M _' Pom Point -L
-> Status - Status Active
Output Output
50.0
In: 0.0 Out: 0.0 In: 0.0
Throttle Curve
(3.3) Output setting ,
Point
There is a expand item “Output" after select Status Active, press UN to
select Output setting, press R+ or L- to increase or decrease, respectively, Status
the output value. The adJustable range is trom 0.0% to 100.0%. “IN" and
“Out” means throttle stick input and output level.
-' Output
In: 0.0
Throttle Curve t17.4V (4) Throttle Stick setting
Status The switch between Pos 0 and Pos 1 can be freely realized through throttle
stick after the below amount has been set up. The below set amount is
Output 50 o the position of throttle stick as well as the switch point.
_. Throttle Stick Throttle setting: Press UP or DN to move the cursorato point to Throttle
Stick seting, Press L to decrease the amount with a lower limit at 0.0% or
In: 0.0 Out: 0.0 Inhibit, Press R+ to increase the amount with an upper limit ot 100.0%.
Active
Inhibit
DEVD F4741
oieUeniion
DEVD F4
Welcome to use the DEVO F4 transmitter
(5) SWitch Selection
When the item Throttle Stick is set in Inhibit, it is possible to switch between Pos 0 and P05 1 by SWitch.
Press UP or UN to move the cursor *1!) point to “Switch". Press ENT to enter into SWitch selection interface,
press UP or DN to move the cursorato .
point to the desired item. Press ENT, the Throttle Curve 174V SWI‘Ch
desired item whose left side will be changed Output 503 —‘ 0 And
into “1" from ”".0 If two or more items are Throttle Stick I h'bt 0 spso sw
Ise'l‘eotgd, tlge itambshoxld be :hosen,1whose _. 5 ‘ h n I i 0 3,331 SW
e si e s ou e c ange in o roni Wl c P05 0 0 SPSZ SW
“0". Press EXT after finished it.
Iri: 0.0 Out: 0.0 0 SPS3 SW
Attention: The Stick SWitch is needed, find out 2.8 Stick Position Switch and start using, otherwise, cannot
enter into this function.
3.6 Differential
If want to use this function, Delta should be preViously selected in Wing Type of Model Menu. Refer to “2.9
Wing Type".
Differential
(1) Aileron differential setting
Press ENT to the Main Menu. Press UP or DN to move the cursor ’to point _' Channel
to Function Menu, press ENT to Function Menu; Press UP or UN to move
the cursordto point to Differential, press ENT to Differential setting interface.
See the right Illustration Pos 1
Pos 0
Mounting servos in left and right ailerons are a necessary if using this function. The following interface will
be shown after Delta selected in Wing Type. Refer to “2.9 Wing Type".
(1 .1) Channel: Current setting channel is Aileron. System default can not be set.
(1.2) Setting for Pos 0
Press UP or DN to move the cursorato point to Pos 0, press R or L to increase or decrease differential value,
respectively. The adjustable range is i 100%.
Differential Differential
(1.3) Selling for Pos1
Channel Channel Press UP or DN to move the cursorato
- Pos 0 P05 0 point to Pos1, press R or L to increase or
decrease differential value, respectively.
P051 _' P051 The adjustable range is :100%.
(1.4) SWilch selection
It is possible to switch by Selling Switch when differential is in use.
Press UP or UN to move the cursorato point to Switch, press ENT to enter interface of SWitch selection,
Press UP or UN to move the cursorato
point to desired item. Press ENT, the desired Differential SWi‘Ch
item whose left side Will be changed into P05 0 —* 0 And
“1" from “".0 If two or more items are OSPSO SW
selected. the item “And" should be chosen, Pos 1 0 5,351 SW
whose left side should be changed into “1"
from “0“. Press EXT after finished it.
-’ SWitch 0 SPSZ SW
0 SP33 SW
Attention: The Stick sWitch is needed, find out 2.5 Stick Position Switch and start using, otherwise, cannot
enter into this function.
DEVD F4 7 42
oleUenlion
DEVD F4
Welcome to use the DEVO F4 transmitter
(2) Rudder differential setting
V-Tail should be previously set in Wing Type of Model Menu if the rudder
differential function is activated. Refer to “2.11 Wing Type". On the interface — Channel
of Differential, press UP or DN to move the cursoreto point to Channel,
the Channel item will show the present setted channel is “Rudder". The P05 0
system default is not available to set up. Pos 1
(2.1) Setting for Pos 0
Press UP or UN to move the cursoreto point to P05 0, press R or L to
increase or decrease differential value, respectively. The adjustable range is t 100%.
Differential
Differential Differential
(2.2) Selling for Pos 1
Channel Channel Press UP or UN to move the cursorato
—> p05 0 Pos 0 point to Pos1, press R or L to increase or
decrease differential value, respectively.
P05 1 “ P05 1 The adjustable range is t 100%.
(2.3) SWitch selection
It is possible to switch by Setting Switch when differential is in use.
Press UP or DN to move the cursorato p0int to Switch, press ENT to enter interface of SWitch selection,
Press UP or UN to move the cursorato
point to desired item. Press ENT, the desired Differential SWilCh
item whose left side Will be changed into Pos 0 -' 0 And
“1" from “"0. If two or more items are OSPSO SW
selected, the item "And" should be chosen, p05 1 0 SPSt SW
whose left side should be changed into “1"
0 SPS2 SW
0 SP83 SW
from ““.0 Press EXT after finished it. _' SWllCh
Attention: The Stick sWitch is needed, find out 2.5 Stick Position Switch and start using, otherwise, cannot
enter into this function.
3.7 Balance
This function can make the tworchannel output parameters of two seros are adjustable. When the function
is using, make to sure the “Delta“ or “V-Tail" is effective. Refer to “2.9 Wing Type"
Setting method‘ Balance 17.4V
Press ENT to the Main Menu. Press UF' or DN to move the cursorato point
to Function Menu, press ENT to Function Menu; Press UP or UN to move Channel
the cursordto point to Balance. press ENT to Balance setting interface.
See Illustration:
(1) Channel Point- Right Inhibit
The channel item will show the present setted channel is “Aileron”. The
system default is not available to set up.
- Aileron
Paint < Right
(2) Point parameter adjustment Balance ”AV
Point< Right Setting: Press UP or UN to move the cursorato point to “Point< Channel
Right". If need to adjust the value, press L (0% means no adjusting). A _ Aileron
minus value means the amending direction is downward; press R to adjust PM“ < R'Ql‘l _. 0
value(0% means no adjusting). A plus value means the amending direction Point _ Right
is upward. The adjustable range is :100%. Inhibit
Point-Right Setting: Press UP or DN to move the cursor rto point to “Point-Right". Press R or L to inhibit or
active. If need to adjust please active it. There Will be expanded value adjustment item. Press UP or UN to
move the cursor rto point to “0%". it need to adjust the value. press L (0% means no adjusting). A minus
value means the amending direction is downward, press R to adjust value (0% means no adjusting). A plus
value means the amending direction is upward. The adjustable range is 1100%.
DEVD F4 7 43
oieUeniion
DEVD F4
Welcome to use the DEVO F4 transmitter
Balance 17.4v Balance 17.4v
Channel Channel Al Press UP or DN, there will be setting for
Aileron _ ‘emr‘ Point-1, Point-2, Point-3. Point-Left,
Point < Right 0 PW“ < R'gh‘ 0 Point>Left, refer to the setting method as
above. Press EXT after finished it.
_ Point . Right
Point Right. Inhibit —- Active
3.8 Aileron to Rudder Mix
This function is possible to execute the mix ofaileron to rudder, which is controlled by switch.
Setting method:
Aileron to Ru... 17.4V
Press ENT to the Main Menu. Press UP or DN to move the cursorato point
to Function Menu. press ENT to Function Menu; Press UP or UN to move —' P05 0 Le"
the cursoreto point to Aileron to Rudder Mix, press ENT to Aileron to Rudder .
. . Pos 0 Right
Mix setting interface. See Illustration:
Pos l Left
(1) Pos 0 Setting leftward setting
Press UP or UN to move the cursorato point to leftward mix value, press R or L, leftward mix value of aileron
to rudderWill be changed. The mix direction Will be revised by changing the sign of plus or minus before the
value. The adjustable range is t125%.
(2) Pos 0 Setting rightward setting
Press UP or DN to move the cursoreto point to rightward mix value, press R or L rightward mix value of
aileron to rudder will be changed. The mix direction will be revised by changing the sign of plus or minus
before the value. The adjustable range is :125%.
(3) Pos 1 setting, reference Pos 0 setting.
(41Th’0'l'e 5““ ”NW Aileron to Ru... n7.4v
The switch between Pos 0 and Pos 1 can be realized by setting the position
of throttle stick. Press UP or DN to move the cursorato point to "Throttle P05 1 Le"
Stick” setting, press R or L to change the value or inhabit The Throttle Pos 1 Ri ht
Stick postion can be set when changing the value.The default setting is g
“Inhabit". The adjustable range is from 0.0% to 100.0% —~ Throttle Stick l h'b't
n i i
(5) SWitch setting
Press UP or DN to move the cursorato point to Switch, press ENT to enter interface of SWitch selection,
Press UP or UN to move the cursor -to
point to desired item. Press ENT, the desired Aileron to R“"' 174V SWitch
item whose left side will be changed into P05 1 Right * 0 And
“i" from “0". If two or more items are 0 USPSO SW
selected, the item “And" should be chosen, Throttle Stick p 1 W
whose left side should be changed into “1" Inh'b't 0 S S S
from ““0. Press EXT after finished it. —' SW“Ch 0 SFSZ SW
P05 0 o SP83 sw
Attention: The Stick sWitch is needed, find out 2.8 Stick Position Switch and start using, othenivise, cannot
enter into this function.
3.9 Rudder to AileranlElevator Mix
This function is used to execute the mix of rudder to aileron/elevator. It will help eliminate waver or shake
caused by rudder stick operation.
Setting method'
Press ENT to the Main Menu. Press UP or DN to move the cursorato point to Function Menu, press ENT
to Function Menu: Press UF' or DN to move the cursordto point to Rudd to Aile/Elev Mix, press ENT to
Rudd to Aile/Elev Mix setting interface. See Illustration:
DEVD F4 7 44
oleUenlion
Welcome to use the DEVO F4 transmitter
DEVD F4
Rudd to Ailel... 17.4V l1) Elevalor setting
_. Elevator Pos 0 Left (1.1) Elevator Pos 0 Leftward setting
0 Press UP or DN to move the cursorato point to “Elevator P05 0 Leftward
Elevator Pos 0 Right setting" item, and press R or L to change the value and the Elevator mix
0 amount when operating Rudder leftward The mix direction will be revised
Elevator P05 1 Left by changing the sign of plus or minus before the value.The adjustable range
0 is :125%.
(1.2) Elevator Pos 0 Rightward setting
Press UP or UN to move the cursorato point to “Elevator Pos 0 Rightward setting" item. and press R or L to
change the value and the Elevator mix amount when operating Rudder rightward. The mix direction will be
revrsed by changing the sign of plus or minus before the value. The adjustable range is 1125%.
(t .3) Elevator Pos 1 setting refer to “Elevator Pos 0" setting.
(2) Aileron setting
(2.1) Pos 0 setting: refer to “Elevator Pos 0" setting.
(2.2) Pos 1 setting: refer to ”Elevator Pos 0" setting.
(3) Throttle 5(le setting Rudd to Ailei... 117.4V
The switch between Pos 0 and Pos 1 can be realized by setting the position Aileron Pos 1 Left
of throttle stick. Press UP or DN to move the cursorato point to “Throttle 0
Stick" setting, press R or L to change the value or inhabit. The Throttle
Stick postion can be set when changing the value.The default setting is
“Inhabit". The adjustable range is from 0.0% to 100.0% —> Throttle Stick
(4) Swttch setting inhibit
The switch will display the current swuch position.
Aileron Pos 1 Right
Press UP or UN to move the cursorato point to SWitch, press ENT to enter interface of SWitch selection.
Press UP or UN to move the cursor rto _
point to desired item. Press ENT, the desired Rm“ (0 Ailel... l7-4V SWItCh
item whose left side Wlll be changed into Aileron p05 1 Right _> 0 And
“‘l" from “0". If two or more items are 0
0 SPSO SW
selected, the item “And" should be chosen. Throttle Stick 0 SPsl SW
whose left side should be changed into “1" Inhibit
from “0". Press EXT after finished it. —~ SWItoh 0 5P5? 5‘”
Pos 0 0 SP83 SW
Attention: The Stick switch is needed.
find out 2.8 Stick Posrtion Swrtch and start using, othenwise. cannot enter into this function.
3.10 Program Mix
There are 8 series of program mix, mix channels and values are adjustable.
Setting Method:
Press ENT to the Main Menu. Press UP or UN to move the cursorato point Program Mix
to Function Menu. press ENT to Function Menu; Press UP or UN to move
the cursorato point to Program, press ENT to Program setting interface.
See Illustration: —~ [> Inhibit
And press ENT to program mix setting and current status (default setting Normal
is “inhibit") interface. Press R+ or L- to choose inhibited, normal or curve.
Take “program le 1" for example, there are “normal" and “curve" setting.
Program Mix 1
Curve
(1) The “normal” setting of “program mix"
Press UP or DN to move the cursorato
point to the “Normal" setting, Press ENT
button then pop up "All Servos Hold?" Press
R or L to choose OK or Cancel. If “OK" A” SBNOS Hold?
selected, all the servos Will be locked in the
Current status, if ”Cancel" selected, all servos
are unlocked. Press ENT enter to Program Cancel P05 0 UP 0
Mix 1 setting interface.
Program Mix 1 7.4V Program Mix 1 17.4V
A Master Elevator
—. OK 3'” Elevator
DEVD F47 45
AeUenLon—Welcome to use the DEVO F4 transmitter
DEVD F4
Master
—. p Elevator (1.1) Master channel setting
Aileron Press UP or UN to move the cursorato point to Master Channel setting,
Throttle press ENT to the Master Channel setting interface. Press UP or DN to move
Rudder the cursorato point to the desired Master Channel, press ENT to confirm
and press EXT to be back to Program Mix1 interface.
nglevator
(1.2) stave channel setting: S'aVe
Press UP or UN to move the cursorato point to Slave Channel setting,
press ENT to the Slave Channel setting interface. Press UP or DN to move
the cursor»to point to the desired Slave Channel, press ENT to confirm
and press EXT to be back to Program Mix 1 interface. Throttle
Rudder
—> D Elevator
Aileron
(1.3) Gain setting Take Elevator at Master as an example.
(1.3.1) P05 0 UP
Mix amount setting when elevatorstick moved upward. Press UP or DN to move the cursor >to point to P05
0 UP setting. Press R or L to increase or decrease the mix amount separately. It is possible to reverse mix
direction through changing the “+" or “-’ sign before amount. The adjustable range is t125%.
(1.3.2) Pos 0 Down
Mix amount setting when elevator stick moved
Program Mix 1 117.4V Program Mix 1 N7 4V
a p05 0 up p05 0 Up downward. Press UP or DN to move the
cursorato point to P05 0 Down setting. Press
P03 0 DOW” “P05 0 DOW" RorLtoincreaseordecreasethe mixamount
separately. It is possible to reverse mix direction
through changing the “+“ or “-" sign before
amount. The adjustable range is :125%.
Pos 1 UP Pos 1 UP
(1.3.3) Pos 1 setting: Please refer to “Pos 0 setting".
(1.3.4) Offset Setting
This function can make Slave begin to mix through the corresponding Lever swttch from a certain point as
the starting point.
Press UP or DN to move the cursordto point to Offset setting, Press R+
to increase the mix amount and press L- to decrease It is possible to _. Off t
reverse Offset direction by pressing R or L button to change the “+" or U 59 0
sign before amount. The adJustabie range is :100%. Throttle Stick
Program Mix1 17.4V
Inhibit
Program Mix 1 t7.4V Swttch
Pos 0
(1.4)Throttie stick setting
0 Press UP or DN to move the cursor ’to point to “Throttle Stick" setting,
- Throttle Stick _ press R or L to change the value or inhabit. The Throttle Stick postion can
Inh‘b" be set when changing the vaiue.The default setting is “Inhabit". The
p05 0 adJustable range is from 0.0% to 100.0%
Offset
Switch
(1.5) SWitch setting
The switch will display the current swttch posnion. Press UP or DN to move the cursor >to point to Swttch,
press ENT to enter interface of Swttch
selection; Press UP or DN to move the Program Mix 1 ”AV SWi‘Ch
cursoreto point to desired item, press ENT, Offset -> 0 And
the desired item whose left side will be 0 o SPSO SW
changed into “1" from ‘0". If two or more Throttle Stick 0 SPSt SW
, .i .i Inhibit
items are selected, the item And should 0 SPSZ SW
be chosen, whose left side should be “SW“Ch
changed into “1“ from “".0
After finished, press EXT to return to Program Mix interface and set other items or Press EXT again to exit.
Attention: The Stick swttch is needed, find out 2.8 Stick Position Switch and start using, otherwise, cannot
enter into this function.
P05 0 o SP33 sw
DEVO F4 7 46

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-702
Create Date                     : 2013:02:28 17:55:46+08:00
Creator Tool                    : pdfFactory Pro www.fineprint.cn
Modify Date                     : 2013:03:01 10:17:35+08:00
Metadata Date                   : 2013:03:01 10:17:35+08:00
Format                          : application/pdf
Creator                         : Administrator
Title                           : ~$DEVO-F4封底.pdf
Producer                        : pdfFactory Pro 4.50 (Windows XP Professional x86 Chinese)
Document ID                     : uuid:e4e51e89-54a8-4374-916e-0c5af9690f58
Instance ID                     : uuid:527afa19-9d34-40aa-aea3-98052861bfc2
Has XFA                         : No
Page Count                      : 10
Page Layout                     : SinglePage
Author                          : Administrator
EXIF Metadata provided by EXIF.tools
FCC ID Filing: S29DEVO-F4

Navigation menu