GuangZhou Walkera Technology DEVO-F4 2.4GHz Transceiver User Manual DEVO F4
GuangZhou Walkera Technology Co., Ltd 2.4GHz Transceiver DEVO F4
Contents
- 1. Users Manual Part 1of5
- 2. Users Manual Part 2of5
- 3. Users Manual Part 3of5
- 4. Users Manual Part 4of5
- 5. Users Manual Part 5of5
Users Manual Part 3of5
oleUenlion DEVI] F4 Welcome to use the DEVO F4 transmitter (2.3) Exponential Press UP or DN to move the cursorato point to Exponential setting item, press R+ or L7 With “Off and On" two options. Select “On" can make the curve change to more circular; It don’t use this function, then, select “Off". (2.4) Point Press UP or UN to move the cursorato point to the setting interface of - Point Program Mix 1 ”7.4V P 'nt rM Point. Press R or L keys of selling point. there are “point-L", “point -1", “point 0' 72", “point 7M", “point 73", “point 74", “point 7H". Choose the points need Status Inhibit adiusting. In: 0 Out: 0 (2.5) Status Setting (There is no Status options when the piont is Point-L or Point-H) After selecting the point that you want to set. press UP or DN to move the cursorato . _ point ‘0 Status “em, press R+ or L: there Program MIX 1 ll7.4V Program MIX 1 T17.4V are two options of Inhibit and Active. Select Point Point -M Point Point -M Inhibit for unchanging the current amount _, Status _, Status eeauseinisnii. nil cive thdt It tt'g Ihb't Ihb't At Output 0 Program Mix1 ”7.4V Out: 0 In: 0 Out: 0 Point Pm” 'M (2.6) Output Active When the Status option is Active, the Output option will be listed. Press DN 0 to move the cursor4to point to Output setting, press R or Le to increase or decrease, respectively. the output value. The adjustable range is from In 0 011110 0.0% to 100.0%. ‘IN" and “Out" means throttle stick input and output level. Status -’ Output (2'7) SWitch Program Mix 1 r7.4v SWitch Press UP or DN to move the cursor ~to _. point to the Switch setting item and press Status Active D $33355]; ENT to enter the select interface cl SWitch. Output 0 Press UP or UN to choose the switch you sPsi SW wish to set. Press ENT to conlirm. On SPSZ SW In: 0 SPS3 SW -’ SWitch Press EXT key to return to the previous interface tor other settings or press EXT key to exit after finished. Notes: Enable the Stick Switch at “2.8 Stick Position Switch" setting item. 3.7 Monitor This function can display the current status and positions of all the channels' outputs, and check the current working status of each channel. Press ENT to the Main Menu. Press UP or DN to move the cursorato point Monitor to Function Menu, press ENT to Function Menu; Press UP or DN to move Elevator 0 the cursorato point to Monitor, press ENT to Monitor setting interface. See Aileron 0 below to check the current working status of each channel. Press EXT to exit. Throttle L100 Rudder D 3.8 Fail Safe There are two possibilities for use it the transmission signal is under abnormal condition. The first one is to lock the last action data received; the second one is to execute the preset data which is pre-set. The default setting is Sen/o Hold. Fail Safe ”AV - , Elevator Setting method. _, Servo Hold Press ENT to the Main Menu. Press UP or DN to move the cursordtc point Aileron to Function Menu, press ENT to Function Menu; Press UP or DN to move SEND How the cursordto point to Fail Sale. press ENT to Fail Safe setting interface. Throttle Servo Hold Take the item Elevator as an example. DEVD F47 25 oIeUenIion DEVE} F4 Welcome to use the DEVO F4 transmitter Press UP or DN to select Elevator on the Fail Sale interface, then press R or L to change the status of Sen/o Hold into Fall Sate(lfyou Want to keep Servo hold status, there is no need to re-set).There Fa‘I Safe I7-4V FalI Safe I7.4V is a expanded sub-item blow. Press UP or Elevator Elevator , DN to select 0%.then press R+ or L- to _' Fa‘I Safe _. FalI Site increase or decrease, respectively, the Aileron O Aileron 0 position amount which centers on the neutral SSN° H°Id SEND HOId point of servo. The available value is 125%, Throttle Throttle . . . Servo Hold Servo Hold respectively. 0% Is the neutral point of servo. The setting methods for other channels are same as above. Press EXT to exit after linished. Note: Checking whether all the actions when fall safe happened are correct, ls a must after the setting ls tinished. It is dangerous to use full throttle, especially after fail sate taken place. 3.9 Sensor View Setting method, Press ENT to the Main Menu. Press UP or DN to move the cursorato paint to Function Menu. press ENT to Function Menu: Press UP or DN to move the cursorato point to Sensor View, press ENT to Sensor View setting interface. If all the sensors disconnect, telemetry signal lost, there will be inhibits Sensor VIEW I7'4V shown on the view. If all work normal, all the measured data Will be shown. Inhibit Inhibit lnhlblt lnhlblt Inhibit Inhibit Inhibit Inhibit Inhibit (1) Voltage' Show 3 diffferent measured voltage value; (2) Temperature: Show 4 different measured temperature value; (3) Rate Sensor: Show 2 different measured RPM value; 4) GPS Sensor: Press UP or UN to turn to GPS function, show located date, time, longitude, latitude, altitude and speed; Sensor View Sensor View 17.4V 5.8V - - (2) Tammam East 11323.7255 (I) Image 3.3V Nomi 22 53.4659 0-0V T (4) cps Sensor 156m (3) Ram 59m, 5000RPM 0.0Knots 4000RPM 25-12-2012 14:25:30 3.10 Trainer Two DEVO F4 transmitters can be made to work together in order to offer a teacher-trainer function, meeting the requirements for a beginner. The setup of training mode is described below: (1) Model data transmission First step is to use the DEVO F4's wireless data transmission feature to transfer the teacher‘s main model data to the trainee's DEVO F4 transmitter. This step guarantees that the model data in each transmitter is identical. Refer to item “2.4 model wireless copy" in the Helicopter section later in this manual. Two DEVO F4 transmitters are needed for Wireless data transmission. (2) Training connection 00:00 01 H6 Insert the signal Wire lrom the trainer's transmitter into the DSC socket ol the trainee's transmitter. Turn on the transmitter and a linkage icon, PC-Link Will be shown on the boot screen. Insert one end of the signal Wire (included) into the DSC socket of the trainee‘s transmitter and turn it on. PC-Link will be shown in the trainee's DEVO F4 display (see image right). DEVD F4 7 EB oleUethion DEVE} F4 Welcome to use the DEVO F4 transmitter linkage icon Turn on the power of the trainer's DEVO F4. Select the same model as the trainee (as transferred in the previous section) and briefly fly the aircraft to confirm the settings are good. Turn off the aircraft and turn off the trainer's DEVO F4 power. Insert the other end of the signal wire into the trainer‘s DEVO F4 DSC port and turn on the power once more, T-Ready Will be shown in the trainee's DEVO F4 display (see image left). 00 00 01 H6 (3) Traniner Function Channel Setup The trainee can inquire the control part or whole channel operation by setting the trainers function channel. Here is the setup: Press ENT to the Main Menu. Press UP or DN to move the cursorelo Trainer 7"” point to Function Menu, press ENT to Function Menu, Press UP or DN _. Elevator Inhibit to move the cursoreto point to Trainer. press ENT to Trainer Function setting, Press UP or UN to move the cursorato point to the desired setting Ailercn Inhibit channel, there are Elevator, Aileron, Throttle, Rudder channels available. Throttle Inhibit Press R or L7 to set Active or Inhibit forthe choosed Channel. Rudder Inhibit (4) Training mode usage Trainertoggle keys is R+ button, as illustration_ 00-00 01 H6 T’ka 7-4V On a flight. it the Trainer press the button R+, T it means the Trainer turn over the command to Training sWitch display the Trainee to operate. Meanwhile, the starting up picture will be showmg T-Work. The showing Moving cursor up/Triarier throttle date is the trainee operated. lfthe Trainer toggle keys or increase press the R+ again, it means the trainer retract setting value. the command and operate by the trainer. DEVD F47 27 AeUenLon—Welcome to use the DEVO F4 transmitter DEVI] F4 3.11 Timer There are two timers which can be set as stopwatch and countdown. respectively. Each timer can be operated by switch or by shortcut. Setting method: Press ENT to the Main Menu. Press UP or DN to move the cursordto point to Function Menu, press ENT to Function Menu; Press UP or DN to move the cursorato point to Timer, press ENT to Timer setting interface. See the right Illustration: Timer 7.4V —~ Type Sto pwatch S 'I h "V”: Inhibit (1) Type Press UP or DN to move the cursorato point to Type. Press R+ or L- to choose Stopwatch or Countdown. The default setting is stopwatch. The time range of stopwatch is from 0 to 59 59 (59 minutes 59 seconds). (2) Countdown setting It you need countdown time mariner, press R+ or L- to select the countdown. There is an expand sub-menu set time item. Press UP or DN to select the option of Set time Item. Press R+ or L- to set the countdown time. The settable countdown time range is from 00:05 to 59:55. Timer 7.4V —~ T e yp Countdown Set Time 10:00 sw'mh Inhibit (3) SWltch selection Press UP or UN to move the cursorato point to Switch setting. with “lnhbit” and optional switch item. If select stch, press L- or R+. Available to select other sWitches SPSO SW, SPS1 SW, SPSZ SW, SP53 SW, need to set “Stick Position Switch" of the “Model Menu" and then is effective(reter to “2.8 Stick Postion Switch"). (4) Usage of timer Press UP or DN by pressing UP key for one time, and to pause it by pressing it the second time. Press DN to cleartimer. It's ok to control time by SWitch when time setting is finished on when Timer Will be shown in main interetace. as below illustration: Oi H6 Timer display DEVD F4723 Part three Airplane JeUen ion DEVO F4 All the functional settings, which are relative to the operation system of DEVO F4 itself, are fully integrated in System Menu. They include Display, Buzzer, vibrator, Video Select, Stick Mode. Stick Direction. Stick calibration, and About. Setup your DEVO F4 transmitter for the best Helicopter performance with the following sections. Included are specific functions for rotor-craft features; Throttle cuNes, Pitch curves and Cyclic response are covered below. oieUeniion DEVI] F4 0 System Menu This section describes the settings which are Specific to the operation at the DEVO F4 itself. Settings tor Display, Buzzer, Vibrator, Video Select, SthK Mode, Stick Direction, Stick Calibration and About can be accessed via the System Menu. Welcome to use the DEVO F4 transmitter Below is the boot screen of Airplane: Airplane Type display Model No. display Output Power display Timer display Battery charge indicator Throttle level display Aileron trim display Rudder trim display Throttle trim display Elevator trim display 1.1 Display Baoklight intensity the backlight intensity is adiustable using the UP or DN button. Power consumption will be increased when intensity is high and battery life will be reduced. Setting Display 7.4V Press ENT to the Main Menu. Press UP or DN to move the cursorato point to System Menu, press ENT to System Menu; Press UP or DN to move the cursoreto point to Display, press ENT to the Lightness setting intertace and use R or L to change the setting as desired. Press EXT to exit. —. Lightness 5/10 1.2 Buzzer Setting (1) Status Press ENT to the Main Menu. Press UP or DN to move the oursorato point to System Menu, press ENT to System Menu; Press UP or DN to move the cursor -to point to Buzzer, Buzzer 7'4V press ENT to the Buzzer setting _, Status On interface. And then press UP or DN to move the cursoreto point to the Status, Throttle SUCK press R or L to toggle between ON and Inhibit OFF settings. ON means startthe Buzzer while OFF means the Inhibit. Tone “10 (2) Throttle stick: With the “Status" item on, the option THSTK can be set to ON or OFF. If the Throttle Stick setting is ON/Active, a musical scale Will be heared when moving the throttle stick. The position of the throttle stick can be judged by listening to the change in musical tone. Setting OFF, turns off the sounds. Buzzer . Buzzer . Setting: With the ”Status" item on, press DN to 5‘3“ O" 5‘3“ 0" move the Cursorato point to the “Throttle _. Throttle Stick _. Throttle Stick Stick“. Use R or L to change the display Inhibit Active between Inhibit and Active. Active means tones will be played, Inhibit means there Tone 1’10 Tone 1’10 Will be no tones played. DEVD F4730 Welcome to use the DEVO F4 transmitter—AeUenlflonv DEVD F4 (3) Tone: The buzzer tone can be selected from 10 notes. You can set the tone according to your preference and test the performance. Setting: Buzzer 7.4V With the “Status" item on. press UN to move the cursorato point to Tone Sla‘us On item. Use R or L key to change the flashing value from i to 10. Press EXT to exit alterfinished. Throttle SliCk Active 1.3 Vibrator — Tone 1/10 The vibrator is used as an alarm function to remind the users. Setting: Press ENT to the Main Menu. Press UP or DN to move the cursorato point to System Menu, press ENT to System Menu; Press UP or UN to move the cursoreto point to Vibrator, press ENT to Vibrator setting interface. Vibrator 7.4V Vibrator 7.4V There are two status as Inhibit and Active. _. Status . . _. Status Press R or L to select Active or Inhibit. Inhibit Active Active means to start vibration. Inhibit means to turn off vibration. Press EXT to exit after finished. 1.4 Video Select This function provides the settings of Inhibit or Active when choose the Video option. There are 8 channels for your choice at the state of Active. Setting: Press ENT to the Main Menu. Press UP or DN to move the cursor -to point to System Menu, press ENT to System Menu; Press UP or DN to move the cursorato point to Video Select, press ENT to Video Select setting interface. Video Select . Video Select 7.4V Press R or I. to make the status to change Active or Inhibit, Active means to start using. —~ Status —~ Status _ Inhibit means to turn off. After Active, the Active interface Will be show channel selection. Channel 1/8 Video Select 7.4V Channels options: Press UN to move the cursoreto point to Channel item Status Active as shown in the above interface. Press R or L to make the Number change between 1 to 8. With the 5.86 image transmmision module,1-8 channels —. Channel could be choosed to receive the image signal. 1/8 Press EXT to exit after finished. 1.5 Stick Mode There are 4 stick modes including Mode1, ModeZ. Mode3 and Mode4. Right-hand throttle includes Mode1 and Mode3; while left-hand throttle includes Mode2 and Mode4. See Below: Mode 2 and Mode 4 are listed in left-hand throttle. MODEZ Throttle Elevator MODE4 Throttle Elevator Rudder4—1—r Aiieron+ Ai|ergn+ Rudd2r4—1—y DEVD F4731 oieUeniion DEVI] F4 Welcome to use the DEVO F4 transmitter Mode 1 and Mode 3 are listed in right-hand throttle. MODE1 MODES Elevator Throttle Elevator Throttle Rudder+ Aileron4—I—> AiIgf0n+ Rudder<—1—> Setting: Press ENT to the Main Menu. Press UP or DN to move the cursor >to point to System Menu, press ENT to System Menu; Press UP or DN to move the cursorato paint to Stick Mode, press ENT to Stick Mode setting interface. SliCk Mode There are mode 1, mode 2, mode 3 and mode 4 for options. Press UP or —r i> Mode 1 UN to move the cursordto point to desired item and then press ENT to Mode 2 confirm. Mode 3 Mode 4 Press EXT to exit after finished. 1.6 Stick Direction Setting: Press ENT to the Main Menu. Press UP or UN to move the cursorato point to System Menu, press ENT to System Menu; Press UF' or DN to move the cursordto point to Stick Direction, press ENT to Stick Direction setting interface. Stick Direction 7.4V " E'eVaW Normal Stick Direction There are Elevator, Aiieron, Throttle, Rudder for options. Mew" Normal Press UP or UN to move the cursorato point to the desired item. Press R or L to change the settings of corresponding sticks. There are Normal Throttle Normal and Reverse. The default setting is Normal. Rudder Normal 1.7 Stick Calibration Setting: Press ENT to the Main Menu. Press UP or DN to move the cursorato point to System Menu, press ENT to System Menu; Press UP or DN to move the cursor >to point to Stick Calibration. press ENT to Stick ENT to Calibrate Calibration setting interface. Stick Calibra... 7.4V Stick Calibration: Mechanically move the right stick and left stick from their minimum levels to their maximum levels several times, and then return the sticks to the neutral positions, respectively. Stick Calibra... . Stick Calibra... 7.4V ENT to Finish ENT to Calibrate Press ENT again to stop the calibration process and the display should show the Calibration Success following interface(Calibration Success). The calibration has failed if press ENT and show the following interface. Please go back to the STMOD sub- menu using EXT and re-start the calibration process. Press EXT to exit aftertinished. Stick Calibra... ENT to Finish Please Retry DEVO F4752 oleUeniion DEVD F4 Welcome to use the DEVO F4 transmitter 1.3 About Setting: Press ENT to the Main Menu. Press UP or DN to move the cursordto point to System Menu, press ENT to System Menu; Press UP or UN to move the cursorato point to About, press ENT to About setting interface. You can check the current verSions of hardware and software. Press EXT to exit after finished. 2 Model Menu Model Menu manages all the model data saved in DEVO F4. It Includes Model Select, Model Name, Model Copy, Model Transmit, Model Receive, Model Reset, Type Select, Trim System, Stick Position Switch, Wing Type, Power Amplifier. Fixed ID and Sensor setting. 2.1 Model Select Model Select t 7.4V Setting: Press ENT to the Main Menu. Press UP or UN to move the cursorato point to Model Menu, press ENT to Model Menu, Press UP or " D ‘l A Model 1 DN to move the cursor rto point to Model Select, press ENT to Model 2 H Model 2 Select setting interface. There are 15 different model settings to be saved. 3 H Model 3 Press UP or DN to move the cursor >to point to select the model No you 4 H Model 4 want and press ENT to confirm. Press EXT to exit. 5 H Model 5 2.2 Model Name In the menu of model name. you can make a desired name for your model for long term storage. Its data can be directly withdrawn in next flights. Repeat the step “2.1 Model Select” to choose the model you want to name or save, press EXT to back to the interface. Setting: Press ENT to the Main Menu. Press UP or DN to move the Model Name - cursor rto point to Model Menu. press ENT to Model Menu; Press UP or DN to move the cursorato point to Model Name, press ENT to Model Name setting interface. Press UP or DN to move the cursoreto point to select the character and figure which are needed to be changed, press R or L button to change the character and figure, and press UP or DN to set next one. Press EXT to exit after finished. No. 1 2.3 Model Copy Setting Press ENT to the Main Menu. Press UP or UN to move the cursorato point to Model Menu, press ENT to Model Menu; Press UP or UN to move the Cursorato point to Model Copy, press ENT to Model Copy setting interface. Model Cow I 7.4v Model Copy 7.4V Source Press UP or DN to move the cursor»to Source: 1 A Model 1 point to select the model you want to be —' l> l A MUdel 1 Desi copied as source model and press ENT to confirm, The serial No. and model name of Source Model Will be shown as Illustration. 2 H Model 2 [>1 A Model 1 3 H Modem _. 2H ModelZ 4 H Model4 3 H Mode|3 Model Copy 7.4V Source: 1 A Model 1 Then press UP or DN to locate the source model, press ENT to confirm. Desi: 2 H Model 2 Then an enquire “Are you sure?” is popped up as Illustration. Press ENT to copy, or press EXT to exit. Are you sure? DEVI: F4 783 oleUethion —Welcome to use the DEVO F4 transmitter DEVD PA 2.4 Model wireless copy The model data between two DEVO F4 equipments can be wirelessly copied Via Model Transmit and Model Receive in Model Menu. (1) Model Transmit Setting: Press ENT to the Main Menu. Press UP or DN to move the cursorato T’ [> 1 A Model 1 point to Model Menu, press ENT to Model Menu; Press UP or DN to move 2 A Model 2 the cursorato point to Model Transmission. press ENT to Model Transmission 3 H Model 3 setting interface. 4 H Model 4 Model Transmit 17.4V 5 H Model5 Press UP or DN to choose the source model which Will be transmitted, and press ENT to confirm, an enquiry information “Are you sure?" will be shown as below Illustration. Press ENT to confirm and EXT to exit. Model Transmit 17.4V Model Transmit 17.4V ND- 1 No' 1 Press ENT to transmit, “Transmitting Model 1 Model 1 ...... " appears in the interfaCe. or press _ ENT to confirm. Press EXT to exit after Are you we? T'a"5"““'"9--- another DEVO F4 received the data. >>>>>>>>>> (2) Model Receive Press ENT to the Main Menu. Press UP or DN to move the cursor >to point to Model Menu. press ENT to Model Menu, Press UP or DN to move the cursorato point to Model Receive, press ENT to Model Receive setting interface. An enquiry information “Are you sure?" will be shown as below Illustration. Model Receive . Model Receive Receive Config Receive Config Press ENTto receive,- “Connecting ...... " and “Receiving .. .,." Will be shown in series in the interface. Are you sure7 Connecting... >>>>>>>>>> After Model received the data will enter to the Model save interface. Press UP or DN to move to the cursorato point to Model data save position. Press ENT will pop up “Are you sure". Press ENT M°de‘ Rece've ”-4" to save, press EXT to cancel . —. D 1 A Model ‘l Model Receive t7.4V No. 3 Press ENT to confirm and EXT to exit. 2 A Model 1 Model 3 3 H Model 3 4 H Model 4 Are you sure? 5 H Model 5 2.5 Model Reset Using the Model Reset function the settings for one or all models can be reset to the factory defaults. Setting Press ENT to the Main Menu. Press UP or DN to move the cursor >to point to Model Menu, press ENT to Model Menu; Press UP or UN to move the cursorato point to Model Reset, press ENT again to display to model selection. Use R and l. to select “ALL“ for all models or the individual model name for a single model reset. Model Reset Model Reset Model All 1 Press UP or DN to move the cursor4 to —‘ l> 1 A Modelt No' point to the desired model No and press ModEl 1 ENT, an inquiry “Are you sure" will be shown 2 A MOdEI i as Illustration. 3 H Model 3 Are you 5W9? Press ENT to reset and EXT (0 CanCEI. 4 H Model 4 Press EXT after finished. DEVD i=4 734 oieUeniion DEVD F4 Welcome to use the DEVO F4 transmitter 2.6 Type Select This transmitter offers a choice of two model types. The options are helicopter and airplane. Press ENT to the Main Menu. Press UP or DN to move the cursor -to point to Model Menu, press ENT to Model Menu, Press UP or DN to move the cursor >to point to Type Select, press ENT to Type Select setting interiace. Helicopter Model Transmit Press UP or DN to move the cursorato point to helicopter or Airplane option. —> D A|rp|ane Press ENT, there is an inquiry shows. Press ENT to select the desired model. If the default model are the desired one. Press ENT and press EXT to exit. 2.7 Trim System Trim System is able to finely tune the following terms, respectively: Elevator, Aileron, Rudder, Throttle. The trim range is divided into 20 grades. (factory detault is set at 4). It is convenient to subtly modify the pitch by adjusting the trim range. Trim System t7.4V Press ENT to the Main Menu. Press UP or DN to move the cursor >to point Elevator —~ 4/20 to Model Menu, press ENT to Model Menu, Press UP or UN to move the NOW?” cursor >to point to Trim System, press ENT to Trim System setting interface. Aileron 4,20 Normal Press UP or DN to move the oursorato paint to the item that need to adjust. Rudder 4,20 Press R+ or L- can change the setup, Maxium is 20. Normal For elevator, aileron and rudder, there are two more options: Normal and Limited. “Normal" means the trim is always working although the corresponding stick stays anywhere. “Limited“ means the Trim System ”AV Trim System ”AV trim is out of working when the corresponding Elevator 4/20 Elevator 4/20 stick is at maximum position. —> Normal —~ Limited Press EXT to exit after finished. New" 4/20 Allen" 4120 Normal Normal Rudder 4/20 Rudder 4,20 2.8 Stick Position Switch Normal Normal According to the tollowmg setting, the stick can be used as a swrtch. The turn-on orturn-oft position at which stick stays can also be settable. Method tor setting: Press ENT to the Main Menu. Press UP or UN to move the cursorato point to Model Menu, press ENT to Model Menu; Press UP or DN to move the cursor -to point to Stick Position Switch, press ENT to Stick Position SWitch setting interface. There are tour options under the Stick position switch: SPSO, SPS1, SPSZ, SPSE}. _, Switch SPSO SW SWitch Spso SW Press UP or DN to move the oursorato point to sWitch option. Press R or L to choose the switch you want to define. Position 0 Press UP or DN to move the cursor >to On Up point to the channel option. There are Inhibit and channel options.(Default setting inhibit) Stick Positio... 7.4V Stick Positio... 7.4V Channel Inhibit —vChannel Elevator The channel includes tour items: Elevator. Aileron. Throttle and Rudder. The factory default is inhibit. Take Elevator for example. Press R or L to choose the Elevator as stick. and then press DN to move the cursorato point to value of position. It's possible to Switch SPSO SW SWitch SPSO SW adjust the stick position via pressing R or L. Stick Positio... 7.4V Stick Positio... 7.4V Press UP or DN to move the cursordto point Channel Elevator Channel Elevator to On option. And then press R+ or L- to —' POSWIO” 0 POSItIOn 0 change the ON status of stick postion On Up —. On Up Press EXT after finished. DEVD F4735 oleUethion Welcome to use the DEVO F4 transmitter DEVI] PA 2.9 Wing Type Wing Type lS grouped into Nornal, Delta and V -Tail. Wing Type selection: Wing Type “W Press ENT to the Main Menu. Press UP or DN to move the cursorato point —~ Wing Type to Model Menu, press ENT to Model Menu; Press UP or DN to move the NOVmE' cursorato point to Wing Type, press ENT to Wing Type setting intertace. V-Tail Press UP 0r DN to move the cursorato point to Wing Type, press R or L to Inhibit choose Normal or Delta. (1) Delta Press R or l. to choose Delta in Wing Type. Below is the graphics of the servos location of the Delta Type. Left Alieron Rignt Aiieron (2) We” connect to the output AILE ll’t Receiver Connect to the output ELEV ln Receiver Press UP or UN to move the cursorato point to V-Tail under Wing Type interface. There are Inhibit and Active, please choose Active. V-tail is unadjustable when the Wing type is Delta. Below is the sketch map of servos‘ assignment in V-tail Lert empennage ngni empennage Connect to the output ELEV in Receiver Connect to the output RUDD in Receiver 2.10 Power Amplifier The transmission output power ot DEVO F4 is adjustable. It is divided into six grades from low to high. The lower the transmission output power transmits, the shorter the radio range is, and the longer the stand-by time Will be, the higher the transmission output power, the farer the radio range, and the shorter the stands by time. Choose the appropriate transmission output power according to the actual situation. Press ENT to the Main Menu. Press UP or DN to move the cursordto point to Model Menu, press ENT to Model Menu; Press UP or DN to move the cursorato point to PowerAmplifler, press ENT to Power Amplifier setting interface. PowerArnplilier . 00:00 01 H6 _. l> 20 dBm Press UP or UN to move the cursorato output power level point to the desired output power value and 15 dBm press ENT to confirm. The output power level Will also show on the main menu interface see the left Illustration: iOdBm DEVO P4 738
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : 3.1-702 Create Date : 2013:02:28 17:55:46+08:00 Creator Tool : pdfFactory Pro www.fineprint.cn Modify Date : 2013:03:01 10:13:38+08:00 Metadata Date : 2013:03:01 10:13:38+08:00 Format : application/pdf Creator : Administrator Title : ~$DEVO-F4封底.pdf Producer : pdfFactory Pro 4.50 (Windows XP Professional x86 Chinese) Document ID : uuid:0aaaf93a-39c1-432e-aef7-58642faaead2 Instance ID : uuid:a2699394-f54a-4d2e-88a0-7440aa7dcf2f Has XFA : No Page Count : 12 Page Layout : SinglePage Author : AdministratorEXIF Metadata provided by EXIF.tools