Honeywell orporated DR4220 Proximity Reader User Manual 7600033D 4220 4 5 02

Download:
Mirror Download [FCC.gov]
Document ID	692296
Application ID	7YvaYrFzaHJ8dV4rrYf3sg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	53.01kB (662605 bits)
Date Submitted	2006-08-10 00:00:00
Date Available	2006-08-10 00:00:00
Creation Date	2006-05-04 12:04:18
Producing Software	Acrobat Distiller 4.05 for Windows
Document Lastmod	2006-08-01 18:20:57
Document Title	7600033D-4220-4-5-02.fm
Document Creator	FrameMaker 6.0

DigiReader ® DR4220
Installation Notes
IC: 573G-DR4220
FCC ID: C4PDR4220
(The term "IC:" before the radio certification number only signifies that Industry Canada technical specifications were met.)
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the device.
August 2, 2006
© 2006 Honeywell International. All rights reserved.
Document 7600033
Revision F
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
DigiReader DR4220 Installation Notes
DIGIREADER DR4220 INSTALLATION NOTES
ON
DIP ADDRESS SWITCH
The DR4220 reader has a 5-position DIP-switch S1, (as
shown to the right, with S-NET address 1 selected).
Switch S1 Settings
S-NET Address
or Function
Off Off Off Off Off Off-line 0
On Off Off Off Off
Off On Off Off Off
On On Off Off Off
Off Off On Off Off
On Off On Off Off
Off On On Off Off
On On On Off Off
Off Off Off On Off
On Off Off On Off
Off On Off On Off
10
OFF
Switch S1 Settings
S-NET Address
or Function
On On Off On Off
11
Off Off On On Off
12
On Off On On Off
13
Off On On On Off
14
On On On On Off
15
Off Off Off Off On
16
Off On Off On On Wiegand I/F (26-bit)
On On Off On On Wiegand I/F (34-bit)
Off On On On On
DEMO Mode
On On On On On
TEST Mode
INTERNAL INTERFACE CABLE
An attached pigtail cable assembly provides the connection from the printed circuit
assembly to the access control unit wiring on a DigiReader DR4220. The cable is colorcoded as follows:
COLOR
Red
FUNCTION
(S-NET Use)
+12.5 to +24VDC
S-NET Nominal
(max. draw 500mA)
Green
S-NET A
For use with NexWatch
access control panels
White
S-NET B
Black
GND
S-NET DC Return
Shield
Earth
S-NET Shield
Blue
Data 0 (Out 0)
Orange
Data 1 (Out 1)
NA
Yellow
LED 0
Brown
LED 1
(Wiegand Use)
Wiegand Nominal
NA
Wiegand DC Return
Wiegand Shield: Tied to Wiegand DC Return
For use with Wiegand
access control panels
(Green) Both LEDs are ACU-controlled
and are ON/low or OFF/high
(Red)
TAMPER
The DR4220 sends a tamper signal to an S-NET-based ACU when a tamper occurs.
P/N 7-600033 Rev. F
©Honeywell International. All Rights Reserved.
DigiReader DR4220 Installation Notes
MOUNTING INSTRUCTIONS:
Carefully choose the installation site to avoid possible external sources of RF interference. Interference may cause reduced performance, so DO NOT locate the unit near
motors, pumps, generators, DC-AC converters, AC switching relays, light dimmers, etc.,
or within 10 feet (3 m) of a computer terminal.
WARNING: DO NOT mount the unit on or near any type
of metal, including nonferrous metals such as aluminum. (Metal may
cause reduced performance or possible damage to the unit.) The unit
may NOT operate properly if it is in near to, or mounted directly on
metal, reinforced steel in concrete, screens, or reinforcing bars. In addition, the unit must not be framed with or surrounded by metal of any kind. If the unit must
be mounted near metal structures, ensure that it has a minimum of 10 inches (25.4 cm)
clearance at the rear and surrounding sides. Never cover the front of the DigiReader with
any type of metal. Metal anywhere near the device can reduce the read range. In general, as the amount of metal close to the device increases, the reliable maximum read
range decreases.
3/4" Plywood or Lexan Sheet
PEDESTAL-MOUNTING
INSTRUCTIONS:
Goose-Neck Assembly Mounted to
Lexan R /Plywood
in Middle of
Transmit
Coil
There must be no conducting metal closer
than 10 inches to the DR4220 reader, except for a unit mounted with a goose-neck
pedestal mounting tube, as shown in figure 1.
The recommended mounting methods follow:
1. Remove the case front (cover).
2. Use the NexWatch-supplied drilling template to pre-drill 4 holes on the plywood
or LEXAN® sheet (recommended ¾" thick).
A channel must be cut into the plywood
or LEXAN® for the cable between the exit
point of the reader and the goose-neck.
3. Mount the plywood or LEXAN® sheet to a
goose-neck pedestal mounting tube. (A
minimum of 10" clearance is recommended
between the back of the reader and the
vertical metal tubing). Center the mounting
tube. (See figures 1 and 2.)
P/N 7-600033 Rev. F
10” Minimum
Clearance Between
Back of Reader and
Vertical Metal Tubing
Figure 1
Figure 2
©Honeywell International. All Rights Reserved.
DigiReader DR4220 Installation Notes
4. See the INTERNAL INTERFACE CABLE
section on page 1 to install the colorcoded pigtail cable.
5. Route the cable through a channel on the
plywood or LEXAN® sheet. (See page 4:
RECOMMENDED STAND-OFF PLATE.)
6. Mount the DR4220 board and case back
(back plate) to the plywood or LEXAN®
sheet which is securely attached to the
goose-neck as shown in figure 3.
7. Set the address switch, as required.
8. Install the case front (cover) and be sure
that the LED is not damaged as it enters
the lens assembly.
9. Secure the case front four holes with the
supplied screws. (See figure 4.)
Figure 3
WALL-MOUNTING INSTRUCTIONS:
There must be no conducting metal closer than 10 inches to the DR4220 reader.
The recommended mounting methods follow:
1. Remove the case front (cover).
2. Use the NexWatch-supplied drilling template (included with reader) to drill four
holes in the wall.
3. Follow the INTERNAL INTERFACE CABLE
instructions to install the pigtail cable.
(See page 1.)
4. Mount the DR4220 board and case back
(back plate) using 2¼" Panhead #6-32
thread screws (or other means appropriate to the wall composition).
5. Set the address switch, as required.
6. Install the case front (cover) and be sure
that the LED is not damaged as it enters
the lens assembly.
7. Secure the case front four holes with the
supplied screws. (See figure 4.)
P/N 7-600033 Rev. F
Figure 4
©Honeywell International. All Rights Reserved.
DigiReader DR4220 Installation Notes
RECOMMENDED STAND-OFF PLATE
Material is 3/4” LEXAN®, plywood or equivalent.
LEXAN® is a Registered Trademark of General Electric Corporation.
Honeywell
135 West Forest Hill Avenue
Oak Creek, WI 53154
(414) 766-1700 Ph
(414) 766-1798 Fax
www.honeywell.com
Honeywell – Europe
Boeblingerstrasse 17
71101 Schonaich
Germany
Specifications subject to change without notice.
© Honeywell International. All rights reserved.
Document 7-600033, Revision F

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-702
Modify Date                     : 2006:08:01 18:20:57-04:00
Create Date                     : 2006:05:04 12:04:18-04:00
Metadata Date                   : 2006:08:01 18:20:57-04:00
Creator Tool                    : FrameMaker 6.0
Format                          : application/pdf
Title                           : 7600033D-4220-4-5-02.fm
Document ID                     : uuid:d13de8fa-55f1-42d3-9b9a-9bba921b2f9a
Instance ID                     : uuid:851c58e1-a499-4272-9f42-5bdc690c8c76
Producer                        : Acrobat Distiller 4.05 for Windows
Has XFA                         : No
Page Count                      : 6
Creator                         : Adobe Illustrator(R) 9.0
For                             : Quincie C Butts, Honeywell
Bounding Box                    : 72 24 540 720
Container Version               : 9
Creator Version                 : 9
Image Height                    : 696
Image Width                     : 468
Image Size                      : 468x696
Megapixels                      : 0.326

EXIF Metadata provided by EXIF.tools