Honeywell SP5700 PDA with Bluetooth, WLAN and GSM Modules User Manual
Honeywell International Inc. PDA with Bluetooth, WLAN and GSM Modules
Contents
- 1. Users Manual
- 2. Manual
Users Manual
Revised Version/ March 2007 User Manual OPTIMUS PDA SP5700 SERIES Manual Revised Version October 2006 InnoTeletek, Inc Copyright © 2007 InnoTeletek, Inc. Revised Version/ March 2007 User Manual FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment. FCC Compliance statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Copyright © 2007 InnoTeletek, Inc. FCC RF EXPOSURE INFORMATION WARNING! Read this information before using your phone In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of this phone complies with the FCC guidelines and these international standards. Use only the supplied or an approved antenna. Unauthorized antennas, modifications, or attachments could impair call quality, damage the phone, or result in violation of FCC regulations. Do not use the phone with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Please contact your local dealer for replacement antenna. Body-worn Operation This device was tested for typical body-worn operations with the back of the phone kept 0.59 inches (1.5 cm) from the body. To comply with FCC RF exposure requirements, a minimum separation distance of 0.59 inches (1.5 cm) must be maintained between the user’s body and the back of the phone, including the antenna, whether extended or retracted. Thirdparty belt-clips, holsters and similar accessories should not contain metallic components and must provide 0.59 inch (1.5 cm) separation distance between the user’s body and the back of the phone. Body-worn accessories that do not meet these requirements may not comply with FCC RF exposure limits and should be avoided. For more information about RF exposure, please visit the FCC website at www.fcc.gov Preliminary Version / January 2005 Revised Version/ March 2007 User Manual Contents Notice⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅6 1. MC5000,OPTIMUS PDA SP5700 SERIES – General view ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅9 2. Getting Started ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅10 2.1 Charging the Battery⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅10 2.2 Turning on/off⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅12 3. Settings ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅15 3.1 Sleep Mode ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅15 3.2 LCD Display⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅15 3.3 Volume & Sounds⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅15 3.4 Date/Time ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅15 4. PDA Management ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅16 4.1 Using the Stylus ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅16 4.2 Calibrating the Screen⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅16 4.3 Resetting ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅17 4.3.1 Performing a Soft Reset ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅17 4.3.2 Performing a Hard Reset ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅18 5. Applications ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅19 5.1 Creating Documents ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅19 5.2 Barcode Scanning ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅25 5.2.1 Laser Scan Engine ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅25 5.2.2 Image Scan Engine ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅27 5.3 Connecting with a Desktop ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅29 5.3.1 Installing ActiveSync on a Desktop ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅25 5.3.2 Setting up a partnership⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅25 5.4 Wireless LAN⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅33 5.5 GSM/GPRS ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅36 5.5.1 Initializing the Modem ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅36 5.5.2 Checking Subscriber Identity Module (SIM) ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅38 5.5.3 Menu ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅39 5.5.4 Voice call ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅42 5.5.5 Short Message Service ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅43 5.5.6 Phonebook ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅46 Copyright © 2007 InnoTeletek, Inc. Revised Version/ March 2007 User Manual 5.5.7 History ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅48 5.5.8 Sound Settings ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅49 5.5.9 Setting a Wireless Network ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅50 5.5.10 How to Lock Menu ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅52 5.5.11 Connecting to GPRS Network⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅53 6. Troubleshooting ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅55 7. Specifications ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅57 7.1 Physical characteristics ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅57 7.2 Performance ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅57 8. Limited Warranty Statement ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅58 9. Customer Care Information ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅60 Pictures Picture 1 Front and left side view ..………..…………………………………………...……9 Picture 2 Positioning PDA in the cradle...………………………..……………………..…10 Picture 3 Charging process ...…..…………………………………………………………..11 Picture 4 Battery cover ..……...........……………………………………………………….12 Picture 5 Power button …………………………………………………………………...…13 Picture 6 Desktop background ……………………………………………………………..13 Picture 7 Power setting from the Control Panel…….............................................……14 Picture 8 Calibration screen…………......................................................................….16 Picture 9 Calibration settings completion……........................................................…..17 Picture 10 Power and Enter buttons ……….........................................................…….17 Picture 11 Reset button location………...................................................................….18 Picture 12 WordPad shortcut …….....................................................................………20 Picture 13 New Document display…….................................................................……20 Picture 14 Drop-down menu arrow………..............................................................…..21 Picture 15 Keyboard display…………..........................................................................21 Picture 16 Character recognition Program………........................................................22 Picture 17 Screen boxes recognition.....….............................................................…..23 Picture 18 Full screen recognition modes…….................................................……….23 Picture 19 Split screen mode ……............................................................................…24 Picture 20 Barcode scan application ………............................................................….25 Picture 21 Barcode scanning……….........................................................................…25 Copyright © 2007 InnoTeletek, Inc. Revised Version/ March 2007 User Manual Picture 22 Scanning result ………................................................................................26 Picture 23 Barcode selection list……...........................................................................26 Picture 24 Opening barcode image scanning program ……...............................……..27 Picture 25 Disabling image function …….....................................................................28 Picture 26 ActiveSync 4.1 setup wizard …….......................................................…….29 Picture 27 Connection process …................................................................................30 Picture 28 Partnership set up window .……........................................................……..30 Picture 29 Synchronization options………...........................................................…….31 Picture 30 Setup completion……........................................................................……..31 Picture 31 Synchronization process…….........................................................………..32 Picture 32 Synchronization status .................................................................…………32 Picture 33 Network and Dial-up Connections icon ……….......................................….33 Picture 34 Initializing connection process……......................................................……33 Picture 35 IP address and server address assignation ………...............................…..34 Picture 36 Network connection icon …………….................................................……..35 Picture 37 Connection status……........................................................................…….35 Picture 38 Running DDialer from the desktop………..........................................……..36 Picture 39 Open DDialer display ………...............................................................…….36 Picture 40 Signal strength ………………..............................................................…….37 Picture 41 Connection quality ……………...........................................................……..37 Picture 42 Operating mode ………......................................................................……..37 Picture 43 Request for SIM card insertion ……....................................................…….38 Picture 44 Emergency calls available……...................................................…………..38 Picture 45 Request for PIN ……………................................................................…….38 Picture 46 Entering PIN data ……………............................................................……..38 Picture 47 Display after connecting to a network…................................................…..39 Picture 48 Phone setup options ………................................................................…….40 Picture 49 Sound setup……………………............................................................……40 Picture 50 Network setup……...................................................................…………….40 Picture 51 SMS setup……............................................................................………….40 Picture 52 PIN edit ……………….........................................................................…….40 Picture 53 Version info……………........................................................................……40 Picture 54 User Interface functions …….................................................................…..41 Picture 55 History record …………........................................................................……41 Picture 56 Phonebook …………………...………………………………………………….41 Picture 57 Mailbox………………………………………………………………………...…41 Copyright © 2007 InnoTeletek, Inc. Revised Version/ March 2007 User Manual Picture 58 Touch-screen keypad ....………………………………………………….…….42 Picture 59 Keyboard …………………………………………………………………….…..42 Picture 60 Mailbox display ……………………………………………………………...…..43 Picture 61 Mailbox and SMS windows …………………………………………….………44 Picture 62 SMS encoding program selection……………………………………………..44 Picture 63 Editing text and addressing SMS ...………………………………….………..45 Picture 64 Adding a new contact ……………………………………………………..……46 Picture 65 Phonebook content ………………………………………….……………….…46 Picture 66 Management of phonebook numbers ………………………………….……..47 Picture 67 Tracking history records ……......................................................................48 Picture 68 Sound configurations…………....................................................................49 Picture 69 Network advanced settings …................................................................….50 Picture 70 Connection to network using manual mode……....................................….51 Picture 71 Locking menu values ……………...........................................................….52 Picture 72 Settings on the Start Menu ……….....................................................……..53 Picture 73 Network Connections tab ….............................................................………53 Picture 74 GPRS icon ….........................................................................................…..54 Picture 75 Dial-up connection window ...................................................................…..54 Tables Table 1 Solving problems ........................................................................................55/56 Table 2 Physical specifications .....................................................................................57 Table 3 Hardware specifications...................................................................................57 Copyright © 2007 InnoTeletek, Inc. Revised Version/ March 2007 User Manual Notice 1. Limited Warranty InnoTeletek will repair the defective parts free of charge if the problem is due to materials or workmanship during the warranty period. The warranty period for this product is one year from the date of product purchase. Provided that the date of purchase is not clear, it is six months from the date of manufacture. The warranty period for the battery is six months from the date of product purchase. Provided that the date of purchase is not clear, it is three months from the date of manufacture. However, InnoTeletek does not service free of charge in case of noted below even during the warranty period. Any damages or defectives: (1) as a result of accident, misuse, abuse, or other external causes; (2) by the reason of flood, typhoon, fire, war or other Acts of God; (3) by the user’s arbitrary modification or conversion; (4) by any other reasons beyond defects of materials or workmanship. 2. Certifications This product has been approved by Ministry of Information and Communication. EMC (EMI/EMS): MIC, FCC part 15 class B, EU EMC directive 3. Copyrights This manual describes and explains the product on the basis of the time of present. InnoTeletek IS NOT LIABLE FOR ANY LOST PROFITS CAUSED BY UNEXPECTED RESULTS CONCERNED WITH OMISSIONS AND THE EDITING OF THIS MANUAL. THE MATERIAL IN THIS MANUAL IS SUBJET TO CHANGE TO IMPROVE RELIABILITY, FUNCION, OR DESIGN WITHOUT NOTICE. The law protects all programs and the rights. Without the permission from InnoTeletek, no right to copy, quote or translate this manual in whole or in part is granted except as permitted under copyright law. Other product names mentioned in this manual such as Microsoft ActiveSync®, Windows® and its logo are registered trademarks of their companies. InnoTeletek is permitted to use those Microsoft products by an affiliate of Microsoft, Microsoft Licensing, Inc. All software furnished to the user is on a licensed basis, and it is not sold. InnoTeletek has the rights of all software, and it grants to the user a license to use the software. The rights of software are granted to the user under the agreement to comply with the terms on the license agreement. Such license should not be sublicensed, distributed or transferred to other persons by the user. InnoTeletek License Agreement applies to all software provided by InnoTeletek. Microsoft programs are granted to use by its End User License Agreement (EULA). The user shall not modify or merge any form of a licensed program with other programs, or use it in a network without prior consent of InnoTeletek. No right to copy a licensed program in whole or in part is granted except as permitted under copyright law. Copyright © 2007 InnoTeletek, Inc. Revised Version/ March 2007 InnoTeletek may terminate the contract in the breach of contract by the user. User Manual 4. Precautions 1) Use this product at a proper voltage. Otherwise, this product may be damaged or cause a fire. 2) Do not dismantle or modify this product arbitrarily. It may cause malfunction or damage, and the warranty does not apply to these cases. 3) Do not use this product in dusty and humid places. It may weaken the function or cause malfunction of the product. 4) When using the product, keep it away from magnetic fields or large loudspeakers. Otherwise, it may erase data stored in the terminal’s memory or cause damage to the LCD. 5) Be careful not to expose your eyes to the laser beam while scanning. It is harmful for your eyes. 6) Optional CDMA embedded products have their own Electronic Serial Numbers (ESN) in the built-in CDMA Module. Do not copy or modify ESN illegally. Otherwise, a legal restraint will be taken. 5. Tips for MC5000,OPTIMUS PDA SP5700 SERIES trouble-free usage 1) MC5000,OPTIMUS PDA SP5700 SERIES is designed to operate between -20℃~ 60℃. Therefore protect your terminal from temperature extremes. Do not leave it on the dashboard of a car on a hot day, and keep it away from heat sources. Otherwise, it may cause malfunction, or data stored in your terminal may be lost. 2) The PDA is durably made to withstand the 1.5m dropping test. The touch-sensitive screen of PDA is made of glass. Therefore, avoid dropping your terminal or expose screen display to strong impacts. Otherwise, it may be damaged. 3) Although MC5000,OPTIMUS PDA SP5700 SERIES is water resistant, do not expose it to rain or moisture for an extended period of time. Avoid using the terminal when it rains heavily. Wipe the water on the terminal with a soft cloth when it is moist before using. Otherwise, it may cause malfunction. 4) Do not scratch the screen. Use provided stylus pen only, which is intended for use with a touch-screen. Never use other pens, pencils or sharp objects for pointing on the screen. Clean the screen with a soft, wet cloth when it is covered by dust. Not removing it regularly may cause damages to the touch-screen. 5) Do not use your industrial PDA in the proximity of signal emitting electronic appliances. Radio waves of emitted by electronic devices may disturb correct functioning of MC5000,OPTIMUS PDA SP5700 SERIES . It is also recommended not store or use your terminal in an environment that is extremely dusty, damp or wet. Copyright © 2007 InnoTeletek, Inc. Revised Version/ March 2007 User Manual 6. Unpacking Carefully remove protective materials from the PDA and the cradle, and store the shipping cartons for packing to ship after reparation or return. Verify that you have received all equipment as enlisted below. The terminal box should contain: - TERMINAL: 1 - LITHIUM-ION BATTERY: 1 - HANDSTRAP: 1* - TERMINAL CASE: 1* - STYLUS: 1* The cradle box should contain (optional): - ONE-SLOT CRADLE: 1 - USB SYNCH CABLE: 1 - ADAPTER: 1 - POWER CORD: 1 * In plastic bag In case when there are damaged units or missed parts, call the local agent or distributor immediately. If the problem cannot be solved instantly, you should return the PDA to the local agent or distributor. However, InnoTeletek is not liable for any damages that occurred due to mishandling during transportation or when the shipping package is not used. For more details with this regard refer to the “Service Information” on page 35. Copyright © 2007 InnoTeletek, Inc. Revised Version/ March 2007 User Manual 1. MC5000,OPTIMUS PDA SP5700 SERIES view Picture 1 Front and left side view 1. Indicator LED (Charging & Operation) 2. Antenna (for Wi-Fi & GSM) 3. USB Host connector 4. Speaker 5. Scan Trigger 6. 4 Way Navigation Pad 7. Power Button 8. Send & End Buttons for WWAN 9. Numeric Key Pad 10. Keypad Backlight Button Copyright © 2007 InnoTeletek, Inc. 10 – General Revised Version/ March 2007 User Manual 11. Function Key 12. Universal I/O connector 2. Getting Started 2.1 Charging the Battery Before using the PDA for the first time, recharge the Li-ion Battery. When charging is completed indicating LED turns GREEN. It usually takes approximately 3 hours. Now, given this information place your MC5000,OPTIMUS PDA SP5700 SERIES into the cradle and charge it. Note: When you are going to charge the PDA for the first time, do not you remove the battery before it is fully charged as it may cause malfunction. To ensure the quickest recharge time, turn the PDA into a sleep mode. To charge the battery: ① Connect the cradle to the power supply source. ② Slide your PDA into the cradle until red LED lights up. To charge spare battery, insert the battery into the slot at the top of the cradle. The charger starts operating automatically, and completes charging in within 3 hours. Picture 2 Positioning PDA in the cradle Copyright © 2007 InnoTeletek, Inc. 11 Revised Version/ March 2007 User Manual ③ When LED turns RED it indicates that the battery is charging status. As the process is completed, LED changes into GREEN. Picture 3 Charging process Note: MC5000,OPTIMUS PDA SP5700 SERIES is equipped with a memory backup battery. The backup battery allows storing data in memory when the main battery is removed or discharged. If the PDA remains without the main battery for more than 1 hour, the backup battery discharges. It is highly recommended to replace the main battery within 10 minutes or keep charging the battery when the PDA is inserted in the cradle. Otherwise your data may be lost. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE NATIONAL CODE OR RECYCLING PROGRAM 2.2 Turning on/off 1) When you are replacing the batteries for the first time ① Pull out the rubber latch from the cover’s slot. ② Slide the cover left. Copyright © 2007 InnoTeletek, Inc. 12 Revised Version/ March 2007 User Manual Picture 4 Battery cover ② Insert the battery in the compartment in accordance with its correct positioning. Ensure that the top of the battery adhere to the place first, and then you can fix its bottom. To close the compartment, slide the cover on the right direction and lock the hook. Copyright © 2007 InnoTeletek, Inc. 13 Revised Version/ March 2007 User Manual 2) How to use the power button to turn on your MC5000,OPTIMUS PDA SP5700 SERIES ① Press the Power button to turn the PDA on. - If you press and then hold the Power button for about 3 seconds, PDA switches into sleep mode and turns off. Picture 5 Power button ② When the booting process is finished, Windows® logo will be displayed on a desktop as illustrated below. Picture 6 Desktop background ③ If the Power button does not activate your PDA, you should execute a hard reset. For Copyright © 2007 InnoTeletek, Inc. 14 Revised Version/ March 2007 User Manual details refer to the section “Performing a Hard Reset.” 3) Turning off your MC5000,OPTIMUS PDA SP5700 SERIES ① Press and hold the Power button for 3 seconds or tap Suspend on the start menu. - It is possible to set your terminal to auto-suspend status or to auto-turn off after specified period of time what will allow you to save the battery’s power. - Power setting method: Tap Start → Settings → Control Panel. Double tap the Power button and select Schemes Tab. Picture 7 Power setting from the control panel ② It is recommended to remove the battery from the PDA when it is not in use for a long time. Copyright © 2007 InnoTeletek, Inc. 15 Revised Version/ March 2007 User Manual 3. Settings 3.1 Sleep Mode 1) To reduce energy consumption, push the Power button for 3 seconds or tap Start → Suspend, and your terminal will switch into a sleep mode. Data stored in RAM remains unchanged when turning into sleep mode. 2) To wake up from sleep mode, press the Power button. When the system wakes up, the screen will display the same view displayed before sleep mode. 3.2 LCD Display 1) To save battery power it is recommended to change the backlight settings. Tap Start → Settings → Control Panel, then Double tap Display. 2) Press Backlight tab and select required option. 3.3 Volume & Sounds To change sounds and the volume tap Start → Settings → Control Panel, then double tap Volume & Sounds icon. 3.4 Date/Time In order to adjust the date and time, select Start → Settings → Control Panel, then double tap on the Date/Time icon. Copyright © 2007 InnoTeletek, Inc. 16 Revised Version/ March 2007 User Manual 4. PDA Management 4.1 Using the Stylus The stylus is useful for command selection and entering data. The stylus functions are similar a mouse connected to PC. 1) Tap: Touch the screen once with the stylus to open an item and select options. 2) Drag: Hold the stylus on the icon and drag it across the screen to selected area. Drag in a list to select multiple items. Note: 1. If the surface of the display becomes dirty, clean it with a soft cloth before using the stylus pen. 2. Take care not to scratch the screen. When working MC5000,OPTIMUS PDA SP5700 SERIES , use only the provided stylus that is intended for use with the PDA touch-screen. Never use a pen, pencil or other sharp pointers on the surface of the MC5000,OPTIMUS PDA SP5700 SERIES screen. 3. Do not let children to play with the stylus. Contact with the end edge may cause injury. Please keep the PDA away from children. 4.2 Calibrating the Screen When you tap with the stylus and programs or functions are not activated correctly, you should calibrate the screen. Calibration allows aligning the cursor on the touch-screen. The method is as follows: 1) To calibrate your screen, select Start → Settings → Control Panel, next double tap the Stylus icon, then indicate Calibration tab→ Recalibrate button. 2) Take the stylus from its holder on the back of the terminal. 3) Tap the center of the cross mark that appears on the screen with stylus. Picture 8 Calibration screen Copyright © 2007 InnoTeletek, Inc. Picture 9 Calibration settings completion 17 Revised Version/ March 2007 User Manual 4.3 Resetting If the screen freezes or the terminal becomes inoperative, you may need to reset your PDA. 4.3.1 Performing a Soft Reset Note: Transfer all stored data into a computer otherwise files that are open during a soft reset may not be retrieved. To perform a hard reset, press Reset Button located on the right side above the Battery Cover. Picture 10 Reset buttons Press the Reset Button here by using your stylus Note: Soft reset restarts MC5000,OPTIMUS PDA SP5700 SERIES and saves all stored records. 4.3.2 Performing a Hard Reset By executing hard reset formats, preferences, date/time, and other settings are restored to their factory default values. To perform a soft reset, press reset button simultaneously the Power and Reset buttons. Picture 11 Power & Reset button Copyright © 2007 InnoTeletek, Inc. 18 Revised Version/ March 2007 User Manual Note: Hard reset not only restarts your PDA, but also erases all stored records and entries in RAM. Therefore, perform a hard reset only in cases when a soft reset mode does not work. BE CAREFUL WHEN YOU PERFORM A HARD RESET SEVERAL TIMES CONSECUTIVELY WITHIN SHORT PERIOD OF TIME, IT MAY CAUSE THE SCREEN TO BECOME BLANK ACCOMANIED BY VERTICAL LINES DISPLAY ON IT. Copyright © 2007 InnoTeletek, Inc. 19 Revised Version/ March 2007 User Manual 5. Applications 5.1 Creating documents You can create a new document on your PDA with Microsoft WordPad® , or work on an existing one by sending it from the PC to your MC5000,OPTIMUS PDA SP5700 SERIES . Data, files, and document uploads/downloads between PDA and computer are controlled by the Microsoft ActiveSync® software. There are two ways to enter characters into the document using document-editing programs: - Using the keyboard - Using the handwriting recognition program. Detailed method for making documents with each of the above mentioned methods are as follows: Microsoft WordPad® is a registered trademark of Microsoft. Copyright © 2007 InnoTeletek, Inc. 20 Revised Version/ March 2007 User Manual 1) Using the keyboard ① Tapping on the WordPad icon from the Start menu or on the shortcut from the screen, runs Microsoft WordPad®, the document-editing program. The below illustrated pictures demonstrate how to use the screen shortcut for activating WordPad. By double tapping on the Microsoft WordPad® icon (Picture 12), the display of opened Microsoft WordPad® processor will appear (Picture 13). Picture 12 WordPad shortcut Copyright © 2007 InnoTeletek, Inc. Picture 13 New Document display 21 Revised Version/ March 2007 User Manual ② Tap on at the bottom of the screen as it is shown on the Picture 14. Next the drop- down menu will appear. Then select Keyboard (Picture 15). Picture 14 Keyboard Icon Picture 15 Keyboard Panel ③ When the keyboard display appears on the lower part of the screen, tap the buttons with characters to enter text into your document. Note: You can also use the PDA’s keypad to input characters. The keypad is a numeric so that also recognizes the numbers (0~9). The keypad is color-coded to indicate particular actions that are taken when the Shift key is being pressed. Copyright © 2007 InnoTeletek, Inc. 22 Revised Version/ March 2007 User Manual 2) Using the character recognition program ① Open Microsoft WordPad®, the document-editing program. ② Tap on the icon located at the bottom of the screen. Then options will appear. Select Picture 16 Character recognition program selection Copyright © 2007 InnoTeletek, Inc. 23 Revised Version/ March 2007 User Manual ③ Press shaped button one more time. A window with the options appears on the lower part of the screen. Upper case, lower case, and numbers/symbols should be written in a certain fields marked by “a”, “A” and “1·@” – symbols that reflect three different character recognition modes. Space Tab Enter Back Space Picture 17 Screen boxes recognition Mode Conversion Input Ctrl: A shortcut key applied with “Ctrl + character” e.g. writing S in the Ctrl field calls the save file dialogue box in the same way as in case of pressing simultaneously Ctrl+S for the keyboard. ④ To display full screen mode for writing, tap on the - shaped button located on the right side of the application (circled area on the Picture 17). Then, if you write letters using your stylus, they will be converted into a text on the top of the screen. Copyright © 2007 InnoTeletek, Inc. 24 Revised Version/ March 2007 User Manual Picture 18 Full screen recognition mode ⑤ In order to split window, tap the Picture 19 Split screen mode - shaped button on the bottom menu bar at the full screen mode. Now, upper part of the display located above the red arrows (circled in blue on the picture below) is for capital letters input space and the lower part of the screen is designated for small letters input. Copyright © 2007 InnoTeletek, Inc. 25 Revised Version/ March 2007 User Manual 5.2 Barcode Scanning 5.2.1 Laser Scan Engine 1) Open the barcode scanning program from the shortcut on the screen. Picture 20 Barcode scan Test 2) Place the scanner in alignment to the direction of a barcode and press one of trigger buttons. Let RED laser beam line cover the barcode. DO NOT KEEP THE SCAN BUTTON PRESSED TOO LONG; IT MAY RESULT IN SCAN ENGINE FAILURE OR MALFUNCTIONING. Picture 21 Barcode scanning Copyright © 2007 InnoTeletek, Inc. 26 Revised Version/ March 2007 User Manual 3) A short beep sound indicates successful accomplishment of decoding and the result will be displayed in the scan window. Picture 22 Scanning result Picture 23 Barcode selection list 4) In order to accelerate decoding process, you can disable imaging. Click Options button from the menu bar and unmark the Enable Image command. 5) Readable codes Linear Symbologies: Codabar, Code 11, Code 128, Code 39, Code 93, EAN-8, EAN-13, Interleaved 2 of 5, ISBT 128, MSI, Reduced Space Symbology, Straight 2 of 5 IATA, UPC-A, UPC-E, UPC-E1 Copyright © 2007 InnoTeletek, Inc. 27 Revised Version/ March 2007 User Manual 5.2.2 Image Scan Engine 1) Run the barcode image scanning program by tapping a shortcut on the background screen. Picture 24 Opening barcode image scan program 2) Place the PDA’s scanner in aligned with a barcode position and press one of trigger buttons. Let Green laser beam line cover the barcode. DO NOT KEEP THE SCAN BUTTON PRESSED TOO LONG; IT MAY RESULT IN SCAN FAILURE OR DEVICE MALFUNCTION. 3) A short beep will indicate successful decoding. And the result will be displayed appears in the scan window. 4) In order to accelerate decoding process, disable imaging by using the Option menu. Using stylus, tap on the Option tab from and then unmark the Enable Image on the drop down list. Copyright © 2007 InnoTeletek, Inc. 28 Revised Version/ March 2007 User Manual Picture 25 Disabling image function 5) Readable codes Linear Symbologies: Codabar, Code 11, Code 128, Code 39, Code 93, EAN-8, EAN-13, Interleaved 2 of 5, ISBT 128, MSI, Reduced Space Symbology, Straight 2 of 5 IATA, UPC-A, UPC-E, UPC-E1 Stacked Symbologies: Codablock F, Code 49, EAN·UCC Composite, Micro PDF417, PDF 417, TCIF Linked Code 39 (TLC39) 2D Matrix Symbologies: Aztec Code, Aztec Mesa, Data Matrix, MaxiCode, QR Code Postal Symbologies: Australian Post, British Post, Canadian Post, Japanese Post, KIX (Netherlands) Post, Planet Code, Postnet, OCR Fonts: OCR US Money Font Copyright © 2007 InnoTeletek, Inc. 29 Revised Version/ March 2007 User Manual 5.3 Connecting with a Desktop ActiveSync® is the software that allows users to move files, update message contents, and address book between desktop and MC5000,OPTIMUS PDA SP5700 SERIES . When the PDA’s cradle and desktop computer are connected with USB cable, insertion of your MC5000,OPTIMUS PDA SP5700 SERIES into the cradle activates a Microsoft ActiveSync window, which appears on the desktop and indicates the synchronization status. 5.3.1 Installing ActiveSync® on a Desktop ① Insert the ActiveSync CD in the CD-ROM drive. The installation manager will lead you quickly through the installation process. You can also download the latest version of the software from Microsoft Corporation website at http://www.microsoft.com Picture 26 ActiveSync 4.1 setup wizard ② If the auto installation screen does not appear, click on the setup.exe file on the accompanied CD-ROM. Copyright © 2007 InnoTeletek, Inc. 30 Revised Version/ March 2007 User Manual 5.3.2 Setting up a partnership ① Insert your MC5000,OPTIMUS PDA SP5700 SERIES in the cradle, which is connected to the desktop computer by a USB or RS232 cable. Then the screen will display a window indicating that the PDA is being connected. Picture 27 Connection process ② The desktop computer and your PDA will attempt to synchronize. As a result the partnership window appears. Tap on Yes button and then select Next. Picture 28 Partnership set up window Copyright © 2007 InnoTeletek, Inc. 31 Revised Version/ March 2007 User Manual ③ The Select Synchronization Settings Window appears. Here, select the items you want to synchronize, and then press the Next button. Picture 29 Synchronization options ④ To complete the process select the Finish button. Then the basic settings and configuration for a PC and the PDA connection will be established. Picture 30 Setup completion Copyright © 2007 InnoTeletek, Inc. 32 Revised Version/ March 2007 User Manual ⑤ Go through the earlier steps to run ActiveSync®. Picture 31 Synchronization process ⑥ At the end, the window informs that synchronization has been successfully completed. Copyright © 2007 InnoTeletek, Inc. 33 Revised Version/ March 2007 User Manual Picture 32 Synchronization status 5.4 Wireless LAN With a wireless LAN type model, you can log into the Internet wirelessly through the internal WLAN card. However, your PDA must be set up in accordance with the equipment specification (including Hotspot) that is required to access the wireless LAN. To meet these needs MC5000,OPTIMUS PDA SP5700 SERIES must be properly configured. ① Select Start → Settings → Control Panel, and then double tap Network and Dial-up Connections icon. Picture 33 Network and Dial-up Connections icon ② Select an appropriate driver to add the Wireless LAN card. Picture 34 Initializing connection process Copyright © 2007 InnoTeletek, Inc. 34 Revised Version/ March 2007 User Manual Note: Driver types may vary depending on applied wireless LAN card. Therefore, you should check your driver characteristics before attempting to activate connection. ③ Dynamic IP Select Obtain an IP address via DHCP server. In this case the wireless communication is not available because DHCP server does not assign static IP addresses. ④ Static IP i) Select Start → Settings → Control Panel, then double tap Network and Dial-up Connections. ii) Select relevant driver to add Wireless LAN card. For example, this unit is equipped with CISCO product. iii) Select the IP Address tab, and then point one the Specify an IP address radio button. Enter the IP Address, Subnet Mask and Default Gateway data. iv) Press the Name Servers tab, and enter required data. Consult the network manager for providing necessary data. Picture 35 IP address and server address assignation Copyright © 2007 InnoTeletek, Inc. 35 Revised Version/ March 2007 User Manual * To check your network connection status, select the icon on the Taskbar, and then click on the Wireless Information tab. The Signal Strength is indicated as Very Good or Good etc… Picture 36 Network connection icon Picture 37 Connection status v) Select the IP Information tab, and make sure that the static IP address data has been entered correctly. Note: The IP address data is not lost when a soft reset is performed. However, it should be reentered again, if a hard reset has been executed. Copyright © 2007 InnoTeletek, Inc. 36 Revised Version/ March 2007 User Manual 5.5 GSM / GPRS In general GPRS module works as a mobile data service to users of GSM mobile devices of 2.5G and provides moderate speed data transfer, by using TDMA channels in GSM network. In order to set up a GPRS connection, a user needs to specify Access Point Name (APN), user name and password, and very often IP address, all provided by the network operator. 5.5.1 Initializing the Modem Picture 38 Running DDialer from the desktop Picture 39 Open DDialer display ① When PDA startup, the DDialer is activated automatically and initializes GSM Module When initialization is under process you can observe the following icons in the Taskbar: : Modem suspended : Modem activation in progress : SIM card information is being loaded Copyright © 2007 InnoTeletek, Inc. 37 Revised Version/ March 2007 User Manual Picture 40 Signal strength Picture 41 Connection quality ② Antenna and signal icon indicates GSM or DCS signal strength as follows: : Found signals only : Found signals and identified an operator : Service area not available Picture 42 Operating mode You can switch on/off GSM module by pressing “END” button on the screen for a while. After turning GSM function off, you will notice a display of “Modem Off” message. Copyright © 2007 InnoTeletek, Inc. 38 Revised Version/ March 2007 User Manual 5.5.2 Checking Subscriber Identity Module (SIM) As soon as the Phone User Interface starts, the program checks stored SIM data. The SIM card requires PIN information and to enter it you should precede in accordance with the method depicted on the Pictures 45 and 46. Picture 43 Request for SIM card insertion Picture 45 Request for PIN Copyright © 2007 InnoTeletek, Inc. Picture 44 Availability of emergency calls Picture 46 Entering PIN data 39 Revised Version/ March 2007 User Manual 5.5.3 Menu Picture 47 Display after connecting to a network ① Battery information ( Empty : ② Ear volume status ( Min : Low : , Mid : Mid : , Max : Full : ③ SMS memory status No unread messages : Single unread message : Many unread messages : SIM card is full (or in test mode ): ④ UI lock indicator ⑤ Mode status ⑥ UI Menu : Phonebook / History / Message selection ⑦ Phone setting menu : Sound, Network, Version, Message, Locking (PIN), Menu Setting ⑧ Display window status ⑨ Modem status / Signal strength ⑩ Keyboard icon Copyright © 2007 InnoTeletek, Inc. 40 Revised Version/ March 2007 User Manual 1) Phone Setting Menu Picture 48 Phone setup options 2) Setup options By tapping items from Phone Setting Menu, you can open sound, network, SMS, lock, and version info setup windows. Picture 49 Sound setup Copyright © 2007 InnoTeletek, Inc. Picture 50 Network setup 41 Picture 51 SMS setup Revised Version/ March 2007 User Manual Picture 52 PIN edit Picture 53 Version info 3) User Interface Menu To change phonebook, check out history, and mailbox settings, tap on selected item on UI menu drop-down list. Picture 54 User Interface functions Picture 55 History record Picture 56 Phonebook Picture 57 Mailbox A) Call Log: Views call log and history B) Phone Book: Displays list of callers and along with their names and respective phone numbers Copyright © 2007 InnoTeletek, Inc. 42 Revised Version/ March 2007 User Manual C) Mail Box: Checks SMS box 5.5.4 Voice call 4.1 Voice Dialing/Getting If you want to make a call you should use the key pad or LCD touch-screen driven panel. Picture 58 Touch-screen keypad 4) Voice call : Use the keypad (Send/End, number keys) or touch-screen LCD 5) Volume control : Navigate through the 4-way direction key pad (Up/Down) Picture 59 Keyboard Copyright © 2007 InnoTeletek, Inc. 43 Revised Version/ March 2007 User Manual 5.5.5 Short Message Service Reading Stored SMS texts Stored Message List Unread message Read message Sent message Encoding types 7 bit / 8 bit / UCS2 Phone number field Message forwarding button Picture 60 Mailbox display Copyright © 2007 InnoTeletek, Inc. 44 Revised Version/ March 2007 User Manual Sending a Message Delete message icon Picture 61 Mailbox and SMS windows ⑪ Tap on the icon to write a message ⑫ In the Blue Box, write a message by using Character recognition program or PDA’s keypad ⑬ Press Send Message button to initiate transmission process ⑭ Select an appropriate encoding program. Among SMS encoding options are: 7bit standard, 8bit standard, and UCS2 (Unicode16). Copyright © 2007 InnoTeletek, Inc. 45 Revised Version/ March 2007 User Manual Picture 62 SMS encoding program selection After writing a message, send SMS text by pressing the ‘Send’ button The button displays address book’s contents The ‘Char’ button displays GSM 7bit Character and symbol list Picture 63 Editing text and addressing SMS Copyright © 2007 InnoTeletek, Inc. 46 Revised Version/ March 2007 User Manual 5.5.6 Phonebook How to Add a New Phone Number Picture 64 Adding a new contact ⑮ Tap on the icon to add a new address 16 Enter phone number and other information into the “Address Detail” window 17 Specify a “Quick Dial” number, or select primary phone number among cellular, home and office phones viewing the whole list Slide for Up/Down Picture 65 Phonebook content Copyright © 2007 InnoTeletek, Inc. 47 Revised Version/ March 2007 User Manual Updating Phone Numbers Update Changes Delete Phone Number Dial to: Send SMS to: Picture 66 Management of phonebook numbers ① Edit PhoneBook ② Select phone number ③ When the “Address Detail” screen appears, update phone number information, delete selected item, or save changes by tapping the Copyright © 2007 InnoTeletek, Inc. 48 icon Revised Version/ March 2007 User Manual 5.5.7 History This button deletes history record Missed call Sent call Received call Save to the PhoneBook Delete indicated items Picture 67 Tracking history records Copyright © 2007 InnoTeletek, Inc. 49 Revised Version/ March 2007 User Manual 5.5.8 Sound Settings Picture 68 Sound configurations Thanks to this screen configuration tools you can change Ring Sound / Message Notification Sound / Connect HO Sound and Network Register Sound / Hang-Up and Network Unregister Sound, and other volume parameters. Copyright © 2007 InnoTeletek, Inc. 50 Revised Version/ March 2007 User Manual 5.5.9 Setting a Wireless Network Operator (PLMN) Automatic Selection, is set up as default Access Point Name for GPRS When filling in this field, you will set a name for PhoneUI front screen. Select Network Menu In this example, we use for “InnoTeletek” PhoneUI Picture 69 Network advanced settings Copyright © 2007 InnoTeletek, Inc. 51 Revised Version/ March 2007 User Manual By selecting manual Operator mode, the system will be searching operators While pointing at Display by MCC/MNC Number’, you will see the MCC/MNC value. Highlighted icon indicates status of the operators Unknown Available Connected Forbidden Picture 70 Connecting to network in manual mode Copyright © 2007 InnoTeletek, Inc. 52 Revised Version/ March 2007 User Manual 5.5.10 How to Lock the Menu 1. Input your PIN number 2. Select PIN option (check box) 3. Press tab ‘Input PIN information’ If you selected ‘Change PIN Number option Select PIN option (check box) Picture 71 Locking menu values Copyright © 2007 InnoTeletek, Inc. 53 Revised Version/ March 2007 User Manual 5.5.11 Connecting to GPRS Network To establish a new GPRS network, you should set the Access Point Name (APN) first. After having it done press APN press APN Set and Save icon. Picture 72 Settings tab on the Start Menu Copyright © 2007 InnoTeletek, Inc. Picture 73 Network Connections tab 54 Revised Version/ March 2007 User Manual Picture 74 GPRS icon Picture 75 Dial-up connection window Then run the GPRS connecting program according to the following method: Tap Start → Settings → Network and Dial-up Connections. Double tap the GPRS button and press Connect tab. Copyright © 2007 InnoTeletek, Inc. 55 Revised Version/ March 2007 User Manual 6. Troubleshooting Problem OS is not loading Cause Low-Battery Problem with button’s rubber Reset Battery malfunction PDA turns itself off OPTIMUS_PDA is inactive (Sleep Mode) Battery failure Battery does not charge Characters on display are invisible Device was removed from cradle while battery was charging I/O connector is not Clean up the I/O connector. clean PDA is not powered on Press the Power button. Battery is not charged IP error Communication failure with IrDA printer IP crash The stylus pen does not tap correctly Solution Charge or replace the battery. If reset rubber can be pressed with your finger, then cut the tip of the rubber. Take out the battery from the compartment, and press the reset button. Then insert back the battery into the PDA. Press the Power button, then the windows restores. Your PDA becomes idle after some time of inactivity. User Idle switch state can be set on the Power Properties window. Tap Start → Settings → Control Panel → Power. Replace battery. If your terminal still does not operate, try a hard reset. Insert your PDA into the cradle and start charging. Assure that your terminal is turned off, or in a sleep mode while being charged. Shortcut icons does not activate the corresponding function Charge the battery. Fix the static IP address. Check whether more than two users work under the same static IP address. Select Start → Settings and double tap on Stylus. Then recalibrate the stylus. Too many files stored in Delete unused files or transfer data to your PC. memory module A message appears stating that your PDAs memory is fully occupied Copyright © 2007 InnoTeletek, Inc. Adjust the memory allocation. Tap Start → Settings → Control Panel, then double tap the Memory setting problem System tab. Select Memory and adjust the slider. If you have installed new applications on your PDA, remove unused applications to extend Too many applications memory capacity. Tap `4 are installed on your Start → Settings → Control Panel, and Optimus_PDA double tap on Remove Programs. Then select useless programs and tap on Remove button. 56 Revised Version/ March 2007 User Manual Problem Your PDA does not accept scan data input ActiveSync does not operate Sound is not audible Program does not recognize handwriting Cause Solution Scan window is dirty Clean scanner window with a soft, wet cloth. Object moves while Fix the object while scanning. scanning Tap on Start, then Settings → Control Panel, Scanning application is and select the System tab to verify whether the improperly opened unit is loaded with a scanning application or not. Unreadable barcode Scan engine can not read damaged barcodes. Distance between your Adjust the distance between them at terminal and the object is approximately 6 inches, and try again. both; too far or too close PDA is not programmed Check whether your PDA is programmed to read for the barcode the type of barcode you are scanning. Scanning beam not Angle the barcode at 45 degrees or place scan aligned with a barcode beam against a barcode to use direct rays. OPTIMUS_PDA was removed from cradle Insert you PDA into the cradle again. during communication process con- Verify cable genuineness, and check the status of connection. ActiveSync is incorrectly Install the ActiveSync program again. installed or configured Connected as a Guest, Take the terminal out, then insert it the cradle not by previously created again and enter your name again. name Check the volume slider in Volume & Sounds Volume level is very low (Tap on Start → Settings → Control Panel) to or turned off ensure the volume is at adequate level. Dust fills the speaker Clean up the speaker. Incorrect figuration Characters incorrectly cable are written To recognize handwriting input, characters must be written carefully, in a certain way. Character strokes are written on the wrong part Fix the letter recognizer. of the LCD Table 1 Solving problems Copyright © 2007 InnoTeletek, Inc. 57 Revised Version/ March 2007 User Manual 7. Specifications 7.1 Physical Characteristics Dimensions* Weight * Drop Specification Operating Temperature Storage Temperature Environmental Sealing Humidity Electrostatic Discharge (ESD) Key Pad 78 W × 177 L × 34 H (Top); 26 H (Bottom) mm / 3.1 x 7.0 x 1.3 x 1.0 in. 256g / 9.03oz. (WLAN, WPAN, Camera, Scanner Included/ Except Battery) 1.5m / 5 ft onto Concrete Surface (Double Drop for Every Side) -20 ° to 50 °C (-4 ° to 122 °F) -30 ° to 70 °C (-22 ° to 158 °F) IP54 (Dust and Water Splash Protected) 5% to 95% RH Non-condensing 8KVDC/Air, 4KVDC/Contact 2 Triggers, Power, Backlight (LED Backlight Supported), Start, End, 4 Way Navigation Pad, Shift, Function, Backspace, Enter, 12 User-selectable Keys (Numeric, English/ Korean) Table 2 Physical specifications * Subject to change without prior notice. 7.2 Performance CPU Operating System Memory (ROM/RAM) Display Standard Communications Sound (MIC and Speaker) Expansion Slot Radio Capacity Barcode Scanner SW Application Development Battery Intel XScale PXA270 microprocessor (520MHz) Microsoft Windows CETM5.0 - Flash ROM: 128 MB - SDRAM: 128 MB - 3.5" TFT Color LCD (Transflective Type) - Resolution: 240 x 320 pixels RS232, USB v1.1(Host, Client), IrDA v1.2 Water-proof, Internal Microphone and Speaker for Voice Recorder Mini SD card slot - WWAN: CDMA(EVDO)(Optional), GSM/GPRS (Optional) - WLAN: IEEE802.11b/g (Up to 11Mbps/54Mbps) (Optional) 1D Barcode: UPC/EAN/KAN, Code 39/ 93/ 128, Interleaved 2 of 5, etc. 2D Barcode: PDF417, QR Code, Data Matrix, Maxi Code, etc. - Desktop device manager: Microsoft® ActiveSync - Microsoft Windows CE SDK, InnoTeletek SDK Main Battery Rechargeable Li-Ion Battery (3.7VDC, 2000mAh) Back-up Rechargeable Battery Battery (3.7V, 130mAh) Battery Life 3 - 72 hours Charge Time Less then 3 Hours Table 3 Hardware specifications Copyright © 2007 InnoTeletek, Inc. 58 Revised Version/ March 2007 User Manual 8. Limited Warranty Statement documentation that shipped with the product; (c) by the use of parts not manufactured or sold by InnoTeletek; or (d) by modification or service by anyone other than (i) InnoTeletek, (ii) a General This Limited Warranty applies to the InnoTeletek brand name products sold with this Limited Warranty Statement. InnoTeletek authorized service provider or (iii) your own installation of end-user replaceable parts if available for your product in the servicing country. This Limited Warranty may be enforced in any country where InnoTeletek or its authorized service providers offer warranty service subject to the terms and conditions set forth in this Limited Warranty Statement. However, warranty service availability and response times may vary from country to country and may also be subject to registration requirements in the country of purchase. Limitation of Liability InnoTeletek is not liable for any damages caused by the product or the failure of the product to perform, including any lost profits, lost savings, incidental damages, or consequential damages. InnoTeletek is not liable for any claim made by a third party or made by you for a third party. InnoTeletek warrants that the InnoTeletek product you have purchased from InnoTeletek or from an InnoTeletek authorized reseller is free from defects in materials and or workmanship under normal use during the warranty period. This limitation applies whether damages are sought, or a claim made, under this Limited Warranty or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation can not be waived or amended by any person. This limitation of liability will be effective even if you have advised InnoTeletek or an authorized representative of InnoTeletek of the possibility of any such damages. This limitation of liability, however, will not apply to claims for personal injury. The warranty period starts on the date of purchase from InnoTeletek or from a InnoTeletek authorized reseller. You dated sales or delivery receipt, showing the date of purchase of the product, is our proof of purchase date. During the warranty period, InnoTeletek will repair or replace the defective parts with new parts, or, at InnoTeletek’s discretion, used parts that meet or exceed performance specifications for new parts. All parts or products removed under this warranty become property of InnoTeletek. The replacement part or product takes on the warranty status of the removed part or product, In the unlikely event that your InnoTeletek product has a recurring failure, InnoTeletek, at its discretion, may elect to replace your product with comparable product. This is your exclusive remedy for defective products. EXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY, INNOTELETEK MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. INNOTELETEK EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS WORLDWIDE LIMITED WARRANTY STATEMENT. Before returning any unit for service, be sure to back up data and remove any confidential, proprietary, or personal information. InnoTeletek is not responsible for damage to or loss of any programs, data or removable storage media. Some states or countries do not allow limitation on how long an implied warranty lasts or the exclusion or limitation of the incidental or consequential damages for consumer products. In such states or countries, some exclusions or limitations of this Limited Warranty may not apply to you. This Limited Warranty gives you specific legal rights. You may also have other rights that may vary from This Limited Warranty does not apply to expendable parts. This Limited Warranty doest not extent to any product from which the serial number has been removed, damaged or rendered defective (a) as a result of accident, misuse, abuse, or other external causes;(b) by operation outside the usage parameters stated in the user Copyright © 2007 InnoTeletek, Inc. 59 Revised Version/ March 2007 User Manual state to state or from country to country. You are advised to consult applicable state or country laws for a full determination of your rights. Options and software The warranty terms and conditions for InnoTeletek options are as indicated in the Limited Warranty Statement applicable to InnoTeletek options. InnoTeletek’s only obligations with respect to software distributed by InnoTeletek under the InnoTeletek brand name are set forth in the applicable end-user license or program license agreement. Non-InnoTeletek hardware and software products are provided “AS-IS.” However, non-InnoTeletek manufacturers, suppliers, or publishers may provide their own warranties directly to you. Warranty Period The warranty period for this product is one (1) year from the date of product purchase. This warranty does not extent to expendable parts. Types of Warranty Service If your product needs service, call the InnoTeletek After-sales Service Dept. in your country or state at the number listed in the Contacting Customer Support in later section. A technical support specialist will help you diagnose the problem. Carry-in Warranty service Carry your product into InnoTeletek Authorized Center of warranty repair. To locate the service provider nearest you, access the service provider’s location on the InnoTeletek website; www.InnoTeletek.com or local reseller’s website you have purchased InnoTeletek product. Copyright © 2007 InnoTeletek, Inc. 60 Revised Version/ March 2007 User Manual Contacting InnoTeletek You are recommended to prepare the following information before you call InnoTeletek or a local service provider: Product Serial Number and Model Name Application error messages Add-on options Operating System version number Information on a third party hardware or software Detailed questions. If you have any requests for InnoTeletek service@innoteletek.com or call at +82-2-2059-8741 technical support, e-mail us at 9. Customer Care Information InnoTeletek, Inc. 461-25 Junmin-Dong, Yusung-Gu, Daejon, Republic of Korea 305-811 Tel: +82-(0)2-2059-8741 Fax: +82-(0)2-2059-8733 E-mail: service@innoteletek.com Information in this document is subject to change without notice Innoteletek, Inc. reserves the rights to make improvements in the product described in this manual at any time and without notice. This manual and the software described in this manual are copyrighted. All rights reserved. No part of this manual or the described software may be copied, reproduced, translated or reduced to any electronic medium or machine-readable form without the prior written consent of Innoteletek, Inc. Copyright © 2007 InnoTeletek, Inc. 61
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) Create Date : 2008:02:04 17:05:39+09:00 Modify Date : 2008:03:10 21:20:56+09:00 Metadata Date : 2008:03:10 21:20:56+09:00 Format : application/pdf Title : untitled Document ID : uuid:6f23090c-524e-4e4a-bc33-a4bcf3f069d7 Instance ID : uuid:aa130f98-3d46-4519-bea2-cc686a857a0d Page Count : 62EXIF Metadata provided by EXIF.tools