Honeywell VM3WLANA Vehicle Mount Computer User Manual VM3 W7 UG

Honeywell International Inc Vehicle Mount Computer VM3 W7 UG

UserManual.wiki >

Honeywell >

VM3WLANA User Manual >

User Manual_VM3-W7-UG Rev (a)-1

Thor™ VM3 Vehicle-Mount Computerwith Microsoft® Windows® Embedded Standard 7with Microsoft® Windows® 7 ProfessionalUser’s Guide

1Chapter 1 - Thor VM3 Agency InformationFCC Part 15 Statement........................................................................................................1-1FCC 5GHz Statement ..........................................................................................................1-1EMC Directive Requirements...............................................................................................1-1Canada, Industry Canada (IC) Notices................................................................................1-1ANATEL (Brazil)...................................................................................................................1-2Vehicle Power Supply Connection Safety Statement ..........................................................1-2Li-Ion Battery........................................................................................................................1-2RF Safety Notice..................................................................................................................1-2Bluetooth..............................................................................................................................1-2Honeywell Scanning & Mobility Product Environmental Information....................................1-2CE Mark ...............................................................................................................................1-2Chapter 2 - Getting StartedOverview ..............................................................................................................................2-1About this Guide ..................................................................................................................2-1Out of the Box ......................................................................................................................2-2Initial Setup for Thor VM3 ....................................................................................................2-2Hardware Setup .............................................................................................................2-2Software.........................................................................................................................2-2Languages ...............................................................................................................2-2First Boot..................................................................................................................2-2Software Setup.........................................................................................................2-2Quick Mount Smart Dock .....................................................................................................2-2Components.........................................................................................................................2-3Front View......................................................................................................................2-3Back View with Quick Mount Smart Dock......................................................................2-3 Access Panels...............................................................................................................2-4Backlights and Indicators .....................................................................................................2-5Display Backlight............................................................................................................2-5Power Management .................................................................................................2-5Backlight Brightness.................................................................................................2-5Screen Blanking .......................................................................................................2-5Keypad Backlight ...........................................................................................................2-5Speaker Volume.............................................................................................................2-5Power Up .............................................................................................................................2-6Rebooting the Thor VM3................................................................................................2-7Restart......................................................................................................................2-7Tapping the Touch Screen with a Stylus .............................................................................2-7Setup Terminal Emulation Parameters ................................................................................2-7Cleaning the Touch Screen .................................................................................................2-8Startup Help .........................................................................................................................2-8Chapter 3 - Hardware OverviewTable of Contents

2System Hardware................................................................................................................3-1802.11a/b/gWireless Client............................................................................................3-1Central Processing Unit.................................................................................................3-1Input/Output Components..............................................................................................3-1System Memory.............................................................................................................3-1Video Subsystem...........................................................................................................3-1Audio Interface...............................................................................................................3-1Card Slots......................................................................................................................3-1CompactFlash (CF) Slot ..........................................................................................3-1Secure Digital (SD) Slot...........................................................................................3-1Bluetooth EZPair............................................................................................................3-1WWAN...........................................................................................................................3-2GPS ...............................................................................................................................3-2Power ..................................................................................................................................3-2Vehicle DC Power Supply..............................................................................................3-2External AC Power Supply ............................................................................................3-2Uninterruptible Power Supply ........................................................................................3-2Safe Charging Temperature Range.........................................................................3-2Charging Timeout ....................................................................................................3-3Charging and Power Management..........................................................................3-3Backup Battery ..............................................................................................................3-3Fuse...............................................................................................................................3-4Power Management Modes...........................................................................................3-4Power Controls ..............................................................................................................3-4Power Switch...........................................................................................................3-4Power Button ...........................................................................................................3-4External Connectors............................................................................................................3-4Serial Connector (COM1 and COM2)............................................................................3-5 Screen Blanking......................................................................................................3-5USB Connector(s)..........................................................................................................3-5CANbus / Audio Connector............................................................................................3-6Power Supply Connector...............................................................................................3-6Antenna Connections ....................................................................................................3-6External Antenna Connector....................................................................................3-7Internal 802.11 Antenna ..........................................................................................3-7Vehicle Remote Antenna.........................................................................................3-7Keyboard Options................................................................................................................3-8Integrated Keypad .........................................................................................................3-8Keypad LEDs...........................................................................................................3-895-Key USB Keyboard...................................................................................................3-8Keyboard Backlight..................................................................................................3-8USB Keyboard / Mouse .................................................................................................3-9LED Functions.....................................................................................................................3-9System LEDs.................................................................................................................3-9SYS (System Status) LED....................................................................................... 3-9UPS Status LED ....................................................................................................3-10Charge Level....................................................................................................3-10Charging State.................................................................................................3-10

3SSD (Solid State Drive) LED .................................................................................3-10Connection LEDs.........................................................................................................3-11WWAN LED...........................................................................................................3-11Wi-Fi LED ..............................................................................................................3-11Bluetooth LED........................................................................................................3-11Keyboard LEDs............................................................................................................3-12Blue LED................................................................................................................3-12Orange LED...........................................................................................................3-12Programmable LED ...............................................................................................3-12Display...............................................................................................................................3-12Touch Screen ..............................................................................................................3-12Touch Screen Defroster...............................................................................................3-12Screen Blanking...........................................................................................................3-13Display Backlight Control.............................................................................................3-13Chapter 1 - Vehicle Mounting and Accessory InstallationIntroduction........................................................................................................................1-15Prepare for Vehicle Mounting............................................................................................1-15Quick Start...................................................................................................................1-15Maintenance - Vehicle Mounted Devices ..........................................................................1-15Cleaning ............................................................................................................................1-16Place Thor VM3 in the Dock..............................................................................................1-16Dock I/O Pin Cover......................................................................................................1-17Padlock........................................................................................................................1-17Laptop Security Cable .................................................................................................1-17Install RAM Mount .............................................................................................................1-18Components - RAM Mounting Kits ..............................................................................1-18Procedure - RAM Mount Assembly .............................................................................1-19Torque Measurement ............................................................................................1-19Step 1a – Attach RAM Ball to Vehicle ...................................................................1-19Mounting Dimensions ......................................................................................1-19Step 1b – Mount RAM Clamp to Vehicle ...............................................................1-20Mounting Dimensions ......................................................................................1-20Step 1c – Attach RAM Plate to Vehicle and Attach RAM Ball ...............................1-21Mounting Dimensions ......................................................................................1-21Step 2 – Attach RAM Mount Ball to the Thor VM3 Quick Mount Smart Dock .......1-22Step 3 – Attach Thor VM3 Assembly to RAM Mount.............................................1-22Step 4 – Place the Thor VM3 into the Dock...........................................................1-22Connect Cables.................................................................................................................1-23Strain Relief Cable Clamps..........................................................................................1-23Connect Power ............................................................................................................1-24Power Cable Cautions.................................................................................................1-2412-48 VDC Vehicles (10-60 VDC Direct Connection)............................................1-25Power Cable Identification.....................................................................................1-25 Vehicle 10-60VDC Direct Power Connection..................................................1-25Ignition Control Wiring Diagram.................................................................1-27Auto-On Control Wiring Diagram ...............................................................1-28Manual Control Wiring Diagram.................................................................1-29

460-144 VDC Vehicles (50-150 VDC Power Supply, Screws on Side of Lid) .........1-29Power Cable Identification.....................................................................................1-30Vehicle 50-150VDC Power Connection...........................................................1-30Wiring Diagram ..........................................................................................1-3260-144 VDC Vehicles (50-150 VDC Power Supply, Screws on Top of Lid) .......... 1-33Power Cable Identification.....................................................................................1-33Vehicle 50-150VDC Power Connection...........................................................1-34Wiring Diagram ..........................................................................................1-35VX6 / VX7 Adapter Cable ......................................................................................1-36Connect to VX6 / VX7 Power Cable ................................................................1-36Thor VX8 / Thor VX9 Adapter Cable .....................................................................1-37Connect to Thor VX8 / VX9 Power Cable........................................................1-37Screen Blanking.....................................................................................................1-38Screen Blanking Cable ....................................................................................1-38Honeywell Screen Blanking Box Cable......................................................1-38User-Supplied Cable..................................................................................1-39Screen Blanking Box........................................................................................1-39Screen Blanking with Switch............................................................................1-40External AC/DC Power Supply ..............................................................................1-41Connect External Power Supply ......................................................................1-41Connect USB Host.......................................................................................................1-42Connect USB Client.....................................................................................................1-42Connect Serial Device .................................................................................................1-42Connect a Tethered Scanner.................................................................................1-42Connect Headset Cable...............................................................................................1-43Adjust Headset / Microphone and Secure Cable...................................................1-43Under Clothing.................................................................................................1-44Over Clothing...................................................................................................1-44Connect CANbus Cable...............................................................................................1-44Install Remote Antenna ...............................................................................................1-45802.11 Remote Mount Antenna.............................................................................1-45Components and Mounting Diagram ...............................................................1-45Typical Installation ...........................................................................................1-46Mounting Instructions.......................................................................................1-46WAN Remote Mount Antenna ...............................................................................1-47GPS Remote Mount Antenna ................................................................................1-47Apply Touch Screen Protective Film .................................................................................1-48Installation....................................................................................................................1-48Chapter 2 - SoftwareMicrosoft Windows Setup and Configuration.......................................................................2-1Drive C Folder Structure................................................................................................2-1Software Loaded on Drive C....................................................................................2-1Microsoft Windows.............................................................................................2-1Device Drivers....................................................................................................2-1Radio Software ..................................................................................................2-1Touch Screen Software .....................................................................................2-1RFTerm..............................................................................................................2-1

5Summit Client Utility...........................................................................................2-1Freefloat Link*One Wedge.................................................................................2-2Freefloat Access*One TE (Optional)..................................................................2-2Control Panel.......................................................................................................................2-3About .............................................................................................................................2-3Software...................................................................................................................2-3Firmware Versions.............................................................................................2-3Language...........................................................................................................2-3Versions...................................................................................................................2-3Versions Tab and the Registry...........................................................................2-3Network IP ...............................................................................................................2-3MAC Address.....................................................................................................2-4Bluetooth........................................................................................................................2-5Bluetooth Devices....................................................................................................2-6Discover...................................................................................................................2-6Stop Button ........................................................................................................2-6Bluetooth Device List .........................................................................................2-7Clear Button.......................................................................................................2-7Bluetooth Device Menu......................................................................................2-7Right-Click Menu Options ............................................................................2-7Bluetooth Device Properties ..............................................................................2-8Settings....................................................................................................................2-8Turn Off Bluetooth..............................................................................................2-8Options...............................................................................................................2-8Reconnect..............................................................................................................2-10Options.............................................................................................................2-10About .....................................................................................................................2-11Using Bluetooth .....................................................................................................2-12Bluetooth Devices Display - Before Discovering Devices................................2-12Initial Configuration ..........................................................................................2-12Subsequent Use ..............................................................................................2-12Bluetooth Indicators .........................................................................................2-13Bluetooth Bar Code Reader Setup ..................................................................2-13Thor VM3 with Label..................................................................................2-14Thor VM3 without Label.............................................................................2-14Bluetooth Beep and LED Indications .........................................................2-15Bluetooth Printer Setup..............................................................................2-15Easy Pairing and Auto-Reconnect...................................................................2-15Display.........................................................................................................................2-16Power Options .............................................................................................................2-17Select a Power Scheme ........................................................................................2-17Power Schemes...............................................................................................2-17View UPS Battery Status.......................................................................................2-18Power Meter.....................................................................................................2-18Configure Power Button Behavior....................................................................2-18Advanced...................................................................................................2-18Hibernate ...............................................................................................................2-19

6Enable Hibernation ..........................................................................................2-19Screen Control.............................................................................................................2-20Screen Blanking.....................................................................................................2-21Screen Rotation...........................................................................................................2-22Sounds......................................................................................................................... 2-22User Accounts .............................................................................................................2-22Wi-Fi ............................................................................................................................2-23Bar Code Readers.............................................................................................................2-24Scanner Wedge...........................................................................................................2-24Touch Screen Calibration..................................................................................................2-24BIOS.................................................................................................................................. 2-25Accessing the BIOS Setup ..........................................................................................2-25Boot Order ...................................................................................................................2-25Exiting BIOS Setup......................................................................................................2-25Thor VM3 Recovery DVD..................................................................................................2-25Windows Embedded Standard 7 and Windows 7 Professional:............................2-26Using Configuration Cloning Utility GUI.......................................................................2-26Chapter 3 - Wireless Network ConnectionsNetwork Connections Control Panel....................................................................................3-1Summit Wireless Network Configuration.............................................................................3-1Important Notes...................................................................................................................3-1Summit Client Utility ............................................................................................................3-1Summit Tray Icon...........................................................................................................3-1Wireless Zero Config Utility ...........................................................................................3-2To Switch Control to the Wireless Zero Config Utility..............................................3-2To Switch Control to SCU........................................................................................3-2Main...............................................................................................................................3-3Admin Login.............................................................................................................3-3Profile.............................................................................................................................3-5Buttons.....................................................................................................................3-5Profile Parameters...................................................................................................3-6Status.............................................................................................................................3-8Diags..............................................................................................................................3-9Global ..........................................................................................................................3-10Custom Parameter Option.....................................................................................3-11Global Parameters.................................................................................................3-11Logon Options .......................................................................................................3-13Single Signon...................................................................................................3-14Pre-Logon Connection.....................................................................................3-14Sign-On vs. Stored Credentials.........................................................................................3-15To Use Stored Credentials ..........................................................................................3-15To Use Sign On Screen...............................................................................................3-16To Use Windows Username and Password ................................................................3-16Windows Certificate Store vs. Certs Path..........................................................................3-17User Certificates ..........................................................................................................3-17Root CA Certificates ....................................................................................................3-17Certs Path..............................................................................................................3-17

8Folder...............................................................................................................3-51Settings............................................................................................................3-52New SMS.........................................................................................................3-52Reply................................................................................................................3-52Forward............................................................................................................3-52Move SMS.. .....................................................................................................3-52Delete...............................................................................................................3-52Send/Receive...................................................................................................3-52Addresses........................................................................................................3-53Web Browser .........................................................................................................3-53Email......................................................................................................................3-53GPS .......................................................................................................................3-53About ...........................................................................................................................3-54System Requirements ...........................................................................................3-54Supported Languages......................................................................................3-54Installing or Upgrading OneClick Internet ........................................................3-54Installation........................................................................................................3-54OneClick Internet Connection Manager.......................................................................3-56Connection Management.......................................................................................3-57Information Buttons................................................................................................3-58Chapter 4 - Key MapsIntegrated Keypad ...............................................................................................................4-1External 21-Key Keyboard...................................................................................................4-2External 95-Key Keyboard...................................................................................................4-2Chapter 5 - Specifications and Reference MaterialTechnical Specifications......................................................................................................5-1Thor VM3.......................................................................................................................5-1Smart Dock....................................................................................................................5-2Enhanced Smart Dock...................................................................................................5-2Dimensions..........................................................................................................................5-3Thor VM3.......................................................................................................................5-3Smart Dock....................................................................................................................5-3Environmental Specifications ..............................................................................................5-4Thor VM1 and Smart Dock ............................................................................................5-4Network Card Specifications ...............................................................................................5-4?? 802.11a/b/g/n............................................................................................................5-4Bluetooth........................................................................................................................5-4WWAN...........................................................................................................................5-4Port and Connector Pinouts ................................................................................................5-5Power Supply Connector...............................................................................................5-5COM1 and COM2 Connector ........................................................................................5-5USB Connector..............................................................................................................5-6USB Y Cable............................................................................................................5-6D9 Male Connector............................................................................................5-6USB Host Connector..........................................................................................5-6

9USB Client Connector........................................................................................5-6USB Connector2............................................................................................................5-7USB Y Cable............................................................................................................5-8D15 Male Connector..........................................................................................5-8USB Host Connector..........................................................................................5-8USB Host Connector..........................................................................................5-8CANbus / Audio Connector............................................................................................5-9Headset Adapter Cable ...........................................................................................5-9D15 Female Connector......................................................................................5-9Quick Connect Headset Connector ...................................................................5-9CANbus Y Cable....................................................................................................5-10D15 Female Connector....................................................................................5-109-Pin J1939 (Deutsch) Connectors..................................................................5-10Hat Encoding..................................................................................................................... 5-11Chapter 6 - Customer SupportProduct Service and Repair.................................................................................................6-1Technical Assistance...........................................................................................................6-1Limited Warranty .................................................................................................................6-1

1 - 11Thor VM3 Agency InformationThor VM3 mobile computers meet or exceed the requirements of all applicable standards organizations for safe operation. However as with any electrical equipment, the best way to ensure safe operation is to operate them according to the agency guidelines that follow. Read these guidelines before using your Thor VM3.This documentation is relevant for the following Thor models: VM3.FCC Part 15 StatementThis device complies with FCC Rules, part 15 [and with RSS-210 of Industry Canada]. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. NOTE - This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Opera-tion of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to cor-rect the interference at his own expense.Caution - Changes or modifications made to this equipment not expressly approved by Honeywell may void the FCC authoriza-tion to operate this equipment.FCC 5GHz StatementFor the band 5600-5650 MHz, no operation is permitted.EMC Directive RequirementsThis is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.Canada, Industry Canada (IC) NoticesThis Class A digital apparatus complies with Canadian RSS-GEN issue 3:2010 and RSS-210 issue 8:2010.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Radio Frequency (RF) Exposure InformationThe radiated output power of the Honeywell Thor VM3 is below the Industry Canada (IC) radio frequency exposure limits. The Honeywell Thor VM3 should be used in such a manner such that the potential for human contact during normal operation is minimized.This device has been certified for use in Canada. Status of the listing in the Industry Canada’s REL (Radio Equipment List) can be found at the following web address: Additional Canadian information on RF exposure also can be found at the following web address: Canada, avis d'Industry Canada (IC)Cet appareil numérique de classe A est conforme aux normes canadiennes RSS-GEN numéro 3:2010 et RSS-210 numéro 8:2010.Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement.Informations concernant l'exposition aux fréquences radio (RF)High-power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65- to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device.!

1 - 2La puissance de sortie émise par de le Honeywell Thor VM3 est inférieure à la limite d'exposition aux fréquences radio d'Indus-try Canada (IC). Utilisez le Honeywell Thor VM3 de façon à minimiser les contacts humains lors du fonctionnement normal.Ce périphérique est homologué pour l'utilisation au Canada. Pour consulter l'entrée correspondant à l’appareil dans la liste d'équipement radio (REL - Radio Equipment List) d'Industry Canada rendez-vous sur: Pour des informations supplémentaires concernant l'exposition aux RF au Canada rendez-vous sur : ANATEL (Brazil)Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não causar interferência a sistema operando em caráter primário.ANATEL (Brazil)Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não causar interferência a sistema operando em caráter primário.Vehicle Power Supply Connection Safety StatementNote: For North America, a UL Listed fuse is to be usedFor proper and safe installation, the input power cable must be connected to a fused circuit on the vehicle. If the supply connec-tion is made directly to the battery, the fuse should be installed in the positive lead within 5 inches (12.7 cm) of the battery’s pos-itive (+) terminal. Use VM3055FUSEKIT to install this fuse or use equivalent 20A fast blow fuse.Li-Ion BatteryWhen disposing of the Thor VM3 UPS battery, the following precautions should be observed: The battery should be disposed of properly. The battery should not be disassembled or crushed. The battery should not be heated above 212°F (100°C) or inciner-ated.Safety requirements restrict the temperature at which the Li-Ion UPS battery can be charged. Charging is disabled if the ambi-ent temperature is outside of the 0ºC to 35ºC safe charging range. In order to maintain UPS charge the Thor VM3 should have power applied while the unit is within the safe charging range for at least an hour each day.RF Safety NoticeBluetoothHoneywell Scanning & Mobility Product Environmental InformationRefer to www.honeywellaidc.com/environmental for the RoHS / REACH / WEEE information.CE MarkThe CE marking on the product indicates that this device is in conformity with the following directives:• 1995/5/EC R&TTE• 2011/65/EU RoHS (Recast)In addition, complies to 2006/95/EC Low Voltage Directive, when shipped with recommended power supply. European contact:Hand Held Products Europe BVNijverheidsweg 9-135627 BT EindhovenThis device is intended to transmit RF energy. For protection against RF exposure to humans and in accordance with FCC rules and Industry Canada rules, this transmitter should be installed such that a minimum separation distance of at least 20 cm (7.8 in.) is maintained between the antenna and the general population. .Class II

1 - 3The NetherlandsHoneywell shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive. WWAN is not available in Singapore.

2 - 12Getting StartedOverviewThe Thor VM3 Vehicle Mount Computer (VMC) is a rugged, vehicle mounted computer running a Microsoft® Windows® Embed-ded Standard 7 (32-bit) or Windows® 7 Professional (64-bit) or Windows® operating system and capable of wireless data com-munications from a fork-lift truck or any properly configured vehicle. Wireless communications are supported over a 802.11 WLAN network and, optionally, over a WWAN network. The Bluetooth® module supports Bluetooth printers and scanners.The Thor VM3 is designed for use with a vehicle Quick Mount Smart Dock. The dock installs in the vehicle and connects to vehicle power. The dock provides conditioned input power for the Thor VM3. Peripheral connections are on the dock. The Thor VM3 is designed to easily be removed from the dock with a latch on the lower rear of the Thor VM3 housing. Since the dock remains attached to the vehicle, the Thor VM3 computer can easily be moved from one vehicle equipped with a dock to another vehicle equipped with a dock.The Thor VM3 contains a UPS battery which, when fully charged, can power the Thor VM3 for a minimum of 30 minutes. This can be when the Thor VM3 is not attached to a Quick Mount Smart Dock or when the Thor VM3 is attached to a dock but the vehicle power is interrupted, such as when the vehicle battery is being changed.The Thor VM3 can be used with or without an external keyboard. There are 7 programmable keys (P1-P7) on the front bezel and, when used with the Orange modifier key, provide 7 additional programmable keys (P8-P14).Contact Technical Assistance (page 6-1) for information on the latest upgrades for your Thor VM3.About this GuideThis user’s guide has been developed for a Thor VM3 with a Microsoft® Windows® 7 Professional or Windows® Embedded Standard 7 operating system.CAUTION - Before shipping the Thor VM3, be sure to Disconnect UPS Battery (page 1-54) .!P8P1 P14P7P13P6P12P5P11P4P10P3P9P2

2 - 2Out of the BoxThe following items may be packaged separately:•Thor VM3• Quick Mount Smart Dock (includes 10-60VDC power cable)• RAM or U-Bracket vehicle mount kitIf you ordered additional accessories for the Thor VM3, verify they are also included with the order. Keep the original packaging material in the event the Thor VM3 should need to be returned for service. For details, see Product Service and Repair (page 6-1).Initial Setup for Thor VM3This page lists a quick outline of the steps you might take when setting up a new Thor VM3. More instruction for each step is listed later in this guide.Contact Technical Assistance (page 6-1) if you need additional help.Hardware Setup1. Install RAM Mount (page 1-18) or Install U Bracket Mount (page 1-23) to the vehicle.2. Place Thor VM3 in the Dock (page 1-16).3. Connect Cables (page 1-23) for any peripherals.4. Connect Power (page 1-24).5. Secure all cables in Strain Relief Cable Clamps (page 1-23).6. Press the Power Switch (page 3-4) on the dock to the on position.7. Press the Power Button (page 3-4) on the Thor VM3.SoftwareLanguagesFirst BootWhen a new Thor VM3 starts up a EULA (End User License Agreement) may be displayed on the touch screen. It remains on the screen until the Accept or Decline button is tapped with a stylus.Tap the Accept button to accept the EULA terms and the Thor VM3 continues the startup process. The EULA is not presented to the user again.Tap the Decline button to decline the EULA and the Thor VM3 reboots. It will continue to reboot until the Accept but-ton is tapped with the stylus.Software SetupHardware setup should be completed before starting software setup.Quick Mount Smart DockThe Thor VM3 assembly consists of two parts, the Thor VM3 computer and the Quick Mount Smart Dock.The Thor VM3 contains an internal UPS battery that, once fully charged, powers the Thor VM3 for a minimum of 30 minutes when the unit is not mounted in the dock.The dock provides:• A mount for the Thor VM3 computer. The dock attaches to a vehicle via a RAM or U-bracket mount or to a RAM table stand for use in an office environment.• Conditioned power for the Thor VM3. The dock accepts 10-60VDC power input directly or 50-150VDC power input with a DC/DC converter.• COM1 and COM2 serial connections for a tethered scanner, printer, PC connection, etc.• USB host connection via an adapter cable.

2 - 3• CANbus connection via an adapter cable.• Headset connection via an adapter cable. When a headset is not attached, the microphone and speakers on the Thor VM3 are active.• Strain relief cable mounts.• Mobility of the Thor VM3, since the dock remains attached to the vehicle the Thor VM3 computer can easily be moved from one vehicle equipped with a dock to another.External antenna connectors may be present on the back of the Thor VM3. The connectors may include:• 802.11 antenna connectors, used when the Thor VM3 is not equipped with internal antennas.• External GPS antenna connector, when the Thor VM3 is equipped with GPS.• External WWAN antenna connectors, when the Thor VM3 is equipped with WWAN. Optional WWAN radio (available in North America, Europe, New Zealand, and Australia only).ComponentsFront ViewBack View with Quick Mount Smart DockP8P1 P14P7P13P6P12P5P11P4P10P3P9P2SpeakersMicrophonePowerButtonAmbientLightSensor

2 - 5Backlights and IndicatorsDisplay BacklightThere are several configuration options for the Thor VM3 display backlight:Power ManagementThe display backlight is controlled by power management. When the user activity timer expires, the display backlight is turned off. Timeouts can be set for the available power management schemes.See Power Options (page 2-17) for configuration options.Backlight BrightnessThe intensity of the display backlight can be manually configured:1. Press the Blue key to enter Blue mode2.3. Press the P5 key to increase backlight brightness or the P6 key to decrease backlight brightness.4. Press the Blue key to exit Blue mode.Refer to the Screen Control (page 2-20) panel for the current display brightness level.Screen BlankingThe Thor VM3 can be configured to blank (blackout) the display while the vehicle is in motion.Refer to the Screen Control (page 2-20) panel for information.Keypad BacklightBy default, the integrated keypad backlight follows the display backlight. The integrated keypad backlight can be disabled.To change this behavior, see the Options (see page 5-23) control panel.The external USB keyboard backlight is manually controlled.Speaker VolumeThe speaker volume can be adjusted via the Thor VM3 keypad:1. Press the Blue key to enter Blue mode2. Press the P1 key to increase speaker volume or the P2 key to decrease speaker volume.3. Press the Blue key to exit Blue mode.The current volume level can be viewed on the Sounds (page 2-22) control panel or via the system tray speaker icon. These items can also be used to adjust speaker volume

2 - 6Power UpThe Quick Mount Smart Dock has a power switch on the back.The “On” side of this rocker switch has a raised bump to allow the state of the switch to be determined when the switch may not be easily viewed, for example, after the dock is mounted in a vehicle.After external power has been connected and the Thor VM3 has been mounted in the dock, press the side of the power switch with the raised bump to pass power from the dock to the Thor VM3. Next locate the power button on the front of the Thor VM3.Press the power button to turn the Thor VM3 on. When the Windows desktop is displayed or an application begins, the power up sequence is complete.See Power Controls (see page 3-4) for more information.If a USB drive, such as a thumb drive is attached to the Thor VM3, the device attempts to boot from the USB drive and cannot. Please remove the USB drive and power up the Thor VM3 again.!

2 - 7Rebooting the Thor VM3•RestartRestart performs a controlled shutdown of the Thor VM3 and then restarts the device.• Use the Ctrl + Alt + Del keypress sequence to start the task manager. Tap the Shut Down button and select Restart from the pull-down list. Tap the OK button to restart the Thor VM3.•Select Start > Shut Down > Restart and tap OK to restart the Thor VM3Tapping the Touch Screen with a StylusNote: Always use the point of the stylus for tapping or making strokes on the touch screen. Never use an actual pen, pencil, or sharp/abrasive object to write on the touch screen.Hold the stylus as if it were a pen or pencil. Touch an element on the screen with the tip of the stylus then remove the stylus from the screen.Firmly press the stylus into the stylus holder when the stylus is not in use.Using a stylus is similar to moving the mouse pointer then left-clicking icons on a desktop computer screen.Using the stylus to tap icons on the touch screen is the basic action that can:• Open applications• Choose menu commands• Select options in dialog boxes or drop-down boxes• Drag the slider in a scroll bar• Select text by dragging the stylus across the text• Place the cursor in a text box prior to typing in data• Place the cursor in a text box prior to retrieving data using a scanner/imager.Note: If the mouse icon is not displayed, this feature can be enabled by tapping the PenMount icon in the System Tray. From the menu that pops up, tap the Right Button to enable the mouse icon. When this option is enabled, a checkmark is displayed in the menu.A stylus replacement kit is available. When a dialog box is too large for the display, tap and drag the dialog box up or down or from side to side to view the remainder of the dialog box.Setup Terminal Emulation ParametersNote: The instructions below are for Honeywell RFTerm. If a different terminal emulation software is installed on your Thor VM3 refer to the documentation for that software.Before you make a host connection, you will, at a minimum, need to know:• the alias name or IP address (Host Address) and • the port number (Telnet Port) of the host system to properly set up your host session. 1. Make sure the mobile client network settings are configured and functional. If you are connecting over wireless LAN (802.11x), make sure your mobile client is communicating with the Access Point.2. From Start > Program, run RFTerm or tap the RFTerm icon on the desktop.3. Select Session > Configure from the application menu and select the “host type” that you require. This will depend on the type of host system that you are going to connect to; i.e., 3270 mainframe, AS/400 5250 server or VT host. If a USB drive, such as a thumb drive is attached to the Thor VM3, the device attempts to boot from the USB drive:• If the USB drive contains a bootable sector, the Thor VM3 boots from the USB drive.• If the USB drive does not contain a bootable sector, the Thor VM3 does not boot. Remove the USB drive and boot the Thor VM3 again.A right click is generated by tapping the mouse icon , usually located in the upper right hand corner of the screen. After tapping, the mouse icon highlights the right button. The next touch screen tap is treated as a right click. The mouse icon returns to the left button highlighted so subsequent taps are treated as left clicks.!

2 - 84. Enter the “Host Address” of the host system that you wish to connect to. This may either be a DNS name or an IP address of the host system.5. Update the telnet port number, if your host application is configured to listen on a specific port. If not, just use the default telnet port.6. Select OK.7. Select Session > Connect from the application menu or tap the “Connect” button on the Tool Bar. Upon a successful connection, you should see the host application screen displayed.To change options such as Display, Colors, Cursor, Bar Code, etc., refer to these sections in the RFTerm Reference Guide for complete descriptions of these and other features.Cleaning the Touch ScreenNote: These instructions are for components made of glass. If there is a removable protective film sheet on the display, remove the film sheet before cleaning the screen.Keep fingers and rough or sharp objects away from the bar code reader scanning aperture and the mobile device touch screen. If the glass becomes soiled or smudged, clean only with a standard household cleaner such as Windex® without vinegar or use isopropyl alcohol. Dampen the cloth with the cleaner and then wipe the surface. Do not use paper towels or harsh-chemical-based cleaning fluids since they may result in damage to the glass surface. Use a clean, damp, lint-free cloth.Do not scrub optical surfaces. If possible, clean only those areas which are soiled. Lint and particulates can be removed with clean, filtered canned air. Startup HelpContact Technical Assistance (page 6-1) if you need more help.Thor VM3 seems to lockup as soon as it is rebooted. There may be slight delays while the wireless client connects to the network, authoriza-tion for voice-enabled applications complete, and Bluetooth relationships establish or re-establish. When an application begins, the Thor VM3 is ready for use.

3 - 13Hardware OverviewSystem Hardware802.11a/b/gWireless ClientCentral Processing Unit The CPU is a 1.6 GHz Intel Atom processor. The operating system is Microsoft Windows . The OS image is stored on an internal CompactFlash memory card and is loaded into DRAM for execution. Input/Output ComponentsThe Thor VM3 supports the following I/O components of the core logic:• Two 9-pin RS-232 serial ports, COM1 and COM2.• One slot for SD memory card.• CompactFlash (CF) memory card drive.• Integrated keyboard.• Ports available via adapter cables: USB host port, CANbus, Audio. System MemoryMain system memory is GB SDRAM.Video SubsystemThe Thor VM3 video subsystem consists of a color TFT display. The video subsystem complies with the VESA VL bus standard. The resolution of this display is 800 x 480 pixels. This resolution complies with the WVGA graphics industry standard.The display supports screen blanking to eliminate driver distraction when the vehicle is in motion.Audio InterfaceSpeakers are located on the bottom front of the Thor VM3. A headset adapter cable provides a connection for headset operation. When a headset is plugged into the adapter cable, the main speakers are disabled.A microphone is located at the upper right of the Thor VM3 display, near the Thor VM3 emblem. When a headset is plugged into the adapter cable, the internal microphone is disabled.Card SlotsCompactFlash (CF) SlotThe CF ATA slot is not hot swappable. The Thor VM3 must be powered down to insert or remove an ATA card. Since the operating system is stored on the CF ATA card, the Thor VM3 cannot operate without the ATA card.Secure Digital (SD) SlotThe SD slot accepts an SD memory card. The SD card is hot swappable.Bluetooth EZPairThe Thor VM3 contains Bluetooth version 2.0 with Enhanced Data Rate (EDR) up to 3.0 Mbit/s over the air. Bluetooth device connection (or pairing) can occur at distances up to 32.8 ft (10 meters) Line of Sight. The wireless client retains wireless connectivity while Bluetooth is active.The user cannot select PIN authentication or encryption on connections from the Thor VM3. However, the Thor VM3 sup-ports authentication requests from pairing devices. If a pairing device requests authentication or encryption, the Thor VM3 displays a prompt for the PIN or passcode. Maximum encryption is 128 bit. Encryption is based on the length of the user’s passcode.

3 - 2Bluetooth simultaneously supports one printer as a slave Bluetooth device and one scanner, either as a slave or as a mas-ter Bluetooth device.• The LED on the Bluetooth scanner illuminates during a scanning operation.• Multiple beeps may be heard during a bar code scan using a mobile Bluetooth scanner; beeps from the mobile Bluetooth scanner as the bar code data is accepted/rejected, and other beeps from the Thor VM3 during final bar code data manipulation.WWANWWAN (Wireless Wide Area Networking) is available on the Thor VM3. A slot is provided for a SIM card.GPSGPS (Global Positioning System) is available on the Thor VM3.PowerVehicle DC Power SupplyVehicle power input for the Thor VM3 dock is 10V to 60V DC and is accepted without the need to perform any manual oper-ation within the Thor VM3 dock, see 12-48 VDC Vehicles (10-60 VDC Direct Connection) (page 1-25). The dock provides a conditioned power output for the Thor VM3. By using a specified DC/DC power supply, input voltage of 50-150V DC can be accepted, see 60-144 VDC Vehicles (50-150 VDC Power Supply, Screws on Top of Lid) (page 1-33) or 60-144 VDC Vehicles (50-150 VDC Power Supply, Screws on Top of Lid) (page 1-33).Power input is fused for protection and the fuse is externally accessible, see Fuse (page 3-4).External AC Power SupplyIf DC power is not available – for example, in an office environment – an optional external Universal Input Power Supply can be used to convert AC wall power to an appropriate DC level. AC to DC power input for the Thor VM3 is delivered to the Quick Mount Smart Dock via an optional external power supply and adapter cable. See External AC/DC Power Supply (page 1-41).Uninterruptible Power SupplyThe Thor VM3 contains an internal UPS battery. The user can Replace UPS Battery (page 1-83) The UPS battery is automatically charged when the Thor VM3 is placed in a powered dock, provided the safe charging tem-perature conditions below are met.When external power is removed, the UPS automatically powers the Thor VM3 with no user intervention. When running on UPS power, the power management timeouts may be different than when vehicle power is applied.The UPS allows the Thor VM3 to continue operation when not mounted in a dock or when the vehicle battery is being swapped. When fully charged the UPS battery is designed to power the Thor VM3 for a minimum of 30 minutes at tem-peratures of -20ºC (-4ºF) or greater. For the extended temperature version of the Thor VM3, the UPS provides a minimum of 10 minutes of operation between -20ºC (-4ºF) and -30ºC (-22ºF).If operating on UPS power and the UPS battery becomes critically low, the Thor VM3 performs a controlled shutdown.If there is no external power available, there must be 10% or greater power in the UPS battery or the Thor VM3 does not power on.The UPS status LED and the Battery Control Panel can be used to monitor the state of the UPS battery.Safe Charging Temperature RangeThe internal temperature of the Thor VM3 is the trigger for UPS battery charging.• The UPS battery is not charged when the internal Thor VM3 temperature is below 0°C (32°F). This corresponds to an ambient (room) temperature of approximately -10°C (-14°F).• The UPS battery is not charged when the internal Thor VM3 temperature is above 45°C (113°F). This corresponds to an ambient (room) temperature of approximately 35°C (95°F).

3 - 3• If the UPS battery cannot be charged due to a temperature extreme, the UPS Status LED (page 3-10) is amber. Move the Thor VM3 to a different location to charge the UPS battery.When the Thor VM3 is operated in an environment where the UPS battery is not able to charge due to temperature extremes, the Thor VM3 should be removed to a location within the safe charging temperature range during off hours. A discharged UPS battery cannot protect against data loss in the event vehicle power is interrupted.Charging Timeout• A fully discharged UPS battery normally recharges in less than 4 hours when the Thor VM3 is in a powered dock and within the safe charging temperature range.• If the UPS battery is not charged before an 8 hour (or 4 hours for some earlier software revisions) timeout period expires, the UPS Status LED (page 3-10) is amber.• The charge timeout is reset if charging resumes upon application of external power.• The charge timeout is reset if charging resumes when the Thor VM3 enters the permissible temperature range for charging.Charging and Power ManagementBackup BatteryThe Thor VM3 has a permanent Lithium battery installed to maintain time, date and CMOS setup information for a minimum of 90 days. The lithium battery is not user serviceable and should last years with normal use before it requires replace-ment.Note: The backup battery should only be changed by authorized service personnel.

3 - 4FusePower Management ModesPower ControlsPower SwitchPower ButtonExternal ConnectorsPower the Thor VM3 off before attaching a cable to any port (serial, USB, Audio/CAN, etc.).The external I/O connectors for the Thor VM3 are located on the right side of the Quick Mount Smart Dock (when viewed from the back).The Power Supply Connector (page 3-6) is on the left side of the dock (when viewed from the back).Antenna connectors are located on the top rear of the Thor VM3.The Thor VM3 uses an 8A time delay (slow blow), fuse that is externally accessible and user replaceable. The fuse is located on the back of the Quick Mount Smart Dock. The fuse is accessed by unscrewing the cap as indicated.Should it need replacement, replace with same size, rating and type of fuse: • Littelfuse 0215008.MXP• Cooper Bussmann BK1/S506-8-R• Bel Fuse 5HT 8-Ror equivalent.Fuse has voltage on it even when power is off. Always disconnect input power before changing the fuse.After all cables are connected, the Thor VM3 can be powered on.There is a power switch located on the back of the Quick Mount Smart Dock. The power switch is a rocker switch.The power switch has a raised bump to identify the switch position even when it is hidden from view. When the side of the switch with the raised bump is pressed, the power switch is On. If the dock is connected to external power, the dock delivers power to the Thor VM3.Generally, once the dock is powered On, there is no need to power it off. The dock power can remain On even when the Thor VM3 is not attached.

3 - 5Serial Connector (COM1 and COM2) Screen BlankingThe screen blanking signal can be provided either by a Honeywell Screen Blanking Box or a user supplied switch or relay. See Screen Blanking (page 1-38) for information on connecting screen blanking accessories.USB Connector(s)The COM1 and COM2 connectors are D-9 male connectors located on the back of the Quick Mount Smart Dock.Power the Thor VM3 off before attaching a cable to any port (serial, USB, Audio/CAN, etc.).The serial connectors are industry-standard RS-232, PC/AT standard 9–pin “D” male connector. See COM1 and COM2 Connector (page 5-5) for connector pinout detail.See Connect Serial Device (page 1-42) for more information.If a COM port is not being used for a scanner, it can be used for Screen Blanking (page 1-38) when the vehicle is in motion. Smart Dock Enhanced Smart DocThe USB or USB1 connector is a D-9 female connector located on the back of the Quick Mount Smart Dock. See USB Connector (page 5-6) for connector pinout detail.The USB-2 connector is a D-15 female connector located on the back of the Quick Mount Smart Dock. See USB Connector (page 5-6) for connector pinout detail.Power the Thor VM3 off before attaching a cable to any port (serial, USB, Audio/CAN, etc.).Smart Dock Enhanced Smart DocCOM1COM2USBCANBUS/AUDIOCOM1COM2USBCANBUS/AUDIO

3 - 6CANbus / Audio ConnectorPower Supply ConnectorAntenna ConnectionsThe CANbus/Audio connector is a D-15 male connector located on the back of the Quick Mount Smart Dock.The connector supports a headset adapter cable or a CAN-bus cable. The Thor VM3 does not support connecting audio and CANbus simultaneously.See CANbus / Audio Connector (page 5-9) for connector pin-out detail.A headset cable attaches to the CANbus / Audio connector and provides a quick connect connection for a headset. See Connect Headset Cable (page 1-43) for more information.The CANbus Y cable has a 9 pin F SAE J1939 (Deutsch) and 9 pin M SAE J1939 (Deutsch) connector. See Connect CANbus Cable (page 1-44) for more information.The CANbus interface is a virtual COM4 port. This port can be accessed using standard Windows API calls.Smart Dock Enhanced Smart DocPower is supplied to the Thor VM3 through the power connector. Additionally this assembly pro-vides a connection point for the vehicle’s chassis ground to be connected internally to the conduc-tive chassis of the computer. The Thor VM3 internal power supply can accept DC input voltages in the range of 10 to 60 Volts DC.See Power Supply Connector (page 5-5) for connector pinout detail. See Connect Power (page 1-24) for more information on connecting power to the Thor VM3.The Thor VM3 is equipped with an 802.11 radio and can be ordered with internal an-tennas, external antennas or external remote mount antennas. When the Thor VM3 is ordered with internal antennas, the external antenna connectors are not used. GPS and WWAN are optional on the Thor VM3 and require external remote mount antennas.1. WI-FI (MAIN) 802.11 Main External Antenna Connector2. WAN (MAIN) (Blue label) Main WWAN Antenna Connector3. GPS (Green label) GPS Antenna Connector4. WAN (AUX) (Blue label) Auxiliary WWAN Antenna Connector5. WI-FI (AUX) 802.11 Auxiliary External Antenna ConnectorCOM1COM2USBCANBUS/AUDIO1 2 3 4 5

3 - 7External Antenna ConnectorInternal 802.11 AntennaIf the internal 802.11 antenna option is ordered, antennas are mounted inside the Thor VM3. The internal antennas are not user accessible.Vehicle Remote AntennaThe external antennas can be remotely mounted on the vehicle. See Install Remote Antenna (page 1-45) for instruc-tions. External antenna kits are available for the 802.11 Wi-Fi radio, GPS and WWAN.When the Thor VM3 is ordered with the internal antenna option, the 802.11 antenna connectors on the back are not connected to the 802.11 radio. Instead the internal antenna connector is connected to the 802.11 radio.Remove the rubber cap, if present, from the antenna connector before connecting an external antenna.

$3 - 8Keyboard Options••Integrated KeypadThe integrated keypad contains seven programmable keys, a blue modifier key and an orange modifier key.The P1 though P7 keys are user programmable.• When used with no modifier key, P1 through P7 can be configured for a user programmable function.• When used with the Orange modifier key, P1 through P7 provide secondary programmable keys, P8 through P14, and can be configured for a user programmable function.• The programmable keys can be remapped to provide a single keypress, a string of keypresses or to execute an application or command. Key remapping is configured via the Programmable Key (page 5-41) option in the Control Panel.• Programmable keys persist across a warmboot or power cycle.• When used with the Blue modifier key, P1 and P2 keys are used to adjust speaker volume and P5 and P6 keys are used to adjust display brightness.The Thor VM3 integrated keypad is backlit.• By default, the integrated keypad backlight follows the display backlight. When the display backlight is on, the integrated keypad backlight is on.• If the display backlight brightness is increased (or decreased) the integrated keypad backlight brightness is increased (or decreased).The integrated keypad backlight and the display share the same timer, which is configured in the Power Options (page 2-17) control panel.• The integrated keypad backlight can be disabled via the Options (page 5-23) control panel.Keypad LEDsSee Keyboard LEDs (page 3-12) for details.95-Key USB KeyboardThe Thor VM3 uses an optional rugged QWERTY 95 key keyboard, designed for ease of use with the Windows CE operat-ing system. The USB keyboard connects directly to the D9 USB connector on the Thor VM3 Quick Mount Smart Dock.• The 95 key keyboard supports all 104 keyboard functions (101 standard keyboard plus Windows keys) and includes an integrated pointing device and left and right mouse buttons. However, because the keyboard only has 95 keys, all functions are not visible (or printed on the keyboard). Therefore the keyboard supports what is called hidden keys - keys that are accessible but not visible on the keyboard.• The 95 key keyboard keys are backlit. The keyboard backlight is manually controlled.Keyboard BacklightThe keyboard backlight key in the top right hand corner has a light bulb icon.P8P1 P14P7P13P6P12P5P11P4P10P3P9P2PrintScreenSysRqScrollLockPauseBreak67 BackSpace NumLockERTYUI OP]\[{}|7410HomeDF GHJ K L ;':"EnterAltCV BNM,<.>/?ShiftAlt CtrlInsEnd4$5%^&9(0)-_=+LRXEsc F3 F4 F5 F6 F7 F8 F9 F10 F11 F12F1 F2 Fn123 /*-Tab QW895623PgUpCapsLock ASShiftCtrlPgDn+`~!@#Enter.Del8*Z$

3 - 9The keyboard keys are backlit. The keyboard backlight is manually controlled using the backlight key in the upper right hand corner of the keyboard. Pressing the backlight key cycles the keyboard backlight through the levels of backlight intensity: Off, Low intensity, Medium intensity, Maximum intensity, Off, etc. When the Thor VM3 is powered on, the key-board backlight defaults to Off.Since the keyboard is a USB device, by default the external keyboard backlight is turned off when the Thor VM3 enters Standby/Sleep. This behavior can be changed by enabling USB power in Standby/Sleep on the Options (page 5-23) control panel. USB Keyboard / MouseA standard USB keyboard or mouse can be attached to the Thor VM3 using the appropriate adapter cable.The Y cable attaches to the Thor VM3 and provides a USB connector. Please refer to documentation provided with the USB keyboard or mouse for more information on their operation.LED FunctionsSystem LEDsSYS (System Status) LEDLED Behavior System StateSolid Green • On• On but Display OffGreen blinking very slowlyExternal power present(1/2 sec. on, 4 1/2 sec. off) •OffExternal power present • OffConnection LEDsSystem LEDsBlue LED Orange LEDProgrammable LEDUPSSYSSSDSYS (System Status) LEDUPS (Uninterruptible Power Supply) LEDSSD (Solid State Drive) LED

3 - 10UPS Status LEDThe color of the UPS LED identifies the charge level, while the behavior of the LED identifies the charging state.Charge LevelCharging StateSSD (Solid State Drive) LEDOffExternal power not present • OffGreen blinking slowlyExternal power present(1/2 sec. on, 1 1/2 sec. off)CPU temperature less than -20ºC, Heater warming CPU for 30 sec.Green blinking slowlyExternal power not present(1/2 sec. on, 1 1/2 sec. off)CPU temperature less than -20ºC, Need to move unit to warmer environmentLED Color StatusGreen Fully charged (>90%)Amber • Less than fully charged, but more than 2 minutes runtime remaining• Out of Safe Charging Temperature Range (page 3-2) Charging only occurs between approximately -10°C and 35°C ambient temperature• No UPS present•Charging Timeout (page 3-3) Not fully charged after 4 or 8 hours depending on software revision.Red Low battery, less than 2 minutes runtime until shutdownLED Behavior StatusSlow Blink(1 sec. on, 3 sec. off) ChargingFast Blink(1/2 sec. on, 1/2 sec. off) UPS supplying power and dischargingOn Neither charging or dischargingOff Unit is off or is in SuspendLED Behavior StatusFlashing Green SSD read or write activityOff No SSD read or write activityLED Behavior System State

3 - 11Connection LEDsWWAN LEDWi-Fi LEDBluetooth LEDThe Bluetooth LED blinks once every 6 seconds when the Bluetooth client is paired but not connected. It blinks once for a very short time every 2 seconds when paired and connected. It blinks every second when in discovery. The LED is off when the Bluetooth client is off.LED Behavior StatusSolid Green Indicates a WWAN connection to a networkOff Indicates no WWAN connectionLED Behavior StatusSolid Green Indicates a connection with an IP address to an Access PointOff Indicates no connection to an Access PointLED Behavior StatusBlue Blinking Slowly Bluetooth is paired but not connected to a deviceBlue Blinking Medium Bluetooth is paired and connected to a deviceBlue Blinking Fast Bluetooth is discovering Bluetooth devicesOff Bluetooth hardware has been turned offWi FiWi-Fi LEDBluetooth LEDWWAN LED

3 - 12Keyboard LEDsThe keyboard LEDs are located near the specified key.Blue LEDOrange LEDProgrammable LEDThe Programmable LED is available for user applications. The LED defaults to Off unless activated by user applica-tion.DisplayThe display is a thin-film transistor display capable of supporting WSVGA graphics modes. Display size is 1024x768 pixels. The display covering is designed to resist stains. The touch screen allows signature capture and touch input. The display sup-ports screen blanking to eliminate driver distraction when the vehicle is in motion. Touch ScreenThe touch screen is a Resistive Panel with a scratch resistant finish that can detect touches by a stylus, and translate them into computer commands. In effect, it simulates a computer mouse. Only Delrin or plastic styluses should be used. A right mouse click is simulated by touching and holding the screen for the appropriate time interval. When a dialog box is too large for the display, tap and drag the dialog box up or down or from side to side to view the remainder of the dialog box.Always use the point of the stylus for tapping or making strokes on the display. Never use an actual pen, pencil, sharp or abrasive object to write on the touch screen. An extra or replacement stylus may be ordered. A replaceable touch screen protective film is available when the Thor VM3 is used in an abrasive environment. Contact Technical Assistance (page 6-1) for availability.Note: If the touch screen is disabled or looses calibration on a Thor VM3, you must use a USB mouse or keyboard attached to the Thor VM3 to access the control panel to re-enable or recalibrate the touch screen unless a programmable key has been assigned to that function.Touch Screen DefrosterExtended temperature versions of the Thor VM3 contain a touch screen defroster. The touch screen defroster can be dis-abled when not needed via the Screen Control (page 2-20) panel. The defroster trip point is configurable. The defroster is always disabled when the device is operating from UPS battery power.Solid Blue • Indicates the Blue modifier key is active• Pressing the Blue key a second time exits this modifier mode and turns off the LED• Pressing the Orange key exits the Blue mode and turns off the Blue LED• If no key other key is pressed within five seconds, the Blue key times out and turns off the LED• When Blue mode is active, keys P1 through P4 provide volume and brightness adjustment functionsOff Blue mode is not invokedLED Behavior StatusSolid Orange • Indicates the Orange modifier key is active. Orange mode is invoked for the next keypress only• Pressing the Orange key a second time exits this modifier mode and turns off the LED• Pressing the Blue key exits the Orange mode and turns off the Orange LEDOff Orange mode is not invoked.

3 - 13Screen BlankingScreen blanking (blackout) can be enabled when the vehicle is in motion. See Screen Blanking (page 1-38) for hardware setup and Screen Control (page 2-20) for software setup to enable screen blanking. Once screen blanking is enabled, the display is blanked out any time when the cable sends the signal the vehicle is in motion. If the cable is removed, screen blanking is disabled and the display remains on.Display Backlight ControlThe display brightness on a Thor VM3 equipped with an outdoor display can be configured to automatically adjust depend-ing on the ambient light level via Screen Control (page 2-20).Note: When automatic brightness control is enabled, the manual display brightness controls described below have no effect.The display brightness can be adjusted manually, via the keypad:1. Press the Blue key to enter Blue mode.2.3. Press P5 to increase brightness or P6 to decrease brightness.4. Press the Blue key to exit Blue mode.

1 - 151Vehicle Mounting and Accessory InstallationIntroductionThe Thor VM3 is designed to be mounted to a Quick Mount Smart Dock in a vehicle with either a RAM mount system. A power cable is provided with the Thor VM3 dock. Optional communication cables are available.Vehicle mounting brackets are specifically designed for vehicle mount applications. The vehicle mounted assembly restrains the Thor VM3 and isolates it from shock and vibration. A RAM metal table stand is available to secure the Thor VM3 and dock when in an office environment, for example.The vehicle mount holds the Quick Mount Smart Dock and the Thor VM3 attaches to the dock. The dock remains attached to the vehicle, however, the Thor VM3 has a quick release located on the lower rear side that allows the Thor VM3 to easily be removed from the dock. The Thor VM3 can be operated for a minimum of 30 minutes from an internal UPS battery when not attached to a dock. The Thor VM3 can be transferred from one dock equipped vehicle to another for easy portability. The dock provides accessory attachment and conditioned power for the Thor VM3.Overhead, dash and roof support pillar mounting is via a RAM Mount accessory which includes all the hardware required for vehicle mounting.Never put the Thor VM3 into the vehicle mounted assembly until the assembly is securely fastened to the vehicle.Prepare for Vehicle Mounting The Thor VM3 should be secured to an area in the vehicle where it:• Does not obstruct the driver's vision or safe vehicle operation.• Will be protected from rain or inclement weather.• Will be protected from extremely high concentrations of dust or wind-blown debris.• Can be easily accessed by a user seated in the driver's seat while the vehicle is not in operation. Quick StartThe following list outlines, in a general way, the process to follow when mounting the Thor VM3 in a vehicle. Refer to the fol-lowing sections in this document for more details.1. Install RAM Mount (page 1-18) to the vehicle.2. Place Thor VM3 in the Dock (page 1-16).3. Adjust the Thor VM3 to the best viewing angle.4. Install Remote Antenna (page 1-45) if necessary.5. Connect Cables (page 1-23) for any peripherals.6. Connect vehicle power:•12-48 VDC Vehicles (10-60 VDC Direct Connection) (page 1-25)•60-144 VDC Vehicles (50-150 VDC Power Supply, Screws on Top of Lid) (page 1-33)•60-144 VDC Vehicles (50-150 VDC Power Supply, Screws on Side of Lid) (page 1-29).•Thor VX8 / Thor VX9 Adapter Cable (page 1-37)•VX6 / VX7 Adapter Cable (page 1-36)7. Secure all cables in Strain Relief Cable Clamps (page 1-23).The Thor VM3 is ready for use.Maintenance - Vehicle Mounted DevicesCheck the vehicle mounting hardware frequently and re-tighten if necessary.If the vehicle mounting hardware and connections become broken, loose or cracked, the assembly must be taken out of service and replaced. Contact Technical Assistance (page 6-1) for help.

1 - 16CleaningDo not use paper towels or harsh-chemical-based cleaning fluids since they may result in damage to the Thor VM3 surfaces, cables, connectors and mounting hardware.Use a clean soft cloth to wipe any dirt, moisture or grease from the Thor VM3, connectors, cables or the vehicle mounting hard-ware. Do not use any liquid to clean the Thor VM3, or connectors. Spray or dampen the cleaning cloth with the cleaning liquid. If possible, clean only those areas which are soiled. Lint/particulates can be removed with clean, filtered canned air.Place Thor VM3 in the Dock1. Locate the notch on the upper rear of the Thor VM3.2. Slide this notch over the top lip of the dock. Slide the Thor VM3 from side to side on the dock to make sure it fully engages on the lip of the dock. If the Thor VM3 cannot be slid side to side, the lip is engaged.3. Pull the quick release lever on the Thor VM3 down and push the Thor VM3 against the dock.4. Release the quick release lever. The quick release lever catches the lower lip on the dock and secures the Thor VM3 to the dock.5. If necessary, adjust the viewing angle of the Thor VM3.When the Thor VM3 is placed in the dock, the following may happen:When the Thor VM3 is removed from the dock, the following may happen:Back of Thor VM3 Front of Quick Mount Smart DockNotch onThor VM3 Release LeverUpper Lip on DockLower Lip on Dock

1 - 17Dock I/O Pin Cover.PadlockLaptop Security CableThe dock contains a tethered I/O Pin Cover to protect the I/O pins on the dock when a Thor VM3 is not mounted in the dock.• When the Thor VM3 is not installed in the dock, use the I/O Pin Cover to protect the pins on the dock as shown.• When a Thor VM3 is installed in the dock, the I/O Pin Cover can be placed out of the way behind the dock.It may be desirable to secure the Thor VM3 in the dock so it cannot be removed from the dock. The quick release handle on the Thor VM3 is notched to allow a user supplied standard padlock to be placed through a hole in the bracket on the back of the Thor VM3 in the location shown below. Once the padlock is installed, the release handle cannot be moved so the Thor VM3 cannot be removed from the dock. The padlock shackle must be smaller than 3/16” (4.76mm).A cable tie wrap can be used instead of a padlock if desired.The Thor VM3 can be secured with a standard laptop security ca-ble using the slot on the back of the Thor VM3.

1 - 18Install RAM MountBefore installation begins, verify you have the applicable vehicle mounting bracket assembly components necessary, as shown in the following figures.Components - RAM Mounting KitsIn addition to the kits below, individual RAM mounting components are also available.Each mounting kit contains:CAUTION - This device is intended to transmit RF energy. For protection against RF exposure to humans and in accor-dance with FCC rules and Industry Canada rules, this transmitter should be installed such that a minimum separation dis-tance of at least 20 cm (7.8 in.) is maintained between the antenna and the general population. This device is not to be co-located with other transmitters.RAM Ball (Size D) for back of Thor VM3 Quick Mount Smart Dock with hardware (screws and washers) to attach RAM ball to dockRAM Arm (Size D), length varies by kit selectedOne of three mounting options:• RAM Ball mount (Size D, may include 3 cone washers), or• RAM Clamp mount (Size D), or• RAM Plate mount with RAM Ball (Size D) with Hardware (cone washers and nuts) to attach Ball to Plate

1 - 19Procedure - RAM Mount AssemblyEquipment Needed: Sockets, screwdriver and a Torque wrench capable of measuring to 50 inch pounds (5.64±.56 N/m).Note: Torquing tool is not supplied by Honeywell. Tools needed to attach the RAM Clamp Mount to the vehicle are not supplied by Honeywell.Torque MeasurementYou will need a torquing tool capable of torquing to 20 inch pounds (1.10 N/m). Torque all screws and bolts according to the following table:Step 1a – Attach RAM Ball to VehicleNote: If you are using the RAM clamp mount, please go to Step 1b – Mount RAM Clamp to Vehicle (page 1-20). If you are using the RAM plate mount, please go to Step 1c – Attach RAM Plate to Vehicle and Attach RAM Ball (page 1-21).1. Determine the position for mounting the RAM ball base. Be sure to position the RAM bracket to allow access to the switches and ports on the bottom of the Thor VM3.2. Attach the RAM ball base to the vehicle mounting surface using three or four 1/4 bolts (not included) or equivalent fasteners. If the mounting kit includes cone washers, use those as illustrated below. IMPORTANT: Mount to the most rigid surface available.Mounting DimensionsNote: Drill and tap holes for three 1/4 bolts. Drawing not to scale.For these nuts… Torque to10-32 lock nuts 17 - 20 in/lb (0-95 - 1.10 N/m)120º120º60º60º2.75" / 69.85 mm3.69" / 93.73 mm

1 - 20Step 1b – Mount RAM Clamp to VehicleNote: If you are using the RAM ball mount, please go to Step 1a – Attach RAM Ball to Vehicle (page 1-19). If you are using the RAM plate mount, please go to Step 1c – Attach RAM Plate to Vehicle and Attach RAM Ball (page 1-21).1. Determine the position for mounting the RAM clamp mount. The clamp mount can be used on a beam (such as on a fork lift truck) up to 2.5” (63.5 mm) wide and approximately 2” (50.8 mm) thick. The clamp may be attached to a thicker beam by substituting longer bolts (not included). Be sure to position the RAM clamp mount to allow access to the switches and ports on the bottom of the Thor VM3.2. Position the upper clamp piece with ball on the beam. Place the bolts through the holes in the upper clamp piece.3. Position the lower clamp piece below the beam. Align the bolts with the holes in the lower clamp piece.4. Place the nylon locking nuts on the bolts and tighten the bolts.Mounting DimensionsNote: Drawing not to scale.Upper clamp pieceBoltsLower clamp pieceNuts2.56” / 65.02mm1.84” (46.74mm)

1 - 21Step 1c – Attach RAM Plate to Vehicle and Attach RAM BallNote: If you are using the RAM ball mount, please go to Step 1a – Attach RAM Ball to Vehicle (page 1-19) If you are using the RAM clamp mount, please go to Step 1b – Mount RAM Clamp to Vehicle (page 1-20).1. Determine the position for mounting the RAM ball plate. Be sure to position the RAM plate to allow access to the switches and ports on the bottom of the Thor VM3.2. Attach the RAM ball plate to the vehicle mounting surface using four 1/4 bolts (not included) or equivalent fasten-ers.3. If not already attached, attach the RAM ball to the RAM ball plate using three M6 nuts and washers.IMPORTANT: Mount to the most rigid surface available.Mounting DimensionsThere are 4 mounting holes in the plate. Use four 1/4 bolts to secure the plate to the vehicle.Note: Drawing not to scale.176 mm6.99”200 mm7.87”76mm 2.99”100mm 3.94”

1 - 22Step 2 – Attach RAM Mount Ball to the Thor VM3 Quick Mount Smart Dock1. Turn the Thor VM3 off before attaching the RAM mount ball.2. Place the Thor VM3 face down on a stable surface.Step 3 – Attach Thor VM3 Assembly to RAM Mount1. Slip the Size D RAM arm over the ball on the vehicle RAM mount (RAM Ball mount shown).2. Insert the ball on the dock into the RAM arm and tighten the knob on the RAM arm using the supplied RAM wrench.Step 4 – Place the Thor VM3 into the DockIf the Thor VM3 is not already mounted to the dock, Place Thor VM3 in the Dock (page 1-16)

1 - 23Connect CablesThere are many cables available for the Thor VM3 including power cables, and data/ communication cablesThor VM3.Strain Relief Cable ClampsEquipment Required: Phillips screwdriver (not supplied by Honeywell)There are five strain relief cable clamps secured to the Thor VM3 Quick Mount Smart Dock.Use the strain relief clamps to secure audio, power, and I/O cables attached to the Thor VM3 dock.1. Determine the proper strain relief cable clamp. There are three sizes of cable clamps on the Thor VM3 which should be matched to the cable to be secured. For example, the largest clamp (on the left when viewing the back of the Thor VM3) is designed to secure the power cable.2. Remove the strain relief clamp from the Thor VM3 by turning the screw counterclockwise. Put the screw aside in a safe location.3. Slide the strain relief clamp over the cable.4. Using a Phillips screwdriver and the screw that was removed, refasten the clamp holding the cable to the Quick Mount. Do not stretch the cable. Leave enough slack in the cable to allow it to be connected and disconnected easily when needed.5. Continue in this manner until all cables are secured to the Thor VM3 dock.

1 - 24Connect PowerPower options include:•12-48 VDC Vehicles (10-60 VDC Direct Connection) (see page 1-25) - Direct connection to vehicle power.•60-144 VDC Vehicles (50-150 VDC Power Supply, Screws on Side of Lid) (see page 1-29) - Requires the use of a DC/DC power supply.•60-144 VDC Vehicles (50-150 VDC Power Supply, Screws on Top of Lid) (see page 1-33) - Requires the use of a DC/DC power supply.•VX6 / VX7 Adapter Cable (see page 1-36) - For applications where the Thor VM3 replaces a previously installed VX6 or VX7.•Thor VX8 / Thor VX9 Adapter Cable (see page 1-37) - For applications where the Thor VM3 replaces a previously installed Thor VX8 or Thor VX9.•Screen Blanking (see page 1-38) - Optional connection to blank the Thor VM3 display while the vehicle is in motion.•External AC/DC Power Supply (see page 1-41) - For use when DC power is not available to power the Thor VM3, such as in an office environment.See Power Supply Connector (page 5-5) for connector pinoutPower Cable CautionsPower Cable Routing CAUTION - When routing the power cable:• Route power cable away from the outside of the fork truck.• Choose a mounting location so that the power cable does not extend outside the vehicle and that provides sufficient clearance so that the power cable (especially the dock connector end) is not pressed against part of the vehicle.• Use the proper Strain Relief Cable Clamps (page 1-23) to secure cable.• The power cable is less flexible in low temperature environments. Avoid sharp bends.Regularly inspect power cable for damage, especially in low temperature environments. Contact Technical Assistance (page 6-1) for replacement cable options.!

1 - 2512-48 VDC Vehicles (10-60 VDC Direct Connection)Power Cable IdentificationNote: Correct electrical polarity is required for safe and proper installation. See the figures below for additional wire color-coding specifics.The Thor VM3 DC input wires (Red, Red/White DC+ and Black, Black/White DC-) and the Blue ignition input wire are galvanically isolated. The Green ground input is used for electrostatic discharge (ESD) protection. Vehicle 10-60VDC Direct Power Connection1. The Thor VM3 must not be mounted in the Quick Mount Smart Dock. The power switch on the dock must be turned Off. The power cable must be UNPLUGGED from the dock.2. While observing the Fuse Requirements (see page 1-25), connect the power cable as close as possible to the actual battery terminals of the vehicle (if using unswitched power). 3. Use proper electrical and mechanical fastening means for terminating the cable. Properly sized “crimp” type electrical terminals are an accepted method of termination. Please select electrical connectors sized for use with 20AWG (0.81mm2) conductors.4. Refer to the wiring diagrams following this section for wire colors and connections:•Ignition Control Wiring Diagram (page 1-27)•Auto-On Control Wiring Diagram (page 1-28)•Manual Control Wiring Diagram (page 1-29)CAUTION - For installation by trained service personnel only.Use caution when routing the power cable. See Power Cable Cautions (page 1-24).Fuse RequirementsWARNING - For proper and safe installation, the input power cable must be connected to a fused circuit on the vehicle. If the supply connection is made directly to the battery, the fuse should be installed in the positive lead within 5 inches (12.7 cm) of the battery’s positive (+) terminal. Use VM3055FUSEKIT to install this fuse or use equivalent 20A fast blow fuse.Note: For North America, a UL Listed fuse is to be usedThe Power cable has a right angle connector and 6 wires:Wire Color ConnectionRed DC + (10-60 VDC)Red/White DC + (10-60 VDC)Twist the red and red/white wires together and twist the black and black/white wires together before connecting to vehicle power.Black DC -Black/White DC -Green GroundBlue Ignition Input (optional)!!!!

1 - 265. Route the power cable the shortest way possible removing any left-over cable. The cable is rated for a maxi-mum temperature of 105°C (221°F). Therefore, when routing this cable it should be protected from physical damage and from surfaces that might exceed this temperature. Cable should be protected from physical damage from moving parts. Do not expose the cable to chemicals or oil that may cause the wiring insulation to deteriorate. Always route the cable so that it does not interfere with safe operation and maintenance of the vehicle. 6. Provide mechanical support for the cable by securing it to the vehicle structure at approximately one foot inter-vals, taking care not to over tighten and pinch conductors or penetrate outer cable jacket.7. Connect the watertight connector end of the power cable to the Thor VM3 Quick Mount Smart Dock power connector by aligning the connector pins to the power connector; push down on the watertight connector and twist it to fasten securely.8. Secure the power cable to the Thor VM3 using the Strain Relief Cable Clamps (page 1-23).9. Place Thor VM3 in the Dock (page 1-16)10. If using the Screen Blanking (page 1-38) feature, install the screen blanking box or switch.11. Press the Power Switch (page 3-4) on the back of the Thor VM3 dock.12. Press the Power Button (page 3-4) on the front of the Thor VM3 to turn on the Thor VM3.

1 - 27Ignition Control Wiring Diagram.CAUTIONFor battery powered vehicles:• Red wire is connected to battery positive. If there is a red wire and a red/white wire, twist them together and connect to battery positive.• Black wire must be connected to battery negative. If there is a black wire and a black/white wire, twist them together and connect to battery negative.• Green wire must be connected to the vehicle chassis ground.For internal combustion engine powered vehicles:• Red wire is connected to battery positive. If there is a red wire and a red/white wire, twist them together and connect to battery positive.• Black wire must be connected to battery negative. If there is a black wire and a black/white wire, twist them together and connect to battery negative.• Green wire is connected to the vehicle chassis ground, which can also be battery negative.Fuse RequirementsWARNING - For proper and safe installation, the input power cable must be connected to a fused circuit on the vehicle. If the supply connection is made directly to the battery, the fuse should be installed in the positive lead within 5 inches (12.7 cm) of the battery’s positive (+) terminal. Use VM3055FUSEKIT to install this fuse or use equivalent 20A fast blow fuse.Note: For North America, a UL Listed fuse is to be used.Existing Circuitry On VehicleBatteryMain Switch-Vo+VoFuse - SeeWarning statement below IgnitionSee Caution statement belowQuick MountSmart DockCircularPowerConnectorCOM1 or COM2ConnectorCable for optionalscreen blankingconnectionRedBlackGreenBlueRed/White (if present)Black/White (if present)!!

1 - 28Auto-On Control Wiring Diagram.CAUTIONFor battery powered vehicles:• Red wire is connected to battery positive. If there is a red wire and a red/white wire, twist them together and connect to battery positive.• Black wire must be connected to battery negative. If there is a black wire and a black/white wire, twist them together and connect to battery negative.• Green wire must be connected to the vehicle chassis ground.For internal combustion engine powered vehicles:• Red wire is connected to battery positive. If there is a red wire and a red/white wire, twist them together and connect to battery positive.• Black wire is connected to battery negative. If there is a black wire and a black/white wire, twist them together and connect to battery negative.• Green wire is connected to the vehicle chassis ground, which can also be battery negative.Fuse RequirementsWARNING - For proper and safe installation, the input power cable must be connected to a fused circuit on the vehicle. If the supply connection is made directly to the battery, the fuse should be installed in the positive lead within 5 inches (12.7 cm) of the battery’s positive (+) terminal. Use VM3055FUSEKIT to install this fuse or use equivalent 20A fast blow fuse.Note: For North America, a UL Listed fuse is to be usedQuick MountSmart DockCircularPowerConnectorCOM1 or COM2ConnectorExisting Circuitry On VehicleBatteryMain Switch-Vo+Vo Cable for optionalscreen blankingconnectionSee Caution statement belowFuse - SeeWarning statement below (not connected)RedBlackGreenBlueRed/White (if present)Black/White (if present)!!

1 - 29Manual Control Wiring Diagram60-144 VDC Vehicles (50-150 VDC Power Supply, Screws on Side of Lid)This option requires DC/DC external power supply Honeywell Part no. 9000313PWRSPLY.CAUTIONFor battery powered vehicles:• Red wire is connected to battery positive. If there is a red wire and a red/white wire, twist them together and connect to battery positive.• Black wire must be connected to battery negative. If there is a black wire and a black/white wire, twist them together and connect to battery negative.• Green wire must be connected to the vehicle chassis ground.For internal combustion engine powered vehicles:• Red wire is connected to battery positive. If there is a red wire and a red/white wire, twist them together and connect to battery positive.• Black wire is connected to battery negative. If there is a black wire and a black/white wire, twist them together and connect to battery negative.• Green wire is connected to the vehicle chassis ground, which can also be battery negative.Fuse RequirementsWARNING - For proper and safe installation, the input power cable must be connected to a fused circuit on the vehicle. If the supply connection is made directly to the battery, the fuse should be installed in the positive lead within 5 inches (12.7 cm) of the battery’s positive (+) terminal. Use VM3055FUSEKIT to install this fuse or use equivalent 20A fast blow fuse.Note: For North America, a UL Listed fuse is to be usedQuick MountSmart DockCircularPowerConnectorCOM1 or COM2ConnectorExisting Circuitry On VehicleBatteryMain Switch-Vo+Vo Cable for optionalscreen blankingconnectionSee Caution statement belowFuse - SeeWarning statement below (not connected)RedBlackGreenBlueRed/White (if present)Black/White (if present)!!

1 - 30If the DC/DC power supply does not have screws in the side of the lid, see 60-144 VDC Vehicles (50-150 VDC Power Supply, Screws on Top of Lid) (page 1-33).Power Cable IdentificationNote: Correct electrical polarity is required for safe and proper installation. See Wiring Diagram (page 1-32) for additional wire color-coding specifics.The Thor VM3 DC input wires (Red, Red/White DC+ and Black, Black/White DC-) and the Blue ignition input wire are galvanically isolated. The Green ground input is used for electrostatic discharge (ESD) protection.Vehicle 50-150VDC Power Connection1. Please review the Wiring Diagram (page 1-32), before beginning power cable install. 2. The Thor VM3 must not be mounted in the Quick Mount Smart Dock. The power switch on the dock must be turned Off. The power cable must be UNPLUGGED from the dock.3. Route the cable from the Thor VM3 to the DC/DC power supply. Route the power cable the shortest way pos-sible. The cable is rated for a maximum temperature of 105°C (221°F). When routing this cable, it should be protected from physical damage and from surfaces that might exceed this temperature. Do not expose the cable to chemicals or oil that may cause the wiring insulation to deteriorate. Always route the cable so that it does not interfere with safe operation and maintenance of the vehicle.4. Cut the cable to length and strip the wire ends.5. Remove the lid from the DC/DC power supply.6. Connect the stripped end of the positive wires (red and red/white twisted together or a single red wire) to the output block. See Power Cable Identification (page 1-30).Shown With Lid Attached• Lid is secured with screws on the side of lid.Shown With Lid Removed• Input and output connector blocks under lid.• One positive (Vin+), negative (Vin-) and ground ( ) connection in input block. • One positive (Vo+) and negative (Vo-) connection in output block.CAUTION - For installation by trained service personnel only.CAUTION - Usage in areas where moisture can affect the power supply connections should be avoided. The power supply should be mounted in a dry location within the vehicle or placed in a suitable protective enclosure.Use caution when routing the power cable. See Power Cable Cautions (page 1-24).Fuse RequirementsWARNING - For proper and safe installation, the input power cable must be connected to a fused circuit on the vehicle. If the supply connection is made directly to the battery, the fuse should be installed in the positive lead within 5 inches (12.7 cm) of the battery’s positive (+) terminal. Use VM3055FUSEKIT to install this fuse or use equivalent 20A fast blow fuse.Note: For North America, a UL Listed fuse is to be usedThe power cable has a right angle connector and 6 wires:Wire Color ConnectionRed (2 wires) DC + (10-60 VDC)Black (2 wires) DC -Twist the red and red/white wires together and twist the black and black/white wires together before connecting to vehicle power.Green GroundBlue Ignition Input (not used)!!!!!

1 - 317. Connect the stripped end of the negative wires (black and black/white twisted together or a single black wire) to the output. See Power Cable Identification (page 1-30).Note: The input block has VIN+, VIN- and GND terminals. The output block has VO+ and VO- terminals.8. Connect the ground (green) wire from the Thor VM3 to the GND terminal on the input side of the DC/DC power supply.9. Route the wiring from the DC/DC power supply to the vehi-cle’s electrical system. Do not connect to vehicle power at this time.10. Strip the wire ends and connect to the input side of the DC/DC power supply.11. Use looms and wire ties to secure all wiring as shown. 12. Reattach the cover with the screws.13. Connect the DC/DC power supply to the vehicle’s electrical system as directed below:14. While observing the Fuse Requirements (see page 1-33) connect the power cable as close as possible to the actual battery terminals of the vehicle. When available, always connect to unswitched terminals in the vehicle fuse panel, after providing proper fusing.ATTENTION: For uninterrupted power, electrical supply connections should not be made at any point after the ignition switch of the vehicle.15. Use proper electrical and mechanical fastening means for terminating the cable. Properly sized “crimp” type electrical terminals are an accepted method of termination. Select electrical connectors sized for use with 18AWG (1mm2) conductors.16. Provide mechanical support for the cable by securing it to the vehicle structure at approximately one foot inter-vals, taking care not to over tighten and pinch conductors or penetrate the outer cable jacket.17. Connect the watertight connector end of the power cable to the Thor VM3 Quick Mount Smart Dock power connector by aligning the connector pins to the power connector; push down on the watertight connector and twist it to fasten securely.Flip the power switch on the back of the dock to On.18. Secure the power cable to the Thor VM3 using the Strain Relief Cable Clamps (page 1-23).19. Place Thor VM3 in the Dock (page 1-16)20. If using the Screen Blanking (page 1-38) feature, install the screen blanking box or switch.21. Press the Power Switch (page 3-4) on the back of the Thor VM3 dock.22. Press the Power Button (page 3-4) on the front of the Thor VM3 to turn on the Thor VM3.Note: Ignition control is not available for trucks over 60VDC.For battery powered vehicles:VIN+ is connected to battery positive.ViN- must be connected to battery negative.GND must be connected to the vehicle chassis ground.For internal combustion engine powered vehicles:VIN+ is connected to battery positive.ViN- is connected to battery negative.GND is connected to the vehicle chassis ground, which can also be battery negative.!

1 - 32Wiring DiagramCAUTIONFor battery powered vehicles:GND must be connected to the vehicle chassis ground.For internal combustion engine powered vehicles:GND is connected to the vehicle chassis ground, which can also be battery negative.Fuse RequirementsWARNING - For proper and safe installation, the input power cable must be connected to a fused circuit on the vehicle. If the supply connection is made directly to the battery, the fuse should be installed in the positive lead within 5 inches (12.7 cm) of the battery’s positive (+) terminal. Use VM3055FUSEKIT to install this fuse or use equivalent 20A fast blow fuse.Note: For North America, a UL Listed fuse is to be used.Main SwitchCircularPowerConnectoron DockVIN-VO--Vo+Vo COM1 or COM2Connectoron DockVO+VIN+GNDUser supplied serialcable for optionalscreen blankingconnection,see belowExisting Circuitry on VehicleForklift BatteryDC/DCPowerSupplyFuse - SeeWarning statement below See Caution statementbelow (not connected)BlackGreenBlueRedRed/White (if present)Black/White (if present)Quick MountSmart Dock!!

1 - 3360-144 VDC Vehicles (50-150 VDC Power Supply, Screws on Top of Lid)This option requires DC/DC power supply Honeywell Part no. VX89303PWRSPLY, shown below.If the DC/DC power supply does not have screws in the top of the lid, see 60-144 VDC Vehicles (50-150 VDC Power Supply, Screws on Side of Lid) (page 1-29).Power Cable IdentificationNote: Correct electrical polarity is required for safe and proper installation. See Wiring Diagram (page 1-35) for additional wire color-coding specifics.The Thor VM3 DC input wires (Red, Red/White DC+ and Black, Black/White DC-) and the Blue ignition input wire are galvanically isolated. The Green ground input is used for electrostatic discharge (ESD) protection.Shown With Lid Attached• Lid is secured with screws on the top of lid.Shown With Lid Removed• Input and output connector blocks under lid.• Two positive (+), negative (-) and ground ( ) connections per terminal blockCAUTION - For installation by trained service personnel only.CAUTION - The VX89303PWRSPLY power supply is sealed per IPXX. Usage in areas where moisture can affect the power supply connections should be avoided. The power supply should be mounted in a dry location within the vehicle or placed in a suitable protective enclosure.Use caution when routing the power cable. See Power Cable Cautions (page 1-24).Fuse RequirementsWARNING - For proper and safe installation, the input power cable must be connected to a fused circuit on the vehicle. If the supply connection is made directly to the battery, the fuse should be installed in the positive lead within 5 inches (12.7 cm) of the battery’s positive (+) terminal. Use VM3055FUSEKIT to install this fuse or use equivalent 20A fast blow fuse.Note: For North America, a UL Listed fuse is to be used.The power cable has a right angle connector and 6 wires:Wire Color ConnectionRed (2 wires) DC + (10-60 VDC)Black (2 wires) DC -Twist the red and red/white wires together and twist the black and black/white wires together before connecting to vehicle power.Green GroundBlue Ignition Input (not used)!!!!!

1 - 34Vehicle 50-150VDC Power Connection1. Please review the Wiring Diagram (page 1-32), before beginning power cable install. 2. The Thor VM3 must not be mounted in the Quick Mount Smart Dock. The power switch on the dock must be turned Off. The power cable must be UNPLUGGED from the dock.3. Route the cable from the Thor VM3 to the DC/DC power supply. Route the power cable the shortest way pos-sible. The cable is rated for a maximum temperature of 105°C (221°F). When routing this cable, it should be protected from physical damage and from surfaces that might exceed this temperature. Do not expose the cable to chemicals or oil that may cause the wiring insulation to deteriorate. Always route the cable so that it does not interfere with safe operation and maintenance of the vehicle.4. Cut the cable to length and strip the wire ends.5. Remove the lid from the DC/DC power supply.6. Connect the stripped end of the positive wires (red and red/white twisted together or a single red wire) to the output block. See Power Cable Identification (page 1-33).7. Connect the stripped end of the negative wires (black and black/white twisted together or a single black wire) to the output. See Power Cable Identification (page 1-33).Note: The input and output blocks each have two + (plus), two – (minus) and two (ground) connectors. Either connector in the block can be used to connect the matching polarity wire.8. Route the wiring from the DC/DC power supply to the vehi-cle’s electrical system. Do not connect to vehicle power at this time.9. Strip the wire ends and connect to the input side of the DC/DC power supply.10. Use looms and wire ties to secure all wiring as shown. 11. Reattach the cover with the screws.12. Connect the DC/DC power supply to the vehicle’s electrical system as directed below13. While observing the Fuse Requirements (see page 1-33), connect the power cable as close as possible to the actual battery terminals of the vehicle. When available, always connect to unswitched terminals in the vehicle fuse panel, after providing proper fusing.ATTENTION: For uninterrupted power, electrical supply connections should not be made at any point after the ignition switch of the vehicle.14. Use proper electrical and mechanical fastening means for terminating the cable. Properly sized “crimp” type electrical terminals are an accepted method of termination. Select electrical connectors sized for use with 18AWG (1mm2) conductors.15. Provide mechanical support for the cable by securing it to the vehicle structure at approximately one foot inter-vals, taking care not to over tighten and pinch conductors or penetrate the outer cable jacket.16. Connect the watertight connector end of the power cable to the Thor VM3 Quick Mount Smart Dock power connector by aligning the connector pins to the power connector; push down on the watertight connector and twist it to fasten securely.Flip the power switch on the back of the dock to On.For battery powered vehicles:+ is connected to battery positive.- must be connected to battery negative.: must be connected to the vehicle chassis ground.For internal combustion engine powered vehicles:+ is connected to battery positive.- is connected to battery negative. is connected to the vehicle chassis ground, which can also be battery negative.!

1 - 3517. Secure the power cable to the Thor VM3 using the Strain Relief Cable Clamps (page 1-23).18. Place Thor VM3 in the Dock (page 1-16)19. If using the Screen Blanking (page 1-38) feature, install the screen blanking box or switch.20. Press the Power Switch (page 3-4) on the back of the Thor VM3 dock.21. Press the Power Button (page 3-4) on the front of the Thor VM3 to turn on the Thor VM3.Note: Ignition control is not available for trucks over 60VDC.Wiring DiagramCAUTIONFor battery powered vehicles: must be connected to the vehicle chassis ground.For internal combustion engine powered vehicles: is connected to the vehicle chassis ground, which can also be battery negative.Fuse RequirementsWARNING - For proper and safe installation, the input power cable must be connected to a fused circuit on the vehicle. If the supply connection is made directly to the battery, the fuse should be installed in the positive lead within 5 inches (12.7 cm) of the battery’s positive (+) terminal. Use VM3055FUSEKIT to install this fuse or use equivalent 20A fast blow fuse.Note: For North America, a UL Listed fuse is to be used.PowerConnector---VoBlackGreenBlue(not connected)+Vo COM1 or COM2Connector++User supplied serialcable for optionalscreen blankingconnection,see belowExisting Circuitry on VehicleForklift BatteryMain SwitchQuick MountSmart DockDC/DCPowerSupplyFuse - SeeWarning statement below See Caution statement below RedRed/White (if present)Black/White (if present)!!

1 - 36VX6 / VX7 Adapter CableAn adapter cable is available to attach the Thor VM3 to a vehicle previously equipped with a VX6/VX7 DC power cable. The adapter cable has a 5-pin connector to match with the VX6/VX7 power supply cable on one end and a 6-pin con-nector to match to the Thor VM3 on the other end. This section assumes the VX6/VX7 power cable is properly con-nected to vehicle power. Refer to the VX6 or VX7 Vehicle Mounting Reference Guide for details.When this adapter cable is used, there is no provision for an ignition switch input. Therefore the vehicle ignition moni-toring function is not available when using this cable.Connect to VX6 / VX7 Power Cable1. Connect the cable to the Thor VM3 power cable by aligning the connector pins to the power connector; push down on the watertight connector and twist it to fasten securely.2. The cable is rated for a maximum temperature of 105°C (221°F). Therefore, routing this cable it should be protected from physical damage and from surfaces that might exceed this temperature. Cable should be pro-tected from physical damage from moving parts. Do not expose the cable to chemicals or oil that may cause the wiring insulation to deteriorate. Always route the cable so that it does not interfere with safe operation and maintenance of the vehicle. 3. Provide mechanical support for the cable by securing it to the vehicle structure at approximately one foot inter-vals, taking care not to over tighten and pinch conductors or penetrate outer cable jacket.4. Connect the watertight connector end of the power cable to the Thor VM3 Quick Mount Smart Dock power connector by aligning the connector pins to the power connector; push down on the watertight connector and twist it to fasten securely.5. Secure the power cable to the Thor VM3 using the Strain Relief Cable Clamps (page 1-23).6. Place Thor VM3 in the Dock (page 1-16)7. If using the Screen Blanking (page 1-38) feature, install the screen blanking box or switch.8. Press the Power Switch (page 3-4) on the back of the Thor VM3 dock.9. Press the Power Button (page 3-4) on the front of the Thor VM3 to turn on the Thor VM3.CAUTION - Because the Thor supports 10-60 VDC power input, verify input voltages before using this adapt-er cable with an existing VX6 or VX7 power connection installation.!To Power Connector on DockTo VX6/VX7 Power Supply Cable

1 - 37Thor VX8 / Thor VX9 Adapter CableAn adapter cable is available to attach the Thor VM3 to a vehicle previously equipped with a VX8/VX9 DC power cable. The adapter cable has a 6-pin connector to match the VX8/XVX9 power supply cable on one end and a 6-pin connec-tor to match the Thor VM3 on the other end. The cable also has bare wires for ground and ignition sense connection plus a D9 cable to connect to a COM port on the Thor VM3 dock to provide a screen blanking signal. This section assumes the VX8/VX9 power cable is properly connected to vehicle power. Refer to the VX8 or VX9 Vehicle Mounting Reference Guide for details.Connect to Thor VX8 / VX9 Power Cable1. Connect the cable to the Thor VX8/VX9 power cable by aligning the connector pins to the power connector; push down on the watertight connector and twist it to fasten securely.2. Connect the green wire to vehicle ground:3. If ignition control will be used, connect the blue wire to an ignition switched circuit (less than 1mA over input voltage range). If ignition control is not used, the blue wire can be left disconnected,4. If the VX8/VX9 cable is connected to a screen blanking box or switch, connect the D9 connector to a COM port on the dock.5. The cable is rated for a maximum temperature of 105°C (221°F). Therefore, when routing this cable it should be protected from physical damage and from surfaces that might exceed this temperature. Cable should be protected from physical damage from moving parts. Do not expose the cable to chemicals or oil that may cause the wiring insulation to deteriorate. Always route the cable so that it does not interfere with safe opera-tion and maintenance of the vehicle. 6. Provide mechanical support for the cable by securing it to the vehicle structure at approximately one foot inter-vals, taking care not to over tighten and pinch conductors or penetrate outer cable jacket.7. Connect the watertight connector end of the power cable to the Thor VM3 Quick Mount Smart Dock power connector by aligning the connector pins to the power connector; push down on the watertight connector and twist it to fasten securely.8. Secure the power cable to the Thor VM3 using the Strain Relief Cable Clamps (page 1-23).9. Place Thor VM3 in the Dock (page 1-16)10. If using the Screen Blanking (page 1-38) feature, install the screen blanking box or switch if not previously installed.11. Press the Power Switch (page 3-4) on the back of the Thor VM3 dock.12. Press the Power Button (page 3-4) on the front of the Thor VM3 to turn on the Thor VM3.For battery powered vehicles:The green wire must be connected to the vehicle chassis ground.For internal combustion engine powered vehicles:The green wire is connected to the vehicle chassis ground, which can also be battery negative.To COM port on DockTo Power Connectoron DockTo VX8/VX9Power CableTo Ground andIgnition Sense!

1 - 38Screen BlankingPrerequisite: The steps outlined in either 12-48 VDC Vehicles (10-60 VDC Direct Connection) (page 1-25), 60-144 VDC Vehicles (50-150 VDC Power Supply, Screws on Side of Lid) (page 1-29) or 60-144 VDC Vehicles (50-150 VDC Power Supply, Screws on Top of Lid) (page 1-33) have been completed.Screen blanking is accomplished by either a Screen Blanking Box or a user supplied switch.Screen Blanking CableRefer to Screen Control (in the Windows Control Panel) to configure the Thor VM3 for screen blanking.When routing any additional cables for screen blanking:• Route the cable the shortest way possible removing any left-over cable• Fuses and cabling are user supplied. Therefore, route these cables so they are protected from physical damage and from surfaces that might exceed the cable's rated temperature threshold.• Cable should be protected from physical damage from moving parts• Do not expose the cable to chemicals or oil that may cause the wiring insulation to deteriorate• Always route the cable so that it does not interfere with safe operation and maintenance of the vehicle.• Provide mechanical support for the cable by securing it to the vehicle structure at approximately one foot intervals, taking care not to over tighten and pinch conductors or penetrate outer cable jacket.Honeywell Screen Blanking Box CableAn optional Honeywell Screen Blanking Box Cable is available.Note: Wire colors only apply to optional Honeywell Screen Blanking Box Cable, VM1080CABLE. Wire colors may vary in a user-supplied cable.The optional Honeywell Screen Blanking Box Cable, VM1080CABLE, is installed as follows:1. Connect the gray wire of the cable to the switched side of the Screen Blanking Box.2. Connect the black wire of the cable to the unswitched side of the Screen Blanking Box.3. Connect the D9 serial connector to either COM1 or COM2 serial port on the Thor VM3 Quick Mount Smart Dock.CAUTION - For installation by trained service personnel only.CAUTION - For proper and safe installation, the input power lead to the Screen Blanking Box requires a 3 Amp maximum time delay (slow blow) high interrupting rating fuse. Note: For North America, a UL Listed fuse is to be used.DB9 Female Function with Screen Blanking Box Wire color 1 -6, 9 Not Used 7 (RTS) Connected to Screen Blanking Box, unswitched side Black (see note)8 (CTS) Connected to Screen Blanking Box, switched side Gray (see note)!!

1 - 39User-Supplied CableA user-supplied cable can be used as well. Pins 7 and 8 must be connected as detailed below. No other pins are to be connected.The user-supplied cable is installed as follows:1. Connect the wire from Pin 8 of the cable to the switched side of the Screen Blanking Box or to a user-sup-plied switch.2. Connect the wire from Pin 7 of the cable to the unswitched side of the Screen Blanking Box or to a user-supplied switch.3. Connect the D9 serial connector to either COM1 or COM2 serial port on the Thor VM3 Quick Mount Smart Dock.Screen Blanking BoxIt is assumed that the motion sensing circuitry in the illustrations below is powered by internal vehicle circuitry.Please refer to the appropriate illustration below for Screen Blanking Box wiring diagrams.DB9 Female Function with Screen Blanking Box Function with Switch1 -6, 9 Not Used Not Used7 (RTS) Connected to Screen Blanking Box, unswitched side Connected to Switch8 (CTS) Connected to Screen Blanking Box, switched side Connected to SwitchScreen Blanking Box Terminal Connection12-xxV Input from vehicle motion sensing circuitry.Please refer to label on Screen Blanking Box for allowable voltage input range.GND DC -These two terminals are for connecting a serial cable:• If using an optional Honeywell screen blanking cable, VM1080CABLE, connect the gray wire to the switched side of the connection and connect the black wire to the unswitched side.• If using a user-supplied cable, the cable must be constructed so that Pin 7 (RTS) connects to switched side of the connection and Pin 8 (CTS) connects to the unswitched side.CAUTION - Do not exceed the maximum input voltage, either 60 or 72VDC, specified on the Screen Blanking Box label when using this configuration.PIN7PIN 8PIN 5 PIN1Unswitched Switched!

1 - 40Note: The black and gray wire colors in the illustration only apply to the optional Honeywell Screen Blanking Box Cable, VM1080CABLE. The wire colors may be different in a user-supplied cable.Screen Blanking with SwitchIn applications where it is impractical to use the screen blanking box due to vehicle voltage or lack of a motion sensing signal, screen blanking can be controlled via a user supplied switch or relay that provides an electrical conductive connection on vehicle motion.Pins 7 and 8 must be connected as shown in the illustration above. No other pins are to be connected.MOTIONCIRCUITRYTo-Vo on vehicle,i.e. Negativebattery terminal3A fuse+ViGNDTo pin 7 of COM1 orCOM2To pin 8 of COM1 orCOM2To pins 7 and 8of COM1 orCOM2port on dock

1 - 41External AC/DC Power SupplyThe optional external AC/DC power supply is for use in environments, such as an office, where DC power is not avail-able.Note: The Honeywell-approved AC/DC Power Supply and Adapter Cable are only intended for use in a 25ºC (77ºF) maximum ambient temperature environment.In North America, this unit is intended for use with a UL Listed ITE power supply with output rated 10 – 60 VDC, mini-mum 15W. Outside North America, this unit is intended for use with an IEC certified ITE power supply with output rated 10 – 60 VDC, minimum 15W.The external power supply may be connected to either a 120V, 60Hz supply or, outside North America, to a 230V, 50Hz supply, using the appropriate detachable cordset. In all cases, connect to a properly grounded source of supply provided with maximum 15 Amp overcurrent protection (10 Amp for 230V circuits).Connect External Power Supply1. Connect the provided detachable cordset (US only, all others must order cable separately) to the external power supply (IEC 320 connector).2. Plug cordset into appropriate, grounded, electrical supply receptacle (AC mains).3. Connect the DC Output Cable end to the corresponding connector on the Adapter Cable.4. Connect the watertight connector end of the Adapter Cable to the Thor VM3 Quick Mount Smart Dock Power Connector by aligning the connector pins to the power connector; push down on the watertight connector and twist it to fasten securely.5. Press the Power Switch (page 3-4) on the back of the Thor VM3 dock.6. Press the Power Button (page 3-4) on the front of the Thor VM3 to turn on the Thor VM3.AC Input Cable (US only) DC Output CableTo DC Output Cable To Dock

1 - 42Connect USB HostSee USB Connector (page 5-6) for connector pinouts.1. Seat the D9 connector firmly over the USB (or USB1) Connector on the Quick Mount Smart Dock.2. Tighten the thumbscrews in a clockwise direction. Do not over tighten.3. The USB-host connector provides a connector for a USB device such as a USB thumb drive.4. Secure the cables to the Thor VM3 with Strain Relief Cable Clamps (page 1-23).Connect USB ClientConnect Serial DeviceSee COM1 and COM2 Connector (page 5-5) for connector pinouts.1. Seat the cable end connector firmly over the serial COM port on the Quick Mount Smart Dock. 2. Turn the thumbscrews in a clockwise direction. Do not over tighten.3. Secure the cables to the Thor VM3 with Strain Relief Cable Clamps (page 1-23).4. Connect the other cable end to the desired serial device.Connect a Tethered Scanner1. The scanner cable is attached to either the COM1 or COM2 port on the Quick Mount Smart Dock.2. Connect the serial cable for the scanner as directed above.3. When the Thor VM3 is powered on, it provides power to the serial scanner.4. Configure the Data Collection (DC) Wedge to manipulate scanned data as desired.D9 Connector USB Host ConnectorUSB Client ConnectorD9 Connector USB Host ConnectorUSB Client Connector

1 - 43Connect Headset CableThe CANbus/Audio connector supports a headset adapter cable or a CANbus cable. The Thor VM3 does not support con-necting audio and CANbus simultaneously.See CANbus / Audio Connector (page 5-9) for connector pinouts.1. Seat the D15 cable end connector firmly over the CANbus/Audio Connector on the Quick Mount Smart Dock.2. Tighten the thumbscrews in a clockwise direction. Do not over tighten.3. Slide the cable ends together until they click shut. Do not twist or bend the connectors. The Thor VM3 internal microphone and speakers are automatically disabled when the headset is connected.Adjust Headset / Microphone and Secure CableThe headset consists of an earpiece, a microphone, a clothing clip and a cable.HeadphonesMicrophone To Audio cableTo Audio connectoron dockTo headsetclick!

1 - 441. Do not twist the microphone boom when adjusting the microphone. The microphone should be adjusted to be about two finger widths from your mouth. 2. Make sure the microphone is pointed at your mouth. Note the small “Talk” label near the mouthpiece. Make sure the Talk label is in front of your mouth. The microphone cable can be routed over or under clothing. 3. Follow the safety guidelines below when wearing the headset.Under Clothing• Leave the cable exposed only at the top of the collar. • Be sure to leave a small loop of cable to allow movement of your head. Over Clothing• Use clothing clips to hold the cable close to your body. • Tuck the cable under the belt, but leave a small loop where it goes under the belt. • Do not wear the cable on the front of your body. It may get in your way or get caught on protruding objects. Connect CANbus CableThe CANbus/Audio connector supports a headset adapter cable or a CANbus Y cable. The Thor VM3 does not support connecting audio and CANbus simultaneously.See CANbus / Audio Connector (page 5-9) for connector pinouts.1. Seat the D15 cable end connector firmly over the CANbus/Audio Connector on the Quick Mount Smart Dock.2. Tighten the thumbscrews in a clockwise direction. Do not over tighten.3. The CANbus Y cable has a 9 pin F SAE J1939 (Deutsch) and 9 pin M SAE J1939 (Deutsch) connector. Connect the appropriate cable connector as needed.

1 - 45Install Remote AntennaRemote antennas are available for the 802.11 WLAN radio, the WWAN radio and the GPS.802.11 Remote Mount AntennaComponents and Mounting DiagramThe Remote Antenna Installation Kit consists of two brackets (base plate and right angle), cable, and antenna. Tools are not included.The desired remote antenna bracket is mounted on the top of a forklift, truck or other vehicle and cabled to the Thor VM3 inside the vehicle.The Vehicle Remote Mount Antenna cannot be used by devices with an internal antenna.Nut WasherWasher BracketTo antennaTo antenna connector on computerBracketTo antennaAntenna

1 - 46Typical InstallationMounting Instructions1. Attach and secure the desired mounting bracket to the highest point on the safety cage, following these pre-cautions:• The plate must be mounted so the antenna is not damaged while the vehicle or any of its parts are moving.• The antenna mounting portion of the bracket must be parallel to the floor.• If using two antennas, they must be mounted at least 12 inches (304.8mm) apart.2. Attach the female connector of the coaxial cable to the antenna connector on the vehicle mounted Thor VM3.3. Secure the whip antenna to the mounting bracket.4. Connect the antenna cable to the whip antenna.5. Use cable ties to secure the coaxial cable to the vehicle as necessary. Make sure the cable is routed so it is not damaged by any moving parts of the vehicle.6. Connect the cable to the antenna connector (Wi-Fi Main or Wi-Fi Aux) on the Thor VM3. If only one antenna is used, be sure to connect it to the Wi-Fi Main connector.7. Repeat the steps above for the second 802.11 antenna.Antenna Mounting BracketVehicle Safety Cage Cable Vehicle MountedComputer

1 - 47WAN Remote Mount AntennaThe WAN remote mount antenna can be either a magnetic mount or an adhesive mount antenna.The Remote Antenna Installation Kit consists of the WAN antenna and an extension cable. The remote antenna is mounted on the top of a forklift, truck or other vehicle and cabled to the Thor VM3 inside the vehicle.1. Locate a mounting position on highest point on the vehicle, following these precautions:• The antenna must be mounted so the antenna is not damaged while the vehicle or any of its parts are moving.2. Clean the area where the antenna is to be mounted.3. If using an adhesive mount antenna, remove the protective backing paper from the adhesive on the antenna.4. Position the antenna on the vehicle.5. Attach the one end of the coaxial cable to the antenna and the other end to the Mobile Net WWAN connector on the vehicle mounted Thor VM3.6. Use cable ties to secure the coaxial cable to the vehicle as necessary. Make sure the cable is routed so it is not damaged by any moving parts of the vehicle.GPS Remote Mount AntennaThe external GPS antenna is an adhesive mount antenna.1. Locate a mounting position on highest point on the vehicle, following these precautions:• The antenna must be mounted so the antenna is not damaged while the vehicle or any of its parts are moving.2. Clean the area where the antenna is to be mounted.3. Remove the protective backing paper from the adhesive on the antenna and position the antenna on the vehicle.4. Attach the connector on the coaxial cable to the GPS antenna connector on the vehicle mounted Thor VM3.5. Use cable ties to secure the coaxial cable to the vehicle as necessary. Make sure the cable is routed so it is not damaged by any moving parts of the vehicle.Magnetic Mount WAN Antenna Adhesive Mount WAN AntennaThe Remote Antenna Installation Kit consists of the antenna and an integrated cable. The remote antenna is mounted on the top of a forklift, truck or other vehicle and cabled to the Thor VM3 inside the vehicle.To extension cableTo antennaTo antennaconnector oncomputerTo extension cableTo antennaTo antenna connector oncomputer

1 - 48Apply Touch Screen Protective FilmThe optional Thor VM3 touch screen protective film is shipped in packs of 10. The protective film is flexible and treated with an anti-glare coating on the outer surface.Installation1. Make sure the touch screen is clean and dry before installation. See Cleaning (page 1-16) for instructions on suitable cleaning agents.2. Pull the release tab to separate the protective backing from the rear of the protective film. Avoid touching the rear side of the protective film while removing the liner.3. Place the rear side of the protective film against the Thor VM3 display, roughly centering the protective film over the display.4. Slide the protective film until one corner can be slid back between the touch screen and the display housing as the protective film is re-centered on the display. It may be necessary to press the edges of the protective film against the display to ensure the entire edge slides under the display housing. It is easiest to start with one of the bottom corners.5. Slide the protective film away from the other bottom corner. The film may bulge sligthly away from the Reference Guide as it is being slid. Only slide the protective film enough so that the protective film can slide under the display housing on that corner when the protective film is returned to center. 6. Repeat with each of the top corners, sliding the protective film away from the corner just enough that the protective film can slide under the display housing when the protective film is returned to center.7. It may be necessary to flex the protective film during the install, however use care not to flex the protective film so much that the protective film kinks.8. Once all corners are secure under the display housing, adjust the protective film, if necessary, so it is centered on the touch screen.The protective film is slightly larger than the Thor VM3 touch screen, however the notches on the edge of the protective film (indicated by the arrows) correspond to the display size of the Thor VM3. The protective film is not adhesive. The corner edges are designed to fit between the Thor VM3 display and the display housing to hold the protective film in place.A protective backing is applied to the rear surface of the protective film. A pull tab is attached to the protective backing for easy removal of the pro-tective backing from the film.

$2 - 12SoftwareMicrosoft Windows Setup and ConfigurationAfter the system files are processed, Microsoft Windows begins to load. Windows maintains a System Registry and INI files. Standard Windows configuration options apply to the Thor VM3. Configuration options are located in the System Tray or the Control Panel:• The System Tray contains icons for adjusting the time, date or volume level.• The Control Panel contains icons for many other configuration options, such as Power Management, Regional and Language Options, etc.• The Control Panel icons are also used to add, delete or modify software installed on the Thor VM3.Drive C Folder StructureMicrosoft Windows is installed in the \Windows folder. In addition, Microsoft Windows creates other folders and several subfolders. For more information on the folder structure, please refer to commercially available Microsoft Windows OS ref-erence guides.Software Loaded on Drive CThe software loaded on the Thor VM3 computer consists of:•BIOS • Microsoft operating system (Windows Embedded Standard 2009)• device drivers• radio software, see Summit Client Utility (page 3-1)• touch screen software• keyboard wedge software, see Freefloat Link*One Wedge (page 2-2)The software installed on the Thor VM3 is summarized below.Note: Due to the complex folder structure and System Registry under Microsoft Windows, software should not be removed manually. Instead use the Windows Control Panel:Microsoft WindowsMicrosoft Windows is installed in the \Windows subfolder, which is the Windows default. In addition, Windows places files in other folders and subfolders during installation. For more information, please refer to commercially available Microsoft Windows OS user guides.Device DriversDevice drivers are installed for all installed hardware options, such as the display, touch screen, radios, etc. For more information on Microsoft Windows device drivers, please refer to commercially available Windows OS refer-ence guides.Radio SoftwareThe Thor VM3 is delivered with the radio software installed. Because the Thor VM3 uses a Microsoft Windows operating system, the radio installation includes Windows device drivers.Touch Screen SoftwarePenMount Universal software is installed for calibrating the touch screen. See Touch Screen Calibration (page 2-24) for more information.RFTermStart > All Programs > Honeywell RFTermOptional terminal emulation software. The application can also be accessed by double-clicking the RFTerm desk-top icon.Summit Client UtilityStart > Control Panel > Wi-FiManage wireless clients installed in the Thor VM3.$

$2 - 2Freefloat Link*One WedgeLink*One bar code decoder configuration software is installed on the Thor VM3. A pdf User’s Manual for Link*One is included as part of the installation at C:\Program Files\Freefloat\Freefloat Link One. Refer to this manual or the Freefloat website for information on configuring and using Link*One.Freefloat Access*One TE (Optional)Access*One terminal emulation software is available on the Thor VM3. A pdf User’s Manual for Access*One is included as part of the installation at C:\Program Files\Freefloat\Freefloat Access One. Refer to this manual or the Freefloat website for information on configuring and using Access*One.$

$2 - 3Control PanelMost control panel applets on the Thor VM3 are standard Microsoft Windows items. The control panels and other functions listed below may differ from a standard Microsoft Windows equipped PC or laptop.AboutSoftwareFirmware VersionsThe Software tab lists the firmware versions installed. The BIOS, EC and Screen MCU firmware versions are shown on this tab.LanguageThe Software tab displays the localized language version of the OS image. The language is identified as English or + an additional language.The Thor VM3 may be pre-loaded with an English only OS. Contact Technical Assistance (page 6-1) for informa-tion on ordering a recovery DVD with an additional language.Versions The Versions tab displays the versions of many of the software programs installed. Not all installed software is included in this list and the list varies depending on the applications loaded on the Thor VM3. The Image line displays the revision of the system software installed. Refer to the last three digits to determine the revision level.Versions Tab and the RegistryThe Versions tab displays program version details from the registry.Customized information can be displayed by modifying the Registry using the Registry Editor. Use caution when editing the Registry and make a backup copy of the registry before changes are made.The registry settings for the Version tab are under HKEY_LOCAL_MACHINE \ Software \ LXE \ Version in the reg-istry.To add a user application to the Version panel, create a new string value under the HKLM\Software\LXE\Version key. The string name should be the Application name to appear in the Version window. The data for the value should be the version number to appear in the Version window.Version strings can be equal to or less than 254 characters. Because the strings are displayed in a text box, any number can be accommodated, up to the 64K byte text box limitation.Network IP$

2 - 4MAC AddressThe Network IP tab displays the MAC address of the network card(s) such as the Summit WLAN radio and the Bluetooth module.

2 - 5BluetoothStart > Control Panel > Bluetooth Discover and manage pairing with nearby Bluetooth devices. Factory Default SettingsBluetooth taskbar Icon state and Bluetooth device Icon states change as Bluetooth devices are discovered, paired, con-nected and disconnected. There may be audible or visual signals as paired devices re-connect with the Thor VM3.• The default Bluetooth setting is On. • The Thor VM3 cannot be discovered by other Bluetooth devices when the Computer is discoverable option is disabled (unchecked) on the Settings panel. • Other Bluetooth devices cannot be discovered if they have been set up to be Non-Discoverable or Invisible.• When Filtered Mode is enabled, the Thor VM3 can pair with one Bluetooth scanner and one Bluetooth printer.• When Filtered Mode is disabled, the Thor VM3 can pair with up to four Bluetooth devices. • It is not necessary to disconnect a paired scanner and printer before a different scanner or printer is paired with the Thor VM3.• The target Bluetooth device should be as close as possible (up to 32.8 ft (10 meters) Line of Sight) to the Thor VM3 during the pairing process.Assumption: The System Administrator has Discovered and Paired targeted Bluetooth devices for the Thor VM3. The Thor VM3 operating system has been upgraded to the revision level required for Bluetooth client operation. An application (or API) is available that will accept data from serial Bluetooth devices.Discovered Devices NoneSettingsTurn off Bluetooth DisabledComputer is connectable EnabledComputer is discoverable DisabledPrompt if devices request to pair EnabledContinuous search DisabledFiltered Mode EnabledPrinted Port - COM7: Disabled (unchecked) by default in both Filtered and Non Filtered Modes. The option is dimmed in Non Filtered Mode.Logging DisabledComputer friendly name System Computer DescriptionReconnectReport when connection lost EnabledReport when reconnected DisabledReport failure to connect EnabledClear Pairing Table on Boot DisabledAuto Reconnect on Boot EnabledAuto Reconnect Enabled

2 - 6Bluetooth DevicesThe Bluetooth Devices tab displays any device previously discovered and paired with the Thor VM3. DiscoverTap the Discover button to locate all discoverable Bluetooth devices in the vicinity. The Discovery process also queries for the unique identifier of each device discovered. Stop ButtonTap Stop at any time to end the Discover and Query for Unique Identifier functions.Note: When an active paired device enters Suspend Mode, is turned Off or leaves the Thor VM3 Bluetooth scanning range, the Bluetooth connection between the paired device and the Thor VM3 is lost. There may be audible or visual signals as paired devices disconnect from the Thor VM3.

2 - 7Bluetooth Device ListThe discovered paired devices may or may not be identified with an icon. Discovered devices without an icon can be paired. The Bluetooth panel assigns an icon to the device name.An icon with a red background indicates the device's Bluetooth connection is inactive. An icon with a white background indicates the device is connected to the Thor VM3 and the device's Bluetooth connection is active.Double-tap a device in the list to open the device properties menu. The target device does not need to be active.Clear ButtonDeletes all devices from the Device table that are not currently paired. A dialog box is presented, “Delete all dis-connected devices?” Tap the Yes button to remove disconnected or deleted devices from the device table. The devices are removed from the Device table after closing and reopening the Bluetooth window. Tap the No button to make no changes.Bluetooth Device MenuPrerequisite: The Discover button has been clicked and there are Bluetooth devices listed.Click on a device in the list to highlight it. Double-click the highlighted device to display the Bluetooth Device right-click menu as shown below. The Bluetooth device does not need to be active.Right-Click Menu OptionsPair as Scanner Receive data from the highlighted Bluetooth scanner or Bluetooth imager.Pair as Printer Send data to the highlighted Bluetooth printer.Disconnect Stop the connection between the Thor VM3 and the highlighted paired Bluetooth de-vice.Delete Remove an unpaired device from the Bluetooth device list. The highlighted device name and identifier is removed from the Thor VM3 Bluetooth Devices panel after the user taps OK.Properties More information on the highlighted Bluetooth device.

2 - 8Bluetooth Device PropertiesData on the Bluetooth Properties panel cannot be changed by the user. The data displayed is the result of the device Query performed during the Discovery process.The Status dialog box reflects the current state of the highlighted device.SettingsNote: These options can still be checked or unchecked whether Bluetooth connection is enabled or disabled.Turn Off BluetoothTap the button to toggle the Bluetooth client On or Off. The button title changes from Turn Off Bluetooth to Tur n On Bluetooth.DefaultThe default value is Bluetooth On.OptionsOption InformationComputer is connectable This option is Enabled by default.Disable this option to inhibit Thor VM3 connection initiated by a Bluetooth scanner.Computer is discoverable This option is Disabled by default.Enable this option to ensure other devices can discover the Thor VM3.

$2 - 9Prompt if devices request to pair This option is Enabled by default.A dialog box appears on the Thor VM3 screen notifying the user a Bluetooth device requests to pair with the Thor VM3.The requesting Bluetooth device does not need to have been Discovered by the Thor VM3 before the pairing request is received.Tap the Accept button or the Decline button to remove the dialog box from the screen.In some cases, if a Bluetooth device is already paired this setting cannot be changed. If this is the case, an error message is displayed and the option is not changed. The Bluetooth device must be disconnected before changing this setting.Continuous Search This option is Disabled by default.When enabled, the Bluetooth connection never stops searching for a device it has paired with when the connection is broken (such as the paired device entering Sus-pend mode, going out of range or being turned off). When disabled, after being en-abled, the Thor VM3 stops searching after 30 minutes.Filtered Mode This option is Enabled by default.Determines whether the Bluetooth client discovers and displays all serial Bluetooth devices in the vicinity (Filtered Mode is disabled/unchecked) or the discovery result displays Bluetooth scanners and printers only (Filtered Mode is enabled/checked).When Filtered Mode is disabled, the Thor VM3 can pair with up to four Bluetooth de-vices.A Restart is required every time Filtered Mode is toggled on and off.When in non-filtered mode, the Thor VM3 supports SPP only.Printer Port - COM9 This option is Disabled by default.This option assigns Bluetooth printer connection to COM9 instead of COM19. To en-able this option, Filtered Mode must be enabled.Logging This option is Disabled by default.When logging is enabled, the Thor VM3 creates bt_log.txt and stores it in the C:/Pro-gram Files\LXE\Bluetooth folder. Bluetooth activity logging is added to the text file as activity progresses. A bt_log_bak.txt file contains the data stored by bt_log.txt prior to reboot.During a reboot process, the Thor VM3 renames bt_log.txt to bt_log_bak.txt. If a file already exists with that name, the existing file is deleted, the new bt_log_bak.txt file is added and a new bt_log.txt is created.Computer Friendly Name Default: Computer description (Control Panel > System > Computer Name tab).The name, or identifier, entered in this space by the System Administrator is used ex-clusively by Bluetooth devices and during Bluetooth communication.The Computer Description field is blank by default, so unless this field is modified be-fore Bluetooth is installed, Computer Friendly Name is also blank, but can be edited by the user.Option Information$