ICOM orporated 316700 VHF/UHF Amateur Transceiver User Manual ID 880H Draft

ICOM Incorporated VHF/UHF Amateur Transceiver ID 880H Draft

User Manual 3

Download: ICOM orporated 316700 VHF/UHF Amateur Transceiver User Manual ID 880H Draft
Mirror Download [FCC.gov]ICOM orporated 316700 VHF/UHF Amateur Transceiver User Manual ID 880H Draft
Document ID1074927
Application IDDd0QaZ9wdV6Xxp0N9/bhWg==
Document DescriptionUser Manual 3
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize126.65kB (1583137 bits)
Date Submitted2009-03-02 00:00:00
Date Available2009-03-02 00:00:00
Creation Date2009-02-23 09:38:17
Producing SoftwareAcrobat Distiller 8.1.0 (Windows)
Document Lastmod2009-02-23 09:38:41
Document TitleID-880H_Draft.pdf
Document CreatorAdobe InDesign CS2_J (4.0.5)
Document Author: i24589

MEMORY/CALL CHANNELS
N General description
The transceiver has 1050 memory channels, and 2 call channels. Memory channels include 50 scan edge memory channels (25 pairs) for storage of often-used frequencies.
And a total of 26 memory banks, A to Z, are available in each
band for storing groups of frequencies, etc. Up to 100 channels can be assigned into a bank.
D Memory channel contents
The following information can be programmed into memory
channels:
• Operating frequency (p. ??)
• Operating mode (p. ??)
• Duplex direction (+DUP or –DUP) with an offset frequency (p. ??)
• Subaudible tone encoder (p. ??), tone squelch or DTCS
squelch ON/OFF (p. ??)
• Subaudible tone frequency (p. ??), tone squelch frequency or DTCS code with polarity (pgs. ??, ??)
• Scan skip information (p. ??)
• Memory bank (p. ??)
• Memory name (p. ??)
• Tuning step (p. ??)
• Call sign squelch or Digital code squelch* (p. ??)
• Station call sign* (p. ??)
• RPT1/RPT2 call sign* (p. ??)
*Available for DV mode operation only.
NOTE:
Memory data can be erased by static electricity, electric
transients, etc.
In addition, they can be erased by malfunction and during
repairs.
Therefore, we recommend that memory data be written
down or be saved to a PC using the optional CS-80/880
CLONING SOFTWARE.
10
11
12
13
14
15
16
17
18
19
7
MEMORY/CALL CHANNELS
N Selecting a memory channel
D Using the tuning dial
D Using the keypad
q Push [M/CALL] several times to select memory mode.
• “X” indicator appears.
MR/CALL
w Rotate [DIAL] to select the desired memory channel.
• Programmed memory channels only can be selected.
Appears
[DIAL] [M/CALL]
D Using the [Y]/[Z] keys
z Push [MR/CALL] to select memory mode.
MR/CALL x Push [Y] or [Z] to select and set the desired
memory channel.
2/3
• Pushing and holding [Y]/[Z] for 1 sec. activates a
scan.
• If scan is activated, push [Y]/[Z] again or push
[CLR A(MW)] to stop it.
ENT
z Push [MR/CALL] to select memory mode.
x Push [ENT C(T-OFF)] to activate the keypad
for numeral input.
c Push 3 appropriate digit keys to input a channel number.
• Blank channel can be selected.
• Push only 1 appropriate digit key, [VOLY 0(TONE2)] to [SIMP 9(16-KEY-L)] then push [M(TONE-1)]
or [SQLZ #(16KEY-L)] to select scan edge channels. “M” and “#” can be used for “A” and “B” respectively.
MEMORY/CALL CHANNELS
N Selecting a call channel
Call channel is a pre-programmed memory channel that can
be accessed by simply pushing call channel button.
± Push [M/CALL] several times to select the call channel
mode, then rotate [DIAL] to select the desired call channel.
• “C0” or “C1” appears instead of memory channel number.
[DIAL]
[M/CALL]
MR/CALL
“C0” or “C1” appears
± Push and hold [MR/CALL] for 1 sec. to select
the call channel mode then push [Y]/[Z] to select the desired call channel in the main band.
• Push [MR/CALL] to select memory mode, or
push [VFO/LOCK] to select VFO mode.
10
11
12
13
14
15
16
17
18
19
7
MEMORY/CALL CHANNELS
N Memory channel programming
q Push [VFO/MHz] to select VFO mode.
w Set the desired frequency:
± Select the desired band with [BAND].
± Set the desired frequency with [DIAL].
± Set other data (e.g. offset frequency, duplex direction,
tone squelch, current call signs, etc.), if desired.
e Push [S.MW](MW) to enter select memory write mode.
• “X” indicator and the memory channel number blink.
r Rotate [DIAL] to select the desired channel.
• Call channels (C0, C1), VFO and scan edge channels (0A/0B
to 24A/24B), as well as regular memory channels, can be programmed in this way.
t Push and hold [MW](S.MW) for 1 sec. to program.
• 3 beeps sound.
• Memory channel number automatically increases when continuing to push [MW](S.MW) after programming.
FOR YOUR CONVENIENCE
Memory programming can be performed in various ways e.g.
memory channel to the same (or different) memory channel,
memory channel to the call channel, etc.
[EXAMPLE]: Programming 145.870 MHz into memory channel 20 (blank channel).
Rotate [DIAL] to select channel 20.
Push [S.MW].
[DIAL]
VFO mode
Enter select memory write mode.
Channel 20
Push and hold [MW] for 1 sec. to program
[S.MW/MW]
Return to the VFO mode.
CHAPTER CONTINUED
11
D Programming a memory channel via the microphone
The microphone can also be used to program memMW ory channels.
z Set the desired frequency in VFO mode.
± Push [VFO/LOCK] to select VFO mode.
± Push [ENT C(T-OFF)], then set the frequency using the
keypad.
± Set other data (e.g. offset frequency, duplex direction,
tone squelch, current call signs, etc.), if desired.
x Push [MR/CALL] to enter memory mode.
c Push [ENT C(T-OFF)], then set the desired memory channel using the keypad.
v Push [VFO/LOCK] to select VFO mode.
b Push [FUNC] then push and hold [CLR A(MW)] for 1 sec.
to program.
± 3 beeps may sound and the VFO contents (including the
subaudible tone frequency, etc.) are programmed.
± Memory channel number increases when continuing to
push [CLR A(MW)] after programming.
[EXAMPLE]: Programming 145.870 MHz into memory channel 20 (blank channel).
Push
Push
Push
Push
then
MR/
CALL
then
Push
for 1 sec. and continue to push
10
11
12
13
14
15
16
17
18
19
7
MEMORY/CALL CHANNELS
N Memory bank setting
The ID-880H has a total of 26 banks (A to Z). Regular memory
channels, 0 to 999, are assigned to the desired bank for easy
memory management.
t Rotate [DIAL] to select the bank group.
q Push [S.MW](MW) to enter select memory write mode.
• “X” indicator and the memory channel number blink.
w Rotate [DIAL] to select the desired memory channel.
e Push [  ](MONI) to select “BANK” setting.
r Push [  ](MONI) again.
• Bank group and channel number is displayed if the selected memory channel has already been previously assigned to a bank.
[DIAL]
y Push [](Low) to select the bank channel digit, then rotate
[DIAL] to select the bank channel number from “00” to “99.”
• Push [](CS) to return to the bank group selection, if desired.
[BAND]
Rotate [DIAL]
[BAND]
Push [BAND]
[S.MW/MW] [DIAL] [] []
[S.MW/MW] [DIAL]
Push [BAND]
u After editing, push [BAND] to select “BANK” setting.
i Push [MW](S.MW) for 1 sec. to assign the channel to the
bank.
• Return to the previous indication before entering select memory
write mode.
CHAPTER CONTINUED
N Memory bank selection
q Push [M/CALL] several times to select memory mode.
w Push [BAND] to enter the bank selection state.
e Rotate [DIAL] to select the desired memory bank group,
then push [BAND] again.
r Rotate [DIAL] to select the bank channel.
• Only programmed banks are displayed.
• Only programmed banks are displayed.
• Also regular memory channel can be selected.
[DIAL]
Push [BAND]
Regular memory channel
is displayed.
[DIAL] [M/CALL]
Bank channel is displayed.
Push [BAND]
Rotate [DIAL]
[BAND]
11
10
11
12
13
14
15
16
17
18
19
7
MEMORY/CALL CHANNELS
N Programming memory/bank/scan name
Each memory channel can be programmed with an alphanumeric channel name for easy recognition and can be indicated independently by channel. Memory and scan names
can be a maximum of 8 characters, and bank name can be a
maximum of 6 characters.
NOTE: Scan name indication can be turned ON or OFF in
DISP set mode (SET). (p. ??)
q Push [M/CALL] to select memory mode.
• To program a call channel name, push [M/CALL] to select call
channel mode.
w Rotate [DIAL] to select the desired memory channel.
i Repeat step u until the desired channel name is programmed.
o Push [  ](MONI).
t Push and hold [S.MW](MW) for 1 sec. to set the name
and exit channel name programming state.
• 3 beeps sound.
NOTE: Only one bank name can be programmed into
each bank. Therefore, the previously programmed bank
name will be displayed when bank name indication is selected. Also, the programmed bank name is assigned for
the other bank channels automatically.
• Select scan edge channels (0A/0B to 24A/24B) to program a scan
name.
e Push [S.MW](MW) to enter select memory write mode.
• “X” indicator and the memory channel number blink.
r Push [  ](MONI).
t Rotate [DIAL] to select “B NAME,” “M NAME” or “S NAME”
when programming the bank name, the memory name or
the scan name, respectively.
y Push [  ](MONI).
• A cursor blinks for the first character.
D Available characters
(A)
(B)
(C) (D)
(E)
(F)
(G) (H)
(I)
(J)
(K)
(L)
(M)
(N) (O) (P) (Q) (R)
(S)
(T)
(U)
(V) (W) (X)
(Y)
(Z)
(0)
(7)
(2)
(3)
(4)
(5)
(6)
(8)
(9)
(!)
(”)
(#)
($) (%) (&)
(’)
(()
())
() (+) (,)
(-)
(.)
(/)
(:)
(1)
u Rotate [DIAL] to select the desired character.
• The selected character blinks.
• Push [](LOW) to move the cursor right; push [](CS) to move
the cursor left.
• Push [CLR](DR) to erase the selected character, or push and hold
[CLR](DR) for 1 sec. to erase all characters followng the cursor.
(;)
( < ) ( = ) (>)
(?) ( @ ) (  )
(\)
(])
( ^ ) ( Space )
CHAPTER CONTINUED
N Selecting memory/bank
name indication
[EXAMPLE]:
Programming the memory name
“AIR” into the scan edge channel 3A.
[S.MW/MW] [DIAL]
During memory mode, rotate
[DIAL] to select 3A.
11
[ ][ ]
Rotate [DIAL] to enter “A,”
then [ ].
During memory mode operation, either the programmed
memory name or bank name can be displayed.
q Enter “NAME” in DISP menu.
MENU ¶ SET ¶ DISP ¶ NAME (p. ??)
(Push [MENU
Push [S.MW] to enter select
memory write mode.
Enter “I” and “R” with
[DIAL] and [ ].
Push [ ], then rotete [DIAL]
to select “M NAME.”
Push [ ], then push [MW]
for 1 sec. to program.
]), (Rotate [DIAL], then push [BAND].)
w Rotate [DIAL] to select the memory display type.
• OFF
: Displays the frequency.
• MEMORY : Displays the memory name.
• BANK
: Displays the bank name.
e Push [ ] (MONI) to DISP menu.
r Push [MENU
] to return to the previous indication before entering DISP menu.
NOTE: The programmed scan name is displayed during
the programmed scan selection.
[MENU
Push [ ].
Select “B NAME” or “S NAME”
when program-ming the bank
name or the scan name,
respectively.
[DIAL]
10
11
12
13
14
15
16
17
18
19
7
MEMORY/CALL CHANNELS
N Copying memory/call contents
This function copies a memory channel’s contents to VFO (or
another memory/call channel). This is useful when searching for
signals around a memory channel frequency and for recalling
the offset frequency, subaudible tone frequency etc.
D Memory/call¶VFO
q Select the memory (call) channel to be copied.
± Push [M/CALL] several times to select memory mode
or call channel mode, then rotate [DIAL] to select the
desired channel.
w Push and hold [MW](S.MW) for 2 sec. write the selected
channel contents to VFO mode.
MR/CALL
MW
2/3
• Returns to VFO mode automatically.
z Push [BAND] to select the desired band as
the main band, if necessary.
x Select the memory/call channel to be copied.
± Push [MR/CALL] to select memory mode,
then select the desired memory channel
via [Y]/[Z] or keypad.
± Push and hold [MR/CALL] for 1 sec. then
push [Y]/[Z] to select the call channel.
c Push [FUNC], then push and hold
[CLR A(MW)] for 1 sec. to copy the selected
memory/call channel contents to the VFO.
• VFO mode is selected automatically.
[EXAMPLE]: Copyinig memory channel 11 to VFO.
[DIAL]
[MW] [M/CALL]
Front panel operation:
Push [M/CALL] to select memory mode.
Rotate [DIAL] for selecting memory channel.
HM-133 operation:
MR/
Push CALL
to select memory mode.
Select memory channel.
Push
Push and hold [MW] for 2 sec.
then push and hold
for 1 sec.
CHAPTER CONTINUED
11
D Memory/call¶call/memory
q Select the memory (call) channel to be copied.
± Push [M/CALL] several times to select memory mode
or call channel mode, then rotate [DIAL] to select the
desired channel.
w Push [S.MW](MW) to enter select memory write mode.
• “X” indicator and the memory channel number blink.
• Do not hold [S.MW](MW) for more than 2 sec., otherwise the
memory contents will be copied to VFO.
e Rotate [DIAL] to select the target memory (call) channel.
• Scan edge channels, 0A/0B to 24A/24B can also be selected.
r Push and hold [MW](S.MW) for 1 sec. to write the selected
channel contents to the target channel.
• The targeted memory and copied contents are indicated.
[EXAMPLE]: Copyinig memory channel 11 contents to channel 15.
[DIAL]
[S.MW/MW]
Select a memory channel,
then push [S.MW].
Rotate [DIAL] to
select a target channel.
Push and hold [MW] for 2 sec.
10
11
12
13
14
15
16
17
18
19
7
MEMORY/CALL CHANNELS
N Memory clearing
Contents of programmed memories can be cleared (erased),
if desired.
q Push [S.MW](MW) to enter select memory write mode.
• “X” indicator and the memory channel number blink.
• Do not hold [S.MW](MW) for more than 2 sec. otherwise
the memory contents will be copied to VFO.
w Rotate [DIAL] to select the desired memory channel to be
cleared.
e Push and hold [CLR](DR) for 1 sec. to clear the contents.
• 3 beeps sound, then the frequency is cleared.
• “X” indicator and the memory channel number blink continu-
r Push [MENU
] to the previous indication before entering select memory write mode.
NOTE: Be careful!— the contents of cleared memories
CANNOT be recalled.
ously.
[EXAMPLE]: Clearing memory channel 14.
Push [S.MW] to enter select memory write mode.
[MENU
Rotate [DIAL] to select channel 14.
] [DIAL]
Push and hold [CLR] for 1 sec. to clear.
[S.MW]
[CLR]
Push [MENU
].
Channel 14
CALL CHANNEL OPERATION
N Erasing/transferring bank contents
The bank contents of programmed memory channels can be
cleared or reassigned to another memory bank.
e Push [BAND] to select “BANK” setting, then push [BAND]
again.
INFORMATION: Even if the memory bank contents are
cleared, the memory channel contents still remain
programmed.
q Select the desired bank contents to be transferred or
erased from the bank. (p. ??)
± Push [M/CALL] several times to select memory mode.
± Push [BAND], then rotate [DIAL] to select the desired
memory bank group, then push [BAND] again.
± Rotate [DIAL] to select the bank channel.
• Bank initial and bank channel stops blinking.
r Push [](Low) to select the bank channels selection, or
push [](CS) to select the bank group selection to be transferred.
t Rotate [DIAL] to select the desired bank group or channel.
• Select “– – – –” indication when erasing the contents from the
bank.
To transfer the bank contents
to channel 11 in Bank B.
[BAND]
[BAND]
Bank channel is displayed.
To erase.
[S.MW] [DIAL] [M/CALL]
w Push [S.MW](MW) to enter select memory write mode.
• Displays the original memory channel number automatically, and
then “X” indicator and the memory channel number blink.
• Do not hold [S.MW](MW) for more than 2 sec., otherwise the
memory contents will be copied to VFO.
[MW] [DIAL] [][]
“– – – –” is displayed.
y After editing, push [BAND] to select “BANK” setting.
u Push [MW](S.MW) for 1 sec. to erase/transfer the bank
contents.
10
11
12
13
14
15
16
17
18
19
MENU SCREEN OPERATION
10
N General
MENU screen is used for programming infrequently changed
values or conditions of functions.
e Rotate [DIAL] to select “SOUNDS,” then push [
(MONI).*
• Push [Ω](CS) to select the previous indication.
D Entering MENU screen and operation
e.g.) Set “KEY B (Key-touch beep)” to OFF.
q Push [MENU
] to enter MENU screen.
• One of “TS,” “DUP.T,” “SCAN,” “SET,” “DV SET,” “CALL-S,”
“RX CAL,” “MESSAG,” “RPT-L” or “GPS” appears.
w Rotate [DIAL] to select “SET,” then push [
r Rotate [DIAL] to select “KEY B ,” then push [
t Rotate [DIAL] to select “OFF,” then push [ ] (MONI).*
y Push [MENU
] to return to the indication before entering MENU screen.
*[
](MONI).*
] (MONI) ↔ [BAND MODE]/[≈](LOW)
• Push [Ω](CS) to select the previous indication.
• Example
[MENU
[DIAL]
Push [MENU
](MONI)
Rotate [DIAL]
Push [
Rotate [DIAL]
Push [
Rotate [DIAL]
Push [
Rotate [DIAL]
](MONI)
] (MONI).*
• Push [Ω](CS) to select the previous indication.
](MONI)
Push [
](MONI)
](MONI)
10
11
12
13
14
15
16
17
18
19
105
12
MENU SCREEN OPERATION
N MENU screen indication and arrangement
MENU screen shows one of the following indication.
• TS mode
• DV SET mode
Independent items
(see p. 000)
Setting (see p. 000)
• DUP.T mode
• CALL-S mode
Independent items
(see p. 000)
Independent items
(see p. 000)
• SCAN mode
• RX-CS mode
Independent items
(see p. 000)
• SET mode
Independent items
(see p. 000)
- FUNC mode
• MESSAG mode
Independent items
(see p. 000)
- DISP mode
Independent items
(see p. 000)
• RPT-L mode
Independent items
(see p. 000)
- SOUNDS mode
• GPS mode
Independent items
(see p. 000)
106
Independent items
(see p. 000)
Independent items
(see p. 000)
MENU SCREEN OPERATION
12
N Items list
D TS mode
D SET mode
See page 000 for details.
- FUNC mode
Item indication
D DUP.T mode
Item indication
Ref.
p. 000
Item indication
Ref.
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
Item indication
Ref.
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
D SCAN mode
Item indication
Ref.
p. 000
Ref.
p. 000
Item indication
Ref.
p. 000
p. 000
p. 000
p. 000
p. 000
- DISP mode
Item indication
Ref.
p. 000
Item indication
Ref.
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
- SOUNDS mode
Item indication
Ref.
p. 000
Item indication
Ref.
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
10
11
12
13
14
15
16
17
18
19
107
12
MENU SCREEN OPERATION
D RPT-L mode
D DV SET mode
Item indication
Ref.
p. 000
See p. 000 for details
p. 000
p. 000
D GPS mode
p. 000
p. 000
p. 000
p. 000
Ref.
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
p. 000
Ref.
p. 000
Item indication
p. 000
p. 000
p. 000
D CALL-S mode
Item indication
Ref.
p. 000
p. 000
D RX CAL mode
See p. 000 for details.
D MESSAG mode
See p. 000 for details.
108
Item indication
Item indication
Ref.
p. 000
p. 000
Item indication
Ref.
p. 000
MENU SCREEN OPERATION
12
N DUP.T mode items
D Offset frequency
D TSQL frequency
Sets the offset frequency for duplex (repeater) operation within
a 0 to 159.995 MHz range.
Selects tone frequency for tone squelch or pocket beep operation from one of 50 available frequencies (67.0–254.1 Hz).
(default: 88.5)
During 1 MHz step setting
± Push [VFO/MHz] each time to selecting the 10 MHz,
1 MHz step and the setting with the tuning step, selected
in VFO mode, in sequence.
• Available subaudible tone frequencies
• The default value may differ according to the selected frequency
band (before accessing DUP.T mode) and transceiver version.
The selected tuning step in VFO mode is used when setting the offset frequency.
D Repeater tone frequency
Selects subaudible tone frequency for accessing a repeater,
etc. 50 tone frequencies (67.0–254.1 Hz) are available.
(default: 88.5)
The transceiver has 50 tone frequencies and consequently
their spacing is narrow compared with units having 38
tones. Therefore, some tone frequencies may receive interference from adjacent tone frequencies.
10
11
12
13
14
15
16
17
18
19
109
12
MENU SCREEN OPERATION
D Digital code
DTCS code
Selects DTCS (both encoder/decoder) code for DTCS squelch
operation. Total of 104 codes (023–754) are available.
Sets the desired digital code for digital code squelch operation. Total of 100 codes (00–99) are available. (default: 00)
(default: 023)
• Available DTCS codes
DTCS polarity
Sets DTCS polarity from “BOTH N” (TX/RX: normal), “TN-RR”
(TX: normal, RX: reverse), “TR-RN” (TX: reverse, RX: normal) and
“BOTH R” (TX/RX: reverse).
(default: BOTH N)
Transmitting or receiving DTCS code’s polarity is sets by this
item at transmitting side and receiving side respectively.
110
D DTMF speed
Select the desired DTMF transmission speed from 100 msec,
200 msec, 300 msec, 500 msec.
• 100
: 100 msec. interval; 5.0 characters per second
(default)
• 200
: 200 msec. interval; 2.5 characters per second
• 300
: 300 msec. interval; 1.6 characters per second
• 500
: 500 msec. interval; 1.0 character per second
MENU SCREEN OPERATION
12
N Scan mode items
D Priority watch
D Scan resume timer
Activates priority watch or priority watch with alert (Bell).
• OFF
: The priority watch is turned OFF. (default)
• ON
: The transceiver checks the memory channel
frequency every 5 sec.
• BELL : The transceiver checks the memory channel
frequency every 5 sec. You can be alerted
with beeps and blinking “S.”
Selects the scan resume time from a pause after the received
signal disappears.
• 0SEC : Scan resumes when a received signal disappears.
• 1–5SEC : Scan pauses 1–5 sec. after a received signal
disappears. (default: 2 sec.)
• HOLD : Scan remains paused on the received signal
even if it disappears. Rotate [DIAL]† to resume
manually.
D Scan pause timer
Selects the scan pause time. When receiving signals, the
scan pauses according to the scan pause time.
• 2–20SEC : Scan pauses for 2–20 sec. on a received signal in 2 sec. steps. (default: 10 sec.)
• HOLD
: Scan pauses on a received signal until it disappears. Rotate [DIAL] to resume manually.
Scan resume timer must be set shorter than scan pause
timer (previous item), otherwise this timer does not activate.
D Program skip scan
Sets programmed skip scan setting from ON (default) and
OFF for full scan or programmed scan operation
10
11
12
13
14
15
16
17
18
19
111

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
XMP Toolkit                     : 3.1-702
Modify Date                     : 2009:02:23 09:38:41-05:00
Create Date                     : 2009:02:23 09:38:17-05:00
Metadata Date                   : 2009:02:23 09:38:41-05:00
Creator Tool                    : Adobe InDesign CS2_J (4.0.5)
Format                          : application/pdf
Title                           : ID-880H_Draft.pdf
Creator                         : i24589
Document ID                     : uuid:2e029786-f4c6-4e33-94b5-610a66581d32
Instance ID                     : uuid:ce618c08-5501-4e09-873a-62a35bc3da3a
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Has XFA                         : No
Page Count                      : 20
Author                          : i24589
EXIF Metadata provided by EXIF.tools
FCC ID Filing: AFJ316700

Navigation menu