ICOM orporated 316700 VHF/UHF Amateur Transceiver User Manual ID 880H Draft

ICOM Incorporated VHF/UHF Amateur Transceiver ID 880H Draft

User Manual 3

a12348910111213141516171819N General descriptionThe transceiver has 1050 memory channels, and 2 call chan-nels. Memory channels include 50 scan edge memory chan-nels (25 pairs) for storage of often-used frequencies.And a total of 26 memory banks, A to Z, are available in each band for storing groups of frequencies, etc. Up to 100 chan-nels can be assigned into a bank.D Memory channel contentsThe following information can be programmed into memory channels: • Operating frequency (p. ??)  • Operating mode (p. ??) •  Duplex direction (+DUP or –DUP) with an offset fre-quency (p. ??) •  Subaudible tone encoder (p. ??), tone squelch or DTCS squelch ON/OFF (p. ??) •  Subaudible tone frequency (p. ??), tone squelch fre-quency or DTCS code with polarity (pgs. ??, ??)  • Scan skip information (p. ??)  • Memory bank (p. ??)  • Memory name (p. ??)  • Tuning step (p. ??)  • Call sign squelch or Digital code squelch* (p. ??)  • Station call sign* (p. ??)  • RPT1/RPT2 call sign* (p. ??)*Available for DV mode operation only.7MEMORY/CALL CHANNELSNOTE:Memory data can be erased by static electricity, electric transients, etc.In addition, they can be erased by malfunction and during repairs.Therefore, we recommend that memory data be written down or be saved to a PC using the optional CS-80/880 CLONING SOFTWARE.765
bD Using the tuning dial q  Push [M/CALL] several times to select memory mode. • “X” indicator appears. w  Rotate [DIAL] to select the desired memory channel. •  Programmed memory channels only can be selected.D Using the [Y]/[Z] keysz  Push [MR/CALL] to select memory mode.x  Push [Y] or [Z] to select and set the desired memory channel. •  Pushing and holding [Y]/[Z] for 1 sec. activates a scan. •  If scan is activated, push [Y]/[Z] again or push [CLR A(MW)] to stop it.D Using the keypadz Push [MR/CALL] to select memory mode.x  Push [ENT C(T-OFF)] to activate the keypad for numeral input.c  Push 3 appropriate digit keys to input a chan-nel number.   • Blank channel can be selected. •  Push only 1 appropriate digit key, [VOLY 0(TONE-2)] to [SIMP 9(16-KEY-L)] then push [M(TONE-1)] or [SQLZ #(16KEY-L)] to select scan edge chan-nels. “M” and “#” can be used for “A” and “B” re-spectively.N Selecting a memory channel7MEMORY/CALL CHANNELS[DIAL]Appears[M/CALL]MR/CALL2/3MR/CALLENTC
c123456789101112131415161718197MEMORY/CALL CHANNELSN Selecting a call channelCall channel is a pre-programmed memory channel that can be accessed by simply pushing call channel button.±  Push [M/CALL] several times to select the call channel mode, then rotate [DIAL] to select the desired call channel.•  “C0” or “C1” appears instead of memory channel number.±  Push and hold [MR/CALL] for 1 sec. to select the call channel mode then push [Y]/[Z] to se-lect the desired call channel in the main band. •  Push  [MR/CALL] to select memory mode, or push [VFO/LOCK] to select VFO mode.“C0” or “C1” appears[DIAL][M/CALL]MR/CALL
d7MEMORY/CALL CHANNELSN Memory channel programmingq  Push [VFO/MHz] to select VFO mode. w  Set the desired frequency: ±  Select the desired band with [BAND].± Set the desired frequency with [DIAL].±  Set other data (e.g. offset frequency, duplex direction, tone squelch, current call signs, etc.), if desired.e  Push [S.MW](MW) to enter select memory write mode.• “X” indicator and the memory channel number blink.r  Rotate [DIAL] to select the desired channel.•  Call channels (C0, C1), VFO and scan edge channels (0A/0B to 24A/24B), as well as regular memory channels, can be pro-grammed in this way.t  Push and hold [MW](S.MW) for 1 sec. to program.• 3 beeps sound.•  Memory channel number automatically increases when continu-ing to push [MW](S.MW) after programming.FOR YOUR  CONVENIENCEMemory programming can be performed in various ways e.g. memory channel to the same (or different) memory channel, memory channel to the call channel, etc.Push and hold [MW] for 1 sec. to program[DIAL][S.MW/MW]Rotate [DIAL] to select channel 20.VFO mode Enter select memory write mode.Push [S.MW].Channel 20Return to the VFO mode.[EXAMPLE]: Programming 145.870 MHz into memory channel 20 (blank channel).
e11CHAPTER CONTINUED12345678910111213141516171819MWThe microphone can also be used to program mem-ory channels.z Set the desired frequency in VFO mode.± Push [VFO/LOCK] to select VFO mode.±  Push [ENT C(T-OFF)], then set the frequency using the keypad.±  Set other data (e.g. offset frequency, duplex direction, tone squelch, current call signs, etc.), if desired.x Push [MR/CALL] to enter memory mode.c  Push [ENT C(T-OFF)], then set the desired memory chan-nel using the keypad.v Push [VFO/LOCK] to select VFO mode.b  Push [FUNC] then push and hold [CLR A(MW)] for 1 sec. to program.±  3 beeps may sound and the VFO contents (including the subaudible tone frequency, etc.) are programmed.±  Memory channel number increases when continuing to push [CLR A(MW)] after programming.D  Programming a memory channel via the microphonePush            ,Push           then           for 1 sec. and continue to push MR/CALLPush           then Push           Push           [EXAMPLE]: Programming 145.870 MHz into memory channel 20 (blank channel).
f7MEMORY/CALL CHANNELSN Memory bank settingThe ID-880H has a total of 26 banks (A to Z). Regular memory channels, 0 to 999, are assigned to the desired bank for easy memory management.q  Push [S.MW](MW) to enter select memory write mode. • “X” indicator and the memory channel number blink.w  Rotate [DIAL] to select the desired memory channel.e  Push  [   ](MONI) to select “BANK” setting.r  Push  [   ](MONI) again. •  Bank group and channel number is displayed if the selected mem-ory channel has already been previously assigned to a bank.t  Rotate [DIAL] to select the bank group.y  Push [](Low) to select the bank channel digit, then rotate [DIAL] to select the bank channel number from “00” to “99.” •  Push [](CS) to return to the bank group selection, if desired.u  After editing, push [BAND] to select “BANK” setting.i  Push [MW](S.MW) for 1 sec. to assign the channel to the bank. •  Return to the previous indication before entering select memory write mode.[BAND][DIAL][S.MW/MW]Push [BAND]Push [BAND][DIAL][BAND][][]Rotate [DIAL][DIAL][S.MW/MW]
g11CHAPTER CONTINUED12345678910111213141516171819N Memory bank selectionq  Push [M/CALL] several times to select memory mode.w  Push [BAND] to enter the bank selection state.e  Rotate [DIAL] to select the desired memory bank group, then push [BAND] again. •  Only programmed banks are displayed. •  Also regular memory channel can be selected.r  Rotate [DIAL] to select the bank channel. •  Only programmed banks are displayed.Push [BAND]Push [BAND]Regular memory channelis displayed.Bank channel is displayed.[BAND][DIAL] [M/CALL]Rotate [DIAL][DIAL]
h7MEMORY/CALL CHANNELSN Programming memory/bank/scan nameEach memory channel can be programmed with an alpha-numeric channel name for easy recognition and can be in-dicated independently by channel. Memory and scan names can be a maximum of 8 characters, and bank name can be a maximum of 6 characters.NOTE: Scan name indication can be turned ON or OFF in DISP set mode (SET). (p. ??)q Push  [M/CALL] to select memory mode. •  To program a call channel name, push [M/CALL] to select call channel mode.w  Rotate [DIAL] to select the desired memory channel. •  Select scan edge channels (0A/0B to 24A/24B) to program a scan name.e  Push [S.MW](MW) to enter select memory write mode. • “X” indicator and the memory channel number blink.r  Push [   ](MONI). t  Rotate [DIAL] to select “B NAME,” “M NAME” or “S NAME” when programming the bank name, the memory name or the scan name, respectively.y  Push [   ](MONI).  •  A cursor blinks for the first character.u  Rotate [DIAL] to select the desired character.  • The selected character blinks. •  Push  [](LOW) to move the cursor right; push [](CS) to move the cursor left. •  Push [CLR](DR) to erase the selected character, or push and hold [CLR](DR) for 1 sec. to erase all characters followng the cursor.i   Repeat step u until the desired channel name is pro-grammed.o  Push [   ](MONI). t  Push and hold  [S.MW](MW) for 1 sec. to set the name and exit channel name programming state. •  3 beeps sound.NOTE: Only one bank name can be programmed into each bank. Therefore, the previously programmed bank name will be displayed when bank name indication is se-lected. Also, the programmed bank name is assigned for the other bank channels automatically.D Available characters(A) (B) (C) (D) (E) (F) (G) (H) ( I ) (J) (K) (L) (M)(N) (O) (P) (Q) (R) (S) (T) (U) (V) (W)(9) (!) (”)(0) (1) (2) (3) (4) (5) (6) (7) (8)(:)($) (%) (&) ( ’ )( ; )( < )( = ) (>) (?)( ( )(X) (Y) (Z)(#)( + )( / )( ) )(  )( , )( - )( . )( \ )( @ )(  )( ] )( ^ )( Space )
i11CHAPTER CONTINUED12345678910111213141516171819N  Selecting memory/bank name indicationDuring memory mode operation, either the programmed memory name or bank name can be displayed.q  Enter “NAME” in DISP menu.MENU ¶ SET ¶ DISP ¶ NAME (p. ??) (Push [MENU  ]), (Rotate [DIAL], then push [BAND].)w Rotate [DIAL] to select the memory display type.  • OFF  : Displays the frequency.  • MEMORY : Displays the memory name.  • BANK  : Displays the bank name.e Push [ ] (MONI) to DISP menu.r  Push [MENU  ] to return to the previous indication be-fore entering DISP menu.  NOTE: The programmed scan name is displayed during the programmed scan selection.[DIAL][S.MW/MW][EXAMPLE]: Programming the memory name“AIR” into the scan edge channel 3A.[   ][   ]Push [   ].During memory mode, rotate[DIAL] to select 3A.Push [S.MW] to enter selectmemory write mode.Rotate [DIAL] to enter “A,” then [   ].Enter “I” and “R” with[DIAL] and [   ].Push [   ], then rotete [DIAL]to select “M NAME.”Select “B NAME” or “S NAME” when program-ming the bank name or the scan name, respectively.Push [   ], then push [MW]for 1 sec. to program.[DIAL][MENU      ][    ]
j7MEMORY/CALL CHANNELSN Copying memory/call contentsThis function copies a memory channel’s contents to VFO (or another memory/call channel). This is useful when searching for signals around a memory channel frequency and for recalling the offset frequency, subaudible tone frequency etc.D Memory/call¶VFOq  Select the memory (call) channel to be copied. ±  Push [M/CALL] several times to select memory mode or call channel mode, then rotate [DIAL] to select the desired channel.w  Push and hold [MW](S.MW) for 2 sec. write the selected channel contents to VFO mode.  • Returns to VFO mode automatically.MR/CALLMW2/3z  Push [BAND] to select the desired band as the main band, if necessary.x  Select the memory/call channel to be copied. ±  Push [MR/CALL] to select memory mode, then select the desired memory channel via [Y]/[Z] or keypad. ±  Push and hold [MR/CALL] for 1 sec. then push [Y]/[Z] to select the call channel.c  Push [FUNC], then push and hold [CLR A(MW)] for 1 sec. to copy the selected memory/call channel contents to the VFO.  • VFO mode is selected automatically.Rotate [DIAL] for selecting memory channel.Push [M/CALL] to select memory mode.[EXAMPLE]: Copyinig memory channel 11 to VFO.Push and hold [MW] for 2 sec.Push           then push and hold           for 1 sec.MR/CALLPush           to select memory mode. Select memory channel.Front panel operation:HM-133 operation:[DIAL][M/CALL][MW]
k11CHAPTER CONTINUED12345678910111213141516171819D Memory/call¶call/memoryq  Select the memory (call) channel to be copied. ±  Push [M/CALL] several times to select memory mode or call channel mode, then rotate [DIAL] to select the desired channel.w  Push [S.MW](MW) to enter select memory write mode. • “X” indicator and the memory channel number blink. •  Do not hold [S.MW](MW) for more than 2 sec., otherwise the memory contents will be copied to VFO.e  Rotate [DIAL] to select the target memory (call) channel.  • Scan edge channels, 0A/0B to 24A/24B can also be selected.r  Push and hold [MW](S.MW) for 1 sec. to write the selected channel contents to the target channel. • The targeted memory and copied contents are indicated.Rotate [DIAL] toselect a target channel.Select a memory channel,then push [S.MW].[EXAMPLE]: Copyinig memory channel 11 contents to channel 15.Push and hold [MW] for 2 sec.[DIAL][S.MW/MW]
l7MEMORY/CALL CHANNELSN Memory clearing Contents of programmed memories can be cleared (erased), if desired.q  Push [S.MW](MW) to enter select memory write mode. • “X” indicator and the memory channel number blink. •  Do not hold [S.MW](MW) for more than 2 sec. otherwise the memory contents will be copied to VFO.w  Rotate [DIAL] to select the desired memory channel to be cleared.e Push and hold [CLR](DR) for 1 sec. to clear the contents.  • 3 beeps sound, then the frequency is cleared. •  “X” indicator and the memory channel number blink continu-ously.r  Push [MENU  ] to the previous indication before enter-ing select memory write mode.NOTE: Be careful!— the contents of cleared memories CANNOT be recalled.Push and hold [CLR] for 1 sec. to clear.[DIAL][S.MW] [CLR]Rotate [DIAL] to select channel 14.Push [S.MW] to enter select memory write mode.Channel 14Push [MENU      ].[EXAMPLE]: Clearing memory channel 14.[MENU      ]
m7CALL CHANNEL OPERATION12345678910111213141516171819The bank contents of programmed memory channels can be cleared or reassigned to another memory bank.  INFORMATION: Even if the memory bank contents are cleared, the memory channel contents still remain programmed.q  Select the desired bank contents to be transferred or erased from the bank. (p. ??) ±  Push [M/CALL] several times to select memory mode. ±  Push [BAND], then rotate [DIAL] to select the desired memory bank group, then push [BAND] again. ±  Rotate [DIAL] to select the bank channel.    • Bank initial and bank channel stops blinking.w  Push [S.MW](MW) to enter select memory write mode. •  Displays the original memory channel number automatically, and then “X” indicator and the memory channel number blink. •  Do not hold [S.MW](MW) for more than 2 sec., otherwise the memory contents will be copied to VFO. e  Push [BAND] to select “BANK” setting, then push [BAND] again.r  Push [](Low) to select the bank channels selection, or push [](CS) to select the bank group selection to be trans-ferred.t  Rotate [DIAL] to select the desired bank group or channel.  •  Select “– – – –” indication when erasing the contents from the bank.y  After editing, push [BAND] to select “BANK” setting.u  Push [MW](S.MW) for 1 sec. to erase/transfer the bank contents.N Erasing/transferring bank contents[BAND][DIAL] [M/CALL][S.MW][BAND][][][DIAL][MW]To transfer the bank contentsto channel 11 in Bank B.Bank channel is displayed.To erase.“– – – –” is displayed.
10510MENU SCREEN OPERATION12345678910111213141516171819N GeneralMENU screen is used for programming infrequently changed values or conditions of functions.D Entering MENU screen and operatione.g.) Set “KEY B (Key-touch beep)” to OFF.q Push [MENU  ] to enter MENU screen. •  One of “TS,” “DUP.T,” “SCAN,” “SET,” “DV SET,” “CALL-S,” “RX CAL,” “MESSAG,” “RPT-L” or “GPS” appears.w Rotate [DIAL] to select “SET,” then push [ ](MONI).*  • Push [Ω](CS) to select the previous indication.e  Rotate  [DIAL] to select “SOUNDS,” then push [ ] (MONI).*  • Push [Ω](CS) to select the previous indication.r Rotate [DIAL] to select “KEY B ,” then push [ ] (MONI).*  • Push [Ω](CS) to select the previous indication.t  Rotate [DIAL] to select “OFF,” then push [ ] (MONI).*y  Push [MENU  ] to return to the indication before enter-ing MENU screen. *[ ] (MONI) ↔ [BAND MODE]/[≈](LOW)[DIAL][MENU      ][    ](MONI)Push [MENU      ] Rotate [DIAL] Push [    ](MONI)Push [    ](MONI)Rotate [DIAL] Rotate [DIAL]Push [    ](MONI)Push [    ](MONI) Rotate [DIAL]• Example
10612 MENU SCREEN OPERATIONN  MENU screen indication and arrangementMENU screen shows one of the following indication.• TS mode • SCAN mode• SET mode Setting (see p. 000)Independent items(see p. 000)- FUNC mode - DISP mode - SOUNDS mode • DUP.T mode Independent items(see p. 000)• CALL-S mode Independent items(see p. 000)• RX-CS modeIndependent items(see p. 000)• MESSAG mode Independent items(see p. 000)• RPT-L modeIndependent items(see p. 000)• GPS mode Independent items(see p. 000)Independent items(see p. 000)• DV SET modeIndependent items(see p. 000)Independent items(see p. 000)Independent items(see p. 000)
10712MENU SCREEN OPERATION12345678910111213141516171819N Items listD TS modeSee page 000 for details.D DUP.T modeItem indication Ref. Item indication Ref.p. 000 p. 000p. 000 p. 000p. 000 p. 000p. 000D SCAN modeItem indication Ref. Item indication Ref.p. 000 p. 000p. 000 p. 000p. 000 p. 000D SET mode- FUNC modeItem indication Ref. Item indication Ref.p. 000 p. 000p. 000 p. 000p. 000 p. 000p. 000 p. 000p. 000 p. 000p. 000 p. 000p. 000 p. 000p. 000- DISP modeItem indication Ref. Item indication Ref.p. 000 p. 000p. 000 p. 000p. 000 p. 000p. 000- SOUNDS modeItem indication Ref. Item indication Ref.p. 000 p. 000p. 000 p. 000p. 000 p. 000p. 000
10812 MENU SCREEN OPERATIOND DV SET modeItem indication Ref. Item indication Ref.p. 000 p. 000p. 000 p. 000p. 000 p. 000p. 000 p. 000p. 000 p. 000p. 000 p. 000p. 000 p. 000p. 000D CALL-S modeItem indication Ref. Item indication Ref.p. 000 p. 000p. 000 p. 000D RX CAL modeSee p. 000 for details.D MESSAG modeSee p. 000 for details.D RPT-L modeSee p. 000 for detailsD GPS modeItem indication Ref. Item indication Ref.p. 000 p. 000p. 000 p. 000p. 000 p. 000p. 000 p. 000p. 000
10912MENU SCREEN OPERATION12345678910111213141516171819N DUP.T mode itemsD Offset frequency Sets the offset frequency for duplex (repeater) operation within a 0 to 159.995 MHz range.During 1 MHz step setting±  Push  [VFO/MHz] each time to selecting the 10 MHz, 1 MHz step and the setting with the tuning step, selected in VFO mode, in sequence. •  The default value may differ according to the selected frequency band (before accessing DUP.T mode) and transceiver version.  The selected tuning step in VFO mode is used when set-ting the offset frequency.D Repeater tone frequency Selects subaudible tone frequency for accessing a repeater, etc. 50 tone frequencies (67.0–254.1 Hz) are available.(default: 88.5)D TSQL frequency Selects tone frequency for tone squelch or pocket beep oper-ation from one of 50 available frequencies (67.0–254.1 Hz).(default: 88.5)• Available subaudible tone frequencies   The transceiver has 50 tone frequencies and consequently their spacing is narrow compared with units having 38 tones. Therefore, some tone frequencies may receive in-terference from adjacent tone frequencies.
11012 MENU SCREEN OPERATIOND DTCS code Selects DTCS (both encoder/decoder) code for DTCS squelch operation. Total of 104 codes (023–754) are available.(default: 023)• Available DTCS codesD DTCS polarity Sets DTCS polarity from “BOTH N” (TX/RX: normal), “TN-RR” (TX: normal, RX: reverse), “TR-RN” (TX: reverse, RX: normal) and “BOTH R” (TX/RX: reverse).  (default: BOTH N)Transmitting or receiving DTCS code’s polarity is sets by this item at transmitting side and receiving side respectively.D Digital code Sets the desired digital code for digital code squelch opera-tion. Total of 100 codes (00–99) are available.  (default: 00)D DTMF speed Select the desired DTMF transmission speed from 100 msec, 200 msec, 300 msec, 500 msec.• 100  :  100 msec. interval; 5.0 characters per second (default)• 200  : 200 msec. interval; 2.5 characters per second• 300  : 300 msec. interval; 1.6 characters per second• 500  : 500 msec. interval; 1.0 character per second
11112MENU SCREEN OPERATION12345678910111213141516171819N Scan mode itemsD Priority watch Activates priority watch or priority watch with alert (Bell).• OFF  : The priority watch is turned OFF. (default)• ON  :  The transceiver checks the memory channel frequency every 5 sec.• BELL  :  The transceiver checks the memory channel frequency every 5 sec. You can be alerted with beeps and blinking “S.”D Scan pause timer Selects the scan pause time. When receiving signals, the scan pauses according to the scan pause time.• 2–20SEC :  Scan pauses for 2–20 sec. on a received sig-nal  in 2 sec. steps. (default: 10 sec.)• HOLD    :  Scan pauses on a received signal until it dis-appears. Rotate [DIAL] to resume manually.D Scan resume timer Selects the scan resume time from a pause after the received signal disappears.• 0SEC  :  Scan resumes when a received signal disap-pears.• 1–5SEC :  Scan pauses 1–5 sec. after a received signal disappears. (default: 2 sec.)• HOLD  :  Scan remains paused on the received signal even if it disappears. Rotate [DIAL]† to resume manually.  Scan resume timer must be set shorter than scan pause timer (previous item), otherwise this timer does not activate.D Program skip scan Sets programmed skip scan setting from ON (default) and OFF for full scan or programmed scan operation

Navigation menu