ICOM orporated 333202 UHF Mobile Transceiver User Manual IC F5020 F6020 series Instruction Manual

Download:
Mirror Download [FCC.gov]
Document ID	1471491
Application ID	MQ4+3RJcCM0D8SwvkxBUzQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	123.87kB (1548432 bits)
Date Submitted	2011-05-24 00:00:00
Date Available	2011-07-31 00:00:00
Creation Date	2017-11-05 12:40:01
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-11-05 12:40:01
Document Title	IC-F5020_F6020 series Instruction Manual
Document Creator	Adobe InDesign CS3_J (5.0)
Document Author:	Icom Inc.

INSTRUCTION MANUAL
VHF MOBILE TRANSCEIVERS
iF5120D
Series
UHF MOBILE TRANSCEIVERS
iF6120D
Series
IMPORTANT
FCC INFORMATION
READ ALL INSTRUCTIONS
carefully and com-
pletely before using the transceiver.
SAVE THIS INSTRUCTION MANUAL — This
instruction manual contains important operating instructions for the IC-F5121D, IC-F5123D, IC-F5128D VHF MOBILE TRANSCEIVERS and the IC-F6121D, IC-F6123D, ICF6128D UHF MOBILE TRANSCEIVERS.
EXPLICIT DEFINITIONS
WORD
DEFINITION
R WARNING!
Personal injury, fire hazard or electric
shock may occur.
CAUTION
NOTE
Equipment damage may occur.
If disregarded, inconvenience only. No risk
of personal injury, fire or electric shock.
For Canada:
This device complies with RSS-310 of Industry Canada. Operation is subject to the condition that this device does not
cause harmful interference.
Cet appareil est conforme au CNR-310 d’Industrie Canada.
Son฀exploitation฀est฀autorisée฀sous฀réserve฀que฀l’appareil฀ne฀
cause฀pas฀de฀brouillage฀préjudiciable.
•฀FOR฀CLASS฀B฀UNINTENTIONAL฀RADIATORS:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
฀ •฀Reorient฀or฀relocate฀the฀receiving฀antenna.
฀ •฀฀Increase฀the฀separation฀between฀the฀equipment฀and฀receiver.
฀ •฀฀Connect฀the฀equipment฀into฀an฀outlet฀on฀a฀circuit฀different from that to which the receiver is connected.
฀ •฀฀Consult฀the฀dealer฀or฀an฀experienced฀radio/TV฀technician฀
for help.
CAUTION: Changes or modifications to this transceiver,
not฀expressly฀approved฀by฀Icom฀Inc.,฀could฀void฀your฀authority to operate this transceiver under FCC regulations.
PRECAUTIONS
R WARNING! NEVER connect the transceiver to an
AC outlet. This may pose a fire hazard or result in an electric
shock.
R WARNING! NEVER connect the transceiver to a
DO NOT use or place the transceiver in areas with temperatures below –30°C (–22°F) or above +60°C (+140°F), or
in areas subject to direct sunlight, such as the dashboard.
power source of more than 16 V DC or use reverse polarity.
This could cause a fire or damage the transceiver.
DO NOT operate the transceiver without running the vehicle’s engine. The vehicle’s battery will quickly run out when
the transceiver transmits while the vehicle’s engine is OFF.
R WARNING! NEVER cut the DC power cable be-
DO NOT฀place฀the฀transceiver฀in฀excessively฀dusty฀envi-
tween the DC plug and fuse holder. If an incorrect connection
is made after cutting, the transceiver might be damaged.
ronments.
R WARNING! NEVER place the transceiver where
DO NOT place the transceiver against walls. This will obstruct heat dissipation.
normal operation of the vehicle may be hindered or where it
could cause bodily injury.
DO NOT use harsh solvents such as benzine or alcohol
CAUTION: NEVER allow children to touch the trans-
when cleaning, as they will damage the transceiver surfaces.
ceiver.
CAUTION: NEVER฀ expose฀ the฀ transceiver฀ to฀ rain,฀
BE CAREFUL! The transceiver will become hot when
operating continuously for long periods of time.
snow or any liquids.
USE
the specified microphone only. Other microphones
have different pin assignments and may damage the transceiver.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom
Incorporated (Japan) in Japan, the United States, the United Kingdom,฀Germany,฀France,฀Spain,฀Russia฀and/or฀other฀countries.
All other products or brands are registered trademarks or trademarks
of their respective holders.
ii
TABLE OF CONTENTS
IMPORTANT .......................................................................... i
EXPLICIT DEFINITIONS ....................................................... i
FCC INFORMATION ............................................................. i
PRECAUTIONS .................................................................... ii
TABLE OF CONTENTS ....................................................... iii
iii
฀
฀
฀
PANEL DESCRIPTION................................................1–7
■ Front panel ...................................................................1
■ Function display ...........................................................2
■ Programmable function keys ........................................3
฀
฀
฀
฀
฀
฀
฀
฀
฀
฀
BASIC OPERATION ..................................................8–14
■ Turning ON the power ..................................................8
■ Channel selection .........................................................8
■ Call procedure ..............................................................9
■ Receiving and transmitting ...........................................9
■ User Set mode ...........................................................12
■ Encryption function.....................................................13
■ Emergency transmission ............................................13
■ Stun function ..............................................................14
■ Priority A channel selection ........................................14
■ Power OFF Emergency function ........................................ 14
฀
฀
฀
฀
฀
฀
฀
CONNECTION AND MAINTENANCE ....................15–17
■ Rear panel connection ...............................................15
■ Supplied Accessories .................................................16
■ Mounting the transceiver ............................................16
■ Antenna ......................................................................17
■ Fuse replacement ......................................................17
■ Cleaning .....................................................................17
■ Options .......................................................................17
4 SAFETY TRAINING INFORMATION .............................18
PANEL DESCRIPTION
■ Front panel
Function display (p. 2)
e Speaker
q AF VOLUME CONTROL KNOB [VOL]
Rotate the knob to adjust the audio output level.
฀
•฀Minimum฀audio฀level฀is฀pre-programmed.฀(p.฀12)
w UP/DOWN KEYS [CH Up]/[CH Down]
Push to select an operating channel, etc.
* The desired function can be assigned by your dealer. (p. 3)
e POWER KEY [ ]
฀ Push to turn the power ON or OFF.
฀
•฀The฀following฀optional฀functions฀are฀available฀at฀power฀ON:
- Automatic scan start
- Password prompt
r DEALER-PROGRAMMABLE KEYS
Required functions can be independently programmed by
your dealer. (p. 3)
t MICROPHONE CONNECTOR
Connect the supplied or optional microphone.
NEVER connect non-specified microphones. The pin assignments may be different and may damage the transceiver.
D Microphone
The supplied or optional microphone has a PTT switch and a
hanger hook.
•฀฀The฀following฀functions฀are฀available฀when฀the฀microphone฀is฀ON฀or฀
OFF hook (depending on the preprogramming):
- Automatic scan starts when you put it ON hook.
- Scan is cancelled when you take it OFF hook.
- Scan is paused when you take it OFF hook.
- Automatically selects the Priority channel when you take it OFF
hook.
- Sets to the ‘Inaudible’ mode (mute state) when you put it ON hook.
- Sets to the ‘Audible’ mode (unmute state) when you take it OFF
hook.
10
11
12
13
14
15
16
1
PANEL DESCRIPTION
■ Function display
q w
y u
y ENCRYPTION ICON
฀ A
฀ ppears when the encryption function is activated while
operating in the digital mode.
q TRANSMIT ICON
฀ Appears while transmitting a signal.
w BUSY ICON
฀ Appears while the channel is busy (receiving).
e SIGNAL STRENGTH ICON
฀ Shows the relative receive signal strength level.
Weak
Receive Signal level
Strong
r LOW POWER ICON
฀ Appears when low output power is selected.
t AUDIBLE ICON
฀ ➥ Appears when the channel is in the ‘Audible’ (unmute)
mode.
฀ ➥ Appears when a matching signal is received.
u BELL ICON
฀ ฀Appears/blinks฀when฀a฀matching฀2/5-tone฀or฀Digital฀ID*฀is฀
received, depending on the preprogramming.
i SCAN ICON
฀ ➥ Blinks during a scan.
฀ ➥ Appears when a scan channel is selected.
o ALPHANUMERIC DISPLAY
฀ Displays an operating channel number, channel name,
User Set mode contents, DTMF code, etc.
* Digital operation only
See the operating guide for details of MDC and Digital
system operations. Ask your dealer for details.
PANEL DESCRIPTION
■ Programmable function keys
The following functions can be assigned to [UP], [DOWN],
[P0], [P1], [P2] and [P3] programmable function keys.
Consult your Icom dealer or system operator for details concerning your transceivers programming.
CH UP AND DOWN KEYS
As described in the following topics, after pushing a programmed key, push [CH Up] or [CH Down] to select an option, setting, etc.
ZONE KEY
Push฀this฀key,฀then฀select฀the฀desired฀zone฀using฀[CH฀Up]/฀
[CH Down].
What is “zone”?— Certain channels are grouped together
and assigned to a zone, according to their intended to use.
For example,฀‘Staff฀A’฀and฀‘Staff฀B’฀are฀assigned฀to฀a฀“Business”฀zone,฀and฀‘John’฀and฀‘Cindy’฀are฀assigned฀to฀a฀“Private” zone.
SCAN START/STOPKEY
➥฀Push to start and cancel scanning operation.
฀
•฀฀When฀a฀scan฀is฀started฀with฀the฀Power฀ON฀Scan฀or฀Automatic฀
scan function, push this key to cancel it. The cancelled scan
resumes after the pre-programmed time period.
➥฀฀Hold down this key for 1 second to display the scan group,
then push [CH Up] or [CH Down] to select the desired
one.
SCAN ADD/DEL (TAG) KEY
➥฀ Push to add the channel to, or delete it from, the current
scan group.
฀
1. Push to display the scan group, then push [CH Up] or
[CH Down] to select the desired one.
2. Push to add the channel to, or delete it from, the selected scan
group.
3.฀Hold฀down฀for฀1฀second฀to฀exit฀the฀scan฀list฀selection฀mode.
➥฀ While a scan is paused on a non-priority channel, push this
key to delete the selected channel from the scan group.
Depending on the setting, the cleared channel is added
to the scan group again after the scan is cancelled.
10
11
12
13
14
15
16
1
PANEL DESCRIPTION
■ Programmable function keys (Continued)
PRIO A/B KEYS
➥ Push to select the Priority A or Priority B channel.
➥ Hold down [Prio A (Rewrite)] or [Prio B (Rewrite)] for
1 second to rewrite the operating channel as Priority A or
Priority B,
MR-CH 1/2/3/4 KEYS
Push to directly select memory channel 1 to 4.
MONI (AUDI) KEY
➥฀฀Push฀to฀turn฀the฀CTCSS฀(DTCS)฀or฀2/5-tone฀squelch฀mute฀
ON or OFF.
฀
฀
•฀฀Only฀during฀LMR฀(Land฀Mobile฀Radio)฀operation,฀push฀to฀open฀
any squelch, or deactivate any mute functions.
•฀฀Only฀during฀PMR฀(Private฀Mobile฀Radio)฀operation,฀push฀to฀activate one or two of the following functions on each channel (depending on the preprogramming):
- Hold down to unmute the channel (‘Audible’ mode).
- Push to mute the channel (‘Inaudible’ mode).
- After the communication is finished, push to send a ‘reset
code’ (only 5-tone operation).
NOTE: The ‘Audible’ (unmute) mode may automatically
return to the ‘Inaudible’ (mute) mode, after the pre-programmed time period.
LIGHT KEY
Push to turn ON the backlight for about 5 seconds, when the
backlight฀function฀is฀set฀to฀“OFF”฀in฀the฀User฀Set฀mode.
LOCK KEY
➥฀฀Hold฀down฀this฀key฀until฀“LOCK฀ON”฀is฀displayed฀to฀electronically฀lock฀all฀programmable฀keys฀except฀the฀following:
[Moni(Audi)], [Lock], [Call] (incl. Call A and Call B), [Emergency],
[Surveillance], [Siren], [Lone Worker] and [Light].
➥ When the Key Lock function is ON, hold down this key
until฀“LOCK฀OFF”฀is฀displayed฀to฀turn฀it฀OFF.฀
LONE WORKER KEY
Push to turn the Lone Worker function ON or OFF.
•฀฀If฀the฀Lone฀Worker฀function฀is฀turned฀ON,฀and฀no฀operation฀occurs฀
during the pre-programmed time period, the Emergency function is
automatically turned ON.
HIGH/LOW KEY
Push to select the transmit output power temporarily or permanently, depending on the preprogramming.
•฀Ask฀your฀dealer฀for฀the฀output฀power฀level฀for฀each฀selection.
C.TONE CH ENT KEY
Push to enter the continuous tone channel selection mode.
Then, push [CH Up] or [CH Down] to change the tone frequency/code฀setting.฀The฀selected฀channel฀remains฀set฀as฀
the continuous tone channel until another channel is designated as such.
PANEL DESCRIPTION
TONE/RAN CH SELECT KEY
➥ While in analog mode, push to enter the continuous tone
channel selection mode. Then push [CH Up] or [CH Down]
to฀select฀a฀desired฀tone฀frequency/code฀setting.฀After฀the฀
selection, push this key again to set it.
➥ While in digital mode, push to enter the RAN channel selection mode. Then push [CH Up] or [CH Down] to select a
desired RAN code. After the selection, push this key again
to set it.
➥฀฀While฀in฀mixed฀(digital฀and฀analog)฀mode,฀push฀to฀enter฀
the continuous tone channel selection mode. Then push
[CH฀Up]฀or฀[CH฀Down]฀to฀select฀a฀desired฀tone฀frequency/
code setting. After setting, push this key to set it. After
that, the RAN channel selection mode appears. Select a
desired RAN code with [CH Up] or [CH Down]. After the
selection, push this key again to set it.
TALK AROUND KEY
Push to turn the Talk Around function ON or OFF.
•฀฀The฀Talk฀Around฀function฀equalizes฀the฀transmit฀frequency฀to฀the฀
receive frequency for transceiver-to-transceiver communication.
WIDE/NARROW KEY
Push to toggle the IF bandwidth between wide and narrow.
•฀฀The฀wide฀passband฀width฀can฀be฀selected฀from฀25.0฀or฀20.0฀kHz฀
using฀the฀CS-F3100D/F5120D฀CLONING SOFTWARE. (PMR operation
only) Ask your dealer for details.
DTMF AUTODIAL KEY
➥ Push to enter the DTMF channel selection mode, then
push [CH Up] or [CH Down] to select the desired DTMF
channel.
➥ After selecting the DTMF channel, push again to transmit
the selected DTMF code.
RE-DIAL KEY
Push to transmit the last-transmitted DTMF code.
•฀TX฀memories฀are฀cleared฀after฀turning฀OFF฀the฀transceiver.
EMERGENCY KEY
Hold down for a specified period to transmit an emergency
call.
•฀฀If฀you฀want฀to฀cancel฀the฀emergency฀call,฀hold฀down฀the฀key฀again,฀
before transmitting it.
1
PANEL DESCRIPTION
■ Programmable function keys (Continued)
CALL KEYS
Push฀to฀transmit฀a฀2/5-tone฀ID฀code.
•฀฀Tone฀call฀transmission฀may฀be฀necessary฀before฀you฀call฀another฀
station, depending on your signalling system.
•฀฀[Call฀A]฀and/or฀[Call฀B]฀may฀be฀selectable฀when฀your฀system฀employs฀selective฀‘Individual/Group’฀calls.฀Ask฀your฀dealer฀which฀call฀
is assigned to each key.
SURVEILLANCE KEY
Push to turn the surveillance function ON or OFF.
When a signal is received, or a key is pushed, while this
function is turned ON, the beeps do not sound and the LCD
backlight does not light.
TX CODE CHANNEL SELECT KEY
➥ Push to enter the TX code channel selection mode, then
push [CH Up] or [CH Down] to set a desired channel.
(p. 10)
➥ While in the TX code channel selection mode, hold down
this key for 1 second to enter the TX code edit mode. Then
push [CH Up] or [CH Down] to set a desired digit. (p. 11)
TX CODE CHANNEL UP/DOWN KEYS
Push to select a TX code channel.
ID-MR SELECT KEY (PMR operation only)
➥ Push to recall the received ID code.
฀
SIREN
Hold down for 1 second to sound the siren.
This function can be used for situations other than an emergency฀alert,฀such฀as฀a฀security฀alarm฀for฀example.
•฀฀The฀ siren฀ can฀ only฀ be฀ stopped฀ by฀ turning฀ OFF฀ the฀ transceiver฀
power.
TX CODE ENTER KEY (PMR operation only)
Push to enter the TX code edit mode, then push [CH Up] or
[CH Down] to set a desired digit. (p. 11)
฀
•฀฀P ush฀ this฀ key,฀ then฀ select฀ the฀ ID฀ code฀ using฀ [CH฀ Up]/
[CH Down].
•฀Up฀to฀5฀codes฀can฀be฀memorized.
➥ Hold down this key for 1 second to clear the selected ID
code.
ENCRYPTION KEY
While operating in the digital mode, push to turn the encryption function ON or OFF.
PANEL DESCRIPTION
USER SET MODE KEY
➥ Hold down for 1 second to enter the User Set mode.
฀
•฀฀While฀in฀the฀User฀Set฀mode,฀push฀this฀key฀to฀select฀an฀item*,฀
and change the value or setting using [CH Up] or [CH Down].
*Selectable items may differ, depending on the preprogramming.
➥ Hold฀down฀this฀key฀for฀1฀second฀again฀to฀exit฀the฀User฀Set฀
mode.
The User Set mode is also available via the ‘Power ON’ function. In this case, all set mode items are available. See page
12.
HOOK SCAN
When the Hook Scan function is pre-programmed, push this
key to temporarily disable the function. Push this key again to
enable the function.
Ext. CH Sel Mode KEY
Push฀to฀turn฀the฀Ext.฀CH฀Select฀function฀ON฀or฀OFF.฀
When the function is turned ON, memory channels can be
selected฀with฀only฀and฀external฀input.฀
When the function is turned OFF, memory channels can be
selected by pushing [CH Up] or [CH Down], and cannot be
externally฀controlled.฀
•฀฀This฀function฀is฀available฀when฀the฀external฀unit,฀such฀as฀a฀dimmer฀
control is connected to the transceiver with an optional OPC-1939
or OPC-2078 cable (p. 17).
•฀Ask฀your฀dealer฀for฀more฀details฀on฀external฀input฀operation.
POWER OFF EMERGENCY
While holding down this key, turn OFF the transceiver to
activate the Power OFF Emergency function. This function
makes the transceiver transmit emergency calls, even though
it appears to be powered OFF. (p. 14)
10
11
12
13
14
15
16
2
BASIC OPERATION
■ Turning ON the power
■ Channel selection
q Push [ ] to turn ON the power.
w If the transceiver is programmed for a start up password,
input the digit codes as directed by your dealer.
There are several methods to select channels, and they may
differ, depending on your system set up.
฀
NON-ZONE TYPE:
To select the desired operating channel:
•฀Push฀[CH฀Up]฀or฀[CH฀Down].
•฀฀Push฀one฀of฀[MR-CH฀1]฀to฀[MR-CH฀4].
•฀The฀keys฀shown฀below฀can฀be฀used฀for฀password฀input:
The transceiver detects numbers in the same block as identical.
Therefore฀“01234”฀and฀“56789”฀are฀the฀same.
KEY
NUMBER
e฀฀If฀the฀“PASSWORD”฀indication฀does฀not฀clear฀after฀inputting 6 digits, the input code number may be incorrect. Turn
OFF the power and re-enter your password.
ZONE TYPE:
To select the desired operating channel:
Push [Zone], then push [CH Up] or [CH Down].
AUTOMATIC SCAN TYPE:
Channel setting is not necessary for this type. When turning
ON the power, the transceiver automatically starts scanning.
Scanning stops when a signal is detected.
BASIC OPERATION
■ Call procedure
■ Receiving and transmitting
When฀your฀system฀employs฀tone฀signaling฀(excluding฀CTCSS฀
and DTCS), a call procedure may be necessary prior to voice
transmission. The tone signalling employed may be a selective
calling system which allows you to call only specific station(s),
and prevents unwanted stations from contacting you.
Receiving:
q Hold down [ ] for 1 second to turn ON the power.
w Push [CH Up] or [CH Down] to select a channel.
e When receiving a call, rotate [VOL] to adjust the audio output level to a comfortable listening level.
q฀฀Select฀the฀desired฀TX฀code฀channel฀or฀2/5-tone฀code,฀according to your System Operator’s instructions.
NOTE: Depending on the preprogramming, the transceiver
automatically transmits the microphone audio for the specified
time period*, when a matched RX code signal is received.
฀
฀
•฀฀This฀ may฀ not฀ be฀ necessary,฀ depending฀ on฀ the฀ preprogramming.
•฀Refer฀to฀pages฀10฀and฀11฀for฀selection.
w Push [Call] (assigned to one of the dealer programmable
keys).
e After transmitting, the remainder of your communication
can be carried out in the normal fashion.
Selective calling
Non-selective calling
•฀HM-148G฀or฀HM-152฀HAND MICROPHONE is required.
* Depending on the preprogramming. Ask your dealer for details.
Transmitting:
Wait for the channel to become clear to avoid interference.
q Take the microphone OFF hook.
฀
฀
•฀฀The฀‘Audible’฀mode฀is฀selected.
•฀A฀priority฀channel฀may฀be฀automatically฀selected.
w Wait for the channel to become clear.
฀
•฀The channel is busy when the BUSY icon appears on the LCD.
e While holding down [PTT], speak into the microphone at
your normal voice level.
r Release [PTT] to return to receive.
฀IMPORTANT:฀To฀maximize฀the฀readability฀of฀your฀signal;
1. Pause briefly after pushing [PTT].
2. Hold the microphone 5 to 10 cm (2 to 4 inches) from
your mouth, then speak into the microphone at a normal
voice level.
10
11
12
13
14
15
16
2
BASIC OPERATION
■ Receiving and transmitting (Continued)
D Transmitting notes
•฀Transmit฀inhibit฀function
The transceiver has several inhibit functions which restrict
transmission under the following conditions:
฀ -฀฀The฀channel฀is฀in฀the฀‘Inaudible’฀(mute)฀mode;฀“ ” (Audible
icon) does not appear.
- The channel is busy. However, depending on the preprogrammed settings, you can transmit when the call includes
an unmatching (or matching) CTCSS (DTCS), RAN code,
or Individual or Talkgroup ID.
- The selected channel is a ‘receive only’ channel.
•฀Time-out฀timer
฀ ฀If฀ continuous฀ transmission฀ exceeds฀ the฀ pre-programmed฀
time-out timer limit, the transmission is cut off.
•฀Penalty฀timer
After the transmission is cut off by the time-out timer, transmission is further inhibited for the pre-programmed penalty
timer period.
•฀PTTID฀call
The transceiver automatically sends the 5-tone, DTMF, BIIS
or digital ANI ID code when [PTT] is pushed (at the beginning฀of฀the฀transmission),฀and/or฀when฀it฀is฀released฀(at฀the฀
end of transmission), depending on the preprogramming.
A PTTID call also be made with the MDC 1200 signaling
system.
10
D TX code channel selection
If the transceiver has a key assigned to [TX Code CH Select],
the dysplay can be toggled between the operating channel
number (or name) and TX code channel number (or name).
When the TX code channel number (or name) is displayed,
[CH Up] or [CH Down] selects the TX code channel.
USING [TX CODE CH SELECT] KEY:
q Push [TX Code CH Select]— a TX code channel number
(or name) appears.
w Push [CH Up] or [CH Down] to select the desired TX code
channel.
e After selecting, push [TX Code CH Select] to set.
฀
•฀Return฀to฀the฀stand-by฀mode.
r Push [Call] to transmit the selected TX code.
USING [TX CODE CH UP]/[TX CODE CH DOWN] KEY:
If the transceiver has a key assigned to [TX Code CH Up] or
[TX Code CH Down], the programmed TX code channel can
be directly selected when pushed.
BASIC OPERATION
D TX code number edit (PMR operation only)
If the transceiver has a key assigned to [TX Code CH Select]
or [TX Code Enter], TX code contents can be edited within
the allowable digits.
USING [TX CODE CH SELECT] KEY:
q Push [TX Code CH Select] to enter the TX code channel
selection mode.
฀
•฀฀Select฀the฀desired฀channel฀before฀entering฀the฀TX฀code฀channel฀
selection mode, if necessary.
w Hold down [TX Code CH Select] for 1 second to enter the
TX code edit mode.
฀
•฀The฀digit฀to฀be฀edited฀blinks.
e Push [TX Code CH Select] to select the desired digit to be
edited.
r Push [CH Up] or [CH Down] to select the desired digit.
t Push [TX Code CH Select] to set. The digit to the right will
automatically blink.
y Repeat r and t to edit all allowable digits.
u After editing, push [TX Code CH Select] to set.
฀
•฀Return฀to฀the฀stand-by฀mode.
i Push [Call] to transmit.
USING [TX CODE ENTER] KEY:
q Push [TX Code Enter] to enter the TX code edit mode.
฀
•฀The฀digit฀to฀be฀edited฀blinks.
w Push [TX Code Enter] to select the desired digit to be edited.
e Push [CH Up] or [CH Down] to select the desired digit.
r Push [TX Code Enter] to set. The digit to the right will automatically blink.
t Repeat e and r to edit all allowable digits.
y After editing, push [TX Code Enter] to set.
฀
•฀Return฀to฀the฀stand-by฀mode.
u Push [Call] to transmit.
D DTMF transmission
If the transceiver has a key assigned to [DTMF Autodial], the
automatic DTMF transmission function is available. Up to 8
DTMF channels are selectable.
q Push [DTMF Autodial]— a DTMF channel appears.
w Push [CH Up] or [CH Down] to select the desired DTMF
channel.
e Push [DTMF Autodial] to transmit the DTMF code.
10
11
12
13
14
15
16
11
2
BASIC OPERATION
■ User Set mode
The User Set mode can be accessed with the ‘Power ON’
function. In this case, all set mode items are selectable.
The User Set mode allows you to set seldom-changed settings,฀and฀you฀can฀“customize”฀the฀transceiver฀operation฀to฀
suit your preferences and operating style.
NOTE: While in the User Set mode, [Up], [Down] and [P0]
activate regardless of the assigned key functions.
Entering the User Set mode:
q Push [ ] to turn OFF the power.
w While holding down [P1] and [P2], push [ ] to turn ON the
power.
฀
•฀฀Hold฀down฀[P1]฀and฀[P2]฀continuously฀until฀“SET฀MODE”฀appears on the display.
[P1] [P2]
e Hold down [P0] for 1 second to enter the User Set mode.
฀
•฀฀To฀exit฀the฀User฀Set฀mode,฀hold฀down฀[P0]฀for฀1฀second฀again.
[P0]
12
r Push [P0] several times to select the appropriate item,
then push [Up] or [Down] to set the desired level or setting.
฀
•฀฀Selectable฀Set฀mode฀items฀are฀Backlight, Beep ON/OFF, Beep
Level, Ringer Level, SQL Level, AF Min Level, Mic Gain, Battery Voltage, Horn, Signal Moni, Lone Worker and System
Info.
[P0]
[Up]/[Down]
t Hold down [ ] for 1 second to turn OFF the power, then
ON again to return to the normal operating mode.
The User Set mode can also be selected using a programmable key. Please refer to the [User Set Mode] section on
page 6 for instructions on how to use the key assigned to the
User Set mode.
[User Set Mode] can be used for the quick item selection.
Set฀“Enable”฀for฀the฀often฀used฀items฀with฀the฀CS-F3100D/
F5120D CLONING SOFTWARE.
BASIC OPERATION
■ Emergency transmission
When [Emergency] is held down for the specified time period*, the emergency signal is transmitted on the specified
emergency channel once or repeatedly.
When no emergency channel is specified, the call is transmitted on the operating channel.
The repeat emergency signal is automatically transmitted
until you turn OFF the power.
Depending on the preprogramming, receiving a matching
5-tone code cancels the transmission.
If you want to cancel the Emergency function, hold down
[Emergency] for the pre-programmed time period again before transmitting the call.
If your transceiver is programmed for Silent operation, you
can transmit emergency calls without the beep sounding and
the LCD indication change.
฀฀IMPORTANT: It is recommended to set an emergency
channel individually to provide the certain emergency call
operation.
D NOTES
Depending on the preprogramming, the following functions
are automatically activated. Ask your dealer for details.
•฀Auto฀TX฀function
After the emergency call transmission, audio from the microphone is automatically transmitted for a specified time period.*
•฀The฀HM-148G฀or฀HM-152฀hand฀microphone฀is฀required.
•฀Auto฀RX฀function
After the emergency call transmission, the transceiver stands
by in the audible mode for the specified time period.*
* Depending on the preprogramming. Ask your dealer for details.
■ Encryption function
The encryption function provides private communication between stations while operating in the digital mode.
q Push [Encryption] to turn ON the encryption function.
฀
•฀“
” (Encryption icon) appears.
w Push [Encryption] again to turn OFF the encryption function.
฀
•฀“
” disappears.
13
2
BASIC OPERATION
■ Stun function
The฀dispatcher฀can฀send฀a฀2/5-tone฀signal฀that฀will฀stun,฀kill฀
or revive your transceiver.
When the Stun ID is received, a beep sounds*, and the transceiver becomes unusable. Receiving a Revive command or
entering password* (p. 8) is necessary to operate the transceiver again in this case.
When the Kill ID is received, a beep sounds*, and the transceiver becomes unusable (the transceiver switches to the
cloning required condition). Cloning the transceiver is necessary to operate the transceiver again in this case.
* Depending on the preprogramming. Ask your dealer for details.
See the operating guide for details of the Stun function
with the MDC and Digital system operations. Ask your
dealer for details.
■ Power OFF Emergency function
When the transceiver has a key assigned to Power OFF
Emergency, you can use the function.
This function makes the transceiver transmit emergency
calls, even though it appears to be powered OFF.
14
To activate the Power OFF Emergency function, turn the
power OFF while holding down [Power OFF Emergency].
When฀the฀function฀is฀activated,฀any฀key฀operation,฀the฀ON/
OFF Hook and Lone Worker functions become invalid. The
beep, display and speaker are turned OFF as well.
On the other hand, the transceiver can transmit emergency
calls according to the pre-programmed emergency settings.
Depending on the pre-programmed settings, the Remote
Monitor function can also be used (digital operation only).
To cancel the Power OFF Emergency function and restore
the transceiver, turn the power ON.
■ Priority A channel selection
When one of the following operations is performed, the transceiver automatically selects the Priority A channel.
•฀Turning฀ON฀the฀power
The Priority A channel is selected each time the transceiver
power is turned ON.
•฀Auto฀Reset
The Priority A channel is selected when the Auto Reset
timer ends.
•฀OFF฀hook
The Priority A channel is selected when you take the microphone OFF hook.
CONNECTION AND MAINTENANCE
■ Rear panel connection
Antenna
q ANTENNA CONNECTOR
Connect to an antenna. Ask your
dealer about antenna selection
and placement.
w EXTERNAL SPEAKER JACK
Connect to a 4 to 8 ø external speaker.
e MICROPHONE HANGER
Connect the supplied microphone hanger to the vehicle’s
ground for microphone on/off
hook functions. (See page 2)
Optional speaker
R WARNING! NEVER remove the
fuse-holders from the DC power cable.
(Depending on version, the fuse holder
may not be attached to the black cable.)
Red
Black
12V
Battery
NOTE: Use the terminals as shown
for the cable connections.
Crimp
Solder
r OPTIONAL CABLE (OPC-1939, OPC-2078)
Connect an external modem,
dimmer control, etc.
t DC POWER RECEPTACLE
Connect to a 12 V DC battery.
Pay attention to polarities.
10
11
12
13
14
15
16
R WARNING! NEVER connect
to a 24 V battery. This could
damage the transceiver.
15
3
CONNECTION AND MAINTENANCE
■ Supplied Accessories
Microphone
Microphone hanger
and screw set
Microphone
hanger cable
DC power cable
Function name
stickers*
Mounting bracket
■ Mounting the transceiver
The universal mounting bracket supplied with your transceiver allows overhead mounting.
•฀฀Mount฀the฀transceiver฀securely฀with฀the฀4฀supplied฀screws฀
to a thick surface which can support more than 1.5 kg
(3.3 lb).
Flat washer
Felt*
Spring washer
Flat washers
Nuts
Mounting screws
(5×12)
Spring washers
Bracket bolts
Self-tapping screws
(5×20)
* Used for labelling the programmable function
keys according to their assinged functions.
16
When using
self-tapping screws
*Felt reduces the effects of vibration.
CONNECTION AND MAINTENANCE
■ Antenna
■ Options
A key element in the performance of any communication systems is its antenna. Contact your dealer for more information
regarding antennas and how to install them.
•฀OPC-1132A/OPC-347฀DC POWER CABLE
Two fuse holders are attached. USE the 20 A fuse only.
OPC-1132A: 3 m (9.8 ft)
OPC-347: 7 m (23 ft)
■ Fuse replacement
•฀OPC-1939/OPC-2078฀ACC CABLE
฀ Allows฀you฀to฀connect฀to฀an฀external฀terminal.
OPC-1939: D-sub 15-pin, OPC-2078: D-sub 25-pin
A fuse is installed in each fuse holder of the supplied DC
power cable*. If a fuse blows or the transceiver stops functioning, track down the source of the problem if possible, repaire it and then replace the damaged fuse with a new rated
one.
*Depending on version, only one fuse holder may be attached.
❑฀Fuse฀rating:฀10฀A฀(for฀one฀fuse฀holder)/20฀A฀(for฀Two฀fuse฀holders)
USE the applicable fuse only.
•฀HM-152/HM-152T/HM-148G HAND MICROPHONE
HM-152 : Hand microphone
HM-152T : DTMF microphone
HM-148G : Self ground heavy duty microphone
•฀SM-26 DESKTOP MICROPHONE
•฀SP-22/SP-30 EXTERNAL SPEAKER
Input impedance : 4 ø
฀ SP-22฀ :฀Rated฀input;฀5฀W,฀Max.฀input;฀7฀W
฀ SP-30฀ :฀Rated฀input;฀20฀W,฀Max.฀input;฀30฀W
■ Cleaning
If the transceiver becomes dusty or dirty, wipe it clean with a
soft, dry cloth.
DO NOT use harsh solvents such as benzine or
alcohol, as they will damage the transceiver surfaces.
10
11
12
13
14
15
16
Approved Icom optional equipment is designed for optimal performance when used with an Icom transceiver.
Icom is not responsible for the destruction or damage to an Icom
transceiver in the event the Icom transceiver is used with equipment
that is not manufactured or approved by Icom.
17
4
W ARN ING
SAFETY TRAINING INFORMATION
Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed
for and classified as “Occupational Use Only”,
meaning it must be used only during the course of
employment by individuals aware of the hazards,
and the ways to minimize such hazards. This radio
is NOT intended for use by the “General Population” in an uncontrolled environment.
•฀฀For฀compliance฀with฀FCC฀and฀Industry฀Canada฀RF฀Exposure฀Requirements, the transmitter antenna installation shall comply with
the following two conditions:
฀ 1.฀The฀transmitter฀antenna฀gain฀shall฀not฀exceed฀0฀dBi.
2. IC-F5121D:
The antenna is required to be located outside of a vehicle and
kept at a distance of 45 centimeters or more between the transmitting antenna of this device and any persons during operation.
For small vehicle as worst case, the antenna shall be located on
the roof top at any place on the centre line along the vehicle in
order to achieve 45 centimeters separation distance. In order to
ensure this distance is met, the installation of the antenna must
be mounted at least 45 centimeters away from the nearest edge
of฀the฀vehicle฀in฀order฀to฀protect฀against฀exposure฀to฀bystanders.
2. IC-F6121D:
The antenna is required to be located outside of a vehicle and
kept at a distance of 37 centimeters or more between the transmitting antenna of this device and any persons during operation.
For small vehicle as worst case, the antenna shall be located on
the roof top at any place on the centre line along the vehicle in
order to achieve 37 centimeters separation distance. In order to
ensure this distance is met, the installation of the antenna must
be mounted at least 37 centimeters away from the nearest edge
of฀the฀vehicle฀in฀order฀to฀protect฀against฀exposure฀to฀bystanders.
18
3. IC-F5121D:
Transmit only when people outside the vehicle are at least the
recommended minimum distance of 100 centimeters away from
the properly installed antenna. This separation distance will ensure that there is sufficient distance from a properly installed
externally-mounted฀antenna฀to฀satisfy฀the฀RF฀exposure฀requirements฀in฀the฀applicable฀RF฀exposure฀compliance฀standards.
3. IC-F6121D:
Transmit only when people outside the vehicle are at least the
recommended minimum distance of 82 centimeters away from
the properly installed antenna. This separation distance will ensure that there is sufficient distance from a properly installed
externally-mounted฀antenna฀to฀satisfy฀the฀RF฀exposure฀requirements฀in฀the฀applicable฀RF฀exposure฀compliance฀standards.
SAFETY TRAINING INFORMATION
To ensure that your exposure to RF electromagnetic energy is within the FCC allowable limits for
occupational use, always adhere to the following
guidelines:
C AU TIO N
•฀฀DO NOT operate the radio without a proper antenna attached, as
this฀may฀damage฀the฀radio฀and฀may฀also฀cause฀you฀to฀exceed฀FCC฀
RF฀exposure฀limits.฀A฀proper฀antenna฀is฀the฀antenna฀supplied฀with฀
this radio by the manufacturer or an antenna specifically authorized
by the manufacturer for use with this radio.
•฀฀DO NOT฀transmit฀for฀more฀than฀50%฀of฀total฀radio฀use฀time฀(“50%฀
duty cycle”). Transmitting more than 50% of the time can cause
FCC฀RF฀exposure฀compliance฀requirements฀to฀be฀exceeded.฀The฀
radio฀is฀transmitting฀when฀the฀“transmit฀indicator”฀appears฀on฀the฀
LCD.฀You฀can฀cause฀the฀radio฀to฀transmit฀by฀pressing฀the฀“PTT”฀
switch.
Electromagnetic Interference/Compatibility
During transmissions, your Icom radio generates RF energy that
can possibly cause interference with other devices or systems. To
avoid such interference, turn OFF the radio in areas where signs are
posted to do so. DO NOT operate the transmitter in areas that are
sensitive to electromagnetic radiation such as hospitals, aircraft, and
blasting sites.
10
11
12
13
14
15
16
19
A-6903H-1EX-0a
Printed in Japan
© 2010–2011 Icom Inc.
Printed on recycled paper with soy ink.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
INFORMATION EN MATIÈRE DE SÉCURITÉ
Votre radio Icom produit une énergie
électromagnétique de radiofréquences
(RF), en mode de transmission. Cette
radio est conçue pour un «usage proA V E R T I S S E M E N T fessionnel seulement» et classée
comme tel, ce qui signifie qu’elle doit
être utilisée uniquement dans le cadre
d’un travail par des personnes
conscientes des dangers et des mesures visant à minimiser ces dangers.
Elle N’EST PAS conçue pour une «utilisation grand public», dans un environnement non contrôlé.
•฀฀Ain฀de฀satisfaire฀aux฀exigences฀de฀la฀FCC฀et฀d’Industrie฀
Canada฀en฀matière฀d’exposition฀aux฀RF,฀il฀est฀nécessaire฀que฀l’antenne฀soit฀installée฀conformément฀aux฀trois฀
conditions฀suivantes:
฀ 1.฀฀Le฀gain฀de฀l’antenne฀du฀radio฀émetteur฀ne฀doit฀pas฀
dépasser฀0dBi.
฀ 2.฀IC-F5121D:
฀ ฀ ฀Il฀faut฀que฀l’antenne฀émettrice฀de฀cet฀appareil฀soit฀placée฀à฀l’extérieur฀d’un฀véhicule฀et฀tenue฀éloignée฀d’au฀
moins฀45฀centimètres฀de฀toute฀personne฀pendant฀le฀
fonctionnement.฀Dans฀le฀pire฀des฀cas,฀pour฀un฀petit฀véhicule,฀l’antenne฀doit฀être฀placée฀sur฀le฀toit,฀n’importe฀
où฀dans฀l’axe฀central฀du฀véhicule,฀ain฀de฀respecter฀
une฀distance฀de฀45฀cm฀du฀bord฀le฀plus฀rapproché฀du฀
véhicule฀et฀ainsi฀éviter฀que฀les฀personnes฀présentes฀
soient฀exposées.
฀ 2.฀IC-F6121D:
฀ ฀ ฀Il฀faut฀que฀l’antenne฀émettrice฀de฀cet฀appareil฀soit฀placée฀à฀l’extérieur฀d’un฀véhicule฀et฀tenue฀éloignée฀d’au฀
moins฀37฀centimètres฀de฀toute฀personne฀pendant฀le฀
fonctionnement.฀Dans฀le฀pire฀des฀cas,฀pour฀un฀petit฀véhicule,฀l’antenne฀doit฀être฀placée฀sur฀le฀toit,฀n’importe฀
où฀dans฀l’axe฀central฀du฀véhicule,฀ain฀de฀respecter฀
une฀distance฀de฀37฀cm฀du฀bord฀le฀plus฀rapproché฀du฀
véhicule฀et฀ainsi฀éviter฀que฀les฀personnes฀présentes฀
soient฀exposées.
฀ 3.฀IC-F5121D:
฀ ฀ ฀Émettre฀uniquement฀lorsque฀les฀personnes฀à฀l’extérieur฀du฀véhicule฀se฀trouvent฀à฀au฀moins฀la฀distance฀
minimale฀recommandée฀de฀100฀cm฀de฀l’antenne฀correctement฀installée.฀Cette฀distance฀de฀sécurité฀assurera฀que฀les฀personnes฀soient฀placées฀sufisamment฀
loin฀ d’une฀ antenne฀ correctement฀ ixée฀ à฀ l’extérieur฀
pour฀satisfaire฀aux฀exigences฀en฀matière฀d’exposition฀
aux฀RF,฀en฀vertu฀des฀normes฀de฀conformité฀applicables.
฀ 3.฀IC-F6121D:
฀ ฀ ฀Émettre฀uniquement฀lorsque฀les฀personnes฀à฀l’extérieur฀du฀véhicule฀se฀trouvent฀à฀au฀moins฀la฀distance฀
minimale฀recommandée฀de฀82฀cm฀de฀l’antenne฀correctement฀installée.฀Cette฀distance฀de฀sécurité฀assurera฀
que฀les฀personnes฀soient฀placées฀sufisamment฀loin฀
d’une฀antenne฀correctement฀ixée฀à฀l’extérieur฀pour฀
satisfaire฀aux฀exigences฀en฀matière฀d’exposition฀aux฀
RF,฀en฀vertu฀des฀normes฀de฀conformité฀applicables.
Afin de vous assurer que votre exposition à une énergie électromagnétique
de RF se situe dans les limites permises par la FCC pour une utilisation
MISE EN GARDE
grand public, veuillez en tout temps
respecter les directives suivantes:
฀ •฀฀NE PAS฀faire฀fonctionner฀la฀radio฀sans฀qu’une฀antenne฀appropriée฀y฀soit฀ixée,฀car฀ceci฀risque฀d’endommager฀la฀radio฀et฀causer฀une฀exposition฀supérieure฀
aux฀limites฀établies฀par฀la฀FCC.฀L’antenne฀appropriée฀
est฀celle฀qui฀est฀fournie฀avec฀cette฀radio฀par฀le฀fabricant฀ou฀une฀antenne฀spécialement฀autorisée฀par฀le฀
fabricant฀pour฀être฀utilisée฀avec฀cette฀radio.
฀ •฀NE PAS฀émettre฀pendant฀plus฀de฀50฀%฀du฀temps฀total฀
d’utilisation฀de฀l’appareil฀(«50฀%฀du฀facteur฀d’utilisation»).฀Émettre฀pendant฀plus฀de฀50฀%฀du฀temps฀total฀
d’utilisation฀peut฀causer฀une฀exposition฀aux฀RF฀supérieure฀aux฀limites฀établies฀par฀la฀FCC.฀La฀radio฀est฀en฀
train฀d’émettre฀lorsque฀le฀témoin฀du฀mode฀de฀transmission฀s’afiche฀sur฀l’écran฀ACL.฀La฀radio฀émettra฀si฀
vous฀appuyez฀sur฀le฀bouton฀du฀microphone.
Interférence électromagnétique et compatibilité
En฀ mode฀ de฀ transmission,฀ votre฀ radio฀ Icom฀ produit฀ de฀
l’énergie฀de฀RF฀qui฀peut฀provoquer฀des฀interférences฀avec฀
d’autres฀appareils฀ou฀systèmes.฀Pour฀éviter฀de฀telles฀interférences,฀mettez฀la฀radio฀hors฀tension฀dans฀les฀secteurs฀
où฀ une฀ signalisation฀ l’exige.฀ NE PAS฀ faire฀ fonctionner฀
l’émetteur฀dans฀des฀secteurs฀sensibles฀au฀rayonnement฀
électromagnétique฀tels฀que฀les฀hôpitaux,฀les฀aéronefs฀et฀
les฀sites฀de฀dynamitage.
A-6903H-3EX
Imprimé฀au฀Japon
©฀2011฀Icom฀Inc.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : Icom Inc.
Create Date                     : 2011:03:04 15:24:14+09:00
Modify Date                     : 2011:05:19 13:48:20-04:00
Subject                         : VHF/UHF Mobile Transceivers
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Instance ID                     : uuid:761e248f-d854-4d95-bc42-c7b7543dea94
Document ID                     : adobe:docid:indd:4cee6761-4527-11e0-bd2b-eeeb2be71c0c
Rendition Class                 : proof:pdf
Derived From Instance ID        : 4cee6760-4527-11e0-bd2b-eeeb2be71c0c
Derived From Document ID        : adobe:docid:indd:a026ebc1-07f1-11e0-ae7a-dbd2cae4c0dc
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:4FAEBCA3FAF5DF118DC1C19B075DC92D, uuid:59DDCB9494F7DF1196F281EF6A8A2B2D, uuid:89C36CFE27C0DD118C77DB845B352397, uuid:87226C6EFBA2DC11BC919AE98B4C1726, uuid:A4EC39F4A8F3DF11A910A308F6DCA612, uuid:89C36CFE27C0DD118C77DB845B352397, uuid:19713C578EDADF11941DD5E74C7F6A42, uuid:05F851C989BFDD119DCAE5983C171B7A, uuid:89C36CFE27C0DD118C77DB845B352397, uuid:89C36CFE27C0DD118C77DB845B352397, uuid:89C36CFE27C0DD118C77DB845B352397, uuid:99D4257C3DC0DD11A733D8DE64A3FCC2, uuid:84C36CFE27C0DD118C77DB845B352397, uuid:06F851C989BFDD119DCAE5983C171B7A, uuid:89C36CFE27C0DD118C77DB845B352397, uuid:9AD4257C3DC0DD11A733D8DE64A3FCC2, uuid:58DDCB9494F7DF1196F281EF6A8A2B2D, uuid:E7F7F669E9FCDF11A19BEC36C56837F3, uuid:DE35C500EFF5DF11A961D309096909A3, uuid:F168476FD7CCDD11A5B8CED1E62EDBB0, uuid:F368476FD7CCDD11A5B8CED1E62EDBB0
Manifest Reference Document ID  : uuid:4EAEBCA3FAF5DF118DC1C19B075DC92D, uuid:1309B2F7F9A2DC11BC919AE98B4C1726, uuid:88226C6EFBA2DC11BC919AE98B4C1726, uuid:86226C6EFBA2DC11BC919AE98B4C1726, uuid:76DBE0A19ECCDD11A5B8CED1E62EDBB0, uuid:88226C6EFBA2DC11BC919AE98B4C1726, uuid:8A226C6EFBA2DC11BC919AE98B4C1726, uuid:8C226C6EFBA2DC11BC919AE98B4C1726, uuid:88226C6EFBA2DC11BC919AE98B4C1726, uuid:88226C6EFBA2DC11BC919AE98B4C1726, uuid:88226C6EFBA2DC11BC919AE98B4C1726, uuid:8E226C6EFBA2DC11BC919AE98B4C1726, uuid:0957AB6FB0A3DC11AE44EBC3F4988633, uuid:90226C6EFBA2DC11BC919AE98B4C1726, uuid:88226C6EFBA2DC11BC919AE98B4C1726, uuid:479EFEBDFBA2DC11BC919AE98B4C1726, uuid:DC35C500EFF5DF11A961D309096909A3, uuid:E6F7F669E9FCDF11A19BEC36C56837F3, uuid:3D1A5F1112EBDC11AD63EA5C5D28C457, uuid:F068476FD7CCDD11A5B8CED1E62EDBB0, uuid:F268476FD7CCDD11A5B8CED1E62EDBB0
Metadata Date                   : 2011:05:19 13:48:20-04:00
Creator Tool                    : Adobe InDesign CS3_J (5.0)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 7441 bytes, use -b option to extract)
Format                          : application/pdf
Title                           : IC-F5020_F6020 series Instruction Manual
Creator                         : Icom Inc.
Description                     : VHF/UHF Mobile Transceivers
Light Source                    : Unknown
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Mode                       : UseOutlines
Page Count                      : 25

EXIF Metadata provided by EXIF.tools