ICOM orporated 400900 Wireless 802.11 abgn/ac indoor AP User Manual AP 95M Precaution ENG 1 indd

Download:
Mirror Download [FCC.gov]
Document ID	4116990
Application ID	10mV0vNqIBJ/9TakD2esnA==
Document Description	Users Manual (Statement)_rev.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.17kB (227120 bits)
Date Submitted	2018-12-26 00:00:00
Date Available	2018-12-27 00:00:00
Creation Date	2018-12-17 09:29:14
Producing Software	Acrobat Distiller 19.0 (Windows)
Document Lastmod	2018-12-17 09:29:14
Document Title	AP-95M_Precaution_ENG_1.indd
Document Creator	PScript5.dll Version 5.2.2
Document Author:	i32972

RESETTING THE AP-95M
PRECAUTIONS
If you cannot access the AP-95M setting screen, you can reset the AP-95M.
• This resets all settings to the factory defaults.
• If you can access the setting screen, see the AP-95M instruction manual (PDF) to reset from the setting screen.
Thank you for purchasing this Icom product. The AP95M
is designed and built
with Icom’s IP network technology. It complies with the
“IEEE802.11ac Wave 2” standard, and is designed for
dual band communications in the 5 GHz and 2.4 GHz
bands.
WIRELESS ACCESS POINT
AP-95M
IEEE802.11ac Wave 2 standard
Hold down the [MODE] button.
IMPORTANT
DC Jack
EXPLICIT DEFINITIONS
READ ALL INSTRUCTIONS carefully and completely
WORD
DEFINITION
Personal injury, fire hazard or electric
RWARNING! shock may occur.
Equipment damage may occur.
CAUTION
If disregarded, inconvenience only. No risk
NOTE
of personal injury, fire or electric shock.
before using the AP-95M.
SAVE THESE INSTRUCTIONS — These instructions
contain important safety and operating instructions for the
AP-95M.
Plug in the power
Bottom view
Indicators
PRECAUTIONS
Disconnect all cables from the AP-95M, and then
connect the power adapter.
DC Jack
• Confirm that the [POWER] indicator is lit in green.
• The other indicators status may differ, depending on the
operation status.
Indications

: OFF
: Lights
:Blinks
Power ON
Lights (green)
Hold down [MODE] with a pin on the top panel until all
indicators light green.
Hold down
Lights (green)
[MODE] button
Confirm that all indicators are lit in green, and then
release [MODE].
Release
Blinks (green)
• When the initialization has been completed, the [POWER]
indicator lights green.
R WARNING! NEVER use other than the specified
power adapter. This may result in an electrical shock, cause
a fire or damage the AP-95M.
R WARNING! Immediately disconnect the power adapter
if the AP-95M emits an abnormal odor, sound or smoke.
Contact your Icom dealer or distributor for advice.
R WARNING! NEVER use non-specified accessories.
R WARNING! NEVER put the AP-95M in any unstable
This may result in an electrical shock, cause a fire or
damage the AP-95M.
place (such as on a slanted surface or vibrating place). This
may cause injury and/or damage to the AP-95M.
R WARNING! NEVER attempt to connect the power
CAUTION: NEVER install the AP-95M in a place without
air vents. Heat dissipation may be reduced, and this could
damage the AP-95M.
adapter to other than the [DC] jack on the AP-95M bottom
panel. This may result in an electrical shock, cause a fire or
damage the AP-95M.
Lights (green)
■ For the AP-95M
[MODE] Button
Lights (green)
R WARNING! NEVER disassemble, modify or repair the
CAUTION: DO NOT use the AP-95M near a television or
radio. This could cause harmful interferences.
R WARNING! NEVER install the AP-95M in a wet place
CAUTION: DO NOT use or place the AP-95M in areas
with temperatures below –10ç (+14ƒ) or above +55ç
(+131ƒ).
AP-95M. This may result in an electrical shock, cause a fire
or damage the AP-95M.
or outside. This may result in an electrical shock, cause a
fire or damage the AP-95M.
CAUTION: DO NOT place the AP-95M in direct sunlight.
This could damage the AP-95M.
R WARNING! NEVER operate or touch the AP-95M with
CAUTION: DO NOT use the AP-95M in strong magnetic
fields or in an area with high static electricity. This could
damage the AP-95M.
wet hands. This may result in an electrical shock or damage
the AP-95M.
R WARNING! NEVER connect the ground terminal to a
CAUTION: Disconnect the power adapter when you will
not use the AP-95M for a long period of time.
gas or electric pipe. This may result in an electrical shock or
cause a fire.
CAUTION: DO NOT use harsh solvents such as benzine
R WARNING! NEVER use the AP-95M during a thunder
or alcohol to clean the AP-95M, as they can damage the
AP-95M’s surfaces. If the AP-95M becomes dusty or dirty,
wipe it clean with a dry, soft cloth.
and lightning storm. Using it may result in an electrical
shock, cause a fire or damage the AP-95M. Always
disconnect the power adapter before a storm.
Always place the AP-95M in a secure place to avoid
inadvertent contact with children.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the
United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand, and/or other countries.
All other products or brands are registered trademarks or trademarks of their respective holders.
–4–
–1–
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Dec. 2018
A7493W-1EX-1
Printed in Japan
© 2018 Icom Inc.
PRECAUTIONS (Continued)
WIRELESS LAN INFORMATION
■ For the power adapter
■ Other precautions
■ Precautions on using the wireless LAN
■ Wireless LAN installation location
R WARNING! NEVER use the power adapter with any
device other than the AP-95M. This may result in an
electrical shock, cause a fire or damage the power adapter.
• For information about operating the PC or external
devices, refer to their instruction manuals for details.
For the Canadian version
• Operation of this device in the 5150 ~ 5250 MHz
frequency range is restricted to indoor operation only.
Have the following installation conditions under
consideration so that the communication range and
speed are not affected.
• Outdoor operation in the 5150 ~ 5250 MHz frequency
range is prohibited.
• Data communication errors may occur if the wireless LAN
terminal and this device are too close to each other. Keep
them at least 1 meter (3.3 ft) away from each other.
• The optional power adapter may at some time need to
be replaced, depending on its life expectancy. The life of
a power adapter differs according to the environment or
condition in which the adapter is used.
R WARNING! NEVER connect the adapter into an outlet that
is not between 100 V and 240 V AC. Otherwise, this may result
in an electrical shock, cause a fire or damage the power adapter.
R WARNING! NEVER install the power adapter to wet
place outside or near a humidifier. This may result in an
electrical shock, cause a fire or damage the power adapter.
We recommend replacement when it has been used for
approximately 5 years (When used under the ambient
temperature of 25°C: 77°F). Contact your local dealer for
details.
R WARNING! NEVER put something heavy on the power
adapter cable. This may result in an electrical shock, cause
a fire or damage the power adapter.
RF Exposure Warning
This equipment must be installed and operated in
accordance with provided instructions and the antenna(s)
used for this transmitter must be installed to provide a
separation distance of at least 23 cm from all persons and
must not be co-located or operated in conjunction with
any other antenna or transmitter. End-users and installers
must be provided with antenna installation instructions and
transmitter operating conditions for satisfying RF exposure
compliance.
R WARNING! NEVER modify, bend by force, twist, pull
or heat the power adapter’s cable. This may result in an
electrical shock, cause a fire or damage the power adapter.
R WARNING! NEVER touch the power adapter with wet
hands. This may result in an electrical shock or damage the
power adapter.
R WARNING! NEVER use or place the power adapter and
connection cable where they could be inadvertently used by
children. This may result in an electrical shock or cause injury.
FOR CANADA
FCC INFORMATION
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Canada, Industry Canada (IC) Notices
This device complies with ISED’s licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference, including interference
that may cause undesired operation.
Changes or modifications to this device, not expressly approved
by Icom Inc., could void your authority to operate this device under
FCC regulations.
• Install the device in as open a place as possible indoors.
• This product has the frequency range approved only
for indoor use. Follow the restrictions of the laws and
regulations of each country.
• Install the device in a stable place where there is no
danger of falling or vibration.
• Do not place anything on top of this device.
• We recommend that users with pacemakers take
precautions to be sure that this device does not cause
them a problem because of electromagnetic interferences.
• The communication range expands in an open space.
However, in such location as warehouses with metallic
walls, the walls may cause the radio waves to reflect.
Radio waves may pass through a wall or window, but not
through metal.
Some concrete walls are metal reinforcing structures, and
may intercept the communication.
Heat absorbing glass or IR reflecting glass may intercept
the communication.
• Do not use this device near microwave ovens.
A microwave oven may cause electromagnetic
interference to the communications through this device.
• Do not modify the device. The device warranty does not
cover any problems caused by unauthorized modification.
■ Communicating with the 40/80 MHz
bandwidth
• Communication may not be able to be performed with a
wireless LAN installed on a different floor.
• When you are using the 40 MHz or 80 MHz bandwidth
mode on the wireless LAN, first check the radio wave environment around in order to not to interfere other radio stations.
SAFETY TRAINING INFORMATION
• In case you have harmfully interfered a radio station using
this device, set the “Bandwidth” to “20 MHz (default).”
➥ Refer to the instruction manual on the Icom website
about the bandwidth details.
This device was tested and approved with original
accessories to ensure FCC Compliance. The use of thirdparty accessories may not comply with FCC RF exposure
compliance requirements, and should be avoided.
(i) the device for operation in the band 5150 ~ 5250 MHz
is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems.
FOR CLASS B UNINTENTIONAL RADIATORS:
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
(ii) where applicable, antenna type(s), antenna models(s),
and worst-case tilt angle(s) necessary to remain
compliant with the e.i.r.p. elevation mask requirement
set forth in section 6.2.2.3 shall be clearly indicated.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below
the Industry Canada (IC) radio frequency exposure limits.
The Wireless Device should be used in such a manner such
that the potential for human contact during normal operation
is minimized.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device has also been evaluated and shown compliant
with the IC RF Exposure limits under mobile exposure
conditions. (Antennas must maintain a separation distance
of more than 26 cm from a person’s body)
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 23 cm between the radiator &
your body.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with greater
than 26 cm between the radiator & your body.
FCC Caution:
Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to
operate this equipment.
This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
For all versions
–2–
–3–

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : i32972
Create Date                     : 2018:12:17 09:29:14+09:00
Modify Date                     : 2018:12:17 09:29:14+09:00
XMP Toolkit                     : Adobe XMP Core 5.6-c016 91.163616, 2018/10/29-16:58:49
Format                          : application/pdf
Title                           : AP-95M_Precaution_ENG_1.indd
Creator                         : i32972
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 19.0 (Windows)
Document ID                     : uuid:adbae6df-7939-4dc0-b86a-7e12650cdfda
Instance ID                     : uuid:21227cb8-6f9d-4806-9044-57d46e91c620
Page Count                      : 2

EXIF Metadata provided by EXIF.tools