Koden Electronics RB719A Marine Radar RA55 User Manual C18 CHAP7 T Shooting 1
Koden Electronics Co., Ltd Marine Radar RA55 C18 CHAP7 T Shooting 1
Contents
C18
CHAPTER 7. TROUBLESHOOTING The first step to take when your radar is not operating properly is to reboot the software. Press and hold the POWER key for three seconds to turn the unit off. Wait for 15 seconds, then power on again. If this does not correct the difficulty, then try a master reset. With the unit turned off, press and hold the FTC and RANGE UP buttons, then press POWER. When the screen lights up, release two buttons. If the problem persists at this point, continue with the troubleshooting steps. WARNING There are high voltage circuits inside of this radar. Do not attempt to open the rear cover of display unit or disassemble internal parts. When you open the radome for installation, power must be off. Even if power switch is OFF, this radar is still supplied with power inside. 7.1 Fault Diagnosis by Self-check ___________________________ This radar has a self-check to diagnose equipment faults. If the unit is operable so that you can access the MENU function, select SETUP>SYSTEM CHECK and press "ENT". Refer to section 5.5.4.5 - Fault Diagnosis by Self Check (SYSTEM CHECK). 7.2 Troubleshooting System Components Tab. 7-1 Troubleshooting Symptom (1) Radar cannot be powered on. (2) Nothing is displayed although radar is powered on. (3) Screen is dark. (4) Radar images do not appear although screen display is present. (5) Echo image on screen differs from actual image. (6) Echo images are blurred. Cause The unit is not receiving power Power supply voltage is off specified value. Fuse in power cable is blown. Brightness is improperly adjusted. LCD is faulty. Brightness is improperly adjusted. Backlight is faulty. Scanner interconnecting cable connector is not seated properly Cable connectors inside radome are not seated properly Boat heading is incorrectly set. Timing adjustment is incorrectly set. GAIN, STC, or FTC is improperly set. Magnetron has degraded. RA51/52/53/54/55 INSTRUCTION MANUAL – 05 Corrective action Use a voltmeter to check for power where the cable is connected to your boat's power source. Correct voltage to within specified power range. (See Section 3.2) Replace fuse. (See Chapter 6) Use BRIL key to adjust. (See Section 5.3.) Contact your dealer. Use BRIL key to adjust. (See Section 5.3. Contact your dealer. Go to system check menu to determine missing signals. Make sure display set to radar mode (not monitor mode) Unplug and reattach cable connectors inside scanner Set boat heading correctly. (See Section 5.5.4.6.5) Set timing adjustment correctly. (See Section 5.5.4.6.5) Adjust. (See Section 5.3.6 to 5.3.8.) Contact your dealer. 69 (7) Too noise. much Radar is not tuned correctly Radar is not properly grounded. (8) No response when a key is pressed. Panel key is not contacting. Power supply circuit is faulty. (9) No NMEA data present 70 Incorrect data being transmitted by talker device. Adjust TUNE. (See Section 5.5.3.4) Connect grounding wire to boat's bonding or grounding system. (See Section 3.4 to 3.6.) Use SYSTEM CHECK to confirm. (See Section 5.5.4.5) Contact your dealer. Contact your dealer. With radar powered off, press and hold MOB and RANGE UP keys, then press POWER. When screen lights up, release two buttons. Unit will display actual NMEA data being transmitted. Correct talker as necessary. RA51/52/53/54/55 INSTRUCTION MANUAL – 05
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 2 Creator : C18_CHAP7_T Shooting-1.rtf - Microsoft Word Create Date : 2002:08:30 17:23:22 Title : C18_CHAP7_T Shooting-1.PDF Author : 109983 Producer : Acrobat PDFWriter 4.0 Windows NTEXIF Metadata provided by EXIF.tools