Kondo Kagaku T125003 Remote Control Transmitter User Manual manual 52 78

Kondo Kagaku Co., Ltd. Remote Control Transmitter manual 52 78

Contents

manual 52 78

Usage of the transmitter Features Main Menu Connecting the receiver Notes on installing Description Index52Back KeyEnter KeyJogDial+/- KeyResetFunction Menu AUTO STARTReturn at Back key, But ready are still existing.Reset then start blinking "READY"Set Throttle position.Set trigger position to start functionPull the trigger to turn on the TH:POS functionWhen back the trigger display OFF.When came back during on and off light, it is still effectiveadvicePlease check the movement before use.PRESET : Position of throttle when function the AUTO STARTInitial Value F 0 Max F150 Min F 0TH:POS : Position to start AUTO STARTInitial Value 5% Max 100% Min 5% or OFFPush Enter or Back key to return to Menu list.Push enter key to change the cursor. to editable each item.Setup value can reset by push reset key.When reset at first screen. AUTO START function will be waiting modeUse Jog dial or + ,- keys to move at setup screen(Can not move to setup screen While blinking the "READY")Use "Jog dial" key or "+,-" keys. to choose the "AUTO:START" from Menu list.From initial screen. use "Jog dial" key or "+,-" keys. to open Function menu.[How to open the set-up screen.]DRAFT
Usage of the transmitter Features Main Menu Connecting the receiver Notes on installing Description Index53Back KeyEnter KeyJogDial+/- KeyResetFunction MenuMODEL.COPYCopy the data in Model memory to other Model memory.ex. To Copy Data of MODEL MEMORY1 to MODEL MEMORY2A copy place is chosen."No" is selected and press enter key , return to menu list screen. Press "Enter Key" or "Back Key,return to Menu list screen."Yes" is selected and press "Back Key",cursol Model copy is finished and blink "COMPLETE" in LCD panel.Overwritten data aren't restored. Please confirm it before execution well.It is useful When used in the following situation.Save the Current data and then try the New setup.Move the data from Data PackCan swap the other data to the memoryCan copy the Data. but the setup data can not copy to the unitPush "ENTER" key or "BACK" key to Return to Menu list, If Model Copy was done and "COMPLETE" displayed at screenUse "Jog dial" key or "+,-" keys. then push "Enter" keyWhen Select YES then push "ENTER" key: Do MODEL COPY then display "COMPLETE"When Select NO then push "ENTER" key: Back to Menu listWhen Select YES then push "BACK" key: Cursor will mmove to NOWhen Select NO then push "BACK" key: Beep soundPush "Enter" key. to enter setup menu. use "Jog dial" key or "+,-" keys. to Select Model Memory number.Use "Jog dial" key or "+,-" keys. to choose the "MODEL.COPY" from Menu list.From initial screen. use "Jog dial" key or "+,-" keys. to open Function menu.[How to open the set-up screen.]Save the current Model memory to other Model memory.Can select setup that match to the condition of trackIt will better to be copied to other memory before changing setting.DRAFT
Usage of the transmitter Features Main Menu Connecting the receiver Notes on installing Description Index54Back KeyEnter KeyJogDial+/- KeyResetFunction MenuPut name at Model memoryMODEL.NAME(Model Name)An usable letter:The letter which can input till 10 characters.Push enter after select.Push "Enter" key. to enter setup menu. use "Jog dial" key or "+,-" keys. to adjust the value.Use "Jog dial" key or "+,-" keys. to choose the "MODEL.NAME" from Menu list.From initial screen. use "Jog dial" key or "+,-" keys. to open Function menu.Put the name for Identified model memory[How to open the set-up screen.])Can use at initial screen and model select that model name. When enter or edit the name. use Jog dial or +, - key to move the cursor to edit or enter the characters.DRAFT
Usage of the transmitter Features Main Menu Connecting the receiver Notes on installing Description Index55Back KeyEnter KeyJogDial+/- KeyResetFunction MenuFormat to factory setting the model memory. MEM.RESET(Memory reset)Erased data aren't restored. Please confirm it before execution well.adviceUse data pack to save the setup.Only model memory in use is erased.Setting of a main menu isn't deleted.Back to menu list When push back key."Yes" is selected and press "Enter Key",delete model memory.Push "Enter" key. to enter setup menu. use "Jog dial" key or "+,-" keys. to choose Yes/No.Use "Jog dial" key or "+,-" keys. to choose the "MEM.REST" from Menu list.From initial screen. use "Jog dial" key or "+,-" keys. to open Function menu.Model memory will Back to factory setting.Format all data of model memory.[How to open the set-up screen.]DRAFT
Usage of the transmitter Features Main Menu Connecting the receiver Notes on installing Description Index56Back KeyEnter KeyJogDial+/- KeyResetFunction MenuUpdate information in a system of the VR that consumed.ADJUST VR(Adjust variable resister)Do ADJUST VRDoneProcedure of Setup ADJUST VRControl SteeringControl SteeringFull Turn to leftCancel Cancel CancelFull Turn to RightWhen display "COMPLETE" Push "ENTER" key or "BACK" key to Done.Control TriggerControl TriggerPull the Trigger to full fowardThrottlePush the Trigger to full back.This number are sample. This value can not use.Trigger can be canceled with back key after operation till "Enter" is pushed.(Not Over-write the memory)Beep sound does it, in the case of a steering or trigger operation data abnormality or no operation and a key isn’t function.adviceCause of trouble When use this function imperfectly.Recommend to send to our service department for repair, when you are not familiar with this function.When push "ENTER". not to touch Steering wheel or throttle trigger during execution of "ADJUST VR".This Function for Cancellation of inconvenience of Consumption of the volume.It is depend on your Use frequency and An operation method.When Even this function can not fix the problems, please send to our service department to repair.Push Back key to return to Menu list. Select No: Return to Menu listSelect Yes: Do Adjust VR.From initial screen. use "Jog dial" key or "+,-" keys. to open Function menu.Use "Jog dial" key or "+,-" keys. to choose the "ADJUST VR" from Menu list.Move to yes/no to control "Jog dial" key or "+,-" keys.[How to open setup screen]DRAFT
Usage of the transmitter Features Main Menu Connecting the receiver Notes on installing Description Index57Back KeyEnter KeyJogDial+/- KeyResetFunction MenuNormal ResponseThis mode can use all type of servo and receiver.Super High Speed ResponseThis mode is adopted in MARS-R. Old receiver and Servo can't be used at this mode. but the response are improved.Advanced High Speed ResponseThis mode can show the original speed. Digital servo is required for this mode.CH.SELECT(Channel Select)advicePlease see page 19 about details of response mode.Push Enter to Move between Item to ItemPush Back to return to menu.Use Jog dial to control CH3Select FunctionEND ENDWhen setting of 3CH are in "FIX":Signal in itself is fired, but can't control a signal because it was fixedWhen assign to BT or ET. can function as switch movement.or can assign reverse switch to change movement directionsAdvanced High Speed ResponseSuper High Speed ResponseHigh ResponseNormal ResponseAbout Response mode: This unit can select from 3 kind of response modeThe movement of channel 3 is adjust max and min of rudder angle (switch-movement)Push Back key to return to menu list.To control Jog dial to select 2or 3 channel.When select 3 channel. the "setup" will display at lower part of screen. then can select the control function for 3rd channelAt menu list, Move the cursor to the CH.SELECT. use "Jog dial" or "+, -" key. then push Enter.From initial screen, open the function menu. use "Jog dial" or "+, -" key.Select 2 Channel or 3 channel.Also select the switch at back of moduleWhen the switch are in High response mode 2channel : Advanced High Speed Response 3channel : Super High Speed Response[How to open the set-up screen.]DRAFT
Usage of the transmitter Features Main Menu Connecting the receiver Notes on installing Description Index58Back KeyEnter KeyJogDial+/- KeyResetFunction MenuSet the direction of movement of each channel.Can Set the direction of movement of each channel.Use this function when the turing direction of servo is opposite to the wheel/trigger operation.REVERSE (Reverse Switch)Can change selected ChannelPush Enter or Back key to return the cursor.In an Electric car an ESC will adjust Throttle. When reverse isn't set up, it's not work normally at old ESC.A movement direction of steering are depend on each cars. Check the setup after mount to the car.Push back key to back to menu list.Push "Enter" key. to enter setup menu. use "Jog dial" key or "+,-" keys. to adjust the value.The menu for 3ch will display, when selected the CH.SELECT. (page 57)Use "Jog dial" key or "+,-" keys. to choose the "REVERSE" from Menu list.From initial screen. use "Jog dial" key or "+,-" keys. to open Function menu.[How to open the set-up screen.]DRAFT
Usage of the transmitter Features Main Menu Connecting the receiver Notes on installing Description Index59Back KeyEnter KeyJogDial+/- KeyResetFunction MenuAdjust Movement volume of the one step of Trim.Total step of Trim are 100, adjust Movement volume of the one step of Trim.TRIM RATE (Trim Rate)Initial value MinimumMaximum 10120advice Can do close adjustment when make a rate to trim small. but some of servo An enough effect isn't provided Please do a review of linkage, Before doing particular setting of trim.1 step of trim Be variable. Movement volume comes to have a small the one where a number is smallThe number of total step doesn't change. When change trim rate, The range that can adjust will change.Is cause to out of setting the trim when make a change with the situation that was already adjustedPress "EnterKey or "Back Key",change cursol to .And press "Back Key ",retuen to function menu list screen.Push "Enter" key. to enter setup menu. use "Jog dial" key or "+,-" keys. to adjust the value.Use "Jog dial" key or "+,-" keys. to choose the "TRIM.RATE" from Menu list.From initial screen. use "Jog dial" key or "+,-" keys. to open Function menu.[How to open the set-up screen.]DRAFT
Usage of the transmitter Features Main Menu Connecting the receiver Notes on installing Description Index60Back KeyEnter KeyJogDial+/- KeyResetFunction MenuAssign the function to ET, BTCan assign to ET or to BT Various functions.Some of function assign at first. but they can change it to customize.SET UPIndication contents of each function.OFF: NoneST TRIM: Steering TrimSUB TRIM: Steering Sub TrimTRAVEL: Steering TravelBRAKE: Trottle BrakeTH.SP-L: Throttle Speed (Low Speed)TH.SP-M: Throttle Speed (Medium Speed)TH.SP-H: Throttle Speed (High speed)ABS.W: ABS (Width)ABS.P: ABS (Position)ABS.C: ABS (Cycle)ACCEL.W: Throttle acceleration (Width)ACCEL.C: Throttle acceleration (Cycle)TH TRIM: Throttle TrimTH SPEED: Throttle Speed On/OffABS: ABS On/OffACCEL: Throttle acceleration On/OffUPTIM: Up TimerLAPTIM: Lap TimerDOWNTIM: Down TimerPRESET: Preset the ThrottleCH3: 3 channels controlDo set upSelect Item Select item with cursor to assign the function.If the function are already used, Function name will blink then the Redundancy function name will display at screen belowFunction name that can assign to each ET and BT.Function of 3 channel will appear if select at CH.SELECT the 3CH.OFF means not function.Push back key: cancel the setup and return to Setup menu. Push Enter key: accept changees of setup and return toSetup menu.Use Jog dial or +, - key to set function name. if it is alredy assign. Select ET or BT to assign the function by Jog dial or +, - keys.From menu list select SETUP then push Enter key.From initial screen open function menu by Jog dial or +, - keys.[How to open the set-up screen.]DRAFT
Usage of the transmitter Features Main Menu Connecting the receiver Notes on installing Description Index61Back KeyEnter KeyJogDial+/- KeyResetFunction MenuSetup UP timer to use.UP TIMERThey don’t have an allotment with an initial situation, a setup screen is displayed. If assign it to BT1.StartTrigger StartKey Start"READY" will blinkWhen time data is display push reset key to clear the displayStart when pull the trigger.There are two kinds of start methods.It starts with the assigned button.In an example, if BT1 is pushed, it will start.It can start, even if it is not a timer screen.Start CountingStopControl BT1It can start, even if it is not a timer screen.PausePush Enter keyOperation is possible only on a timer screen.It can not change to a setting screen.RestartControl BT1Or While pause and Timer screen was display push Enter keyResetWhile stop the timer (Include Pause) push Reset key.Can set While timer is stop (Can not setup while pausing).Set each itemAlarm is sounded after counting setting time.(Alarm tone can set (See page 29))Initial Value Off Min.Value 1 min Max.Value 99 minALARMP.ALARMCan set Pre Alarm before the AlarmInitial Value OFF Min.Value 1 sec Max.Value 30 secNAVISet LAP NavigationInitial Value OFF Min.Value 3.00 sec Max.Value 99.99 secWhen set NAVI, The button assigned to the rise timer needs reset-after pause operation on a timer screen to stop in order to function as reset of NAVI.Lap navigation function can set the target lap time.Can start with a button the same as "UP TIMER"Enter or Back key the cursor will back then push the back key to return at menu If not ET or BT assign it to lap timer, Setup will be displayed.From menu list, use Jog dial or "+, -" keys, and select the UP TIMER.Open the function menu. use Jog dial or "+, -" keys.[How to open the setup menu]"UP TIMER" is Simple Timer that add the time. but Can set LAP navigation function also.DRAFT
Usage of the transmitter Features Main Menu Connecting the receiver Notes on installing Description Index62Back KeyEnter KeyJogDial+/- KeyResetFunction MenuSet Down timerIt is a timer subtracted from time set up.Use When a timing of fuel refueling of an engine car is measured.DOWN TIMERIf assign to BT2StartControl BT2 to startit is not necessary to display the timer screen .Count indicationReset startControl BT2 to reset then re-startIt is not necessary to display the timer screenStopWhen Indicated 0m00s to the screen, the buzzer will alarm then timer will stopStop in timeReset key (push +, - key at the same time)it is necessary to display the timer screenAuto setActually functions to set the time that it took to a down timer.Ready to start"READY" will blinkStart at BT2When push reset button in Down timer screen. Auto start function will wait for start.While countingButtonDo a pouse and a start in turn whenever push a Enter key.Need to reset key operation If start Auto set then stop Less than 1 minute. (It will stop when power-off)Set up TimerInitial value 5 min.Min. value 1 min.Max value 99 min 59 sec.Initial value 0 sec.Min. value 0 sec.Max value 59 sec.Pre-alarmStop auto set function when push reset key While pouse.They don’t have an allotment with an initial situation, a setup screen is displayedUse Auto set, then Run the car till empty the fuel. When set pre alarm, can usable as a refueling timerNeed to assign any button to use this function.Can assign the custom tone at alarm of Down timer function.(see page 29)Subtracted from time set up on Down Timer.If not ET or BT assign it to lap timer, Setup will be displayed.From menu list, use Jog dial or "+, -" keys, and select the DOWN TIMER.Open the function menu. use Jog dial or "+, -" keys.[How to open the set-up screen.]DRAFT
Usage of the transmitter Features Main Menu Connecting the receiver Notes on installing Description Index63Back KeyEnter KeyJogDial+/- KeyResetFunction MenuCan count the every lap by using Lap timer.Set the Lap timer function and measurement point to record the lap.unestablished any key at an initial situation.LAP TIMERStart"READY" blinkPull the Trigger, to start countingWhile countingCounter displayENT Do Pause and restart in turnPauseCan not move the cursor during pause.+- When Push the Reset key during pause. all lap record will clear.Lap RecordsStart counting when push the Assigned button.StopNeed to set Alarm time.A timer stops by controlling a button after time progress.Alarm Time SetupLap Timer AlarmPre-Alarm TimeLAP Timer Pre-AlarmDisplay Lap TimeNext time start recorded from displayed LAPIn this case start recording from LAP 2.Delete Lap recordPush "ENTER" button to change the cursor.Push "ENTER" or "BACK" button to cancel.Delete all Lap records.While push "ENTER" button then Push together the "+ and -" button. to clear all LAP recordsTogetherThey don’t have an allotment with an initial situation, a setup screen is displayed.If assign to BT2advice The lap time record at Lap timer will save at same place. but the set up is Independent at each memory.Can use custom tone at alarm. (see page 29 and page 30)Can use 3 kind of timer at same times. (UP Timer, Down Timer, Lap Timer)Can record till 80 laps. after 80 laps over-write to 81st lap the 1st lap.If not ET and BT assign it to lap timer, Setup will be displayed.From menu list, use Jog dial or "+, -" keys, and select the LAP TIMER.Open the function menu. use Jog dial or "+, -" keys.[How to open the set-up screen.]
Usage of the transmitter Features Main MenuFunction MenuNotes on installing Description Index64Connecting the ReceiverSteering Servo7.2V FET ServoReceiverElectric Speed ControlerConnecting the receiverFor an electric-powered car For a gasoline-powered car (6V servos)For a gasoline-powered car  (7.2V FET Servos)5N600mAh6VNicd Battery Switch HarnessThrottle ServoSteering ServoReceiver6N600mAh7.2VNicd BatteryThrottle ServoSteering Servo7V Reguletor Switch HarnessReceiverKR-302FI'm sorry, I forgot it. Please give me grometts ~~~~~~!!How did you get this scratch?(FET servo + FET ESC)CH3Crystal replacementCH2 BATTSwitch HarnessESC or Throttle ServoCH1Steering ServoAntenna LeadWarning! Be certain to use only KO Propo genuine FM crystal sets(transmitter and receiver). Never use crystals produced by other companies since such crystals may vary in frequency, which could lead to misoperation or out of control.Warning! Be sure to use grommets and be sure that the servo is not touching any metal plates directly. * The vibrations may damage the servo and the model may run out of control.Warning! Be sure to connect all equipment correctly. If connections are loosened by vibration,the model may run out of control.Caution! Be sure to use genuine KO Propo products e.g. transmitter,receiver, ESC and other optional parts. * We cannot assume any responsibility for the use of other companies products with this unit.Warning! Do not cut or bundle the aerial wire with other cords. It may result in decreasing the sensitivity of the receiver and may result in the model running out of control.Caution! Be careful not to reverse the polarity of the transmitter and the receiver. Reverse polarity could damage the units.Connecting the receiverDRAFT
Usage of the transmitter Features Main MenuFunction MenuNotes on installing Description Index65Connecting the ReceiverAntenna LeadAntenna LeadAntenna LeadKR-297FZ KR-301F KR-302FWhen the frequency to be used is exchanged in a frequency band.For changing the frequency band to be used.The crystal of a transmitter and a receiver is exchanged for the thing of the frequency to be used.With models of receiver to be used, the order of a row of each channel and a battery channel changes. Please connect a connector after a check of a display. Keep in mind that it does not operate even if it connects Servo and ESC to a battery channel.Exchange of a frequency band is possible by exchanging RF module of use. An exchangeable frequency band is restricted to the frequency band permitted in each country which uses it.BATTBATTSwitch HarnessSwitch HarnessBATTSwitch HarnessCH3CH3CH2 CH2 CH2 ESC or Throttle ServoESC or Throttle ServoESC or Throttle ServoCH1Steering ServoCH1Steering ServoCH1Steering ServoAbout frequency changeConnecting the receiverDRAFT
Usage of the transmitter Features Main MenuFunction MenuConnecting the receiver Description Index66Notes on installing-1Because this is also part of the antenna, it is easier to pick up nearby noise.The Source of Noise and Electromagnetic Induction (Electric-powered car)Distance Between the Receiver and Antenna HolderMetals and carbon can also conduct noise. As a result, you should neverclosely attach the antenna wire to the plate and carbon chassis.Notes on installingAssume that all areas where large currents are flowing are generating noise!Locate antenna wires and receivers as far away from the motor, ESC, nicad batteries,and silicone wire as possible. Noise is a type of radio wave, and therefore is radiated (travel through the air) in the same fashion. Therefore, locating an antenna near a noise source increases the effect of the noise.Install the antenna holder as near to the receiver as possible.The easier it is for the antenna to pick up noise,the sensitivity of the receiver will decrease.DRAFT
Usage of the transmitter Features Main MenuFunction MenuConnecting the receiver Description Index67Notes on installing-2The installation position should be as far as possible from the motor, ESC, nicad batteries, silicone wires or other noise sources.Especially, do not route the silicone wires next to the receiver. (must not be near to the crystal)FET servo blue wire (7.2V wire) and switches can also generate noise, position them as far away as possible from the receiver and the antenna.When fixing the receiver in place on the chassis or on the "mechanical plate", use two pieces of double-sided tape, one on top of the other, as that the receiver is cushioned somewhat.Be sure that the crystal is on the high end when installing the receiverNotes on Installing the ReceiverMounting the Receiver (Electric-powered car)Notes on Installing Position (Do not near the reciever item.)Notes on installingDo not position the receiver or the antenna on the top of the motor or the nicad batteries.When mounting the receiver and antenna on the "upper deck", position them as far away from the nicad batteries and motor as possible.AntennaThe silicone wire passes directly over the receiver.Do not allow the silicone wires to cross the antenna. Do not position the antenna opening or the crystal near the nicad batteries, motor, or the carbon chassis.Do not route the wires near the antenna.Do not mount the receiver directly on the chassis or "mechanical deck"Use two layers of double-sided tape. Do not position the crystals on the bottomAlways position the crystal on the topDRAFT
Usage of the transmitter Features Main MenuFunction MenuConnecting the receiver Description Index68Notes on installing-3Bracket SpongePiano wire Pipe PipeAluminium holder Aluminium holder Plastic holderMetal, carbon(OK if FRP or plastic)Metal, carbon(OK if FRP or plastic)Soldered to lug boardMetal, carbonDo not secure antenna wire to the plateNotes on Installing the Receiver (Gasoline-powered car)Notes on Antenna InstallationNotes on installingDo not secure the receiver on the chassis or the "mechanical deck". Vibrations will cause the receiver to misfunction and may even cause internal damage to the receiver. Either use the bracket (receiver holder) provided with the kit, or else cushion the receiver with a sponge like material.Please follow the instruction as in the illustration below when you mount the antenna holder to the metal or carbon chassis.When using on FRP or carbon hollow antenna on a racing car, etc., do not pass the antenna wire through the pipe, allow it to trail away loosely outside.The exhaust gas of engine carries neither in this place nor the place which becomes high temperature. * A receiver breaks down and it becomes the cause of a reckless run.DRAFT
Usage of the transmitter Features Main MenuFunction MenuConnecting the receiver Notes on installing Description Index69Main SpecificationsMain SpefcificationsTransmitter KT-303HOperation methodNumber of channelsTransmission FrequencyNeutral pulseMemorySupply VoltageCurrent consumpionWheel+ Triger3 ChannnelsAny Band by changing crystalswithin the frequency range1.5msecEEPROM8x AA size dry cel or 8 cells NicadLess than 250mARF Module RF-501F for KT-303HTransmission Frequency rangeModulation methodAny frequency range byswitchung RF modulesFM-PPMReceiver KR-302FReception methodNumber of channelsReception frequencyIF frequencySupply voltageDimentionsWeighFM-PPM3 ChannelsAny Band by changing crystalswithin the frequency range455KHz3.5 6.5V29.3 24.4 16.4mm12.0 (excluding crystal)DRAFT
Usage of the transmitter Features Main MenuFunction MenuConnecting the receiver Notes on installing Index70DescriptionDescriptionTerminology used in radio control mode usage.Please refer to the Index for theterminology or wording of this transmitter.Analog Servo The general term of a model of machines of the Servo which used a thing of an analog method for control IC of ServoAlarm A signal to be famous as a buzzer of a transmitter.When it is used for a meaning of warning.Amplifier ESCESC Abbreviation of an electric speed controller.It is a speed controller of a motor to use by electric car.An amplifier is said.EEPROM A kind of memory.Contents written in aren't erased even if switched off.It is used for data pack in EEPROM others of memory in the main bodyInternet The network where the communication network where plural personal computers were connected to was connected to on a large scale more.Information dispatch by a homepage and an E-mail are depended on in the world, and communication can be done.WEB Site Home PageAM An electric wave to send from a transmitterA signal form of an electric wave.There is FM as another method.AM is an abbreviated designation in English of an amplitude modulation method.When that is used,It is had to match a signal form of transmission and reception machine.LCD A cable address to mean liquid crystal indication device.It is used to display letters.AC Charger A charge container to connect to 100V outlet.There are many situations to cut more than several hours in charge.FM A signal form of an electric wave to send from a transmitter.FM is an abbreviated designation in English of a frequency modulation methodFET An electric field effect transistor.Loss resistance is small, and, in comparison with a normal transistor, a consumption electric current of oneself is small, too.FET Servo FET was used for a motor drive element instead of a conventional transistor, and it is being of high class Servo.ET An Abbreviation of electric trim. Besides, a button is abbreviated to BT.Fast Charger The Charger which charges a nickel-cadmium battery and a nickel metal hydride battery by a short time.Carburetor Fuel mixture device, turn number of engines are controlled.Crystal A component to set frequency of transmission and receiver, It is made from crystal.Clutch An output axis of an engine and the intermittent continuation device which there is between gearing devices.High frequency ESC (an amplifier)ESC of the method how frequency to drive a motor is high.Most are these systems, but the thing which isn't a high frequency system exists in past things.High frequency (RF) moduleAn electric wave is made, and a circuit device to fire can be put on and off.When a frequency band to use (27MHz .40MHz) is changed, it is had to swap it.Connector Electric point of contact unit of putting on and off type.Rubber Grommet The rubber component which protects Servo from vibration, an edge of a Servo case can be possessed.Servo The device which converts a management signal of a transmitter into turn machine exercise.A Servo motor.Cycle It is space and period of repetition of a certain movement.CPU IC of a core of a computer used in various uses by digital operation processing.A microcomputer. It can be called MPU.Frequency band It is called the place that each frequency gathers, and shine, 27MHz zone (mega Hz), 40MHz zone.Receiver (RX) The device which an electric wave of a transmitter is received, and send a control signal forth in Servo and ESC.Jog dial A knob for data modification of a turn system not to have a stopper.If that is controlled every one click, by 1 point can do data modification, but is usable usefully when numerical value wants to be made a change in at a stretchSpeed controller ESCSwing Campaign against coming and going between a certain set two points.Spline Exact location of the servo horn in to the neutral position.Center Trim Even if the trim is adjusted, overall turning angle point will not be changed.DRAFT
Usage of the transmitter Features Main MenuFunction MenuConnecting the receiver Notes on installing Index71DescriptionDescriptionServo Saver Horn The shock absorbing device that is installed or in place of servo horn.Transmitter (TX) Hand set that transmitter signal.Turning Angle (Travel) Turning angle of the servo horn.Channel (CH) Number of Servo which can be controlled with a transmitter one by one.Or it is a number of that individual signalData Pack It is the module which had memory for enlargement built-in.Usable model memory can be increased.Digital Servo The general term of a model of machines of the Servo which used a thing of a digital system for control IC of Servo.Delay Act slowly.DC Charger The Charger which uses direct current for power supplies such as 12V battery or 12V stabilization power supply.Duty It is the ratio of two movement.Travel It is a rudder angle, movement volume.Trigger Control mechanism of a transmitter. A piece pulled with a finger to control the speed or brakes.Trim The device which adjusts a neutral position of each channel signal.7.2V Servo The Servo that a motor becomes the other power supply.By a KO PROPO original system, it is expected that a power supply is taken out of a power supply for power (7.2V) in the case of an electric carNiCad (Ni-cd) It is different from a dry cell,The battery which it is charged repeatedly, and can be used.There are NiMH or lithium ion as the battery which it is charged, and can be used repeatedly elsewhereNeutral The situation that separated a hand from a stick of a transmitter or a position of Servo Horne at that time.27Mhz It is for one of the frequency band that it can use by radio control, ground, water model, and there are 12 belts.Noise An electric noise.For a kind of electric wave, it makes it jumps into a receiver and malfunction.Band plate It is frequency and is selected with crystal glass.It can make a change by crystal glass exchange in the same frequency band.Band It is frequency and is selected with crystal glass.It can make a change by crystal glass exchange in the same frequency bandBacklight Because themselves don't emit light LCD (a liquid crystal display), visibility isn't good by the time if it is dark.It is the lamp which is installed in the backside of liquid crystal to solve this (the emission of light source)Dead Band The field where Servo doesn't react to even if it controls foil and trigger.VR It means the volume that detects the position of the stick.Fail safe adaptor When it receives an interference electric wave, it is the device which it fixes Servo Horne at the position that a computer set up beforehand, and prevent reckless driving.Push rod The stick thing which is used for linkage.Preset Will set up a position in advancePC interface It is an adapter it converts a signal into, and to be connected to do setting of a transmitter with a PC.Discharger The circuit device which makes you discharge a residual quantity of a charge type battery of NiCad forcibly.Wheel Mechanism of the transmitter which it turns it from side to side, and control a steering.Pumping Effect Intermittent breaking action.Home Page It says the place where it mentioned a certain information in on Internet.It can look by software on a personal computer called a Web browser.Machine plate The board which installs receiver Servo on a chassis of a car.Mega Hz (MHz) 1000Hz =1 KHz (a kilohertz) 1000KHz =1MHz.Memory In a personal computer, it is used for a meaning called the preservation place in which information is stored temporarily. Although the information on the memory in this case will be lost if a power supply is shut off, the memory used for a transmitter etc. is called non-volatilized memory, and even if it shuts off a power supply, it holds information.40Mhz One of the frequency band that it can use by radio control. Eight bands for ground model. There are five bands for sky model.Linkage Servo and connection mechanism to connect each mechanism to of a model.Reset Return setting contents of setting numerical value to an initial situationRegulator The circuit which stabilizes the input voltage to the necessary voltage.Response It is time before machinery of the receiver side reacting since it controls a transmitter.Width The thing of width which operates by ABS or Throttle Acceleration.DRAFT
Usage of the transmitter Features Main MenuFunction MenuConnecting the receiver Notes on installing Description72IndexDRAFT
Usage of the transmitter Features Main MenuFunction MenuConnecting the receiver Notes on installing Description73IndexDRAFT
Usage of the transmitter Features Main MenuFunction MenuConnecting the receiver Notes on installing Description Index74DRAFT

Navigation menu