LG Electronics USA 3G1XINBTS STAREX-IS 1900 Indoor BTS User Manual STAREX IS User s Manual
LG Electronics USA STAREX-IS 1900 Indoor BTS STAREX IS User s Manual
Contents
Users Manual Part D
STAREX-IS BSM Manual Fig. 4.5-27 Traffic Path Release Command Execution Result Display(Interm Window) Fig. 4.5-28 Traffic Path Release Command Execution Result Display(Console Window) SMD-011-PMA210 Page:449(877) Issue:1.0 STAREX-IS BSM Manual 4.5.7. Call Trace Testing Function Mobile Call Trace Function traces the process of call setup for the MS, surveillance of the status after the call setup, the process of call release, and displays the content visibly to BSM after BSM of User’s terminal designates a Mobile Station(MS) at random by using a value of MSIN(Mobile Station Identification Number). . The designated Mobile Station(MS) can trace the originating call or terminating call that was set up by the user and if necessary, it sets up Markov call(i.e., a terminating Markov call by paging) for tracing. Mobile call tracing can be performed to all kinds of calls(Voice Call, Data Call, HandOff Call) and can designate maximum two calls simultaneously for tracing. Information provided upon call tracing is as follows: Tracing Information when Call is set Resource of Call to be set System Resource: BSC No, BTS No, Sector No, PN Offset Attributes of Call: IMSI, ESN, Service Option, Call Type(Voice Call originating, Voice Call terminating, DATA Call initial set, DATA Call Reactivation by MS, DATA Call Reactivation by Network), Terminating number BTS Resource: CDMA CH(Frequency) No, TC No(RCP#, MCPA#, CE#), Code CH(Walsh code), Frame Offset BSC Resource: SLP, VCE Number, CIC(Circuit Identifier Code) Setup Process Message display between processors during Call Setup: Visible Display of Call Flow During Call Setup, display RTD(Round Trip Delay) value and calculated distance by using this. When Call Failure occurs, display reason value and its meaning Call Set Time by section Tracing Information at the phase of calling after Call Setup: Tracing and Display at intervals of 1 ~ 5 seconds. Elements of Communication Quality Forward FER(Frame Error Rate): Present FER, Total FER Backward FER(Frame Error Rate): Present FER, Total FER Power Control Parameter: TC Gain, Reverse Power Control Threshold Location Estimate Elements Present Active PN Offsets Aggregation : BSC No, BTS No, Sector, Cdma Ch, Walsh_ch, TC Id, RTD SMD-011-PMA210 Page:450(877) Issue:1.0 STAREX-IS BSM Manual Present RTD Value and calculated distance by using this Tracing Information at the phase of Call Release: Tracing it every time at the normal release or abnormal release Reason for Call Release Reason for Call Release and its content: Display reason value and its meaning Quality Elements of Call Forward Total FER(Frame Error Rate) Backward Total FER(Frame Error Rate) 4.5.7.1. Call Trace Start/End Function Function that starts/ends Call Trace with MS designated at random. • Command TRC-CALL : IMSI=a, ITEM=b,BSC=c; a: IMSI Number b: Start / Stop c: BSC ID • Input/Output Fig. 4.5-29 Call Trace Start Command Input Screen SMD-011-PMA210 Page:451(877) Issue:1.0 STAREX-IS BSM Manual Fig. 4.5-30 Call Trace Display in the Process of Call Set SMD-011-PMA210 Page:452(877) Issue:1.0 STAREX-IS BSM Manual Fig. 4.5-31 Display of Call Set Process and Elements of Communication Quality SMD-011-PMA210 Page:453(877) Issue:1.0 STAREX-IS BSM Manual Fig. 4.5-32 Display of Communication Quality and Release Reason Fig. 4.5-33 Call Trace Stop Result SMD-011-PMA210 Page:454(877) Issue:1.0 STAREX-IS BSM Manual 4.5.7.2. Call Trace MS Display Function Function to display MS that currently uses • Command the mobile call tracing function. DIS-TRC-MS; • Input/Output Fig. 4.5-34 Terminal Display in use of Call Trace SMD-011-PMA210 Page:455(877) Issue:1.0 STAREX-IS BSM Manual 4.5.8. Number of (Active/Dormant) Data Call User Display Function Function to display Number of Data Call by Active/Dormant • Command DIS-DATA-CALL:PCP=a; a: PCP Number(0~2) • Input/Output Fig. 4.5-35 Result of the Number of DATA Call User Display SMD-011-PMA210 Page:456(877) Issue:1.0 STAREX-IS BSM Manual 4.5.9. DATA Call User Status Display Function by IMSI Command DIS-DATA-STS:PCP=a,IMSI=b; a: PCP Number(0~2) b: IMSI of MS • Input/Output Fig. 4.5-36 Result of DATA Call User Status Display by IMSI SMD-011-PMA210 Page:457(877) Issue:1.0 STAREX-IS BSM Manual 4.5.10. IOS Message Display Function This function is operated by inputting the IMSI of MS to trace, duration, etc in BSM and displays IOS trace information for all kinds of calls that MS attempts as visible information in text format in the BSM. • Command TRC-IOS : MS=a, BSC=b, FLAG=c, DURATION=d a: MS Number b: BSC ID(0~11) c: Start/Stop d: Trace Duration Time • Input/Output Fig. 4.5-37 IOS Message Display START Result SMD-011-PMA210 Page:458(877) Issue:1.0 STAREX-IS BSM Manual Fig. 4.5-38 IOS Display Message SMD-011-PMA210 Page:459(877) Issue:1.0 STAREX-IS BSM Manual Fig. 4.5-39 STOP Result of IOS Message Display Function SMD-011-PMA210 Page:460(877) Issue:1.0 STAREX-IS BSM Manual 4.5.11. POWER MONITORING Function Function to check the BTS power control in BSM • Command DIS-BTS-PWR:BSC=a,BTS=b,ITEM=c,[TIME=d]: a: BSC ID(0~11) b: BTS ID(0~47) c: Stop/Start d: Duration Time(1~100 min) • Input/Ouput Fig. 4.5-40 Power Monitoring START Result SMD-011-PMA210 Page:461(877) Issue:1.0 STAREX-IS BSM Manual Fig. 4.5-41 Power Monitoring Result Fig. 4.5-42 Power Monitoring STOP Result SMD-011-PMA210 Page:462(877) Issue:1.0 STAREX-IS BSM Manual 4.6. No.7 Command The function of BSM No.7 is to manage parameter information necessary for the operator to operate No.7. It is divided into the following function: 1) signaling link operation management and 2) the signaling link maintenance. The former is composed of the following: signaling point management function, signaling link set management function, signaling link management function, signaling terminal management function, signaling data management function, and SCCP management function. The latter is composed of signaling link and signaling terminal test, and signal link inhibit. 4.6.1. Related Command 4.6.1.1. Commands for Signaling Link Operation and Management Function Table 4.6-1 Commands related to Signaling Point Management Commands Description DIS-SP-INFO Signaling Point Information Display CHG-OSP Change of Intra-Switching Office Signaling Point CHG-SP Change of Signaling Point Table 4.6-2 Commands related to Signaling Link Set Commands Description ACT-LKS Signaling Link Set Activation DACT-LKS Signaling Link Set Deactivation Table 4.6-3 Commands related to Signaling Link Commands Description CRET-SLK Signaling Link Create DEL-SLK Signaling Link Deletion ACT-SLK Signaling Link Activation DACT-SLK Signaling Link Deactivation SMD-011-PMA210 Page:463(877) Issue:1.0 STAREX-IS BSM Manual DIS-SLK-INFO Signaling Link Information Display INH-SLK Signaling Link Barring ALW-SLK Signaling Link Barring Release Table 4.6-4 Commands related to Signaling Terminal Commands Description CRTE-ST Signaling Terminal Definition(Create) DEL-ST Signaling Terminal Deletion DIS-ST-INFO Signaling Terminal Information Display Table 4.6-5 Commands related to Signaling Data Link Commands Description CRTE-SDLK Signaling Data Link Definition(Create) DEL-SDLK Signaling Data Link Deletion DIS-SDLK-INFO Signaling Data Link Information Display Table 4.6-6 Display Commands for SCCP Data Commands Description DIS-SCCP-NET SCCP Network Configuration Data Display DIS-SCCP-LSS SCCP Intra-Switching Office Sub-system Status Data Display Table 4.6-7 Signaling Link Status Display Commands Commands Description DIS-SLK-STS Signaling Link Status Display DIS-ST-STS Signaling Terminal Status Display DIS-LKS-STS Signaling Link Set Status Display Table 4.6-8 Commands related to Timer SMD-011-PMA210 Page:464(877) Issue:1.0 STAREX-IS BSM Manual Commands Description DIS-MTP2-TMR MTP L2 Timer Display CHG-MTP2-TMR MTP L2 Timer Change DIS-MTP3-TMR MTP L3 Timer Display CHG-MTP3-TMR MTP L3 Timer Change DIS-SCCP-TMR SCCP Timer Change CHG-SCCP-TMR SCCP Timer Change 4.6.1.2. Commands for Signaling Link Maintenance Function Table 4.6-9 Test Related Commands Commands Description TEST-SLK Signaling Link Test TEST-ST Signaling Terminal Test DIS-No7-CYC Test Cycle Display CHG-No7-CYC Test Cycle Change Table 4.6-10 Status Suppression Related Commands Commands Description DIS-INH-NO7 Displayable Status Message Display ALW-N07-MSG Status Message Display Possible INH-NO7-MSG Status Message Display Suppression 4.6.2. Signaling Link Operation Management Function 4.6.2.1. Signaling Point Information Display Display the Status of Signaling Point of local Switching Office and that of IntraSwitching Office. Command DIS-SP-INFO:BSC_ID=a a = BSC Number (00 ~ 11) Input DIS-SP-INFO:BSC_ID=0; SMD-011-PMA210 Page:465(877) Issue:1.0 STAREX-IS BSM Manual Output Fig. 4.6-1 Signaling Point Information Display 4.6.2.2. Change of Intra-Switching Office Signaling Point It changes Information for Intra-Switching Office Signaling Point. Command CHG-OSP:BSC=a,OSP_NUM=b; a = BSC Number( 00 ~ 11 ) b= OSP Number ( 00 ~ 65535 ) Input CHG-OSP:BSC_ID=0,OSP_NUM=5; Output Fig. 4.6-2 Change of Intra-Switching Office Signaling Point 4.6.2.3. Change of Local Switching Office Signaling Point It changes Signaling Point of Local Switching Office. Command CHG-SP-INFO:BSC_ID=a, SP_NUM=b SMD-011-PMA210 Page:466(877) Issue:1.0 STAREX-IS BSM Manual b = SP Number ( 00 ~ 65535 ) Input CHG-SP-INFO:BSC_ID=0,SP_NUM=1038 Output Fig. 4.6-3 Change of Remote Switching Office Signaling Point 4.6.2.4. Activation of Signaling Link Set Signaling Link Set indicates an aggregation of signaling links(Max 16 units). Activation of Signaling Link Set is to put all the defined Signaling Links in a in-service status. Command ACT-LKS:BSC_ID=a a = BSC Number ( 00 ~ 11) Input ACT-LKS:BSC_ID=0; Output SMD-011-PMA210 Page:467(877) Issue:1.0 STAREX-IS BSM Manual Fig. 4.6-4 Activation of Signaling Link Set 4.6.2.5. Deactivation of Signaling Link Set Function that puts all the defined Signaling Links in out-of-service status Command DACT-LKS:BSC_ID=a; a = BSC Number ( 00 ~ 01 ) Input DACT-LKS:BSC_ID= a; Output Fig. 4.6-5 Deactivation of Signaling Link Set SMD-011-PMA210 Page:468(877) Issue:1.0 STAREX-IS BSM Manual 4.6.2.6. Signaling Link Generation Signaling Link is the concept combing Signaling Data Link with Signaling Terminal. It connects Intra-Switching Office Signaling Point to local switching Office Signaling Point, and can define 16 units of Signaling Link. The definition of Signaling Link is used to expand the number of Signaling Links. Before Signaling Link is defined, first of all, Signaling Terminal and Signaling Data Link to be defined as Signaling Link should have been defined. Command CRTE-SLK:BSC=a, SLK=b, VMP=c, TRK=d, TS_NO = e, ST_ID =f; a = BSC Number ( 00 ~ 11 ) b = Signalling Link Code ( 00 ~ 15 ) c = VMP ( 00 ~ 07 ) d = Trunk Number ( 00 ~ 16 ) e = Time Slot Number ( 00 ~ 31) f= Input Signalling Terminal ( 1 ~ 16) CRTE-SLK:BSC=0, SLK =5, VMP = 00, TRK = 5 TS_NO=16, ST_ID = 5; Output Fig. 4.6-6 Signaling Link Create 4.6.2.7. Signaling Link Deletion Function to delete the defined Signaling Link.Before the Signaling Link is deleted, the corresponding Signaling Link should have been successfully deactivated. Command DEL-SLK:BSC_ID=a, SLC =b; a = BSC Number ( 00 ~ 11 ) SMD-011-PMA210 Page:469(877) Issue:1.0 STAREX-IS BSM Manual b = Signalling Link Code Input ( 00 ~ 15 ) DEL-SLK:BSC=0, SLC =3; Output Fig. 4.6-7 Deletion of Signaling Link 4.6.2.8. Signaling Link Activation Function to activate a defined Signaling Link. Before activated, the corresponding Signaling Link should have been successfully defined. Command ACT-SLK:BSC_ID=a, SLC; a = BSC Number ( 00 ~ 11 ) b = Signalling Link Code ( 00 ~ 15 ) Input ACT-SLK:BSC_ID=0, SLC=2; Display SMD-011-PMA210 Page:470(877) Issue:1.0 STAREX-IS BSM Manual Fig. 4.6-8 Activation of Signaling Link 4.6.2.9. Signaling Link Deactivation Function to deactivate the activated Signaling Link. Command DACT-SLK:BSC=a, SLC=b; a = BSC Number ( 00 ~ 11 ) b = Signalling Link Code ( 00 ~ 15 ) Input DACT-SLK:BSC_ID=0, SLC = 2; Output SMD-011-PMA210 Page:471(877) Issue:1.0 STAREX-IS BSM Manual Fig. 4.6-9 Deactivation of Signaling Link 4.6.2.10. Signaling Link Information Display Function to display information on Signaling Terminal, Signaling Data Link and Bit_Rate connected to Signaling Link. It can display information on entire Signaling Links and on Signaling Link designated. Command DIS-SLK-INFO:BSC_ID=a; a = BSC Number ( 00 ~ 15 ) Input DIS-SLK-INFO:BSC_ID = 0; Output Fig. 4.6-10 Signaling Link Information Display 4.6.2.11. Signaling Link Inhibition It inhibits the use of presently defined Signaling Link. Command INH-SLK:BSC_ID=0, SLC =0; a = BSC Number ( 00 ~ 11 ) b = Signalling Link Code ( 00 ~ 15 ) Input INH-SLK:BSC_ID=0, SLC=0; Output SMD-011-PMA210 Page:472(877) Issue:1.0 STAREX-IS BSM Manual Fig. 4.6-11 Signaling Link Inhibit 4.6.2.12. Signaling Link Allow Signaling Link Allow is a function that allows the management of Signaling Link Status inhibited in the management of Signaling Link and then change to the status of availability. Command ALW-SLK:BSC_ID=0, SLC =0; a = BSC Number ( 00 ~ 11 ) b = Signalling Link Code ( 00 ~ 15 ) Input ALW-SLK:BSC_ID = 0, SLC = 0; Output SMD-011-PMA210 Page:473(877) Issue:1.0 STAREX-IS BSM Manual Fig. 4.6-12 Signal Link Allow 4.6.2.13. Signal Terminal Addition Signal Terminal indicates physical name of a Channel of STPA and can define 16 units of Signaling Terminal at a maximum. It is used to expand Signaling Terminal. Command CRTE-ST:BSC=a, ST_ID=b; a = BSC Number ( 00 ~ 15 ) b = Signalling Terminal ( 01 ~ 16 ) Input CRTE-ST:BSC_ID=0,ST_ID = 4; Output Fig. 4.6-13 Signaling Terminal Generation 4.6.2.14. Signaling Terminal Deletion It is used when Signaling Terminal H/W has problems or other faults occur. Before Signaling Terminal is deleted, make sure that the corresponding Signaling Terminal is connected to Signaling Link. Command DEL-ST:BSC=a, ST_ID =b; a = BSC Number ( 00 ~ 11 ) b = Signalling Terminal ( 01 ~ 16 ) Input DEL-ST:BSC_ID=0,ST_ID = 5; Output SMD-011-PMA210 Page:474(877) Issue:1.0 STAREX-IS BSM Manual Fig. 4.6-14 Signaling Terminal Deletion 4.6.2.15. Signaling Terminal Information Display Function to display information about if it is linked with signaling link to a specific Signaling Terminal or all the Signaling Terminals. Command DIS-ST-INFO:BSC_ID =a; a = BSC Number ( 00 ~ 11 ) Input DIS-ST-INFO:BSC_ID = 0; Output Fig. 4.6-15 Display of Signaling Terminal Information SMD-011-PMA210 Page:475(877) Issue:1.0 STAREX-IS BSM Manual 4.6.2.16. Signaling Data Link Addition Signaling Data Link indicates Trunk Number to allocate as Signaling Link and is used to expand Signaling Data Link. Command CRTE-SDLK: BSC =a, VMP_ID=b, TRK= c ,TS_NO=d; a = BSC Number ( 00 ~ 11 ) b = VMP Number( 00 ~ 07 ) c = TRUNK Number( 00 ~ 16 ) d = Time Slot Number( 00 ~ 31 ) Input CRTE-SDLK: BSC_ID=0, VMP_ID=1, TRK=0 , TS_NO=16; Output Fig. 4.6-16 Signaling Data Link Generation 4.6.2.17. Signaling Data Link Deletion It is used when Signaling Data Link H/W is defective or other problems occur.Before deleting the Signaling Data Link, make sure that corresponding Signaling Data Link is allocated to Signal Link and then delete. Command DEL-SDLK;BSC=a, VMP=b, TRK=c, TS_NO=d; a = BSC Number ( 00 ~ 11 ) b = VMP Number( 00 ~ 07 ) c = TRUNK Number( 00 ~ 16 ) d = Timer Slot Number( 00 ~ 31 ) SMD-011-PMA210 Page:476(877) Issue:1.0 STAREX-IS BSM Manual Input DEL-SDLK:BSC=0, VMP=0, TRK= 5, TS_NO = 16; Output Fig. 4.6-17 Signaling Data Link Deletion 4.6.2.18. Signaling Data Link Information Display Function to display information on the defined Signaling Data Link and the status connected to Signaling Link. Command DIS-SDLK-INFO: BSC_ID = a; a = BSC Number ( 00 ~ 11 ) Input DIS-SDLK-INFO: BSC_ID=0; Output SMD-011-PMA210 Page:477(877) Issue:1.0 STAREX-IS BSM Manual Fig. 4.6-18 Signaling Data Link Information Display 4.6.2.19. SCCP Network Configuration Data Display Function to display SCCP Network Configuration Data for Intra-Switching Office Signaling Point, local Switching Office Signaling Point, and each sub-system. Command DIS-SCCP-NET:BSC_ID=a; a = BSC Number ( 00 ~ 11 ) Input DIS-SCCP-NET:BSC_ID=0; Output Fig. 4.6-19 SCCP Network Configuration Data Display SMD-011-PMA210 Page:478(877) Issue:1.0 STAREX-IS BSM Manual 4.6.2.20. SCCP Local Subsystem State Data Display Function to display State related to Local Exchange Sub-system defined at Local Exchange Signaling Point Command DIS-SCCP-LSS:BSC_ID =a; a = BSC Number ( 00 ~ 16 ) Input DIS-SCCP-LSS:BSC_ID = 0; Output Fig. 4.6-20 SCCP Local Subsystem State Data Display 4.6.2.21. Signaling Link Status Display Function to display a designated Signaling Link Status, Activate Status of Signaling Link, Inhibit Status of Intra switching office Signaling Link, and Inhibit Status of local Switching Office. Command DIS-SLK-STS:BSC_ID = a, SLC = b; a = BSC Number ( 00 ~ 11) b = Signalling Number Code ( 00 ~ 16 ) Input DIS-SLK-STS:BSC_ID = 0, SLC=0; Output SMD-011-PMA210 Page:479(877) Issue:1.0
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Modify Date : 2001:11:07 17:33:35-05:00 Create Date : 2001:11:07 17:33:12-05:00 Title : Microsoft Word - STAREX-IS User's Manual.doc Author : LG IBM PC USER Creator : ADOBEPS4.DRV Version 4.50 Producer : Acrobat Distiller 5.0 (Windows) Page Count : 31EXIF Metadata provided by EXIF.tools