LG Electronics USA MU50PZ40 50" Plasma Monitor User Manual 352A LG
LG Electronics USA 50" Plasma Monitor 352A LG
Users Manual
PLASMA MONITOR OWNER’S MANUAL MODEL : MU-50PZ40/41 MU-50PZ40A/41A MU-50PZ40B/41B MU-50PZ40K/41K MU-50PZ40R/41R MU-50PZ40S/41S Please read this owner’s manual carefully before operating the Monitor. Retain it for future reference. Record model number and serial number of the Monitor. See the label attached on the back of the Monitor and quote this information to your dealer when you require service. Model number : Serial number : P/NO : 3828VA0352A (RF02CA) WARNING WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. FCC NOTICE • MU-50PZ41/A/B/K/R/S : A Class A digital device This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. • MU-50PZ40/A/B/K/R/S : A Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. • Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. WARNING TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. SAFETY INSTRUCTIONS Important safeguards for you and your new product Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference. Observing the simple precautions discussed in this booklet can help you get many years of enjoyment and safe operation that are built into your new product. This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association. 1. Read Instructions All the safety and operating instructions should be read before the product is operated. 2. Follow Instructions All operating and use instructions should be followed. 3. Retain Instructions The safety and operating instructions should be retained for future reference. 4. Heed Warnings All warnings on the product and in the operating instructions should be adhered to. 5. Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. Water and Moisture Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. 7. Accessories Carts and Stands Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. 8. Transporting Product A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. case or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. 11. Power Sources This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Power-Cord Polarization This product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit into the grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 13. Power-Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 14. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. Example of Grounding According to National Electrical Code Instructions PORTABLE CART WARNING 9. Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards. 10. Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a book- Ground Clamp Antenna Lead in Wire Antenna Discharge Unit (NEC Section 810-20) Electric Service Equipment NEC - National Electrical Code Grounding Conductor (NEC Section 810-21) Ground Clamps Power Service Grounding Electrode System (NEC Art 250, Part H) (Continued on next page) SAFETY INSTRUCTIONS (Continued from previous page) 15. Lightning For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 16. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17. Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 18. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 19. Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 20. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e. If the product has been dropped or the cabinet has been damaged. f. If the product exhibits a distinct change in performance. 21. Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 22. Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 23. Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. 24. Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. The PDP Manufacturing Process: Why colored dots may be present on the PDP screen The PDP (Plasma Display Panel) which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products and the dots appearing does not mean that this PDP is defective. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology is designed to minimize cell defects. Cooling Fan Noise In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP. This noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the PDP to be exchanged or returned. Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4 Step 1. Monitor Installation & Setup Controls and Connection Options . . . . . . . . . . . .6 External Equipment Viewing Setups . . . . . . .7~10 Remote Control Key Functions . . . . . . . . . . . . .11 Monitor Accessories . . . . . . . . . . . . . . . . . . . . .12 Monitor Installation/Mounting Options . . . . . . . .12 Stand Installation . . . . . . . . . . . . . . . . . . . . . . .12 Step 2. Customize your Monitor’s Features Basic Features Setup and Operation Turning on the Monitor . . . . . . . . . . . . . . . . . . .13 Menu Language Selection . . . . . . . . . . . . . . . .13 Video Menu Options APC (Auto Picture Control) . . . . . . . . . . . . . . . .14 Adjusting Auto Color Control . . . . . . . . . . . . . . .14 Manual Color Temperature Control . . . . . . . . . .14 Manual Picture Control . . . . . . . . . . . . . . . . . . .14 Audio Menu Options DASP (Digital Auto Sound Processing) . . . . . . .15 AVL (Auto Volume Leveler) . . . . . . . . . . . . . . . .15 Adjusting Sound (Manual Settings) . . . . . . . . . .15 Time Menu Options Setting the Clock . . . . . . . . . . . . . . . . . . . . . . .16 Setting the On/Off Timer . . . . . . . . . . . . . . . . .16 Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Special Menu Options Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Orbiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 White Wash . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Screen Menu Options Auto Adjustment . . . . . . . . . . . . . . . . . . . . . . . .18 Setting Picture Format . . . . . . . . . . . . . . . . . . .18 Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Screen Position . . . . . . . . . . . . . . . . . . . . . . . .19 Manual Configure . . . . . . . . . . . . . . . . . . . . . . .19 Screen Adjustments . . . . . . . . . . . . . . . . . . . . .19 Initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 PIP (Picture In Picture) Feature Watching PIP/PIP Size/PIP Aspect Ratio . . . . . .20 Swapping PIP/ Moving PIP . . . . . . . . . . . . . . . .20 Selecting a Input Signal Source for PIP . . . . . . .20 Main Picture Size Adjustment . . . . . . . . . . . . . .20 Main Picture Position Adjustment . . . . . . . . . . .20 Twin Picture Setup Options Main Picture Size Adjustment . . . . . . . . . . . . . .21 Sub Picture Size Adjustment . . . . . . . . . . . . . . .21 Selecting a Source for the Twin Picture . . . . . . .21 Swapping the Twin Picture . . . . . . . . . . . . . . . .21 Step.3 Miscellaneous External Control Device Setup IR Code (NEC format) . . . . . . Maintenance . . . . . . . . . . . . . . Troubleshooting Checklist . . . . Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .22 . . . . . . . . . . . . .27 . . . . . . . . . . . . .29 . . . . . . . . . . . . .30 . . . . . . . . . . . . .31 After reading this manual, keep it handy for future reference. Monitor Controls Front Panel Controls VOL. ON/OFF MENU INPUT SELECT INPUT SELECT Button Power Standby Indicator Illuminates red in standby mode, Illuminates green when the Monitor is turned on Main Power Button MENU Button Remote Control Sensor VOLUME (F,G) Buttons D,E Buttons Connection Options Back Connection Panel EXTERNAL SPEAKER (8Ω) R AUDIO L (MONO) ( )R( ) AC INPUT AUDIO INPUT VIDEO INPUT S-VIDEO PB PR COMPONENT (DVD/DTV INPUT) ON/ OFF R AUDIO L AUDIO INPUT ( )L ( ) CONTROL REMOTE RGB1 OUTPUT AUDIO LOCK CONTROL (PC/DTV OUTPUT) INPUT RGB1 INPUT RGB2 INPUT RS-232C INPUT (PC/DTV INPUT) (DIGITAL RGB INPUT) (CONTROL/SERVICE) EXTERNAL SPEAKER 1. EXTERNAL SPEAKER (8 ohm output) Connect to optional external speaker(s). * For further information, refer to ‘Speaker & Speaker Stand’ manual. 5. CONTROL LOCK Switch REMOTE CONTROL When “CONTROL LOCK” is set “ON”, Monitor is operated by the external control device. 2. POWER CORD SOCKET This Monitor operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the Monitor on DC power. 6. RGB1 OUTPUT(PC/DTV OUTPUT) JACKS You can watch the RGB1 signal on another monitor, connect RGB1 OUTPUT (PC/DTV OUTPUT) to another monitor’s PC input port. 3. AUDIO/VIDEO INPUT JACKS Connect audio/video out from external equipment to these jacks. S-VIDEO INPUTS (S-VIDEO) Connect video out from an S-VIDEO VCR to the S-VIDEO input. 7. AUDIO INPUT/RGB1 INPUT(PC/DTV INPUT)/ RGB2 INPUT(DIGITAL RGB INPUT) JACKS Connect the monitor output socket of the PC to this socket. 4. COMPONENT(DVD/DTV INPUT)/AUDIO INPUT JACKS 8. RS-232C INPUT(CONTROL/SERVICE) PORT Connect to the RS-232C port on a PC. External Equipment Connections Monitor External Equipment Connection Panel R AUDIO L (MONO) ( )R( ) EXTERNAL SPEAKER (8Ω) AC INPUT AUDIO INPUT VIDEO INPUT AUDIO INPUT VIDEO INPUT S-VIDEO PB PR ON/ COMPONENT (DVD/DTV INPUT) S-VIDEO INPUT COMPONENT (DVD/DTV INPUT) Connection to AV equipment OFF R AUDIO L AUDIO INPUT ( )L ( ) CONTROL REMOTE RGB1 OUTPUT AUDIO LOCK CONTROL (PC/DTV OUTPUT) INPUT COMPONENT AUDIO INPUT RGB AUDIO INPUT RGB1 INPUT RGB2 INPUT RS-232C INPUT (PC/DTV INPUT) (DIGITAL RGB INPUT) (CONTROL/SERVICE) EXTERNAL SPEAKER RGB2 INPUT (DIGITAL RGB1 INPUT RGB INPUT) (PC/DTV INPUT) RS-232C INPUT Connection to PC Note: All cables shown are not provided with the Monitor, except: A D-sub 15 pin cable and DVI cable is supplied to connect the Monitor to a PC. External Equipment Viewing Setups Watching VCR Setup - When connecting the Monitor to external equipment, match the colors of connecting ports (Video - yellow, Audio (L) - white, Audio (R) -red). - Connect the VIDEO INPUT socket (yellow) with the BNC-RCA adapter to the VIDEO INPUT on the Monitor. - If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input on the Monitor. - If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input. - Use the orbiter function to Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. If a 4:3 picture format is used; the fixed image may remain visible on the screen. - To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor 1. Use the INPUT SELECT button on the remote control to select VIDEO. (If connected to S-VIDEO, select the S-VIDEO external input source.) 2. Insert a video tape into the VCR and press the PLAY button on the VCR. (See VCR owner’s manual) Watching Cable TV Setup - After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming. This monitor cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the Monitor. - For further information regarding cable TV service, contact your local cable TV service provider(s). 1. Use the INPUT SELECT button on the remote control and select VIDEO. 2. Tune to cable service provided channels using the cable box. Watching External A/V Source Setup - When connecting the monitor to an external source, match the colors of AUDIO/VIDEO input jacks on the monitor with the output jacks on the audio/video equipment: Video = yellow, Audio (Left) = white, Audio (Right) = red. 1. Use the INPUT SELECT button on the remote control to select VIDEO. 2. Operate the corresponding external equipment. See external equipment operating guide. Watching DVD Setup How to connect Connect DVD video inputs to Y, PB, PR of COMPONENT (DVD/DTV INPUT) and audio inputs to Audio sockets of AUDIO INPUT. How to use 1. Turn on the DVD player, and insert a DVD. 2. Use INPUT SELECT button on the remote control to select COMPONENT. Refer to the DVD player's manual for operating instructions. • Component Input ports You can get better picture quality if you connect DVD player with component input ports as below. Component ports of the Monitor Video output ports of DVD player PR PB Pr Pb B-Y R-Y Cb Cr PB PR Watching DTV Setup - To watch digitally broadcast programs, purchase/connect a digital SET-TOP BOX. How to connect a user-supplied Digital Set-Top Box • Connect DTV set-top box video output to monitor COMPONENT (DVD/DTV INPUT) or to the monitor RGB1 (PC/DTV INPUT) connector depending on your Set Top Box connectors. • Connect DTV set-top box audio outputs to monitor AUDIO INPUT jacks. How to use 1. Turn on the digital SET-TOP BOX. (Refer to the owner’s ,manual for the digital SET-TOP BOX.) 2. Use INPUT SELECT on the remote control to select COMPONENT or RGB 1. PC Setup - To enjoy vivid picture and sound, connect a PC to the Monitor. - Avoid keeping a fixed image on the monitor’s screen for a long period of time. The fixed image may become permanently imprinted on the screen; use a screen saver when possible. - Connect PC to the RGB1 INPUT(PC/DTV INPUT) or RGB2 INPUT(DIGITAL RGB INPUT) port of the Monitor; change the resolution output of PC accordingly. - Synchronization input form; Separate Setup Instructions to Connect a PC to your Monitor - If the resolution of PC is over UXGA, there will be no picture on the Monitor. - Connect the signal cable from the monitor output port of the PC to the RGB1 INPUT(PC/DTV INPUT) port of the Monitor or the signal cable from the DVI output port of the PC to the RGB2 INPUT(DIGITAL RGB INPUT) port on the Monitor. - Connect the audio cable from the PC to the Audio input on the Monitor. (Audio cables are not included with the Monitor). - If using a sound card, adjust PC sound as required. - This monitor apply a VESA Plug and Play Solution. The monitor provides EDID data to the PC system with a DDC protocol. The PC adjusts automatically to use this monitor. - DDC protocol is preset for RGB1 (Analog RGB), RGB2 (DVI, Digital RGB) mode. - If required, adjust the monitor settings for Plug and Play functionally. - If graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB1 INPUT (PC/DTV INPUT) or RGB2 INPUT (DIGITAL RGB INPUT) to display the PC on the monitor. If graphic card on the PC does output analog and digital RGB simultaneously, set the monitor to either RGB1 or RGB2; (the other mode is set to Plug and Play automatically by the monitor.) - The monitor perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. In this case, change the screen scanning rate for the graphic card. PC Setup 1. Turn on the PC and apply power to the Monitor. 2. Turn on the display by pressing the POWER button on the Monitor’s remote control. 3. Use the INPUT SELECT button on the remote control to select the RGB1 or RGB2 input source. 4. Set the resolution output of the PC to SXGA or under (1280 x 1024, 75Hz). Monitor Display Specifications RGB1 Mode Resolution 640x350 720x400 640x480 800x600 Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.468 70.09 37.861 85.08 31.469 70.08 37.927 85.03 31.469 59.94 35.000 DDC Resolution 832x624 Horizontal Vertical Frequency(KHz) Frequency(Hz) 49.725 74.55 DDC 48.363 60.00 56.476 70.06 60.023 75.02 68.677 84.99 66.66 54.348 60.05 37.861 72.80 63.995 70.01 37.500 75.00 67.500 75.00 43.269 85.00 77.487 85.05 45.913 90.03 1152x870 68.681 75.06 1280x960 75.000 75.00 63.981 60.02 79.976 75.02 53.011 100.04 64.062 120.00 35.156 56.25 37.879 60.31 46.875 75.00 53.674 85.06 56.000 90.00 64.016 100.00 1024x768 1152x864 1280x1024 RGB2 Mode Resolution 640x350 720x400 640x480 800x600 Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.468 70.09 37.861 85.08 31.469 70.08 37.927 85.03 31.469 59.94 35.000 66.66 37.861 DDC Resolution 832x624 DDC 48.363 60.00 56.476 70.06 60.023 75.02 68.677 84.99 54.348 60.05 72.80 63.995 70.01 37.500 75.00 67.500 75.00 43.269 85.00 77.487 85.05 35.156 56.25 68.681 75.06 37.879 60.31 60.000 60.00 48.077 72.18 75.000 75.00 63.981 60.02 46.875 75.00 53.674 85.06 1024x768 1152x864 1152x870 1280x960 1280x1024 • Dos mode may not work depending on video card if using a DVI-I cable. 10 Horizontal Vertical Frequency(KHz) Frequency(Hz) 49.725 74.55 Remote Control Key Functions - When using the remote control aim it at the remote control sensor of the Monitor. - There's maybe a defect in consecutive operation of remote control in specified brightness according to this monitor feature. POWER Switches the Monitor on from standby or off to standby. SLEEP Sets the sleep timer. (Refer to p.16) APC Adjusts the factory preset picture according to the room. (Refer to p.14) ARC Changes the picture format. (Refer to p.18) PIP Switches the sub picture on or off. (Refer to p.20) POWER SLEEP INPUT SELECT APC DASP ARC PIP ARC PIP TWIN PICTURE SUB INPUT SWAP MENU VOL MUTE OK PIP ARC Changes the PIP picture format. (Refer to p.20) VOL SUB INPUT Selects the input mode for the sub picture. MUTE Switches the sound on or off. MENU Displays on screen menus one by one. Exits the current menu. Memorizes menu changes. NUMBER buttons OK POWER STOP REW PLAY D /E Selects a menu option. F / G (Volume button) Increases/decreases sound level. Adjusts menu settings. P/STILL FF VCR BUTTONS REC WIN.POSITION Moves the sub picture. WIN.SIZE WIN.POSITION SPLIT ZOOM SPLIT ZOOM Enlarge the screen with regular ration. DASP To select the sound appropriate to your viewing program character: FLAT, SPORTS, CINEMA, MUSIC, or USER (Refer to p.15) TWIN PICTURE (Refer to p.21) SWAP Exchanges main and sub picture images. (Refer to p.20, 21) WIN. SIZE Adjusts the sub picture size. INPUT SELECT Selects: VIDEO, S-VIDEO, RGB1/2 or COMPONENT mode. ZOOM - Controls a LG video cassette recorder. ZOOM + ZOOM-/ZOOM+ Enlarges or reduces the main picture size. Installing Batteries • Open the battery compartment cover on the back side and insert the batteries with correct polarity. • Install two 1.5V alkaline batteries of AAA type. Don’t mix used batteries with new batteries. 11 Monitor overview POWER SLEEP Accessories INPUT SELECT APC DASP ARC PIP ARC PIP TWIN PICTURE SUB INPUT SWAP MENU MUTE VOL OK VOL 1.5V 1.5V Owner’s Manual Alkaline batteries D-sub 15 pin cable Simple Monitor Stand POWER STOP P/STILL REW PLAY FF REC WIN.SIZE WIN.POSITION SPLIT ZOOM ZOOM - BNC-RCA adapter ZOOM + Remote Control Power Cord DVI Cable Monitor Installation Options • The Monitor can be installed in various ways such such as on a wall, or on a desktop etc. • Install this monitor only in a location where adequate ventilation is available. • It is recommended that this product only be used at an altitude of less than 6561 feet (2000m) to get the best quality picture and sound. To Mount on a Wall Wall mount minimum allowable clearances for adequate ventilation. 2 inches 4 inches 4 inches To Install on a Desktop Pedestal mount minimum allowable clearances for adequate ventilation. 2 inches 4 inches 4 inches 4 inches 4 inches 4 inches 2.36 inches Stand Installation 1. Make sure to secure the stand to the display platform using M8 bolts (commercially available) 1 inch (25mm) longer than the thickness of the platform. 3. Use the two (2) bolts provided to attach the stand to the monitor. Tighten each bolt securely in a clockwise direction. Front Rear 26.2 inches (665 mm) 2. Align the holes on the monitor and stand. 12 The monitor weigh 99.2 pounds (45kg) and its thinness makes it unstable. Therefore, unpacking and installation should be performed by two or more persons. Turning on the Monitor - When using the remote control, aim it at its sensor on the Monitor. Turning on the Monitor just after installation 1. Connect power cord correctly. 2. Press the ON/OFF button on the Monitor. At this moment, the Monitor is switched to standby mode. Press the INPUT SELECT button on the Monitor or press the POWER, INPUT SELECT button on the remote control and then the Monitor will switch on. Turning on the Monitor (power cord is still connected) 1. If the Monitor was turned off with the • Press the ON/OFF button on the Monitor ON/OFF button on the Monitor to turn the Monitor on. 2. If the Monitor was turned off with the remote control or the ON/OFF button on the Monitor • Press the ON/OFF button on the Monitor and then press the INPUT SELECT button on the Monitor or press the POWER, INPUT SELECT button on the remote control to turn the Monitor on. Menu Language Selection - The menus can be shown on the screen in the selected language. First select your language. 1. Press the MENU button and then use button to select the SPECIAL menu. VIDEO LANGUAGE 2. Press the G button and then use D / button to select LANGUAGE. AUDIO TIME 3. Press the G button and then use D / E button to select your desired language. From this point on, the on-screen menus will be shown in the language of your choice. KEY LOCK ORBITER WHITE WASH SET ID 한국어 ENGLISH ESPAÑOL PORTUGUÊS FRANÇAIS SPECIAL SCREEN 4. Press the MENU button. TWIN MENU PREV. 13 Video Menu Options APC (Auto Picture Control) - This function adjusts the Monitor to the best picture appearance 1. Press the APC button to select the picture appearance setup option. • Each press of the APC button changes the screen display as shown below. CLEAR SOFT USER • You can also select CLEAR, SOFT or USER in the VIDEO menu. • Picture options CLEAR and SOFT are preset and programmed for good picture quality at the factory and cannot be changed. Adjusting Auto Color Control - To initialize values (reset to default settings), select the NORMAL option. 1. Press the MENU button and then use 2. Press the 3. Press the D button and then use /E D /E D /E button to select the VIDEO menu. button to select ACC . AUDIO button to select the desired color temperature. • Each press of D /E VIDEO TIME button changes the screen display as shown. SPECIAL APC ACC COLOR TEMP. CONTRAST BRIGHTNESS COLOR SHARPNESS TINT 85 60 50 50 NORMAL COOL WARM USER SCREEN NORMAL COOL WARM USER TWIN MENU PREV. Manual Color Temperature Control (User option) - You can adjust red, green, or blue to any color temperature you prefer. 1. Press the MENU button and then use D /E button to select the VIDEO menu. VIDEO 2. Press the G button and then use D /E button to select the COLOR TEMP. option. AUDIO 3. Press the G button and then use D /E button to select a color. TIME 4. Use the F /G button to make appropriate adjustments. 5. Press the MENU button. SPECIAL APC ACC COLOR TEMP. CONTRAST BRIGHTNESS COLOR SHARPNESS TINT 85 60 50 50 SCREEN • The adjustment range of RED, GREEN and BLUE is -10~+10. TWIN MENU PREV. Manual Picture Control (User option) - You can adjust picture contrast, brightness, color, sharpness and tint to the levels you prefer. - PIP settings are not adjustable. 1. Press the MENU button and then use D /E button to select the VIDEO menu. VIDEO AUDIO 2. Press the G button and then use D /E button to select the desired picture option. 3. Press the G button and then use F /G button to make appropriate adjustments. 4. Press the MENU button. TIME SPECIAL SCREEN TWIN 14 APC ACC COLOR TEMP. CONTRAST 85 BRIGHTNESS COLOR SHARPNESS TINT 60 50 50 MENU PREV. RED GREEN BLUE Audio Menu Options DASP (Digital Auto Sound Processing) - This function lets you enjoy the best sound without any special adjustment because the Monitor automatically selects the appropriate sound option based on the program content. 1.Press the DASP button to select the picture appearance setup. FLAT SPORTS CINEMA MUSIC USER • You can also select FLAT, SPORTS, CINEMA, MUSIC, or USER in the AUDIO menu. AVL (Auto Volume Volume Leveler) - This feature maintains an equal volume level; even if you change channels. 1. Press the MENU button and then use 2. Press the 3. Press the button and then use button and then use D /E D /E D /E button to select the AUDIO menu. button to select AVL. button to select ON or OFF. VIDEO DASP AUDIO AVL TIME TREBLE BASS BALANCE 50 50 ON OFF SPECIAL 4. Press the MENU button. SCREEN TWIN MENU PREV. Adjusting Sound (Manual Setting) 1. Press the MENU button and then use D 2. Press the G button and then use /E button to select the AUDIO menu. D /E button to select the desired sound item. F /G button to make appropriate adjustments. VIDEO AUDIO TIME 3. Press the button and then use DASP AVL TREBLE 50 BASS BALANCE 50 SPECIAL 4. Press the MENU button. SCREEN TWIN MENU PREV. 15 Time Menu Options Setting the Clock - If current time setting is erased by a power failure, if TV is unplugged or if the monitor is turned off with the ON/OFF button on the monitor, reset the clock. 1. Press the MENU button and then use D /E button to select the TIME menu. 2. Press the button and then use D /E button to select CLOCK. 3. Press the button and then use D /E button to set the hour. 4. Press the button and then use D /E VIDEO AUDIO TIME CLOCK -- -- OFF TIMER ON TIMER AUTO OFF SPECIAL button to set the minutes. SCREEN 5. Press the MENU button. TWIN MENU PREV. Setting the On/Off On/Off Timer - Timer function operates only if current time has been already set. - Off-Timer function overrides On-Timer function if they are set to the same time. - The monitor must be in standby mode for the On Timer to work. 1. Press the MENU button and then use D /E button to select the TIME menu. VIDEO 2. Press the 3. Press the button and then use D /E button to select OFF TIMER/ON TIMER. button and then use D /E button to select ON. 4. Press the button and then use D /E button to set the hour. 5. Press the button and then use D /E button to set the minutes. AUDIO CLOCK OFF TIMER ON TIMER TIME AUTO OFF OFF ON 12 SPECIAL VOL SCREEN TWIN 6. For only ON TIMER function; Press the volume level. button and then use D /E MENU PREV. button to set 7. Press the MENU button. - To cancel ON/OFF TIMER function Press the D / E button to select OFF in step 3. Auto Off Off - If there is no input signal, the Monitor turns off automatically after 10 minutes. 1. Press the MENU button and then use D /E button to select the TIME menu. 2. Press the G button and then use D /E button to select AUTO OFF. 3. Press the G button and then use D /E button to select ON or OFF. VIDEO AUDIO CLOCK OFF TIMER ON TIMER TIME AUTO OFF SPECIAL 4. Press the MENU button. SCREEN TWIN MENU PREV. Sleep Timer - Sleep timer turns the Monitor off at the preset time. zz - Press the SLEEP button to select the number of minutes. The display --- MIN will appear on the screen, followed by 10, 20, 30, 60, 90, 120, 180 and 240. The timer begins to count down from the number of minutes selected. - When the sleep time you want is displayed on the screen, press the OK button. a. To check the remaining sleep time, press the SLEEP or OK button once. b. To cancel the sleep time, repeatedly press the SLEEP button until the display c. If you turn the monitor off after setting the sleep timer, the setting will be erased. 16 zz --- MIN appears. OFF ON 00 30 Special Menu Options Key Lock - The monitor can be set up so that it can only be used with the remote control. - This feature can be used to prevent unauthorized viewing. 1. Press the MENU button and then use 2. Press the button and then use 3. Press the G button and then use D /E D /E D /E button to select the SPECIAL menu. button to select KEY LOCK. button to select ON or OFF. VIDEO LANGUAGE AUDIO KEY LOCK TIME ORBITER WHITE WASH SET ID ON OFF SPECIAL 4. Press the MENU button. SCREEN With the lock on, the display KEY LOCK appears on the screen if any button on the front panel is pressed while viewing the monitor. TWIN MENU PREV. - This Monitor is programmed to remember which option it was last set to even if you turn the monitor off. - In KEY LOCK ‘ON’, if the monitor is turned off with the remote control, press the INPUT SELECT button on the monitor or POWER, INPUT SELECT on the remote control. - With the KEY LOCK ON, the display ‘ WKEY LOCK’ appears on the screen if any button on the front panel is pressed. Orbiter - Avoid allowing a fixed image to remain on the Monitor's screen for a long period of time. A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost image remaining even when you change the image. - To avoid a permanent image on the screen, the screen will move every 2 minutes: Right → Right → Downside → Downside → Left → Left → Upside → Upside - The Orbiter feature may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. 1. Press the MENU button and then use 2. Press the button and then use 3. Press the G button and then use D /E D /E button to select the SPECIAL menu. button to select ORBITER. button to select ON or OFF. D /E VIDEO AUDIO LANGUAGE KEY LOCK ORBITER TIME ON OFF WHITE WASH SET ID SPECIAL 4. Press the MENU button. SCREEN TWIN MENU PREV. White Wash Wash - White Wash removes permanent images from the screen. - Set White Wash ‘ON’ until fixed image disappears. - A excessive permanent image is impossible to clear with using this function perfectly. 1. Press the MENU button and then use 2. Press the button and then use D /E D /E button to select the SPECIAL menu. button to select WHITE WASH. 3. Press the G button and then use D / E button to select ON or OFF. • When you select ON, the screen changes to white. 4. Press the MENU button. VIDEO AUDIO LANGUAGE KEY LOCK ORBITER TIME WHITE WASH SPECIAL SET ID ON OFF SCREEN TWIN MENU PREV. 17 Screen Menu Options Auto Adjustment - RGB1 (PC) mode only; This function doesn’t work in RGB1-Digital broadcast. - Automatically adjusts picture position and minimizes image shaking. 1. Press the MENU button and then use 2. Press the button and then use D /E D /E button to select the SCREEN menu. VIDEO button to select AUTO CONFIG.. AUDIO 3. Press the G button to run Auto configure. • When AUTO CONFIG. has finished, OK will be shown on screen. • If the position of the image is still not correct, try Auto adjustment again. TIME SPECIAL AUTO CONFIG. ARC ZOOM IN/OUT POSITION MANUAL CONFIG. SCREEN ADJ. RESET SCREEN 4. If picture needs to be adjusted more after Auto adjustment in RGB1(PC), you can adjust the MANUAL CONFIG. TWIN MENU PREV. - Although the image is still not correct, your Monitor is functioning properly but needs further adjustment. - The AUTO CONFIG. and the MANUAL CONFIG can be adjust automatically for RGB 2 mode. Setting Picture Format - You are available to 4:3 and 16:9 in RGB1,RGB2 and COMPONENT(DTV). - You are available to 16:9, 4:3 and ZOOM in VIDEO and S-VIDEO. - If 4:3 is on the screen for a long time, that fixed image may remain visible. 1. Press the ARC button to select a desired picture format. • Each press of ARC button changes the screen display as shown below. • You can also select 4:3, 16:9 or ZOOM in the SCREEN menu. 4:3 16 : 9 ZOOM Split Zoom This is the function to enlarge the screen with regular ration. It’s available to use this function in every input source. with 2-SPLIT ZOOM, you can only move the screen into upside or downside. If a screen is enlarged, a screen can move without selecting section of screen Split Zoom. 1. Press the SPLIT ZOOM button. • Each press of SPLIT ZOOM button changes the screen display as shown below. 2-SPLIT ZOOM 4-SPLIT ZOOM 9-SPLIT ZOOM ▲ ▼ ▲ ▼ ◀▶ ◀▶ ▲ ▼ ◀▶ In case of 9-SPLIT ZOOM: Press the number button to select the section you enlarge. If you choose No.5, the 5 section is enlarged and also can move the enlarged screen with using the button. 9-SPLIT ZOOM 18 ▲ ▼ ◀▶ In case of choosing the No.5 D /E /F /G The 5 section is changed to a full screen. TO SET Screen Position - This function works in the following mode: RGB1-PC, RGB1-DTV 480p,720p,1080i, COMPONENT 480p,720p,1080i. 1. Press the MENU button and then use D /E button to select the SCREEN menu. 2. Press the button and then use D /E 3. Press the button and then use D /E /F /G button to select POSITION. button to adjust the position. VIDEO AUDIO AUTO CONFIG. ARC ZOOM IN/OUT TIME POSITION SPECIAL 4. Press the MENU button. ▲ ◀ ▶ ▼ MANUAL CONFIG. SCREEN ADJ. RESET SCREEN TWIN MENU PREV. Manual Configure (RGB1 [PC] mode only) - If the picture isn’t clear after auto adjustment and especially if characters are still jittery, adjust the picture phase manually. - To correct the screen size, adjust CLOCK. 1. Press the MENU button and then use D /E 2. Press the G button and then use D /E button to select MANUAL CONFIG.. 3. Press the G button and then use D /E button to to select PHASE or CLOCK. button to select the SCREEN menu. VIDEO 4. Use the F /G button to make appropriate adjustments. • The adjustment range of PHASE is 0 ~ 31. • The adjustment range of CLOCK is -50 ~ +50. AUDIO TIME SPECIAL SCREEN TWIN AUTO CONFIG. ARC ZOOM IN/OUT POSITION MANUAL CONFIG.G PHASE SCREEN ADJ. RESET CLOCK MENU PREV. 5. Press the MENU button. Screen Adjustments (VIDEO, S-VIDEO and COMPONENT 480i mode only) - Use this function to correct jittering or picture instability while viewing a video tape. button to select the SCREEN menu. 1. Press the MENU button and then use D /E 2. Press the G button and then use D /E button to select SCREEN ADJ.. 3. Press the G button and then use D /E button to to select TV or VCR. • Select the VCR option if watching a VCR. • Select the TV option for other equipment.(Except VCR) VIDEO AUDIO TIME SPECIAL SCREEN TWIN 4. Press the MENU button. AUTO CONFIG. ARC ZOOM IN/OUT POSITION MANUAL CONFIG. SCREEN ADJ. TV VCR RESET MENU PREV. Initializing (Reset to original factory value) - This function operates in every mode. - To initialize the adjusted value 1. Press the MENU button and then use D /E 2. Press the G button and then use button to select RESET. D /E button to select the SCREEN menu. 3. Press the G button. VIDEO AUDIO TIME SPECIAL • You can initialize ZOOM IN/OUT, POSITION, SPLIT ZOOM, PIP size, PIP position and sub picture size for twin picture. SCREEN TWIN AUTO CONFIG. ARC ZOOM IN/OUT POSITION MANUAL CONFIG. SCREEN ADJ. RESET TO SET MENU PREV. 19 PIP (Picture-in-Picture) Feature - PIP lets you view 2 different inputs (sources) on your monitor screen at the same time. One source will be large, and the other source will show a smaller inset image. - When you select PC or DTV for main picture in PIP, you can watch VIDEO, S-VIDEO or COMPONENT 480i for sub picture. Watching PIP PIP Size Press the PIP button to show the sub picture. • Press the PIP button again to turn PIP off. Press the WIN.SIZE button and then use change the sub picture size. F /G button to COMPONENT VIDEO 10 : 30 WIN.SIZE ◀ PIP Aspect Ratio ▶ Swapping the PIP Press the PIP ARC button. • The sub picture appears as below. Press the SWAP button to exchange the main and sub pictures. VIDEO COMPONENT COMPONENT VIDEO 10 : 30 10 : 30 16 : 9 4: 3 Main Picture Sub Picture Selecting a Input Signal Source for the PIP Moving the PIP Press the WIN.POSITION button. Press the D / E / F / G button repeatedly until desired position is achieved. The sub picture moves up/down/left/right. Press the SUB INPUT button to select the input source for the sub picture. COMPONENT VIDEO 10 : 30 WIN.POSITION ▲ ◀ ▶ ▼ Main Picture Size Adjustment Press the ZOOM+/ZOOM- button to enlarge or reduce the main picture size when viewing the PIP. ZOOM 100 % • In RGB1 and RGB2 for main picture, you can select COMPONENT 480i, VIDEO and S-VIDEO for sub picture. • In VIDEO and S-VIDEO for main picture, you can select COMPONENT 480p/720p/1080i, RGB1 and RGB2 for sub picture. • In COMPONENT 480p/720p/1080i for main picture, you can select VIDEO and S-VIDEO for sub picture. • In COMPONENT 480i for main picture, you can select RGB1 and RGB2 for sub picture. Main Picture Position Adjustment Adjust the main picture position with the buttons in enlarged main picture mode. ZOOM 100 % ▲ ◀ 20 ▼ ▲ ▶ ◀ ▼ ▶ D /E /F /G Twin Picture Main Picture Size Adjustment Use the TWIN PICTURE button. • Each press of the TWIN PICTURE button cycles through the screen displays shown below. DW 1 DW 2 Sub Picture Size Adjustment Selecting a Source for the Twin Picture Use the WIN.SIZE button. • Use the F / G button to adjust the sub picture size. • Using WIN.SIZE function in Twin Picture mode, main and sub picture are adjusted simultaneously. Using WIN.SIZE function in PIP mode, sub picture is adjusted. • WIN.POSITION is not functional in twin picture mode. Use the SUB INPUT button to select the input source for the sub picture. COMPONENT VIDEO 10 : 30 • Using sources RGB1 or RGB2 for main picture, you can select COMPONENT 480i, VIDEO, or S-VIDEO for sub picture. • Using sources VIDEO or S-VIDEO for main picture, you can select COMPONENT 480p/720p/1080i, RGB1, or RGB2 for sub picture. • Using sources COMPONENT 480p/720p/1080i for main picture, you can select VIDEO, or S-VIDEO for sub picture. • Using sources COMPONENT 480i for main picture, you can select RGB1, or RGB2 for sub picture. WIN.SIZE ◀ Off ▶ Swapping the Twin Picture Use the SWAP button to switch the main and sub pictures in twin picture mode. COMPONENT VIDEO 10 : 30 VIDEO COMPONENT 10 : 30 21 External Control Device Setup - Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally. - Connect the serial port of the control device to the RS-232C jack on the Monitor back panel. - RS-232C connection cables are not supplied with the Monitor. Type of connector; D-Sub 9-pin male No. Pin name No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection RS-232C configurations 3-wire configuration (Not standard) 7-wire configuration (Standard RS-232C cable) RXD TXD GND DTR DSR RTS CTS PC PDP D-Sub 9 D-Sub 9 TXD RXD GND DSR DTR CTS RTS RXD TXD GND DTR DSR RTS CTS PC PDP D-Sub 9 D-Sub 9 TXD RXD GND DTR DSR RTS CTS Control line Set ID - Use this function to specify a monitor ID number. - Refer to ‘Real Data Mapping 1’. See page 24. 1. Press the MENU button and then use the 2. Press the button and then use D /E 3. Press the G button and then use monitor ID number. F /G D /E button to select the SPECIAL menu. button to select SET ID. button to adjust SET ID to choose the desired VIDEO AUDIO TIME SPECIAL LANGUAGE KEY LOCK ORBITER WHITE WASH SET ID SCREEN • The adjustment range of SET ID is 1 ~ 99. TWIN Communication Parameters • Baud rate : 115200 bps (UART) • Data length : 8 bits • Parity : None 22 • Stop bit : 1 bit • Communication code : ASCII code MENU PREV. OK Acknowledgement Command Reference List COMMAND 1 COMMAND 2 DATA (Hexadecimal) 01. Power 02. Input Select 03. Aspect Ratio 04. Screen Mute 05. Volume Mute 06. Volume Control 07. Contrast 08. Brightness 09. Color 10. Tint 11. Sharpness 12. OSD select 13. Remote control lock mode 14. PIP/Twin 15. PIP size 16. PIP position 17. Treble 18. Bass 19. Balance 20. Color temperature 21. Red adjustment 22. Green adjustment 23. Blue adjustment 24. PIP input source 25. Orbiter 26. White Wash 27. Orbiter Time Setting 28. Orbiter Pixel Setting 0~1 0~4 0~2 0~1 0~1 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0~1 0~1 0~3 0~1 0~3 0 ~ 64 0 ~ 64 0 ~ 64 0~3 0 ~ 64 0 ~ 64 0 ~ 64 0~4 0~1 0~1 1 ~ FE 0 ~9 * When setting the 25 ~ 28, a menu doesn’t display on screen. [Command2][ ][Set ID][ ][OK][Data][x] * The Monitor transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer. Error Acknowledgement [Command2][ ][Set ID][ ][NG][x] * The Monitor transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors. 01. Power (Command:a) G To control Power On/Off of the Monitor. Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Power Off 1 : Power On Acknowledgement [a][ ][Set ID][ ][OK][Data][x] Data 0 : Power Off 1 : Power On G To show Power On/Off. Transmission [k][a][ ][Set ID][ ][FF][Cr] Data 0 : Power Off 1 : Power On Acknowledgement [a][ ][Set ID][ ][OK][Data][x] Data 0 : Power Off 1 : Power On * In like manner, if other functions transmit ‘FF’ data based on this format, Acknowledgement data feed back presents status about each function. Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] * [Command 1] * [Command 2] * [Set ID] * [DATA] * [Cr] * [ ] : k : To control PDP set. : You can adjust the set ID to choose desired monitor ID number in special menu. See previous page. Adjustment range is 1 ~ 99. When selecting Set ID ‘0’, every connected PDP set is controlled. : To transmit command data. Transmit ‘FF’ data to read status of command. : Carriage Return ASCII code ‘0x0D’ : ASCII code ‘space (0x20)’ 02. Input Select (Command:b) (Main Picture Input) G To select input source for the Monitor. You can also select an input source using the INPUT SELECT button on the Monitor's remote control. Transmission [k][b][ ][Set ID][ ][Data][Cr] Data 0 : RGB 1 1 : COMPONENT 2 : VIDEO 3 : S-VIDEO 4 : RGB 2 Acknowledgement [b][ ][Set ID][ ][OK][Data][x] Data 0 : RGB 1 1 : COMPONENT 2 : VIDEO 3 : S-VIDEO 4 : RGB 2 23 03. Aspect Ratio (Command:c) (Main picture format) 07. Contrast (Command:g) G To adjust the screen format. You can also adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Special menu. Transmission G To adjust screen contrast. You can also adjust contrast in the Video menu. [k][c][ ][Set ID][ ][Data][Cr] Data 0 : Wide screen (16:9) 1 : Normal screen (4:3) 2 : Full screen (Zoom) Acknowledgement [c][ ][Set ID][ ][OK][Data][x] Data 0 : Wide screen (16:9) 1 : Normal screen (4:3) 2 : Full screen (Zoom) Transmission [k][g][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 * Refer to ‘Real data mapping1’ as shown below. Acknowledgement [g][ ][Set ID][ ][OK][Data][x] Data Min : 0 ~ Max : 64 08. Brightness (Command:h) G To adjust screen brightness. You can also adjust brightness in the Video menu. * Using the PC input, you select either 16:9 or 4:3 screen aspect ratio. Transmission 04. Screen Mute (Command:d) Data Min : 0 ~ Max : 64 * Refer to ‘Real data mapping1’ as shown below. G To select screen mute on/off. Transmission [k][d][ ][Set ID][ ][Data][Cr] Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off) Acknowledgement [d][ ][Set ID][ ][OK][Data][x] Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off) 05. Volume Mute (Command:e) G To control volume mute on/off. You can also adjust mute using the MUTE button on remote control. Transmission [k][e][ ][Set ID][ ][Data][Cr] Data 0 : Volume mute on (Volume off) 1 : Volume mute off (Volume on) Acknowledgement [e][ ][Set ID][ ][OK][Data][x] Data 0 : Volume mute on (Volume off) 1 : Volume mute off (Volume on) 06. Volume Control (Command:f) G To adjust volume. You can also adjust volume with the volume buttons on remote control. Transmission [k][h][ ][Set ID][ ][Data][Cr] Acknowledgement [h][ ][Set ID][ ][OK][Data][x] Data Min : 0 ~ Max : 64 09. Color (Command:i) G To adjust the screen color. You can also adjust color in the Video menu. Transmission [k][i][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 * Refer to ‘Real data mapping1’ as shown below. Acknowledgement [i][ ][Set ID][ ][OK][Data][x] Data Min : 0 ~ Max : 64 10. Tint (Command:j) G To adjust the screen tint. You can also adjust tint in the Video menu. Transmission [k][j][ ][Set ID][ ][Data][Cr] Data Red : 0 ~ Green : 64 * Refer to ‘Real data mapping1’ as shown below. Acknowledgement [j][ ][Set ID][ ][OK][Data][x] Data Red : 0 ~ Green : 64 * Real data mapping 1 0 : Step 0 [k][f][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 * Refer to ‘Real data mapping1’ as shown right. Acknowledgement [f][ ][Set ID][ ][OK][Data][x] Data Min : 0 ~ Max : 64 24 A : Step 10 (SET ID 10) F : Step 15 (SET ID 15) 10 : Step 16 (SET ID 16) * Real data mapping 2 0 : -10 5 : -9 A : -8 2D: -1 32: 0 37: +1 64 : Step 100 5F: +9 64: +10 11. Sharpness (Command:k) 16. PIP Position (Command:q) G To adjust the screen sharpness. You can also adjust sharpness in the Video menu. Transmission G To select sub picture position for PIP. You can also adjust the sub picture position using WIN.POSITION on the remote control or in the Special menu. [k][k][ ][Set ID][ ][Data][Cr] Transmission Data Min : 0 ~ Max : 64 * Refer to ‘Real data mapping1’. See page 24. Acknowledgement [k][q][ ][Set ID][ ][Data][Cr] [k][ ][Set ID][ ][OK][Data][x] Data 0 Data Min : 0 ~ Max : 64 Acknowledgement 12. OSD Select (Command:l) [q][ ][Set ID][ ][OK][Data][x] G To select OSD (On Screen Display) on/off. Data 0 Transmission [k][l][ ][Set ID][ ][Data][Cr] Data 0 : OSD off G To adjust treble. You can also adjust treble in the Audio menu. 1 : OSD on 13. Remote Control Lock Mode (Command:m) G To lock the front panel controls on the monitor and remote control. Transmission [k][m][ ][Set ID][ ][Data][Cr] 1 : Lock on Transmission [k][r][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 * Refer to ‘Real data mapping1’. See page 24. Acknowledgement [r][ ][Set ID][ ][OK][Data][x] Data Min : 0 ~ Max : 64 Acknowledgement [m][ ][Set ID][ ][OK][Data][x] Data 0 : Lock off Right down on screen Left down on screen Left up on screen Right up on screen 17. Treble (Command:r) [l][ ][Set ID][ ][OK][Data][x] Data 0 : Lock off Right down on screen Left down on screen Left up on screen Right up on screen 1 : OSD on Acknowledgement Data 0 : OSD off 1 : Lock on 18. Bass (Command:s) * If you’re not using the remote control, use this mode. When main power is on/off, remote control lock is released. G To adjust bass. You can also adjust bass in the Audio menu. 14. PIP / Twin (Command:n) Transmission G To control the PIP (Picture In picture). You can also control the PIP/TWIN using the PIP or Twin picture button on the remote control or in the Special menu. Transmission [k][n][ ][Set ID][ ][Data][Cr] Data 0 : PIP/DW off 1 : PIP [k][s][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 * Refer to ‘Real data mapping1’. See page 24. Acknowledgement [s][ ][Set ID][ ][OK][Data][x] 2 : DW1 3 : DW2 Data Min : 0 ~ Max : 64 Acknowledgement 19. Balance (Command:t) [n][ ][Set ID][ ][OK][Data][x] Data 0 : PIP/DW off 1 : PIP 2 : DW1 3 : DW2 15. PIP Size (Command:o) G To select the PIP picture format. You can also select the PIP picture format using WIN.SIZE on the remote control. Transmission [k][o][ ][Set ID][ ][Data][Cr] Data 0 : 4:3 [k][t][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 * Refer to ‘Real data mapping1’. See page 24. [t][ ][Set ID][ ][OK][Data][x] Data Min : 0 ~ Max : 64 [o][ ][Set ID][ ][OK][Data][x] 4:3 Transmission Acknowledgement 1 : 16:9 Acknowledgement Data 0 : G To adjust balance. You can also adjust balance in the Audio menu. 1 : 16:9 25 20. Color Temperature (Command:u) 25. Orbiter (Command:p) G To adjust color temperature. You can also adjust ACC in the Video menu. G To control the orbiter function on/off. Transmission Transmission [k][u][ ][Set ID][ ][Data][Cr] [j][p][ ][Set ID][ ][Data][Cr] Data 0: Normal 1: Cool 2: Warm 3: User Data 0 : Orbiter off 1 : Orbiter on Acknowledgement 2: Warm 3: User Data 0 : Orbiter off 1 : Orbiter on Acknowledgement [u][ ][Set ID][ ][OK][Data][x] Data 0: Normal 1: Cool [p][ ][Set ID][ ][OK][Data][x] 21. Red Adjustment (Command:v) G To adjust red in color temperature. 26. White Wash (Command:q) Transmission G To control the white wash function on/off. [k][v][ ][Set ID][ ][Data][Cr] Transmission Data Min : 0 ~ Max : 64 * Refer to ‘Real data mapping 2’. See page 24. [j][q][ ][Set ID][ ][Data][Cr] [v][ ][Set ID][ ][OK][Data][x] Data 0 : White Wash off 1 : White Wash on Acknowledgement Data Min : 0 ~ Max : 64 [q][ ][Set ID][ ][OK][Data][x] 22. Green Adjustment (Command:w) Data 0 : White Wash off 1 : White Wash on Acknowledgement G To adjust green in color temperature. Transmission [k][w][ ][Set ID][ ][Data][Cr] 27. Orbiter Time Setting (Command:r) Data Min : 0 ~ Max : 64 * Refer to ‘Real data mapping 2’. See page 24. Acknowledgement G To adjust orbiter operation time term. Transmission [j][r][ ][Set ID][ ][Data][Cr] [w][ ][Set ID][ ][OK][Data][x] Data Min : 0 ~ Max : 64 Data Min : 1 ~ Max : FE * Refer to ‘Real data mapping1’. See page 24. 23. Blue Adjustment (Command:$) Acknowledgement G To adjust blue in color temperature. [r][ ][Set ID][ ][OK][Data][x] Transmission Data Min : 1 ~ Max : FE [k][$][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 * Refer to ‘Real data mapping 2’. See page 24. Acknowledgement 28. Orbiter Pixel Setting (Command:s) [$][ ][Set ID][ ][OK][Data][x] G To adjust pixel number in orbiter function. Data Min : 0 ~ Max : 64 Transmission 24. PIP Input Select (Command:y) [j][s][ ][Set ID][ ][Data][Cr] G To select input source for sub picture in PIP mode. Data Min : 0 ~ Max : 9 * Refer to ‘Real data mapping1’. See page 24. Transmission Acknowledgement [k][y][ ][Set ID][ ][Data][Cr] Data 0 : RGB1 2 : VIDEO 1 : COMPONENT 3 : S-VIDEO [s][ ][Set ID][ ][OK][Data][x] 4 : RGB2 Acknowledgement [y][ ][Set ID][ ][OK][Data][x] Data 0 : RGB1 2 : VIDEO 26 1 : COMPONENT 3 : S-VIDEO 4 : RGB2 Data Min : 0 ~ Max : 9 IR Code (NEC Format) How to connect G Connect your wired remote control to the Remote port on the Monitor. Set the CONTROL LOCK to ‘ON’ on the Monitor back panel to operate Monitor with wired remote control. Remote Control IR Code (NEC Format) G Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz TC Carrier frequency FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3 T1 G Configuration of frame • 1st frame Lead code Low custom code High custom code Data code Data code C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 • Repeat frame Repeat code Tf G Lead code 9 ms 4.5 ms 0.55 ms G Repeat code 9 ms 2.25 ms G Bit description • Bit “0” • Bit “1” 0.56 ms 0.56 ms 1.12 ms 2.24 ms G Frame interval : Tf The waveform is transmitted as long as a key is depressed. Tf Tf Tf=108ms @455KHz 27 Code (Hexa) 00H 01H 02H 03H 08H C4H C5H 09H 10H 11H 12H 13H 14H 15H 16H 17H 18H 19H 0BH 98H C6H 5AH 51H BFH 0EH 44H 43H 52H 4DH 60H 61H 63H 64H 6BH 40H 41H 69H 6AH 7BH 79H 76H 77H AFH 28 Function UP (D) DOWN (E) VOL+ (G) VOL- (F) POWER On/Off POWER ON POWER OFF MUTE Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6 Number Key 7 Number Key 8 Number Key 9 AII INPUT SELECT RGB 1 RGB 2 (DVI input) VIDEO S-VIDEO COMPONENT SLEEP OK (Á) MENU DASP APC PIP PIP INPUT SWAP PIP ARC TWIN PICTURE ZOOM + ZOOM Window Size Window Position Split Zoom ARC ARC (4:3) ARC (16:9) ARC (ZOOM) Note R/C Button R/C Button R/C Button R/C Button R/C Button (Power On/Off) Discrete IR Code (Only Power On) Discrete IR Code (Only Power Off) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button(RGB1/RGB2/Comp/VIDEO/S-VIDEO) Discrete IR Code (Input RGB1 Selection) Discrete (Input RGB2 Selection) Discrete (Input VIDEO Selection) Discrete (Input S-VIDEO Selection) Discrete (Input COMPONENT Selection) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button (PIP/TWIN Exchange) R/C Button (4:3/16:9) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button(4:3/16:9/Zoom Mode Selection) Discrete (Only 4:3 mode) Discrete (Only 16:9 mode) Discrete (Only ZOOM mode) Maintenance - Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new Monitor. Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen 1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen. 2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your Monitor. Cleaning the Cabinet To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth. Extended Absence If you leave your Monitor dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges. 29 Troubleshooting Checklist • Check whether the Monitor is turned on. No picture & No sound • Power cord inserted into wall outlet? • Plug another product’s power cord into the wall outlet where the Monitor’s power cord was plugged in. Picture OK & No sound • Press the VOLUME (G) button. • Sound muted? Press MUTE button. • Check to see if there is any object between the Plasma Display and the remote control causing obstruction. The remote control doesn’t work • Check to see if the batteries are installed with the correct polarities. (Refer to p.11) • Install new batteries. (Refer to p.11) • Select COLOR in the VIDEO menu and press the VOLUME (G) button. (Refer to p.14) No or Poor color or Poor picture • Keep a certain distance between the Monitor and the VCR. • Activate any function to restore the brightness of the picture. (If still picture is on the screen for more than 5 minutes, the screen gets dark.) No output from one of the speakers Strange sound from the Monitor 30 • Adjust BALANCE in the AUDIO menu. (Refer to p.15) • Typical sound due to normal Monitor operation, Monitor is not faulty. Product Specifications MODEL MU-50PZ40/A/B/K/R/S, MU-50PZ41/A/B/K/R/S Width (inches / mm) 48.2 / 1223 Height (inches / mm) 28.9 / 734 Depth (inches / mm) 4.1 / 105 Weight (pounds / kg) 99.2 / 45 Power requirement AC120V, 60Hz Resolution 1366 x 768 (Dot) Color 16,770,000 (256 steps of each R, G and B) Operating Temperature Range 32 ~ 104°F (0 ~ 40°C) Operating Humidity Range Less than 80% • The specifications shown above may be changed without notice for quality improvement. 31
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 1997:08:16 09:56:21 Producer : Acrobat Distiller 4.0 for Macintosh Creator : QuarkXPressª3.3E: LaserWriter 8 Z1-8.7.1 Author : PSY Title : 352A(LG) Modify Date : 1997:08:16 12:52:55+09:00 Page Count : 31EXIF Metadata provided by EXIF.tools