Lodar 111 111-4 User Manual TI 111 01E

Lodar LTD 111-4 TI 111 01E

Contents

User instructions

TI111RX.01EWiring Instructions for TI-111 Series 2 & 4 Function, FET Receivers.miniOUTDOWNINUPLEFT RIGHTwww.lodar.comF1 F2F3 F42or Disconnect BatteryIDENTIFY POWERCONNECTION POINTAND ISOLATE SUPPLYFuseRemove fuseVehicle batteries contain gasses which are flammable and explosive. Wear eye protection and do not lean over battery while disconnecting. Do not wear metal jewellery.!WARNING1. The Receiver is designed to carry a maximum of 15 Amps. That is, for example,15 Amps through one output or 5 Amps each through 3 outputs.2. Master Output. This can be configured to Continuous or Parallel operation, see overleaf for details.3. If Receiver outputs are connected in parallel with an external switching device (wired remote) the Receiver will instantly switch off when the wired remote is operated4. Lodar Receivers have an isolation switch for safety, to allow for registering a MUST replacement Transmitter.5. Safety Feature. Both the Transmitter and the Receiver will “time out” after 30 minutes of inactivity. This can be altered, ask your dealer.1!BEFORE YOU STARTCONNECTWIRES4TransmitterFunction Convention5or re-connect BatteryACTIVATE THE RECEIVER SUPPLYFuseReplace fusePress the Transmitter buttonRESETto activate the system, and carefully test each function for correct operation.7TEST6CONNECT TRANSMITTER BATTERYBatteries generally have to be disconnected when shipping.12/24 Volts DC NominalPositive SupplyREDNegative BLACKGREENYELLOWBROWNBLUEWHITEOutput Function 1Output Function 2Output Function 3Output Function 4Output Function MasterWire used forWire ColourNot PresentNot PresentNot PresentNot UsedNot Used9200RXand 9300RX9202RXand 9302RX9204RXand 9304RXMake notes about theconnections made in the boxes belowWhat is the MASTER Output for ?It is used to operate the pump of an electro-hydraulicpower pack or maybe a clutch pump. It can also be used for powering a dump valve, master valve etc.It can be configured to work continuously, that is ONwhen SET is pressed and OFF when STOP is pressed; or in parallel with any output, that is, it isactive only a function is operated. If it is needed with certain functions only, this can easily be configured.3Secure using 5mm (3/16") bolts (not supplied)through the 4 mounting feetTAKE TIME TO LOCATE THE BEST POSITIONIf necessary, power the Receiver and move it aroundthe vehicle until the required performance is achieved.Operate the Transmitter and observe the Receiverinternal LED’s.Mount as HIGH as possibleAVOID surfaces with HEAVY VIBRATIONAVOID DIRECT SPRAY from wheelsIn a HOT CLIMATE fit in a SHADED positionCable gland should face DOWN or BACKReceiver 9204RX and 9304RX shown,Waterproof to IP67, complete with 3 metres (10 ft) cablesCAUTIONMOUNT RECEIVER!Shown with optional Keypad92 02/4 RX & 93 02/4 RXhave 7 core cable92 00 RX & 93 00 RXhave 4 core cableSTOP POSITIVENEGATIVEwww.lodar.com9000F1 F2F3 F4
S-, S+ ConnectionsFor Safety Solenoid etc.Part No. 9820 or 9821STOP and -, when connected togetherwill cause the Receiver to power downRS232 connectionfor programming andspecial featuresSMA connector forExternal Aerial AntennaPart No. 9861, 9862, 9863 or 9869Supply 12/24 V DC40 Volts ABSOLUTE MAXOutputs sockets+, -, F1& F2F3, F4, and Master.The Receiver is designedto handle 15 Amps, current draw in excess of this willtrigger a system shut down.Any output can handlethis maximum current.Standard (Internal) AntennaconnectionConnection DetailLk1, when bridgedcauses the MasterOutput to beParallelLK2, when bridgedcauses the MasterOutput to beContinuousJumper MUST be fitted to only ONE linkPOWER DOWN RECEIVER BEFORE MAKING CHANGESLED marked “5V”Indicates power supply for controlcircuits is OK LED’s marked“F1 - F2 - F3 - F4 and M”When ON indicate anoutput to that functionLED marked “FAULT”Indicates an overload is present; the System cannot be RESET until overload is removed.This LED blinks for 20 seconds when the Receiver is initially powered. A replacement Transmitter has to be registered during this 20 second period.LED marked “SET”Indicates system is activeVOLTAGEWorking Range12 Volts to 36 Volts DCLimits8 Volts minimum to 40 Volts absolute max.Component DetailYour product is marked with this symbol. It means that used electrical and electronic products should not be mixed with general household waste. There is a separate collection system for these products.In the EEC - Please contact your National Distributor (see www.lodar.com for this information) who will inform you about the take-back of the product. You might be charged for the costs arising from the take-back and recycling. Small products might be taken back by your local collection facilities.Outside the EEC - If you wish to discard this product please contact your local authorities and ask for the correct method of disposalLodar60 Sandwell Street,Walsall, WS1 3EB.England www.lodar.comemail: sales@lodar.comTel: +44 (0)1922 613633Fax: +44 (0)1922 626991CONTACT INFORMATION92004RX.01E

Navigation menu