Lutron Electronics 0105 PowPak Dimming Module Relay Control User Manual Manual PWM

Download:
Mirror Download [FCC.gov]
Document ID	2186920
Application ID	qgTcOcQxjaYF2vWGjV5SCQ==
Document Description	Manual PWM
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	262.41kB (3280096 bits)
Date Submitted	2014-02-11 00:00:00
Date Available	2014-02-11 00:00:00
Creation Date	2014-01-22 13:15:52
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2014-02-10 13:53:05
Document Title	PowPak 0-10 V/PWM Dimming Module Japan Installation Sheet Part #041434a
Document Creator	Adobe InDesign CS6 (Windows)

Required Components
PowPak® | Installation
Dimming Module with PWM / 0 – 10 V
041434
Rev. A
01/2014
Part of the Energi TriPak® Family
LMJ-5PWM-DV-B
Load Status LED
•
•
•
•
•
WARNING
Lower
Shock Hazard. May result in serious injury or death.
Turn off power at circuit breaker before installing the unit.
Test
Radio Powr SavrTM Occupancy/Vacancy Sensor
(6 maximum)
Mount, Wire, and Install PWM/0 – 10 VDevices and Lighting Fixtures
Radio Powr SavrTM Daylight Sensor
(9 maximum)
(1 maximum)
Switches up to 5 A total. May be pre-installed in light fixtu e.
Control line current - PWM: 150 mA max; 0-10 V-: 60 mA
Install PowPak® Dimming Module
Wiring for 100 V~ applications:
Junction Box
Suggested Installation Location:
Hot (Black)
Install in center of room.
Switched Hot (Yellow)
This ensures proper RF coverage of area.
Neutral (White)
If installing unit inside a junction box please
see Lutron P/N 369674.
		 For more information: www.lutron.com/powpakrelay
Neutral (White)
HOT
Violet
–
Gray
–
Class 2
MAINS
NEU
Switched Hot
To fixtu es
21 mm Knockout Opening
Conduit Nut
A PowPak® Dimming Module can be installed in a junction box or
Sample ballast shown
All Wireless
Transmitters
must be
installed within
7 m of the
PowPak® Dimming Module.
Pico® Wireless Control
Fixture Earth
Neutral
marshalling box using the conduit nut (provided) or with mounting
screws (not provided). Please consult local and national electric
codes for proper installation.
B Once installed, energize the PowPak® Dimming Module.
C Use the Toggle button “ ” to toggle between high-end and OFF
to verify ballast wiring.
D Use the Raise “ ” and Lower “ ” buttons to verify control wiring.
To additional fixtu es
10 m
Pico®
Wireless Control
Consult third-party device installation guide
Turn off power at circuit breaker before installing unit.
A Connect mains wiring (switched hot, neutral) to each fixtu e.
B Connect low‑voltage control (+ and – ) to each fixtu e.
Radio Powr SavrTM
Occupancy Sensor
PowPak®
Dimming
Module
Cal.
Link
Start Here
PowPak® Dimming Module
Install in center of room
to maximize RF coverage.
English
Consult third-party fixtu es installation guide for fixtu e-specific wiring.
PowPak® Dimming Module with
PWM / 0 – 10 V- (1 maximum)
Green/Yellow
7 m max
At least one PWM or 0 – 10 V- Fluorescent Ballast or LED Driver
Toggle
PWM Control: 12 V- 150 mA
0 – 10 V- Control: 10 V- 60 mA
•
•
At least one Wireless Transmitter
Raise
120 / 277 V~ 50 / 60 Hz 5 A
Important Notes: Please read before installing.
For installation by a qualified electrician in acco dance with all
local and national electrical codes.
Note: Use copper conductors only.
Check to see that the device type and rating is suitable for the
application.
DO NOT install if product has any visible damage.
If moisture or condensation is evident, allow the product to dry
completely before installation.
Operate between 0 °C and 40 °C ambient.
0% to 90% humidity, non-condensing.
For indoor use only.
Need Help? visit www.lutron.com.jp or call Lutron® Technical Support at 0120.083.417
For each system, ensure that you have:
One PowPak® PWM Dimming Module
–
Associate Wireless Transmitters to PowPak®
Dimming Module
Install Wireless
Transmitters
Before beginning this step, make sure that
there are no other PowPak® modules being set
up within the same building. It is possible that
wireless transmitters from other systems can
be incorrectly associated to this module.
A On PowPak® Dimming Module, hold Toggle
button “ ” for 6 seconds until lights flash
The Load Status LED will begin flashing twice
per second.
B Hold the indicated button on each transmitter
for 6 seconds. Lights will flash to show that
wireless transmitters have been associated.
12 m
Control line to fixtu es*
* Use 0.75 mm2 to 1.5 mm2 solid
wire only
Note: Please consult individual component
installation guides for information.
Wiring for 200 V~ applications:
Junction Box
(requires a 2-pole input breaker)
Hot 1 (Black)
Switched Hot (Yellow)
Hot 2 (White)
Hot 2 (White)
To fixtu es
21 mm Knockout Opening
Conduit Nut
Link
Test
Default Functionality
Occupied: All lights 100%.
Unoccupied: All lights off.
Daylight Sensor will control all wired fixtu es equally.
A Set lights in room to desired light level.
B Press and hold “Cal.” for
Daylight Sensor
All lights dim in response to daylight.
Cal.
Link
6 seconds.
C Exit room for 5 minutes to
complete calibration.
Note: When calibration has
completed, all lights will flash
and begin daylighting.
Test
Daylight Override
Pressing the raise button on an
associated Pico® Wireless Control will
temporarily override daylighting.
Daylight Re-Enable
Cal.
Link
Test
Multiple Daylight Rows
Test
Cal.
Link
Calibrate Daylight Sensor
Occupancy Sensors
(OPTIONAL)
Wireless Controls
On
All lights 100%
Favorite All lights 50%
Off
All lights off
C	On PowPak® Dimming Module, hold Toggle button “ ” for 6 seconds to save
association. Lights will flash and LED will quickly blink for 2 seconds.
For every row of daylighting a separate PowPakR
Dimming Module must be used. For detailed setup
refer to the tuning section of the Radio Powr SavrT
Daylight Sensor installation guide.
• Select the PowPakR Dimming Module that you
want to adjust by pressing the toggle button
–
Daylighting will be re-enabled when one
of the following occurs:
• Two hours have passed since the
override.*
• ON, OFF, or Favorite button has been
pressed on a Pico® Wireless Control.
• All associated Occupancy Sensors have
reported unoccupied.
* Each time a daylighting override occurs,
the two-hour timer is reset.
Control line to fixtu es*
* Use 0.75 mm2 to 1.5 mm2 solid
wire only
Supplied Terminal Information
Strip Length: 9 mm
Torque: 2 N•m
9 mm
PowPak® | Programming
•
•
•
•
ALL PROGRAMMING IS OPTIONAL
Programming is not required for default functionality
Set a favorite light level
Set high-end and low-end trim for all fixtu es
Set occupancy levels
Set minimum light level for all fixtures
Please consult individual component installation and
programming guides for more details.
FCC Information (LMJ- and ULMJ- only)
This device complies with part 15 of the FCC Rules and Industry Canada license-exempt
RSS standard(s). Operation is subject to the following two conditions: (1) This device
may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation. Modifications not expressly approved by
Lutron Electronics Co., Inc. could void the user’s authority to operate this equipment. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Limited Warranty
(Lutron Asuka Company, Ltd., will, at its option, repair or replace any unit that
is defective in materials or manufacture within one year after purchase. For
warranty service, return unit to place of purchase, or mail to Lutron Asuka
Company, Ltd., No. 16 Kowa Building, 4F 1-9-20, Akasaka, Minato-ku Tokyo
107-0052 Japan, postage pre-paid, or telephone Lutron Asuka Company, Ltd.,
at 03.5575.8411.
This warranty is the sole express warranty, and the implied warranty of
merchantability, as well as the implied warranty under the Japanese Civil Code
(kashi-tampo), is limited to one year from purchase. This warranty does not
cover the cost of installation, removal, or reinstallation, or damage resulting
from misuse, abuse, or improper or incorrect repair, or damages from improper
wiring or installation. This warranty does not cover incidental, consequential,
or any special damages. Lutron Asuka Company’s liability on any claim for
damages arising out of or in connection with the manufacture, sale, installation,
delivery, or use of the unit shall never exceed the purchase price of the unit.
Lutron, Pico, and PowPak are registered trademarks and Radio Powr
Savr is a trademark of Lutron Electronics Co., Inc.
©2013 Lutron Electronics Co., Inc.
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299 U.S.A.
Set a Favorite Light Level
For Pico® Wireless Controls with a Favorite
Button.
A Adjust lights to desired level:
Use Raise button “ ” or Lower button “ ”
on Pico® Wireless Control.
Raise
Lower
B Save favorite level:
Press and hold Favorite button for
6 seconds.
Favorite
Note: In some instances, it may be necessary
to reset the PowPak® Dimming Module and
connected devices back to factory default
settings. Before beginning, make sure that all
devices are connected and powered.
A Triple-tap any button on the PowPak® Dimming
Module and hold until the LED begins to flash
slowly; release button.
B Within 3 seconds of the start of flashing,
triple‑tap the same button again and the LEDs
will flash rapidly indicating that the unit has
been reset to factory defaults.
Note: Any associations or programming
previously set up with the PowPak® will be
erased and will need to be re‑programmed.
Set Minimum Light Level
Set Occupancy Light Levels
Note: Unoccupied light level is always the minimum light
level and cannot be adjusted.
A Set desired occupancy light levels:
Use Raise/Lower buttons “ / ” on the PowPak®
Dimming Module or Raise/Lower buttons “ / ” on all
associated Pico® Wireless Controls.
Note: If certain lights should be
unaffected by occupancy, turn
lights off using PicoR Wireless
Control(s).
B Save occupancy light levels:
Press and hold Test button for
6 seconds on any associated
Radio Powr SavrTM Occupancy
Sensor without a “a” button.
Release when Sensor lens
starts to flash
Or, press and hold “a”
button for 6 seconds on
any associated Radio Powr
SavrTM Occupancy Sensor.
Release when Sensor lens
starts to flash
Press and hold Lower button “ ” for 12 seconds.
Lights will flash high-low-high and LED will begin flashin
Adjust the low-end trim:
Use Raise button “ ” and Lower button
“ ” to adjust and set the lights to the
Notes
desired low-end (1 to 45%).
Depending on the fixtu e
Save the low-end trim:
manufacturer or load, low-end
and high-end trim may need to be
Press and hold Toggle button “ ” for
adjusted.
6 seconds to save setting.
• Trim low-end to ensure a stable
LED will begin flashing and then tu n solid
light level because some loads will
to indicate new level has been saved.
flicker or d op out if trimmed too
High-End Trim
low.
Enter high-end trim adjustment mode:
• Be sure that you can turn on the
lights to the low-end trim level
Press and hold Raise button “ ” for
without any abnormal operation.
12 seconds.
• The factory default high-end trim
Lights will flash high-low-high and LED
will normally be sufficient for mos
will begin flashing
applications. Trim as desired.
Adjust the high-end trim:
Use Raise button “ ” and Lower
button “ ” to adjust and set the lights
to the desired high-end (55 to 100%).
Save the high-end trim:
Ballasts cannot be controlled • Ensure that the breaker(s) to the PowPak® Dimming Module are energized.
• Ensure that the PowPak® Dimming Module switched hot lead is wired to the ballast(s).
locally from PowPak®
Press and hold Toggle button “ ” for
• Ensure that the PowPak® Dimming Module 0 –10 V control lines are wired to the ballast(s).
Dimming Module.
6 seconds to save setting.
•
Reset to factory defaults.
LED will begin flashing and then tu n
solid to indicate new level has been
• Ensure that 0 –10 V control lines are wired properly.
Lights do not dim as
saved.
• Ensure that fixtu e does not require an inverted signal (10 – 0 V control)
expected.
Troubleshooting
Certain applications (e.g., hallways), may
require that the lights never turn off. For
these areas, activate Minimum Light Level
mode.
A Enter minimum light level adjustment
mode:
Press and hold Toggle button “ ” and
Lower button “ ” for 12 seconds. Lights
will flash hig ‑low‑high and LED will begin
flashing
If lights stop flashing and go to high-end,
the minimum light level is set to OFF
(default).
If lights stop flashing and go to low-end,
the minimum light level is ON and set to
low-end.
B Change the minimum light level:
Press Raise button “ ” to set minimum
light level to low-end.
Press Lower button “ ” to set minimum
light level to OFF.
C Save the minimum light level:
Press and hold Toggle button “ ” for
6 seconds. LED will quickly flash to
indicate that new level has been saved.
Low-End Trim
A Enter low-end trim adjustment mode:
Reset Factory Defaults
Set Low-End and High-End Trim
www.lutron.jp
Lights do not respond to
Wireless Transmitter(s).
• Ensure that the breaker(s) to the PowPak® Dimming Module and ballasts are energized.
• Ensure that Wireless Transmitters are associated to the PowPak® Dimming Module.
Wireless Transmitter(s)
cannot be associated to
PowPak® Dimming Module.
• Reset to factory defaults.
• The maximum number of Wireless Transmitters have been associated to the PowPak® Dimming
Module. To remove a previously set up Wireless Transmitter, tap a Wireless Transmitter button
three times; on the third tap hold for three seconds and then tap three more times.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2014:01:22 13:15:52-05:00
Keywords                        : Lutron, PowPak, 0-10, V/PWM, Dimming, Module, Japan, Installation, Sheet, 041434a, 041-434a, RMP-5PWM-DV-B, RMP-5T-DV-B
Modify Date                     : 2014:02:10 13:53:05-05:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2014:02:10 13:53:05-05:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:2d07346f-717f-44c7-88c2-c1791f093669
Original Document ID            : xmp.did:B9A671108F48E211AD8DDE0A1DBE8AD0
Document ID                     : xmp.id:2260512E9183E311B3FFC45CAC6C2496
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:2160512E9183E311B3FFC45CAC6C2496
Derived From Document ID        : xmp.did:2160512E9183E311B3FFC45CAC6C2496
Derived From Original Document ID: xmp.did:B9A671108F48E211AD8DDE0A1DBE8AD0
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2014:01:22 13:15:52-05:00
Format                          : application/pdf
Title                           : PowPak 0-10 V/PWM Dimming Module Japan Installation Sheet Part #041434a
Description                     : PowPak 0-10 V/PWM Dimming Module Japan Installation Sheet..
Creator                         : 
Subject                         : Lutron, PowPak 0-10 V/PWM Dimming Module, Japan, Installation Sheet, 041434a, 041-434a, RMP-5PWM-DV-B, RMP-5T-DV-B
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 1

EXIF Metadata provided by EXIF.tools