Motorola Solutions 89FT7623 Canopy 5400 Fixed Wireless Transceiver User Manual Release10 5FCCdraft2
Motorola Solutions, Inc. Canopy 5400 Fixed Wireless Transceiver Release10 5FCCdraft2
Contents
- 1. Operations guide pt 1
- 2. operations guide pt 2
- 3. Operations guide pt 2a
- 4. Operations guide pt 3a
- 5. Operations guide pt 3b
- 6. Operations guide pt 3c
- 7. Operations guide pt 3d
- 8. Updated Professional install instructions
Updated Professional install instructions
Software Release 10.5 Release Notes and User Guide Supplement PMP 100 and PTP 100 (FSK) PMP 400 and PTP 200 (OFDM) FCC Draft November 2010 FCC Draft Notices See important regulatory and legal notices in Section 10 on Page 31. Trademarks, Product Names, and Service Names MOTOROLA, the stylized M Logo, Canopy, and all other trademarks indicated as such herein are registered trademarks of Motorola, Inc. ® Reg. US Pat & Tm. Office. All other product or service names are the property of their respective owners. © 2010 Motorola, Inc. All rights reserved http://motorola.wirelessbroadbandsupport.com FCC Draft Release 10.5 Release Notes and User Guide Supplement Table of Contents Introduction .......................................................................................................... 5 1.1 Release 10.5 Overview ................................................................................. 5 1.2 Document Change History ............................................................................ 5 1.3 Abbreviations ................................................................................................ 5 1.4 Feedback on Documentation ........................................................................ 6 1.5 Technical Support ......................................................................................... 6 Applicability .......................................................................................................... 8 Upgrading to Release 10.5 ................................................................................... 9 3.1 Obtaining CNUT Upgrade Packages............................................................. 9 3.2 Network Management ................................................................................... 9 3.3 PMP 430 – Options for 5, 10, and 20 MHz Channel Size .............................. 9 Features .............................................................................................................. 11 4.1 US - Operation to avoid Interference with TDWR ........................................ 12 Resolved Issues ................................................................................................. 16 Known Open Issues ........................................................................................... 17 Notes and Reference .......................................................................................... 18 7.1 Notes .......................................................................................................... 18 7.2 US Region Code Operation......................................................................... 21 7.3 PMP 430 Center Channels.......................................................................... 21 7.4 PMP 100 Series DFS Operation Based on Region Code ............................ 23 7.5 PTP 100 Series DFS Operation Based on Region Code ............................. 24 7.6 PMP 400/430 and PTP 200 DFS Operation Based on Region Code........... 25 Canopy MIB......................................................................................................... 26 Performance Benchmarking Process ............................................................... 27 9.1 Definitions ................................................................................................... 27 9.2 System Performance and System Constraints ............................................ 27 9.3 Benchmark Definition .................................................................................. 29 10 Regulatory and Legal Notices........................................................................... 31 10.1 Important Note on Modifications ................................................................. 31 FCC Draft, November 2010 Page 3 Release 10.5 Release Notes and User Guide Supplement 10.2 National and Regional Regulatory Notices.................................................. 31 10.3 RF Exposure Separation Distances ............................................................ 39 10.4 Legal Notices.............................................................................................. 42 10.5 Limit of Liability ........................................................................................... 44 List of Tables Table 1: Release 10.5 Features ..................................................................................11 Table 2: TDWR Location Information ..........................................................................14 Table 3: Issues resolved in Release 10.5 ....................................................................16 Table 4: Release 10.5 known open issues ..................................................................17 Table 5: Notes first discussed with Release 10.3.1......................................................18 Table 6: Notes first discussed with Release 9.5 ..........................................................19 Table 7: PMP 430 center channels by channel bandwidth and region code ................22 Table 8: PMP 100 (FSK) AP/SM DFS operation based on region code.......................23 Table 9: PTP 100 (FSK) BHM/BHS operation based on region code ..........................24 Table 10: PMP 400/430 and PTP 200 (OFDM) DFS operation based on region code.25 Table 11: US FCC IDs and Industry Canada Certification Numbers and covered configurations ..............................................................................................32 Table 12: China disclosure table .................................................................................38 Table 13: Exposure separation distances....................................................................39 Table 14: Calculated exposure distances and power compliance margins ..................40 List of Figures Figure 1: Applicable products ........................................................................................8 Figure 2: PMP AP and PTP BH Region Code Set to United States .............................21 Figure 3: PPS Benchmark Test Setup .........................................................................30 FCC Draft, November 2010 Page 4 Release 10.5 Release Notes and User Guide Supplement 1 Introduction 1.1 RELEASE 10.5 OVERVIEW Release 10.5 is a general release for all Canopy FSK and OFDM radios, including PMP 100, PMP 400/430, PTP 100, and PTP 200 Series modules. This document contains release note information (resolved issues and known open issues) as well as information that supplements the Motorola PMP Solutions Users Guide (descriptions, procedures, and reference information). For the US, Release 10.5 and this document supports avoiding interfering with Terminal Doppler Weather Radar (TDWR) (used near major airports) when using the 5.4-GHz band, especially within 35 km (21.75 mi) of the TDWR certification and shipment of US 5.4-GHz PMP 430 (OFDM) APs and SMs certification and shipment of US Series P11 5.4-GHz PMP 100 (FSK) APs and SMs and PTP 100 (FSK) BHs For details on these and other Release 10.5 features, see section 4 on page 11. For improvements and issues resolved in Release 10.5, see section 5 on page 16. For release open issues, see section 6 on page 17. Modules should be running Release 10.4 before upgrading to Release 10.5. To manage modules running Release 10.5, including managing features new to this release, use either Prizm 3.3 or Wireless Manager 2.2. 1.2 DOCUMENT CHANGE HISTORY FCC Draft 1.3 Draft for FCC approval process ABBREVIATIONS The following abbreviations and acronyms are used in these notes and related documentation: AES AP BAM BH BHM BHS CAP CEPT CIR CMM CNUT CSM DES DFS DHCP DNS Advanced Encryption Standard Access Point Bandwidth and Authentication Manager Backhaul Module Backhaul Module – Master Backhaul Module – Slave Access Point Module Conference of European Post and Telecommunications Committed Information Rate Cluster Management Module Canopy Network Updater Tool Subscriber Module Data Encryption Standard Dynamic Frequency Selection Dynamic Host Configuration Protocol Domain Name System FCC Draft, November 2010 EIRP EFTA ETSI EU FAA FCC FSK FTP FTPS GPS HPAP IC IETF IP ISM LAN Equivalent Isotropically Radiated Power European Free Trade Association European Telecommunications Standards Institute European Union US Federal Aviation Administration US Federal Communications Commission Frequency Shift Keying File Transfer Protocol Secure FTP Global Positioning System High Performance AP (PMP 430 AP) Industry Canada Internet Engineering Task Force Internet Protocol Industrial, Scientific, Medical Local Access Network Page 5 Release 10.5 Release Notes and User Guide Supplement MAC MIB MIR NAT NTIA Media Access Controller Management Information Base Maximum Information Rate Network Address Translation National Telecommunications and Information Administration OFDM Orthogonal Frequency Division Multiplexing OID SNMP Object Identifier P7/P8/P9/P10/P11 Hardware Series PMP Point to Multi-Point PTP Point to Point RADIUS Remote Authentication Dial In User Service 1.4 RF RLAN SM SNMP SNR TCP/IP Radio Frequency Radio Local Area Network Subscriber Module Simple Network Management Protocol Signal to Noise Ratio Transmission Control Protocol/Internet Protocol VDC Volts Direct Current VID VLAN ID VLAN Virtual LAN WAN Wide Area Network WISPA Wireless Internet Service Providers Association WM One Point Wireless Manager FEEDBACK ON DOCUMENTATION Is this document accurate, complete, and clear? How can it be improved? Please send your feedback on Canopy documentation to technical-documentation@canopywireless.com. 1.5 TECHNICAL SUPPORT Tip! Do not clear the Event Log after you encounter issues. It may be useful to Technical Support, if you need to escalate the issue. Here is the escalation path for resolution of a problem: 1. Check documentation: These Release Notes Motorola PMP Solutions Users Guide, available at http://motorola.wirelessbroadbandsupport.com/software. 2. Consider checking the Community Forum and Knowledge Base at http://motorola.wirelessbroadbandsupport.com/support/community. 3. Consider checking the Support Home Page at http://motorola.wirelessbroadbandsupport.com/support/technical.php 4. Escalate the problem to your supplier or reseller. 5. Escalate the problem to Technical Support or other designated Tier 3 technical support: Email: EMS-EICC-RM@motorola.com Phone: U.S. and Canada 1-866-961-9288 Europe, Middle East, and Africa Denmark 043682114 France 0157323434 Germany 06950070204 Italy 0291483230 Lithuania 880 030 828 FCC Draft, November 2010 Netherlands Norway Portugal Spain Russia Saudi Arabia South Africa United Kingdom All other countries 0202061404 24159815 0217616160 0912754787 810 800 228 41044 800 844 5345 0800981900 0203 0277499 +420 533 336 946 Page 6 Release 10.5 Release Notes and User Guide Supplement Latin and Central America Argentina 0800-666-2789 Brazil 0800-891-4360 Columbia 01-800-912-0557 Mexico 001-800-942-7721 Peru 0800-70-086 All other countries +420 533 336 946 Asia and Pacific Australia Northern China Southern China China, local DID Hong Kong India Japan 1 800 457 439 10 800 713 0885 10 800 130 0867 +86 21 6108 6109 30 027 861 000 800 100 3098 221626765 Japan, PSTN South Korea Malaysia New Zealand Philippines Singapore Taiwan Thailand Indonesia All other countries (81) 335 708 643 080 681 0880 1 800 812 384 0 800 448 472 63 29 003 057 64 155 110 00 801 14 8690 001 800 441 0950 001 803 015 20 20530 +420 533 336 946 When you send e-mail or call, please include, as appropriate, software release on each module, IP addresses, MAC addresses, and features enabled, like NAT, VLAN, high priority channel, or CIR. You may be asked to run the Support Tool on CNUT or Prizm to provide a complete network picture. FCC Draft, November 2010 Page 7 Release 10.5 Release Notes and User Guide Supplement 2 Applicability Release 10.5 is a general release recommended for all the products shown in Figure 1. Modulation and Module Type FSK AP/SM/BH PMP Radio Series (Point-to-MultiPoint) PTP Radio Series (Point-To-Point) PMP 100 Series PTP 100 Series Frequencies: 900MHz, 2.4, 5.1, 5.2, 5.4, 5.7, 5.9, 6.050-GHz Frequencies: 2.4, 5.2, 5.4, 5.7-GHz Note: P7 and P8 APs cannot be upgraded Note: AES P7 and P8 SMs cannot be upgraded (All DES SMs can be) Note: P7 and P8 BHs cannot be upgraded PMP 430 Series N/A Frequencies: 5.4-GHz PMP 54430 5.8-GHz PMP 58430 N/A PMP 400 Series PTP 200 Series Frequencies: 4.9-GHz PMP 49400 5.4-GHz PMP 54400 Frequencies: 4.9-GHz PTP 49200 5.4-GHz PTP 54200 OFDM AP/SM OFDM AP/SM/BH Figure 1: Applicable products Not all products are available in all markets. Please check with your local reseller for availability. FCC Draft, November 2010 Page 8 Release 10.5 Release Notes and User Guide Supplement 3 Upgrading to Release 10.5 Use version 3.20.13 of the Network Updater Tool (CNUT) to upgrade to Release 10.5. CNUT and its release notes can be downloaded from the Motorola wireless broadband support web site: http://motorola.wirelessbroadbandsupport.com/software/ Modules in operating sectors should be on Release 10.4 before upgrading to avoid upgrade issues. 3.1 OBTAINING CNUT UPGRADE PACKAGES To download the Canopy software to your computer, perform the following steps: 1. Go to http://motorola.wirelessbroadbandsupport.com/software. 2. Follow the directions on that page to access the software download page. 3. On the software download page, select the appropriate package or packages. Options include [for betas, use packages provided by technical support] CANOPY105BUILDOFFICIAL_DES.pkg3 CANOPY105BUILDOFFICIAL_AES.pkg3 CANOPY105BUILDOFFICIAL_OFDM_DES.pkg3 CANOPY105BUILDOFFICIAL_OFDM_AES.pkg3 4. Click Accept User Agreement and Request Download Links. RESULT: You will receive an email with a link or links to the software. 5. In the email sent to you, click on the desired link or links. RESULT: The appropriate.pkg3 package or packages will download to your computer. For additional information on using CNUT, see the CNUT help file or click on the Help menu in the CNUT application. 3.2 NETWORK MANAGEMENT Either One Point Wireless Manager or Prizm can be used to manage Motorola PMP and PTP networks. For additional information, see 3.3 One Point Wireless Manager: (http://motorola.wirelessbroadbandsupport.com/support/opws/software/ Prizm: http://motorola.wirelessbroadbandsupport.com/software/ PMP 430 – OPTIONS FOR 5, 10, AND 20 MHZ CHANNEL SIZE PMP 430 APs and SMs ship with a 10-MHz channel size. Using CNUT 3.20.13 this can be changed to 20 MHz or 5 MHz. Note for US and Canadian Operators: 5.4-GHz PMP 430 APs and SMs with a US model number (and a locked Region Code of US) or a Region Code of Canada do not support a 5 MHz channel size, consistent with FCC certification and Industry Canada certification. (5.7-GHz PMP 430 APs and SMs do include a 5-MHz channel size, consistent with their certifications.) Changing channel size on an AP requires using CNUT. (CNUT loads the appropriate software components into the AP.) FCC Draft, November 2010 Page 9 Release 10.5 Release Notes and User Guide Supplement Changing channel size on deployed SMs can be done on the SM GUI but is usually better done using CNUT, as CNUT changes all the SMs in a sector at once. Changing channel size on an installing SM should be done on the SM GUI. The AP and the SM must have the same channel size to connect. Important: In an operating sector, use CNUT to change the channel size of the SMs first, then the AP. If you change the AP’s channel size first, SMs won’t register to it since the AP and SMs are operating at different channel sizes. You will have to change the AP back before proceeding. Important for US and Canadian Operators: Don’t change 5.4-GHz APs to 5-MHz channel size. CNUT will change a PMP 430 AP to 5-MHz channel size regardless of the Region Code, but a US or Canada 5.4-GHz PMP 430 AP will boot with transmit disabled, consistent with its certification, and you will have to change the AP back to 10 MHz or 20 MHz channel size using CNUT before proceeding. Don’t set 5.4-GHz SMs to 5-MHz channel size. PMP 430 SMs with a Region Code of US or Canada do not provide the option for a 5-MHz channel. However, if the Region Code isn’t set or is set to another region, you can set the SM to 5-MHz channel size, but it won’t connect to a US or Canada AP, and you will need to change it to the same channel size as the AP to connect. See the CNUT 3.20.13 release notes for specific procedures for setting PMP 430 channel size. FCC Draft, November 2010 Page 10 Release 10.5 Release Notes and User Guide Supplement 4 Features Release 10.5 adds the features listed in Table 1. Table 1: Release 10.5 Features Regions Affected US Products Affected All 5.4-GHz 5.4-GHz PMP 100 (FSK) 5.4-GHz PTP 100 (FSK) Feature Operation to avoid interference with Terminal Doppler Weather Radar (TDWR) Description See for Details To avoid interference with TDWR (47 locations, near major airports), 5.4-GHz US radios must ◦ be professionally installed Section 4.1 ◦ 5.4-GHz PMP 430 (OFDM) 5.4-GHz PMP 400 (OFDM) http://www.spectrumbridge.com/udia/se arch.aspx supports the necessary map analysis and includes a database for registering the location of these radios to expedite interference resolution. 5.4-GHz PTP 200 (OFDM) US US 5.4-GHz PMP 430 (OFDM) have a transmit frequency set on the AP/BHM at least 30 MHz (center-to-center) from any TDWR within 35 km (21.75 mi) of the AP/BHM or any of its SMs/BHS. US FCC Certification of new product US 5.4-GHz PMP 430 APs and SMs are now approved for sale in the US. As certified, the US 5.4-GHz PMP 430 AP is limited to operate at ◦ ◦ no higher than 85% Data Downlink % 10-MHz and 20-MHz channel sizes, but not 5-MHz Section 7.6, Table 10 Section 10.2.1, Table 11 Lens and reflector were not included in the certification. US US P11 Hardware Series 5.4-GHz PMP 100 (FSK) US FCC Certfication of new hardware series US P11 Hardware Series 5.4-GHz PTP 100 (FSK) US P11 5.4-GHz PMP 100 APs and SMs and PTP 100 BHs are now approved for sale in the US. As certified, the US P11 PMP 100 AP and PTP 100 BHM is limited to operate at ◦ Section 7.5, Table 8, Table 9 Section 10.2.1, Table 11 no higher than 75% Data Downlink % (Older hardware series are not limited by Release 10.5.) Canada 5.4-GHz PMP 430 (OFDM) IC Certification of new product 5.4-GHz PMP 430 APs and SMs are now approved for sale in Canada. As certified, the AP is limited to Section 10.2.2 and Table 11 10-MHz and 20-MHz channel sizes, but not 5-MHz For compliant operation, the Region Code must be set to Canada by the professional installer. ◦ FCC Draft, November 2010 Page 11 Release 10.5 Regions Affected Canada Release Notes and User Guide Supplement Products Affected P11 Hardware Series 5.4-GHz PMP 100 (FSK) Feature IC Certfication of new hardware series P11 Hardware Series 5.4-GHz PTP 100 (FSK) 4.1 Description P11 Hardware Series 5.4-GHz PMP 100 APs and SMs and PTP 100 BHs are now approved for sale in Canada. See for Details Section 10.2.2 and Table 11 For compliant operation, the Region Code must be set to Canada by the professional installer. US - OPERATION TO AVOID INTERFERENCE WITH TDWR The US FCC, NTIA, FAA, and industry are working to resolve interference to Terminal Doppler Weather Radar (TDWR) systems used near airports that has occurred from some outdoor wireless systems operating in the 5470 MHz – 5725 MHz band. These wireless devices are subject to Section 15.407. When operating as a master device they are required to implement radar detection and DFS functions and radios must not transmit on channels which overlap the 5600-5650 MHz band used by TDWR. Additional information is available from the FCC’s Knowledge Database (KDB) Publication 443999 “Interim Plans to Approve UNII Devices Operating in the 5470-5725 MHz Band with Radar Detection and DFS Capabilities” available at https://fjallfoss.fcc.gov/kdb/GetAttachment.html?id=33781 the Wireless Internet Service Providers Association (WISPA) in coordination with Spectrum Bridge: http://www.spectrumbridge.com/udia/home.aspx. 5.4-GHz radios must be professionally installed. The professional installer must have the following expertise: Understanding of the configurations outlined in Table 11: US FCC IDs and Industry Canada Certification Numbers and covered configurations, especially those applicable to the 5470-5725 MHz U-NII band. Understanding of the master/slave operation of the AP/BHM and SM/BHS – that the AP or BHM determines the transmission frequency for both master and slave. Understanding of the SM/BHS frequency scan selection settings and how they can be set to prevent scanning and therefore transmission on any specific frequencies. Understanding of the option to set primary and two alternate frequencies on the AP or BHM. Ability to use the GUI to set the primary and alternate transmit frequencies on an AP or BHM, scanned frequencies on an SM or BHS, and Transmit Output Power of a radio. Ability to use the spectrum analyzer feature of the radio to observe the local RF environment. Ability to determine if a radio is within 35 km (21.75 mi) of any Terminal Doppler Weather Radar (TDWR) using the Search function available at http://www.spectrumbridge.com/udia/search.aspx, or using various mapping programs and the data from in Table 2: TDWR Location Information. Ability to set the AP/BHM’s transmit frequency (frequencies, if using alternate frequencies) and SM/BHS’s scanned frequencies at least 30 MHz (center-to-center) from any TDWR operating frequency or frequencies within 35 km of the radio. To gain this expertise the following training is required: FCC Draft, November 2010 Page 12 Release 10.5 Release Notes and User Guide Supplement Study of the documentation Familiarization in a lab or test environment Hands-on training with an experienced installer. Procedure 1 provides the specific instructions to avoid interfering with TDWR when using 5.4GHz APs, SMs, and BHs. Procedure 1: Avoiding interference with Terminal Doppler Weather Radar (TDWR) 1. Use standard installation procedures with the additional steps outlined below. 2. Confirm the AP, SM, or BH has a Region Code of US. If it doesn’t, set the Region Code to US. Note, all radios currently shipping to the US and older radios previously set to the US Region Code and upgraded to a recent release are “hardset” to the US Region Code. 3. For each 5.4-GHz AP, BH, or SM, determine if it is within 35 km (21.75 mi) of any Terminal Doppler Weather Radar (TDWR). This can be done using the map search tool at http://www.spectrumbridge.com/udia/search.aspx, or other mapping tools using the data from Table 2. 4. If an AP or BHM is within 35 km (21.75 mi) of any TDWR, set the primary transmit frequency (and alternate frequencies, if used) to a frequency (or frequencies) at least 30 MHz (center-to-center) from the TDWR operation frequency shown on http://www.spectrumbridge.com/udia/search.aspx or in Table 2. 5. If an SM or BHS is within 35 km (21.75) mi of any TDWR Ensure its AP or BHM is using primary and alternate (if used) transmit frequencies that are at least 30 MHz from the TDWR operation frequency Set the SM’s or BHS’s scanned frequencies to not include frequencies within 30 MHz of the TDWR operation frequency. Note, even if the AP or BHM itself is more than 35 km from the TDWR, if any of its SMs or BHS are within 35 km, it must operate at least 30 MHz from the TDWR operation frequency. Note, in some instances an AP, BH, or SM may be within 35 km of multiple TDWRs. In this case, the AP, BH, or SM must use a frequency at least 30 MHz from all local TDWR operation frequencies. 6. Register each 5.4-GHz AP, SM, or BH operating within 35 km (21.75 mi) of any TDWR in the voluntary WISPA-sponsored database at http://www.spectrumbridge.com/udia/home.aspx. Note, this database may help expedite resolution of any interference to TDWRs. 7. Registration includes, at a minimum, Latitude, Longitude, and External Antenna Model. When registering a device, choose whether to allow General Access or to have the device information viewable only by you and government representatives. =========================== end of procedure =========================== FCC Draft, November 2010 Page 13 Release 10.5 Release Notes and User Guide Supplement Table 2: TDWR Location Information State City Longitude Latitude Frequency AZ CO FL FL FL FL FL GA IL IL IN KS KY KY LA MA MD MD MD MI MN MO MO MS NC NC NJ NJ NV NY OH OH OH OK OK OK OK PA PR TN TX TX TX TX UT VA WI PHOENIX DENVER FT LAUDERDALE MIAMI ORLANDO TAMPA WEST PALM BEACH ATLANTA MCCOOK CRESTWOOD INDIANAPOLIS WICHITA COVINGTON CINCINNATI LOUISVILLE NEW ORLEANS BOSTON BRANDYWINE BENFIELD CLINTON DETROIT MINNEAPOLIS KANSAS CITY SAINT LOUIS DESOTO COUNTY CHARLOTTE RALEIGH DURHAM WOODBRIDGE PENNSAUKEN LAS VEGAS FLOYD BENNETT FIELD DAYTON CLEVELAND COLUMBUS AERO. CTR TDWR #1 AERO. CTR TDWR #2 TULSA OKLAHOMA CITY HANOVER SAN JUAN NASHVILLE HOUSTON INTERCONTL PEARLAND DALLAS LOVE FIELD LEWISVILLE DFW SALT LAKE CITY LEESBURG MILWAUKEE W 112 09 46 W 104 31 35 W 080 20 39 W 080 29 28 W 081 19 33 W 082 31 04 W 080 16 23 W 084 15 44 W 087 51 31 W 087 43 47 W 086 26 08 W 097 26 13 W 084 34 48 W 085 36 38 W 090 24 11 W 070 56 01 W 076 50 42 W 076 37 48 W 076 57 43 W 083 30 54 W 092 55 58 W 094 44 31 W 090 29 21 W 089 59 33 W 080 53 06 W 078 41 50 W 074 16 13 W 075 04 12 W 115 00 26 W 073 52 49 W 084 07 23 W 082 00 28 W 082 42 55 W 097 37 31 W 097 37 43 W 095 49 34 W 097 30 36 W 080 29 10 W 066 10 46 W 086 39 42 W 095 34 01 W 095 14 30 W 096 58 06 W 096 55 05 W 111 55 47 W 077 31 46 W 088 02 47 N 33 25 14 N 39 43 39 N 26 08 36 N 25 45 27 N 28 20 37 N 27 51 35 N 26 41 17 N 33 38 48 N 41 47 50 N 41 39 05 N 39 38 14 N 37 30 26 N 38 53 53 N 38 02 45 N 30 01 18 N 42 09 30 N 38 41 43 N 39 05 23 N 38 45 32 N 42 06 40 N 44 52 17 N 39 29 55 N 38 48 20 N 34 53 45 N 35 20 14 N 36 00 07 N 40 35 37 N 39 56 57 N 36 08 37 N 40 35 20 N 40 01 19 N 41 17 23 N 40 00 20 N 35 24 19 N 35 23 34 N 36 04 14 N 35 16 34 N 40 30 05 N 18 28 26 N 35 58 47 N 30 03 54 N 29 30 59 N 32 55 33 N 33 03 53 N 40 58 02 N 39 05 02 N 42 49 10 5610 MHz 5615 MHz 5645 MHz 5605 MHz 5640 MHz 5620 MHz 5615 MHz 5615 MHz 5615 MHz 5645 MHz 5605 MHz 5603 MHz 5610 MHz 5646 MHz 5645 MHz 5610 MHz 5635 MHz 5645 MHz 5615 MHz 5615 MHz 5610 MHz 5605 MHz 5610 MHz 5610 MHz 5608 MHz 5647 MHz 5620 MHz 5610 MHz 5645 MHz 5647 MHz 5640 MHz 5645 MHz 5605 MHz 5610 MHz 5620 MHz 5605 MHz 5603 MHz 5615 MHz 5610 MHz 5605 MHz 5605 MHz 5645 MHz 5608 MHz 5640 MHz 5610 MHz 5605 MHz 5603 MHz Terrain Elevation (MSL) (ft) 1024 5643 10 72 14 20 962 646 663 751 1270 942 617 151 233 184 249 656 1040 1040 551 371 757 400 19 39 1995 922 817 1037 1285 1293 712 1195 1266 59 722 154 36 541 554 4219 361 820 Antenna Height above Terrain (ft) 64 64 113 113 97 80 113 113 97 113 97 80 97 113 97 113 113 113 97 113 80 64 97 113 113 113 113 113 64 97 97 113 113 80 97 113 64 113 113 97 97 80 80 31 80 113 113 Latitude and Longitude are specified in NAD 83 Last updated July 30, 2010 FCC Draft, November 2010 Page 14 Release 10.5 FCC Draft, November 2010 Release Notes and User Guide Supplement Page 15 Release 10.5 Release Notes and User Guide Supplement 5 Resolved Issues Issues resolved in Release 10.5 are listed in Table 3. Table 3: Issues resolved in Release 10.5 Products Affected Issue Discussion TBD Stuck VC messages TBD TBD Every 8 ping lost TBD TBD Latency issue TBD th FCC Draft, November 2010 Page 16 Release 10.5 Release Notes and User Guide Supplement 6 Known Open Issues Known open issues for Release 10.5 are listed in Table 4. Table 4: Release 10.5 known open issues Products affected Description Discussion and Recommendations TBD TBD Release reported TBD FCC Draft, November 2010 Page 17 Release 10.5 Release Notes and User Guide Supplement 7 Notes and Reference 7.1 NOTES Notes and tips for best operation are listed in Table 5, and Table 6. Table 5: Notes first discussed with Release 10.3.1 Products Affected Description Discussion and Recommendations PMP 430 used with Prizm or BAM PMP 430 SM MIR configured by Prizm to greater than max sustained MIR data rate (12257) If the Configuration Source on a PMP 430 AP’s Configuration > General tab is set to Authentication Server or Authentication Server + SM, SMs will receive their MIR settings from Prizm (or BAM). The resulting SM MIR may be greater than the keyed throughput of the SM. For context, the PMP 430 SM is available keyed to have a maximum throughput of 4, 10, 20 or 40 Mbps. If the SM receives a MIR setting from Prizm that is greater than the keyed bandwidth, the SM will cap the MIR using this formula: (desired uplink MIR * SM aggregate capped rate) / desired aggregate rate (desired downlink MIR * SM aggregate capped rate) / desired aggregate rate Note: Desired aggregate rate is the sum of the desired uplink rate and desired downlink rate For example, if a PMP 430 4 Mbps SM with a max MIR cap of 4000 receives a MIR setting from Prizm that is greater than 4000 kbps, it will cap the downlink MIR and the uplink MIR to equal a max of 4000 kbps. Below is an example with Prizm settings of 10000 kbps uplink MIR and 7000 downlink MIR sent to a 4 Mbps SM that is capped at 4000 kbps max MIR: Uplink calculation: (10000 * 4000) / (7000 + 10000) = 2352 kbps Downlink calculation: (7000 *4000) / (7000 + 10000) = 1648 kbps Thus the Uplink MIR of 2352 + Downlink MIR of 1648 = 4000 kbps In this example, the PMP 430 AP sessions page will display a SM uplink and downlink MIR SMCAP as shown below. For reference, the max SM MIR in kbps for each SM type is: 4 Mbps SM = 4000 10 Mbps SM = 10000 20 Mbps SM = 20000 40 Mbps SM = 65535 (displays Unlimited in the Home > General Status tab) FCC Draft, November 2010 Page 18 Release 10.5 Release Notes and User Guide Supplement Table 6: Notes first discussed with Release 9.5 Products Affected Description Discussion and Recommendations All SM – DNS below a NATed SM when DNS Server Proxy is enabled Microsoft Vista and Windows 7 will not route a 169.254/16 subnet used as the default Canopy subnet since these operating systems use 169.254/16 subnet to talk between local machines. This is not an issue if: the PC is connected directly to the NATed SM. the NAT/routing CPE underneath the NATed SM provides DNS services. However; if a NAT/routing CPE that is not providing DNS services (e.g. some home routers) is placed between the SM and the user’s PC, a Microsoft Vista or Windows 7 machine will not route to the default 169.254/16 SM IP address space to access DNS services. Workaround: Reconfigure the SMs NAT LAN address to a private IP address such as 192.168/16, 172.16/12, or 10/8 or leave DNS Server Proxy disabled. All Updating Community Strings on the Web GUI (11699) To flip-flop the read/write and read-only community string names, it is necessary to change one community string to a temp name first before switching community string names. Remote AP Remote AP Sync Input (7427) Remote AP receives sync from SM by setting SYNC Input to Timing Port. However, if this is incorrectly configured as SYNC input to Power port the Remote AP will still correctly receive SYNC. AP Disable TCP ACK prioritizing in broadcast video applications (10263) When optimizing a system for broadcast video, on the AP’s Configuration => General page configure Prioritized TCP ACK to Disabled. AP or SM Procedures for saving an XML file of a spectrum graph (8484) When the SpectrumAnalysis.xml button is clicked on the SM’s Tools > Spectrum Analyzer tab or the AP’s Tools > Remote Spectrum Analyzer tab, the spectrum graph is redisplayed using XML and XSL if the browser supports XSL. To save the underlying XML file, right click and select “Save Target As” on a Windows PC, or equivalent action for other operating systems. SM SM scan frequencies not “cancelled” by SNMP actions (8172) If you make frequency changes on the SM GUI, and then back them out using SNMP, the Reboot Required message remains on the GUI. Workaround: FCC Draft, November 2010 In a system being used for internet access or similar applications prioritizing TCP ACKs improves downloading of FTP files and other activities making significant use of TCP ACKs under heavy load. However, in a system being used for broadcast video or video surveillance, prioritizing TCP ACKs can cause sporadic choppy video in the uplink. If it says Reboot Required, go ahead and reboot, just to clear the message. Page 19 Release 10.5 Release Notes and User Guide Supplement Products Affected Description Discussion and Recommendations All Managing module accounts and passwords (none) The best security practice is to be aware a factory unit comes with root and admin accounts, to plan your approach to accounts, and set passwords for all accounts. A module that either is fresh from the factory or has been operator-reset to factory defaults has two user accounts: root and admin, both with ADMINISTRATOR level permissions. To secure a module, access the Account => Change Users Password tab and add a password to each of these accounts. Adding a password to only one account still leaves the other open. Furthermore, an account without a password will accept any password potentially giving the impression the unit is protected when it isn’t. Alternatively, an operator’s practices may be to delete the admin account or delete the root account and replace them with their own account(s). By default, Prizm, One Point Wireless Manager and CNUT use the root account to manage the module, so if you delete root accounts on modules you will need to make coordinated changes to Prizm, Wireless Manager, and CNUT to access them with your own accounts. All Use 16 or fewer alphanumeric characters in user account names, passwords, and Community Strings (7808) SNMP doesn’t do data-entry checking, so more than 16 characters may be entered, but only 16 characters will be saved and displayed. AP and SM Timed Spectrum Analyzer settings anomaly (7442) Values of Timed Spectrum Analyzer duration and Spectrum Analysis on Boot get saved by clicking any button on the page, not just when clicking Save Changes or Start Time Spectrum Analysis (which is typical operation for other pages). AP and SM Best Practice is to set SM to same Region Code as AP (none) When an SM registers to an AP, it assumes the Region Code and associated parameters of the AP, disregarding any Region code set in the SM by you. However, the best practice is still for you to set a Region Code in the SM so that displayed options are consistent with the region. All Details on pinging Canopy modules (4831) A ping size larger than 1494 bytes to a radio will time out and fail. However, a ping of greater than 1494 bytes to a system that is behind a radio typically succeeds. To gain an accurate view of latency, ping through the radio to a system beyond. Canopy transports ping traffic with the same priority as all transport traffic, but may handle a direct ping with lower priority when running under load. SM AP may be listed twice in SM’s AP Evaluation tab (5298) To help during aiming, the SM’s Tools > AP Evaluation tab maintains AP entries for 15 minutes. If the frequency of an AP is changed, for 15 minutes the AP is listed twice in the AP Evaluation tab, once with the former frequency, and once with the new one. AP and SM When using Link Test with MIR, need to set both ends (4844, 2756) To see the effects of MIR capping, you can run a link test with MIR enabled. To get meaningful results, set Link Test with MIR to Enabled on the Tools => Link Capacity Test tab in both the SM and the AP. When it is enabled on only one end, results are misleading. After you run perform a link test with MIR capping enabled, consider immediately changing Link Test with MIR to Disabled in both the SM and the AP, to avoid mistakenly capping only one end of the link test. FCC Draft, November 2010 Page 20 Release 10.5 Release Notes and User Guide Supplement Products Affected Description Discussion and Recommendations AP and SM Click Spectrum Analyzer Enable button twice (5284) After you click the Enable button in the Tools => Spectrum Analyzer tab, the resulting display may omit bars for some frequencies, especially in frequency bands that have a large number of center channels, such as the 5.4-GHz band. If you clicking Enable again, the display includes the entire spectrum bar graph. TIP: In the Configuration => General tab, set the Webpage Auto Update parameter to a few seconds, to have the Spectrum Analyzer automatically fully displayed and refreshed. You can later reset the Webpage Auto Update time back to 0, to disable refresh. AP and SM Blank screen after logging in to SM through AP Session Status tab (4706) In some instances, depending on network activity and network design, the interface presents a blank screen to a user who logs in to an SM through the Home => Session Status tab in the AP. If you observe this, refresh your browser window. SM When connecting to a hub, use only half duplex Ethernet settings (7557) Ethernet connections set to 10 Base T Full Duplex or 100 Base T Full Duplex will not connect to an SM through a hub, due to the way a hub works. Use half duplex settings when using a hub. 7.2 US REGION CODE OPERATION A 5-GHz PMP 100/400/430 Series AP or a PTP 100/200 Series BH with a Region Code set to United States is not configurable to another Region Code by installers or end users. This is in response to FCC KDB 594280 and ensures that end users and professional installers do not have access to settings which could allow a radio to be configured to operate in a manner other than that which was specified in the FCC equipment authorization grant. Radios sold in the United States and its territories come with the Region Code on the Configuration > General tab pre-configured to United States and not selectable, as shown in Figure 2. Radios sold in regions outside of the United States and its territories are required to be set by the operator to the Region Code of the region in which they are used. Figure 2: PMP AP and PTP BH Region Code Set to United States 7.3 PMP 430 CENTER CHANNELS When the PMP 430 AP is using 5-MHz channels, the center channels can be configured every 2.5 MHz. When it is using 10- or 20-MHz channels, the center channels can be configured every 5 MHz. Available center channels as a function of channel size and regioin are shown in Table 7. Note: PMP430 5.4-GHz for US does not include a 5-MHz channel size. FCC Draft, November 2010 Page 21 Release 10.5 Release Notes and User Guide Supplement Table 7: PMP 430 center channels by channel bandwidth and region code OFDM Radio Model Channel Size Region Code(s) Range of Center Frequencies Available (MHz) Center Channel Spacing # of Center Channels PMP 430 Series AP, 5.4-GHz 5 MHz Australia 5475 – 5597.5 5652.5 – 5715 2.5 MHz 76 Europe & Spain 5472.5 – 5597.5 5652.5 – 5717.5 2.5 MHz 78 Brazil, India, Russia & Other 5475 –5715 2.5 MHz 97 United States, Canada & Australia 5480 – 5595 5655 – 5710 5 MHz 36 Europe & Spain 5475 – 5595 5655 – 5715 5 MHz 38 Brazil, India, Russia & Other 5480 – 5710 5 MHz 47 United States, Canada & Australia 5480 – 5590 5660 – 5710 5 MHz 34 Europe & Spain 5475 – 5590 5660 – 5715 5 MHz 36 Brazil, India, Russia & Other 5480 – 5710 5 MHz 47 United States, Canada, Australia, Brazil & Russia 5727.5 –5845 2.5 MHz 48 Europe & Other 5727.5 –5872.5 2.5 MHz 59 Spain 5727.5 – 5792.5 5817.5 – 5852.5 2.5 MHz 42 India 5827.5 –5872.5 2.5 MHz 19 United States, Canada, Australia, Brazil & Russia 5730 – 5845 5 MHz 24 Europe & Other 5730 – 5870 5 MHz 29 Spain 5730 – 5790 5820 – 5850 5 MHz 20 India 5830 – 5870 5 MHz United States, Canada, Australia, Brazil & Russia 5735 – 5840 5 MHz 22 Europe & Other 5735 – 5865 5 MHz 27 Spain 5735 – 5785 5825 – 5845 5 MHz 16 India 5835 – 5865 5 MHz 10 MHz 20 MHz PMP 430 Series AP, 5.8-GHz 5 MHz 10 MHz 20 MHz FCC Draft, November 2010 Page 22 Release 10.5 7.4 Release Notes and User Guide Supplement PMP 100 SERIES DFS OPERATION BASED ON REGION CODE For reference, Table 8 shows operating based on Region Code, by frequency band and module type. Note: 900MHz and 2.4-GHz are not shown as DFS operation does not apply to these frequencies. Table 8: PMP 100 (FSK) AP/SM DFS operation based on region code Region Code United States Canada 5.1 GHz AP/ SM NA 5.2 GHz AP ≥P10: FCC/IC DFS ≤ P9: no DFS NA ≥ P10: FCC/IC DFS ≤ P9: no DFS Europe Spain NA NA 5.4 GHz SM No effect No effect NA 5.7 GHz AP SM AP SM No effect No effect No effect FCC/IC DFS No 5590-5660 MHz No effect No effect No effect ETSI EN 301 893 v1.3.1 DFS ETSI EN 301 893 v1.3.1 DFS ETSI EN 302 502 v1.2.1 DFS ETSI EN 302 502 v1.2.1 DFS No effect No effect No effect FCC/IC DFS No 5590-5660 MHz P11: Limited to 75% Downlink Data >July 1, 2008 : No 5590-5660 MHz P11: ETSI v1.4.1 DFS >July 1, 2008 : No 5585-5665 MHz Brazil NA NA NA Australia NA NA NA FCC/IC DFS No 5590-5660 MHz No effect No effect No effect Russia Display Community options No effect No effect NA NA No effect No effect India or Other No effect No effect No effect No effect No effect No effect No effect ≤ P10: ETSI v1.3.1 DFS 1. Product sold in the US is locked to the US Region Code and has “US” in the model number. In other cases, set the Region Code to the region you are in, and the software will determine the correct use of DFS. For countries or regions not listed, use a Region Code that provides DFS functionality and channels consistent with your country’s regulatory requirements. 2. Terminal Doppler Weather Radar (TDWR) operates on frequencies 5600 through 5650 MHz. In some countries a “weather notch” is required to avoid impinging on these frequencies. 3. Radios placed on market in Europe after July 1, 2008, can’t impinge on weather radar frequencies. To meet this requirement, the software checks the date code of the module and implements the weather notch accordingly. You can tell if a 5.4-GHz module is “newer” or “older” by setting the Region Code to Europe – if the notch frequencies are not shown on the Configuration => Radio page, then the module is “newer”, if the notch frequencies are shown, the module is “older”. FCC Draft, November 2010 Page 23 Release 10.5 7.5 Release Notes and User Guide Supplement PTP 100 SERIES DFS OPERATION BASED ON REGION CODE For reference, Table 9 shows operating based on Region Code, by frequency band and module type. Table 9: PTP 100 (FSK) BHM/BHS operation based on region code Region Code United States Canada Europe 2.4 GHz 5.1 GHz BH BH No effect No effect No effect NA 5.2 GHz BHM ≥P10: FCC/IC DFS ≤ P9: no DFS NA ≥ P10: FCC/IC DFS ≤ P9: no DFS 5.4 GHz BHS BHM BHS NA BHM BHS FCC/IC DFS No effect No effect No 5590-5660 MHz P11: Limited to 75% Downlink Data FCC/IC DFS No 5590-5660 MHz in FSK ETSI EN 301 893 v1.3.1 DFS NA 5.7 GHz NA >July 1, 08 : No 55905660 MHz in FSK P11: ETSI v1.4.1 DFS No effect No effect No effect No effect No effect No effect ETSI EN 302 502 v1.2.1 DFS ETSI EN 302 502 v1.2.1 DFS No effect No effect No effect No effect No effect No effect ETSI EN 301 893 v1.3.1 DFS >July 1, 08 : No 55855665 MHz in FSK Brazil NA NA NA NA Australia No effect NA NA NA Russia NA Display Community options No effect No effect NA NA No effect No effect India or Other No effect No effect No effect No effect No effect No effect No effect No effect ≤ P10: ETSI v1.3.1 DFS FCC/IC DFS No 5590-5660 MHz in FSK 1. Product sold in the US is locked to the US Region Code and has “US” in the model number. In other cases, set the Region Code to the region you are in, and the software will determine the correct use of DFS. For countries or regions not listed, use a Region Code that provides DFS functionality and channels consistent with your country’s regulatory requirements. 2. Terminal Doppler Weather Radar (TDWR) operates on frequencies 5600 through 5650 MHz. In some countries a “weather notch” is required to avoid impinging on these frequencies. 3. Radios placed on market in Europe after July 1, 2008, can’t impinge on weather radar frequencies. To meet this requirement, the software checks the date code of the module and implements the weather notch accordingly. You can tell if a 5.4-GHz module is “newer” or “older” by setting the Region Code to Europe – if the notch frequencies are not shown on the Configuration => Radio page, then the module is “newer”, if the notch frequencies are shown, the module is “older”. FCC Draft, November 2010 Page 24 Release 10.5 Release Notes and User Guide Supplement 7.6 PMP 400/430 AND PTP 200 DFS OPERATION BASED ON REGION CODE For reference, Table 10 shows operation based on Region Code, by frequency band and radio platform. PMP 400 and PTP 200 are available in the 5.4-GHz frequency band. PMP 430 is available in both the 5.4 and 5.8-GHz frequency bands. Note: The 4.9-GHz PMP 400 and PTP 200 are not shown as DFS operation does not apply to these frequencies. Table 10: PMP 400/430 and PTP 200 (OFDM) DFS operation based on region code Region Code Frequency Radio Platform PMP 400/430 & PTP 200 United States PMP 430 PMP 400/430 & PTP 200 Canada Europe & Spain Brazil Australia Russia India Other SM FCC/IC DFS PMP 430 limited to 85% Downlink Data, no 5-MHz channel size 5.4-GHz 5.8-GHz AP 5.4-GHz No effect No effect No effect FCC/IC DFS PMP 430 - no 5-MHz channel size No effect No effect 5.8-GHz PMP 430 No effect 5.4-GHz PMP 400/430 & PTP 200 ETSI DFS ETSI DFS 5.8-GHz PMP 430 ETSI DFS ETSI DFS 5.4-GHz PMP 400/430 & PTP 200 ETSI DFS No effect 5.8-GHz PMP 430 No effect 5.4-GHz PMP 400/430 & PTP 200 FCC/IC DFS 5.8-GHz PMP 430 No effect No effect 5.4-GHz PMP 400/430 & PTP 200 No effect No effect 5.8-GHz PMP 430 No effect No effect 5.4-GHz PMP 400/430 & PTP 200 No effect No effect 5.8-GHz PMP 430 No effect No effect 5.4-GHz PMP 400/430 & PTP 200 No effect No effect 5.8-GHz PMP 430 No effect No effect No effect No effect 1. Product sold in the US is locked to the US Region Code and has “US” in the model number. In other cases, set the Region Code to the region you are in, and the software will determine the correct use of DFS. For countries or regions not listed, use a Region Code that provides DFS functionality and channels consistent with your country’s regulatory requirements. 2. 3. In some countries and regions, 5600 MHz to 5650 MHz is “notched” out to meet requirements to not transmit in weather radar frequencies. Complies with FCC Report and Order 03-287 and Industry Canada requirements. 4. 5. Complies with ETSI EN 301 893 v1.3.1. Complies with ETSI EN 302 502 v1.2.1. FCC Draft, November 2010 Page 25 Release 10.5 Release Notes and User Guide Supplement 8 Canopy MIB The Canopy Enterprise MIB (Management Information Base) consists of 5 MIB definition files and supports SNMP access to Canopy modules. The MIB files are available for download from the Canopy tab of http://motorola.wirelessbroadbandsupport.com/software. Detailed information on the Canopy MIBs is available at http://motorola.wirelessbroadbandsupport.com/support/online_tools. MIB files are used by Network Management Systems and Element Management Systems, such as the Motorola Prizm and One Point Wireless Manager systems, to support a host of surveillance, monitoring, control, and operational tasks. Information on the Motorola Prizm element management system is available at http://www.motorola.com/Business/USEN/Business+Product+and+Services/Wireless+Broadband+Networks/Point-toMultipoint+Networks/Unlicensed+Point-toMultipoint+Solutions/Element_Management_PTMP_US-EN Information on the Motorola One Point Wireless Manager management system is available at http://www.onepointwireless.com/wirelessmanager/ Prizm and One Point Wireless Manager documentation and installers are available for download from the Canopy tab of http://motorola.wirelessbroadbandsupport.com/software. If you are using Prizm: Prizm 3.3.10 includes the MIB information. You do not need to load MIB files. If you are using One Point Wireless Manager 2.2 or an SNMP network management system (NMS) or element management system (EMS) other than Prizm: Load the MIBs per the instructions for One Point Wireless Manager 2.2 or your NMS or EMS. Important! When loading the Canopy MIB files 1. First load the standard MIB files. 2. Then load the Canopy MIB files. Some NMSs are not sensitive to order, but some require a specific loading order to build a MIB tree. Loading in the recommended order avoids any problems arising from loading sequence. FCC Draft, November 2010 Page 26 Release 10.5 Release Notes and User Guide Supplement 9 Performance Benchmarking Process This section describes the performance benchmarking process. 9.1 DEFINITIONS The following terms are used where these release notes discuss packet processing: Aggregate Throughput Sum of uplink plus downlink traffic. Offered Load Test equipment generates a specified load to the Ethernet interface of a module (SM or the AP). The specifications of the load include both packet size and packet rate. Carried Load Test equipment measures the load delivered at the Ethernet interface of a module. The load is calculated from packet size and number of packets. As resources are exhausted at any point in the system, packets may be dropped. The Carried Load equals the Offered Load minus Dropped Packets. Downlink/Uplink Load Ratio The ratio of downlink Carried Load to uplink Carried Load. NOTE: Do not confuse the Downlink/Uplink Load Ratio with the Downlink Data configuration parameter. The Downlink/Uplink Load Ratio is determined from the Carried Loads. The Downlink Data is set by the operator and determines the split of downlink and uplink slots in the air frame. 9.2 SYSTEM PERFORMANCE AND SYSTEM CONSTRAINTS Different combinations of system inputs will result in different constraints limiting system performance. Larger Packets With larger packets (the system handles packets up to 1522 Bytes), the system constraint is airtime, which can also be stated as slots, or maximum bits per second. This can be calculated as follows: PMP 100 and PTP 100 Backhauls with 20MHz Channels: 64 Bytes/fragment x 2 fragments/slot x 34 slots/frame x 400 frames/sec x 8 bits/byte = 14 Mbps This is an aggregate (uplink plus downlink) limit, as the Canopy system is a Time Division Duplex (TDD) system. 14 Mbps is a typical maximum aggregate throughput for larger packet sizes for an FSK system. Longer range settings can reduce the number of slots in a frame and packet size (breakage on 64-byte boundaries) can affect packing efficiency (the percentage of fragments fully packed with 64 bytes). PMP 430 (5.4 and 5.8-GHz OFDM) with 5MHz Channels: For 1/4 Cyclic Prefix the calculation is 64 Bytes/fragment x 3 fragments/slot x 15 slots/frame x 400 frames/sec x 8 bits/byte = 9.2 Mbps FCC Draft, November 2010 Page 27 Release 10.5 Release Notes and User Guide Supplement For 1/8 Cyclic Prefix the calculation is 64 Bytes/fragment x 3 fragments/slot x 17 slots/frame x 400 frames/sec x 8 bits/byte = 10.4 Mbps For 1/16 Cyclic Prefix the calculation is 64 Bytes/fragment x 3 fragments/slot x 18 slots/frame x 400 frames/sec x 8 bits/byte = 11.0 Mbps With 5MHz channels, 9.2 Mbps is a typical maximum aggregate (uplink plus downlink) throughput for larger packet sizes in a system configured with 1/4 cyclic prefix. For 1/8 cyclic prefix systems 10.4 Mbps is a typical maximum aggregate throughput and for 1/16 cyclic prefix 11.0 Mbps is a typical maximum aggregate throughput. Longer range settings can reduce the number of slots in a frame and packet size (breakage on 64-byte boundaries) can affect packing efficiency (the percentage of fragments fully packed with 64 bytes). PMP 430 (5.4 and 5.8-GHz OFDM) with 10MHz Channels: For 1/4 Cyclic Prefix the calculation is 64 Bytes/fragment x 3 fragments/slot x 33 slots/frame x 400 frames/sec x 8 bits/byte = 20.2 Mbps For 1/8 Cyclic Prefix the calculation is 64 Bytes/fragment x 3 fragments/slot x 37 slots/frame x 400 frames/sec x 8 bits/byte = 22.7 Mbps For 1/16 Cyclic Prefix the calculation is 64 Bytes/fragment x 3 fragments/slot x 42 slots/frame x 400 frames/sec x 8 bits/byte = 25.8 Mbps With 10MHz channels, 20.2 Mbps is a typical maximum aggregate (uplink plus downlink) throughput for larger packet sizes in a system configured with 1/4 cyclic prefix. For 1/8 cyclic prefix systems 22.7 Mbps is a typical maximum aggregate throughput and for 1/16 cyclic prefix 25.8 Mbps is a typical maximum aggregate throughput. Longer range settings can reduce the number of slots in a frame and packet size (breakage on 64-byte boundaries) can affect packing efficiency (the percentage of fragments fully packed with 64 bytes). PMP 430 (5.4 and 5.8-GHz OFDM) with 20MHz Channels: For 1/4 Cyclic Prefix the calculation is 64 Bytes/fragment x 3 fragments/slot x 73 slots/frame x 400 frames/sec x 8 bits/byte = 44.8 Mbps For 1/8 Cyclic Prefix the calculation is 64 Bytes/fragment x 3 fragments/slot x 81 slots/frame x 400 frames/sec x 8 bits/byte = 49.7 Mbps For 1/16 Cyclic Prefix the calculation is 64 Bytes/fragment x 3 fragments/slot x 86 slots/frame x 400 frames/sec x 8 bits/byte = 52.8 Mbps With 20MHz channels, 44.8 Mbps is a typical maximum aggregate (uplink plus downlink) throughput for larger packet sizes in a system configured with 1/4 cyclic prefix. For 1/8 cyclic prefix systems 49.7 Mbps is a typical maximum aggregate throughput and for 1/16 cyclic prefix 52.8 Mbps is a typical maximum aggregate throughput. Longer range settings can reduce the number of slots in a frame and packet size (breakage on 64-byte boundaries) can affect packing efficiency (the percentage of fragments fully packed with 64 bytes). Smaller Packets With smaller packets, the system constraint is processing power in any module handling the traffic stream. Even though there may be airtime or slots available, the overall throughput is limited by packet handling ability. FCC Draft, November 2010 Page 28 Release 10.5 9.3 Release Notes and User Guide Supplement BENCHMARK DEFINITION In a complex system, any measurement depends on system configuration, traffic mix, various settings, and measurement techniques, and so to have reproducible results a “benchmark” is defined. System configuration The PMP benchmark system consists of 3 SMs and 1 Advantage AP, as shown in Figure 3 on page 30. Traffic generation and measurement equipment is connected to both SMs and the AP. Traffic is generated such that any one packet attempts to traverse an SM and then the AP, or the AP and then an SM. No SM-to-SM traffic is included in the benchmark. RF conditions are maintained such that all links run at max rate (2X or 3X). Traffic mix/Packet size All generated packets have a size of 64 Bytes. The packet format used is a valid Ethernet/IP packet. The performance of interest is performance near a 50% Downlink/Uplink Load Ratio. PMP Settings Downlink Data: 50% Control Slots: 2 Range: 2 miles Max rate (2X or 3X) Enabled Encryption: Enabled (DES modules) MIR: 20,000 kbits/sec sustained rate and 500,000 kbits burst allocation (defaults) CIR: 0 (default) NAT: Disabled (default) VLAN: Disabled (default) High Priority: Disabled (default) Downlink Data: 50% Max rate (2X or 3X) Enabled Encryption: Enabled (DES modules) PTP Settings Measurement technique 1. Send a specific number of frames at a specific rate through SMs and AP (uplinks) and AP and SM (downlink) simultaneously. This is the Offered Load. Count the frames that are received correctly at both sides. This is the Carried Load. Repeat this through the load rates of interest. Review the results, noting where the packet loss (the difference between the Offered Load and Carried Load) is essentially zero (<0.001%). 2. Confirm results by running longer tests at selected load rates. 3. Confirm results by varying Downlink/Uplink Load Ratios to ensure no significant changes around the 50% benchmark. FCC Draft, November 2010 Page 29 Release 10.5 Release Notes and User Guide Supplement x/6 pps SM1 pps x/6 pps x/6 pps SM2 AP x/6 pps x/2 pps x/2 pps SM3 x/6 pps x/6 pps Ixia Test Controller and Load Modules All packets 64 Bytes Figure 3: PPS Benchmark Test Setup FCC Draft, November 2010 Page 30 Release 10.5 Release Notes and User Guide Supplement 10 Regulatory and Legal Notices 10.1 IMPORTANT NOTE ON MODIFICATIONS Intentional or unintentional changes or modifications to the equipment must not be made unless under the express consent of the party responsible for compliance. Any such modifications could void the user’s authority to operate the equipment and will void the manufacturer’s warranty. 10.2 10.2.1 NATIONAL AND REGIONAL REGULATORY NOTICES U.S. Federal Communication Commission (FCC) Notification For 900MHz, 2.4, 5.2, 5.4, 5.7 and 5.8-GHz devices: This device complies with Part 15 of the US FCC Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the US FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to correct the interference by one or more of the following measures: Increase the separation between the affected equipment and the unit; Connect the affected equipment to a power outlet on a different circuit from that which the receiver is connected to; Consult the dealer and/or experienced radio/TV technician for help. FCC IDs and the specific configurations covered are listed in Table 11. Specific instructions to avoid interfering with Terminal Doppler Weather Radar (TDWR) are included below Table 11. For 4.9-GHz devices: The 4.9-GHz band is a licensed band allocated to public safety services. State and local government entities that provide public safety services are eligible to apply for 4.9 GHz licenses. For additional information, refer to FCC regulations. FCC Draft, November 2010 Page 31 Release 10.5 Release Notes and User Guide Supplement Table 11: US FCC IDs and Industry Canada Certification Numbers and covered configurations FCC ID Industry Canada Cert Number Frequencies and Channels ABZ89FC5809 109W-9000 8 MHz channels, centered on 906-924 MHz in 1 MHz increments (within the 902928 MHz ISM band) Module Families 9000 SM, AP (PMP 100) Antenna Maximum Tx Output Power 12 dBi integrated antenna 24 dBm (250 mW) 17 dBi Last Mile Gear Cyclone 900-17H Yagi 18 dBm (63 mW) 10 dBi Maxrad Model # Z1681 (MP9027XFPT or Motorola AN900A) flat panel 26 dBm (390 mW) 10 dBi Mars Model # MA-IS91-T2, flat panel 26 dBm (390 mW) 10 dBi MTI Model # MT-2630003/N (MT263003/N) flat panel 26 dBm (390 mW) ABZ89FC5808 109W-2400 20 MHz channels, centered on 2400 BH, SM, 8 dBi internal 2415-2457.5 MHz in 2.5 MHz AP increments (within the 24002400 BH, SM 8 dBi internal + 2483.5 MHz ISM band) 11 dB reflector 25 dBm (340 mW) ABZ89FC3789 109W-5200 20 MHz channels, centered on 5275-5325 MHz in 5 MHz increments (within the 52505350 MHz U-NII band) 5200 BH, SM, 7 dBi internal AP 23 dBm (200 mW) (PMP 100, PTP 100) 7 dBi internal + 18 dB reflector 5 dBm (3.2 mW) 7 dBi internal + 9 dB lens 14 dBm (25 mW) ABZ89FT7623 109W-5400 20 MHz channels, centered on 5495-5585 and 5665-5705 MHz in 5 MHz increments (within the 5470-5725 MHz UNII band with 5600-5650 MHz excluded) 25 dBm (340 mW) 5400 BH, SM, 7 dBi internal AP 23 dBm (200 mW) (PMP 100, PTP 100) 7 dBi internal + 18 dB reflector 5 dBm (3.2 mW) 7 dBi internal + 9 dB lens 14 dBm (25 mW) ABZ89FC5804 109W-5700 20 MHz channels, centered on 5700 BH, SM, 7 dBi internal AP 5735-5840 MHz in 5 MHz increments (within the 57255700 BH, SM 7 dBi internal + 5850 MHz ISM band) 18 dB reflector (PMP 100, PTP 100) 7 dBi internal + 10 dB lens 23 dBm (200 mW) 5700 AP (PMP 100) FCC Draft, November 2010 7 dBi internal + 10 dB lens 23 dBm (200 mW) 23 dBm (200 mW) 19 dBm (80 mW) Page 32 Release 10.5 FCC ID Release Notes and User Guide Supplement Industry Canada Cert Number Frequencies and Channels ABZ89FT7634 109W-5780 5 MHz channels, centered on 5727.5-5845 in 5 MHz increments (within the 57255850 MHz ISM band) Module Families 5780 APC (PMP 430) 10 MHz channels, centered on 5730-5845 in 5 MHz increments (within the 57255850 MHz ISM band) Antenna 17 dBi connectorized PCTEL Model 8514724E01 antenna (60° x 5° -3 dB beam width) with 1 dB connector cable loss 19 dBm 19 dBm 20 MHz channels, centered on 5735-5840 in 5 MHz increments (within the 57255850 MHz ISM band) ABZ89FT7635 109W-5790 5 MHz channels, centered on 5727.5-5845 in 5 MHz increments (within the 57255850 MHz ISM band) Maximum Tx Output Power 19 dBm 5790 SM (PMP 430) 10 dBi (55° x 55° -3 dB beam width) 19 dBm 10 MHz channels, centered on 5730-5845 in 5 MHz increments (within the 57255850 MHz ISM band) 19 dBm 20 MHz channels, centered on 5735-5840 in 5 MHz increments (within the 57255850 MHz ISM band) 19 dBm ABZ89FT7637 109W-5480 10 MHz channels, centered on 5480 APC 5480-5595 and 5655-5710 (PMP 430) MHz in 5 MHz increments (within the 5470-5725 MHz UNII band with 5600-5650 MHz excluded) 18 dBi connectorized PCTEL Model 8514724E01 antenna (60° x 5° -3 dB beam width) with 1 dB connector cable loss 20 MHz channels, centered on 5485-5590 and 5660-5705 MHz in 5 MHz increments (within the 5470-5725 MHz UNII band with 5600-5650 MHz excluded) ABZ89FT7638 109W-5490 10 MHz channels, centered on 5490 SM 5480-5595 and 5655-5710 (PMP 430) MHz in 5 MHz increments (within the 5470-5725 MHz UNII band with 5600-5650 MHz excluded) 20 MHz channels, centered on 5485-5590 and 5660-5705 MHz in 5 MHz increments (within the 5470-5725 MHz UNII band with 5600-5650 MHz excluded) FCC Draft, November 2010 10 dBm 13 dBm 10 dBi (55° x 55° -3 dB beam width) 17 dBm 19 dBm Page 33 Release 10.5 FCC ID Release Notes and User Guide Supplement Industry Canada Cert Number Frequencies and Channels Module Families Antenna ABZ89FT7629 109W-5440 10 MHz channels, centered on 5440 AP 5480-5595 and 5655-5710 (PMP 400) MHz in 5 MHz increments (within the 5470-5725 MHz UNII band with 5600-5650 MHz excluded) 18 dBi connectorized PCTEL Model 8514724E01 antenna (60° x 5° -3 dB beam width) with 1 dB connector cable loss 5440 SM (PMP 400) 17 dBi integrated antenna (15° x 15° -3 dB beam width) 5440 BH (PTP 200) Maximum Tx Output Power 10 dBm 10 dBm ABZ89FT7631 109W-4940 10 MHz channels, centered on 4940 AP 4945-4985 in 5 MHz (PMP 400) increments (within the 49404990 MHz public safety licensed band) 18 dBi connectorized PCTEL Model AP 85010066001 antenna (60° x 5° -3 dB beam width) with 1 dB cable loss 18 dBm 4940 SM (PMP 400) 17 dBi integrated antenna (15.5° x 17.5° (el x az) -3 dB beam width) 18 dBm 4940 BH (PTP 200) To ensure regulatory compliance, including DFS compliance, the professional installer is responsible for: ◦ ◦ ◦ setting the Transmitter Output Power on the Confiiguration => Radio page no higher than listed for a given configuration setting the External Gain on the Configuration => Radio page, if displayed, to the gain of any external device (such as a reflector or lens) following instructions to avoid interfering with Terminal Doppler Weather Radar (TDWR) in the 5470-5725 MHz U-NII band. 10.2.2 Industry Canada (IC) Notification For 900MHz, 2.4-GHz, 5.2-GHz. 5.4-GHz, 5.7-GHz and 5.8-GHz devices: This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Users should be cautioned to take note that in Canada high power radars are allocated as primary users (meaning they have priority) of 5250 – 5350 MHz and 5650 – 5850 MHz and these radars could cause interference and/or damage to license-exempt local area networks (LELAN). This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to RSS-210 of Industry Canada. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to correct the interference by one or more of the following measures: Increase the separation between the affected equipment and the unit; FCC Draft, November 2010 Page 34 Release 10.5 Release Notes and User Guide Supplement Connect the affected equipment to a power outlet on a different circuit from that which the receiver is connected to; Consult the dealer and/or experienced radio/TV technician for help. To reduce potential radio interference to other users, the antenna type and its gain should be chosen so its Equivalent Isotropic Radiated Power (EIRP) is not more than that permitted for successful communication. Industry Canada Certification Numbers and the specific configurations covered are listed in Table 11. This device has been designed to operate with the antennas listed in Table 11 and having a maximum gain as shown in Table 11. Antennas not included or having a gain greater than as shown in Table 11 are strictly prohibited from use with this device. Required antenna impedance is 50 ohms. For 4.9-GHz devices: The 4.9-GHz band is a licensed band allocated to public safety services. Government entities that provide public safety services are eligible to apply for 4.9 GHz licenses. For additional information, refer to Industry Canada regulations. 10.2.3 Regulatory Requirement for CEPT Member States (www.cept.org) When operated in accordance with the instructions for use, Motorola Canopy Wireless equipment operating in the 2.4 and 5.4 GHz bands is compliant with CEPT Recommendation 70-03 Annex 3 for Wideband Data Transmission and HIPERLANs. For compliant operation in the 2.4 GHz band, the transmit power (EIRP) from the built-in patch antenna and any associated reflector dish shall be no more than 100mW (20dBm). For compliant operation in the 5.4 GHz band, the transmit power (EIRP) from the built-in patch antenna and any associated reflector dish shall be no more than 1 W (30 dBm). The following countries have completely implemented CEPT Recommendation 70-03 Annex 3A (2.4 GHz band): EU & EFTA countries: Austria, Belgium, Denmark, Spain, Finland, Germany, Greece, Iceland, Italy, Ireland, Liechtenstein, Luxembourg, Netherlands, Norway, Portugal, Switzerland, Sweden, UK New EU member states: Bulgaria, Czech Republic, Cyprus, Estonia, Hungary, Lithuania, Latvia, Malta, Poland, Slovenia, Slovakia Other non-EU & EFTA countries: Bosnia and Herzegovina, Turkey The following countries have a limited implementation of CEPT Recommendation 70-03 Annex 3A: France – Outdoor operation at 100mW is only permitted in the frequency band 2400 to 2454 MHz; − Any outdoor operation in the band 2454 to 2483.5MHz shall not exceed 10mW (10dBm); − Indoor operation at 100mW (20dBm) is permitted across the band 2400 to 2483.5 MHz French Overseas Territories: − Guadeloupe, Martinique, St Pierre et Miquelon, Mayotte – 100mW indoor & outdoor is allowed − Réunion and Guyana – 100mW indoor, no operation outdoor in the band 2400 to 2420MHz Italy – If used outside own premises, general authorization required Luxembourg - General authorization required for public service Romania – Individual license required. T/R 22-06 not implemented Motorola Canopy Radios operating in the 2400 to 2483.5MHz band are categorized as “Class 2” devices within the EU and are marked with the class identifier symbol , denoting that national restrictions apply (for example, France). The French restriction in the 2.4 GHz band will be removed in 2011. This 2.4 GHz equipment is “CE” marked to show compliance with the European Radio & Telecommunications Terminal Equipment (R&TTE) directive 1999/5/EC. The relevant Declaration of Conformity can be found at http://motorola.wirelessbroadbandsupport.com/doc.php. FCC Draft, November 2010 Page 35 Release 10.5 Release Notes and User Guide Supplement Where necessary, the end user is responsible for obtaining any National licenses required to operate this product and these must be obtained before using the product in any particular country. However, for CEPT member states, 2.4 GHz Wideband Data Transmission equipment has been designated exempt from individual licensing under decision ERC/DEC(01)07. For EU member states, RLAN equipment in both the 2.4 & 5.4GHz bands is exempt from individual licensing under Commission Recommendation 2003/203/EC. Contact the appropriate national administrations for details on the conditions of use for the bands in question and any exceptions that might apply. Also see www.ero.dk for further information. Motorola Canopy Radio equipment operating in the 5470 to 5725 MHz band are categorized as “Class 1” devices within the EU in accordance with ECC DEC(04)08 and are “CE” marked to show compliance with the European Radio & Telecommunications Terminal Equipment (R&TTE) directive 1999/5/EC. The relevant Declaration of Conformity can be found at http://motorola.wirelessbroadbandsupport.com/doc.php. A European Commission decision, implemented by Member States on 31 October 2005, makes the frequency band 5470-5725 MHz available in all EU Member States for wireless access systems. Under this decision, the designation of Canopy 5.4GHz products become “Class 1 devices” and these do not require notification under article 6, section 4 of the R&TTE Directive. Consequently, these 5.4GHz products are only marked with the symbol and may be used in any member state. For further details, see http://europa.eu.int/information_society/policy/radio_spectrum/ref_documents/index_en.htm 10.2.4 European Union Notification for 5.7 and 5.8 GHz Product The 5.7 and 5.8 GHz connectorized product is a two-way radio transceiver suitable for use in Broadband Wireless Access System (WAS), Radio Local Area Network (RLAN), or Fixed Wireless Access (FWA) systems. It is a Class 2 device and uses operating frequencies that are not harmonized throughout the EU member states. The operator is responsible for obtaining any national licenses required to operate this product and these must be obtained before using the product in any particular country. This equipment is marked to show compliance with the European R&TTE directive 1999/5/EC. The relevant Declaration of Conformity can be found at http://motorola.wirelessbroadbandsupport.com/doc.php. 10.2.5 Equipment Disposal Waste (Disposal) of Electronic and Electric Equipment Please do not dispose of Electronic and Electric Equipment or Electronic and Electric Accessories with your household waste. In some countries or regions, collection systems have been set up to handle waste of electrical and electronic equipment. In European Union countries, please contact your local equipment supplier representative or service center for information about the waste collection system in your country. 10.2.6 EU Declaration of Conformity for RoHS Compliance Motorola hereby, declares that these Motorola products are in compliance with the essential requirements and other relevant provisions of Directive 2002/95/EC, Restriction of the use of certain Hazardous Substances (RoHS) in electrical and electronic equipment. The relevant Declaration of Conformity can be found at http://motorola.wirelessbroadbandsupport.com/doc.php. 10.2.7 UK Notification The 5.7 and 5.8 GHz connectorized product has been notified for operation in the UK, and when operated in accordance with instructions for use it is compliant with UK Interface Requirement IR2007. For UK use, installations must conform to the requirements of IR2007 in terms of EIRP spectral density against elevation FCC Draft, November 2010 Page 36 Release 10.5 Release Notes and User Guide Supplement profile above the local horizon in order to protect Fixed Satellite Services. The frequency range 5795-5815 MHz is assigned to Road Transport & Traffic Telematics (RTTT) in the U.K. and shall not be used by FWA systems in order to protect RTTT devices. UK licensing specifies that radiolocation services shall be protected by a Dynamic Frequency Selection (DFS) mechanism to prevent co-channel operation in the presence of radar signals. 10.2.8 Belgium Notification Belgium national restrictions in the 2.4 GHz band include EIRP must be lower then 100 mW For crossing the public domain over a distance >300m the user must have the authorization of the BIPT. No duplex working 10.2.9 Luxembourg Notification For the 2.4 GHz band, point-to-point or point-to-multipoint operation is only allowed on campus areas. 5.4GHz products can only be used for mobile services. 10.2.10Czech Republic Notification 2.4 GHz products can be operated in accordance with the Czech General License No. GL-12/R/2000. 5.4 GHz products can be operated in accordance with the Czech General License No. GL-30/R/2000. 10.2.11Norway Notification Use of the frequency bands 5725-5795 / 5815-5850 MHz are authorized with maximum radiated power of 4 W EIRP and maximum spectral power density of 200 mW/MHz. The radio equipment shall implement Dynamic Frequency Selection (DFS) as defined in Annex 1 of ITU-R Recommendation M.1652 / EN 301 893. Directional antennae with a gain up to 23 dBi may be used for fixed point-to-point links. The power flux density at the border between Norway and neighboring states shall not exceed – 122.5 dBW/m measured with a reference bandwidth of 1 MHz. Canopy 5.7 and 5.8 GHz connectorized products have been notified for use in Norway and are compliant when configured to meet the above National requirements. Users shall ensure that DFS functionality is enabled, maximum EIRP respected for a 20 MHz channel, and that channel spacings comply with the allocated frequency band to protect Road Transport and Traffic Telematics services (for example, 5735, 5755, 5775 or 5835 MHz are suitable carrier frequencies). Note that for directional fixed links, TPC is not required, conducted transmit power shall not exceed 30 dBm, and antenna gain is restricted to 23 dBi (maximum of 40W from the Canopy 5.7 and 5.8 GHz connectorized products). 10.2.12Brazil Notification Local regulations do not allow the use of 900 MHz, 2.4 GHz, or 5.2 GHz Canopy modules in Brazil. For compliant operation of an AP in the 5.8 GHz band, the Equivalent Isotropic Radiated Power from the built-in patch antenna and any associated reflector dish or LENS shall not exceed 36 dBm (4 W). When using the passive reflector (18 dB), transmitter output power must be configured no higher than 11 dBm. When using the LENS (10 dB at 5.8 GHz), transmitter output power must be configured no higher than 19 dBm. For compliant operation in the 5.4 GHz band, the Equivalent Isotropic Radiated Power from the built-in patch antenna and any associated reflector dish or LENS shall not exceed 30 dBm (1 W). When using the passive reflector (18 dB), transmitter output power must be configured no higher than 5 dBm. When using the LENS (9 dB at 5.4 GHz), transmitter output power must be configured no higher than 14 dBm. When not using the passive reflector or the LENS, the transmitter output power of the radio must be configured no higher than 23 dBm. The operator is responsible for enabling the DFS feature on any Canopy 5.4 GHz radio by setting the Region Code to “Brazil”, including after the module is reset to factory defaults. FCC Draft, November 2010 Page 37 Release 10.5 Release Notes and User Guide Supplement Important Note: This equipment operates as a secondary application, so it has no rights against harmful interference, even if generated by similar equipment, and cannot cause harmful interference on systems operating as primary applications. 10.2.13Australia Notification 900 MHz modules must be set to transmit and receive only on center channels of 920, 922, or 923 MHz so as to stay within the ACMA approved band of 915 MHz to 928 MHz for the class license and not interfere with other approved users. After taking into account antenna gain (in dBi), 900 MHz modules’ transmitter output power (in dBm) must be set to stay within the legal regulatory limit of 30 dBm (1 W) EIRP for this 900 MHz frequency band. 10.2.14Labeling and Disclosure Table for China The People’s Republic of China requires that Motorola’s products comply with China Management Methods (CMM) environmental regulations. (China Management Methods refers to the regulation Management Methods for Controlling Pollution by Electronic Information Products.) Two items are used to demonstrate compliance; the label and the disclosure table. The label is placed in a customer visible position on the product. Logo 1 means that the product contains no substances in excess of the maximum concentration value for materials identified in the China Management Methods regulation. Logo 2 means that the product may contain substances in excess of the maximum concentration value for materials identified in the China Management Methods regulation, and has an Environmental Friendly Use Period (EFUP) in years, fifty years in the example shown. Logo 1 Logo 2 The Environmental Friendly Use Period (EFUP) is the period (in years) during which the Toxic and Hazardous Substances (T&HS) contained in the Electronic Information Product (EIP) will not leak or mutate causing environmental pollution or bodily injury from the use of the EIP. The EFUP indicated by the Logo 2 label applies to a product and all its parts. Certain field-replaceable parts, such as battery modules, can have a different EFUP and are marked separately. The Disclosure table is intended to communicate compliance with only China requirements; it is not intended to communicate compliance with EU RoHS or any other environmental requirements. Table 12: China disclosure table 有毒有害物质或元素 部件名称 铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr6+) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 金属部件 × ○ × × ○ ○ 电路模块 × ○ × × ○ ○ 电缆及电缆组件 × ○ × × ○ ○ FCC Draft, November 2010 Page 38 Release 10.5 Release Notes and User Guide Supplement ○ 塑料和聚合物部件 ○ ○ ○ ○ × ○: 表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363-2006 标准规定的限量要求以下。 ×: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363-2006 标准规定的限量要求。 10.3 RF EXPOSURE SEPARATION DISTANCES To protect from overexposure to RF energy, install Canopy radios so as to provide and maintain the minimum separation distances from all persons shown in Table 13. Table 13: Exposure separation distances Module Type Separation Distance from Persons Canopy Module (FSK or OFDM) At least 20 cm (approx 8 in) Canopy Module with Reflector Dish At least 1.5 m (approx 5 ft) Canopy Module with LENS At least 50 cm (approx 20 in) 900 MHz, integrated or connectorized antenna At least 80 cm (32 in) Indoor 900 MHz SM At least 10 cm (4 in) The following section and its Table 14 provide details and discussion of the associated calculations. 10.3.1 Details of Exposure Separation Distances Calculations and Power Compliance Margins Limits and guidelines for RF exposure come from: US FCC limits for the general population. See the FCC web site at http://www.fcc.gov, and the policies, guidelines, and requirements in Part 1 of Title 47 of the Code of Federal Regulations, as well as the guidelines and suggestions for evaluating compliance in FCC OET Bulletin 65. Health Canada limits for the general population. See the Health Canada web site at http://www.hc-sc.gc.ca/rpb and Safety Code 6. ICNIRP (International Commission on Non-Ionizing Radiation Protection) guidelines for the general public. See the ICNIRP web site at http://www.icnirp.de/ and Guidelines for Limiting Exposure to Time-Varying Electric, Magnetic, and Electromagnetic Fields. The applicable power density exposure limits from the documents referenced above are 10 W/m for RF energy in the 5.7/5.8-GHz frequency bands. Peak power density in the far field of a radio frequency point source is calculated as follows: FCC Draft, November 2010 Page 39 Release 10.5 Release Notes and User Guide Supplement P"G S= 4 # d2 where S = power density in W/m P = RMS transmit power capability of the radio, in W G = total Tx gain as a factor, converted from dB d = distance from point source, in m d= Rearranging terms to solve for distance yields P"G 4# S Table 14 shows calculated minimum separation distances d, recommended distances and resulting power compliance margins for each frequency band and antenna combination. Table 14: Calculated exposure distances and power compliance margins Band Antenna 900 MHz FSK 2.4 GHz FSK 5.2 GHz FSK 5.4 GHz FSK Variable (calculated) Recommended Separation Distance Power Compliance Margin integrated 0.25 W (24 dBm) 15.8 (12 dB) 6 W/m 23 cm 80 cm (32 in) 12 external Yagi 0.063 W (18 dBm) 50.1 (17 dB) 6 W/m 20 cm 80 cm (32 in) 15 external flat panel 0.39 W (26 dBm) 10.0 (10 dB) 6 W/m 23 cm 80 cm (32 in) 12 indoor, integrated Simulation model used to estimate Specific Absorption Rate (SAR) levels 10 cm (4 in) integrated 0.34 W (25 dBm) 6.3 (8 dB) 10 W/m 13 cm 20 cm (8 in) 2.3 integrated plus reflector 0.34 W (25 dBm) 79.4 (19 dB) 10 W/m 46 cm 1.5 m (5 ft) 10 integrated 0.2 W (23 dBm) 5.0 (7 dB) 10 W/m 9 cm 20 cm (8 in) integrated plus reflector 0.0032 W (5 dBm) 316 (25 dB) 10 W/m 9 cm 1.5 m (5 ft) 279 integrated plus LENS 0.025 W (14 dBm) 40 (16 dB) 10 W/m 9 cm 50 cm (12 in) 31 integrated 0.2 W (23 dBm) 5.0 (7 dB) 10 W/m 9 cm 20 cm (8 in) integrated plus reflector 0.0032 W (5 dBm) 316 (25 dB) 10 W/m 9 cm 1.5 m (5 ft) 279 integrated plus LENS 0.020 W (13 dBm) 50 (17 dB) 10 W/m 9 cm 50 cm (12 in) 31 FCC Draft, November 2010 Page 40 Release 10.5 5.7 GHz FSK 5.4 GHz OFDM 5.8 GHz OFDM 4.9 GHz OFDM Release Notes and User Guide Supplement Integrated 0.2 W (23 dBm) 5.0 (7 dB) 10 W/m 9 cm 20 cm (8 in) integrated plus reflector 0.2 W (23 dBm) 316 (25 dB) 10 W/m 71 cm 1.5 m (5 ft) 4.5 integrated plus LENS 0.2 W (23 dBm) 50 (17 dB) W/m 28 cm 50 cm (20 in) 3.13 integrated SM, PMP 400, PTP 200 0.01 W (10 dBm) 50 (17 dB) 10 W/m 6 cm 20 cm (8 in) 10 Integrated SM, PMP 430 0.079 W (19 dBm) 10 (10 dB) 10 W/m 8 cm 20 cm (8 in) 6.4 connectorized AP, 18 dBi 0.02 W (13 dBm) 50 (17 dB) 10 W/m 9 cm 20 cm (8 in) integrated SM 0.079 W (19 dBm) 10 (10 dB) 10 W/m 8 cm 20 cm (8 in) 6.4 connectorized AP, 17 dBi 0.079 W (19 dBm) 40 (16 dB) 10 W/m 16 cm 80 cm (32 in) 25.6 Integrated, 17 dBi 0.063 W (18 dBm) 40 (16 dB) 10 W/m 14 cm 20 cm (8 in) connectorized, 18 dBi 0.063 W (18 dBm) 40 (16 dB) 10 W/m 14 cm 20 cm (8 in) The Recommended Separation Distance is chosen to give significant compliance margin in all cases. It is also chosen so that a given item (bare module, reflector, or LENS) always has the same distance, regardless of frequency band, to simplify remembering and following exposure distances in the field. These are conservative distances: They are along the beam direction (the direction of greatest energy). Exposure to the sides and back of the module is significantly less. They meet sustained exposure limits for the general population (not just short-term occupational exposure limits), with considerable margin. In the reflector cases, the calculated compliance distance d is greatly overestimated because the far-field equation models the reflector as a point source and neglects the physical dimension of the reflector. FCC Draft, November 2010 Page 41 Release 10.5 10.4 Release Notes and User Guide Supplement LEGAL NOTICES 10.4.1 Software License Terms and Conditions ONLY OPEN THE PACKAGE, OR USE THE SOFTWARE AND RELATED PRODUCT IF YOU ACCEPT THE TERMS OF THIS LICENSE. BY BREAKING THE SEAL ON THIS DISK KIT / CDROM, OR IF YOU USE THE SOFTWARE OR RELATED PRODUCT, YOU ACCEPT THE TERMS OF THIS LICENSE AGREEMENT. IF YOU DO NOT AGREE TO THESE TERMS, DO NOT USE THE SOFTWARE OR RELATED PRODUCT; INSTEAD, RETURN THE SOFTWARE TO PLACE OF PURCHASE FOR A FULL REFUND. THE FOLLOWING AGREEMENT IS A LEGAL AGREEMENT BETWEEN YOU (EITHER AN INDIVIDUAL OR ENTITY), AND MOTOROLA, INC. (FOR ITSELF AND ITS LICENSORS). THE RIGHT TO USE THIS PRODUCT IS LICENSED ONLY ON THE CONDITION THAT YOU AGREE TO THE FOLLOWING TERMS. Now, therefore, in consideration of the promises and mutual obligations contained herein, and for other good and valuable consideration, the receipt and sufficiency of which are hereby mutually acknowledged, you and Motorola agree as follows: Grant of License. Subject to the following terms and conditions, Motorola, Inc., grants to you a personal, revocable, non-assignable, non-transferable, non-exclusive and limited license to use on a single piece of equipment only one copy of the software contained on this disk (which may have been pre-loaded on the equipment)(Software). You may make two copies of the Software, but only for backup, archival, or disaster recovery purposes. On any copy you make of the Software, you must reproduce and include the copyright and other proprietary rights notice contained on the copy we have furnished you of the Software. Ownership. Motorola (or its supplier) retains all title, ownership and intellectual property rights to the Software and any copies, including translations, compilations, derivative works (including images) partial copies and portions of updated works. The Software is Motorola’s (or its supplier's) confidential proprietary information. This Software License Agreement does not convey to you any interest in or to the Software, but only a limited right of use. You agree not to disclose it or make it available to anyone without Motorola’s written authorization. You will exercise no less than reasonable care to protect the Software from unauthorized disclosure. You agree not to disassemble, decompile or reverse engineer, or create derivative works of the Software, except and only to the extent that such activity is expressly permitted by applicable law. Termination. This License is effective until terminated. This License will terminate immediately without notice from Motorola or judicial resolution if you fail to comply with any provision of this License. Upon such termination you must destroy the Software, all accompanying written materials and all copies thereof, and the sections entitled Limited Warranty, Limitation of Remedies and Damages, and General will survive any termination. Limited Warranty. Motorola warrants for a period of ninety (90) days from Motorola’s or its customer’s shipment of the Software to you that (i) the disk(s) on which the Software is recorded will be free from defects in materials and workmanship under normal use and (ii) the Software, under normal use, will perform substantially in accordance with Motorola’s published specifications for that release level of the Software. The written materials are provided "AS IS" and without warranty of any kind. Motorola's entire liability and your sole and exclusive remedy for any breach of the foregoing limited warranty will be, at Motorola's option, replacement of the disk(s), provision of downloadable patch or replacement code, or refund of the unused portion of your bargained for contractual benefit up to the amount paid for this Software License. THIS LIMITED WARRANTY IS THE ONLY WARRANTY PROVIDED BY MOTOROLA, AND MOTOROLA AND ITS LICENSORS EXPRESSLY DISCLAIM ALL OTHER WARRANTIES, EITHER EXPRESS OF IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. MOTOROLA DOES NOT WARRANT THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERRORFREE, OR THAT DEFECTS IN THE SOFTWARE WILL BE CORRECTED. NO ORAL OR WRITTEN REPRESENTATIONS MADE BY MOTOROLA OR AN AGENT THEREOF SHALL CREATE A WARRANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY. MOTOROLA DOES NOT WARRANT ANY SOFTWARE THAT HAS BEEN OPERATED IN EXCESS OF SPECIFICATIONS, DAMAGED, MISUSED, NEGLECTED, OR IMPROPERLY INSTALLED. BECAUSE SOME JURISDICTIONS DO NOT FCC Draft, November 2010 Page 42 Release 10.5 Release Notes and User Guide Supplement ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. Limitation of Remedies and Damages. Regardless of whether any remedy set forth herein fails of its essential purpose, IN NO EVENT SHALL MOTOROLA OR ANY OF THE LICENSORS, DIRECTORS, OFFICERS, EMPLOYEES OR AFFILIATES OF THE FOREGOING BE LIABLE TO YOU FOR ANY CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL OR SIMILAR DAMAGES WHATSOEVER (including, without limitation, damages for loss of business profits, business interruption, loss of business information and the like), whether foreseeable or unforeseeable, arising out of the use or inability to use the Software or accompanying written materials, regardless of the basis of the claim and even if Motorola or a Motorola representative has been advised of the possibility of such damage. Motorola's liability to you for direct damages for any cause whatsoever, regardless of the basis of the form of the action, will be limited to the price paid for the Software that caused the damages. THIS LIMITATION WILL NOT APPLY IN CASE OF PERSONAL INJURY ONLY WHERE AND TO THE EXTENT THAT APPLICABLE LAW REQUIRES SUCH LIABILITY. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU. Maintenance and Support. Motorola shall not be responsible for maintenance or support of the software. By accepting the license granted under this agreement, you agree that Motorola will be under no obligation to provide any support, maintenance or service in connection with the Software or any application developed by you. Any maintenance and support of the Related Product will be provided under the terms of the agreement for the Related Product. Transfer. In the case of software designed to operate on Motorola equipment, you may not transfer the Software to another party except: (1) if you are an end-user, when you are transferring the Software together with the Motorola equipment on which it operates; or 2) if you are a Motorola licensed distributor, when you are transferring the Software either together with such Motorola equipment or are transferring the Software as a licensed duly paid for upgrade, update, patch, new release, enhancement or replacement of a prior version of the Software. If you are a Motorola licensed distributor, when you are transferring the Software as permitted herein, you agree to transfer the Software with a license agreement having terms and conditions no less restrictive than those contained herein. You may transfer all other Software, not otherwise having an agreed restriction on transfer, to another party. However, all such transfers of Software are strictly subject to the conditions precedent that the other party agrees to accept the terms and conditions of this License, and you destroy any copy of the Software you do not transfer to that party. You may not sublicense or otherwise transfer, rent or lease the Software without our written consent. You may not transfer the Software in violation of any laws, regulations, export controls or economic sanctions imposed by the US Government. Right to Audit. Motorola shall have the right to audit annually, upon reasonable advance notice and during normal business hours, your records and accounts to determine compliance with the terms of this Agreement. Export Controls. You specifically acknowledge that the software may be subject to United States and other country export control laws. You shall comply strictly with all requirements of all applicable export control laws and regulations with respect to all such software and materials. US Government Users. If you are a US Government user, then the Software is provided with "RESTRICTED RIGHTS" as set forth in subparagraphs (c)(1) and (2) of the Commercial Computer Software-Restricted Rights clause at FAR 52 227-19 or subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013, as applicable. Disputes. You and Motorola hereby agree that any dispute, controversy or claim, except for any dispute, controversy or claim involving intellectual property, prior to initiation of any formal legal process, will be submitted for non-binding mediation, prior to initiation of any formal legal process. Cost of mediation will be shared equally. Nothing in this Section will prevent either party from resorting to judicial proceedings, if (i) good faith efforts to resolve the dispute under these procedures have been unsuccessful, (ii) the dispute, claim or controversy involves intellectual property, or (iii) interim relief from a court is necessary to prevent serious and irreparable injury to that party or to others. General. Illinois law governs this license. The terms of this license are supplemental to any written agreement executed by both parties regarding this subject and the Software Motorola is to license you under it, and supersedes all previous oral or written communications between us regarding the subject except for FCC Draft, November 2010 Page 43 Release 10.5 Release Notes and User Guide Supplement such executed agreement. It may not be modified or waived except in writing and signed by an officer or other authorized representative of each party. If any provision is held invalid, all other provisions shall remain valid, unless such invalidity would frustrate the purpose of our agreement. The failure of either party to enforce any rights granted hereunder or to take action against the other party in the event of any breach hereunder shall not be deemed a waiver by that party as to subsequent enforcement of rights or subsequent action in the event of future breaches. 10.4.2 Hardware Warranty in US Motorola US offers a warranty covering a period of 1 year from the date of purchase by the customer. If a product is found defective during the warranty period, Motorola will repair or replace the product with the same or a similar model, which may be a reconditioned unit, without charge for parts or labor. 10.5 LIMIT OF LIABILITY IN NO EVENT SHALL MOTOROLA BE LIABLE TO YOU OR ANY OTHER PARTY FOR ANY DIRECT, INDIRECT, GENERAL, SPECIAL, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY OR OTHER DAMAGE ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION OR ANY OTHER PECUNIARY LOSS, OR FROM ANY BREACH OF WARRANTY, EVEN IF MOTOROLA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. (Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you.) IN NO CASE SHALL MOTOROLA’S LIABILITY EXCEED THE AMOUNT YOU PAID FOR THE PRODUCT. FCC Draft, November 2010 Page 44
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 44 XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6 About : uuid:61170362-e8fd-11df-9253-002332ca4aba Keywords : Producer : Mac OS X 10.6.4 Quartz PDFContext Modify Date : 2010:11:05 11:54:39-05:00 Create Date : 2010:11:05 16:51:00Z Creator Tool : Microsoft Word Metadata Date : 2010:11:05 11:54:39-05:00 Document ID : uuid:4d44ad3a-e8fd-11df-9253-002332ca4aba Format : application/pdf Title : Release10.5FCCdraft2 Creator : John Harris Description : Author : John Harris Subject : Apple Keywords :EXIF Metadata provided by EXIF.tools