Motorola Solutions 92FT4887 RPX SERIES REPEATER User Manual 24019 A PORS en

Download:
Mirror Download [FCC.gov]
Document ID	1189439
Application ID	IyIeQayRuHfMpL4ho5yR2Q==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	295.72kB (3696528 bits)
Date Submitted	2009-10-27 00:00:00
Date Available	2009-12-11 00:00:00
Creation Date	2009-05-25 08:49:06
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2009-08-19 13:34:07
Document Title	24019_A_PORS_en.book
Document Creator	FrameMaker 7.2
Document Author:	mhdw87

Installation and User Guide
Models RPU2160/RPU4160
Document Copyrights
No duplication or distribution of this document or any portion thereof shall take place without the express
written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in
any form or by any means, electronic or mechanical, for any purpose without the express written
permission of Motorola.
Disclaimer
The information in this document is carefully examined, and is believed to be entirely reliable. However,
no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes
to any products herein to improve readability, function, or design. Motorola does not assume any liability
arising out of the applications or use of any product or circuit described herein; nor does it cover any
license under its patent rights nor the rights of others.
CONTENTS
Computer Software
Copyrights . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Radio Frequency (RF)
Exposure Safety Standards . . . . . . . . . . . . .v
Operational Safety
Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
FCC Licensing
Information. . . . . . . . . . . . . . . . . . . . . . . . . viii
Interference Information . . . . . . . . . . . . . . . viii
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .1
Package Contents . . . . . . . . . . . . . . . . . . . . . .1
About This Manual . . . . . . . . . . . . . . . . . . . . .2
Service Support. . . . . . . . . . . . . . . . . . . . . . . .2
Product Safety. . . . . . . . . . . . . . . . . . . . . . . . .2
Manual Revisions . . . . . . . . . . . . . . . . . . . . . .2
Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Repeater Overview . . . . . . . . . . . . . . . . . . . .3
Pre-Installation Considerations . . . . . . . . 10
RF Coverage Field Test. . . . . . . . . . . . .
Choosing a Tentative
Location . . . . . . . . . . . . . . . . . . . . . . . . .
Conducting the RF
Coverage Field Test . . . . . . . . . . . . . . .
Multiple Repeaters In A Single
Location (Multiple User Groups) . . . . . . . . .
Environmental Conditions at
Intended Installation Site(*) . . . . . . . . . .
Temperature Ranges . . . . . . . . . . . . . . .
Ventilation . . . . . . . . . . . . . . . . . . . . . . .
Electrical Requirements . . . . . . . . . . . . . . . .
AC/DC Power
Requirements . . . . . . . . . . . . . . . . . . . .
Site Grounding and
Lightning Protection . . . . . . . . . . . . . . . .
Electrical Ground . . . . . . . . . . . . . . . . . .
RF Ground . . . . . . . . . . . . . . . . . . . . . . .
Lightning Ground . . . . . . . . . . . . . . . . . .
10
11
12
13
14
15
15
16
16
16
16
17
17
CONTENTS
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
Parts of the Repeater . . . . . . . . . . . . . . . . . . . 3
Repeater Accessories . . . . . . . . . . . . . . . 5
How the Repeater Works. . . . . . . . . . . . . 8
CONTENTS
Repeater Installation . . . . . . . . . . . . . . . . . .18
Repeater Positioning
and Orientation . . . . . . . . . . . . . . . . . . . .18
Antenna Installation
Instructions . . . . . . . . . . . . . . . . . . . . . . .20
Installing External Antenna Using
the Antenna/Magnetic Mount /RF
Cable Kit Accessory . . . . . . . . . . . . . . . .22
RF Cable Installation. . . . . . . . . . . . . . . .24
Installing Exterior Antenna . . . . . . . . . . .25
Uninstalling Exterior Antenna . . . . . . . . .25
Wall Mount Installation
Instructions . . . . . . . . . . . . . . . . . . . . . . .25
AC/DC Power Supply
Connection . . . . . . . . . . . . . . . . . . . . . . .27
Outdoor Installations
Considerations . . . . . . . . . . . . . . . . . . . .28
Outdoors Repeater Temporary
Installation – Example. . . . . . . . . . . . . . .28
Vehicle Adaptor. . . . . . . . . . . . . . . . . . . .29
Alkaline Battery Frame . . . . . . . . . . . . . . . .30
About Alkaline Batteries . . . . . . . . . . . . . . . .30
Alkaline Batteries
ii
Frame Solution . . . . . . . . . . . . . . . . . . .
Alkaline Battery
Life Estimation . . . . . . . . . . . . . . . . . . . .
Alkaline Battery Power
LED (Side LED) . . . . . . . . . . . . . . . . . . .
Installing/Removing the
Alkaline Battery Frame . . . . . . . . . . . . .
Li-Ion Battery Frame
(Optional Accessory) . . . . . . . . . . . . . . . . . .
30
30
31
31
32
Getting Started . . . . . . . . . . . . . . . . . . . . . . 33
Turning Repeater On/Off . . . . . . . . . . . . . . .
Repeater Status Led
(Front LED) . . . . . . . . . . . . . . . . . . . . . . . . .
Radio LED Indicators . . . . . . . . . . . . . . .
Selecting A Channel. . . . . . . . . . . . . . . . . . .
Repeater Programming
Default Values . . . . . . . . . . . . . . . . . . . . . . .
33
33
33
35
37
Programming The Repeater . . . . . . . . . . . 38
Programming Features Overview . . . . . . . . 38
Programming the Repeater
Using the CPS . . . . . . . . . . . . . . . . . . . . 40
How to Read and
Modify Your Repeater’s
Features . . . . . . . . . . . . . . . . . . . . . . . . .41
Programming Your RDX
4 W Radios To Work With
The Repeaters. . . . . . . . . . . . . . . . . . . . . . . .43
Repeater Cloning. . . . . . . . . . . . . . . . . . . . .46
RDX Radio to Repeater
Cloning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Operating Instructions . . . . . . . . . . . . . . . . . .47
Cloning Instructions. . . . . . . . . . . . . . . . . . . .47
Troubleshooting . . . . . . . . . . . . . . . . . . . . .50
Use and Care . . . . . . . . . . . . . . . . . . . . . . . .53
Motorola Limited Warranty
for the United States
and Canada . . . . . . . . . . . . . . . . . . . . . . . . .54
Accessories . . . . . . . . . . . . . . . . . . . . . . . . .59
RPX Repeater
Series Accessories . . . . . . . . . . . . . . . . . . . .59
59
59
59
59
60
60
60
60
Appendix A: Repeater
Specifications. . . . . . . . . . . . . . . . . . . . . . . 61
Appendix B: Repeater
Lightning Protection . . . . . . . . . . . . . . . . . 69
How To Minimize Lightning
Damage for RPX Repeater
Series™ System. . . . . . . . . . . . . . . . . . . 69
AC Line
Requirements: . . . . . . . . . . . . . . . . . . . . 69
RF Protection
Instructions: . . . . . . . . . . . . . . . . . . . . . . 69
iii
CONTENTS
Programming Your
Radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Antenna Accessories . . . . . . . . . . . . . . . . .
Batteries Accessories. . . . . . . . . . . . . . . . . .
Power Supplies
Accessories . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Accessories . . . . . . . . . . . . . . . . . . .
RDX Pick-Up Radios and
Accessories . . . . . . . . . . . . . . . . . . . . . . . . .
Cables Accessories . . . . . . . . . . . . . . . . . . .
Charger Accessories . . . . . . . . . . . . . . . . . .
2-Way RDX Repeater
Capable UHFRadios . . . . . . . . . . . . . . . . . .
COMPUTER SOFTWARE
COPYRIGHTS
COMPUTER SOFTWARE
COPYRIGHTS
The Motorola products described in this
manual may include copyrighted Motorola
computer programs stored in semiconductor
memories or other media. Laws in the United
States and other countries preserve for
Motorola certain exclusive rights for
copyrighted computer programs, including, but
not limited to, the exclusive right to copy or
reproduce in any form the copyrighted
computer program. Accordingly, any
copyrighted Motorola computer programs
contained in the Motorola products described in
this manual may not be copied, reproduced,
modified, reverse-engineered, or distributed in
any manner without the express written
permission of Motorola.
iv
Furthermore, the purchase of Motorola
products shall not be deemed to grant either
directly or by implication, estoppels, or
otherwise, any license under the copyrights,
patents or patent applications of Motorola,
except for the normal non-exclusive license to
use that arises by operation of law in the sale of
a product.
RADIO FREQUENCY (RF)
EXPOSURE SAFETY
STANDARD
Caution
Before using this product, read
the operating instructions and
RF energy awareness
information contained in the
Product Safety and RF
Exposure booklet (Motorola
P/N 68007024074) enclosed
with your radio.
To ensure compliance to RF Energy Safety
Standards:
•
•
Install only Motorola approved antennas and
accessories
Be sure that Product Safety and RF Safety
Booklet (P/N 68007024074) enclosed with this
radio is available to the end user upon
completion of the installation of this radio
For a list of Motorola-approved antennas and other
accessories, visit the following web site which lists
approved accessories for your radio model:
http://www.motorola.com/RPX
SAFETY STANDARDS
SAFETY STANDARDS
OPERATIONAL SAFETY GUIDELINES
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with a damp cloth.
7.
Do not block any of the ventilation openings.
Install in accordance with the manufacturer’s
instructions.
8.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9.
Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the
third prong are provided for your safety. When
the provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
vi
10.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11.
Use only the attachments/accessories specified
by the manufacturer.
12.
Use only on a stable, flat surface or install using
the wall mount holster that comes with this
product. When a cart is used for transporting
this device, use caution when moving the cart/
apparatus combination in order to avoid injury
from tip-over.
13.
Unplug this apparatus during lightning storms or
when unused for long periods of time.
14.
Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
15.
The power supply is not suitable for outdoor
use. Use only in dry locations/conditions.
16.
Connect the power supply only to an
appropriately fused and wired supply of the
correct voltage (as specified on the product).
17.
Disconnect the power supply from the line
voltage by removing the main plug. The outlet
to which this equipment is connected should be
nearby and easily accessible.
18.
Maximum ambient temperature around the
power supply equipment must not exceed 40°C
(104°F).
19.
Make sure that the cord is located where it will
not be stepped on, tripped over, or subjected to
water, damage or stress.
SAFETY STANDARDS
vii
FCC LICENSING
INFORMATION
FCC Form 601 and Schedules D, H, and Remittance
Form 159.
FCC LICENSING
INFORMATION
INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC Rules.
Operation is subject to the condition that this device
does not cause harmful interference.
The RPX Repeater Series™ operate on radio
frequencies that are regulated by the Federal
Communications Commission (FCC). To transmit on
these frequencies, you are required to have a license
issued by the FCC. Application is made available on
Faxed contact the
Fax-On-Demand
system at:
1-202-418-0177
viii
When using portable hand held units with this
repeater, please note that there is an output power
limitation according to FCC's rule part 90.267. This
regulation limits the maximum output power of
portable units to 2 W when used with a repeater
operating on frequencies in the 450 – 470 MHz band
allocated for Industrial/Business use.
To obtain these FCC forms, request document
000601 which includes all forms and instructions. If
you wish to have the document faxed, mailed or have
questions, use the following contact information.
Mailed call the FCC forms hotline
at:
1-800-418-FORM
1-800-418-3676
For questions regarding FCC
license, contact the FCC at:
1-888-CALL-FCC
1-888-225-5322
Or: http://www.fcc.gov
Changes or modifications not expressly approved by
Motorola may void the user’s authority granted by the
FCC to operate this radio and should not be made. To
comply with FCC requirements, transmitter
adjustments should be made only by or under the
supervision of a person certified as technically
qualified to perform transmitter maintenance and
repairs in the private land mobile and fixed services as
certified by an organization representative of the user
of those services.
Replacement of any transmitter component (crystal,
semiconductor, etc.) not authorized by the FCC
equipment authorization for this radio could violate
FCC rules.
Use of this radio outside the country where it was
intended to be distributed is subject to government
regulations and may be prohibited.
ix
FCC LICENSING
INFORMATION
Before filling out your application, you must decide
which frequency(ies) you can operate on: “Appendix
A: Repeater Specifications” on page 61. For questions
on determining the radio frequency, call Motorola
Product Services at: 1-800-448-6686.
FCC LICENSING
INFORMATION
Notes
INTRODUCTION
Congratulations on your Motorola® RPX Repeater
Series™ purchase!
Note:
Read this user guide carefully to ensure
you know how to properly operate the
repeater before use.
Your product package contains the following products
and manuals:
•
Repeater (includes the Alkaline Battery Frame)
•
Antenna
•
Power Supply
•
Wall holster mount
•
User Guide, CD and Quick Reference Leaflet
•
Warranty Card
•
Product Safety & RF Exposure Booklet
For product information, visit us at:
www.motorola.com/radios/business
or visit our micro-site at: www.motorola.com/RPX
For User Guide or product-related questions, contact:
1-800-448- 6686 in the USA
1-800-461-4575 in Canada
1-866-522-5210 on your TTY (Text Telephone)
You can also send mail to us at:
Business Radios,
RPSD 1C15, Motorola
8000 West Sunrise Boulevard
Plantation, Florida 33322
INTRODUCTION
This repeater is a product of Motorola's 80 plus years
of experience as a world leader in the designing and
manufacturing of communications equipment. The
RPX Repeater Series™ provide cost-effective
communications for businesses such as retail stores,
restaurants, schools, construction sites,
manufacturing, property and hotel management and
more. Motorola Business Radios and Repeater
devices are the perfect communications solution for
all of today's fast-paced industries.
PACKAGE CONTENTS
ABOUT THIS MANUAL
ACRONYMS
This manual contains installation information required
for the RPX Repeater Series™ repeaters.
The explanations in this manual will be using the
following acronyms:
AC: Alternate Current
DC: Direct Current
RX: Receiving Frequency
TX: Transmitting Frequency
CX: Connected
DX: Disconnected
RF: Radio Frequency
P/N: Part Number
SERVICE SUPPORT
INTRODUCTION
For information related to the service support
(including software, replacement parts and
accessories for the RPX Repeater Series™), contact
your Motorola Authorized Distributors and Resellers
via MOL (Motorola On-Line Tool).
For all other inquiries about service information,
please call your Motorola Point of Contact or call:
1-800-448-6686 in the USA
1-800-461-4575 in Canada
1-866-522-5210 on your TTY (Text Telephone)
PRODUCT SAFETY
For information related to RF Exposure compliance
and Batteries and Chargers Safety, please refer to
“Radio Frequency (RF) Exposure Safety Standards”
on page v.
MANUAL REVISIONS
Changes may occur after this manual is printed. To
obtain an updated or latest version of this manual,
please go to: http://www.motorola.com/RPX
Table 1: RPX Repeater Series™ Models
Label
Model
RPU2160
RPU4160
Frequency Output Number of
Band
Power Channels
UHF
UHF
2W
4W
16
16
Battery
Default
Type
Alkaline
Alkaline
REPEATER OVERVIEW
PARTS OF THE REPEATER
Antenna
Connector
Status LED
Indicator
Channel
Knob
Battery Frame (*)
ON/OFF
Knob
Programming
Connector
Model Label
Power LED
Indicator
DC/AC
Connector
Dipole UHF Antenna
REPEATER OVERVIEW
(*) RPU4160 repeater model comes with standard Alkaline Battery Frame
AC/DC Power Supply
Wall Mount
Figure 1. Repeater Parts
Repeater Parts
The repeaters are compatible with 2 - way
repeater capable business radios. Please refer
to "Programming Your Radios” on page 43 for
more information on how to program the RDX
radios to work with the repeater. For RDX radio
model information details, please contact your
Motorola Point of Sale.
1.
5.
Use to indicate, among others, repeater’s
power up and transmission status. Please
refer to the "Getting Started” on page 33 for
more information.
6.
On/Off Knob
REPEATER OVERVIEW
English
Channel Selector Knob
Use to switch the repeater for up to 16
different channels. Please refer to "Getting
Started” on page 33 for more information.
3.
4.
7.
Model Label
Indicates the model of the repeater.
Antenna
Removable UHF 450 – 470 dipole antenna.
Please refer to "Repeater Installation” on
page 18 for more information.
Power LED Indicator
One side LED indicator gives repeater AC/
DC connection status whenever the repeater
is working on alkaline Battery Frame
(standard repeater model). Two LED side
indicators give AC/DC connection and
charging status whenever the repeater is
working on Li-Ion Battery Frame. Please
refer to "Alkaline Batteries Frame Solution”
on page 30 for more information.
Use to turn the repeater ON or OFF.
2.
Status LED Indicator
AC/DC Connector
Use to connect the AC/DC power supply.
8.
Programming Connector
Use to connect the repeater to a PC in order
to program. (CPS Programming Cable
(P/N RKN4155) required). Please refer to the
"Programming The Repeater” on page 38 for
more information.
9.
Alkaline Battery Frame
2.
Kit
The repeaters’ standard package includes
the Alkaline Battery frame. Refer to "Alkaline
Battery Frame” on page 30 for more
information.
10.
The repeaters’ accessories offers an
Antenna/Magnetic Mount/RF Cable Kit (P/N
HKKN4022). This external antenna
accessory is strongly recommended in order
to allow the repeater antenna to have a
better coverage. Please refer to "Repeater
Installation” on page 18 for more information.
Repeater Power Supply
The repeaters are equipped with AC/DC
power supply to connect the repeaters to AC
or DC power sources.
3.
Repeater Accessories
4.
Repeater Software (CPS)
The repeaters offer the convenient capability
of customizing your repeater features by
using the CPS (Computer Programming
Software). Please refer to the "Programming
The Repeater” on page 38 for more
information. For Software download
information, contact your Motorola Distributor
or Reseller.
REPEATER OVERVIEW
Lithium-Ion (Li-Ion) Battery Frame
Li-Ion Battery Frame (P/N HKHN4004A)
allows the use of high capacity Li-Ion
batteries in giving up to 16 hours of battery
back up operation.
Vehicle Car Power Supply Adaptor
For your convenience, the repeaters’
portfolio includes a Vehicle Adaptor (also
known as “Cigarette Lighter Adaptor” P/N
HKPN4003). Please refer to "Outdoor
Installations Considerations” on page 28 for
more information.
The repeaters include different types of
accessories that are sold separately. Please
refer to the "Accessories” on page 59 for more
information.
1.
Antenna, Magnetic Mount and RF Cable
Repeater General Applications
REPEATER OVERVIEW
The repeaters are ideal as a range extender, that
can help reach other users in areas that are
normally not covered by a 2-way radio’s range.
They are also very useful to help resolve the
common problem of the “dead spots” that are
created when there are terrain obstructions (like
hills or trees), concrete building structures or
architectural designs that interfere with the radio
signal(1).
English
The repeaters are designed to satisfy both 810 Mil
spec as well IP55 (*) level water and dust ingress
protection. This rugged device can stand harsh
environments(2) making it ideal for outdoors
operations. Its light weight and various back-up
power options (like alkaline/Li-Ion Batteries
Frames and Vehicle Adaptor) make this repeater a
perfect portable solution for temporary outdoor
applications.
The repeaters operate in the UHF 450 – 470 MHz
band providing 16 channels(3) with different preprogrammed settings. This particular feature
allows easy and quick in field repeater deployment
whenever there is need to setup more than one
repeater for different users’ groups.
Fully and easily programmable, the repeaters give
the flexibility to customize frequencies, codes and
other features according to specific needs(4).
A key advantage for the repeaters is that the
radios have been designed to be compatible with
the UHF RDX 2-way, repeater capable radios.
Enjoy the convenience of picking up RDX
accessories (high capacity batteries, chargers and
programming cables) and re-use them with your
repeaters. This clever inter operability feature will
allow you also to get the most out of your complete
radios and repeater system solution by offering
cloning and programming among radios and
repeaters.
.
Note:
Figure 2a. Repeater Application Example –
Indoors
(1) The repeaters work best when located in
an ideal place that can have good reception
for re-transmitting the signal without any
problems. Refer to "Pre-Installation
Considerations” on page 10 for more
information.
(2) The repeaters are not submersible
devices (Refer to "Appendix A: Repeater
Specifications” on page 61 for more
information) and it is NOT an FM (Factory
Mutual) certified device.
(4) The repeaters’ CPS software is required.
Refer to "Programming The Repeater” on
page 38 for more information.
Figure 2b. Repeater Application Example –
Outdoors
REPEATER OVERVIEW
(3) Out of the 16 pre-programmed channels
that are available out of the box, you can
select only ONE channel each time you TX/
RX with the repeater. The repeaters are NOT
multi-channel repeaters.
How the Repeater Works
The repeater allows 2-way radios, base stations
or call boxes to communicate through the
repeater in order to extend the coverage range
and/or overcome dead communication spots.
en
”f
TX
in
an
RX
in
qu
re
the
“
Y”
“X
fre
qu
en
cy
Repeater RX the “X” frequency from Paul
and re-TX it to Tom using “Y” frequency
Paul
Tom
REPEATER OVERVIEW
Figure 3a. How the Repeater Works (TX)
English
cy
en
”f
RX
Paul
in
an
qu
TX
in
re
the
“X
” fr
“Y
eq
ue
cy
Repeater RX the “X” frequency from Tom
and re-TX it to Paul using “Y” frequency
Tom
Figure 3b. How the Repeater Works (RX)
In the Figure 3a, the repeater will get the signal “X”
that Paul transmits from his radio and will convert
it into a “Y” frequency that will re-transmit to Tom.
In Figure 3b, when Tom answers back to Paul, his
radio will also use the “X” frequency to transmit.
The repeater will do the same frequency
conversion (“X” to “Y”) and will re-transmit it to
Paul using frequency “Y”.
Not only Paul and Tom will be able to
communicate using “X” and “Y” frequencies, but
so will all other 2-way, repeater capable radios that
may be in the area* working on those same
frequencies settings.
Note:
The repeater needs to re-transmit in a
different frequency from what it received in
order to avoid interferences.
The following are estimations of the repeaters’ talk
coverage range with the repeater located indoors.
Refer to Table 3 "Repeater Alkaline Frame Power
LED (Side) " on page 31 and "Figure 4. Estimated
Outdoors Coverage Range” on page 9 for more
information.
Table 2: Estimated Talk Range
Model
Industrial
Outdoors
Inside steel/concrete
industrial buildings
Line of sight/No
obstructions
UHF 2 W
Up to 420,000 square
feet
14 miles
UHF 4 W
Up to 600,000 square
feet
9 miles
As seen in Figure 4, the maximum antenna
height for low power fixed stations is limited to
23 meters (75 feet) above ground. For stations
operating at fixed locations for temporary
periods, the antenna height is limited to 7
meters (20 feet) above ground.
Note:
Note:
These are estimated maximum ranges that
assume ideal location, environmental and
terrain conditions for the repeater operation.
75 Ft
6 Miles
Max.
15 Miles Max.
for a
4W repeater.
Figure 4. Estimated Outdoors Coverage Range
REPEATER OVERVIEW
Repeater Antenna
Proper programming of the repeater (Refer
to "Programming The Repeater” on page 38
section for more information) and optimal
repeater antenna location are the most
important factors that will determine the
coverage and quality of your repeater
communications. It is highly recommended
to refer to "Pre-Installation Considerations”
on page 10 before proceeding to install the
repeater. Make sure your 2-way radios are
repeater capable (able to manage separate
TX and RX frequencies for the same
channel). Refer to "Programming The
Repeater” on page 38 for more information.
PRE-INSTALLATION
CONSIDERATIONS
RF Coverage Field Test
PRE-INSTALLATION
CONSIDERATIONS
Proper repeater installation ensures the best
possible performance and reliability of the
repeaters. Pre-installation planning is required to
make sure you take into account.
•
RF coverage field test to decide mounting
location of the repeater in relation to input
power and antennas
•
Site Environmental Conditions
•
Electrical Requirements
•
Proper programming of the repeater’s
parameters (in order to assure interoperability
with other radio devices).'Programming The
Repeater' on page 38 for more information.
Note:
The following instructions* are quick and easy tips
to test the RF coverage area and decide the best
position for the Repeater Antenna (either with the
antenna directly installed into the repeater device
or using the antenna/magnetic mount/ RF cable
accessory kit (P/N HKKN4022).
This field coverage test will need to be performed
by at least two people, each one with a fully
charged 2-way radio. Before the test, make sure
the radios are programmed exactly on the same
parameters (frequencies, codes, bandwidth, etc.)
and are operating in talk around mode.
Note:
(*) These instructions are not intended to
replace a professional RF field test.
You must read the entire pre-installation
chapter in order to assure proper repeater
operation.
10
Installation Guide
Choosing a Tentative Location
•
If you are planning to use the repeater to
cover a large area with different buildings, it is
•
Location should be as centered as possible to
line of sight (**) to most of the area to be
the area that is being intended for coverage
covered. Bear in mind that most of the times,
so the signal strength is at the same level as
increasing the repeater’s antenna height will
possible for all points.
improve the coverage, but is not necessarily
If the repeater is to be located inside a
always the case.
•
building, for example, try to look for a height
•
strongly recommended that you use the
antenna/magnetic mount and RF Cable
Accessory Kit to install the repeater antenna
in a high point that allows as much as possible
•
If you are planning to have an indoors
vertically centered location as well.
installation for the repeater, double check that
Location should meet minimum environmental
the environmental and electrical installation
requirements. (Please refer to 'Environmental
requirements described in the following
Conditions at Intended Installation Site(*)' on
sections are feasible.
page 14 for more information).
Note:
(**) Means sight from the repeater free of
obstructions at the naked eye.
Installation Guide
11
PRE-INSTALLATION
CONSIDERATIONS
Prior to the RF coverage field test, you must first
decide which would be the tentative locations for
the repeater. You should have different options
that will be evaluated according to the following
aspects:
PRE-INSTALLATION
CONSIDERATIONS
Conducting the RF Coverage Field Test
The objective of the field test is to “simulate” the
transmission quality and coverage that the
repeater may have based upon a chosen location.
This type of testing and planning becomes very
useful as it can save you extra work and money as
a poor location and/or adverse environmental
conditions can affect the repeater’s performance.
To do so, one person should remain in the
tentative repeater location and the second person
should start walking around the area intended to
be covered, while transmitting with the radio.
Figure 5: Conducting the RF Coverage
Field Test
If the quality communication between the two way
radios is good, this will mean that the repeater
transmissions should be OK.
The test can be conducted by more than two
people, as long as the first one remains fixed on
the repeater location under evaluation.
Note:
12
If you’re planning to have an external
antenna installation, you should try to mimic,
as much as possible, the antenna
positioning to replicate the antenna’s height.
Installation Guide
MULTIPLE REPEATERS IN A SINGLE
LOCATION (MULTIPLE USER
GROUPS)
As the repeaters have 16 different programmable
channels to choose from for setting up the TX/RX
frequency pairs, it is possible to configure multiple
repeaters in the same location or around the same
area.
Conduct the test transmitting preferably on those
settings that you will plan to have your radios and
repeater programmed(*). If possible, repeat the
test using different frequencies and codes.
Note:
30 ft m
30
(*) Remember TX range for the repeater is
450 – 455 MHz and RX range is 465 – 470
MHz.
If the reception coverage is below expectations, try
changing the height of the antenna or the repeater
location (do one change at a time so you can track
what is really affecting the coverage) and repeat
the field test coverage.
ft m
in.
in.
30
tm
in
Figure 6. Multiple Repeaters installations (One
User Group)
Installation Guide
13
PRE-INSTALLATION
CONSIDERATIONS
During this RF test coverage, one of the key field
conditions to test are those spots that will be the
most likely to be used for most of the people
(indoors and/or outdoors) and those that may
appear particularly challenging due to concrete/
steel walls, building architecture, obstructions (like
trees or vertical fire panels in ceilings or walls) and
terrain shape. Make sure you walk around all
those places in order to test reception and
transmission signal strength.
PRE-INSTALLATION
CONSIDERATIONS
Whenever you need to expand the 2-way radios’
coverage in the same area but for different user’s
groups, you can use multiple repeaters located at
the same site. For ensuring that the different
groups will not be interfering with each other and
that each one will have their private
communications, each repeater and the radios set
must have different channel settings (please refer
to 'Antenna Installation Instructions' on page 20
and 'Programming The Repeater' on page 38 for
more information). Additionally, for this case,
make sure the channel TX/RX frequency
separations between the different repeaters is at
least 1 MHz.
Note:
For other requirements (environmental,
electrical and mechanical), make sure you
read sections ahead, especially information
related to equipment ventilation.
14
Environmental Conditions at Intended
Installation Site(*)
A key factor for repeater performance is to
accurately evaluate the site environment where
the repeater will be installed. Plan the installation,
paying particular attention to environmental
conditions at the site like temperature, humidity,
dust and ventilation.
The repeater may be installed in any indoors
location suitable for electronic communications
equipment or outdoors temporary/semi-permanent
installations, provided that the environmental
conditions do not exceed the equipment
specifications for temperature, humidity, and air
quality according to Mil 810 and IP55 ruggedness
specifications (For specification details, please
refer to 'Appendix A: Repeater Specifications' on
page 61).
Installation Guide
Ventilation
Also important is to make sure that there is
adequate ventilation i.e. cabinets with ventilation
slots (for air circulation), especially if multiple
equipments are installed in the same room. In
which case, a minimum distance of open space
between the devices is recommended.
This temperature threshold applies both for
outdoors and indoors repeater operation.
Operating Temperature Range
Note:
-30°C (-22°F) to +60°C (+140°F)
(*) Please refer to 'Appendix A: Repeater
Specifications' on page 61 for specification
details.
Storage Temperature Range
-40°C (-40°F) to +85°C (+185°F)
Humidity & Water(*)
Do not to exceed 95% relative humidity (RH) @
(-30°C (-22°F) to +60°C (+140°F)).
Note:
The Repeaters are IP55 water resistant
devices, able to withstand water exposure
for certain periods of time. Bear in mind that
the repeaters are NOT submersible.
Installation Guide
15
PRE-INSTALLATION
CONSIDERATIONS
Temperature Ranges
This is the temperature measured in close
proximity to the repeater. For example, if the
repeater is mounted in a cabinet, the temperature
that is measured is within the cabinet.
Site Grounding and Lightning
Protection
PRE-INSTALLATION
CONSIDERATIONS
ELECTRICAL REQUIREMENTS
AC/DC Power Requirements
The repeater comes equipped with a AC/DC
power supply, that operates from 110 Vac to 240
Vac at 50 Hz to 60 Hz.
The outlet must be connected to an AC source
capable of supplying a maximum of 280 W. For a
nominal 110/120 Vac input, the AC source must be
able to supply 5 A and should be protected by
circuit breaker rated at 15 A. For a nominal 220/
240 Vac input, the AC source must be able to
supply 3 A and should be protected by a circuit
breaker rated at 10 A.
Caution
Proper site grounding and lightning
protection are vitally important
consideration, Failure to provide
proper lighting protection may result
in permanent damage to the
repeater equipment. Please refer to
'Appendix B: Repeater Lightning
Protection' on page 69 for basic
instruction.
The DC power requirement is 12 V (+/- 10%).
One of the most important considerations when
designing a communications site is the ground
and lightning protection system. Make sure
installations meet all local and state building codes
in you area.
Note:
Electrical Ground
The AC socket must be installed near the
equipment and must be easily accessible.
Consideration should be given to the
connection of the equipment to the supply
circuit and the effect that overloading of the
circuits might have on over current
protection and supply wiring. Appropriate
consideration of equipment ratings should
be used when addressing this concern.
16
Ground wires carrying electrical current from
circuitry or equipment at the site is included in the
category of electrical ground. Examples include
the AC or DC electrical power used to source
equipment located at the site, and wires or cables
connected to alarms or sensors located at the site.
Installation Guide
Lightning Ground
Providing adequate lightning protection is critical
to a safe reliable communications site. RF
transmission cables, and AC and DC power lines
must all be protected to prevent lightning energy
from entering the site building.
Although a comprehensive coverage of the site
grounding technique and lightning protection is not
within the scope of this instruction manual, there
are several excellent industry sources for rules
and guidelines on ground and lightning protection
at communications site.
Note:
Motorola recommends the following
reference source: “Motorola Quality
Standards Fixed Network Equipment
Installation Manual R56” P/N 6881089E50.
Installation Guide
17
PRE-INSTALLATION
CONSIDERATIONS
RF Ground
This type of ground is related to the transmission
of the radio frequency energy to earth ground. An
example of RF grounding is the use of shielding to
prevent or at least minimize the leakage of
unwanted RF transmissions from communications
equipment and cables.
REPEATER INSTALLATION
For the explanations in this chapter, please refer to
the “Parts of the Repeater” on page 3 under
“Repeater Overview” for more information.
REPEATER
INSTALLATION
Repeater Positioning and Orientation
Once you have decided the repeater’s location,
make sure you place it either on a flat and stable
surface (outdoors or indoors), lying horizontal as
shown in “Figure 7a. Repeater Orientation on a
Flat Surface” on page 18 and “Figure 7b.
Repeater Orientation Outdoors” on page 18 or
mount it on a flat wall/ceiling surface.
Figure 7a. Repeater Orientation on a Flat Surface
18
Figure 7b. Repeater Orientation Outdoors
The actual orientation of the repeater device itself
shouldn’t have any impact on the repeater’s
performance (given a non-obstructed antenna).
However, when using the dipole antenna (P/N
HKAE4000), make sure the antenna and power
supply are in a straight line (2 to 3 feet minimum)
as shown in “Figure 8a. Repeater Cable Layout
Using Dipole Antenna P/N HKAE4000” on
page 19. When using an external antenna
(Antenna/Magnetic Mount Kit – P/N HKKN4022),
make sure there is a minimum of 2 to 3 feet
distance for both the power cable and RF cable to
Installation Guide
run straight from the repeater in order to assure
that performance is not deteriorated as shown in
“Figure 8b. Repeater Cable Layout Using External
Antenna P/N HKKN4022” on page 19.
Note:
Double check that the Antenna’s cable
doesn’t tangle either around the repeater
device or the power supply. The power
supply cord also shouldn’t tangle around the
repeater device or antenna.
When positioning the repeater, make sure the
repeater antenna is placed away from
obstructions, metal structures or any objects or
enclosures (like elevators) that can cause any
type of shielding.
REPEATER
INSTALLATION
Power Supply
Cable
2 ft
Figure 8a. Repeater Cable Layout Using Dipole
Antenna P/N HKAE4000
Power Supply
Cable
2 ft
External Antenna
Cable
2 ft
Figure 8b. Repeater Cable Layout Using
External Antenna P/N HKKN4022
Installation Guide
19
Antenna Installation Instructions
1.
Repeater antenna installation is critical to the
system performance. The approved Motorola
antenna for the RPU4160 is the UHF Dipole
Antenna P/N HKAE4000, (50 Ohm).
Align the threaded end of the antenna with
the repeater’s antenna connector and turn
the antenna bushing clockwise to fasten it.
“Figure 9. Attaching Dipole Antenna to the
Repeater (clockwise)” on page 20.
REPEATER
INSTALLATION
Attaching the Dipole Antenna to
the Repeater
(Installing the dipole antenna directly onto the
repeater is recommended whenever coverage
range or obstructions are not an issue or/and the
repeater is likely to be moved around to other
sites).
Figure 9. Attaching Dipole Antenna to the
Repeater (clockwise)
20
Installation Guide
2.
Make sure the dipole antenna is mounted
vertically (90 degrees) in reference to earth
ground (either up or down). Please refer to
“Figure 10a. Examples of Correct Dipole
Antenna Orientation” on page 21 and “Figure
10b. Examples of Incorrect Dipole Antenna
Orientation” on page 21 for examples of
incorrect antenna positioning.
Ground
Figure 10b. Examples of Incorrect Dipole
Antenna Orientation
Removing the Dipole Antenna
from the Repeater
90º
Ground
Figure 10a. Examples of Correct Dipole
Antenna Orientation
Turn the antenna bushing counterclockwise until
you can remove it.
Installation Guide
21
REPEATER
INSTALLATION
90º
REPEATER
INSTALLATION
Installing External Antenna Using the
Antenna/Magnetic Mount /RF Cable Kit
Accessory
•
When installing the exterior antenna into the
magnetic mount, make sure the antenna is
always in a vertical orientation (either straight
up or straight down, 90° to ground). Avoid side
or skewed antenna orientations as these
positions can affect repeater performance
(See examples in “Figure 11a. Examples of
Correct Exterior Magnetic Mount Antenna
Orientation” on page 23 and “Figure 11b.
Examples of Incorrect Exterior Magnetic
Mount Antenna Orientation” on page 23).
•
Make sure the exterior antenna magnetic
mount is installed and positioned away from
obstructions like metal structures, concrete
walls or any other objects that may cause
signal shielding.
If as an outcome of the RF Coverage Test Field,
(please refer to “Pre-Installation Considerations”
on page 10) you decide that you will place the
repeater antenna somewhere else (outdoors or
indoors) away from the repeater device, you
should then use the Antenna/Magnetic Mount and
RF Cable accessory P/N HKKN4022.
Note:
Always use Motorola approved accessories
in order to assure performance and safety.
Please refer to “Accessories” on page 59 for
details.
Magnetic Mount Kit Installation
•
Ideally the external antenna magnetic mount
should be mounted on a metal surface or
other area with similar material that allows the
mount magnet to stick securely.
22
Installation Guide
90º
Ground
Ground
Figure 11a. Examples of Correct Exterior
Magnetic Mount Antenna Orientation
Figure 11b. Examples of Incorrect Exterior
Magnetic Mount Antenna Orientation
Installation Guide
23
REPEATER
INSTALLATION
90º
RF Cable Installation
REPEATER
INSTALLATION
Note:
When installing the RF cable make sure that:
The RF cable is 12 feet long. Keep this in
mind when locating the repeater.
In order to attach the RF Cable to the Repeater
(please refer to “Figure 12. Connecting RF Cable
to Repeater” on page 24), simply:
1.
Align the end of the RF Cable antenna
bushing with the repeater’s RF antenna
connector.
2.
•
The RF Cable is taut.
•
The RF Cable doesn’t go around the magnetic
mount antenna, antenna, the repeater device
or the power supply cable as all these can
cause electromagnetic interference (please
refer to “Figure 11a. Examples of Correct
Exterior Magnetic Mount Antenna Orientation”
on page 23 and “Figure 11b. Examples of
Incorrect Exterior Magnetic Mount Antenna
Orientation” on page 23 for examples of
wrong positioning).
•
If the cable is routed through a ceiling or wall
that connects outdoors, make sure there is an
appropriate sealing around the cable to
prevent water or other material from coming
permanently into the repeater.
Turn the RF Cable bushing clockwise to
fasten it.
Figure 12. Connecting RF Cable to Repeater
24
Important
Installation Guide
Do not attempt to modify the RF cable
from its original design in any way.
Installing Exterior Antenna
Uninstalling Exterior Antenna
In order to install the exterior antenna into the
magnetic mount, simply:
1.
1.
2.
Align the threaded end of the antenna with
the magnetic mount’s mini UHF connector as
shown on “Figure 13. Attaching Exterior
Antenna into Magnetic Mount” on page 25.
Turn counterclockwise in order to remove
antenna from magnetic mount.
It is important that all antenna cables
are grounded at the point they enter
the building.
Caution
Turn the antenna clockwise to fasten it.
The wall mount is recommended for permanent or
semi-permanent indoors repeater installation.
Figure 13. Attaching Exterior Antenna into
Magnetic Mount
Figure 14a. Wall Mount Holster
Installation Guide
25
REPEATER
INSTALLATION
Wall Mount Installation Instructions
To install the wall mount:
REPEATER
INSTALLATION
1.
The wall mount holster is designed to be
capable of mounting to a wall or any other
similar flat surface via screws, straps or
single bolt. (If you choose to use screws,
make sure you secure them tightly on each
one of the wall mount corners).
Remember not to install the repeater on
Important or near conductive or shielding
surfaces.
2.
3.
Once the wall mount is firmly secured to a
surface, slide the repeater device from top to
bottom of the holster (“Figure 14b. Installing
the Wall Mount Holster” on page 26) until the
repeater clicks in place into the wall mount
rails.
Figure 14b. Installing the Wall Mount Holster
Proceed to connect antenna and power
supply cables.
26
Installation Guide
AC/DC Power Supply Connection
To connect AC/DC power supply:
Each repeater ships standard with an AC/DC
Power supply cord (P/N PMPN4002A)(9 feet
long) that connects the repeater to a (110/120)/
(220/240) Vac source.
Important
When operating the power supply,
make sure that the maximum input
current never exceeds 0.8 Amp at 100
Vac and ambient temperature is
between -30°C to 60°C.
Provide over voltage/current protection
in order to avoid unsafe operating
conditions.
Note:
Plug the AC/DC power supply into an AC
power source of 110/220 V or a 12 V DC
power and route it to the Repeater Jack
labeled “AC/DC IN”.
The cable from the power supply should be
routed in a straight line and should not
tangle, go around or wrap around the
repeater device, the antenna or the RF
Cable. See “Figure 8a. Repeater Cable
Layout Using Dipole Antenna P/N
HKAE4000” on page 19 (Notice in this
picture that the cable must be laid down
straight for at least 2 feet).
Installation Guide
27
REPEATER
INSTALLATION
Nominal Input: (110/120)/(220/240) Vac at
60/50 Hz.
Average output voltage: 12 Vdc with 2.5 Amp (at
maximum load).
1.
Outdoor Installations Considerations
•
The RPX repeaters are suitable for temporary
outdoors operations under environmental
Note:
The ideal repeater outdoors usage features
the repeater working on back-up batteries.
(The power supply is not designed for
outdoor use).
conditions that meet the Mil Specifications 810
and IP55 (designed to meet level of water
ingress and dust protection). For details,
REPEATER
INSTALLATION
please refer to “Appendix A: Repeater
Specifications” on page 61.
Outdoors Repeater Temporary
Installation – Example
•
The repeater outdoors installation example in
“Figure 15a. Outdoors Temporary Repeater
Installation Example” on page 28 shows the
magnetic mount and RF cable installed on top
of the car’s roof in order to secure the antenna
against wind and allow repeater to be placed
inside the car. This is a convenient
configuration as the repeater can be protected
against harsh weather as well as re-charged
directly from the car battery * using vehicle
adaptor P/N HKPN4003, without interrupting
or reducing the repeater power output.
28
Figure 15a. Outdoors Temporary
Repeater Installation Example
Installation Guide
Vehicle Adaptor
The repeaters offer the convenience of a
Vehicle Adaptor accessory (P/N HKPN4003,
sold separately) for the repeaters.
REPEATER
INSTALLATION
Figure 15b. Vehicle Adaptor
Installation Guide
29
ALKALINE BATTERY FRAME
ABOUT ALKALINE BATTERIES
Please visit your Alkaline batteries’
manufacturer website for information and
guidelines regarding handling and disposal of
Alkaline batteries.
ALKALINE BATTERY
FRAME
Do not store alkaline batteries in a nonImportant operating equipment for longer than 30
days.
Alkaline Battery Life Estimation
When the repeater is working on back-up alkaline
batteries, the estimated battery life time (assumed
fully charged) is 16 hours for both 2 W and 4 W
models.
Alkaline Batteries Frame Solution
The repeaters’ standard package comes equipped
with an Alkaline Battery Frame Solution, (“Figure 16a.
Alkaline Battery Frame” on page 30 – alkaline
batteries are not included).
When the repeater is using the Alkaline batteries as
the backup power in the event of an AC/DC power
absence or failure and there is an AC/DC power
failure or absence, the repeater automatically
switches to back-up mode from the alkaline batteries.
30
Figure 16a. Alkaline Battery Frame
Whenever the 4 W repeater is switched to work
on battery back-up, the system will only
transmit at 2 W.
The 4 W repeater will automatically
switch to 2 W output power whenever it
Important detects that there is no AC/DC input. It
will then operate on back-up battery.
Installation Guide
Alkaline Battery Power LED (Side LED)
Important
Do not attempt to recharge alkaline
batteries. They are non-rechargable.
Table 3: Repeater Alkaline Frame Power LED (Side)
Status
LED Status
AC/DC
Status
Comments
Red
(Slow)
Blinking
CX
When the
battery frame is
empty or the
batteries are
dead
Batteries
Detected
Steady
Red
CX
Batteries are
good and in
place
OFF
OFF
DX
When AC/DC is
disconnected,
the LEDs will
be OFF
CX: Connected to AC/DC
Note:
1.
Turn OFF the repeater if it is turned ON.
2.
Disconnect AC/DC Power.
3.
Use a Phillips screwdriver to remove the four
corner screws located at each corner on the
back of the repeater, disconnect power
harness and lift away the repeater back
battery frame. “Figure 16b: Installing the
Alkaline Battery Frame into/from the
Repeater” on page 31.
DX: Disconnected from AC/DC
Alkaline Battery Frame is also available as a
stand-alone accessory (P/N HKHN4003).
Figure 16b: Installing the Alkaline Battery
Frame into/from the Repeater
Installation Guide
31
ALKALINE BATTERY
FRAME
No
Batteries
Detected
Installing/Removing the Alkaline
Battery Frame
4.
Arrange alkaline batteries to match each of
the alkaline frame batteries’ polarity (+ or -)
markings and slide them into each one of the
alkaline battery frame compartments. Repeat
until 12 batteries have been properly placed.
Plug in the power harness. “Figure 16c:
Installing the Alkaline Batteries” on page 32.
ALKALINE BATTERY
FRAME
Assemble the alkaline battery frame (loaded
with the alkaline batteries) into the back of
the repeater by tightening securely the four
screws on each of the four corners on the
back of the repeater. Please refer to “Figure
16b: Installing the Alkaline Battery Frame
into/from the Repeater” on page 31.
When securing back the alkaline frame
lid into the repeater, it is very important
to make sure the screws are tightened
Important
firmly to preserve the sealing of your
repeater. Failing to do so can negatively
impact the repeater’s IP55 water and
dust resistant feature.
LI-ION BATTERY FRAME (OPTIONAL
ACCESSORY)
Figure 16c: Installing the Alkaline Batteries
5.
6.
The repeaters are capable of operating with Li-Ion
batteries. The Li-Ion Battery Frame, P/N
HKHN4004 is sold separately as an accessory.
Make sure the repeater’s internal cable is
connected between the repeater and the
battery frame.
32
Installation Guide
Radio LED Indicators
TURNING REPEATER ON/OFF
Caution
1.
Table 4: Repeater Status LED Indicator
(Front LED)
MODE
Never transmit without having a
transmit antenna connected to the TX
antenna jack of the repeater.
Turn the ON/OFF knob clockwise to turn on
the repeater. The repeater front LED will
blink a red light for 3 seconds.
LED STATUS
Transmit
Solid Red
Receive (RX)
Solid Green
Idle
Red (Slow)
Blinking
Power Up
Solid Red 2 – 3
seconds
Transmit Low
Power
Solid Orange
REPEATER STATUS LED (FRONT LED)
Table 4 "Repeater Status LED Indicator (Front
LED) " on page 33 shows the repeater LED status
summary:
User Guide
33
GETTING STARTED
GETTING STARTED
GETTING STARTED
Table 4: Repeater Status LED Indicator
(Front LED) (Continued)
MODE
LED STATUS
Low Battery
Shutdown
Orange (Fast)
Blinking
Low Battery
Orange Blinking
Fatal Error at
Power Up
1 Green Blink, 1
Orange Blink, 1
Green Blink,
then repeat
Unprogrammed
Channel
Double Red
(Slow) Blinking
Non-Repeater
Channel Mode
1 Red Blink, 1
Green Blink,
then repeat
34
User Guide
SELECTING A CHANNEL
Transmit Band
450 – 455 Mhz
Channel
Common Parameters
Receive Band
465 – 470 Mhz–
Frequency
(TX) Index #
Frequency
(TX) Mhz
Code
(Index #)
Code
Value
(Hz)
Bandwidth
Frequency
(RX) Index
Frequency
(RX) Mhz
65
451.1875
67
12.5 KHz
34
466.0375
66
451.2375
77
12.5 KHz
35
466.0625
67
451.2875
88.5
12.5 KHz
36
466.0875
68
451.3375
29
179.9
12.5 KHz
37
466.1125
69
451.4375
none
12.5 KHz
38
466.1375
70
451.5375
67
12.5 KHz
39
466.1625
71
451.6375
82.5
12.5 KHz
40
466.1875
72
452.3125
10
94.8
12.5 KHz
41
466.2125
User Guide
35
GETTING STARTED
programmed Frequency, Interference Eliminator
Code and Bandwidth Settings. Please refer to the
The repeaters offer 16 different channels from
following table for factory default values details:
which you can choose ONE channel at a time for
the repeater to operate. To select a channel, rotate
the Channel Selector Knob until you reach the
desired channel. Each channel has its own preTable 5: Repeater Channels Default Settings
GETTING STARTED
Table 5: Repeater Channels Default Settings (Continued)
Transmit Band
450 – 455 Mhz
Channel
Common Parameters
Receive Band
465 – 470 Mhz–
Frequency
(TX) Index #
Frequency
(TX) Mhz
Code
(Index #)
Code
Value
(Hz)
Bandwidth
Frequency
(RX) Index
Frequency
(RX) Mhz
74
452.4125
29
179.9
12.5 KHz
42
466.2375
10
75
452.5125
12.5 KHz
50
467.8625
11
76
452.7625
74.4
12.5 KHz
51
467.8875
12
77
452.8625
79.7
12.5 KHz
52
467.9125
13
65
451.1875
85.4
12.5 KHz
53
469.4875
14
66
451.2375
91.5
12.5 KHz
54
469.5125
15
72
451.3125
11
97.4
12.5 KHz
55
469.5375
16
74
452.4125
13
103.5
12.5 KHz
56
469.5625
In order to modify these default values, you should use the CPS Software. Please refer to "Programming
The Repeater" on page 38 for more details.
36
User Guide
Table 6: Programmable Features Default Values
"Programmable Features Default Values" on
page 37 shows the default factory values that the
repeater has pre-programmed. These values can
only be customized by using the CPS software.
Repeater Features Default Values
Feature
Values
Default
TX Timeout
1, 2 or 3 minutes
1 minute
TX Hangtime
(or Carrier
Delay)
Off to 50 seconds
5 seconds
Courtesy Beep
ON or OFF
OFF
Repeater ID
15 minutes, 30
minutes, after TX
hangtime, or OFF
15 minutes
On Battery
Back-Up
OFF, 15 minutes, 30
minutes, 45
minutes, 60 minutes
30 minutes
Low Battery TX
0 to 255 minutes
10 minutes
Number of
Channels
1 to 16
16
Reverse Burst
180 to 240
180
TX Power
Low (2 W) or High
(4 W)
High – 4 W
TX BW
12.5 or 25.0 KHz
12.5 KHz
RX BW
12.5 or 25.0 Khz
12.5 KHz
User Guide
37
GETTING STARTED
REPEATER PROGRAMMING DEFAULT
VALUES
Please refer to the CPS software HELP File
(under “Content and Index”) where you will find
the details and explanations for each one of the
repeater’s programmable features.
PROGRAMMING THE
REPEATER
PROGRAMMING THE
REPEATER
PROGRAMMING FEATURES
OVERVIEW
The repeaters are fully programmable devices that
provide features customization by using the CPS*
(Computer Programming Software).
The CPS allows to program frequencies and
Codes (either from a pre-loaded frequency default
list table or allowing to enter directly any
customized value) as well as other features such
as Bandwidth, Hang Time-out, Repeater ID Timer,
Courtesy Beep timer, Transmit Time Out Timer,
Reverse Burst, among others.
One of the key advantages of the CPS is the
flexibility to quickly and easily program and clone
several repeaters using a customized profile. The
CPS also provides security by giving the option to
set up a codeplug password for profile repeater's
management (CPS Manager Lock).
38
User Guide
PROGRAMMING THE
REPEATER
Figure 17. Example of the CPS Repeater Interface
Note:
Contact your Motorola distributor or reseller in order to get information on how to get a copy of the CPS software.
User Guide
39
Programming the Repeater Using the
CPS
RP
CPS S X
oftwa
re
PROGRAMMING THE
REPEATER
Before you begin programming the repeater make
sure you have available:
•
A PC ( Windows® XP, Windows 2000 compatible,
Vista)
•
CPS Programming Cable (sold separately as an
accessory P/N RKN4155),
•
CPS* Software installed
•
Repeater batteries are charged or repeater is
connected to a AC/DC power line.
CPS Programming
Cable
To computer
USB Port
To repeater
programming
connector
Figure 18. Programming the Repeater
Using the CPS
Important
40
User Guide
Please notice that this CPS
Programming cable’s miniconnector should not be used for
connecting devices other than the
RDX Series chargers (RLN6304/
RLN6375) and the repeaters.
How to Read and Modify Your
Repeater’s Features
1.
7.
Ensure you have installed the latest CPS in
your computer.
Turn the repeater OFF.
3.
Plug the CPS Programming Cable P/N
RKN4155 into the Repeater’s programming
connector. “Figure 18. Programming the
Repeater Using the CPS” on page 40.
4.
Connect the other end of the CPS cable into
your computer ‘s USB port.
5.
Open your CPS software and turn your
repeater ON.
6.
Click “read” icon in the upper bar menu.
Note:
You will now be able to read and modify all
your repeater features with the options
available in the left side menu in your profile
window . For more details on how to read,
write or modify radio features, please refer
to the CPS Help Menu –> Content and
Index. Detailed information about how to
clone the repeater’s profile is also available
in the CPS Help Menu –> Content and
Index –> Cloning Repeaters.
The “read” icon is grayed-out until the
computer detects the CPS Programming
Cable.
User Guide
41
PROGRAMMING THE
REPEATER
2.
Note:
When the CPS reads the repeater
successfully, you will see a window pop up
showing a bar progress icon indicating the
repeater’s profile is being read.
CPS Connection Trouble Shooting
Table 7: Programming Mode: Trouble Shooting
PROGRAMMING THE
REPEATER
Symptom
Try This
CPS doesn’t read the
repeater or write to the
repeater
Make sure the CPS cable is securely connected on both ends
(programming port in the repeater and USB port in the computer)/Make sure
your repeater hasn’t run out completely of battery power or is connected to
an AC/DC supply/Make sure the CPS cable is not damaged.
CPS displays “Error:
Communication Error”
when trying to read or
write to the repeater
Make sure your repeater is ON/Double check that the repeater model
matches your CPS version and region as they should be compatible in order
to read and write. For checking your CPS version, click in the “about” icon in
the upper tool bar.
CPS displays “your
repeater doesn’t match
your region”
Double check that the radio model matches your CPS version and region as
they should be compatible in order to read or write. For checking your CPS
version, click on the “about” icon in the upper tool bar.
When trying to clone
the repeater, the CPS
displays an error or the
cloning fails
Please refer to “Cloning Repeaters” in the CPS Help File for details on
cloning details.
42
User Guide
PROGRAMMING YOUR
RADIOS
PROGRAMMING YOUR RDX 4 W
RADIOS TO WORK WITH THE
REPEATERS
RDX 4 W series radios are fully compatible with
your repeaters as they are of the same UHF band
and they support repeater capability features.
However, in order to configure the radios to
communicate with the repeater, there are basic
tips that you should take into account:
PROGRAMMING YOUR
RADIOS
User Guide
43
•
Make sure the channels in both the RDX radios and the repeaters that you want to use with the
PROGRAMMING YOUR
RADIOS
repeater capability are actually enabled in the CPS with a “check” box looking as follows:
Figure 19. Enabling Repeater capability settings
44
User Guide
•
Make sure the TX frequency and PL Code in
Note:
the radio channel that has been chosen for
repeater, is the same as the RX frequency in
the repeaters. Same for the RX frequency in
your RDX radio: make sure it matches the TX
frequency and PL code in the repeaters
channel.
•
Take into account that when matching
channel frequencies between the repeater
and the radios, you must also need to make
sure all other channel parameters (i.e.
codes, bandwidth and reverse burst) are at
the same correspondent values in order for
the radios-repeater communications to take
place properly.
The repeaters have 16 channels available,
each one with two TX/RX frequency pairs.
You can either use the repeater default
programmed frequencies and customize the
RDX channels to match the repeater’s or you
PROGRAMMING YOUR
RADIOS
can customize the repeater frequencies to
different frequencies pairs to match frequency
in the RDX radios.
User Guide
45
REPEATER CLONING
REPEATER CLONING
RDX RADIO TO REPEATER CLONING
To repeater
programming connector
R2R Cloning Cable
To RDX radio
charger mini-port
Figure 20. Cloning from an RDX radio into the Repeater
46
User Guide
OPERATING INSTRUCTIONS
•
Below are instructions on how to clone your RDX
2 W / 4 W radio into one of the repeaters.
CLONING INSTRUCTIONS
It is NOT possible to clone the repeaters into
the RDX radio.
The only parameters that can be cloned into the
Repeater are:
•
channel frequency,
•
code,
•
bandwidth,
•
power,
•
reverse burst,
•
scan list
•
the number of channels.
1.
Turn OFF both the radio and the repeater.
2.
Unplug any cables (power supply or USB
cables) from the Single Unit Charger.
3.
Plug one side of the cloning cable mini
connector to the Single Unit Charger. Plug
the other end to the Repeater programming
port connector.
Note:
Before you start the cloning process, make sure
you have the following components:
During the cloning process, no power is
being applied to the Single Unit Charger.
The batteries will not be charged. A data
communication is being established
between the repeater and the radio.
4.
Turn ON the repeater.
•
Fully charged batteries on both the RDX radio
and one of the repeaters
5.
•
One Single Unit Chargers (SUC) for the RDX
Radio (either P/N RLN6304 or RLN6175)
Power up the RDX radio following the
sequence below:
•
•
An RDX Radio to Radio (R2R) Cloning Cable
P/N RLN6303
•
Long press the PTT button and SB2
simultaneously while turning the radio ON.
Wait for 3 seconds before releasing the buttons
until a distinctive audible tone is heard.
User Guide
47
REPEATER CLONING
Note:
An RDX Radio, repeater capable
REPEATER CLONING
Note:
After cloning is completed, the RDX radio
will sound either a “pass” tone (cloning was
successful) or a “fail” tone (cloning process
has failed). The “pass” tone sounds like a
good key “chirp” whereas the “fail” tone
sounds similar to a “bonk” tone. If the RDX
radio is a display model, it will either show
“Pass” or “Fail” on the display (a tone will be
heard within 5 seconds).
6.
Once you have completed the cloning
process, turn the RDX radio OFF and ON to
exit ‘clone’ mode.
7.
Turn the repeater OFF and ON to exit “clone”
mode.
48
Important
User Guide
- If the RDX channels contains
frequencies that are not
within the repeater TX or RX
frequency range, the
repeater will not work on
these channels.
- In the RDX radio, make sure
that in each one of the TX/
RX frequency pairs, the
bandwidth setting has
exactly the same value. For
example, if in Channel 7 the
TX bandwidth separation is
12.5 KHz, then the
corresponding RX
bandwidth separation in this
same channel 7 should be
also 12.5 KHz.
WHAT TO DO IF CLONING FAILS
REPEATER CLONING
The radio will emit an audible “bonk” indicating
that the cloning process has failed. In the event
that cloning fails, try performing each of the
following tests before trying to start the cloning
process again:
1.
Ensure that the batteries on both radio and
repeater are fully charged.
2.
Check the cloning cable connection on both
ends.
3.
Ensure that the battery is engaged properly
on to the RDX radio.
4.
Ensure that the RDX radio is in cloning
mode.
5.
Ensure that the repeater is turned ON.
User Guide
49
TROUBLESHOOTING
TROUBLESHOOTING
Symptom
Try This...
No Power
Recharge or replace the Li-Ion battery. Replace AA batteries.
Reposition or replace AA batteries. Extreme operating
temperatures may affect battery life.
Verify repeater is connected to AC/DC.
Limited Talk Range
Steel and/or concrete structures, heavy foliage, buildings or
vehicles decrease range. Check for clear line of sight to improve
transmission. Verify repeaters and radios are correctly programed.
Transmissions are noisy
and not clear
Make sure the radios are set up to 12.5 KHz bandwidth. Repeater
is not fully compatible with radios using companding or set up at 25
KHz bandwidth.
50
User Guide
Try This... (Continued)
Message Are Not Received
Confirm that the radios have the same Channel, Frequency,
Interference Eliminator Code and Scramble Code settings and are
consistent with the Repeater’s settings. Verify the range coverage
is appropriate and there are no obstacles or shielding.
Heavy Static or
Interference
Radios are too close to repeater; they must be at least five feet
apart. Radios are too far apart from the repeater’s antenna. Double
check to make sure there are no obstacles interfering with
Low Batteries
Recharge or replace Li-Ion battery. Replace AA batteries. Extreme
operating temperatures affect battery life.
Li-On Power LED Light
Does Not Come On
Check if repeater’s batteries are properly inserted and/or check
battery/charger contacts to be sure they are clean and charging pin
is inserted correctly.
Low Battery LED Blinking
Although New Batteries
Are Installed
Verify that the radio is set to the correct battery type and is well
positioned into the battery frame according to instructions.
User Guide
51
TROUBLESHOOTING
Symptom
Symptom
TROUBLESHOOTING
Repeater Can’t Receive or
Can’t Re-transmit/Radio
Can Transmit But Can’t
Receive
Try This... (Continued)
Check repeater’s programming settings versus radio’s settings.
Check if the repeater is connected to the AC/DC power and is
Battery Does Not Charge
getting appropriate power. Check the charger LED indicators.
Although It Has Been
Change the Li-ON batteries using an external charger to see if the
Placed in the Li-On Battery
batteries are damaged. Make sure the operating temperatures are
Frame For A While
within specific ranges.
Note:
The RPX Repeater Series™ are designed with a companding feature that is compatible with Motorola 2way Business Radios. If you're working with a different radio and you experience static or noise in your
communications, double check that the radios are capable of companding.
52
User Guide
USE AND CARE
Use a soft damp cloth
to clean the exterior
Do not immerse
in water
Do not use alcohol or
cleaning solutions
If the repeater is submerged in water...
Dry with soft cloth
User Guide
USE AND CARE
Turn repeater OFF
and remove batteries
and antenna
Do not use repeater
until completely dry
53
WARRANTY
Products and Accessories
MOTOROLA LIMITED
WARRANTY FOR THE
UNITED STATES AND
CANADA
What Does this Warranty Cover?
Subject to the exclusions contained below,
Motorola, Inc. warrants its telephones, pagers, and
consumer and business two-way radios (excluding
commercial, government or industrial radios) that
operate via Family Radio Service or General
Mobile Radio Service, Motorola-branded or
certified accessories sold for use with these
Products (“Accessories”) and Motorola software
contained on CD-ROMs or other tangible media
and sold for use with these Products (“Software”)
to be free from defects in materials and
workmanship under normal consumer usage for
the period(s) outlined below.
This limited warranty is a consumer's exclusive
remedy, and applies as follows to new Motorola
Products, Accessories and Software purchased by
consumers in the United States, which are
accompanied by this written warranty.
54
Products Covered
Length of Coverage
Products and
Accessories as
defined above, unless
otherwise provided for
below.
One (1) year from the date
of purchase by the first
consumer purchaser of the
product unless otherwise
provided for below.
Decorative
Accessories and
Cases.
Decorative covers,
bezels, PhoneWrap™
covers and cases.
Limited lifetime warranty
for the lifetime of
ownership by the first
consumer purchaser of the
product.
Business Two-way
Radio Accessories
One (1) year from the date
of purchase by the first
consumer purchaser of the
product.
Products and
Accessories that are
Repaired or
Replaced.
The balance of the
original warranty or for
ninety (90) days from the
date returned to the
consumer, whichever is
longer.
User Guide
Exclusions
Use of Non-Motorola Products and
Accessories. Defects or damage that result from
the use of Non-Motorola branded or certified
Products, Accessories, Software or other
peripheral equipment are excluded from coverage.
Unauthorized Service or Modification. Defects
or damages resulting from service, testing,
adjustment, installation, maintenance, alteration,
or modification in any way by someone other than
Motorola, or its authorized service centers, are
excluded from coverage.
Altered Products. Products or Accessories with
(a) serial numbers or date tags that have been
removed, altered or obliterated; (b) broken seals
or that show evidence of tampering; (c)
mismatched board serial numbers; or (d)
nonconforming or non-Motorola housings, or
parts, are excluded form coverage.
User Guide
55
WARRANTY
Normal Wear and Tear. Periodic maintenance,
repair and replacement of parts due to normal
wear and tear are excluded from coverage.
Batteries. Only batteries whose fully charged
capacity falls below 80% of their rated capacity
and batteries that leak are covered by this limited
warranty.
Abuse & Misuse. Defects or damage that result
from: (a) improper operation, storage, misuse or
abuse, accident or neglect, such as physical
damage (cracks, scratches, etc.) to the surface of
the product resulting from misuse; (b) contact with
liquid, water, rain, extreme humidity or heavy
perspiration, sand, dirt or the like, extreme heat, or
food; (c) use of the Products or Accessories for
commercial purposes or subjecting the Product or
Accessory to abnormal usage or conditions; or (d)
other acts which are not the fault of Motorola, are
excluded from coverage.
WARRANTY
Communication Services. Defects, damages, or
the failure of Products, Accessories or Software
due to any communication service or signal you
may subscribe to or use with the Products
Accessories or Software is excluded from
coverage.
Software. Applies only
to physical defects in
the media that
embodies the copy of
the software (e.g. CDROM, or floppy disk).
Length of Coverage
WHAT WE WILL DO TO CORRECT
WARRANTY PROBLEMS
At no charge to you, we have the option to repair
or replace the Products or software that do not
conform to the warranty, or to refund the Products’
purchase price. We may use functionally
equivalent reconditioned/refurbished/pre-owned or
new Products or parts. No software updates are
provided.
Ninety (90) days from the
date of purchase.
Exclusions
Software Embodied in Physical Media. No
warranty is made that the software will meet your
requirements or will work in combination with any
hardware or software applications provided by
third parties, that the operation of the software
products will be uninterrupted or error free, or that
all defects in the software products will be
corrected.
56
WHO IS COVERED?
This warranty extends only to the first consumer
purchaser, and is not transferable.
Software
Products Covered
Software NOT Embodied in Physical Media.
Software that is not embodied in physical media
(e.g. software that is downloaded from the
internet), is provided “as is” and without warranty.
HOW TO OBTAIN WARRANTY SERVICE OR
OTHER INFORMATION?
Contact your Motorola point of purchase.
Please call:
1-800-448- 6686 in the USA
1-800-461-4575 in Canada
1-866-522-5210 on your TTY (Text Telephone)
User Guide
(e) your address and telephone number. If
requested, you must also return all detachable
parts such as antennas, batteries and chargers.
RETAIN YOUR ORIGINAL PROOF OF
PURCHASE.
We will ship repaired or replacement Products at
our expense for the freight and insurance, but at
your expense for any duties. If additional
information is needed, please contact us at the
telephone number listed above.
SOFTWARE COPYRIGHT NOTICE
The Motorola products described in this manual
may include copyrighted Motorola and third party
software stored in semiconductor memories or
other media. Laws in the United States and other
countries preserve for Motorola and third party
software providers certain exclusive rights for
copyrighted software, such as the exclusive rights
to distribute or reproduce the copyrighted
software. Accordingly, any copyrighted software
contained in the Motorola products may not be
modified, reverse-engineered, distributed, or
reproduced in any manner to the extent allowed by
law.
Furthermore, the purchase of the Motorola
products shall not be deemed to grant either
directly or by implication, estoppel, or otherwise,
any license under the copyrights, patents, or
patent applications of Motorola or any third party
software provider, except for the normal, nonexclusive, royalty-free license to use that arises by
operation of law in the sale of a product.
User Guide
57
WARRANTY
You will receive instructions on how to ship the
Products to Motorola. You must ship the Products
to us with freight, duties and insurance prepaid.
Along with the Products you must include:
(a) a copy of your receipt, bill of sale or other
comparable proof of purchase;
(b) a written description of the problem;
(c) the name of your service provider (if this
Product requires subscription service);
(d) the name and location of the installation facility
(if applicable) and, most importantly;
WARRANTY
PATENT NOTICE
EXPORT LAW ASSURANCES
This product is covered by one or more of the
following United States patents.
5896277 5894292 5864752 5699006 5742484
D408396 D399821 D387758 D389158 5894592
5893027 5789098 5734975 5861850 D395882
D383745 D389827 D389139 5929825 5926514
5953640 6071640 D413022 D416252 D416893
D433001
This product is controlled under the export
regulations of the United States of America. The
Governments of the United States of America may
restrict the exportation or re-exportation of this
product to certain destinations. For further
information contact the U.S. Department of
Commerce.
58
User Guide
POWER SUPPLIES ACCESSORIES
ACCESSORIES
Part No.
RPX REPEATER SERIES
ACCESSORIES
ANTENNA ACCESSORIES
Part No.
Description
Description
HKPN4003A
Cigarette Lighter Vehicle
Adaptor
TBD
AC/DC Repeater Power Supply
BATTERY ACCESSORIES
HKAE4000A
Dipole Antenna 438 – 470 MHz
Kit
BATTERIES ACCESSORIES
Part No.
Description
RLN6305
High Capacity Li-Ion Battery
2200 mAh
RLN6308
Ultra High Capacity Li-Ion
Battery 2400 mAh
RLN6351
Standard Li-Ion Battery
1100 mAh
Part No.
Description
HKHN4003A
RPX Repeater Series™
Alkaline Battery Frame
HKNN4010A
Ultra High Capacity Li-Ion
Battery CR Kit
RPX Repeater Series™ Li-On
Battery Frame
HKKN4011A
High Capacity Li-Ion Battery CR
Kit
HKHM4004A
User Guide
59
ACCESSORIES
HKKN4022A
Antenna with MAG Mount & 12
foot RF Cable Kit
RDX PICK-UP RADIOS AND
ACCESSORIES
2-WAY RDX REPEATER CAPABLE UHF
RADIOS
Part No.
CABLES ACCESSORIES
ACCESSORIES
Part No.
Description
RLN6303
Radio to Radio Cloning Cable
RKN4155
CPS USB Programming Cable
RDU4160d
RDX UHF 4 W CH 2-Way Radio
RDU4100
RDX UHF 4 W CH 2-Way Radio
CHARGER ACCESSORIES
Part No.
Description
RLN6304
Rapid Charger Kit
RLN6309
Multi-Unit Charger (MUC) Kit
RLN6175
Note:
60
Description
Standard Drop-in Tray Charger
For charging RDX radios and
stand-alone Li-Ion batteries only.
User Guide
APPENDIX A: REPEATER
SPECIFICATIONS
UHF 25 KHz
UHF 12.5 KHz
FCC Id
Product Specifications
TBD
TBD
IC Id
TBD
TBD
FCC Parts
Place Holder
TBD
14K8F3E
11K1F3E
Emission Designators
Operating RF Band (MHz)
450 – 470
10 – 20 MHz
(Programmable)
TX Frequency Band
450 – 455 Mhz
450 – 455 Mhz
RX Frequency Band
465 – 470 Mhz
465 – 470 Mhz
Channel Spacing (narrow and wide band)
25 KHz
12.5 KHz
Mode of Operation
Duplex
Duplex
Morse Code
Morse Code
1 (TX/RX) Channel
1 (TX/RX) Channel
16
16
Code Signalling
Number of Operating Channels
Number of Software Programmable Channels/
Knob Channels
Synthesized Steps
Tone/Code Signalling
1 Hz
1 Hz
Morse Code
Morse Code
User Guide
61
APPENDIX A: REPEATER
SPECIFICATIONS
450 – 470
10 – 20 MHz
(Programmable)
Frequency Separation
Product Specifications
UHF 25 KHz
UHF 12.5 KHz
2 W/4 W
2 W/4 W
Carrier Power Output (AC/DC) (Model Dependant)
Carrier Power Output on Batteries
Hang-Time Timer
Time-Out Timer
2W
2W
From 0 (OFF) to 50
seconds programmed
From 0 (OFF) to 50
seconds programmed
1, 2 or 3 minutes
1, 2 or 3 minutes
MIni UHF
MIni UHF
RF Connector
Cigarette Lighter Connector (Vehicle Adaptor)
APPENDIX A: REPEATER
SPECIFICATIONS
Antenna Impedance
Yes
Yes
50 Ohms
50 Ohms
Duty Cycle
100%
100%
PL Codes
39+ Programmable
39+ Programmable
DPL Codes
Input Voltage -– Repeater
Input Voltage -– Transceiver
84
84
110/220 Vac +/- 10%
110/220 Vac +/- 10%
12 Vdc +/- 10%
12 Vdc +/- 10%
230 mA
230 mA
30 mA
30 mA
Input Current Repeater (@100 Vac)
TX/RX
Standby
Input Current Transceiver (@ 12 Vdc)
TX/RX
Standby
62
User Guide
1.6 A
1.6 A
200 mA
200 mA
Product Specifications
UHF 25 KHz
UHF 12.5 KHz
450 – 455 Mhz
450 – 455 Mhz
High
4.0 W
4.0 W
Low
2.0 W
2.0 W
Transmitter
Frequency Range (MHz)
Carrier RF Output
Frequency Stability
Modulation
+/- 1.0 PPM (-300°C – 600°C) +/- 1.0 PPM (-300°C – 600°C)
Direct FM
Direct FM
± 5.0 kHz
± 5.0 kHz
Spurs & Harmonies (dBm)
< - 20 dBm
< -13 dBm
FM Hum & Noise
- 50 dB
- 50 dB
Adjacent Channel Power
60 dBc
60 dBc
< - 20 dBm
< -13 dBm
UHF 25 KHz
UHF 12.5 KHz
465 – 470 Mhz
465 – 470 Mhz
Programable
Programable
Radiated Spurious Emissions
Product Specifications
Receiver
Frequency Range (MHz)
Receiving System
User Guide
63
APPENDIX A: REPEATER
SPECIFICATIONS
Deviation (Modulation Limiting)
Product Specifications
Frequency Stability
Audio Frequency
Sensitivity (12 dB SINAD)
UHF 25 KHz
+/- 1.0 PPM (-300°C – 600°C) +/- 1.0 PPM (-300°C – 600°C)
300 Hz to 3 Khz
300 Hz to 3 Khz
- 119 dBm (0.25 uV)
- 119 dBm (0.25 uV)
Selectivity (Adjacent Channel Selectivity)
- 75 dB
- 70 dB
Intermodulation Rejection
- 70 dB
- 70 dB
Spurious Response Rejection (blocking 1 Mhz)
Radiated Spurious Emissions (< 1 GHz)
APPENDIX A: REPEATER
SPECIFICATIONS
UHF 12.5 KHz
- 90 dB
- 90 dB
- 54 dBm
- 54 dBm
Radiated Spurious Emissions (< 1 GHz)
- 52 dBm
- 52 dBm
Input impedance
50 Ohms
50 Ohms
810 Military Standards (1)
RPX Repeater 4 W –UHF 450 – 470 MHz
METHOD
PROCEDURE
810 - C
Low Pressure
500.1
High Temperature
501.1
1, 2
Low Temperature
502.1
Temperature Shock
503.1
Solar Radiation
505.1
64
User Guide
810 Military Standards (1)
RPX Repeater 4 W –UHF 450 – 470 MHz
METHOD
PROCEDURE
Rain
506.1
1, 2
Humidity
507.1
Salt Fog
509.1
Dust
510.1
Vibration
514.1
8, 10
Shock
516.1
1, 2, 5
810 - D
500.2
High Temperature
501.2
1, 2
1, 2
Low Temperature
502.2
Temperature Shock
503.2
Solar Radiation
505.2
Rain
506.2
1, 2
Humidity
507.2
2, 3
Salt Fog
509.2
Dust
510.2
Vibration
514.3
Shock
516.3
1, 4
User Guide
APPENDIX A: REPEATER
SPECIFICATIONS
Low Pressure
65
810 Military Standards (1)
RPX Repeater 4 W –UHF 450 – 470 MHz
METHOD
PROCEDURE
APPENDIX A: REPEATER
SPECIFICATIONS
810 - E
Low Pressure
500.3
High Temperature
501.3
1, 2
1, 2
Low Temperature
502.3
Temperature Shock
503.3
Solar Radiation
505.3
Rain
506.3
1, 2
Humidity
507.3
2, 3
Salt Fog
509.3
Dust
510.3
Vibration
514.4
Shock
516.4
1, 4
Other Product Specifications
Li-On Battery Solution
UHF 25 KHz
UHF 12.5 KHz
Available as an accessory
Available as an accessory
Alkaline Battery Frame Solution
Dimensions ( x W X D) (inches):
66
Yes
Yes
4.7 H x 7.4 W x 2.0 D
4.7 H x 7.4 W x 2.0 D
User Guide
Other Product Specifications
UHF 25 KHz
UHF 12.5 KHz
Repeater with Alkaline Frame
2.1 lbs
2.1 lbs
Repeater with Li-On Frame
2.0 lbs
2.0 lbs
16 Hours
16 Hours
Weight
Average Battery Life @ 100% duty
(20%/80% operation):
With Alkaline Frame
810 Military Standards (1)
RPX Repeater 4 W –UHF 450 – 470 MHz
METHOD
PROCEDURE
Low Pressure
500.4
High Temperature
501.4
1, 2
Low Temperature
501.4
1, 2
Temperature Shock
503.4
Solar Radiation
505.4
Rain
506.4
Humidity
507.4
Salt Fog
509.4
User Guide
APPENDIX A: REPEATER
SPECIFICATIONS
810 - C
67
810 Military Standards (1)
RPX Repeater 4 W –UHF 450 – 470 MHz
METHOD
PROCEDURE
Dust
510.4
Vibration
514.5
Shock
516.5
-30°C to + 60°C (Radio)
-30°C to + 60°C (Radio)
IP55
IP55
Environmental Specifications
Operating Temperature
APPENDIX A: REPEATER
SPECIFICATIONS
Sealing(2)
Shock & Vibration
Polycarbonate Housing passes EIA 603
Dust & Humidity (3)
Satisfied EIA 603
(1)
MIL STD 810 C, D, E, and F, have blowing rain of sections that call out the device shall survive subjection to 30
minutes of a 4 inch/hour in a 40 mph wind. Dust section calls out blowing dust around 11ug/m3 for 6 hours.
(2) IP55 means the enclosure is dust protected. It also means it is water protected as if jet of water were sprayed
by a hose ( 3 gal/min for at least 3 minutes).
(3) Relative Humidity (RH) is 95% at a -30°C to 60°C.
68
User Guide

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : FrameMaker 7.2
Modify Date                     : 2009:08:19 13:34:07-04:00
Create Date                     : 2009:05:25 08:49:06Z
Metadata Date                   : 2009:08:19 13:34:07-04:00
Format                          : application/pdf
Title                           : 24019_A_PORS_en.book
Creator                         : mhdw87
Document ID                     : uuid:80569cf6-02e1-47af-9572-06365ee2b7a5
Instance ID                     : uuid:9c69a260-97b7-410b-93de-763bed40e389
Has XFA                         : No
Page Count                      : 80
Author                          : mhdw87

EXIF Metadata provided by EXIF.tools