NCR RSD Atlanta 7710GA2 Electronic Pricing Transmitter User Manual Chapter 11
NCR Corporation, RSD - Atlanta Electronic Pricing Transmitter Chapter 11
Contents
- 1. Users Manual Cover
- 2. Users Manual Front
- 3. Users Manual Glossary
- 4. Users Manual Index
- 5. Users Manual Appendix A
- 6. Users Manual Appendix B
- 7. Users Manual Appedix C
- 8. Users Manual Appedix D
- 9. Chapter 1
- 10. Chapter 2
- 11. Chapter 3
- 12. Chapter 4
- 13. Chapter 5
- 14. Chapter 6
- 15. Chapter 7
- 16. Chapter 8
- 17. Chapter 9
- 18. Chapter 10
- 19. Chapter 11
- 20. Chapter 12
- 21. Chapter 13
Chapter 11
11 SmarTalker II and Rail Installation SmarTalker IIs This section provides information about SmarTalker IIs, rail and clip attachment, and SmarTalker II installation. The 8-character and 2x6-character SmarTalker II standard-size tags are the same size and both look like the following illustration. 16903 SmarTalker II, Standard Size The 2x4-character and 2x5-character SmarTalker II small-size tags are the same size and both look like the following illustration. 16912 SmarTalker II, Small Size The 2x4-character and 2x5-character SmarTalker II small-size tags are the same size and both look like the following illustration. 11-2 SmarTalker II and Rail Installation 17068 SmarTalker II, Signage Attaching the Bracket When installing a shelf rail, keep in mind that the viewing angle of SmarTalker II is very important. Your completed installation should provide the best combination of visibility and lack of glare. The following table provides optimum viewing angles for SmarTalker II tags. The angles are based an average person’s eye height of 1.59 m (62.6 in.) and average shelf-viewing distance of .91 m (36 in.). Shelf Height (in.) Optimum Angle Up (+) or Down (-) from Vertical 6.0 +57.0 12.0 +54.2 18.0 +51.0 24.0 +47.2 30.0 +42.7 36.0 +37.3 42.0 +30.9 48.0 +23.4 54.0 +14.8 60.0 +5.4 66.0 -4.2 72.0 -13.3 78.0 -21.5 84.0 -28.6 SmarTalker II and Rail Installation Tools for Each Installer Tape Measure, minimum length 25 ft. Large, wide-blade flat-head screwdriver with round (not square shank) 16 oz. Metal carpenter’s claw hammer (for hammering shelf rail pins) or fencing tool (an integrated hammer with nail pulling pliers) Nail pulling pliers or “nippers” (for shelf pin removal) Cloth or leather tool pouch with multiple pockets (for holding small shelf rail parts) Clamp with swivel pads (to hold rail to shelf) Knee Pads 1 pair Site Installation Tools Band saw* or Hacksaw (not a wood saw) Miter Box (for use with hacksaw) Utility Knife (for cleaning cut ends of shelf rails) Tools Per Store (for On-Going Maintenance) Band saw* or Hacksaw (not a wood saw) Miter Box (for use with hacksaw) Utility Knife Large, wide-blade flat-head screwdriver with round (not square) shank 16 oz. Metal carpenter’s claw hammer * A band saw is easier to use, but a hacksaw can be used instead. 11-3 11-4 SmarTalker II and Rail Installation Installing SmarTalker II Shelf Rails NCR representatives can direct you to third-party suppliers who can supply you with a wide variety of SmarTalker II shelf rails The following illustrations show some of the possibilities. SmarTalker II and Rail Installation Installing SmarTalker II C-channel Clips SmarTalker IIs (standard-size and small-size) can be installed into a clip that is installed on a shelf’s C-channel. The C-channel clip is available from NCR in three versions: 0 degrees, 25 degrees, and 40 degrees. The following illustrations show these clips. 16915 0-Degree C-channel Clip 16916 25-Degree C-channel Clip 16917 40-Degree C-channel Clip 11-5 11-6 SmarTalker II and Rail Installation To install a 0-degree, 25-degree, or 40-degree C-channel clip, place the appropriate notch in the clip onto the bottom lip of the C-channel and tighten the screw. The following illustration shows a 0-degree C-channel clip installed on a shelf’s C-channel. 16926 SmarTalker II and Rail Installation 11-7 Installing a SmarTalker II in a C-channel Clip To install a SmarTalker II in a C-channel clip, place the top of the tag into the top of the clip and press the bottom of the tag into the bottom of the clip until it snaps into place. 16927 To prevent theft, an optional security screw can be installed in the bottom of the clip as shown in the following illustration. 16928 The screw is a 2-56 x ¼” phillips pan-head, self-tapping screw that can be purchased from NCR. To remove a SmarTalker II from a C-channel clip, use a screwdriver to remove the optional security screw if it is installed, then use two fingers to push up the pawls on the back of the tag and the tag will pop out of the clip. 11-8 SmarTalker II and Rail Installation
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2001:06:11 10:33:19 Producer : Acrobat Distiller 4.0 for Windows Modify Date : 2001:06:11 10:33:21-04:00 Page Count : 8EXIF Metadata provided by EXIF.tools