NINGBO DOOYA MECHANIC and ELECTRONIC TECHNOLOGY DC146 Emitter User Manual

NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. Emitter

Users Manual

Download: NINGBO DOOYA MECHANIC and ELECTRONIC TECHNOLOGY DC146 Emitter User Manual
Mirror Download [FCC.gov]NINGBO DOOYA MECHANIC and ELECTRONIC TECHNOLOGY DC146 Emitter User Manual
Document ID1521815
Application IDTbCAuFoKV78MGw5QDgGsAA==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize20.58kB (257255 bits)
Date Submitted2011-08-11 00:00:00
Date Available2011-08-11 00:00:00
Creation Date2011-08-05 18:22:35
Producing SoftwareAcrobat Distiller 9.0.0 (Windows)
Document Lastmod2011-08-05 18:22:35
Document Titleuntitled
Document CreatorPScript5.dll Version 5.2.2
Document Author: june1

Set up and add emitter
Additional
Function
The display lamp of curtain
motor flashes a few times
and then goes out
DC146/DC147 special-purpose emitter for curtain motor
The curtain motor
are connecting
with the power
Press the set button
of curtain motor for
about 2S
The display lamp of the
curtain motor is constant
on,loosen the set button
of curtain motor
Press the emitter A way
curtain-close button once
Emitter A way programming
adding emitter set are finished
Version No: A 01
Special-purpose emitter for curtain motor
Cancel one channel of emitter
Additional
Function
DC146 single channel double way emitter
The display lamp of curtain
motor flashes a few times
and then goes out
DC147 five channels double way emitter
DC146 single channel double way emitter: A way and B way can be chosen,each way can
control one set curtain motor separately.A way and B way don`t interfere each other
The curtain motor
are connecting
with the power
Press the set button
of curtain motor for
about 2S
The display lamp of the
curtain motor is constant
on,loosen the set button
of curtain motor
DC147five channels double way emitter: Each channel had the same function with DC146.When pressing
channel-shift button and all the channel-shift display lamps light,that means the group control
status.Under the status of group control,Pressing A way buttons will start the group-control function of A
way,A way of all the channels will be availabe.Pressing B way buttons will start the group-control function
of B way,b way of all the channels will be availabe.
Press the emitter A way
curtain-open button once
Emitter A way cancelling is finished
Cancelling all emitters is finished
Additional
Function
The interval of reswitch on must
over 10 seconds
A way curtainclose button
A way curtainstop button
A way curtainopen button
Cancelling all emitters is finished
Switch off the power
for curtain motor
Press the set button of
curtain motor and don`t lossen
Swich on the power
of curtain motor
When the curtain motor
display lamp flashes several
times and then goes out,
loosen the set button
B way curtainclose button
B way curtainstop button
B way curtainopen button
B way set button(P2b)
A way set
button P2a
B way set
button P2b
The function of pulling and guiding by hand
Additional
Function
DC146
The curtain motor
are connecting
with the power
Pull once the curtain
by hand to the desired
derection
The curtain will move toward
the function automatically
Press the set button
of curtain motor for
about 2S
The display lamp of curtain
motor flashes a few times
and then goes out
Press the emitter A way
curtain-stop button once
Pull once the curtain
by hand to the desired
derection
The curtain is unmoved,
the function of pulling and
guiding by hand is closed
The backside of DC146
A way curtainclose button
A way curtainstop button
A way curtainopen button
The display lamp of the
curtain motor is constant
on,loosen the set button
of curtain motor
Repeat the above set,
the function of pulling
and guiding by hand will start
DC146
B way curtainclose button
B way curtainstop button
B way curtainopen button
Channel shift
button
Channel
display
OK
DC147
DC147
A way set
button P2a
B way set
button P2b
The backside of DC147
Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 this device may not cause harmful
interference, and 2 this device must accept any interference received, including interference that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio TV technician for help.
RF Exposure Statement
FCC RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure
condition without restriction.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : june1
Create Date                     : 2011:08:05 18:22:35+08:00
Modify Date                     : 2011:08:05 18:22:35+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Metadata Date                   : 2011:08:04 17:03:16+08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Document ID                     : uuid:CD73969778BEE01185A3915BB4271F39
Instance ID                     : uuid:2e0ba569-a56b-4e1c-8f49-0ca7e0c38b1a
Derived From Instance ID        : uuid:07a9d5b0-e746-4528-ae50-25035b30e253
Derived From Document ID        : uuid:cb5ce3a5-3122-4dd8-bdfa-015fda548896
Format                          : application/postscript
Title                           : untitled
Creator                         : june1
Page Count                      : 2
EXIF Metadata provided by EXIF.tools
FCC ID Filing: VYYDC146

Navigation menu