NINGBO DOOYA MECHANIC and ELECTRONIC TECHNOLOGY DV24CE DC Venetian Blinds Drive User Manual 123
NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. DC Venetian Blinds Drive 123
Manual
The he third limit position cancelled canccelled P2×1 ×1 Stop button×1 Run for hint DV24CE/L-0.6/34 DV24CEQ/L-0.6/34 Stop button×1 Run for Run hin nt hint OK Run for hint The third limit point cancelled ssuccessfully Blind Motor Specification Power on Delete limit Version NO. : A/00 Additional dditio onal function P2 1 P2×1 P2×1 2×1 Down 1 Down×1 Run for hin nt hint Run for hint Run for hint OK Technical support Technical support Effective transmitting distancemay have deviation due to actual environment Control range Technical support The limit is deleted Blind DV24CE/L Power on One motor maximum can store 20 channels, over 20 channels, if still need add new emitters, it will be repeating covered last channel. Repeat setting, function is cancelled Dot-move setting Additional function Up×1 ᴺ Please set the limit position before use. ᴻ When in the group control mode,the setting up,deleting programme,setting limit are unworkable. Down×1 Run for hint Run for hint OK Dot move setting is ok Power on P2×1 P2 2×1 P2×1 Run for hint L2 partition 200m 35m Emission frequency 433.92/868 MHz For the emitters without setting button like DC1650, you can press up button and stop button at the same time to work as the same function as setting button. Matchable emitter Run for hint Run for hint Run for hint P2×1 Run for hint DC313A 15-channel emitter DC1650 Single-channel emitter DC1651 Double-channel emitter DC1600 Single-channel emitter DC1602 15-channel emitter DC476A Portable 9-channel emitter DC1653 15-channel LCD emitter OK To clean up the emitter means deleting all the memory of emitter and limit switch in the motor receivers Stop Sto op button ×1 DC306A 5-channel emitter Run for hint Emittter Emitter adding addi ng is ok Delete elete emit emitter tterr P2×1 P2 2×1 DC305A Single-channel emitter P2×1 Power Pow wer on DC287 Single-channel emitter DC288 5-channel emitter DC289 15-channel emitter Button specification Technical support DC262 15-channel emitter DC316A Portable doublechannel emitter Press the set button on limit head once,the motor run upward,press the set button on limit head once,the motor will stop,press the set button on limit head again,the motor will run downward Long press the set button on limit head for more than 6s, the motor will run for hint,loose it, then motor direction has been changed with the same limits as before; Long press the set button on limit head for more than 11s, the motor will run for hint,loose it, then it will delete every memory and restore the factory settings; Power connector OK The emitters all deleted Power on L1 open Emitter a is the one already matched code, while emitter b has not Add dd Emitterr Additional function 12V Technical support Additional function L1 L2 P2×1 Run for hint Blind Up Stop Down E:Electronic Electronic limit + Built-in receiver The program button Setting button (P2) A Installation of the motor Additional function Setting up During the settings, the time between two operation must be shorter than 10s, otherwise it will To exit the setting. If the motor already experienced experience match code, the memory will be cleared if do d it again Up×1 Additional function Run for hint T˚10s ROPE WINDER Switch off Run for hint Switch on OK P2×1 P2×1 Set up is ok. The up limit button control the motor clockwise. Run for hint Down×1 DS391 Run for hint DRIVE-SHAFT WALL BRACKET After switch tch on, press on se setting etting button of the motorr 2s, the motor w will ill run for hint U-SHAPE GROOVE DC VENETIAN BLINDS DRIVE DV24CE/L U-SHAPE PLATE Repeat the e reverse rev verse of direction setting operation, the direction on of o motor can be reverted re everted in a loop The rever reverse rsse of direction n setting Additional onal function Up button×1 OK Set up is ok. The down limit button control the motor clockwise. Stop button×1 Up button×1 g button Setting ×5s Run for hint OK VENETIAN BLINDS essful change Successful the direction VENETIAN BOTTOM BEAM Power ower on Additionall function Rechargeable Description Additional function )᷊ ttery 12V Ba 224(A le᷉DC Po The motor will stop Set up / down limit posi po tion position The motor runs upword The motor runs downword ① It is inv valid d when the up limit and me location invalid down limit are at the same to limit set; ② Must ccomplete omp plete the down limit point ③ After limit limit setting,with setting with power and memory function; ᴺIn the process of adjusting the up / down limit: when the motor moving up or down, dow wn, press press the setting button once, the motor will be e under the step-moving status,press the e setting button again to quit the step-moving step-m moving status stttatus ᴻTh The he step-moving status: themotor will run up or down down by the way of step-moving so that the limit position can be adjusted more e correctly ᴺDV24DE can be charged by the charger DC240I(J/K) or the motor can get the power from the 12V battery pole; We have two types of battery pole,they are DC224 and DC224A (rechargeable) ᴻDC224A is rechargeable by solar panel DC683B or charger Dc520. P2×1 2× ×1 P2×1 2×1 Up×1 Run for hint Run for hint Up×1 Stop×1 The up limit point Run for hint Confirm the Blind to stop in the up limit position Power on Stop×5 Down×1 The motor stops Stop×5 Stop×1 Run for hint Run for hint The down limit point DC224A Confirm the the Blind Blind to stop in n the th he down limit limi position position po DC520 DC224A DC240I(J/K) DC683B The up limit position The down limit position The e motor stops ᴺAfte ᴺ After er the up limit and down limit lim mit setting, you can set the the third third limit point between betwe een them m as a the half ha alf open position po ᴻ will be cancelled can nce elled as the the cancellation cancella ᴻThe third limit point will of limit limiit and code matching The third limit position setting ti Additional function The third limit position tion setting Stop×1 P2×1 Stop×1 Run for hint The third limit position (any position) Already set up, down limit position The motor stops OK Setting is ok Run for hint Stop×1 Run for hint OK The third limit sett point setting successfully successful FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : Administrator Create Date : 2015:06:11 11:03:42+08:00 Modify Date : 2015:06:11 11:05:17+08:00 Subject : Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Format : application/pdf Creator : Administrator Description : Title : 123.pdf Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2015:06:11 11:05:17+08:00 Keywords : Producer : Acrobat Distiller 9.0.0 (Windows) Document ID : uuid:bff13562-d415-4c9f-ae20-f493c9abc1e3 Instance ID : uuid:2817f2ba-53c3-43b2-b6bb-d4c9ee385a0b Page Count : 3EXIF Metadata provided by EXIF.tools