Nedap N V UPASSACC UHF RFID reader User Manual uPASS Access
N. V. Nederlandsche Apparatenfabriek NEDAP UHF RFID reader uPASS Access
13_uPassAccess_InstallGuide_E CGDUPASSACC
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1931395 |
| Application ID | 5tADE6Y/EZKXdqT/ZI0qHQ== |
| Document Description | 13_uPassAccess_InstallGuide_E CGDUPASSACC |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 28.95kB (361873 bits) |
| Date Submitted | 2013-04-03 00:00:00 |
| Date Available | 2013-04-03 00:00:00 |
| Creation Date | 2013-03-18 15:15:08 |
| Producing Software | Adobe PDF Library 9.0 |
| Document Lastmod | 2013-03-18 15:15:57 |
| Document Title | uPASS Access |
| Document Creator | Acrobat PDFMaker 9.1 for Word |
| Document Author: | Hans Rappard |
uPASS Access Installation Guide 2013-03-18 Doc.no. 5281326 This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys no license under any patent or other right, nor does the publisher assume liability for any consequence of its use; specifications and availability of goods mentioned in it are subject to change without notice; it is not to be reproduced in any way, in whole or in part, without the written consent of the publisher. © Nedap AVI Page 1 of 19 uPASS Access FCC ID: CGDUPASSACC IC: 1444A-UPASSACC Compliace statement: This device complies with part 15 of the FCC rules and to RSS210 of Industrial Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Déclaration conformitè: Cet appareil se conforme aux normes RSS210 exemptés de license du Industry Canada. L'opération est soumis aux deux conditions suivantes: (1) cet appareil ne doit causer aucune interférence, et (2) cet appareil doit accepter n'importe quelle interférence, y inclus interférence qui peut causer une opération non pas voulu de cet appareil. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device shall be installed to provide a separation distance of at least 20 cm from all persons. © Nedap AVI Page 2 of 19 uPASS Access CONTENTS INTRODUCTION .......................................................................................................................................................................................4 SUPPORTED TAGS ........................................................................................................................................................................4 1.1 TAG SECURITY ...............................................................................................................................................................................5 1.2 INSTALLATION .........................................................................................................................................................................................6 SAFETY INSTRUCTION ................................................................................................................................................................6 2.1 MOUNTING INSTRUCTIONS...................................................................................................................................................... 6 2.2 CONNECTIONS .........................................................................................................................................................................................8 POWER SUPPLY .............................................................................................................................................................................9 3.1 COMMUNICATION .......................................................................................................................................................................9 3.2 RS485 ..................................................................................................................................................................................9 3.2.1 USB .......................................................................................................................................................................................9 3.2.2 WIEGAND / MAGSTRIPE ............................................................................................................................................ 10 3.2.3 LED CONTROL ............................................................................................................................................................................. 11 3.3 TAMPER SWITCH........................................................................................................................................................................ 11 3.4 NEDAP ANTENNA INTERFACE .............................................................................................................................................. 11 3.5 UHF FREQUENCIES .............................................................................................................................................................................. 12 RADIO REGULATIONS .............................................................................................................................................................. 12 4.1 FREQUENCY CHANNEL SELECTION .................................................................................................................................... 12 4.2 READER CONFIGURATION ................................................................................................................................................................ 13 UHFTOOL SOFTWARE .............................................................................................................................................................. 13 5.1 SETTINGS ...................................................................................................................................................................................... 13 5.2 READ DATA .................................................................................................................................................................... 13 5.2.1 DECODE NEDAP XS ..................................................................................................................................................... 14 5.2.2 RELAY / TIMING ............................................................................................................................................................ 15 5.2.3 LED CONTROL ............................................................................................................................................................... 15 5.2.4 EXPERT SETTINGS ...................................................................................................................................................................... 16 5.3 OUTPUT ........................................................................................................................................................................... 16 5.3.1 OUTPUT MESSAGE FORMAT ................................................................................................................................... 16 5.3.2 EXTRA OUTPUT ............................................................................................................................................................ 17 5.3.3 FREQUENCY ................................................................................................................................................................... 18 5.3.4 READ RANGE ................................................................................................................................................................. 18 5.3.5 TECHNICAL SPECIFICATIONS .......................................................................................................................................................... 19 PART NUMBERS .................................................................................................................................................................................... 19 © Nedap AVI Page 3 of 19 uPASS Access 1 INTRODUCTION The uPASS Access reader offers a revolutionary and enduring solution for hands-free door access. The uPASS Access has the dimensions of a conventionally access control reader but offers read range unmatched in the industry. The uPASS Access offers identification up to 2 meter (6 feet) using the latest UHF technology. The uPASS Access includes a RS485 interface, a wiegand/magstripe and a RF-modulation interface. The uPASS Access can also be connected to NEDAP AEOS access control hardware such as the AP1001, using the RF-modulation interface. The uPASS Access does not offer the TRANSIT compatibility features. The uPASS Access is equipped with a fixed shielded cable pigtail, 12 x 0.14 mm2, length 5 meter (15 feet). The cable shield shall be connected to the metal case of the external device or external devices. In the case of extending this pigtail cable, ONLY shielded cables shall be used and all shields shall be connected to the metal case of the external device(s). 1.1 SUPPORTED TAGS Any EPC Class 1 Gen 2 tag is supported by the uPASS Access. NEDAP formatted UHF tags can have the following formats: • NEDAP UHF wiegand tags These tags will contain all wiegand information including facility code and parity bits. All wiegand formats can be supported. The reader transparently sends this information via the wiegand outputs. There is no need to change any DIP-switches or configuration settings. See chapter 3.2.3 for wiring details. Note: The Wiegand output format is determined by the tag and not by the reader. • NEDAP UHF magstripe tags These tags will contain all magstripe information. The reader transparently sends this information onto the magstripe interface. There is no need to change any DIP-switches or configuration settings. See chapter 3.2.3 for wiring details. Note: The magstripe output format is determined by the tag and not by the reader. • NEDAP UHF XS tag These tags are especially programmed in the same format as our 2.45GHz AVI tags (Compact-Tag, WindowButton and Heavy-Duty-Tag). The tags will also have a customer-code and id-number. The reader will modulate the tag-info onto the Nedap antenna interface output, which can be connected to NEDAP AEOS access control hardware such as the AP1001. Note: See also the 'decode nedap xs' feature as described in chapter 5.2.2. © Nedap AVI Page 4 of 19 uPASS Access 1.2 TAG SECURITY EPC (Electronic Product Code) tags were introduced as a possible successor to the barcode with added functionalities. The tag emits its EPC in plain text. This makes the tags vulnerable to cloning and counterfeiting attacks. Unlike many 13MHz smartcards, EPC tags do not support any DES, 3DES or AES encryption. EPC tags contain a data field known as the Tag Identifier (TID). At the discretion of the EPC manufacturer, the value may be factory programmed and locked, ensuring that tags have a unique identity and (theoretically) cannot be cross-copied. This TID based anti-cloning mechanism is not considered to be a strong protection. NEDAP UHF tags support a locked serialized TID and the uPASS Access reader can be configured to read the TID data field. In addition NEDAP has also implemented an advanced anti-cloning and anti-counterfeiting method based upon a two way authentication. This feature is supported in combination with all NEDAP UHF tags. By default the uPASS Access reader is configured to read any EPC tag. We encourage customers to enable the TID-check or the two way authentication. But also advise not to completely rely on these methods in high-security applications. © Nedap AVI Page 5 of 19 uPASS Access 2 INSTALLATION 2.1 SAFETY INSTRUCTION The following safety precautions should be observed during normal use, service and repair. • • • • 2.2 The uPASS Access may only be installed and serviced by qualified service personnel. Disconnect the power supply before (dis)connecting any wires, uPASS Access is NOT hot-swappable, so when making or changing connections, power must be switched OFF. The cable shield shall be connected with safety ground and the metal case of the external device(s). To be sure of safety, do not modify or add anything to the uPASS Access other than mentioned in this installation guide or indicated by NEDAP N.V. MOUNTING INSTRUCTIONS The uPASS Access can be mounted to any surface, including directly to metal. See the picture below for details about the dimensions. Figure 1: uPASS Access dimensions (mm) Mount the base-plate on the required location. Ensure that it is placed correctly covering the cable entry hole. Properly fix the base-plate into its position using the 2 screws. When mounting on a stone or concrete wall drill 5mm holes for the plugs. When mounting on wood, drill with 2.5mm. © Nedap AVI Page 6 of 19 uPASS Access Install the uPASS Access reader onto the base-plate. 1. Feed the cable through the cable entry hole. Important note: minimum bending radius 30mm. 2. Attach the top of the uPASS Access onto the base-plate. 3. Fix the assembly using the screw on the bottom. Figure 2: uPASS Access installation © Nedap AVI Page 7 of 19 uPASS Access 3 CONNECTIONS The uPASS Access is supplied with a 5 meter (15 feet) shielded cable pigtail with 12 multi-color wires. RED BLACK BROWN GREEN GRAY PINK YELLOW GRY/PNK RED/BLU WHITE PURPLE BLUE SHIELD Note: © Nedap AVI Power supply 12 - 24VDC. Power supply 0VDC, DC-Ground. RS485 ARS485 A+ Data-0 / Clock Data-1 / Data Tamper switch (normally closed) Tamper switch (common) Led_UL_IN* Led_NA_IN* Nedap antenna interface. RFMOD antenna modulation. Connect to ANT. Beeper_IN* Shield Cable shield shall be connected to the metal case of the external device(s). Cable extensions shall only be made by means of shielded cable(s). All shields of the shielded cable extensions shall be connected together and to the metal case of the external device(s). Led_UL_IN*, Led_NA_IN* and Beeper_IN* are inputs that are active LOW. Page 8 of 19 uPASS Access 3.1 POWER SUPPLY The uPASS Access requires DC power supply in the range from 12 – 24V. Maximum current consumption is 1A @ 12VDC, 0.5A @ 24VDC. Connections: RED BLACK SHIELD Note: 3.2 3.2.1 Power supply 12 - 24VDC. Power supply 0V / DC-ground. Shield connected to DC-ground . Extending this connection beyond the 5 meter pig tail length shall ONLY be allowed using shielded cable. The minimum voltage at the end of the fixed shieled pigtail cable shall be greather then 12VDC -10% The shield shall be connected to the metal case of the external device. COMMUNICATION RS485 The uPASS Access reader has a RS485 interface for communication with a host system or for configuring reader settings. The RS485 interface is a 2-wire half-duplex serial communication interface using balanced lines. Connections: BROWN GREEN SHIELD Note: 3.2.2 RS485 A- Balanced RX/TX RS485 A+ Balanced RX/TR Shield connected to DC-ground. The RS485 interface is disabled while the USB interface is in use! Extending this connection beyond the 5 meter pig tail length shall ONLY be allowed using shielded twisted pair cable(2 x 2 x 0.25 mm2) as long as the total length is shorter then 1200 meters, 6000 feet, cable capacity < 100 pF/meter. The second twisted pair shall be used for the DC power supply. The shield shall be connected to the metal case of the external device. USB The uPASS Access reader features an USB interface for service, installation and firmware upgrade purposes. The Mini-USB connector is located on the bottom of the device and can only be reached when the bottom screw is opened and the uPASS Access is lifted away from the base-plate. This ensures that unauthorized modifications to the reader settings can be detected using the tamper switch. The USB interface can be used to configure the reader using the UHFTOOL software. Note: While the shielded USB cable is connected, the RS485 interface is disabled! The maximum shielded cable length shall be < 2 meter. USB Driver installation Make sure your computer is connected to the internet. The driver should install automatically via Windows update when the uPASS Access reader is connected to your PC via the USB cable. Follow the driver installation wizard. If you do not see the Windows update pop-up, you can manually install the driver. To manually install, you need to go to FTDI’s website at www.ftdichip.com/Drivers/VCP.htm and download the VCP (Virtual Com Port) drivers for your operating system. Drivers for MacOS and Linux are available as well. © Nedap AVI Page 9 of 19 uPASS Access 3.2.3 WIEGAND / MAGSTRIPE The wiegand interface connections also support magstripe. NEDAP UHF Wiegand tags will generate a wiegand message on the interface. NEDAP UHF Magstripe tags will generate a magstripe message on the interface. Other UHF tags will not generate a message on this interface, unless the 'Extra output' settings are used! The wiegand/magstripe output format is determined by the programmed format of the tag. Make sure to order the correct tag formatting if you want to use the wiegand or magstripe interface. See also the UHF tags order guide for more information. Connections: GRAY PINK BLACK SHIELD Wiegand connections Magstripe connections Data-0 Clock Data-1 Data Ground Ground Shield connected to DC-ground. Note: Extending these connections beyond the 5 meter pig tail length shall ONLY be allowed using shielded cable (4 x 0.25 mm2) as long as the total length is shorter then 150 meters (500 feet). The shield shall be connected to the metal case of the external device. 3.2.3.1 WIEGAND TIMING In the figure below the Wiegand protocol timing is specified. Tpw DATA-1 5V 0V DATA-0 5V 0V Tpw Tpi Tpi Figure 3: Wiegand protocol timing 3.2.3.2 Timing constants: Tpi Pulse interval time Tpw Pulse width time 1msec 50µsec MAGSTRIPE TIMING The magstripe message length is determined by the tag. The first character will be a start-sentinel (0xB). The message is terminated with an end-sentinel character (0xF) and an LRC character. The figure below shows the timing for one magstripe character. Each bit consists out of one period low (220µsec) and two periods high (440µsec). The Data-signal is valid and stable on the falling edge of the Clocksignal. Before and after the data 16 clock pulses are generated (postamble and preamble). 3300µsec 660µsec CLK 5V 0V DAT 5V 0V 220µsec lsb msb odd parity Timing constants: Clock period Clock high Clock low Data pre-amble Data post-amble Figure 4: Magstripe protocol timing one character © Nedap AVI 660µsec 440µsec 220µsec 16 clock periods 16 clock periods Page 10 of 19 uPASS Access 3.3 LED CONTROL The built-in high intensity LED provides visual feedback that the tag has been read or authorized. The LED and buzzer can be controlled by the access control system. Automatic mode: Default the uPASS Access will automatically control the LED. During stand-by the LED will be RED and upon identification it will be GREEN. These colors can be changed! Remote control: The LED can be controlled remotely by a connected access control system. Digital inputs will determine the color indicated on the LED. Use UHFTOOL to enable the Remote LED control mode. RED/BLU WHITE BLUE BLACK SHIELD Note: 3.4 Led_UL_IN* Led_NA_IN* Beeper_IN* Ground Shield connected to DC-ground. Extending these connections beyond the 5 meter pig tail length shall ONLY be allowed using shielded cable (4 x 0.25 mm2) as long as the total length is shorter then 150 meters (500 feet). The shield shall be connected to the metal case of the external device. TAMPER SWITCH An internal magnet provides tamper indication when the reader is dismounted. This contact may be connected to an external alarm system. The contacts are normally closed when the reader is in place. Tamper switches of multiple readers can be connected in series. Connections: YELLOW GRY/PNK SHIELD Tamper switch (normally closed) Tamper switch (common) Shield connected to DC-ground. Contact ratings: Max. current Max. switching voltage Note: 3.5 50 mA (0.5 Volt voltage drop) +24 VDC Extending this connection beyond the 5 meter pig tail length shall ONLY be allowed using shielded cable (2 x 0.25 mm2) as long as the total length is shorter then 150 meters (500 feet). The shield shall be connected to the metal case of the external device. NEDAP ANTENNA INTERFACE The Nedap antenna interface is used to connect the uPASS Access to NEDAP AEOS access control hardware such as the AP1001. Instead of proximity antenna the uPASS Access can be connected. Connections: PURPLE BLACK SHIELD Note: © Nedap AVI Nedap antenna interface. RFMOD antenna modulation. Connect to ANT. Nedap antenna interface. Ground, shield. Connect to ANT GND. Shield connected to DC-ground. Extending this connection beyond the 5 meter pig tail length shall ONLY be allowed using coaxial cable, RG58U, as long as the total length is shorter then 100 meters (350 feet). The shield shall be connected to the metal case of the external device. Page 11 of 19 uPASS Access 4 UHF FREQUENCIES 4.1 RADIO REGULATIONS The uPASS Access reader operates on the 860 – 960 MHz band. Regulations in this band are not standardized world-wide. Generally the regulations can be divided into several regions. Per region a specific frequency band is available. This frequency band is divided into frequency channels. If local radio regulations require frequency hopping (FHSS), then the uPASS Access automatically selects and uses the available channels. Region Europe Americas Brazil China Australia Israel Korea New Zealand Japan Malaysia Taiwan Vietnam Technique FHSS FHSS FHSS FHSS FHSS FHSS FHSS Frequency Channels 865.6 - 867.6 MHz 902.7 - 927.2 MHz 915.5 - 927.5 MHz 920.5 - 924.5 MHz 920.7 - 925.2 MHz 915.0 - 917.0 MHz 917.7 - 920.1 MHz 917.7 - 920.1 MHz 917.3 - 920.3 MHz 919.8 - 922.2 MHz 922.6 - 927.4 MHz 920.7 - 924.3 MHz 52 43 20 12 Table 1: Region specific parameters 4.2 FREQUENCY CHANNEL SELECTION If no frequency hopping is required, you should select an available frequency channel manually. This can be realized as described below. Select an available frequency channel to achieve the best performance and to avoid interference from other readers or equipment. Use UHFTOOL to setup the frequency channel selection. © Nedap AVI Page 12 of 19 uPASS Access 5 READER CONFIGURATION The uPASS reader settings can be configured easily using the UHFTOOL software. Software developers can find the communication protocol description in the firmware manual. 5.1 UHFTOOL SOFTWARE Figure 5: UHFTOOL software 5.2 SETTINGS Click 'View', 'Show config sidebar' or press F11 to show the configuration sidebar. In the sidebar the configuration categories are shown. Expand or collapse the setting panels by clicking on it. 5.2.1 READ DATA Configure here which tags should be selected, how to access these tags, what data should be read from these tags and if a security check should be performed. By default the reader is configured to select ANY TAG and read its EPC number. Select NEDAP to read only Nedap tags. NEDAP DUAL-ID (introduced in firmware version 2.29) enables the uPASS to search for Nedap vehicle-id tags. When a vehicle-id tag is found, the uPASS searches for driver-id tags. Example 1: Read only NEDAP UHF tags and use two way authentication: Figure 6: Read data example 1 © Nedap AVI Page 13 of 19 uPASS Access Example 2: Read only NXP UCODE tags (TID starts with E2006) and read 4 words from user memory. Figure 7: Read data example 2 5.2.2 DECODE NEDAP XS Enable decode Nedap XS formatted tags. Introduced in firmware version 2.54. Figure 8: Output settings By default the data on NEDAP XS formatted tags will be transmitted to the TRANSIT compatible processor or the the NEDAP antenna modulation interface. In this case the UPASS will not perform any decoding. Enable decode Nedap XS when you do not want to use the TRANSIT compatible processor or the antenna modulation interface. The UPASS will decode the NEDAP XS tag data and output its plain tag-number. You can also enable to output or verify the customer code. The decoded NEDAP XS output number contains: Byte 1: 4E NEDAP UHF Byte 2:FMT=01: Nedap XS decoded hex tagno FMT=02: Nedap XS decoded decimal tagno. Byte 3-4: 00 Unused Byte 5-7: CC CC=Customer code (zero if not transmitted) Byte 8-12: TAGNO TAGNO=Tag number Examples: NEDAP UHF XS: NEDAP UHF XS decoded: NEDAP UHF XS decoded decimal: NEDAP UHF XS decoded + custcode: NEDAP UHF XS decoded decimal + custcode: © Nedap AVI Output: 4E10 Output: 4E01 Output: 4E02 Output: 4E01 Output: 4E02 3FFF 0000 0000 0000 0000 C415 0000 0000 0415 0415 A87C 0000 0000 A000 A000 BD51 0000 0001 0000 0001 8000 3039 2345 3039 2345 Page 14 of 19 uPASS Access 5.2.3 RELAY / TIMING Configure relay output and timing parameters. Figure 9: Relay / timing settings Enable 'Automatic relay activation' to activate the relay upon identification. When disabled the relay can only be activated manually. The 'Relay hold time' setting is the minimum time the relay is activated. The 'Vehicle hold time' setting is the time, after a vehicle-id tags has been found, for which the reader will search for driver-id tags. This setting is only used in the NEDAP DUAL-ID mode. Introduced in firmware version 2.29. The (random) RF off time parameter can be used to enable time sharing between multiple readers on the same frequency. 5.2.4 LED CONTROL Only for UPASS ACCESS: setup LED control mode. Automatic mode: Default the uPASS Access will automatically control the LED. During stand-by the LED will be BLUE and upon identification it will be GREEN. These colors can be changed! Figure 10: LED control Remote control: The LED can be controlled remotely by a connected access control system. Digital inputs will determine the color indicated on the LED. © Nedap AVI Page 15 of 19 uPASS Access 5.3 EXPERT SETTINGS Click 'Options', 'Usermode', 'Expert' to show additional configuration settings for advanced users. 5.3.1 OUTPUT Configure communication output settings. Figure 11: Output settings Select 'Enable serial id-events' to enable the serial output upon identification. Only disable the serial id-events to optimize the identification speed when using the wiegand or magstripe interface or the TRANSIT compatible processor. When 'Fast repeat serial id-events' is selected (default) the serial output is repeated upon every identification. When this option is disabled, the message is only sent once. Enable 'Repeat using hold-time interval' to repeat id-events with hold-time interval. The repeating will be enabled for the serial and also for the wiegand or magstripe interface. 'Enable vehicle id-events' allows enabling or disabling the id-event messages for vehicle-ids. This may be useful in combination with the NEDAP DUAL-ID mode and an access control panel that does not support the dual-id feature. 5.3.2 OUTPUT MESSAGE FORMAT Configure output message format. Figure 12: Output message format The output message format is configurable: [ ] [ ] [ ] [ ] [] [ CR/LF ] Note: © Nedap AVI When the output message format is changed, identified tags may no longer be shown in the UHFTOOL. Page 16 of 19 uPASS Access 5.3.3 EXTRA OUTPUT Optionally enable wiegand or magstripe output for tags that are not programmed by Nedap in a wiegand, magstripe or nedap-xs format. This feature is introduced in firmware version 2.13 or newer. 'Protocol': Disabled Wiegand Magstripe Do not use the additional output feature. Enable additional wiegand output. Enable additional magstripe output. 'Data source': EPC number Output the EPC number using the selected protocol. Custom read data Output the custom data read using the selected protocol. See for more information about how to setup custom read data chapter 5.2.1. 'Alignment': Full Left Right Use the complete EPC number (or all custom read data). Truncate data. Keep left. Truncate data. Keep right. 'Data length': Data length in bits for wiegand (or in digits for magstripe). 'Offset': Data offset in bits for wiegand (or in digits for magstripe). 'Add constant': Enable to add a constant to the output before or after the data read from the tag. Example 1: Output a wiegand 26-bit message with facility code 10: Example 2: Output the 13 rightmost digits from the EPC number using the magstripe interface: Figure 14: Additional output example 2 Figure 13: Additional output example 1 © Nedap AVI Page 17 of 19 uPASS Access 5.3.4 FREQUENCY Here is shown the reader's operating frequency region. Only for systems that do not use frequency hopping (e.g. in Europe): You can select a frequency channel within the available frequency band. Figure 15: Frequency 5.3.5 READ RANGE Enable the squelch to reduce the read range. This is useful to optimize lane separation. When the squelch is enabled, you can set the squelch level. This level ensures that only tags with a returned signal strength higher then the squelch level are identified. When the squelch is enabled and the returned signal strength is lower then the squelch level, the SQ-ACT LED indicates that the tag is rejected. Figure 16: Read range © Nedap AVI Page 18 of 19 uPASS Access TECHNICAL SPECIFICATIONS ITEM SPECIFICATION Dimensions 150x50x40mm Weight 0.5 kg Enclosure Polycarbonate (RAL7016) Chassis material Aluminum (Zamak5) (RAL9006) Protection class IP65 Operational temperature -30 °C … + 60 °C Relative humidity 10 .. 93 % non condensing Identification range Up to 2 meters (Line Off Site) Power supply 12 … 24VDC ±10% linear power supply Current consumption 1A @ 12VDC, 0.5A @ 24VDC Inputs 2 digital input for LED control 1 digital input for buzzer control Active low inputs Tamper indication Yes by tamper switch Dry contact Output Wiegand, magstripe (clock & data) Cable Fixed shielded cable length of 5 meter (16 feet) included Cable extensions beyond the 5 meter shall ONLY be allowed using shielded cable Interfaces RS485 and USB USB local service only Air interface ISO18000-6C Operating frequency Europe: Americas: Brazil: China: Australia: REMARK (5.9 x 1.9 x 1.5 inch) (1.1 lbs) (Approx. NEMA4x) (-22°F … +140°F) With passive NEDAP UHF tags 865 … 868 MHz 902 … 928 MHz (FHSS) 915 … 928 MHz (FHSS) 920 … 928 MHz (FHSS) 920 … 926 MHz (FHSS) Polarization Horizontal + Vertical ERP / EIRP < 1 W (30 dBm) ERP (CE) < 4 W (36 dBm) EIRP (FCC) Safety EN 60950 Emission EN 302 208-1,-2 v1.3.1 FCC part 15.247 incl. Spread Spectrum Industry Canada RSS210 (6 feet) Switched every query round PART NUMBERS READERS NEDAP uPASS Access (EUR) NEDAP uPASS Access (USA) © Nedap AVI part number: part number: 9958240 9206663 Page 19 of 19
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Hans Rappard Create Date : 2013:03:18 15:15:08+01:00 Modify Date : 2013:03:18 15:15:57+01:00 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2013:03:18 15:15:57+01:00 Creator Tool : Acrobat PDFMaker 9.1 for Word Document ID : uuid:75acdc1d-82d8-4527-bdb5-d53aebf2a4d2 Instance ID : uuid:56024b02-03cf-45f0-8e7e-43ae57721c38 Subject : 30 Format : application/pdf Title : uPASS Access Creator : Hans Rappard Producer : Adobe PDF Library 9.0 Source Modified : D:20130318141449 Company : NEDAP N.V. Page Layout : OneColumn Page Count : 19EXIF Metadata provided by EXIF.tools