Nedap N V X2 Anti-Pilferage Device User Manual 02

N. V. Nederlandsche Apparatenfabriek NEDAP Anti-Pilferage Device 02

UserManual.wiki >

X2 User Manual >

Contents

User Manual 02

- 1 -manualX2 ElectronicsFebruari 2012

- 3 -Table of Contents2 Technical Support2 Safety precautions2 Copyright Notice4 1. Introduction4 1.1 Communication functions4 1.2 Customer Counting4 1.3 Key Switch4 1.4 Crying Funtion5 1.5 Benets5 1.6 Software version6 2. Block diagram SDR PCB6 2.1 Network communication control6 2.1.1 Hand-terminal-connection6 2.1.2 Data communication over coax and Power6 2.2 Anti-deactivation regulation (Detection mode)6 2.3 Tag Analyzer6 2.4 Transceiver section7 2.5 Master - Slave settings and status LEDs7 2.5.1 View X2 electronics Status7 2.5.2 Change X2 functionality7 2.6 X2 approved antennas7 2.7 Data communication8 2.8 Customer counting8 2.9 DC Power Supply9 3. PCB Components overview9 3.1 Connector overview9 3.2 LED overview10 4. Unit address10 5. Connection to PC / Laptop11 6.CongurationManager11 6.1 PL TAB11 6.2 PL RX TAB11 6.3 PL TX TAB12 6.4 PL Sync TAB13 6.5 PL Alarm TAB13 6.6 ASC13 6.7 Spectrum analyzer15 7.Systemconguration15 7.1 Medium scale installation example17 8.SpecicationsX2

- 4 -1. Introduction• System adapt to any environment • Cognitive (Radio) system (Software Dened Radio)• It monitors the utilization of the RF spectrum in the neighborhood, and congures it self for best performance• Quickly and easily upgradeable with enhanced features• Can be recongured “on-the-y”: Detection or label analyzerSoftware radio is the art and science of building radios using software. By radio, we mean any kind of device that intentionally transmits or receives signals in the radio frequency (RF) part of the electromagnetic spectrum. Given the constraints of today’s technology, there is still some RF hardware involved, but the idea is to get the software as close to the antenna as is feasible. Ultimately, we’re turning hardware solutions into software solutions.The label analyzer has an increased detection range, and has a quick detection and deactivation including important information like accurate Q and frequency measurement. It can also measure differences in deactivation levels.The detection system can function without NCC and can be switched into a master.1.1 Communication functionsCommunication remote assistance or data delivery is done by use of an NCC MK2 master unit. There are no onboard communication functions. With a combination of customer counting and above capabilities you can use, alter and monitor remote-diagnostics, rmware-upgrade and system congurations.To communicate with the Nedap Conguration Manager, a connection through USB has to be established. This is a connection between the onboard Mini-USB connector K210 and an USB connector in the PC or laptop.1.2 Customer CountingThe X2 PCB has Customer Counting possibilities for one aisle. Gathered data can be shown on the Easinet™. 1.3 Key SwitchThe X2 can be tted with an Key Switch. The switch has to be connected to K208 (for connector images, see 1.2 Customer Counting).1.4 Crying FuntionX2 electronics are standard tted with a buzzer for the crying function. The buzzer will be connected to connector K206.The buzzer is tted to a mounting plate. External USB(mini) cong portK210

- 5 -1.5 Benets• 1 aisle CC option (K208)• 1 opto input for key switch (K208)• Standard delivered with a buzzer for use of the crying function option (K206)• Conguration Manager connection by USB1.6 Software versionThe latest version of the Conguration Manager must be installed for use with the new electronics The sweep time has changed, there fore all units in a system must have rmware version 2.xxx or higher!X2Unit X2 Cable 2 FR + MDAC-AYYYY-MM-DDDocumentation released-Ref.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6325678A38017328N/AA.01 ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:478543210.01 OF 11:2± 1°± 0.2DESCRIPTIONLIN.ANG.N/A?????? DRW: CHCK:YYYY-MM-DDYYYY-MM-DDYYYY-MM-DD DSGN:AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A48017336N/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??Buzzer with cableAYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEFFEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??2x M3x10 2x M4x10AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??2x M3x6Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:01Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong port Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included) DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA567A3QUICK REFERENCE X25276659 ARTICLE NUMBERISO AGROENLO HOLLAND SHEET:475432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK: DSGN:A-AYYYY-MM-DDRef.Nr.REV.ROUGHNESS ACC.32145Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong port Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inDeact. buzzerCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK208 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA567A3QUICK REFERENCE X25276659 ARTICLE NUMBERISO AGROENLO HOLLAND SHEET:47543211:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/A DRW: CHCK: DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong port Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA567A3QUICK REFERENCE X25276659 ARTICLE NUMBERISO AGROENLO HOLLAND SHEET:47543211:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK: DSGN:Pin 1 = GndPin 2 = +33Volt inK1 (YELLOW)(Not included)Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209(BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF65678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785445.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:

- 6 -2. Block diagram SDR PCBThe X2 PCB combines the communication control unit, the transmitter and receiver in one single unit. 2.1 Network communication controlFor network communication an external NCC (NCC MK2, SQ) is necessary.2.1.1 Hand-terminal-connectionThe use of a handheld terminal is not available for the X2 unit.2.1.2 data communication over coax and PowerOne of the important features of the X2 electronics is the data-com over the coax cable. With this feature it’s not necessary to use an extra data-cable between the units, which simplies the installation of the system. An NCC MK2 unit plays a central roll in providing the data-com. All the connected units are interrogated periodically by this unit. If there are messages like an alarm on a connected X2 unit, then the NCC MK2 unit will process this and takes the necessary action: Sending a command to turn on the lamps on the activated aisle.The X2 has two slave-sync connectors (K101 and K102) from which the unit can be driven from a NCC MK2, SQ, DQ or another networking unit. X2 electronics can also act as a stand-alone unit, without the need for any synchronization. DC power supply always from its own Master DC input connector K3 or from the power inserter.2.2 Anti-deactivation regulation (Detection mode)To prevent unwanted deactivation during detection of a label, the transmitted power will be reduced when a label is in its proximity. It is a high speed loop. The user will not notice a difference in response.2.3 Tag AnalyzerIn tag analyzer mode, the power is constant. The tag analyzer has the ability to detect, store label information, like accurate Q and frequency measurement. It can also measure differences in deactivation levels.By using a piezo a label can be detected, the signal strength will be visualized by a repeating audio signal. When a label is no longer detected, the gathered information will be stored. When a low Q label is detected, the transmitter signal will be increased; the label will be quicker deactivated.2.4 Transceiver sectionThe X2 makes use of the pulse (transmitter) and listen (receiver) technique. This is the same technique used with radar. This gives the freedom to use it with mono-antennas.The X2 uses a transceiver architecture that gives the highest exibility possible today. The analog signal from the antenna is almost directly converted to digital domain. The transmitter signal is just before the antenna converted to analog.The analog to digital converter (ADC) has a high dynamic range and runs on a high frequency. This gives the possibility to handle strong interference without clipping/distorting the wanted label signal in the receiver.The antenna is connected to K1.When a single unit X2 is stand-alone no synchronization is necessary. In all other situations the transceiver needs to be synchronized for best performance. X2Unit X2 Cable 2 FR + MDAC-AYYYY-MM-DDDocumentation released-Ref.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6325678A38017328N/AA.01 ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:478543210.01 OF 11:2± 1°± 0.2DESCRIPTIONLIN.ANG.N/A?????? DRW: CHCK:YYYY-MM-DDYYYY-MM-DDYYYY-MM-DD DSGN:AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A48017336N/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??Buzzer with cableAYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEFFEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??2x M3x10 2x M4x10AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??2x M3x6Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:01Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong port Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included) DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA567A3QUICK REFERENCE X25276659 ARTICLE NUMBERISO AGROENLO HOLLAND SHEET:475432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK: DSGN:A-AYYYY-MM-DDRef.Nr.REV.ROUGHNESS ACC.32145Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong port Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inDeact. buzzerCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK208 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA567A3QUICK REFERENCE X25276659 ARTICLE NUMBERISO AGROENLO HOLLAND SHEET:47543211:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/A DRW: CHCK: DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong port Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA567A3QUICK REFERENCE X25276659 ARTICLE NUMBERISO AGROENLO HOLLAND SHEET:47543211:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK: DSGN:Pin 1 = GndPin 2 = +33Volt inK1 (YELLOW)(Not included)Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209(BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF65678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785445.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:

- 7 -The receiver receives its RF reference signal and conguration data from the local communication control section. Transmitter:Although the effective RF power is in the same range as our high power swept system, the peak signals are much higher. As a consequence of that, the label can be deactivated at larger distances from the antenna compared to the swept system. For that reason the X2 has an RF power-control. This control will reduce it’s transmit power when it detects a label within the deactivation range. Interferences like a swept system will be suppressed from inuencing the power-control. In the label analyzer mode the TX power will not decrease, but increase when a low Q-factor label is brought into the detection eld.Receiver:The selectivity and dynamic range is very high. The selectivity is achieved with advanced high-speed digital lter techniques. This gives the advantages to be able to work in environments with large level interferences.2.5Master-SlavesettingsandstatusLEDsChanging the unit functionality between slave and master can be done by pushing button SW3. (See page 20)2.5.1 view x2 electronics statusPress button SW3 1x (See page 20).• When the yellow LED starts to blink and the red LED burns continiously, the X2 is set as a slave.• When both LED’s are blinking, the X2 is set as master.2.5.2 cHange x2 functionalityPress button SW3 (See page 20) 2x within 5 seconds to switch to master (or slave) status. The X2 electronics is standard programmed as slave.2.6 X2 approved antennasNedap has a broad range of antennas. Not all antennas are approved in combination with the X2 electronics. In the near future more and more antennas will be X2 ready. It is important to know that only HIGH POWER antenna’s can be used for safety reasons. At the time of writing this document the following Nedap antennas are approved for use with X2 electronics:• FL30• FL45• D40• D50• PG27• PG39• EQ45-FK1Antenna (Tx-out)Master/slave switchSW3Datacom error(Red)Alarm(Yellow)

- 8 -2.7 Data communicationThe X2 uses the same communication and synchronization signals as the sweep system of Nedap Retail. The transceiver is a slave. Slaves are polled by the master. The communication control section, which is the master unit, polls periodically all connected slaves and relays data to other devices e.q. other control units or PC’s.With every sweep one slave is polled. The polled slave must answer, this happens in the same sweep. These poll and answer data packets are used implement the network functionality. 2.8 Customer countingThe X2 PCB is prepared with customer counting on board. 2 Sensors can be connected to monitor 1 entrance with direction sensitivity.The passage between sensors is shaped and buffered and processed by the processor. In this way incoming and outgoing label alarms can be counted for separately.The customer counting wires can be connected to connector K208.The sensor power output is 12 V dc. It is possible to connect sensor with positive or negative going output signals.Two customer counting status LED’s are situated on the PCB to indicate if the sensors are fully functional.2.9 DC Power SupplyPower over synchronization is possible for X2. DC supply always from its own Master DC input connector K3 or from a power inserter . Pin 1 = GndPin 2 = +33Volt inK3X2Unit X2 Cable 2 FR + MDAC-AYYYY-MM-DDDocumentation released-Ref.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6325678A38017328N/AA.01 ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:478543210.01 OF 11:2± 1°± 0.2DESCRIPTIONLIN.ANG.N/A?????? DRW: CHCK:YYYY-MM-DDYYYY-MM-DDYYYY-MM-DD DSGN:AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A48017336N/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??Buzzer with cableAYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEFFEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??2x M3x10 2x M4x10AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??2x M3x6Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:01Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong port Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included) DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA567A3QUICK REFERENCE X25276659 ARTICLE NUMBERISO AGROENLO HOLLAND SHEET:475432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK: DSGN:A-AYYYY-MM-DDRef.Nr.REV.ROUGHNESS ACC.32145Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong port Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inDeact. buzzerCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK208 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA567A3QUICK REFERENCE X25276659 ARTICLE NUMBERISO AGROENLO HOLLAND SHEET:47543211:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/A DRW: CHCK: DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong port Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA567A3QUICK REFERENCE X25276659 ARTICLE NUMBERISO AGROENLO HOLLAND SHEET:47543211:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK: DSGN:Pin 1 = GndPin 2 = +33Volt inK1 (YELLOW)(Not included)Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209(BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF65678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785445.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:CC 1(Yellow)CC 2(Yellow)X2Unit X2 Cable 2 FR + MDAC-AYYYY-MM-DDDocumentation released-Ref.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6325678A38017328N/AA.01 ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:478543210.01 OF 11:2± 1°± 0.2DESCRIPTIONLIN.ANG.N/A?????? DRW: CHCK:YYYY-MM-DDYYYY-MM-DDYYYY-MM-DD DSGN:AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A48017336N/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??Buzzer with cableAYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEFFEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??2x M3x10 2x M4x10AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??2x M3x6Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:01Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong port Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included) DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA567A3QUICK REFERENCE X25276659 ARTICLE NUMBERISO AGROENLO HOLLAND SHEET:475432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK: DSGN:A-AYYYY-MM-DDRef.Nr.REV.ROUGHNESS ACC.32145Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong port Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inDeact. buzzerCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK208 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA567A3QUICK REFERENCE X25276659 ARTICLE NUMBERISO AGROENLO HOLLAND SHEET:47543211:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/A DRW: CHCK: DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong port Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA567A3QUICK REFERENCE X25276659 ARTICLE NUMBERISO AGROENLO HOLLAND SHEET:47543211:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK: DSGN:Pin 1 = GndPin 2 = +33Volt inK1 (YELLOW)(Not included)Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209(BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF65678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785445.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:

- 9 -X2Unit X2 Cable 2 FR + MDAC-AYYYY-MM-DDDocumentation released-Ref.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6325678A38017328N/AA.01 ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:478543210.01 OF 11:2± 1°± 0.2DESCRIPTIONLIN.ANG.N/A?????? DRW: CHCK:YYYY-MM-DDYYYY-MM-DDYYYY-MM-DD DSGN:AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A48017336N/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??Buzzer with cableAYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEFFEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??2x M3x10 2x M4x10AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??2x M3x6Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:01Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong port Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included) DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA567A3QUICK REFERENCE X25276659 ARTICLE NUMBERISO AGROENLO HOLLAND SHEET:475432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK: DSGN:A-AYYYY-MM-DDRef.Nr.REV.ROUGHNESS ACC.32145Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong port Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inDeact. buzzerCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK208 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA567A3QUICK REFERENCE X25276659 ARTICLE NUMBERISO AGROENLO HOLLAND SHEET:47543211:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/A DRW: CHCK: DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) cong port Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.6321FEDCBA567A3QUICK REFERENCE X25276659 ARTICLE NUMBERISO AGROENLO HOLLAND SHEET:47543211:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK: DSGN:Pin 1 = GndPin 2 = +33Volt inK1 (YELLOW)(Not included)Master/slave switchAntenna(TX-out)USB (mini) cong portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209(BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF65678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785445.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:3. PCB Components overview3.1 Connector overview3.2 LED overviewPower on(Green)CC 1(Yellow)CC 2(Yellow)Datacom error(Red)Alarm(Yellow) 50 Ω (1) ON OFFNo function(2)

- 10 -4. Unit addressThe X2 PCB has one network address. Be sure the correct Functionality Modules are installed5. Connection to PC / LaptopThe X2 uses a min-usb connector for a direct connection with the Conguration Manager.

- 11 -6.CongurationManagerAll real-time data displayed in the conguration manager, is a subset from the real data. The data communication is not showing all data, to limit the load on the data bus.6.1 PL TABBelow there are 4 real-time parameters, Alarm (red colored), Pulse Count, Sinus / Gauss and internal label detected counter. The alarm is indicating that the two blue markers are simultaneous in the green area, when the label is gone this alarm will immediately dim. The lamp on the antenna will be triggered by this signal but has a hold function. The channel and corresponding frequency will always give a predicted value of the center frequency of the label. When there is no label, it will predict it in the noise. This results in random changes.The counter is an internal counter and independent from the counter used for easi/net. The counter has a reset button ‘clear’. During switching on the unit, the FPGA on board has to be booted. The FPGA status tells if this process succeeded.A View Spectrum button will open another window with a real-time plot of the spectrum.The button Save & Close saves all the control parameters into a ash and closes this window. During next boot, the new written control parameters will be loaded.6.2 PL RX TABThis is the main window that gives a quick overview of the system dynamics. There are two displays showing information of the actual Q and number of valids. In this display is a green colored range. This gives the threshold of the receiver for generating alarm. When both blue markers are simultaneous in the green area an alarm will be generated. The zoom control is centered at the max. value of the Q-factor and the min. value of the Valids.The control SNR is automated in case Automatic Sensitivity Control (ASC) is allways activated. During booting of the unit, the environment of the antenna must be clean from labels.Start control is default set to a safe value (-3.2dB). This must be save for almost all situations. When the installation of all units is done and stable, you can test if the performance is ok. The performance can be tweaked to its highest level by changing the Start control to a lower loss value. The dB scale is indicating the expected sensitivity performance compared to the perfect situation with a label of Q=80. In situations of using labels with very low Q, it is giving the most boost. High Q labels benet not so much from changing this control. 6.3 PL TX TABThe transmitter can be switched on/off with TX On.Temperature is monitored and the TX RF power is reduced or switched off when the temperature is above normal.To prevent label from deactivating, a power control can be used. This control will reduce the RF power at the antenna when a label enters in its possible deactivation level. The Power meter indicates the actual power of the RF power amplier, where 128 is max. power and 0 is min. power.

- 12 -6.4 PL Sync TABWhen the unit is combined with other units, it needs to be synchronized. This can be switched on/off with unit synchroni- zation (sync). With unit sync activated, the timing of all the units will be such that the have no/minimum interference from each other. The sync offset must be set depending on the connection to the NCC. When the unit is connected to the master NCC this offset is 0. When the unit is connected to the rst slave NCC this offset must be set to 1, the second NCC to 2, third NCC to 3 etc. There are two sync slots 0 and 1. It is free to select a value. Between units with a different value one is 0 and the other 1, means they are 100% independent from each other even in an environment with very strong coupling between antennas at large distances. Remark: When unit sync is active and no sync is connected, the buzzer and RF signal are switched off to prevent false alarms in this and other units. When Unit sync is activated but no sync signal is connected, the RED LED on the unit is on (D101). So RED LED D101 on? No RF TX signal and alarm are given.To synchronize the Nedap Retail sweep system with the X2 we need to set the correct active phase. When a Nedap swept system is synchronized with the X2, all mux settings on the sweep system must be set on 4. This gives phases A,B,C and D. When the sweep system is active in phase A and B the X2 must be switched to the other free phases C and D.This product only supports a sweep system(s) connected to/congured as the master NCC. In default setting, all phases are switched to active (value 1). If a swept system is congured to work on phase 1, the chameleon must have that phase inactive so value 0. In general when synchronizing a swept system with the chameleon, the phases must be inverted from each other.Synchronization of Nedap sweep systems other then NCC MK2 (P2) are not supported.

- 13 -6.5 PL Alarm TABAlarm Enable is default active. When no lamp and buzzer signal must be given it must be switched off. Remember that when switched off, EASi/Net™ will NOT register events.Buzzer mode: select between off, whine or continuous Lamps Pulse mode: is the hold time of the lamp after label is not in the detection eld6.6 ASCWith the ASC Range, the sensitivity can be controlled. If there is a situation that less sensitive is wanted, the ASC range can be increased (larger number). To decrease (lower sensitive) the detection range default ASC=100.Long term valids and log term Q give an indication in the stability of the unit in this environment. If both are 0 and stay 0, the unit function stable.6.7 Spectrum analyzerUsing View Spectrum will open an extra window with a spectrum analyser. The same window can be selected with the TAB Spectrum.

- 14 -This is a real-time spectrum analyser. On the horizontal axe is frequency (between 7.4MHz and 8.8MHz), and vertical is level relative given in dB. The Level can be changed up/down. Scaling can be changed to zoom in and out. Average can be switched between quicker response but more noise to slower response but les noise. At selection View are 3 choices of view types:• All : show everything • Gauss: only update plot when normal noise is detected• Valid: only update plot when normal noise is detected and the correct signal to noise (SNR)These 3 types give you the tools to determine what the spectral environment looks like. Is the environment clean, is there a carrier, is there a swept system or is there a pulse-listen system.

- 15 -7.SystemcongurationThe new X2 electronics can be used as an internal in an antenna or external electronics. By use of an power inserter, 6 electronics can be connected.An NCC MK2 can communicate with up to a maximum of 24 X2 electronics. Table 1Number of antennas Non-connected systems Connected systems1 - 6 1 power inserter 1 NCC7 - 12 1 NCC, 1 Power Inserter same as non-connected, plus modem or LAN13 - 18 1 NCC, 2 Power Inserters same as non-connected, plus modem or LAN19 - 24 1 NCC, 3 Power Inserters same as non-connected, plus modem or LAN25 - 30 2 NCC’s, 3 Power Inserter same as non-connected, plus modem or LAN31 - 36 2 NCC’s, 4 Power Inserters same as non-connected, plus modem or LAN37 - 42 2 NCC’s, 5 Power Inserters same as non-connected, plus modem or LAN43 - 48 3 NCC’s, 5 Power Inserters same as non-connected, plus modem or LAN49 - 54 3 NCC’s, 6 Power Inserters same as non-connected, plus modem or LAN55 - 60 3 NCC’s, 7 Power Inserters same as non-connected, plus modem or LAN61 - 66 4 NCC’s, 7 Power Inserters same as non-connected, plus modem or LANetc. etc. etc.7.1MediumscaleinstallationexampleWhen using a 4 output NCC, a maximum of 24 PCB’s can be connected. Below an example of a system with 19 antennas and 48 antennas.NCC MK2PowerInserterPowerInserterPowerInserter

- 16 -NCC MK2PowerInserterPowerInserterNCC MK2PowerInserterPowerInserterPowerInserter

- 17 -8.SpecicationsX2Frequency : 8.2 MHzAntenna Connections : 1x 50 Ohm BNC Transceiver connectorSynchronization : 1x input 50 Ohm BNC 1x output 50 Ohm BNCWeight : 3 kgTemperature range : 0°C …+40°CPower Supply : 30~33V DC, 400mA

- 18 -GROENLO - HOLLANDCopyright © by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this drawing may be reproduced or distributed in any form or by any means, or stored in a data base or retrieval system without the prior written permission of NEDAP.description:QUICK REFERENCE X2 | art no. 8017328doc. article no: 5276659chk:rev. : Ddrw: CB 2011/03/09sheet: 45.01 of 1drawing: T5276-659X2Unit X2 Cable 2 FR + MDAC-AYYYY-MM-DDDocumentation released-Ref.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A38017328N/AA.01 ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432110.01 OF 11:2± 1°± 0.2DESCRIPTIONLIN.ANG.N/A?????? DRW: CHCK:YYYY-MM-DDYYYY-MM-DDYYYY-MM-DD DSGN:AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A48017336N/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??Buzzer with cableAYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??2x M3x10 2x M4x10AYYYY-MM-DDDocumentation releasedRef.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF4321FEDCBA1234A44092201-rsN/AA ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:N/A± 0.2± 1°1:110.01 OF 1DESCRIPTIONLIN.ANG. DSGN:???? DRW: CHCK:2009-MM-DD2009-MM-DD2009-MM-DD??2x M3x6Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) config portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) config portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) config portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:01Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) config portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:AC-AYYYY-MM-DDDocumentation released-Ref.Nr.REV.DATEDESCRIPTIONAPPROVEDN/A DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A38017328N/AA.01 ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432110.01 OF 11:2± 1°± 0.2DESCRIPTIONLIN.ANG.N/A?????? DRW: CHCK:YYYY-MM-DDYYYY-MM-DDYYYY-MM-DD DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) config portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) config portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:Pin 1 = GndPin 2 = +33Volt in K1 (YELLOW)(Not included)Datacom error (Red)Power on (Green)CC 2 (Yellow)CC 1 (Yellow)Alarm (Yellow)No function (2)50 Ω (1)ONOFF Master/slave switchAntenna(TX-out)USB (mini) config portArt.No: 7706707 NCNCK102Pin 2 = - buzzer (black)Pin 1 = + buzzer (red)Sync inSync outDeact. buzzerKeyswitchCustomer countingK206K3K101K210SW3K209 Keyswitch +3V3R474100Ω GND +3V3IN KSWX2 PCBExternalswitchboxSW12345 10KΩCircuit diagramK208 GND (BLUE)(RED)(GREEN) + 12V for sensorsCC sensor 2CC sensor 1GndK211K208(Not included)T5276-659 DIM. IN MMROUGHNESS ACC.ISO 1302 in µMGENERAL TOLERANCES SCALE: FORMAT: DRAWING: Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of thisdrawing may be reproduced or distributed in any form or by any means, or storedin a data base or retrieval system without the prior written permission of NEDAP.ABCDEF6321FEDCBA5678A3QUICK REFERENCE X25276659c ARTICLE NUMBER REV.ISO AGROENLO HOLLAND SHEET:4785432145.01 OF 21:1± 1°± 0.2DESCRIPTIONLIN.ANG.N/ACBCBCB DRW: CHCK:2009-12-182009-10-262009-10-26 DSGN:

- 19 -

- 20 -parallelweg 2d 7141 dc groenlo the netherlands t +31 (0) 544 47 15 55 f +31 (0) 544 46 58 14e info-rs@nedap.com www.nedapretail.comBACK Manual X2 2012

Navigation menu