Nedap N V X2 Anti-Pilferage Device User Manual 02

N. V. Nederlandsche Apparatenfabriek NEDAP Anti-Pilferage Device 02

Contents

User Manual 02

Download: Nedap N V X2 Anti-Pilferage Device User Manual 02
Mirror Download [FCC.gov]Nedap N V X2 Anti-Pilferage Device User Manual 02
Document ID1638938
Application IDGuNQyPno30jZEarG3LVz7A==
Document DescriptionUser Manual 02
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize207.31kB (2591319 bits)
Date Submitted2012-02-17 00:00:00
Date Available2012-02-17 00:00:00
Creation Date2012-02-13 16:01:45
Producing SoftwareAdobe PDF Library 9.9
Document Lastmod2012-02-13 16:02:07
Document TitleUser Manual 02
Document CreatorAdobe InDesign CS5 (7.0)

X2 Electronics
manual
-1-
Februari 2012
Technical Support
E-Mail : support-rs@nedap.com
Safety precautions
CAUTION - RISK OF ELECTRIC SHOCK - DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED NEDAP SERVICE PERSONNEL.
Lightning flash with an arrowhead, enclosed in a triangle, alerts you to the presence of uninsulated voltage points inside the product which could cause a serious electrical shock.
An exclamation mark enclosed in a triangle alerts you to important operating and maintenance instructions in the documentation provided with the product.
WARNING! To avoid the risk of fire or electrical shock, never expose these products to water or operate in a high humidity
environment.
EN 50419:2005
EN 50419:2005 This European Standard specifies a marking
• of electrical and electronic equipment in accordance with Article 11(2) of Directive 2002/96/EC
(WEEE); This is in addition to the marking requirement in Article 10(3) of this Directive which requires producers to mark electrical and electronic equipment put on the market after 13 August
2005 with a ‘crossed-out wheeled bin’ symbol.
• that applies to electrical and electronic equipment falling under Annex IA of Directive 2002/96/
EC, provided the equipment concerned is not part of another type of equipment that does not fall
within the scope of this Directive. Annex IB of Directive 2002/96/EC contains an indicative list of the
products, which fall under the categories set out in Annex IA of this Directive;
• that serves to clearly identify the producer of the equipment and that the equipment has been put
on the market after 13 August 2005.
© 2009 Nedap Retail Support Netherlands Parallelweg 2d, 7141 DC Groenlo
The software / hardware described in this book / file is furnished under a license agreement and may be used only in accordance with the terms of the agreement.
Documentation version SAFETY Manual X2 2012
Copyright Notice
All Rights Reserved. Any technical documentation that is made available by Nedap Retail Support is the copyrighted work of Nedap Retail Support and is owned by Nedap Retail Support.
No warranty The technical documentation is being delivered to you and Nedap Retail Support makes no warranty as to its accuracy or use. Any use of the technical documentation or the
information contained therein is at the risk of the user. Documentation may include technical or other inaccuracies or typographical errors Nedap Retail Support the right to make changes
without prior notice. No part of this publication may be copied without the express written permission of Nedap Retail Support, Parallelweg 2d, 7141 DC Groenlo, Netherlands
Trademarks Nedap, the Nedap logo, Nedap EASi/Net and the Nedap EASi/Net are registered trademarks of Nedap N.V. Groenlo.
Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.
Digital Printed in the Netherlands
-2-
Table of Contents
Technical Support
12
6.4 PL Sync TAB
Safety precautions
13
6.5 PL Alarm TAB
Copyright Notice
13
6.6 ASC
1. Introduction
13
6.7 Spectrum analyzer
1.1 Communication functions
15
7. System configuration
1.2 Customer Counting
15
7.1 Medium scale installation example
1.3 Key Switch
17
8. Specifications X2
1.4 Crying Funtion
1.5 Benefits
1.6 Software version
2. Block diagram SDR PCB
2.1 Network communication control
2.1.1 Hand-terminal-connection
2.1.2 Data communication over coax and Power
2.2 Anti-deactivation regulation (Detection mode)
2.3 Tag Analyzer
2.4 Transceiver section
2.5 Master - Slave settings and status LEDs
2.5.1 View X2 electronics Status
2.5.2 Change X2 functionality
2.6 X2 approved antennas
2.7 Data communication
2.8 Customer counting
2.9 DC Power Supply
3. PCB Components overview
3.1 Connector overview
3.2 LED overview
10
4. Unit address
10
5. Connection to PC / Laptop
11
6. Configuration Manager
11
6.1 PL TAB
11
6.2 PL RX TAB
11
6.3 PL TX TAB
-3-
1. Introduction
•
•
•
•
•
System adapt to any environment
Cognitive (Radio) system (Software Defined Radio)
It monitors the utilization of the RF spectrum in the neighborhood, and configures it self for best performance
Quickly and easily upgradeable with enhanced features
Can be reconfigured “on-the-fly”: Detection or label analyzer
Software radio is the art and science of building radios using software. By radio, we
mean any kind of device that intentionally transmits or receives signals in the radio
frequency (RF) part of the electromagnetic spectrum.
Given the constraints of today’s technology, there is still some RF hardware
involved, but the idea is to get the software as close to the antenna as is feasible.
Ultimately, we’re turning hardware solutions into software solutions.
The label analyzer has an increased detection range, and has a quick detection
and deactivation including important information like accurate Q and frequency
measurement. It can also measure differences in deactivation levels.
The detection system can function without NCC and can be switched into a master.
1.1 Communication functions
Communication remote assistance or data delivery is done by use of an NCC MK2 master unit. There are no
onboard communication functions. With a combination of customer counting and above capabilities you can use,
alter and monitor remote-diagnostics, firmware-upgrade and system
configurations.
K210
USB(mini) config port
To communicate with the Nedap Configuration Manager, a connection through
USB has to be established. This is a connection between the onboard Mini-USB
connector K210 and an USB connector in the PC or laptop.
1.2 Customer Counting
The X2 PCB has Customer Counting possibilities for one aisle. Gathered data can be shown on the Easinet™.
1.3 Key Switch
The X2 can be fitted with an Key Switch. The switch has to be connected to K208
(for connector images, see 1.2 Customer Counting).
1.4 Crying Funtion
X2 electronics are standard fitted with a buzzer for the crying function. The buzzer
will be connected to connector K206.
The buzzer is fitted to a mounting plate.
-4-
External
D
•
•
•
•
ISO 1302 in µM
switchbox
F F
REV.
External
X2 PCB
External
ACC.
switchboxX2 PCB ROUGHNESS
External
switchbox
+3V3
1 N/A
Ref.Nr.
01
1.5 Benefits
3Documentation released
YYYY-MM-DD
DATE
DESCRIPTION
X2 PCB
GENERAL TOLERANCES
ANG.
LIN.
+3V3 +3V3
+3V3
DIM. IN MM
1:1
A4
SCALE:
+3V3 FORMAT:
± 1°
± 0.2 2 3
+3V3 ISO A
B5
REV.
YYYY-MM-DD
DATE
2009-MM-DD
DRW:
?? 2009-MM-DD
GENERAL TOLERANCES
ROUGHNESS ACC.
ANG.
LIN.
Art.No:
7706707
ISO 1302
in µM
?? 42009-MM-DD
(NotN/A
included)
ROUGHNESS
± 1°
± 0.2
ISO A 4ACC. 5
CHCK:
REV.
DESCRIPTION
N/A
SHEET:
ISO 1302 in µM
Keyswitch
Keyswitch
Circuit
diagramKeyswitch
OFF
External
2D
Alarm (Yellow)
SW
CC 2 (Yellow)
10.01 OF 1
SHEET:
DRAWING:
N/A
K211
Keyswitch
Art.No: 7706707
(Not included)
APPROVED
10.01 OF 1
K206
Pin 2 = - buzzer (black)
Pin 1 = + buzzer (red)
Power
Datacom error
(Red)on (Green)
Datacom error (Red)
K208
K208 Customer
counting
Customer
K208
counting
Customer
counting
K102
K211
K211Keyswitch
Keyswitch
K211
K208
Keyswitch
Customer
NC
counting
NC
Sync out
K101
Sync in
K206
Pin 2 = - buzzer (black)
Pin 1 = + buzzer (red)
K101
Sync in
K209
Deact. buzzer
K102
Sync out
NC
NC
N/A
K211
Keyswitch
(YELLOW)
(BLUE)
(RED)
(GREEN)
K206
Pin 2 = - buzzer
(black)
Art.No: 7706707
included)
Pin 1 = + (Not
buzzer
(red)
K208
Customer
counting
+ 12V for sensors
CC sensor 2
CC sensor 1
K101
Gnd
Sync in
K101
Power on (Green)
in
1(Green)
(Yellow)
PowerCC
onSync
N/A
K3 (Not included)
Pin 1 = Gnd
Pin 2 = +33Volt in
Datacom error (Red)
CC 1 (Yellow)
Circuit diagram
(Not included)
78
N/A
SHEET:
4092201-rs
Datacom error (Red)
Power on (Green)
GND
Alarm (Yellow)
Art.No: 7706707
?? 62009-MM-DD
(Not included)
??SCALE:
2009-MM-DD
1:1 DRW:
in a data base or retrieval system without the prior written permissionPin
of NEDAP.
1 = + buzzerDRAWING:
(red)
K208
Customer
counting
Datacom error (Red)
IN KSW
2009-MM-DD
??DIM. 2009-MM-DD
DSGN: ??
IN MM
SCALE:
DRW:
GROENLO 1:1
HOLLAND
GENERAL
A4 5 CHCK:
FORMAT:TOLERANCES
ANG.
LIN.
No function (2)
R474
GND
100 Ω
Alarm (Yellow)
GENERAL TOLERANCES
LIN.
ANG.
in a data base or retrieval system without the prior written permission of NEDAP.
+3V3
Ω (1)
50+3V3
ON
(2)
OFFNo function10K
Ω
K208
Alarm (Yellow)
Keyswitch
1.6 Software version
(BLUE)
GND 4
YYYY-MM-DD
Documentation released
3 DATE
R474 (RED)
DESCRIPTION
IN KSW
(GREEN)
GND
Ω
100GROENLO
HOLLAND
GND
APPROVED
(NotHOLLAND
DIM.
(YELLOW) DRAWING:
+ 12Vthe
forprior
sensors
in a data base or retrieval system without
written
permission
ofincluded)
NEDAP.
GROENLO
No function
drawing may(2)
be reproduced or distributed in any form or by any means, or stored
X2 PCB
(1)
50 Ωswitchbox
ON
D OFF
Alarm (Yellow)
GND
2009-MM-DD
K3
2009-MM-DD
K3
DSGN: ??
IN MM
(YELLOW)
+ sensors
12V for sensors N/A
(YELLOW)
+ 12V
for
PinB1 = Gnd
PinTOLERANCES
1 = Gnd
CC sensor
3 (BLUE)
2 2 GENERAL
ROUGHNESS ACC.
SCALE: 2 1:1
?? (BLUE)
2009-MM-DD
CC2sensor
DRW: (BLUE)
Pin 2 = +33Volt
in1
CC ANG.
sensor
in
CC sensor
(RED)
LIN.Pin 2 = +33Volt
ISO 1302 in µM NC (RED)
CC1sensor 1
CC(GREEN)
sensor
Gnd
?? NC 2009-MM-DD
± 1° GndFORMAT: A4 CHCK: (RED)
± 0.2
ISO A
NCN/AAPPROVED
IN KSW
(GREEN)
YYYY-MM-DD
Gnd
DSGN: ?? NC
DIM. IN MM
(GREEN)
+ 12V for sensors
REV.
DESCRIPTIONE
NUMBER
(YELLOW)
+ (YELLOW)
12V forARTICLE
sensors
CC sensor 2
(BLUE)
SCALE:
1:2 ADRW: ?? YYYY-MM-DD
CC sensor
K206
(BLUE)
CC
sensor
(RED)
Pin 2 = - buzzer (black)
FORMAT: A3 CHCK: ?? YYYY-MM-DD
CC sensor 1
K206
(RED)
K206
Pin 1 = + buzzer
Gnd (red)
Gnd
SHEET: (black) 10.01
2(GREEN)
= - buzzer
ARTICLECopyright
NUMBER
(GREEN)
OF 1
(c)REV.
by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this Pin
7 or
Pin
2 stored
= -Pin
buzzer
A or distributed in any form or by any means,
drawing
may be reproduced
1 = +(black)
buzzer 8(red)
REV.
Keyswitch
ROUGHNESS ACC.
ISO 1302 in µM
GND
APPROVED
??
drawing may
or distributed in any form or by any means, or stored
N/Abe reproduced
DRAWING:
in a data base or retrieval
system withoutREV.
the prior written permission
of NEDAP.
Ref.Nr.
DATEApparatenfabriek
DESCRIPTION
Copyright (c) by N.V. Nederlandsche
NEDAP. No part of this
drawing may be reproduced
or distributed in any3form or by any means, or stored4
(Not included)
N/A
± 0.2
± 1°
K206
ISO A
DESCRIPTION
Pin 2GND
= - buzzer (black)
GND
50
E Ω (1)2No function (2) Pin 1 = +3 buzzer (red)
50 Ω (1) Circuit diagram
Circuit diagram
ON
No function (2)
ON
OFF
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
R474 SW
Ref.Nr.
GND
Gnd 100 Ω
50 Ω (1)
ON
OFF
GND
CC sensor
Circuit diagram
Circuit diagram
CC sensor 2
GND
SW
ARTICLE NUMBER
A4 CHCK: ?? 2009-MM-DD
FORMAT: REV.
K3
N/A
K3
± 0.2(Not included)± 1°
ISO A(Not included)
K3 (Not included)
AB
AARTICLE ANUMBER
REV.
Pin 1 = Gnd
PinDESCRIPTION
1 =4092201-rs
Gnd
Pin 1 = GndN/A
10.01 OF 1
Pin 2 = +33Volt
in NEDAP.
SHEET:
Pin
2 = in
+33Volt
in 10.01 OF 1 N/A
Pin
2 part
= +33Volt
Copyright (c) by N.V.ANederlandsche
Apparatenfabriek
No
of this
4092201-rs
YYYY-MM-DD
Documentation released
1 aisle CC option (K208)
1 opto input for key switch (K208)
Standard delivered with a buzzer for use of the crying function option (K206)
Configuration Manager connection by USB
8017328
A.01
N/A
SW
Documentation released
DSGN:
DIM. IN MM
DESCRIPTION
YYYY-MM-DD
GROENLO DATE
HOLLAND
REV.
Ref.Nr.
Documentation released
DESCRIPTION
??
+3V3 without the+3V3
DRAWING:
in a data base or retrieval
system
prior written permission +3V3
of NEDAP.
+3V3
R474
SW
R474
R474
IN KSW
1 2
3IN KSW
100 Ω
IN KSW
100 Ω
K208
1 Keyswitch
10K Ω
+ 100
12VΩ1 for sensorsK208 10K Ω (YELLOW)
DSGN:
ARTICLE NUMBER
K3 (Not included) K208 A
8017336
10K Ω
10K Ω
K208
K208
10K Ω
Pin 1 = Gnd2External
X2 PCB
(c) by N.V.
Apparatenfabriek
NEDAP. No part of this
External
X2 PCB
5 Nederlandsche
Pin 2 = +33Volt
in Copyright
switchbox
drawing may be reproduced orswitchbox
distributed in any form or by any means, or stored
SW
APPROVED
Ref.Nr.
GROENLO HOLLAND
DESCRIPTION
C4
The latest version of the Configuration Manager must be installed for use with the new electronics The sweep time has
changed, there fore all units in a system must have firmware version 2.xxx or higher!
50 Ω (1)
ON
OFF
CC 1(TX-out)
(Yellow)
CC 2 (Yellow)
CC 2 (Yellow)
K1
Antenna
(TX-out)
Power on (Green)
K1
Antenna
CC 2 (Yellow)
CC 1(2)
(Yellow)
No function
CC 1 (Yellow)
K210
CC 2 (Yellow)
K210
Alarm (Yellow)
USB (mini) config port
Datacom error (Red)
GROENLO HOLLAND
SW3
Master/slave switch
Power on (Green)
± 0.2
ISO A
N/A
1 A
DESCRIPTION
DIM. IN MM
GENERAL TOLERANCES
LIN.
ANG.
ROUGHNESS ACC.
ISO 1302 in µM
QUICK REFERENCE X2
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
drawing may be reproduced or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission
K1of NEDAP.
Antenna
(TX-out)
DESCRIPTION
DSGN:
CB
2009-10-26
DRW:
CB
2009-10-26
GENERAL TOLERANCES
LIN. config port
ANG.
USB (mini)
ISO 1302 in µM
± 1°
GENERAL TOLERANCES
LIN.
ANG.
2009-12-18
N/A
± 0.2
ISO A
± 1°
SCALE:
FORMAT:
DESCRIPTION
CB
2009-10-26
DRW:
CB
2009-10-26
A3
CHCK:
CB
2009-12-18
ARTICLE NUMBER
OF 2
DSGN:
1:1
DIM. IN MM
REV.
5276659
45.01 OF 2
SHEET:
DRAWING:
T5276-659
Ref.Nr.
REV.
ROUGHNESS ACC.
-5-
CB
5276659
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
drawing may be reproduced or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission of NEDAP.
CB
DRW:
ARTICLE NUMBER
ANG.
Sync
outCB
CHCK:
QUICK REFERENCE X2
QUICK REFERENCE X2
1:1
LIN.
ANG.
FORMAT:
8A3
LIN.
GROENLO HOLLAND
DSGN:
2009-10-26
K210
ROUGHNESS ACC.
ISO 1302 in µM
1:1
in a data base or retrieval system without the prior written permission of NEDAP.
SHEET:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
45.01DRAWING:
OF 2SHEET:
Copyright (c)
by N.V.
Apparatenfabriek
NEDAP. No part of this
drawing may be reproduced or distributed
in any
formNederlandsche
or by any means,
or stored
6 distributed
drawing
reproduced
or
in any
or by
or SHEET:
stored
Copyright
(c) by 5system
N.V. Nederlandsche
Apparatenfabriek
NEDAP.
No form
part of
thisany means,
in a data
base or retrieval
withoutmay
the be
prior
written permission
of NEDAP.
DRAWING:
T5276-659 45.01
in K209
a dataorbase
or retrieval
without
prior
written
drawing may be reproduced
distributed
in system
any form
or bythe
any
means,
or permission
stored of NEDAP.
DRAWING:
6 without the prior written permission
5 in a data base or retrieval system
of NEDAP.
DRAWING:
Deact.
buzzer
USB (mini) config4 port
T5276-659
SW3
Master/slave switch
GENERAL TOLERANCES
SCALE:
LIN. DIM. IN MM ANG. DSGN: CB
GROENLO HOLLAND
FORMAT:
±
± 1° A3FORMAT:
CHCK: A3CB CHCK:
± 0.2ISO A
± 0.2
1°
REFERENCE
X2
5276659
ARTICLE NUMBER
REV.
ARTICLE NUMBER
ARTICLE
NUMBER
SHEET:
Copyright (c)
by N.V. Nederlandsche
NEDAP. No part of this
QUICK
REFERENCE
X2Apparatenfabriek
c 5276659
5276659
drawing may be reproduced orQUICK
distributedREFERENCE
in any form or by anyX2
means,
or stored
5276659
QUICK REFERENCE
X2ACC.
ROUGHNESS
45.01 OF 2
DRAWING:
2009-10-26
CB
K102
Sync out
DSGN:
SHEET:
DIM.
GROENLO
HOLLAND
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
45.01HOLLAND
OF 2IN MM DIM.
IN MM CB DSGN:
GROENLO
C A3
CHCK: CB
drawing may be reproduced
or distributed
or by any means,
or stored
± 0.2SCALE: 1:1
± 1° DRW:FORMAT:
2009-12-18
GENERAL
TOLERANCES
ISO A
ROUGHNESS
ACC. in any formN/A
2009-10-26
TOLERANCES
GENERAL
TOLERANCES
in a data base or retrieval system
without theACC.
prior written
permission ACC.
of
NEDAP.GENERAL
K101
ROUGHNESS
ROUGHNESS
DRAWING:
T5276-659
K102 CB SCALE:
LIN.
SCALE:
ANG.
DRW:1:1CB DRW:
ISO 1302
in µM
5276659
SHEET:
DSGN:
DIM. IN MM
GROENLO HOLLAND
K101
Sync in
K209K211
K208
SCALE:
CB buzzer
2009-10-26
Customer 1:1 DRW:Deact.
Keyswitch
FORMAT:
2009-12-18
CHCK: CB
K209 A3K209
± 0.2
± 1° counting
ISO A
K210
K209
Deact.
buzzer
Deact.
buzzer
ARTICLE
NUMBER
REV.
USB (mini)
config config
port port
USB (mini)
DIM. IN MM
GROENLO HOLLAND
Deact.
buzzer
USB (mini) config port
K210
K1 ROUGHNESS ACC.
ISO 1302 in µM
Antenna
(TX-out) N/A K210 K210
CB
A3 CHCK: SW3
Master/slaveREV.
switch
DESCRIPTION
ARTICLE NUMBER
ISOin
1302 in µM
ISO 1302 in µM
Sync
SW34
N/A 6
± 0.27
ISO A
SW3
N/A
SW3
N/A
QUICK
ISO A
Master/slave switch
DESCRIPTION
Master/slave
switch
DESCRIPTION
Master/slave switch
DESCRIPTION
USB (mini) config port
K1
Antenna
(TX-out)
FORMAT:
± 1°
CC 1 (Yellow)
1:1
SCALE:
CC 2 (Yellow)
SW3
Master/slave switch
K1
K1
Antenna
Antenna
(TX-out)
(TX-out)
K209
Deact. buzzer
K101
Sync in
YYYY-MM-DD
Pin 2 = in
+33Volt in
Pin
2 = +33Volt
4092201-rs
Pin 2 = +33Volt
in NEDAP. No part of this
SHEET:
10.01
Copyright (c) by N.V.ANederlandsche
Apparatenfabriek
Documentation released
drawing may
or distributed A
in any formYYYY-MM-DD
or by any means, or stored
N/Abe reproduced
DRAWING:
in a data base or retrieval
system withoutREV.
the prior written permission
of NEDAP.
Ref.Nr.
DATEApparatenfabriek
DESCRIPTION
Copyright (c) by N.V. Nederlandsche
NEDAP. No part of this
drawing
may
be
reproduced
or
distributed
in
any
form
or
by
any
means,
or
stored
(Not included)
External
X2 PCB
Pin 2 = +33Volt
in drawing may be reproduced
switchbox
orswitchbox
distributed in any form or by any means, or stored
SW
Keyswitch
+3V3 without the+3V3
DRAWING:
in a data base or retrieval
system
prior written permission +3V3
of NEDAP.
+3V3
R474
SW
R474
R474
IN KSW
1 2
3IN KSW
100 Ω
IN KSW
100 Ω
Ω
100
K208
1 Keyswitch
10K Ω
+ 12V for sensorsK208 10K Ω (YELLOW)
SW
Keyswitch
Circuit
diagramKeyswitch
Circuit diagram
GND
Keyswitch
ROUGHNESS ACC.
ISO 1302 in µM
GND
N/A
N/A
SHEET:
Art.No: 7706707
(Not included)
APPROVED
10.01 OF 1
K3
K3 (NotHOLLAND
DSGN:
DIM. IN MM
(YELLOW) DRAWING:
+ 12Vthe
forprior
sensors
in a data base or retrieval system without
written
permission
ofincluded)
NEDAP.
GROENLO
N/A
??
2009-MM-DD
(YELLOW)
(YELLOW)
+ sensors
12V for sensors
+ 12V for
Pin 1 = Gnd
Pin 1 = Gnd
CC sensor
3 (BLUE)
2 2 GENERAL TOLERANCES
ROUGHNESS ACC.
SCALE: 2 1:1
?? (BLUE)
2009-MM-DD
CC2sensor
DRW: (BLUE)
Pin 2 = +33Volt
in1
CC ANG.
sensor
in
CC sensor
(RED)
LIN.Pin 2 = +33Volt
ISO 1302 in µM NC (RED)
CC1sensor
1 A4
CC
sensor
Gnd
FORMAT:
(GREEN)
?? NC 2009-MM-DD
CHCK: (RED)
APPROVED
± 1° Gnd
± 0.2
ISO A
NCN/A
IN KSW
(GREEN)
YYYY-MM-DD
DSGN: ?? NC
DIM. IN MM
(GREEN)
+ 12V forGnd
sensors
REV.
DESCRIPTIONE
NUMBER
(YELLOW)
+ (YELLOW)
12V forARTICLE
sensors
CC
sensor
(BLUE)
SCALE:
1:2 ADRW: ?? YYYY-MM-DD
CC sensor 2
K206
(BLUE)
(BLUE)
YYYY-MM-DD
Documentation released
3 DATE
R474 (RED)
DESCRIPTION
IN KSW
(GREEN)
GND
Ω
100
GROENLO
HOLLAND
2. Block diagram SDR PCB
SW
CC sensor 2
GND
GND
CC sensor
R474 1
Ref.Nr. SW REV.
GND
Gnd 100 Ω
GND
OF 1
GENERAL TOLERANCES
LIN.
ANG.
N/A
4092201-rs
GND
CC sensor
(RED)
Pin 2 = - buzzer
(black)1
FORMAT: A3 CHCK: ?? YYYY-MM-DD
CC sensor
K206
(RED)
N/A
± 0.2
± 1°
K206
ISO A
K206 Gnd
Pin 1 = + buzzer
Gnd (red)
DESCRIPTION
SHEET: (black) 10.01
2(GREEN)
= - buzzer
ARTICLECopyright
NUMBER
(GREEN)
OF 1
(c)REV.
by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this Pin
Pin 2GND
= - buzzer
(black)
GND
Ω
(1)
50
Pin
buzzer
(black)
No function (2) Pin 1 = + buzzer (red)
A or distributed in any form or by any means, or stored
drawing may be reproduced
Pin
buzzer
(red)
Circuit
diagram
50 Ω (1)
8017328
Circuit diagram
N/A
ON
in a data baseA.01
or retrieval system without the prior written permissionPin
of NEDAP.
N/A
1 = + buzzerDRAWING:
(red)
No function (2)
ON
OFF
K206
SHEET:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
10.01 OF 1
K206
No function
OFF
drawing may(2)
be reproduced or distributed in any form or by any means, or stored
External
X2 PCB
Pin
buzzer
(black)
Pin 2 = - buzzer
(black)
in a data base or retrieval system without the prior written permission of NEDAP.
DRAWING:
Art.No: 7706707
N/A
(1)
50 Ωswitchbox
+3V3
Ω (1)
50+3V3
included)
Pin 1 = + buzzer (red) Pin 1 = + (Not
buzzer
(red)
ON
ON
No
function
(2)
K3
(Not included)
D OFF
No
function
(2)
K208
K211
OFF
K208
10K Ω
Circuit diagram
50 Ω (1)
ON
OFF
The X2 PCB combines the communication control unit, the transmitter and receiver in one single unit.
Alarm (Yellow)
2D
K208
Customer
counting
Pin 1 = Gnd
Pin 2 = +33Volt in
K211
Keyswitch
(Yellow)
For networkAlarm
communication
NCC (NCC MK2, SQ) is necessary.
Datacoman
errorexternal
(Red)
SW
Alarm (Yellow)
Keyswitch
R474
IN KSW
100 Ω
Alarm (Yellow)
Alarm (Yellow)
Datacom error (Red)
2.1.1 Hand-terminal-connection
CC 1 (Yellow)
Circuit diagram
CC 2 (Yellow)
Power
Datacom error
(Red)on (Green)
Datacom error (Red)
CC 2 (Yellow)
CC 1(2)
(Yellow)
No function
CC 1 (Yellow)
GROENLO HOLLAND
GENERAL TOLERANCES
LIN.
ANG.
ROUGHNESS ACC.
ISO 1302 in µM
1 A
K1
Antenna
(TX-out)
DESCRIPTION
DIM. IN MM
DSGN:
SCALE:
DRW:
FORMAT:
ISO A
ve switch
USB (mini) config port
GROENLO HOLLAND
K211
K208
Customer
counting
K211Keyswitch
Keyswitch
Keyswitch
Customer
NC
K102
counting
NC
Sync out
K101
Sync in
K101
Sync in
DSGN:
DIM. IN MM
K101
Sync in
2009-10-26
CB
K102
Sync out
K209K211
GENERAL TOLERANCES K208
K1 ROUGHNESS ACC.
SCALE:
CB buzzer
2009-10-26
1:1 DRW:Deact.
Keyswitch
LIN. config port
ANG. Customer
USB (mini)
ISO 1302 in µM
Antenna
counting
FORMAT:
2009-12-18
CB
A3
CHCK:
K209
K209
± 0.2
± 1°
(TX-out) N/A K210 K210 ISO A
K210
K209
Deact. buzzer
DESCRIPTION
Deact.
buzzerDeact.
ARTICLE NUMBER
REV.
USB (mini)
config config
port port
USB (mini)
DIM. IN MM
GROENLO HOLLAND
buzzer
2009-10-26
USB (mini) config port
K210
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
drawing may be reproduced or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission of NEDAP.
ARTICLE NUMBER
SHEET:
DRAWING:
DSGN:
GENERAL TOLERANCES
SCALE:
DRW:
LIN. DIM. IN MM ANG. DSGN:
GROENLO HOLLAND
SHEET:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
DIM.
GROENLO HOLLANDFORMAT:
C IN MMCHCK: DSGN:
drawing may be reproduced
or distributed
or stored
GENERAL
TOLERANCES
ISO A
ROUGHNESS
ACC. in any form or by any means,
SCALE:
DRW:
in a data base or retrieval system without the prior written
permission of
NEDAP.
DRAWING: GENERAL TOLERANCES
SCALE: ARTICLE NUMBER
LIN.
ANG.
DRW:
ISO 1302 in µM DESCRIPTIONROUGHNESS ACC.
LIN.
ANG.
REV.
ISO 1302 in µM
FORMAT: 8
CHCK:
ISO A
FORMAT:
CHCK:
ISO A
DESCRIPTION
ARTICLE NUMBER
REV.
DESCRIPTION
ARTICLE NUMBER
SHEET:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
drawing may be reproduced or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission of NEDAP.
DRAWING:
SHEET:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
SHEET:
Copyright (c)
by N.V.
Apparatenfabriek
NEDAP. No part of this
drawing may be reproduced or distributed
in any
formNederlandsche
or by any means,
or stored
6 distributed
reproduced
or
in any form or by
any means,
or stored
in a data base or retrieval systemdrawing
withoutmay
the be
prior
written permission
of NEDAP.
DRAWING:
in a data base or retrieval system without the prior written permission of NEDAP.
DRAWING:
ROUGHNESS ACC.
ISO 1302 in µM
CHCK:
GROENLO HOLLAND
GENERAL TOLERANCES
LIN.
ANG.
ROUGHNESS ACC.
ISO 1302 in µM
K208
K208 Customer
counting
Customer
K211
counting K208
USBimportant
(mini) config portfeatures of the X2 electronics is the data-com over the coax
One of the
SW3
CB
cable. With this featureDatacom
it’s not
necessary toMaster/slave
use answitch
extra data-cable
between the
error (Red)
CB
QUICK REFERENCE X2
5276659
CB
1:1
CB
2009-10-26
1:1
2009-10-26
CB
units, which simplifies Power
the oninstallation
of the system. An NCC MK2 unit plays a
DSGN: CB
GROENLO HOLLAND45.01 DIM.
OF 2IN MM
(Green)
CB
A3
SW3
N/A
± 0.2
± 1°
2009-12-18
CB
A3
N/A
± 0.2
± 1°
CB
2009-10-26
1:1
GENERAL TOLERANCES T5276-659
K101
ROUGHNESS ACC.
K102 1:1
SCALE:
DRW:1:1CB
central roll in providing the data-com.
All
the connected
units
are
interrogated
Master/slave
switch
LIN.
ANG.
ISO 1302 in µM
Sync
in
Sync
out
2009-12-18
CB
A3
SW3
CC 1 (Yellow)
N/A
± 0.2
± 1°
A3CB
FORMAT:
SW3
N/A
±
± 1° A3 CHCK:
SW3
± 0.2
± 0.2
1°
QUICK
REFERENCE
X2
ISO A
5276659
QUICK
Master/slave
switch on a c
periodically by this
unit. IfREFERENCE
there areX2messages like
an5276659
alarm
connected X2 N/A
CC 2 (Yellow)
Master/slave switch Master/slave switch DESCRIPTION
ARTICLE NUMBER
OF 2
REFERENCE
X2 REFERENCE X25276659
c 5276659
QUICK
unit, then the NCC MK2 unit will process this and takes the45.01necessary
action: QUICKQUICK
REFERENCE
X2
5276659
T5276-659
K1
45.01
OF 2
Sending a command to turn on the lampsAntenna
on the activated aisle.
SHEET:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
T5276-659 45.01 OF
drawing may be reproduced
(TX-out)
K210
K209or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission of NEDAP.
DRAWING:
Deact. buzzer
The X2 has two slave-sync connectors (K101 and K102) from whichUSBthe
(mini)unit
config can
port be
driven from a NCC MK2, SQ, DQ or another networking unit.
2009-10-26
CB
Alarm (Yellow)
K1
K1
Antenna
Antenna
(TX-out)
(TX-out)
K209
Deact. buzzer
K210
K210
CC 2 (Yellow)
CC 2 P
(Yellow)
2.1.2 Data communication
over coax and
ower
K206
Pin 2 = - buzzer (black)
Pin 1 = + buzzer (red)
K101
Sync in
K209
Deact. buzzer
Antenna
CC 1(TX-out)
(Yellow)
CC 2 (Yellow)
Keyswitch
(YELLOW)
(BLUE)
(RED)
(GREEN)
+ 12V for sensors
CC sensor 2
CC sensor 1
K101
Gnd
Sync in
K102
Sync out
in
1(Green)
(Yellow)
PowerCC
onSync
ON
OFF
Customer
counting
K101
Power on (Green)
The50use
the X2 unit.
Ω (1) of a handheld terminal is not available
Powerfor
on (Green)
K1
Datacom error (Red)
Power on (Green)
GND
GND
NC
NC
2.1 Network communication control
SW3
Master/slave switch
N/A
± 0.2
ISO A
± 1°
DSGN:
DIM. IN MM
SCALE:
FORMAT:
1:1
DRW:
CB
2009-10-26
A3
CHCK:
CB
2009-12-18
X2 electronics can also act as a stand-alone unit, without the need for any synchronization. DC power supply always from its
QUICK REFERENCE X2
5276659
own Master DC input connector K3 or from the power inserter.
DESCRIPTION
ARTICLE NUMBER
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
drawing may be reproduced or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission of NEDAP.
SHEET:
REV.
2.2 Anti-deactivation regulation
A (Detection mode)
DRAWING:
45.01 OF 2
T5276-659
To prevent unwanted deactivation during detection of a label, the transmitted power will be reduced when a label is in its
proximity. It is a high speed loop. The user will not notice a difference in response.
2.3 Tag Analyzer
In tag analyzer mode, the power is constant. The tag analyzer has the ability to detect, store label information, like accurate Q
and frequency measurement. It can also measure differences in deactivation levels.
Ref.Nr.
REV.
By using a piezo a label can be detected, the signal strength will be visualized by a repeating audio signal. When a label is
no longer detected, the gathered information will be stored. When a low Q label is detected, the transmitterROUGHNESS
signal willACC.
be
increased; the label will be quicker deactivated.
2.4 Transceiver section
The X2 makes use of the pulse (transmitter) and listen (receiver) technique. This is the same technique used with radar. This
gives the freedom to use it with mono-antennas.
The X2 uses a transceiver architecture that gives the highest flexibility possible today. The analog signal from the antenna is
almost directly converted to digital domain. The transmitter signal is just before the antenna converted to analog.
The analog to digital converter (ADC) has a high dynamic range and runs on a high frequency. This gives the possibility to
handle strong interference without clipping/distorting the wanted label signal in the receiver.
The antenna is connected to K1.
When a single unit X2 is stand-alone no synchronization is necessary. In all other situations the transceiver needs to be
synchronized for best performance.
-6-
YYYY-MM
The receiver receives its RF reference signal and configuration data from the local
communication control section.
Transmitter:
Although the effective RF power is in the same range as our high power swept
system, the peak signals are much higher. As a consequence of that, the label
can be deactivated at larger distances from the antenna compared to the swept
system. For that reason the X2 has an RF power-control. This control will reduce it’s
transmit power when it detects a label within the deactivation range. Interferences
like a swept system will be suppressed from influencing the power-control.
In the label analyzer mode the TX power will not decrease, but increase when a low
Q-factor label is brought into the detection field.
K1
Antenna (Tx-out)
SW3
Master/slave switch
Receiver:
The selectivity and dynamic range is very high. The selectivity is achieved with advanced high-speed digital filter techniques.
This gives the advantages to be able to work in environments with large level interferences.
2.5 Master - Slave settings and status LEDs
Changing the unit functionality between slave and master can be done by pushing
button SW3. (See page 20)
Alarm(Yellow)
Datacom error(Red)
2.5.1 View X2 electronics Status
Press button SW3 1x (See page 20).
• When the yellow LED starts to blink and the red LED burns continiously, the X2 is set as a slave.
• When both LED’s are blinking, the X2 is set as master.
2.5.2 Change X2 functionality
Press button SW3 (See page 20) 2x within 5 seconds to switch to master (or slave) status. The X2 electronics is standard
programmed as slave.
2.6 X2 approved antennas
Nedap has a broad range of antennas. Not all antennas are approved in combination with the X2 electronics. In the near
future more and more antennas will be X2 ready. It is important to know that only HIGH POWER antenna’s can be used for
safety reasons.
At the time of writing this document the following Nedap antennas are approved for use with X2 electronics:
• FL30
• FL45
• D40
• D50
• PG27
• PG39
• EQ45-F
-7-
3
2D
Alarm (Yellow)
SW
Alarm (Yellow)
Keyswitch
+3V3
Ω (1)
50+3V3
ON
(2)
OFFNo function10K
Ω
K208
Alarm (Yellow)
in a data base or retrieval system without the prior written permission of NEDAP.
(1)
50 Ωswitchbox
ON
D OFF
K3 (Not included)
Pin 1 = Gnd
Pin 2 = +33Volt in
No function (2)
K208
Customer
counting
R474
Datacom error (Red)
IN KSW
100 Ω
Power on (Green)
2.7Alarm
Data
communication
(Yellow)
Alarm (Yellow)
Pin 2 = - buzzer (black)
Pin 1 = + buzzer (red)
N/A
DRAWING:
K211
Keyswitch
K208
Customer
counting
Datacom error (Red)
GND
CC 1 (Yellow)
Circuit diagram
Power
Datacom error
(Red)on (Green)
Datacom error (Red)
K211
Keyswitch
K208
(YELLOW)
(BLUE)
(RED)
(GREEN)
+ 12V for sensors
CC sensor 2
CC sensor 1
K101
Gnd
Sync in
Datacom error (Red)
GND
Pin 2 = - buzzer
(black)
Art.No: 7706707
included)
Pin 1 = + (Not
buzzer
(red)
K208
Customer
counting
Keyswitch
Customer
NC
K102
counting
NC
Sync out
Master/slave switch
Datacom error (Red)
GROENLO HOLLAND
CB
X2
The X2 PCB is prepared with customer
Sensors
connected to monitor 1 entrance with direction sensitivity.
The passage between sensors is shaped and buffered and processed by the
processor.
In this way 2incoming and outgoing
label alarms
can be counted
for
separately.
SW3
± 0.2
ISO A
DESCRIPTION
1:1
SCALE:
A3
FORMAT:
± 1°
35
64
Ref.Nr.
01
External
switchboxX2 PCB
External
switchbox
F F
REV.
3Documentation released
YYYY-MM-DD
DATE
Copyright (c) by N.V. Nederlandsche
Apparatenfabriek NEDAP. No part of this
drawing may be reproduced or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission of NEDAP.
64
5 3
5 7
APPROVED
Ref.Nr.
GROENLO HOLLAND
X2 PCB
X2 PCB
External
ROUGHNESS
ACC.
switchbox
ISO 1302
in µM
+3V3
+3V3
1 N/A
B5
DESCRIPTION
GENERAL TOLERANCES
ANG.
LIN.
+3V3 +3V3
± 0.2 2 3
+3V3 ISO A
DIM. IN MM
SCALE:
+3V3 FORMAT:
± 1°
1:1
A4
REV.
YYYY-MM-DD
DATE
2009-MM-DD
??
DRW:
?? 2009-MM-DD
GENERAL TOLERANCES
ROUGHNESS ACC.
ANG.
LIN.
Art.No:
7706707
ISO 1302
in µM
?? 42009-MM-DD
(NotN/A
included)
ROUGHNESS
± 1°
± 0.2
ISO A 4ACC. 5
CHCK:
K3 (Not included) K208 A
8017336
10K Ω
10K Ω
K208
K208
10K Ω
Pin 1 = Gnd2External
X2 PCB
(c) by N.V.
Apparatenfabriek
NEDAP. No part of this
External
X2 PCB
5 Nederlandsche
Pin 2 = +33Volt
in Copyright
switchbox
drawing may be reproduced orswitchbox
distributed in any form or by any means, or stored
SW
SW
Keyswitch
Keyswitch
Circuit
diagramKeyswitch
Circuit diagram
2.9 DC Power Supply
50 Ω (1)
ON
OFF
50 Ω (1)
ON
OFF
(BLUE)
GND 4
YYYY-MM-DD
Documentation released
3 DATE
R474 (RED)
DESCRIPTION
IN KSW
(GREEN)
GND
Ω
100
GROENLO
HOLLAND
GND
Keyswitch
GENERAL TOLERANCES
ROUGHNESS ACC.
LIN.
ANG.
ISO 1302 in µM
GND
GND
N/A
± 0.2
± 1°
K206
ISO A
DESCRIPTION
Pin 2GND
= - buzzer
(black)
GND
GND
CC sensor
R474 SW
Ref.Nr.
GND
Gnd 100 Ω
Circuit diagram
ON
OFF
External
X2 PCB
Ref.Nr.
ISO 1302 in µM
REV.
K208
Alarm (Yellow)
SW
Alarm (Yellow)
Keyswitch
2D
Alarm (Yellow)
SHEET:
DRAWING:
CC 1 (Yellow)
Circuit diagram
50 Ω (1)
ON
OFF
CC 2 (Yellow)
No function (2)
CC 1 (Yellow)
Alarm (Yellow)
USB (mini) config port
Datacom error (Red)
GROENLO HOLLAND
DIM. IN MM
2009-MM-DD
Art.No: 7706707
?? 62009-MM-DD
(Not included)
(Not included)
78
Art.No: 7706707
(Not included)
N/A
SHEET:
APPROVED
K1
Antenna
(TX-out)
DSGN:
CB
YYYY-MM-DD
K208
K211
counting
ROUGHNESS
ACC.
Customer
K208
counting
Customer
counting
K102
K206
Pin 2 = - buzzer (black)
Pin 1 = + buzzer (red)
K101
Sync in
K209
Deact. buzzer
USB (mini) config port
GROENLO HOLLAND
K211
K208
Keyswitch
Customer
NC
counting
NC
Sync out
NC
NC
N/A
K211
Keyswitch
(YELLOW)
(BLUE)
(RED)
(GREEN)
K211Keyswitch
Keyswitch
K101
Sync in
K101
Sync in
DSGN:
DIM. IN MM
K101
Sync in
2009-10-26
CB
K102
Sync out
K210
K209K211
GENERAL TOLERANCES K208
K1 ROUGHNESS ACC.
SCALE:
CB buzzer
2009-10-26
1:1 DRW:Deact.
Keyswitch
LIN. config port
ANG. Customer
USB (mini)
ISO 1302 in µM
Antenna
counting
FORMAT:
2009-12-18
CB
A3
CHCK:
K209
K210
N/A
K210
K209
±
0.2
±
1°
ISO A
(TX-out)
K210
K209
Deact. buzzer
DESCRIPTION
Deact.
buzzerDeact.
ARTICLE NUMBER
REV.
USB (mini)
config config
port port
USB (mini)
DIM. IN MM
GROENLO HOLLAND
buzzer
2009-10-26
USB (mini) config port
5276659
QUICK REFERENCE
X2ACC.
ROUGHNESS
DSGN:
CB
GENERAL TOLERANCES
SCALE:
1:1 DRW: CB
LIN. DIM. IN MM ANG. DSGN: CB
2009-10-26
GROENLO HOLLAND
DSGN:
SHEET:
DIM.
GROENLO
HOLLAND
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
45.01HOLLAND
OF 2IN MM DIM.
IN MM CB DSGN:
Power on (Green)
GROENLO
C A3
CHCK: CB
FORMAT: A3 CHCK: SW3
drawing may be reproduced
or distributed
or by any means,
or stored
± 0.2SCALE: 1:1
± 1° DRW:FORMAT:
2009-12-18
CB
GENERAL
TOLERANCES
ISO A
ROUGHNESS
ACC. in any formN/A
N/A
± 0.2
± 1°
ISO A
CB
2009-10-26
TOLERANCES
GENERAL
TOLERANCES
in a data base or retrieval system
without theACC.
prior written
permission ACC.
of
NEDAP.GENERAL
K101
ROUGHNESS
ROUGHNESS
DRAWING:
T5276-659
K102
SCALE:
LIN.
SCALE:
ANG.
1:1CB
DRW:
1:1
DRW:
ISO
1302
in
µM
Master/slaveREV.
switch
DESCRIPTION
ARTICLE
NUMBER
DESCRIPTION
LIN.
ANG.
ARTICLE NUMBER
LIN.
ISOin
1302 in µM
ANG.
ISO
1302
in
µM
Sync
Sync
out
FORMAT:
8A3 CHCK: CB
2009-12-18
SW34
CC 1 (Yellow)
N/A 6
± 0.27
± 1°
ISO A
FORMAT:
FORMAT:
SW3
N/A
±
± 1° A3 CHCK: A3CB CHCK:
SW3
N/A
± 0.2ISO A
± 0.2
1°
ISO A
Master/slave
switch
DESCRIPTION
ARTICLE
NUMBER
REV.
CC 2 (Yellow)
DESCRIPTION
ARTICLE NUMBER
Master/slave switch Master/slave switch DESCRIPTION
ARTICLE
NUMBER
SHEET:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
SHEET:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
45.01 OF 2
drawing may be reproduced or distributed in any form or by any means, or stored
drawing may be reproduced or distributed in any form or by any means, or stored
in
data
base
or
retrieval
system
without
the
prior
written
permission
of
NEDAP.
DRAWING:
in a data base or retrieval system without the prior written permission
DRAWING:
SHEET:
T5276-659
K1of NEDAP.
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
45.01 OF 2SHEET:
Copyright (c)
by N.V.
Apparatenfabriek
NEDAP. No part of this
drawing may be reproduced or distributed
in any
formNederlandsche
or by any means,
or stored
6 distributed
Antenna
drawing
reproduced
or
in any
or by
or SHEET:
stored
Copyright
(c) by 5system
N.V. Nederlandsche
Apparatenfabriek
NEDAP.
No form
part of
thisany means,
in a data
base or retrieval
withoutmay
the be
prior
written permission
of NEDAP.
DRAWING:
T5276-659 45.01 OF
in K209
a dataorbase
or retrieval
without
prior
written
drawing may be reproduced
distributed
in system
any form
or bythe
any
means,
or permission
stored of NEDAP.
DRAWING:
(TX-out)
K210
6 without the prior written permission
5 in a data base or retrieval system
of NEDAP.
DRAWING:
Deact.
buzzer
USB (mini) config4 port
GENERAL TOLERANCES
LIN.
ANG.
ROUGHNESS ACC.
ISO 1302 in µM
SW3
Master/slave switch
SCALE:
1:1
DRW:
CB
2009-10-26
5276659
QUICK REFERENCE X2
K1
K1
Antenna
Antenna
(TX-out)
(TX-out)
SW3
Master/slave switch
APPROVED
K210
CC 2 (Yellow)
K208 Customer
K102
Sync out
Power on (Green)
K209
Deact. buzzer
K210
2009-MM-DD
K208
Customer
counting
K1
Antenna
??SCALE:
2009-MM-DD
1:1 DRW:
+ 12V for sensors
CC sensor 2
CC sensor 1
K101
Gnd
Sync in
CC 1(TX-out)
(Yellow)
CC 2 (Yellow)
K206
K206
A 4
3Pin 2 = - buzzer (black)
Pin 2 = - buzzer
(black)
Art.No: 7706707
included)
Pin 1 = + buzzer
(red) Pin 1 = + (Not
Ref.Nr.
REV.
buzzer
(red)
K3 (Not included)
Pin 1 = Gnd
Pin 2 = +33Volt in
counting
K101
Power on (Green)
in
1(Green)
(Yellow)
PowerCC
onSync
CC 2 (Yellow)
CC 1 (Yellow)
??DIM. 2009-MM-DD
DSGN: ??
IN MM
SCALE:
DRW:
GROENLO 1:1
HOLLAND
Power
Datacom error
(Red)on (Green)
Datacom error (Red)
CC 2 (Yellow)
K1
Antenna
(TX-out)
??
GENERAL
A4 5 CHCK:
FORMAT:TOLERANCES
ANG.
LIN.
N/A
Datacom error (Red)
Power on (Green)
CC 1(Yellow)
CC 2(Yellow)
APPROVED
R474
GND
T5276-659
10.01 OF 1
No function (2)
Alarm (Yellow)
45.01 OF 2
N/A
in a data baseA.01
or retrieval system without the prior written permissionPin
of NEDAP.
1 = + buzzerDRAWING:
(red)
+3V3
Datacom error (Red)
IN KSW
2x cM4x10 A
N/A
in a data base or retrieval system without the prior written permission of NEDAP.
100 Ω
REV.
Datacom error (Red)
GND
2009-12-18
10.01 OF 1
K3
K3 (NotHOLLAND
DSGN:
DIM. IN MM
(YELLOW) DRAWING:
+ 12Vthe
forprior
sensors
in a data base or retrieval system without
written
permission
ofincluded)
NEDAP.
GROENLO
N/A
No function
drawing may(2)
be reproduced or distributed in any form or by any means, or stored
ON
(2)
OFFNo function10K
Ω
CB
DRAWING:
Power over synchronization is possible for X2. DC supply always from its own
K208
K211
Master DC input connector K3 orAlarm
from
a power inserter . Customer
(Yellow)
Keyswitch
CHCK:
drawing may
or distributed in any form or by any means, or stored
N/Abe reproduced
DRAWING:
in a data base or retrieval
system withoutREV.
the prior written permission
of NEDAP.
Ref.Nr.
DATEApparatenfabriek
DESCRIPTION
Copyright (c) by N.V. Nederlandsche
NEDAP. No part of this
drawing may be reproduced
or distributed in any3form or by any means, or stored4
(Not included)
+ buzzer 8017328
(red)
No function (2)
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
Ω (1)
50+3V3
2009-10-26
?? 2009-MM-DD
(YELLOW)
+ sensors
12V for sensors (YELLOW)
+ 12V
for
PinB1 = Gnd
PinTOLERANCES
1 = Gnd
CC sensor
3 (BLUE)
2 2 GENERAL
ROUGHNESS ACC.
SCALE: 2 1:1
?? (BLUE)
2009-MM-DD
CC2sensor
DRW: (BLUE)
Pin 2 = +33Volt
in1
CC ANG.
sensor
Pin 2 = +33Volt
in
CC
sensor
(RED)
LIN.
ISO 1302 in µM NC (RED)
CC
sensor
CC
sensor
Gnd
(GREEN)
?? NC 2009-MM-DD
± 1° GndFORMAT: A4 CHCK: (RED)
± 0.2
ISO A
NCN/AAPPROVED
IN KSW
(GREEN)
YYYY-MM-DD
Gnd
DSGN: ?? NC
DIM. IN MM
(GREEN)
(YELLOW)
12V
for
sensors
REV.
DESCRIPTIONE
+ 12V forARTICLE
sensorsNUMBER (YELLOW)
CC sensor 2
(BLUE)
SCALE:
1:2 ADRW: ?? YYYY-MM-DD
CC sensor
K206
(BLUE)
4092201-rs
CC sensor
(RED)
Pin 2 = - buzzer
(black)1
FORMAT: A3 CHCK: ?? YYYY-MM-DD
CC sensor
K206
(RED)
K206 Pin
Pin 1 = + buzzer
Gnd (red)
(GREEN)
Gnd
SHEET:
buzzer
(black)
ARTICLECopyright
NUMBER
REV.
(GREEN)
10.01
OF 1
(c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
7 or
Pin
2 stored
= -Pin
buzzer
A or distributed in any form or by any means,
drawing
may be reproduced
1 = +(black)
buzzer 8(red)
50
E Ω (1)2
(2) Pin 1 =
Circuit diagram No function
Circuit diagram
(1)
50 Ωswitchbox
ON
D OFF
SHEET:
CC sensor 2
GND
SW
CB
ARTICLE NUMBER
A4 CHCK: ?? 2009-MM-DD
FORMAT: REV.
K3
N/A
K3
± 0.2(Not included)± 1°
ISO A(Not included)
K3 (Not included)
AB
AARTICLE ANUMBER
REV.
Pin 1 = Gnd
PinDESCRIPTION
1 =4092201-rs
Gnd
Pin 1 = GndN/A
10.01 OF 1
Pin 2 = +33Volt
in NEDAP.
SHEET:
Pin
2 = in
+33Volt
in 10.01 OF 1 N/A
Pin
2 part
= +33Volt
Copyright (c) by N.V.ANederlandsche
Apparatenfabriek
No
of this
4092201-rs
YYYY-MM-DD
Documentation released
+3V3 without the+3V3
DRAWING:
in a data base or retrieval
system
prior written permission +3V3
of NEDAP.
+3V3
R474
SW
R474
R474
IN KSW
1 2
3IN KSW
100 Ω
IN KSW
100 Ω
K208
1 Keyswitch
10K Ω
+ 100
12VΩ1 for sensorsK208 10K Ω (YELLOW)
REV.
DESCRIPTION
DRW:
SHEET:
Documentation released
DSGN:
DIM. IN MM
DESCRIPTION
YYYY-MM-DD
GROENLO DATE
HOLLAND
REV.
DSGN:
ARTICLE NUMBER
2009-10-26
Documentation released
DESCRIPTION
N/A
Two customer1 counting status LED’s are situated on the PCB to indicate
if the
sensors are fully functional.
DESCRIPTION
CB
2x M3x105276659
2x M3x6
2 4
DSGN:
ARTICLE NUMBERC
The sensor power output is 12 V dc. It is possible to connect sensor with positive or
negative going output signals. A
DIM. IN MM
Cable 2 FR + MD
QUICK REFERENCE
X2
Buzzer with cable
Unit X2
GROENLO HOLLAND
GENERAL TOLERANCES
LIN.
ANG.
N/A
Master/slave switch
The customer counting wires can be connected
to connector K208.
5276659
QUICK REFERENCE X2
ROUGHNESS ACC.
ISO 1302 in µM
5276659
c 5276659
QUICK REFERENCE X2
can be
QUICK REFERENCE
X2 REFERENCE X25276659
QUICK
DSGN:
5276659
QUICK REFERENCE
X2ACC.
ROUGHNESS
counting5276659
on board. c2
QUICK REFERENCE X2
DRW:
CHCK:
Deact.
buzzer
Deact.
buzzer
ARTICLE3 NUMBER
REV. 4
USB (mini)
config
port port
USB (mini)
config
DIM. IN MM
GROENLO
HOLLAND
Deact.
buzzer
USB 2(mini) config port
DESCRIPTION
2.8 Customer counting
itch
SCALE:
FORMAT:
GENERAL TOLERANCES
GENERAL TOLERANCES
SCALE:
1:1 DRW: CB
ROUGHNESS ACC.
SCALE:
2009-10-26
1:1 DRW: CB
LIN. DIM. IN MM ANG. DSGN: CB
ISO 1302 in µM
2009-10-26
GROENLO HOLLAND
LIN.
ANG.
ISO 1302 in µM
DSGN:
SHEET:
DIM.
MM DIM.
GROENLO
HOLLAND
Copyright (c) by N.V. Nederlandsche Apparatenfabriek
NEDAP. No part of this
45.01HOLLAND
OF 2INFORMAT:
IN MM CB DSGN:
Power on (Green)
GROENLO
F C A3
CHCK: CB
FORMAT: A3 CHCK: SW3
drawing may be reproduced
or distributed
or by any means,
or stored
± 0.2SCALE: 1:1
2009-12-18
CB
GENERAL
TOLERANCES
ISO A
F ± 1°
ROUGHNESS
ACC. in any formN/A
N/A
± 0.2
± 1°
ISO A
2009-10-26
DRW: CB
TOLERANCES
GENERAL
TOLERANCES
in a data base or retrieval system
without
theACC.
prior written
permission ACC.
of
NEDAP.GENERAL
K101
ROUGHNESS
ROUGHNESS
DRAWING:
T5276-659
K102
SCALE:
LIN.
SCALE:
ANG.
1:1CB
DRW:
1:1
DRW:
ISO 1302 in µM DESCRIPTION
Master/slaveREV.
switch
ARTICLE
NUMBER
DESCRIPTION
LIN.
ANG.
ARTICLE
NUMBER
LIN.
ISO
1302
in
µM
ANG.
ISO 1302 in µM
Sync in
outCB
FORMAT: 8A3 Sync
2009-12-18
CHCK:
1 A
SW34
CC 1 (Yellow)
N/A 6
±
0.2
±
1°
ISO
FORMAT:
A3
CHCK:
FORMAT:
A 7
N/A
6 SW3
CB
A3
±
0.2
±
1°
CHCK:
ISO
SW3
N/A
± 0.2
± 1°
ISO A
Master/slave switch
DESCRIPTION
ARTICLE NUMBER
REV.
CC 2 (Yellow)
DESCRIPTION
ARTICLE NUMBER
Master/slave switch Master/slave switch DESCRIPTION
ARTICLE
NUMBER
SHEET:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
SHEET:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
45.01 OF 2
drawing may be reproduced or distributed in any form or by anyE means, or stored E
drawing may be reproduced or distributed in any form or by any means, or stored
E in a data base or retrieval system without the prior written permission of NEDAP.
in a data base or retrieval system without the prior written permission
DRAWING:
SHEET:
T5276-659
K1of NEDAP.
Copyright (c) by N.V. Nederlandsche Apparatenfabriek
NEDAP. No part of this
45.01DRAWING:
OF 2SHEET:
Copyright (c)
by N.V.
Apparatenfabriek
NEDAP. No part of this
drawing may be reproduced or distributed
in any
formNederlandsche
or by any means,
or stored
6 distributed
Antenna
drawing
reproduced
or
in any
or by
or SHEET:
stored
Copyright
(c) by 5system
N.V. Nederlandsche
Apparatenfabriek
NEDAP.
No form
part of
thisany means,
in a data
base or retrieval
withoutmay
the be
prior
written permission
of NEDAP.
DRAWING:
T5276-659 45.01 OF
in K209
a dataorbase
or retrieval
without
prior
written
drawing may be reproduced
distributed
in system
any form
or bythe
any
means,
or permission
stored of NEDAP.
DRAWING:
(TX-out)
K210
6 without the prior written permission
5 in a data base or retrieval system
of NEDAP.
DRAWING:
Deact.
buzzer
USB (mini) config4 port
GENERAL TOLERANCES
LIN.
ANG.
FISO A
2009-10-26
CB
DSGN:
DIM. IN MM
DSGN:
DIM. IN MM
GROENLO HOLLAND
ROUGHNESS ACC.
ISO 1302 in µM
K211Keyswitch
Keyswitch
2 (Yellow)
K101
The X2 uses theCCsame
communication
and synchronization signals
as the sweep K206
system of Nedap Retail.
The transceiver is
K101
K102
Power on (Green)
Sync in
in
Sync out
Pin 2 = - buzzer (black)
1(Green)
(Yellow)
PowerCC
onSync
K101
50 Ω (1)
Power
on
(Green)
Pin
buzzer
(red)
aONslave. Slaves are polled byCC the
master.K1The communication control section, which is the master
unit,
pollsK101
periodically K102
all
K101
Sync in
CC 1(2)
(Yellow)2 (Yellow)
No function
OFF
Antenna
Sync in
Sync out
CC 1 (Yellow)
Sync in
(TX-out)
connected slaves CC
and
relays
data
to
other
devices
e.q.
other
control
units
or
PC’s.
CC
(Yellow)
K210
K209
2 (Yellow)
CC 2 (Yellow)
Deact. buzzer
USB (mini) config port
CC 2 (Yellow)
K1
With every sweep one slave is polled.
The polled slaveAntenna
must answer,
this happens
2009-10-26
CB
K1
(TX-out)
K209K211
K1
K209 answer data
in theK210
same sweep. These poll and
packets
are K1used implement K210
the
K208
CB buzzer
2009-10-26
1:1
Deact.
Antenna
Customer
Keyswitch
Deact.
buzzer
Alarm (Yellow)
Antenna
USB
(mini)
config
port
USB (mini) config port
Antenna
(TX-out)
(TX-out)
2009-12-18
CB
SW3
network
functionality.
K209 A3K209
± 0.2
± 1° counting
(TX-out) N/A K210 K210
K210
K209
K211
K208 Customer
counting
Customer
K211
counting K208
ISO 1302 in µM
QUICK REFERENCE
X2 REFERENCE X25276659
QUICK
5276659
QUICK REFERENCE X2
GROENLO HOLLAND
GENERAL TOLERANCES
LIN.
ANG.
ROUGHNESS ACC.
ISO 1302 in µM
SW3
Master/slave switch
N/A
± 0.2
ISO A
± 1°
SCALE:
FORMAT:
DESCRIPTION
CB
2009-10-26
1:1
DRW:
CB
2009-10-26
A3
CHCK:
CB
2009-12-18
ARTICLE NUMBER
REV.
5276659
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
drawing may be reproduced or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission of NEDAP.
DSGN:
DIM. IN MM
QUICK REFERENCE X2
5276659
c 5276659
QUICK REFERENCE X2
SHEET:
45.01 OF 2
T5276-659
DRAWING:
-8-
YYYY-MM
D
3. PCB Components overview
3.1 Connector overview
External
F F
REV.
3Documentation released
YYYY-MM-DD
DATE
X2 PCB
External
ROUGHNESS
ACC.
switchbox
ISO 1302
in µM
+3V3
GENERAL TOLERANCES
ANG.
LIN.
+3V3 +3V3
± 0.2 2 3
+3V3 ISO A
DIM. IN MM
SCALE:
+3V3 FORMAT:
± 1°
1:1
A4
YYYY-MM-DD
DATE
2009-MM-DD
??
?? 2009-MM-DD
GENERAL TOLERANCES
ROUGHNESS ACC.
ANG.
LIN.
Art.No:
7706707
ISO 1302
in µM
?? 42009-MM-DD
(NotN/A
included)
ROUGHNESS
± 1°
± 0.2
ISO A 4ACC. 5
N/A
SHEET:
REV.
DESCRIPTION
ISO 1302 in µM
50 Ω (1)
ON
OFF
ON
OFF
Alarm (Yellow)
APPROVED
??
2009-MM-DD
APPROVED
2009-MM-DD
??DIM. 2009-MM-DD
DSGN: ??
IN MM
SCALE:
DRW:
GROENLO 1:1
HOLLAND
GENERAL
A4 5 CHCK:
FORMAT:TOLERANCES
ANG.
LIN.
Art.No: 7706707
?? 62009-MM-DD
(Not included)
??SCALE:
2009-MM-DD
1:1 DRW:
78
N/A
Alarm (Yellow)
Keyswitch
K208
2D
Datacom error (Red)
IN KSW
GND
CC 2 (Yellow)
K211
Keyswitch
Power
Datacom error
(Red)on (Green)
Datacom error (Red)
CC 2 (Yellow)
CC 1(2)
(Yellow)
No function
CC 1 (Yellow)
CC 2 (Yellow)
CC 2 (Yellow)
Power on (Green)
K1
Antenna
CC 1(TX-out)
(Yellow)
K210
CC 2 (Yellow)
Alarm (Yellow)
USB (mini) config port
Datacom error (Red)
GROENLO HOLLAND
K1
K1
Antenna
Antenna
(TX-out)
(TX-out)
K209
Deact. buzzer
K210
SW3
Master/slave switch
DIM. IN MM
K208
(YELLOW)
(BLUE)
(RED)
(GREEN)
K206
Pin 2 = - buzzer (black)
Pin 1 = + buzzer (red)
K101
Sync in
K209
Deact. buzzer
K1
Antenna
(TX-out)
DSGN:
CB
USB (mini) config port
GROENLO HOLLAND
K211
Keyswitch
K208 Customer
counting
Customer
K211
counting K208
K208
Customer
counting
K102
Sync out
N/A
K206
Pin 2 = - buzzer
(black)
Art.No: 7706707
included)
Pin 1 = + (Not
buzzer
(red)
K208
Customer
counting
+ 12V for sensors
CC sensor 2
CC sensor 1
K101
Gnd
Sync in
K101
Power on (Green)
in
1(Green)
(Yellow)
PowerCC
onSync
C 50 Ω (1)
ON
OFF
N/A
K3 (Not included)
Pin 1 = Gnd
Pin 2 = +33Volt in
Datacom error (Red)
CC 1 (Yellow)
Circuit diagram
K206
Pin 2 = - buzzer (black)
Pin 1 = + buzzer (red)
Datacom error (Red)
Power on (Green)
GND
DRAWING:
K208
Customer
counting
R474
Alarm (Yellow)
No function (2)
100 Ω
Alarm (Yellow)
in a data base or retrieval system without the prior written permission of NEDAP.
10.01 OF 1
SHEET:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
No function
drawing may(2)
be reproduced or distributed in any form or by any means, or stored
+3V3
Ω (1)
50+3V3
ON
(2)
OFFNo function10K
Ω
10.01 OF 1
N/A
in a data baseA.01
or retrieval system without the prior written permissionPin
of NEDAP.
1 = + buzzerDRAWING:
(red)
No function (2)
X2 PCB
Alarm (Yellow)
SW
ARTICLE NUMBER
A4 CHCK: ?? 2009-MM-DD
FORMAT: REV.
K3
N/A
K3
± 0.2(Not included)± 1°
ISO A(Not included)
K3 (Not included)
AB
AARTICLE ANUMBER
REV.
Pin 1 = Gnd
PinDESCRIPTION
1 =4092201-rs
Gnd
Pin 1 = GndN/A
10.01 OF 1
Pin
+33Volt
in
SHEET:
10.01
OF
1 N/A
Pin
2 = in
+33Volt in
Pin
2 part
= +33Volt
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP.
No
of this
4092201-rs
YYYY-MM-DD
Documentation released
8017328
Circuit diagram
External
Ωswitchbox
(1)
50
ON
D OFF
K2
Ke
Keyswitch
Customer
NC
K102
counting
NC
Sync out
K101
Sync in
K101
Sync in
DSGN:
DIM. IN MM
K101
Sync in
2009-10-26
CB
K102
Sync out
K209K211
GENERAL TOLERANCES K208
K1 ROUGHNESS ACC.
SCALE:
CB buzzer
2009-10-26
1:1 DRW:Deact.
Keyswitch
LIN. config port
ANG. Customer
USB (mini)
ISO 1302 in µM
Antenna
counting
FORMAT:
2009-12-18
CHCK: CB
K209 A3K209
± 0.2
± 1°
(TX-out) N/A K210 K210 ISO A
K210
K209
Deact. buzzer
DESCRIPTION
Deact.
buzzerDeact.
ARTICLE NUMBER
REV.
USB (mini)
config config
port port
USB (mini)
DIM. IN MM
GROENLO HOLLAND
buzzer
2009-10-26
USB (mini) config port
K210
DSG
5276659
QUICK REFERENCE
X2ACC.
ROUGHNESS
GENERAL TOLERANCES
SCALE:
1:1 DRW
LIN. DIM. IN MM ANG. DSGN: CB
ISO 1302 in µM
2009-10-2
GROENLO HOLLAND
DSGN:
SHEET:
DIM.
MM DIM.
GROENLO
HOLLAND
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
45.01HOLLAND
OF 2INFORMAT:
IN MM C
Power on (Green)
GROENLO
C A3
CHCK
FORMAT: A3 CHCK: SW3
drawing may be reproduced
or distributed
in any formN/A
or by any means,
or stored
±
0.2
±
1°
2009-12-18
CB
GENERAL
TOLERANCES
ISO
ROUGHNESS
ACC.
N/A
±
0.2
±
1°
ISO A
SCALE:
2009-10-2
1:1
DRW: CB
GENERAL
TOLERANCES
GENERAL
TOLERANCES
in a data base or retrieval system
without theACC.
prior written
permission ACC.
of
NEDAP.
K101
ROUGHNESS
ROUGHNESS
DRAWING:
T5276-659
K102
SCALE:
LIN.
SCALE:
ANG.
1:1C
1:1 DRW:
ISO 1302 in µM DESCRIPTION
Master/slaveREV.
switch
ARTICLE
DESCRIPTION
LIN.
ANG.
ARTICLE
NUMBER
LIN.
ISOin
1302 in µM
ANG.
ISO 1302 in µM
Sync
Sync
outCB
FORMAT:
2009-12-1
A3
CHCK:
1 A
SW34
CC 1 (Yellow)
N/A 6
± 0.2
± 1°
ISO A
FORMAT:
SW3
N/A
±
± 1° A3FORMAT:
CHCK: A3C
SW3
N/A
± 0.2ISO A
± 0.2
1°
ISO A
Master/slave switch
DESCRIPTION
ARTICLE NUMBER
REV.
CC 2 (Yellow)
DESCRIPTION
Master/slave switch Master/slave switch DESCRIPTION
ARTICLE
NUMB
SHEET:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
SHEET:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
45.01 OF 2
drawing may be reproduced or distributed in any form or by any means, or stored
drawing may be reproduced or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission of NEDAP.
in a data base or retrieval system without the prior written permission
DRAWING:
SHEET:
T5276-659
K1of NEDAP.
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
45.01DRAWIN
OF 2S
Copyright (c)
by N.V.
Apparatenfabriek
NEDAP. No part of this
drawing may be reproduced or distributed
in any
formNederlandsche
or by any means,
or stored
6 distributed
Antenna
drawing
reproduced
or
in any
or by
or SHEET:
stored
Copyright
(c) by 5system
N.V. Nederlandsche
Apparatenfabriek
NEDAP.
No form
part of
thisany means,
in a data
base or retrieval
withoutmay
the be
prior
written permission
of NEDAP.
DRAWING:
T5276-659
in
data
base
or
retrieval
system
without
the
prior
written
permission
of
NEDAP.
drawing
may
be
reproduced
or
distributed
in
any
form
or
by
any
means,
or
stored
(TX-out)
K210
K209
6 without the prior written permission
5 in a data base or retrieval system
of NEDAP.
DRAWING:
Deact.
buzzer
USB (mini) config4 port
GENERAL TOLERANCES
LIN.
ANG.
ROUGHNESS ACC.
ISO 1302 in µM
W3
aster/slave switch
SCALE:
1:1
DRW:
CB
2009-10-26
5276659
QUICK REFERENCE X2
QUICK REFERENCE X2
QUICK REFERENCE
X2 REFERENCE X25276659
QUICK
GROENLO HOLLAND
GENERAL TOLERANCES
LIN.
ANG.
ROUGHNESS ACC.
ISO 1302 in µM
SW3
Master/slave switch
3.2 LED overview
N/A
± 0.2
ISO A
± 1°
SCALE:
FORMAT:
CB
2009-10-26
1:1
DRW:
CB
2009-10-26
A3
CHCK:
CB
2009-12-18
ARTICLE NUMBER
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
drawing may be reproduced or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission of NEDAP.
REV.
5276659
QUICK REFERENCE X2
DSGN:
DIM. IN MM
DESCRIPTION
50 Ω (1)
ON
OFF
527
527665
QUICK REFERENCE X2
Documentation released
DSGN:
DIM. IN MM
DESCRIPTION
YYYY-MM-DD
GROENLO DATE
HOLLAND
REV.
Ref.Nr.
Documentation released
DESCRIPTION
Art.No: 7706707
drawing may
or distributed in any form or by any means, or stored
+3V3 without the+3V3
DRAWING:
in a data base or retrieval
system
prior written permission +3V3
of NEDAP.
(Not included)
N/Abe reproduced
+3V3
DRAWING:
in a data base or retrieval
system withoutREV.
the prior written permission
of NEDAP.
N/A
R474
SW
Ref.Nr.
DATEApparatenfabriek
DESCRIPTION
APPROVED
SHEET:
10.01 OF 1
SW
R474
Copyright (c) by N.V. Nederlandsche
NEDAP. No part of this
SW
R474
IN KSW
1 2
3IN KSW
drawing may be reproduced
distributed in any3form or by any means, or stored4
100 Ω
IN KSW
F 1 2
2 K3 (Notorincluded)
2009-MM-DD
K3 (NotHOLLAND
DSGN: ??
100 Ω
DIM. IN MM
(YELLOW) DRAWING:
+ 12Vthe
forprior
sensors
in a data base or retrieval system without
written
permission
ofincluded)
NEDAP.
GROENLO
Keyswitch
K208
1 Keyswitch
(YELLOW)
+ sensors
12V for sensors N/A
10K Ω
+ 100
12VΩ1 for sensorsK208 10K Ω (YELLOW)
(YELLOW)
+ 12V
for
PinB1 = Gnd
Keyswitch
PinTOLERANCES
1 = Gnd
CC sensor
3 (BLUE)
2 2 GENERAL
ROUGHNESS ACC.
SCALE: 2 4
?? (BLUE)
2009-MM-DD
CC2sensor
DRW: (BLUE)
Pin 2 = +33Volt
in1
GND
CC sensor 2
(BLUE)
CC
sensor
Pin 2 = +33Volt
in
CC
sensor
(RED)
ANG.
LIN.
GND 4
ISO 1302 in µM A
YYYY-MM-DD
Documentation released
GND
NC (RED)
CC1sensor
CC sensor
SW
R474 1
CC(GREEN)
sensor
Gnd
3 DATE
FORMAT:
(RED)
??
2009-MM-DD
R474 (RED)
CHCK:
Ref.Nr. SW REV.
DESCRIPTION
APPROVED
N/A
NC
GND
± 1° Gnd
± 0.2
ISO A
NC
IN KSW
IN KSW
Gnd 100 Ω
(GREEN)
(GREEN)
GND
YYYY-MM-DD
Ω
100
DSGN: ?? NC
DIM. IN MM
GROENLO
HOLLAND
(GREEN)
Circuit
diagramKeyswitch
+ 12V forGnd
sensors
REV.
DESCRIPTIONE
NUMBER
GND
(YELLOW)
+ (YELLOW)
12V forARTICLE
sensors
Keyswitch
GENERAL TOLERANCES
Circuit diagram ROUGHNESS ACC.
CC
sensor
(BLUE)
SCALE:
??
YYYY-MM-DD
1:2
DRW:
CC
sensor
K206
(BLUE)
Circuit diagram
LIN.
ANG.
ISO 1302 in µM
GND
GND
CC sensor
(RED)
Pin
buzzer
(black)
FORMAT:
CC
sensor
YYYY-MM-DD
??
A3
CHCK:
K206
(RED)
N/A
± 0.2
± 1°
K206
ISO A
50 Ω (1)
K206 Gnd
Pin 1 = + buzzer
Gnd (red)
DESCRIPTION
SHEET: (black)
2(GREEN)
= - buzzer
ARTICLECopyright
NUMBER
(GREEN)
ON
(c)REV.
by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this Pin
Pin 2GND
= - buzzer
(black)
GND
7 or
50
Pin
2 stored
= -Pin
buzzer
E Ω (1)2
A or distributed in any form or by any means,
drawing
may be reproduced
OFF
1 = +(black)
buzzer 8(red)
Circuit diagram No function (2) Pin 1 = + buzzer (red)
B5
REV.
4092201-rs
DRW:
CHCK:
2x M4x10
DSGN:
ARTICLE NUMBER
K3 (Not included) K208 A
8017336
10K Ω
10K Ω
K208
K208
10K Ω
Pin 1 = Gnd2External
X2 PCB
(c) by N.V.
Apparatenfabriek
NEDAP. No part of this
External
X2 PCB
5 Nederlandsche
Pin 2 = +33Volt
in Copyright
switchbox
drawing may be reproduced orswitchbox
distributed in any form or by any means, or stored
2x M3x6
1:1
A4
tenna
X-out)
2x M3x10
APPROVED
Ref.Nr.
GROENLO HOLLAND
X2 PCB
+3V3
1 N/A
C4
DESCRIPTION
DESCRIPTION
switchboxX2 PCB
External
switchbox
Cable 2 FR + MD
Ref.Nr.
01
Buzzer with cable
Unit X2
45.01 OF 2
SHEET:
DRAWING:
T5276-659
No function(2)
Alarm(Yellow)
Datacom error(Red)
Power on(Green)
CC 1(Yellow)
CC 2(Yellow)
-9-
Ref.Nr.
REV.
ROUGHNESS ACC.
4. Unit address
The X2 PCB has one network address. Be sure the correct Functionality Modules are installed
5. Connection to PC / Laptop
The X2 uses a min-usb connector for a direct connection with the Configuration Manager.
- 10 -
6. Configuration Manager
All real-time data displayed in the configuration manager, is a subset from the real data. The data communication is not
showing all data, to limit the load on the data bus.
6.1 PL TAB
Below there are 4 real-time parameters, Alarm (red colored), Pulse Count, Sinus / Gauss and internal label detected
counter. The alarm is indicating that the two blue markers are simultaneous in the green area, when the label is gone this
alarm will immediately dim. The lamp on the antenna will be triggered by this signal but has a hold function. The channel and
corresponding frequency will always give a predicted value of the center frequency of the label. When there is no label, it will
predict it in the noise. This results in random changes.
The counter is an internal counter and independent from the counter used for easi/net. The counter has a reset button ‘clear’.
During switching on the unit, the FPGA on board has to be booted. The FPGA status tells if this process succeeded.
A View Spectrum button will open another window with a real-time plot of the spectrum.
The button Save & Close saves all the control parameters into a flash and closes this window. During next boot, the new
written control parameters will be loaded.
6.2 PL RX TAB
This is the main window that gives a quick overview of the
system dynamics. There are two displays showing information of the
actual Q and number of valids. In this display is a green
colored range. This gives the threshold of the receiver for
generating alarm. When both blue markers are simultaneous in
the green area an alarm will be generated. The zoom control is
centered at the max. value of the Q-factor and the min. value of
the Valids.
The control SNR is automated in case Automatic Sensitivity
Control (ASC) is allways activated. During booting of the unit, the
environment of the antenna must be clean from labels.
Start control is default set to a safe value (-3.2dB). This must be
save for almost all situations. When the installation of all units
is done and stable, you can test if the performance is ok. The
performance can be tweaked to its highest level by changing the Start
control to a lower loss value. The dB scale is indicating the expected
sensitivity performance compared to the perfect situation with a
label of Q=80. In situations of using labels with very low Q, it is
giving the most boost. High Q labels benefit not so much from changing this control.
6.3 PL TX TAB
The transmitter can be switched on/off with TX On.
Temperature is monitored and the TX RF power is reduced or switched off when the temperature is above normal.
To prevent label from deactivating, a power control can be used. This control will reduce the RF power at the antenna when
a label enters in its possible deactivation level. The Power meter indicates the actual power of the RF power amplifier, where
128 is max. power and 0 is min. power.
- 11 -
6.4 PL Sync TAB
When the unit is combined with other units, it needs to be
synchronized. This can be switched on/off with unit synchronization (sync). With unit sync activated, the timing of all the units
will be such that the have no/minimum interference from each
other. The sync offset must be set depending on the connection
to the NCC. When the unit is connected to the master NCC this
offset is 0. When the unit is connected to the first slave NCC this
offset must be set to 1, the second NCC to 2, third NCC to 3 etc.
There are two sync slots 0 and 1. It is free to select a value. Between
units with a different value one is 0 and the other 1, means they are
100% independent from each other even in an environment with
very strong coupling between antennas at large distances.
Remark: When unit sync is active and no sync is connected, the
buzzer and RF signal are switched off to prevent false alarms
in this and other units. When Unit sync is activated but no sync
signal is connected, the RED LED on the unit is on (D101). So
RED LED D101 on? No RF TX signal and alarm are given.
To synchronize the Nedap Retail sweep system with the X2 we
need to set the correct active phase. When a Nedap swept system is synchronized with the X2, all mux settings on the sweep
system must be set on 4. This gives phases A,B,C and D. When the sweep system is active in phase A and B the X2 must be
switched to the other free phases C and D.
This product only supports a sweep system(s) connected to/configured as the master NCC.
In default setting, all phases are switched to active (value 1). If a swept system is configured to work on phase 1, the chameleon
must have that phase inactive so value 0. In general when synchronizing a swept system with the chameleon, the phases must
be inverted from each other.
Synchronization of Nedap sweep systems other then NCC MK2 (P2) are not supported.
- 12 -
6.5 PL Alarm TAB
Alarm Enable is default active. When no lamp and buzzer
signal must be given it must be switched off. Remember that when
switched off, EASi/Net™ will NOT register events.
Buzzer mode: select between off, whine or continuous
Lamps Pulse mode: is the hold time of the lamp after label is not
in the detection field
6.6 ASC
With the ASC Range, the sensitivity can be controlled. If there
is a situation that less sensitive is wanted, the ASC range can be
increased (larger number). To decrease (lower sensitive) the
detection range default ASC=100.
Long term valids and log term Q give an indication in the stability
of the unit in this environment. If both are 0 and stay 0, the unit
function stable.
6.7 Spectrum analyzer
Using View Spectrum will open an extra window with a spectrum analyser. The same window can be selected with the TAB
Spectrum.
- 13 -
This is a real-time spectrum analyser. On the horizontal axe is
frequency (between 7.4MHz and 8.8MHz), and vertical is level
relative given in dB.
The Level can be changed up/down. Scaling can be changed to
zoom in and out. Average can be switched between quicker
response but more noise to slower response but les noise.
At selection View are 3 choices of view types:
• All : show everything
• Gauss: only update plot when normal noise is detected
• Valid: only update plot when normal noise is detected and the
correct signal to noise (SNR)
These 3 types give you the tools to determine what the spectral
environment looks like. Is the environment clean, is there a carrier,
is there a swept system or is there a pulse-listen system.
- 14 -
7. System configuration
The new X2 electronics can be used as an internal in an antenna or external electronics. By use of an power inserter, 6
electronics can be connected.
An NCC MK2 can communicate with up to a maximum of 24 X2 electronics.
Table 1
Number of antennas
1-6
7 - 12
13 - 18
19 - 24
25 - 30
31 - 36
37 - 42
43 - 48
49 - 54
55 - 60
61 - 66
etc.
Non-connected systems
1 power inserter
1 NCC, 1 Power Inserter
1 NCC, 2 Power Inserters
1 NCC, 3 Power Inserters
2 NCC’s, 3 Power Inserter
2 NCC’s, 4 Power Inserters
2 NCC’s, 5 Power Inserters
3 NCC’s, 5 Power Inserters
3 NCC’s, 6 Power Inserters
3 NCC’s, 7 Power Inserters
4 NCC’s, 7 Power Inserters
etc.
Connected systems
1 NCC
same as non-connected, plus modem or LAN
same as non-connected, plus modem or LAN
same as non-connected, plus modem or LAN
same as non-connected, plus modem or LAN
same as non-connected, plus modem or LAN
same as non-connected, plus modem or LAN
same as non-connected, plus modem or LAN
same as non-connected, plus modem or LAN
same as non-connected, plus modem or LAN
same as non-connected, plus modem or LAN
etc.
7.1 Medium scale installation example
When using a 4 output NCC, a maximum of 24 PCB’s can be connected. Below an example of a system with 19 antennas and
48 antennas.
NCC MK2
Power
Inserter
Power
Inserter
Power
Inserter
- 15 -
NCC MK2
Power
Inserter
Power
Inserter
NCC MK2
Power
Inserter
Power
Inserter
Power
Inserter
- 16 -
8. Specifications X2
Frequency 		
Antenna Connections
Synchronization		
Weight			
Temperature range
Power Supply		
: 8.2 MHz
: 1x 50 Ohm BNC Transceiver connector
: 1x input 50 Ohm BNC
1x output 50 Ohm BNC
: 3 kg
: 0°C …+40°C
: 30~33V DC, 400mA
- 17 -
F
X2
Buzzer with cable
Unit X2
01
External
SW
Keyswitch
ExternalACC.
ROUGHNESS
Circuit
diagramKeyswitch
GND
Keyswitch
ROUGHNESS ACC.
ISO 1302 in µM
GND
Circuit diagram
External
(1)
50 Ωswitchbox
ON
D OFF
Alarm (Yellow)
Keyswitch
SHEET:
± 1°
Datacom error (Red)
IN KSW
Ω (1)
ON
OFF
C 50
CC 2 (Yellow)
CC 2 (Yellow)
Alarm (Yellow)
USB (mini) config port
FORMAT:
A3
LIN.
2009-MM-DD
Art.No: 7706707
Art.No:
7706707
Art.No:
7706707
(Not included)
(Not included)
78
Art.No: 7706707
A.01
10.01 OF 1
SHEET:
DRAWING:
K206
(RED)1
CC sensor
K206
K3 (Not included)
Pin 1 = Gnd
Pin 2 = +33Volt in
K208
Customer
counting
NC
NC
(RED)
K211
Keyswitch
NC
NC
K206
Pin 2 = - buzzer (black)
Pin 1 = + buzzer (red)
K101
Sync in
K209
Deact. buzzer
K102
Sync out
K210
USB (mini) config port
K211
Keyswitch
K211
Keyswitch
GROENLO HOLLAND
K211
Keyswitch
K101
Sync in
K101
Sync in
K101
Sync in
K102
Sync out
K210
K209K211
K208
GENERAL TOLERANCES
K1 ROUGHNESS ACC.
SCALE: 1:1
CB buzzer
2009-10-26
DRW:
Deact.
Keyswitch
LIN.
USB (mini)
configANG.
portCustomer
ISO 1302 in µM
Antenna
counting
FORMAT:
2009-12-18
CB
A3
CHCK:
K210
K209
K209
± 0.2
± 1°
ISO A
(TX-out) N/A K210
K210
K209
Deact. buzzer
DESCRIPTION
Deact.
ARTICLE buzzer
NUMBER REV.
(mini)(mini)
config config
port port
DIM. IN MM
GROENLO
HOLLAND
Deact. buzzer
2009-10-26 USB USB
USB (mini) config port
5276659
QUICK REFERENCE
X2
ROUGHNESS ACC.
K102
Sync ou
K102
Sync out
K10
Syn
2009-10-26
DSGN: CB
DIM. IN MM
K208
K208 Customer
counting
Customer
(YELLOW)
K211
counting K208
(BLUE) K208
Keyswitch
(RED) Customer
Customer
NC
counting
K102
counting
(GREEN)
NC
Sync out
+ 12V for sensors
CC sensor 2
CC sensor 1
K101
Gnd
Sync in
K1
Antenna
(TX-out)
N/A
K206
K206
Pin 2 = - buzzer 3(black) Pin 2 = - buzzer
(black)
Art.No: 7706707
included)
Pin 1 = + buzzer (red) Pin 1 = + (Not
buzzer
(red)
N/A
K1
Antenna
(Not include
APPROVED
Gnd
2(GREEN)
= - SHEET:
buzzer (black)10.01
(GREEN)
OF 1
(c)REV.
by N.V. Nederlandsche Apparatenfabriek NEDAP. No part Pin
ofGnd
this
7 2=
Pin
-stored
buzzer
(black)
drawing
may be reproduced
or distributed
in any form or by any means,
orPin
1 = + buzzer
(red)
in a data base or retrieval system without the prior written permission
of =
NEDAP.
N/A
Pin 1
+ buzzerDRAWING:
(red)
N/A
Art.No: 7
(Not included)
N/A
SHEET:
2009-MM-DD
(YELLOW)
+ 12V
for sensors (YELLOW)
12V for
sensors
Pin 1 =+Gnd
Pin 1 = + buzzer (red)
APPROVED
??
?? 62009-MM-DD
(Not included)
ARTICLE NUMBER
A4
FORMAT: REV.
4092201-rs
CC sensor
Pin 2 = - buzzer
(black)1
CHCK: ?? YYYY-MM-DD
ARTICLE
NUMBER
Copyright
SW3
Master/slave switch
Datacom error (Red)
DSGN: CB
GROENLO HOLLAND DIM. IN MM
2009-MM-DD
ANG.
Pin 1 = Gnd
Power on (Green)
K209
Deact. buzzer
K210
± 1°
K211
Keyswitch
K1
K1
Antenna
Antenna
(TX-out)
(TX-out)
??
GENERAL TOLERANCES SCALE:
DSGN:
DRW: ??
DIM. 2009-MM-DD
IN MM
GROENLO 1:1
HOLLAND
ANG.
LIN.
GENERAL
TOLERANCES
A45 CHCK:
FORMAT:
??
2009-MM-DD
SCALE:
1:1 DRW:
ROUGHNESS
± 0.2
ISO A 4ACC. 5
ISO 1302 in µM
CC 2 (Yellow)
APPROVED
10.01 OF 1
K3
K3 (Notofincluded)
DSGN: ??
DIM. IN MM
(YELLOW)
DRAWING:
+ 12Vthefor
in a data base or retrieval system without
priorsensors
written
permission
NEDAP.
GROENLO
HOLLAND
N/A
CC 1(TX-out)
(Yellow)
CC 2 (Yellow)
drawing may
or distributed in any form or by any means, or stored
N/Abe reproduced
DRAWING:
in a data base or retrieval
system without
the prior written
permission of NEDAP.
Ref.Nr.
REV.
DATE
DESCRIPTION
Copyright (c) by
N.V. Nederlandsche
Apparatenfabriek
NEDAP. No part of this
drawing may be reproduced
or distributed in any3form or by any means, or stored4
(Not included)
Power
on (Green)
Datacom error
(Red)
Datacom error (Red)
CC 1(2)(Yellow)
No function
CC 1 (Yellow)
K3
2009-MM-DD
CHCK: ??
N/A
K3
± 0.2(Not included)± 1°
ISO A(Not included)
K3 (Not included)
N/A
AARTICLE ANUMBER
REV.
DESCRIPTION
Pin 1 = Gnd
Pin
1 =4092201-rs
Gnd
Pin 1 = Gnd
10.01 OF 1
APin
2 = +33Volt
in Pin
Pin
2 = SHEET:
+33Volt
in10.01 OF 1 N/A
2 =No +33Volt
in
Copyright (c) by N.V.
Nederlandsche
Apparatenfabriek
NEDAP.
part
of this
4092201-rs
YYYY-MM-DD
Documentation released
AB
K101
Power on (Green)
Sync
in
CC
1(Green)
(Yellow)
Power
on
YYYY-MM-DD
Documentation released
DSGN:
DIM. IN MM
GROENLO
HOLLAND
REV.
DATE
DESCRIPTION
Datacom error (Red)
CC 1 (Yellow)
Circuit diagram
Documentation released
DESCRIPTION
Datacom error (Red)
Power on (Green)
GND
Alarm (Yellow)
2x M4x10
CC sensor
3 (BLUE)
TOLERANCES
ROUGHNESS1 ACC.
?? (BLUE)
2009-MM-DD
CC
sensor
21:1
DRW:(BLUE)
Pin 2 = CC
+33Volt
in 1GENERAL
sensor
Pin 2 =CC
+33Volt
in SCALE:
sensor
(RED)
ANG.
LIN.
ISO 1302 in µMNC (RED)
CC FORMAT:
sensor
1A4
CC
sensor
Gnd
(GREEN)
?? NC2009-MM-DD
CHCK: (RED)
± 1° Gnd
± 0.2
ISO A
NCN/AAPPROVED
IN KSW
(GREEN)
YYYY-MM-DD
DSGN: ?? NC
DIM. IN MM
(GREEN)
+ 12V forGnd
sensors
REV.
DESCRIPTION
NUMBER (YELLOW)
+ (YELLOW)
12V forARTICLE
sensors
CC
sensor
(BLUE)
SCALE: 1:2
??
YYYY-MM-DD
DRW:
CC
sensor
K206
(BLUE)
K208
Customer
counting
R474
CC 2 (Yellow)
DSGN:
CB
2009-10-
GENERAL TOLERANCES SCALE:
1:1 DRW: CB 2009-10LIN.DIM. IN MMANG. DSGN: CB
2009-10-26
GROENLO HOLLAND
2009-10-26
DSGN:
SHEET:HOLLAND
MM DIM.
GROENLO
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
2009
CB
45.01 DIM.
OF IN
2FORMAT:
IN MM CBDSGN:
GROENLO
HOLLAND
C A3
2009-12CHCK: CB
N/Aor by anyGENERAL
drawing may be reproduced
or distributed
means, orISO
stored
± 0.2SCALE: 1:1
± 1° DRW:
2009-12-18
CB
TOLERANCES
CHCK:SW3
ROUGHNESS
ACC. in any form
N/A
CB
2009-10-26
GENERAL
TOLERANCES
GENERAL
TOLERANCES
in a data base or retrieval system
without the prior
permission
of NEDAP.
K101
ROUGHNESS
ACC.
ROUGHNESS
ACC.written
DRAWING:
T5276-659
K102
SCALE:
CB REV.
2009
LIN.
SCALE:
ANG.
1:1CBNUMBER
DRW:2009-10-26
1:1
DRW:
ISO
1302
in
µM
Master/slave
switch
DESCRIPTION
ARTICLE
DESCRIPTION
LIN.
ANG.
ARTICLE
NUMBER
REV.
LIN.
ISO
1302
in
µM
ANG.
ISO
1302
in
µM
Sync
in
Sync
out
FORMAT:8A3 CHCK: CB
2009-12-18
1 A
SW34
CC 1 (Yellow)
N/A 6
± 0.27
± 1°
ISO A
200
CB
A3CBCHCK:
FORMAT:
SW3
N/A
2009-12-18
±± 0.2
± 1° A3FORMAT:
CHCK:
ISO A
SW3
N/A
±
0.2
1°
ISO
Master/slave switch
DESCRIPTION
ARTICLE NUMBER REV.
CC 2 (Yellow)
DESCRIPTION
ARTICLE NUMBER R
Master/slave switch Master/slave switch DESCRIPTION
ARTICLE
NUMBER
REV.
A 45.01
SHEET:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
OF
SHEET:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
45.01 OF 2
drawing may be reproduced or distributed in any form or by any means, or stored
drawing may be reproduced or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission of NEDAP.
T5276-65
in a data base or retrieval system without the prior written permission
DRAWING:
SHEET:
T5276-659
K1 of NEDAP.
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
45.01DRAWING:
OFSHEET:
Apparatenfabriek
NEDAP. No part of this
45.01
drawing may be reproduced orCopyright
distributed(c)inby
anyN.V.
formNederlandsche
or by any means,
or stored
6or distributed
7means,SHEET:
Antenna
drawing
maythe
beprior
reproduced
in any form
or
byofany
or
stored
Copyright
(c) by5 system
N.V.
Nederlandsche
Apparatenfabriek
NEDAP.
No part
this
45.018 OF 2
in a data
base or retrieval
without
written permission
of
NEDAP.
DRAWING:
T5276-659
in K209
a dataor
base
or retrieval
without
prior
writtenor
permission
drawing may be reproduced
distributed
in system
any form
or bythe
any
means,
stored of NEDAP.
DRAWING:
(TX-out)
T527
K210
5 in a data base or retrieval system
without the prior written 7permission of NEDAP.
DRAWING:
T5276-659
Deact.
buzzer
4 port
USB (mini) config
ROUGHNESS ACC.
ISO 1302 in µM
SW3
Master/slave switch
N/A A
GENERAL TOLERANCES
LIN.
ANG.
± 0.2
Ref.Nr.
REV.
ARTICLE NUMBER
DESCRIPTION
100Ω
GND
2009-MM-DD
ROUGHNESS ACC.
7706707
ISOArt.No:
1302 in µM
2009-MM-DD
(NotN/A
included)
3 4
No function (2)
10KΩ
2D
Alarm (Yellow)
DRW: ??
CHCK: ??
in a data base or retrieval system without the prior written permission of NEDAP.
Ω (1) +3V3
50+3V3
ON
No function (2)
OFF
Alarm (Yellow)
SW
K1
Antenna
(TX-out)
GND
ISO A
YYYY-MM-DD
DATE
2009-MM-DD
No function
drawing may(2)
be reproduced or distributed in any form or by any means, or stored
X2 PCB
K208
Alarm (Yellow)
3 ± 1°
2x M3x6
B5
DSGN: ??
-3buzzer (black) GND 4
2No function (2)
50
E Ω (1)
Pin 1 = + buzzer8017328
(red)
50 Ω (1) Circuit diagram
Circuit diagram
ON
No
function
(2)
ON
OFF
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
OFF
DIM. IN MM
DESCRIPTION
Pin GND
2=
REV.
APPROVED
Ref.Nr.
GENERAL TOLERANCES SCALE: 1:1
ANG.
+3V3FORMAT: A4
N/A
K206
50 Ω (1)
ON
OFF
CC sensor 2
(BLUE)
GND 4
YYYY-MM-DD
Documentation released
GND
CC sensor
1A
R474
3 DATE
R474(RED)
Ref.Nr. SW REV.
DESCRIPTION
GND
IN KSW
Gnd 100Ω
(GREEN)
GND
100Ω
GROENLO HOLLAND
GND
Circuit diagram
X2 PCB
DESCRIPTION
GROENLO HOLLAND
X2 PCB
SW
3Documentation released
+3V3
DRAWING:
in a data base or4retrieval+3V3
system without the
prior written permission
of NEDAP. +3V3
+3V3
R474
SW
R474
R474
IN KSW
1 2
3IN KSW
100Ω
IN KSW
100Ω
100Ω1
K208
10KΩ
1 Keyswitch
K208
10KΩ
(YELLOW)
+ 12V for sensors
Keyswitch
YYYY-MM-DD
DATE
K3 (Not included) K208 A
8017336
10KΩ
K208
10KΩ
K208
10KΩ
Pin 1 = Gnd
2External
X2 PCB
(c) by5N.V. Nederlandsche
ExternalApparatenfabriek
X2 PCBNEDAP. No part of this
Pin 2 = +33Volt
in Copyright
switchbox
drawing may be reproduced or
distributed in any form or by any means, or stored
switchbox
SW
REV.
DESCRIPTION
Ref.Nr.
switchboxX2 PCB
External
LIN.
switchbox
ISO 1302
in µM +3V3
+3V3+3V3
switchbox
+3V3
+3V3ISO A
± 0.2 2
1 N/A
F F
2x M3x10
Cable 2 FR + MD
GENERAL TOLERANCES SCALE:
1:1
LIN.
ANG.
Power on (Green)
FORMAT: A3
± 0.2
± 1°
ISO A
5276659
QUICK REFERENCE X2
DRW: CB
2009-10-26
ISO 1302 in µM
QUICK REFERENCE X2
QUICK REFERENCE
5276659
QUICKX2REFERENCE
X2
5276659
QUICK REFERENCE X2
GROENLO HOLLAND
ROUGHNESS ACC.
ISO 1302 in µM
SW3
Master/slave switch
N/A
ISO A
DESCRIPTION
GENERAL TOLERANCES SCALE:
1:1
LIN.
ANG.
FORMAT: A3
± 0.2
± 1°
description:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
drawing may be reproduced or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission of NEDAP.
QUICK REFERENCE X2 | art no. 8017328
DRW:
CB
2009-10-26
CHCK:
CB
2009-12-18
chk:
REV.
5276659
QUICK REFERENCE X2
2009-10-26
drw: CB 2011/03/09
CB
DSGN:
DIM. IN MM
ARTICLE NUMBER
GROENLO - HOLLAND
5276659
c 5276659
45.01 OF 2
SHEET:
DRAWING:
T5276-659
doc. article no: 5276659
rev. : D
Copyright © by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this drawing sheet: 45.01 of 1
may be reproduced or distributed in any form or by any means, or stored in a data base or
drawing: T5276-659
retrieval system without the prior written permission of NEDAP.
Ref.Nr.
- 18 -
REV.
YYYY-MM-DD
DATE
ROUGHNESS ACC.
ISO 1302 in µM
N/A
DESCRIPTION
ISO A
- 19 -
BACK Manual X2 2012
parallelweg 2d
- 20 7141 dc groenlo
the netherlands
t +31 (0) 544 47 15 55
www.nedapretail.com
e info-rs@nedap.com
f +31 (0) 544 46 58 14
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Tagged PDF                      : Yes
Page Count                      : 20
Create Date                     : 2012:02:13 16:01:45+01:00
Creator                         : Adobe InDesign CS5 (7.0)
Modify Date                     : 2012:02:13 16:02:07+01:00
Producer                        : Adobe PDF Library 9.9
Trapped                         : False
EXIF Metadata provided by EXIF.tools
FCC ID Filing: CGDX2

Navigation menu