New Centurion Solutions NCS03010910 HANDHELD SECURITY DEVICE User Manual Project 623
New Centurion Solutions, Inc. HANDHELD SECURITY DEVICE Project 623
Contents
- 1. Users Manual
- 2. Installation Manual
Installation Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1450752 |
| Application ID | xolZ5yM6TqpN5CYj/cGfYQ== |
| Document Description | Installation Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 65.69kB (821182 bits) |
| Date Submitted | 2011-04-19 00:00:00 |
| Date Available | 2011-04-19 00:00:00 |
| Creation Date | 2011-03-16 11:59:01 |
| Producing Software | Microsoft® Office Word 2007 |
| Document Lastmod | 2011-03-16 11:59:01 |
| Document Title | Project 623 |
| Document Creator | Microsoft® Office Word 2007 |
| Document Author: | Scott Elliott |
Elliott Tech, LLC IREP Installation Manual IREP New Centurion Solutions Project Number: 776 Reference: 776-91-06-REV-IREP_INSTALLATION_MANUAL.docx Original Document: March 1, 2011 Revision A: March 16, 2011 Prepared for: New Centurion Solutions, Inc. Greg Williams 3011 Spring Garden St. Suite E Greensboro, NC 27403 (336) 617-5410 GWilliams@newcenturionsolutions.com Prepared by: Elliott Tech, LLC 346 Raleigh Street Holly Springs, NC 27540 (919) 342-6899 (888) 631-1795 Fax s.elliott@elliotttech.com THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO NEW CENTURION SOLUTIONS, INC. AND SHALL NOT BE REPRODUCED OR DISCLOSED IN WHOLE OR IN PART FOR ANY DESIGN OR MANUFACTURE EXCEPT WHEN SUCH USER POSSESSES DIRECT, WRITTEN AUTHORIZATION FROM NEW CENTURION SOLUTIONS, INC. IREP Installation Manual 776-91-06-REV-A_IREP_INSTALLATION_MANUAL.docx Revision Page Rev Description FCC Notification Section THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO NEW CENTURION SOLUTIONS, INC. AND SHALL NOT BE REPRODUCED OR DISCLOSED IN WHOLE OR IN PART FOR ANY DESIGN OR MANUFACTURE EXCEPT WHEN SUCH USER POSSESSES DIRECT, WRITTEN AUTHORIZATION FROM NEW CENTURION SOLUTIONS, INC. ii IREP Installation Manual 776-91-06-REV-A_IREP_INSTALLATION_MANUAL.docx Contents 1. Equipment List ......................................................................................................... 4 2. Installation Prerequisties ........................................................................................ 5 3. Installation Instructions .......................................................................................... 5 4. FCC Notification ...................................................................................................... 6 THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO NEW CENTURION SOLUTIONS, INC. AND SHALL NOT BE REPRODUCED OR DISCLOSED IN WHOLE OR IN PART FOR ANY DESIGN OR MANUFACTURE EXCEPT WHEN SUCH USER POSSESSES DIRECT, WRITTEN AUTHORIZATION FROM NEW CENTURION SOLUTIONS, INC. iii IREP Installation Manual 1. 776-91-06-REV-A_IREP_INSTALLATION_MANUAL.docx EQUIPMENT LIST A. Antenna, helical short ¼ wave (1) B. IREP Assembly (1) C. Double-gang box installation (pre-requisite) D. #6-32 pan head screw (4) – included with IREP assembly E. #6-32 x 1” button-head screw (1) – included with IREP assembly THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO NEW CENTURION SOLUTIONS, INC. AND SHALL NOT BE REPRODUCED OR DISCLOSED IN WHOLE OR IN PART FOR ANY DESIGN OR MANUFACTURE EXCEPT WHEN SUCH USER POSSESSES DIRECT, WRITTEN AUTHORIZATION FROM NEW CENTURION SOLUTIONS, INC. IREP Installation Manual 2. 776-91-06-REV-A_IREP_INSTALLATION_MANUAL.docx INSTALLATION PREREQUISTIES Ensure that the following installation prerequisite is met: 3. Wiring and installation of double-gang box INSTALLATION INSTRUCTIONS To begin, check the parts available against the equipment list, identifying any missing parts. If all parts are accounted for, proceed to the instructions below to begin installing the IREP. Step 1 Step 1: Identify the Antenna, helical short ¼ wave (A). Screw the antenna into the gold coaxial antenna connector on the top of the IREP assembly (B). Ensure that the antenna is screwed onto the connector snugly, but take care not to over-tighten the antenna as it will damage the connector or the IREP assembly enclosure. Step 2: Identify the power supply wires located within the double-gang installation. Ensure that the positive and negative wires are identified before proceeding with the installation. Identify the green and orange terminal block on the IREP Printed Circuit Board (PCB). Note the “+” silkscreen market on the PCB just to the Step 2 lower right of the terminal block. Connect the positive power supply wire to the terminal block connection distinguished by the “+” marker, and connect the negative power supply wire to the opposite terminal block connection. The green LED on the front of the IREP enclosure should illuminate when power is correctly connected. (-) (+) THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO NEW CENTURION SOLUTIONS, INC. AND SHALL NOT BE REPRODUCED OR DISCLOSED IN WHOLE OR IN PART FOR ANY DESIGN OR MANUFACTURE EXCEPT WHEN SUCH USER POSSESSES DIRECT, WRITTEN AUTHORIZATION FROM NEW CENTURION SOLUTIONS, INC. IREP Installation Manual 776-91-06-REV-A_IREP_INSTALLATION_MANUAL.docx Step 3: Identify the #6-32 pan head screw (D). Ensure that the outer half of the enclosure is detached from the inner half. Secure the inner half of the IREP (connected to wires) assembly to the double-gang box with four of these screws. Step 3 Step 4: Identify the outer half of the IREP enclosure. Secure this half over the first half using the #6-32 x 1” button-head screw (E) at the top center of the IREP. Step 4 4. FCC NOTIFICATION NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO NEW CENTURION SOLUTIONS, INC. AND SHALL NOT BE REPRODUCED OR DISCLOSED IN WHOLE OR IN PART FOR ANY DESIGN OR MANUFACTURE EXCEPT WHEN SUCH USER POSSESSES DIRECT, WRITTEN AUTHORIZATION FROM NEW CENTURION SOLUTIONS, INC.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 6 Language : en-US Tagged PDF : Yes Title : Project 623 Author : Scott Elliott Subject : 623_SRS_Acroprint Creator : Microsoft® Office Word 2007 Create Date : 2011:03:16 11:59:01 Modify Date : 2011:03:16 11:59:01 Producer : Microsoft® Office Word 2007EXIF Metadata provided by EXIF.tools