Nokia Solutions and Networks CPE25300 Non-line of Sight Wireless Data Link User Manual 285a66

Nokia Solutions and Networks Non-line of Sight Wireless Data Link 285a66

UserManual.wiki >

Nokia Solutions and Networks >

CPE25300 User Manual >

Contents

Manual

-1ContentsContentsDesktop CPEi 300 User GuideOverview. . . . . . . . . . . . . 1Powerful Features in a Single Unit . . . . . . . . . . . 3Front of CPE . . . . . . . . . . 3Back of CPE . . . . . . . . . . 6Operating Information. . . 7Overview. . . . . . . . . . . . . 7Before You Begin . . . . . . 7Easy Setup. . . . . . . . . . . . 9Advanced Setup . . . . . . 10Before you Begin Configuration . . . . . . . . 11Logging In to the CPE. . 11Setup Wizard and AuthenticationStep 1 - Change Password 13Step 2 - Device Time. . . 14Step 3 - WiMAX Security 14Step 4 - Account . . . . . . 15Basic ConfigurationPersonalize Menu . . . . . 17Internet Menu . . . . . . . . 21Status Menu. . . . . . . . . . 25Telephony Menu . . . . . . 26

0ContentsAdvanced ConfigurationPort Fowarding Menu. . . 36Local Address Menu . . . 39Control Panel . . . . . . . . . 44Configuring TCP/IPConfiguring TCP/IP in Windows 2000 . . . . . . . . 47Configuring TCP/IP in Windows XP. . . . . . . . . . 51TroubleshootingPower LED is Off. . . . . . 56A Computer Cannot Log On to the CPE . . . . . 56Cannot Connect to the Internet . . . . . . . . . . . 56Additional Troubleshooting Help . . . . . . . . . . . . . . . . 56Important Safety and Legal InformationDisposal of Motorola Equipment in EU Countries . . . . . . . . . 62Disposal of Motorola Networks Equipment in Non-EU countries. . . . . . 63CMM DisclosureCopyrights and TrademarksNotice . . . . . . . . . . . . . . . 66Copyrights . . . . . . . . . . . 66Usage and Disclosure Restrictions. . . . . . . . . . . 67Trademarks. . . . . . . . . . . 68

1Desktop CPEi 300 User GuideDesktop CPEi 300 User GuideOverviewThank you for purchasing the Motorola CPE Indoor (CPEi) 300 desktop device. The Desktop CPEi allows you to connect to the wireless world easily and seamlessly without complicated installa-tion and setup procedures. In addition it offers you the ability to make Voice over Internet Protocol (VoIP) calls.The Desktop CPE indoor (CPEi) device provides the user:•Convenience — with easy plug and play functionality. Compact design.•Performance — dual antennas supply diversity technology. Best in Class range and indoor penetration.•Control — remote management capability allows easy detection and authentication once the unit is setup. •VoIP - two RJ11 ports allow for Voice over IP calls using your CPEi 300.

2Desktop CPEi 300 User GuideDesktop CPEi 300The features and the physical appearance of your Desktop CPEi device may differ slightly from the illustration. This product is subject to change. For the most recent documentation, visit the Product Documentation page on www.motorola.com.

3Desktop CPEi 300 User GuidePowerful Features in a Single UnitThe CPE device provides the following features:•WiMAX Authentication•WAN DHCP Client•LAN DHCP Server•Home Gateway FunctionsFront of CPEThe Front of the CPE units contain LED Link/Activity indicators. The LEDs provide the status of the unit and signal strength indicators for easy adjustment during setup.Front of Unit

4Desktop CPEi 300 User GuideLED Indicator InterfacePower Status The Power LED indicator is:•On — power to CPE is on.•Off — power to the CPE is off. Ethernet Status The Ethernet LED indicator is:•On - LAN Ethernet link has been established.•Blinking - LAN Ethernet activity has been detected.•Off - LAN Ethernet link has been dropped.Signal Strength Full WiMAX Signal Strength is detected if all WiMAX Signal Strength LEDs are lit.•All WiMAX Signal Strength LEDs are off - low signal detected.•First WiMAX Signal Strength LED is lit - low signal detected.•First and second WiMAX Signal Strength LED is lit - high signal detected.

5Desktop CPEi 300 User GuideCaution: If the Power LED and all 3 WiMAX Signal Strength LEDs are blinking, then a software upgrade is in progress. Do NOT remove power to the CPE.Note: If the Power LED is BLINKING and all 3 WiMAX Signal Strength LEDs are OFF, the CPE device is overheating, and you will not have service.WAN WiMAX While acquiring access to the WiMAX Network: •The Power LED is ON.•The WAN LED is OFF.•All WiMAX Signal Strength LEDs will be in vary between ON, OFF and/or BLINKING status.Once connectivity to the WiMAX Network is established:•The Power LED is ON.•The WAN LED is ON.When WiMAX traffic is detected:•The Power LED is ON.•The WAN LED is BLINKING.

6Desktop CPEi 300 User GuideBack of CPEThe back of the CPE unit contains the reset switch, AC Power Connector, Ethernet connector, Line 1 and Line 2 telephone ports, and the External Antenna Connector (accessory available from your service provider).Back of the UnitPort DescriptionsBack Panel Ports DescriptionExternal Antenna External Antenna ConnectorEthernet Ethernet PortPower AC Power ConnectorResetNote: Hardware Reset Button (A paperclip is recommended for accessing this button). Before resetting the CPE, ensure the power LED is ON.Phone Line 1 RJ-11 port for use with VoIP.Phone Line 2 RJ-11 port for use with VoIP.

7Desktop CPEi 300 User GuideOperating InformationOperating temperature for this unit is 0-40C (32-104F).InstallationOverviewTo install the Desktop CPEi 300 Series, you need to review the following sections:•Before You Begin•Easy SetupBefore You BeginBefore you begin installation, check that you have received the following items with your Desktop CPEi 300:In the box with your CPE you should have:Item DescriptionAC AdapterPower adapter and cord connects the Desktop CPE to an AC electrical outlet.Ethernet Cable The ethernet cable connects the Internet port on your Desktop CPE to your PC or laptop computer.Desktop CPEi 300 Quick Start GuideProvides quick installation instructions for getting your Desktop CPE up and running.

8Desktop CPEi 300 User GuideIn addition, you will also need:•A computer •An RJ-11 telephone cable (optional). Two RJ-11 telephone cables will be required if your service provider has supplied you with two telephone numbers.

9Desktop CPEi 300 User GuideEasy SetupThe CPE is easily set up in your home. Basic installation equipment needed are the power adapter and cord, Ethernet cable, a PC or lap-top computer and the CPE device. If you want to use the VoIP func-tionality, you will also need an RJ-11 phone cable and a telephone.Perform the following tasks before attaching the power cord or powering up the unit:•Stand the CPE on a flat surface.•Plug the power adapter into the power connector on the back of the unit.•Plug the AC power cord into an AC outlet. The unit will turn on.•Plug one end of the Ethernet cable into the Ethernet connector on the back of the unit.•Plug the other end of the Ethernet cable into the Ethernet connector of your computer.•To use VoIP functionality of the phone, plug one end of the phone line into the activated phone connector on the back of the unit. Phone line activation is dependent upon your service contract.•Plug the other end of the phone line into the phone line connector of your telephone.

10Desktop CPEi 300 User GuideAdvanced SetupThe CPE can also be used to connect to a multi-port switch (hub) - purchased separately from the CPE. Connecting the CPE device to a hub will allow you to connect more than one computer to your CPE device. See the picture below for an example.

11Desktop CPEi 300 User GuideProcedure to Log into the CPEBefore you Begin ConfigurationSome settings on your computer must be verified or changed to ensure that your computer configuration can support the Desktop CPE. Verify that the IP addresses and DNS settings are automatically generated in your Local Area connection of your Internet Protocol (TCP/IP) properties. Refer to the chapter titled “Configuring TCP/IP” for information on how to do this.Logging In to the CPEUse the following procedure to log into the Desktop CPE.1On a computer that is connected to the Desktop CPEi, open a web browser.2In the Address or Location field, type http://mywimax. and press ENTER to display the login screen.Note: You must include the period (.) after http://mywimax. in order to access the login screen.3The Welcome to Motorola WiMAX CPE screen will be displayed and will prompt you for a password.

12Desktop CPEi 300 User GuideLogin Screen4In the Password field, type the password (default is motorola).5Click Login. 6First time users will see a pop-up box that states: “The Wizard application will guide you through for the first time configuration. Click OK button to continue.”7Click the OK button to launch the wizard application.

13Setup Wizard and AuthenticationSetup Wizard and AuthenticationStep 1 - Change PasswordOnce you have launched the setup wizard, you will be prompted to change your password. Motorola recommends using a password to protect your home network and CPE device. Passwords are case-sensitive.To change your password:•Ensure the “Enable Login Password Protection” box is checked.•Enter a New Login Password in the box. Passwords can be no more than 20 characters in length.•Re-type your new password in the Confirm New Login Password box.•Click Next.Note: If you forget your password, you can reset it back to the default (motorola) by pressing and holding the reset button on the back of your CPE for more than 5 seconds. Before resetting the CPE, ensure the power LED is ON.

14Setup Wizard and AuthenticationStep 2 - Device TimeThis screen allows you to set the time zone and to enable Daylight Savings Time (when applicable) for your location. •Select the appropriate time zone for your location from the drop down box.•Check the box called “Auto Adjust for Daylight Savings Time” if you live in a region that observes Daylight Savings Time (this box is checked by default).•Click the Next button.Step 3 - WiMAX SecurityThe WiMAX Security tab will contain your authentication method. Check with your service provider to determine if they require a user name and password for authentication purposes.•If the Authentication Method is EAP-TLS, no User Name and Password are required. Enter the Realm information supplied by your service provider. Click the Next button.•If the Authentication Method is EAP-TTLS/MS-CHAPv2, you will have to enter a User Name and Password and Realm information supplied by your Service Provider. Once you have entered the User Name/Password/Realm information, click the Next button.•If you are unsure of the Authentication Method, select EAP-TLS (this is the default) and click the Next button.

15Setup Wizard and AuthenticationStep 4 - AccountThe Account tab will allow you to manage Voice over IP (VoIP) related services. Please consult with your telephony service provider for these settings.Click the Apply button when finished.Congratulations! You have now completed the setup of your WiMAX connection. Click OK on the Congratulations! dialog box. A status screen will appear that shows Network status and telephony status. The Network Status screen will provide any status associated with your WiMAX Wireless Broadband connection. The Telephony Status screen provides status of your telephony service.

16Setup Wizard and AuthenticationStatus Screen•The Restart button will shut down the CPE device and restore all factory settings. Note: The restart button is available on every screen.•The Wizard button will prompt you to start the set-up wizard over again.•The Refresh button will refresh the status data.•The Auto Refresh button will allow the web browser to automatically refresh at the interval determined in the Control Panel menu.Restart Button

17Basic ConfigurationBasic ConfigurationOnce the CPE set up has been completed, you can login to your CPE from any computer on your home network by typing the device name in the address bar. The default device name is mywimax.This section describes the PERSONALIZE, INTERNET, and STATUS Menus that are available.Personalize MenuThe Personalize menu provides the following tabs:•Password •Device Time•Device Name•Restore Factory Settings

18Basic ConfigurationPersonalize MenuPassword TabThe password tab allows you to enable/disable password protection. You can also change your password here. Be sure to click the Apply button when finished.Field or Button DescriptionEnable Login Password ProtectionChecking this box will require login password protection.New Login PasswordEnter your new password here. Maximum 20 characters. Passwords are case-sensitive.Confirm New Login PasswordRe-enter your new password here, exactly as entered above.

19Basic ConfigurationDevice Time TabThe Device Time tab allows you to establish the time zone for your location. It also allows you to automatically adjust for Daylight Savings Time if necessary. Be sure to click the Apply button when finished.Device Name TabThe Device Name tab allows you to re-name your CPE device. This is the Device Name you enter on an internet browser address bar to access your CPE device. Be sure to click the Apply button when finished.Field or Button DescriptionCurrent Local TimeShows the current local date and time.Time Zone Select your local time zone from the drop down box.Auto Adjust for Daylight Saving TimeCheck this box if your location observes Daylight Savings Time. (Default is checked)Field or Button DescriptionNew Device NameEnter the new name for the CPE device. Maximum 20 characters.

20Basic ConfigurationRestore Factory Settings TabThe Restore Factory Settings Tab will reset your CPE to the manufacturers default settings. Be sure to click the Apply button if you are sure you want to reset factory settings.Field or Button DescriptionRestore Factory SettingsChecking this box will restore the CPE to factory default settings. The device will restart when you click Apply.

21Basic ConfigurationInternet MenuThe Internet menu provides the following tabs:•WiMAX Security•Internet Protocol•Firewall•Dynamic DNSInternet Menu

22Basic ConfigurationWiMAX Security TabThe WiMAX Security tab will contain your authentication method. Check with your service provider to determine if they require a user name and password for authentication purposes. If your authentication method is EAP-TLS, then a User Name & Password are not necessary.Click the Apply button.Internet Protocol TabPlease check with your service provider for these settings. If you are unsure of the settings, leave the default values set and click the Apply button.If your service provider has instructed you to change any of these settings, be sure to click the Apply button when you are finished.Field or Button DescriptionAuthentication MethodDrop down box allows you to select either EAP-TLS (default) or EAP-TTLS/MS-CHAPv2. User Name (EAP-TTLS/MS-CHAPv2 only)Enter the User Name supplied by your ser-vice provider.Password (EAP-TTLS/MS-CHAPv2 only)Enter the Password supplied by your service provider.RealmSupplied by your service provider.

23Basic ConfigurationFirewall TabA firewall helps to protect your home network from unauthorized access. It will also help to manage authorized access from the internet to your CPE.Be sure to click the Apply button once you are finished.Field or Button DescriptionEnable FirewallCheck this box to enable the firewall for your home network.Enable Web Login from Internet(Grayed out if Enable Firewall is not selected). Check this box to enables you to access your CPE device from a network other than your own.Web Login Port from InternetChoose a port number to connect to when logging in from a network other than your own. The default is 8080.Enable ping from Internet Enables the CPE to respond to a ping from the Internet. This option would be enabled to allow testing only. Do not leave this enabled.

24Basic ConfigurationDynamic DNS TabDynamic Domain Name Service (DDNS) allows a user with a non-static IP address to keep their domain name associated with an ever changing IP address. As an example, DDNS is used when you are hosting your own website.Be sure to click the Apply button once you are finished.Field or Button DescriptionEnable DDNS Check this box to Enable DDNS (default is unchecked).DDNS Service Provider Select DDNS Service Provider that you belong to from the drop down box. DDNS User Name Only valid if Enable DDNS is checked. Enter your DDNS account user name.DDNS PasswordOnly valid if Enable DDNS is checked. Enter your DDNS account password.DDNS Host NameOnly valid if Enable DDNS is checked. Enter the DDNS Host Name.This is assigned by the DDNS service.

25Basic ConfigurationStatus MenuThe Status menu provides the following tabs:•Network•TelephonyStatus MenuNetwork TabThe Network tab will provide any status associated with your WiMAX Wireless Broadband connection. Telephony TabThe Telephony tab will provide any status associated with yoru telephony connection.

26Basic ConfigurationTelephony MenuThe telephony menu allows you to manage your Voice over Internet Protocol (VoIP) services.Note: Contact your service provider to obtain VoIP service, if you do not already have this service.The Telephony menu provides the following tabs:•Account•Ring Tone•Caller Id•Call Forwarding•Voice Mail•Special NumbersTelephony Menu

27Basic ConfigurationAccount TabPlease consult with your service provider for these settings.Be sure to click the Apply button once you have made changes.Ring Tone TabThe Ring Tone tab allows you to customize ring tones for your telephone(s). Note: You will need a VoIP phone connected to your CPE to hear ring tones.Field or Button DescriptionRealmEnter Realm information as provided by your service provider.Line 1 User NameIf Line 1 is an active VoIP, enter the User Name as provided by your service provider.Line 1 PasswordEnter the Line 1 password as provided by your service provider. Passwords are case sensitive.Confirm Line 1 PasswordRe-enter your Line 1 password exactly as entered in the field above.Line 2 User NameIf Line 2 is an active VoIP, enter the User Name as provided by your service provider.Line 2 PasswordEnter the Line 2 password as provided by your service provider. Passwords are case sensitive.Confirm Line 2 PasswordRe-enter your Line 2 password exactly as entered in the field above.

28Basic ConfigurationBe sure to click the Apply button once you have made changes.Caller ID TabThe Caller ID tab allows you to manage the Caller ID functions for your telephones.Field or Button DescriptionDefault Line 1 Ring TypeUse the drop down box to select a ring tone for Line 1. The default is ringtone R0.TestClick to hear how the selected ring tone will sound.Default Line 2 Ring TypeUse the drop down box to select a ring tone for Line 2. The default is ringtone R0.TestClick to hear how the selected ring tone will sound.Field or Button DescriptionEnable Line 1 Anonymous Incoming Call RejectionIf Line 1 is your active telephone port, check this box if you would like to reject telephone calls from anonymous incoming callers. The default is checked.Enable Line 1 Permanent Anonymous Outgoing CallIf Line 1 is your active telephone port, check this box if you would like to permanently block your telephone number from appearing on others’ Caller ID. The default is unchecked.

29Basic ConfigurationBe sure to click the Apply button once you have made changes.Call Forwarding TabThe Call Fowarding tab allows you to manage the call forwarding features for your telephone(s).Enable Line 2 Anonymous Incoming Call RejectionIf Line 2 is your active telephone port, check this box if you would like to reject telephone calls from anonymous incoming callers. The default is checked.Enable Line 2 Permanent Anonymous Outgoing CallIf Line 2 is your active telephone port, check this box if you would like to permanently block your telephone number from appearing on others’ Caller ID. The default is unchecked.Field or Button DescriptionEnable Line 1 Basic ForwardingCheck this box to enable basic call forward-ing on Line 1. The default is unchecked.Line 1 Basic Forwarding to NumberIf “Enable Line 1 Basic Forwarding” is checked, enter the telephone number you would like to forward calls to.Enable Line 1 Forwarding on No AnswerCheck this box to forward calls received on Line 1 if there is no answer. This function is not available if “Enable Line 1 Basic For-warding is checked”.Field or Button Description

30Basic ConfigurationLine 1 No Answer Forwarding to NumberIf “Line 1 No Answer Forwarding to Num-ber” is checked, enter the telephone number you would like to forward calls to when there is no answer on Line 1. This function is not available if “Enable Line 1 Basic Forwarding is checked”.Line 1 No Answer Forwarding Ring CountEnter the number of rings allowed before the call forwards to the number identified above. The default is 6 rings. There is no minimum or maximum of rings allowed.Enable Line 1 Forwarding on BusyCheck this box to forward calls received while Line 1 is in use.Line 1 Busy Fowarding To NumberIf “Enable Line 1 Forwarding on Busy” is checked, enter the telephone number you would like calls forwarded to when Line 1 is in use.Enable Line 2 Basic ForwardingCheck this box to enable basic call forward-ing on Line 2. The default is unchecked.Line 2 Basic Forwarding to NumberIf “Enable Line 2 Basic Forwarding” is checked, enter the telephone number you would like to forward calls to.Enable Line 2 Forwarding on No AnswerCheck this box to forward calls received on Line 2 if there is no answer. This function is not available if “Enable Line 2 Basic For-warding is checked”.Field or Button Description

31Basic ConfigurationBe sure to click the Apply button once you have made changes.Line 2 No Answer Forwarding to NumberIf “Line 2 No Answer Forwarding to Num-ber” is checked, enter the telephone number you would like to forward calls to when there is no answer on Line 2. This function is not available if “Enable Line 2 Basic Forwarding is checked”.Line 2 No Answer Forwarding Ring CountEnter the number of rings allowed before the call forwards to the number identified above. The default is 6 rings. There is no minimum or maximum of rings allowed.Enable Line 2 Forwarding on BusyCheck this box to forward calls received while Line 2 is in use.Line 2 Busy Fowarding To NumberIf “Enable Line 2 Forwarding on Busy” is checked, enter the telephone number you would like calls forwarded to when Line 2 is in use.Field or Button Description

32Basic ConfigurationVoice Mail TabThe voice mail tab allows you to see the status of your voice mail. Note: Please contact your service provider to activate the voice mail feature if it is not already active.Be sure to click the Apply button once you have made changes.Special Number TabThe Special Number tab provides a list of special dialing numbers for your VoIP Phone Service.Field or Button DescriptionLine 1 Server Based Voice Mail StatusShows the status of Line 1 voice mail as either enabled or disabled.Line 1 Number of New Voice Mails Shows the number of new, unheard voice mails on Line 1.Line 1 Number of Old Voice Mails Shows the number of old, previously heard voice mails on Line 1.Line 2 Server Based Voice Mail StatusShows the status of Line 2 voice mail as either enabled or disabled.Line 2 Number of New Voice Mails Shows the number of new, unheard voice mails on Line 2.Line 2 Number of Old Voice Mails Shows the number of old, previously heard voice mails on Line 2.

33Basic ConfigurationThe following descriptions are valid for both Line 1 and Line 2.Field or Button DescriptionService Provider Contact Number Use this number to contact customer service for your service provider.Emergency Number Dial this number to reach local emergency services.Redial Dial this number to redial the last number called.Blind Call Transfer Dial this number to transfer a call directly to a third party.Consultation Call Transfer Dial this number to speak with the third party before you transfer the call to them.Call Hold Dial this number to place your current call on hold.Automatic Recall Activate Dial this number to call back the number of the last incoming call.Automatic Recall DeactivateDial this number to automatically call back the last number dialed when that number becomes available.Call Forwarding ActivateDial this number to forward your calls to a different number.Call Forwarding DeactivateDial this number to deactivate call forward-ing. Call Forwarding Busy ActivateDial this number to forward calls to a differ-ent number when the line is busy.Call Forwarding Busy DeactivateDial this number to de-activate calls from forwarding to a different number when the line is busy.

34Basic ConfigurationCall Forwarding Busy Change NumberDial this number to change the phone number to which calls will be forwarded when the line is busy.Call Forwarding No Answer ActivateDial this number to forward calls to a differ-ent number when there is no answer on Line 1 or Line 2.Call Forwarding No Answer DeactivateDial this number to de-activate calls from forwarding to a different number when there is no answer on Line 1 or Line 2.Call Forwarding No Answer Change NumberDial this number to change the phone number to which calls will be forwarded when there is no answer on Line 1 or Line 2.Automatic Callback ActivateDial this number to hear the most recent call you missed and to return the call. If the num-ber is busy, you can hang up.When the num-ber is available, your phone will ring. Pick up your phone and the call will be connected.Automatic Callback DeactivateDial this number to de-activate automatic callback.Do Not Disturb ActivateDial this number to have calls automatically routed to voice mail.Do Not Disturb DeactivateDial this number to cancel having calls auto-matically routed to voice mail.Calling Number Delivery BlockingDial this number to block your number from appearing on the Caller ID of the people you call. Your calls may appear as “Private” or “Anonymous”.Field or Button Description

35Basic ConfigurationLine Blocking DeactivateDial this number to unblock your telephone number from appearing on Caller ID.Call Waiting ToggleDial this number to toggle between call wait-ing ON and call waiting OFF.Anonymous Call Rejection ActivateDial this number to have anonymous calls rejected.Anonymous Call Rejection DeactivateDial this number to allow anonymous calls to go through.Field or Button Description

36Advanced ConfigurationAdvanced ConfigurationThe Advanced Configuration section describes the Port Forwarding, Local Address, and Control Panel menus.Port Fowarding MenuPort forwarding enables you to direct incoming traffic to specific LAN hosts (computers on your network) based on the protocol and port number. It is used to play Internet games or provide local services (such as web hosting) for a LAN group.The Port Forwarding menu provides the following tabs:•Basic•ForwardingPort Forwarding Menu

38Advanced ConfigurationForwarding TabClick on the ADD button to create additional Port Fowarding rules.Be sure to click the Apply button once you have made changes.Field or Button DescriptionSelectSelect a box when you want to delete the spe-cific row.ProtocolSelect TCP (Transmission Control Protocol) or UDP (User Datagram Protocol).WAN Port StartEnter the beginning port range for external network access.WAN Port EndEnter the ending port range for external net-work access.LAN IP AddressEnter the IP address to host the service.LAN Port StartEnter the beginning port range for internal network access.LAN Port EndEnter the ending port range for internal net-work access.EnabledCheck to enable specific port forwarding.

39Advanced ConfigurationLocal Address MenuThe Local Address menu allows you to configure your Local Area Network (LAN) connections.The Local Address menu provides the following tabs:•DHCP Server•Lease Status•Lease ReservationLocal Address Menu

40Advanced ConfigurationDHCP Server TabThe DHCP Server tab enables Dynamic Host Configuration Protocol (DHCP) server functionality on the LAN, allowing the router to dynamically assign lease IP addresses to clients that connect to it from the local network.Field or Button DescriptionEnable DHCP Server If selected, the DHCP server on the gateway assigns IP addresses to the computers and other hosts on your network if they have DHCP enabled. By default, the gateway server is enabled. If there is another DHCP server running on your network (on another router), you must disable one of the DHCP servers.DHCP Server IP AddressEnter the default port forwarding LAN Client IP Address. DHCP Starting IP AddressSets the first IP address assigned by the DHCP server, in dotted-decimal format. It must be greater than the IP address value of the gateway. For example, if the IP address of the gateway is 192.168.15.1 (default), the starting IP address must be 192.168.15.2 (or higher).DHCP Ending IP Address Sets the final IP address assigned by the DHCP server. If the DHCP server runs out of DHCP addresses, users cannot access network resources. If this happens, increase the Ending IP or reduce the Lease Time.

41Advanced ConfigurationBe sure to click the Apply button once you have made changes.DHCP Lease TimeSets the time, in seconds, that a network computer remains connected to the gateway using its current assigned IP address. At the end of this time, the DHCP server renews the lease or assigns the computer a new IP address. The default is 3600 seconds (1 hour). The maximum is 999999 seconds (about 278 hours).Field or Button Description

42Advanced ConfigurationLease Status TabThe Lease Status tab in the Local Address menu displays the active DHCP leases since the last reboot.Be sure to click the Apply button once you have made changes.Field or Button DescriptionClient Host NameDisplays the client host name. The Name field is limited to 20 characters (only 5 appear in display).MAC AddressMedia Access Control (MAC) address. IP AddressShows the IP Address for each active lease.Remaining Lease DurationShows the amount of time, in seconds, remaining in the lease.

43Advanced ConfigurationLease Reservation TabThis tab allows you to manage the lease reservation so that the same client receives the same IP address each time.Be sure to click the Apply button once you have made changes.Field or Button DescriptionSelectSelect this box if you want to delete an estab-lished lease reservation. Be sure to click the Delete button once you have selected your exception to be deleted.Client Host NameEnter the client host name. The Name field is limited to 20 characters (only 5 appear in dis-play)MAC AddressMedia Access Control (MAC) address. Enter the MAC address of the device.IP AddressEnter the IP address that you want assigned to the MAC Address.EnabledChecking this box enables the lease reserva-tion.

44Advanced ConfigurationControl PanelThe Control Panel sections allows you to view/update your software information. The Control menu provides the following tabs:•Software•Certificate•System•AboutControl Panel Menu

45Advanced ConfigurationSoftware TabThe Software tab manages the software on your CPE device. It is also where you can upgrade device software.Use the BROWSE button to browse your computer for additional software packages. Once you have located the software package/update you would like to add to your device, click on the Upgrade button.You should see the available software updates in the “Available Software Packages” table. If you cannot see the list, click the View button.Select the software you would like to install and click the Install button.If you would like to remove software, select the software package you would like to remove and click Uninstall.Certificate TabThe Certificate tab is where you manage the certificates that are stored on the device.Use the BROWSE button to locate the certificate file on your computer, and then click the IMPORT button.Use the REMOVE button to remove any selected certificate(s).

46Advanced ConfigurationSystem TabThis tab allows you to manage additional features of your CPE device.Be sure to click the Apply button once you have made changes.About TabThe About Tab will display basic properties of your CPE device such as: Product Name, Model ID, Hardware Version, Serial Number and the WiMAX MAC Address.Field or Button DescriptionLanguage Used in User InterfaceSelect the desired language for the user interface. The default language is English.Enable WiMAX Radio InterfaceCheck this box to enable the WiMAX Radio Interface.Enable LEDChecking this box enables the LEDs on the front of your CPE device.Auto Refresh IntervalEnter, in seconds, the interval for status Auto Refresh. Valid range is 2 seconds - 9999 seconds. The default value is 3 sec-onds.Rebootstrap EMSCheck this box to reconnect the device with the EMS.Note: Only perform this function under the supervision of a Customer Support Representative.

47Configuring TCP/IPConfiguring TCP/IPThis chapter is needed for setup procedures.All client computers on your network must be configured for TCP/IP (the protocol that controls communication among computers). Perform one of:•Configuring TCP/IP in Windows 2000•Configuring TCP/IP in Windows XPNote: Follow the instructions in your Macintosh or UNIX user manualConfiguring TCP/IP in Windows 20001On the Windows Desktop, click Start.2Select Settings and then Control Panel from the pop-up menus to display the Control Panel window:

48Configuring TCP/IPWindows Control Panel3Double-click the Network and Dial-up Connections icon to display the Network and Dial-up Connections window:Network and Dial-up ConnectionsIn the steps that follow, a connection number like 1, 2, 3, etc., is a reference that is displayed on computers with multiple network interfaces. Computers with only one network interface may only see the label: Local Area Connection.

49Configuring TCP/IP4Click Local Area Connection number. The value of number varies from system to system. The Local Area Connection number Status window is displayed:Local Area Connection5Click Properties. Information similar to the following window is displayed:Properties

50Configuring TCP/IP6If Internet Protocol (TCP/IP) is in the list of components, TCP/IP is installed. You can skip to Step 10.If Internet Protocol (TCP/IP) is not in the list, click Install. The Select Network Component Type window is displayed:Select Network Connection Type7Click Protocol on the Select Network Component Type window and click Add. The Select Network Protocol window is displayed:Select Network ProtocolNote: You might have to use the scroll bar to locate the Internet Protocol (TCP/IP) setting.8Click Internet Protocol (TCP/IP).9Click OK. The Local Area Connection number Properties window is re-displayed.

51Configuring TCP/IP10Be sure the box next to Internet Protocol (TCP/IP) is checked.11 Click Properties. The Internet Protocol (TCP/IP) Properties window is displayed:Internet Protocol (TCP/IP) Properties12Be sure Obtain IP address automatically and Obtain DNS server address automatically are selected.13 Click OK to accept the TCP/IP settings.14 Click Close to close the Local Area Connection number Properties window.15 Click OK16If prompted to restart the computer and click OK again.Configuring TCP/IP in Windows XP1On the Windows desktop, click Start to display the Start window:

52Configuring TCP/IPWindows XP Start Window2Click Control Panel to display the Control Panel window. The display varies, depending on your Windows XP view options. If the display is a Category view as shown below, continue with Step 3. Otherwise, skip to Step 5Control Panel3Click Network and Internet Connections to display the Network and Internet Connections window:

53Configuring TCP/IPNetwork and Internet Connections4Click Network Connections. Skip to Step 6.5If a classic view similar to below is displayed, double-click Network Connections to display the LAN or High-speed Internet connections.Control Panel Classic View6Right-click the Local Area Connection. If more than one connection is displayed, be sure to select the one for your network interface.

54Configuring TCP/IPNetwork Connections7Select Properties from the pop-up menu to display the Local Area Connection Properties window:Local Area Connection Properties8On the Local Area Connection Properties window, select Internet Protocol (TCP/IP) if it is not selected.9Click Properties to display the Internet Protocol (TCP/IP) Properties window:

55Configuring TCP/IPInternet Protocol (TCP/IP) Properties10 Be sure Obtain IP address automatically and Obtain DNS server address automatically are selected.11Click OK to close the TCP/IP Properties window.

56TroubleshootingTroubleshootingPower LED is Off•Check that the AC power adapter is properly plugged into the electrical outlet and into the Desktop CPE.•Check that the electrical outlet is working.A Computer Cannot Log On to the CPECheck that the Ethernet cable is properly connected to the Desktop CPE unit and the computer.Cannot Connect to the Internet•Check the Desktop CPE connection status from the Web Interface, refer to the Connection Status section to verify the connection status.•If the Desktop CPE connection is down, and the gateway has not received an IP for 5 to 10 minutes:- Re-Run the Setup Wizard.- If the Setup Wizard does not help, then reset the Desktop CPE using the reset button. Additional Troubleshooting Help•Contact your service provider for additional help.

57Important Safety and Legal InformationImportant Safety and Legal InformationYour Motorola WiMAX Wireless Broadband Gateway is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to RF electromagnetic energy.This Product complies with the following RF energy exposure standards and guidelines:•United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J•American National Standards Institute (ANSI)/ Institute of Electrical and Electronic Engineers (IEEE) C95 1-2005•Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition•International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998•Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radio frequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999•Australian Communications Authority Radiocommunications (Electromagnetic Radiation - Human Exposure) Standard, 2003•ANATEL ANNEX to Resolution No. 303 of July 2, 2002 “Regulation of Limitation of Exposure to Electrical,

58Important Safety and Legal InformationMagnetic, and Electromagnetic Fields in the Radio Frequency Range Between 9 kHz and 300 GHz” and “Attachment to Resolution #303 from July 2, 2002”RF Exposure Compliance and Guidelines Operating InstructionsTo comply with FCC RF energy exposure requirements, this Gateway desktop transmitter should be operated at a minimum separation distance of 20 cm from all persons.For additional information on exposure requirements or other training information, visit http://www. motorola.com/rfhealthFCC Regulatory InformationThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

59Important Safety and Legal InformationEU Declaration of Conformity

60Important Safety and Legal Information

61Important Safety and Legal InformationIn compliance with national requirements, a power supply cord with a cross-sectional area of 0.75mm2 minimum for each individual conductor, will be provided when the product is submitted for national approval.

62Important Safety and Legal InformationCaring for the EnvironmentThe following information is provided to enable regulatory compliance with the European Union (EU) Directive 2002/96/EC Waste Electrical and Electronic Equipment (WEEE) when using Motorola Networks equipment in EU countries.Disposal of Motorola Equipment in EU CountriesThis product is compliant with the requirements of the European Union Restriction of Hazardous Substances (EU RoHS) directive.Please do not dispose of Motorola Networks equipment in landfill sites.In the EU, Motorola Networks in conjunction with a recycling part-ner will ensure that equipment is collected and recycled according to the requirements of EU environmental law.

63Important Safety and Legal InformationDisposal of Motorola Networks Equipment in Non-EU countriesIn non-EU countries, dispose of Motorola Networks equipment in accordance with national and regional regulations.

64CMM DisclosureCMM DisclosureThe China Management Methods (CMM) Disclosure Table is intended only to communicate compliance with China requirements; it is not intended to communicate compliance with EU RoHS or any other environmental requirements.

65CMM DisclosureCMM Disclosure Information

66Copyrights and TrademarksCopyrights and TrademarksNoticeWhile reasonable efforts have been made to assure the accuracy of this document, Motorola, Inc. assumes no liability resulting from any inaccuracies or omissions in this document, or from use of the information obtained herein. The information in this document has been carefully checked and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies or omissions. Motorola, Inc. reserves the right to make changes to any products described herein and reserves the right to revise this document and to make changes from time to time in content hereof with no obligation to notify any person of revisions or changes. Motorola, Inc. does not assume any liability arising out of the application or use of any product, software, or circuit described herein; neither does it convey license under its patent rights or the rights of others.It is possible that this publication may contain references to, or information about Motorola products (machines and programs), programming, or services that are not announced in your country. Such references or information must not be construed to mean that Motorola intends to announce such Motorola products, programming, or services in your country.CopyrightsThis instruction manual, and the Motorola products described in this instruction manual may be, include or describe copyrighted

67Copyrights and TrademarksMotorola material, such as computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola and its licensors certain exclusive rights for copyrighted material, including the exclusive right to copy, reproduce in any form, distribute and make derivative works of the copyrighted material. Accordingly, any copyrighted material of Motorola and its licensors contained herein or in the Motorola products described in this instruction manual may not be copied, reproduced, distributed, merged or modified in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, as arises by operation of law in the sale of a product.Usage and Disclosure RestrictionsLicense AgreementsThe software described in this document is the property of Motorola, Inc and its licensors. It is furnished by express license agreement only and may be used only in accordance with the terms of such an agreement.Copyrighted MaterialsSoftware and documentation are copyrighted materials. Making unauthorized copies is prohibited by law. No part of the software or documentation may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, without prior written permission of Motorola, Inc.

Navigation menu