Nokia Solutions and Networks CPE25300 Non-line of Sight Wireless Data Link User Manual 285a66

Nokia Solutions and Networks Non-line of Sight Wireless Data Link 285a66

UserManual.wiki >

Nokia Solutions and Networks >

CPE25300 User Manual >

Manual HTML Version

Manual

-1

Contents

Desktop CPEi 300 User Guide

Overview. . . . . . . . . . . . . 1

Powerful Features in a

Single Unit . . . . . . . . . . . 3

Front of CPE . . . . . . . . . . 3

Back of CPE . . . . . . . . . . 6

Operating Information. . . 7

Overview. . . . . . . . . . . . . 7

Before You Begin . . . . . . 7

Easy Setup. . . . . . . . . . . . 9

Advanced Setup . . . . . . 10

Before you Begin

Configuration . . . . . . . . 11

Logging In to the CPE. . 11

Setup Wizard and Authentication

Step 1 - Change Password 13

Step 2 - Device Time. . . 14

Step 3 - WiMAX Security 14

Step 4 - Account . . . . . . 15

Basic Configuration

Personalize Menu . . . . . 17

Internet Menu . . . . . . . . 21

Status Menu. . . . . . . . . . 25

Telephony Menu . . . . . . 26

Contents

Advanced Configuration

Port Fowarding Menu. . . 36

Local Address Menu . . . 39

Control Panel . . . . . . . . . 44

Configuring TCP/IP

Configuring TCP/IP in

Windows 2000 . . . . . . . . 47

Configuring TCP/IP in

Windows XP. . . . . . . . . . 51

Troubleshooting

Power LED is Off. . . . . . 56

A Computer Cannot

Log On to the CPE . . . . . 56

Cannot Connect to

the Internet . . . . . . . . . . . 56

Additional Troubleshooting

Help . . . . . . . . . . . . . . . . 56

Important Safety and Legal Information

Disposal of Motorola Equipment in

EU Countries . . . . . . . . . 62

Disposal of Motorola

Networks Equipment in

Non-EU countries. . . . . . 63

CMM Disclosure

Copyrights and Trademarks

Notice . . . . . . . . . . . . . . . 66

Copyrights . . . . . . . . . . . 66

Usage and Disclosure

Restrictions. . . . . . . . . . . 67

Trademarks. . . . . . . . . . . 68

Desktop CPEi 300 User Guide

Desktop CPEi 300 User

Guide

Overview

Thank you for purchasing the Motorola CPE Indoor (CPEi) 300

desktop device. The Desktop CPEi allows you to connect to the

wireless world easily and seamlessly without complicated installa-

tion and setup procedures. In addition it offers you the ability to

make Voice over Internet Protocol (VoIP) calls.

The Desktop CPE indoor (CPEi) device provides the user:

•

Convenience — with easy plug and play functionality.

Compact design.

•

Performance — dual antennas supply diversity technology.

Best in Class range and indoor penetration.

•

Control — remote management capability allows easy

detection and authentication once the unit is setup.

•

VoIP - two RJ11 ports allow for Voice over IP calls using

your CPEi 300.

Desktop CPEi 300 User Guide

Desktop CPEi 300

The features and the physical appearance of your Desktop CPEi

device may differ slightly from the illustration.

This product is subject to change. For the most recent

documentation, visit the Product Documentation page on

www.motorola.com.

Desktop CPEi 300 User Guide

Powerful Features in a Single Unit

The CPE device provides the following features:

•

WiMAX Authentication

•

WAN DHCP Client

•

LAN DHCP Server

•

Home Gateway Functions

Front of CPE

The Front of the CPE units contain LED Link/Activity indicators.

The LEDs provide the status of the unit and signal strength

indicators for easy adjustment during setup.

Front of Unit

Desktop CPEi 300 User Guide

LED Indicator Interface

Power Status

The Power LED indicator is:

•

On — power to CPE is on.

•

Off — power to the CPE is off.

Ethernet Status The Ethernet LED indicator is:

•

On - LAN Ethernet link has been

established.

•

Blinking - LAN Ethernet activity

has been detected.

•

Off - LAN Ethernet link has been

dropped.

Signal Strength Full WiMAX Signal Strength is

detected if all WiMAX Signal Strength

LEDs are lit.

•

All WiMAX Signal Strength

LEDs are off - low signal

detected.

•

First WiMAX Signal Strength

LED is lit - low signal detected.

•

First and second WiMAX Signal

Strength LED is lit - high signal

detected.

Desktop CPEi 300 User Guide

Caution:

If the Power LED and all 3 WiMAX Signal Strength

LEDs are blinking, then a software upgrade is in progress. Do NOT

remove power to the CPE.

Note:

If the Power LED is BLINKING and all 3 WiMAX Signal

Strength LEDs are OFF, the CPE device is overheating, and you

will not have service.

WAN WiMAX While acquiring access to the WiMAX

Network:

•

The Power LED is ON.

•

The WAN LED is OFF.

•

All WiMAX Signal Strength

LEDs will be in vary between

ON, OFF and/or BLINKING

status.

Once connectivity to the WiMAX

Network is established:

•

The Power LED is ON.

•

The WAN LED is ON.

When WiMAX traffic is detected:

•

The Power LED is ON.

•

The WAN LED is BLINKING.

Desktop CPEi 300 User Guide

Back of CPE

The back of the CPE unit contains the reset switch, AC Power

Connector, Ethernet connector, Line 1 and Line 2 telephone ports,

and the External Antenna Connector (accessory available from your

service provider).

Back of the Unit

Port Descriptions

Back Panel Ports Description

External Antenna External Antenna Connector

Ethernet Ethernet Port

Power AC Power Connector

Reset

Note:

Hardware Reset Button (A

paperclip is recommended for accessing

this button). Before resetting the CPE,

ensure the power LED is ON.

Phone Line 1 RJ-11 port for use with VoIP.

Phone Line 2 RJ-11 port for use with VoIP.

Desktop CPEi 300 User Guide

Operating Information

Operating temperature for this unit is 0-40C (32-104F).

Installation

Overview

To install the Desktop CPEi 300 Series, you need to review the

following sections:

•

Before You Begin

•

Easy Setup

Before You Begin

Before you begin installation, check that you have received the

following items with your Desktop CPEi 300:

In the box with your CPE you should have:

Item Description

AC Adapter

Power adapter and cord connects the

Desktop CPE to an AC electrical outlet.

Ethernet Cable The ethernet cable connects the Internet

port on your Desktop CPE to your PC or

laptop computer.

Desktop CPEi 300

Quick Start Guide

Provides quick installation instructions

for getting your Desktop CPE up and

running.

Desktop CPEi 300 User Guide

In addition, you will also need:

•

A computer

•An RJ-11 telephone cable (optional). Two RJ-11

telephone cables will be required if your service

provider has supplied you with two telephone

numbers.

Desktop CPEi 300 User Guide

Easy Setup

The CPE is easily set up in your home. Basic installation equipment

needed are the power adapter and cord, Ethernet cable, a PC or lap-

top computer and the CPE device. If you want to use the VoIP func-

tionality, you will also need an RJ-11 phone cable and a telephone.

Perform the following tasks before attaching the power cord or

powering up the unit:

•

Stand the CPE on a flat surface.

•

Plug the power adapter into the power connector on the back

of the unit.

•

Plug the AC power cord into an AC outlet. The unit will turn

on.

•

Plug one end of the Ethernet cable into the Ethernet

connector on the back of the unit.

•

Plug the other end of the Ethernet cable into the Ethernet

connector of your computer.

•

To use VoIP functionality of the phone, plug one end of the

phone line into the activated phone connector on the back of

the unit. Phone line activation is dependent upon your

service contract.

•

Plug the other end of the phone line into the phone line

connector of your telephone.

Desktop CPEi 300 User Guide

Advanced Setup

The CPE can also be used to connect to a multi-port switch (hub) -

purchased separately from the CPE. Connecting the CPE device to

a hub will allow you to connect more than one computer to your

CPE device. See the picture below for an example.

Desktop CPEi 300 User Guide

Procedure to Log into the CPE

Before you Begin Configuration

Some settings on your computer must be verified or changed to

ensure that your computer configuration can support the Desktop

CPE.

Verify that the IP addresses and DNS settings are automatically

generated in your Local Area connection of your Internet Protocol

(TCP/IP) properties. Refer to the chapter titled “Configuring

TCP/IP” for information on how to do this.

Logging In to the CPE

Use the following procedure to log into the Desktop CPE.

On a computer that is connected to the Desktop CPEi, open a

web browser.

In the Address or Location field, type

http://mywimax.

and

press

ENTER

to display the login screen.

Note:

You must include the period (.) after http://mywimax. in

order to access the login screen.

The Welcome to Motorola WiMAX CPE screen will be

displayed and will prompt you for a password.

Desktop CPEi 300 User Guide

4In the Password field, type the password (default is motorola).

Click

First time users will see a pop-up box that states: “

The Wizard

application will guide you through for the first time

configuration. Click OK button to continue.”

7Click the OK button to launch the wizard application.

Setup Wizard and Authentication

Setup Wizard and

Authentication

Step 1 - Change Password

Once you have launched the setup wizard, you will be prompted to

change your password. Motorola recommends using a password to

protect your home network and CPE device. Passwords are

case-sensitive.

To change your password:

•

Ensure the “Enable Login Password Protection” box is

checked.

•Enter a New Login Password in the box. Passwords can be

no more than 20 characters in length.

•

Re-type your new password in the Confirm New Login

Password box.

•

Click

Next.

Note:

If you forget your password, you can reset it back to the

default (motorola) by pressing and holding the reset button on the

back of your CPE for more than 5 seconds. Before resetting the

CPE, ensure the power LED is ON.

Setup Wizard and Authentication

Step 2 - Device Time

This screen allows you to set the time zone and to enable Daylight

Savings Time (when applicable) for your location.

•

Select the appropriate time zone for your location from the

drop down box.

•

Check the box called “Auto Adjust for Daylight Savings

Time” if you live in a region that observes Daylight Savings

Time (this box is checked by default).

•

Click the

button.

Step 3 - WiMAX Security

The WiMAX Security tab will contain your authentication method.

Check with your service provider to determine if they require a user

name and password for authentication purposes.

•

If the Authentication Method is EAP-TLS, no User Name

and Password are required. Enter the Realm information

supplied by your service provider. Click the

button.

•

If the Authentication Method is EAP-TTLS/MS-CHAPv2,

you will have to enter a User Name and Password and

Realm information supplied by your Service Provider. Once

you have entered the User Name/Password/Realm

information, click the

button.

•

If you are unsure of the Authentication Method, select

EAP-TLS (this is the default) and click the

button.

Setup Wizard and Authentication

Step 4 - Account

The Account tab will allow you to manage Voice over IP (VoIP)

related services. Please consult with your telephony service

provider for these settings.

Click the

Apply

button when finished.

Congratulations! You have now completed the setup of your

WiMAX connection.

Click

on the Congratulations! dialog box.

A status screen will appear that shows Network status and

telephony status. The Network Status screen will provide any status

associated with your WiMAX Wireless Broadband connection. The

Telephony Status screen provides status of your telephony service.

Setup Wizard and Authentication

Status Screen

•

The

Restart

button will shut down the CPE device and

restore all factory settings.

Note:

The restart button is available on every screen.

•

The

Wizard

button will prompt you to start the set-up

wizard over again.

•

The

Refresh

button will refresh the status data.

•

The

Auto Refresh

button will allow the web browser to

automatically refresh at the interval determined in the

Control Panel menu.

Restart Button

Basic Configuration

Once the CPE set up has been completed, you can login to your

CPE from any computer on your home network by typing the

device name in the address bar. The default device name is

mywimax.

This section describes the PERSONALIZE, INTERNET, and

STATUS Menus that are available.

Personalize Menu

The Personalize menu provides the following tabs:

•

Password

•

Device Time

•

Device Name

•

Restore Factory Settings

Basic Configuration

Personalize Menu

Password Tab

The password tab allows you to enable/disable password

protection. You can also change your password here. Be sure to

click the

Apply

button when finished.

Field or Button Description

Enable Login

Password

Protection

Checking this box will require login

password protection.

New Login

Password

Enter your new password here. Maximum 20

characters. Passwords are case-sensitive.

Confirm New

Re-enter your new password here, exactly as

entered above.

Basic Configuration

Device Time Tab

The Device Time tab allows you to establish the time zone for your

location. It also allows you to automatically adjust for Daylight

Savings Time if necessary. Be sure to click the

Apply

button when

finished.

Device Name Tab

The Device Name tab allows you to re-name your CPE device. This

is the Device Name you enter on an internet browser address bar to

access your CPE device. Be sure to click the

Apply

button when

finished.

Field or Button Description

Current Local

Time

Shows the current local date and time.

Time Zone Select your local time zone from the drop

down box.

Auto Adjust for

Daylight Saving

Time

Check this box if your location observes

Daylight Savings Time. (Default is checked)

Field or Button Description

New Device

Name

Enter the new name for the CPE device.

Maximum 20 characters.

Basic Configuration

Restore Factory Settings Tab

The Restore Factory Settings Tab will reset your CPE to the

manufacturers default settings. Be sure to click the

Apply

button if

you are sure you want to reset factory settings.

Field or Button Description

Restore Factory

Settings

Checking this box will restore the CPE to

factory default settings. The device will

restart when you click Apply.

Basic Configuration

Internet Menu

The Internet menu provides the following tabs:

•

WiMAX Security

•

Internet Protocol

•

Firewall

•

Dynamic DNS

Internet Menu

Basic Configuration

WiMAX Security Tab

The WiMAX Security tab will contain your authentication method.

Check with your service provider to determine if they require a user

name and password for authentication purposes.

If your authentication method is EAP-TLS, then a User Name &

Password are not necessary.

Click the

Apply

button.

Internet Protocol Tab

Please check with your service provider for these settings. If you

are unsure of the settings, leave the default values set and click the

Apply

button.

If your service provider has instructed you to change any of these

settings, be sure to click the

Apply

button when you are finished.

Field or Button Description

Authentication

Method

Drop down box allows you to select either

EAP-TLS (default) or

EAP-TTLS/MS-CHAPv2.

User Name

(EAP-TTLS/MS-

CHAPv2 only)

Enter the User Name supplied by your ser-

vice provider.

Password

(EAP-TTLS/MS-

CHAPv2 only)

Enter the Password supplied by your service

provider.

Realm

Supplied by your service provider.

Basic Configuration

Firewall Tab

A firewall helps to protect your home network from unauthorized

access. It will also help to manage authorized access from the

internet to your CPE.

Be sure to click the

Apply

button once you are finished.

Field or Button Description

Enable Firewall

Check this box to enable the firewall for your

home network.

Enable Web

Internet

(Grayed out if Enable Firewall is not

selected).

Check this box to enables you to access your

CPE device from a network other than your

own.

Web Login Port

from Internet

Choose a port number to connect to when

logging in from a network other than your

own. The default is 8080.

Enable ping from

Internet Enables the CPE to respond to a ping from

the Internet. This option would be enabled to

allow testing only. Do not leave this enabled.

Basic Configuration

Dynamic DNS Tab

Dynamic Domain Name Service (DDNS) allows a user with a

non-static IP address to keep their domain name associated with an

ever changing IP address. As an example, DDNS is used when you

are hosting your own website.

Be sure to click the

Apply

button once you are finished.

Field or Button Description

Enable DDNS Check this box to Enable DDNS (default is

unchecked).

DDNS Service

Provider Select DDNS Service Provider that you

belong to from the drop down box.

DDNS User

Name Only valid if Enable DDNS is checked. Enter

your DDNS account user name.

DDNS Password

Only valid if Enable DDNS is checked. Enter

your DDNS account password.

DDNS Host

Name

Only valid if Enable DDNS is checked. Enter

the DDNS Host Name.This is assigned by

the DDNS service.

Basic Configuration

Status Menu

The Status menu provides the following tabs:

•

Network

•

Telephony

Status Menu

Network Tab

The Network tab will provide any status associated with your

WiMAX Wireless Broadband connection.

Telephony Tab

The Telephony tab will provide any status associated with yoru

telephony connection.

Basic Configuration

Telephony Menu

The telephony menu allows you to manage your Voice over Internet

Protocol (VoIP) services.

Note:

Contact your service provider to obtain VoIP service, if you

do not already have this service.

The Telephony menu provides the following tabs:

•

Account

•

Ring Tone

•

Caller Id

•

Call Forwarding

•

Voice Mail

•

Special Numbers

Telephony Menu

Basic Configuration

Account Tab

Please consult with your service provider for these settings.

Be sure to click the

Apply

button once you have made changes.

Ring Tone Tab

The Ring Tone tab allows you to customize ring tones for your

telephone(s).

Note:

You will need a VoIP phone connected to your CPE to hear

ring tones.

Field or Button Description

Realm

Enter Realm information as provided by your

service provider.

Line 1 User

Name

If Line 1 is an active VoIP, enter the User

Name as provided by your service provider.

Line 1 Password

Enter the Line 1 password as provided by

your service provider. Passwords are case

sensitive.

Confirm Line 1

Password

Re-enter your Line 1 password exactly as

entered in the field above.

Line 2 User

Name

If Line 2 is an active VoIP, enter the User

Name as provided by your service provider.

Line 2 Password

Enter the Line 2 password as provided by

your service provider. Passwords are case

sensitive.

Confirm Line 2

Password

Re-enter your Line 2 password exactly as

entered in the field above.

Basic Configuration

Be sure to click the

Apply

button once you have made changes.

Caller ID Tab

The Caller ID tab allows you to manage the Caller ID functions for

your telephones.

Field or Button Description

Default Line 1

Ring Type

Use the drop down box to select a ring tone

for Line 1. The default is ringtone R0.

Test

Click to hear how the selected ring tone will

sound.

Default Line 2

Ring Type

Use the drop down box to select a ring tone

for Line 2. The default is ringtone R0.

Test

Click to hear how the selected ring tone will

sound.

Field or Button Description

Enable Line 1

Anonymous

Incoming Call

Rejection

If Line 1 is your active telephone port, check

this box if you would like to reject telephone

calls from anonymous incoming callers. The

default is checked.

Enable Line 1

Permanent

Anonymous

Outgoing Call

If Line 1 is your active telephone port, check

this box if you would like to permanently

block your telephone number from appearing

on others’ Caller ID. The default is

unchecked.

Basic Configuration

Be sure to click the

Apply

button once you have made changes.

Call Forwarding Tab

The Call Fowarding tab allows you to manage the call forwarding

features for your telephone(s).

Enable Line 2

Anonymous

Incoming Call

Rejection

If Line 2 is your active telephone port, check

this box if you would like to reject telephone

calls from anonymous incoming callers. The

default is checked.

Enable Line 2

Permanent

Anonymous

Outgoing Call

If Line 2 is your active telephone port, check

this box if you would like to permanently

block your telephone number from appearing

on others’ Caller ID. The default is

unchecked.

Field or Button Description

Enable Line 1

Basic Forwarding

Check this box to enable basic call forward-

ing on Line 1. The default is unchecked.

Line 1 Basic

Forwarding to

Number

If “Enable Line 1 Basic Forwarding” is

checked, enter the telephone number you

would like to forward calls to.

Enable Line 1

Forwarding on

No Answer

Check this box to forward calls received on

Line 1 if there is no answer. This function is

not available if “Enable Line 1 Basic For-

warding is checked”.

Field or Button Description

Basic Configuration

Line 1 No

Answer

Forwarding to

Number

If “Line 1 No Answer Forwarding to Num-

ber” is checked, enter the telephone number

you would like to forward calls to when there

is no answer on Line 1. This function is not

available if “Enable Line 1 Basic Forwarding

is checked”.

Line 1 No

Answer

Forwarding

Ring Count

Enter the number of rings allowed before the

call forwards to the number identified above.

The default is 6 rings. There is no minimum

or maximum of rings allowed.

Enable Line 1

Forwarding on

Busy

Check this box to forward calls received

while Line 1 is in use.

Line 1 Busy

Fowarding To

Number

If “Enable Line 1 Forwarding on Busy” is

checked, enter the telephone number you

would like calls forwarded to when Line 1 is

in use.

Enable Line 2

Basic Forwarding

Check this box to enable basic call forward-

ing on Line 2. The default is unchecked.

Line 2 Basic

Forwarding to

Number

If “Enable Line 2 Basic Forwarding” is

checked, enter the telephone number you

would like to forward calls to.

Enable Line 2

Forwarding on

No Answer

Check this box to forward calls received on

Line 2 if there is no answer. This function is

not available if “Enable Line 2 Basic For-

warding is checked”.

Field or Button Description

Basic Configuration

Be sure to click the

Apply

button once you have made changes.

Line 2 No

Answer

Forwarding to

Number

If “Line 2 No Answer Forwarding to Num-

ber” is checked, enter the telephone number

you would like to forward calls to when there

is no answer on Line 2. This function is not

available if “Enable Line 2 Basic Forwarding

is checked”.

Line 2 No

Answer

Forwarding

Ring Count

Enter the number of rings allowed before the

call forwards to the number identified above.

The default is 6 rings. There is no minimum

or maximum of rings allowed.

Enable Line 2

Forwarding on

Busy

Check this box to forward calls received

while Line 2 is in use.

Line 2 Busy

Fowarding To

Number

If “Enable Line 2 Forwarding on Busy” is

checked, enter the telephone number you

would like calls forwarded to when Line 2 is

in use.

Field or Button Description

Basic Configuration

Voice Mail Tab

The voice mail tab allows you to see the status of your voice mail.

Note:

Please contact your service provider to activate the voice

mail feature if it is not already active.

Be sure to click the

Apply

button once you have made changes.

Special Number Tab

The Special Number tab provides a list of special dialing numbers

for your VoIP Phone Service.

Field or Button Description

Line 1 Server

Based Voice Mail

Status

Shows the status of Line 1 voice mail as

either enabled or disabled.

Line 1 Number of

New Voice Mails Shows the number of new, unheard voice

mails on Line 1.

Line 1 Number of

Old Voice Mails Shows the number of old, previously heard

voice mails on Line 1.

Line 2 Server

Based Voice Mail

Status

Shows the status of Line 2 voice mail as

either enabled or disabled.

Line 2 Number of

New Voice Mails Shows the number of new, unheard voice

mails on Line 2.

Line 2 Number of

Old Voice Mails Shows the number of old, previously heard

voice mails on Line 2.

Basic Configuration

The following descriptions are valid for both Line 1 and Line 2.

Field or Button Description

Service Provider

Contact Number Use this number to contact customer service

for your service provider.

Emergency

Number Dial this number to reach local emergency

services.

Redial Dial this number to redial the last number

called.

Blind Call

Transfer Dial this number to transfer a call directly to

a third party.

Consultation Call

Transfer Dial this number to speak with the third party

before you transfer the call to them.

Call Hold Dial this number to place your current call on

hold.

Automatic Recall

Activate Dial this number to call back the number of

the last incoming call.

Automatic Recall

Deactivate

Dial this number to automatically call back

the last number dialed when that number

becomes available.

Call Forwarding

Activate

Dial this number to forward your calls to a

different number.

Call Forwarding

Deactivate

Dial this number to deactivate call forward-

ing.

Call Forwarding

Busy Activate

Dial this number to forward calls to a differ-

ent number when the line is busy.

Call Forwarding

Busy Deactivate

Dial this number to de-activate calls from

forwarding to a different number when the

line is busy.

Basic Configuration

Call Forwarding

Busy Change

Number

Dial this number to change the phone number

to which calls will be forwarded when the

line is busy.

Call Forwarding

No Answer

Activate

Dial this number to forward calls to a differ-

ent number when there is no answer on Line

1 or Line 2.

Call Forwarding

No Answer

Deactivate

Dial this number to de-activate calls from

forwarding to a different number when there

is no answer on Line 1 or Line 2.

Call Forwarding

No Answer

Change Number

Dial this number to change the phone number

to which calls will be forwarded when there

is no answer on Line 1 or Line 2.

Automatic

Callback

Activate

Dial this number to hear the most recent call

you missed and to return the call. If the num-

ber is busy, you can hang up.When the num-

ber is available, your phone will ring. Pick up

your phone and the call will be connected.

Automatic

Callback

Deactivate

Dial this number to de-activate automatic

callback.

Do Not Disturb

Activate

Dial this number to have calls automatically

routed to voice mail.

Do Not Disturb

Deactivate

Dial this number to cancel having calls auto-

matically routed to voice mail.

Calling Number

Delivery

Blocking

Dial this number to block your number from

appearing on the Caller ID of the people you

call. Your calls may appear as “Private” or

“Anonymous”.

Field or Button Description

Basic Configuration

Line Blocking

Deactivate

Dial this number to unblock your telephone

number from appearing on Caller ID.

Call Waiting

Toggle

Dial this number to toggle between call wait-

ing ON and call waiting OFF.

Anonymous Call

Rejection

Activate

Dial this number to have anonymous calls

rejected.

Anonymous Call

Rejection

Deactivate

Dial this number to allow anonymous calls to

go through.

Field or Button Description

Advanced Configuration

The Advanced Configuration section describes the Port

Forwarding, Local Address, and Control Panel menus.

Port Fowarding Menu

Port forwarding enables you to direct incoming traffic to

specific LAN hosts (computers on your network) based on

the protocol and port number. It is used to play Internet

games or provide local services (such as web hosting) for a

LAN group.

The Port Forwarding menu provides the following tabs:

•

Basic

•

Forwarding

Port Forwarding Menu

Advanced Configuration

Basic Tab

Be sure to click the

Apply

button once you have made changes.

Field or Button Description

Enable UPnP

IGD Enables Universal Plug and Play (UPnP)

Internet Gateway Device (IGD) profile to

allow certain Windows applications to setup

the port forwarding rule dynamically when

NAT is enabled on this device.

DMZ

(DeMilitarized

Zone) IP Address

Enter the DMZ IP Address.

Advanced Configuration

Forwarding Tab

Click on the

ADD

button to create additional Port Fowarding rules.

Be sure to click the

Apply

button once you have made changes.

Field or Button Description

Select

Select a box when you want to delete the spe-

cific row.

Protocol

Select TCP (Transmission Control Protocol)

or UDP (User Datagram Protocol).

WAN Port Start

Enter the beginning port range for external

network access.

WAN Port End

Enter the ending port range for external net-

work access.

LAN IP Address

Enter the IP address to host the service.

LAN Port Start

Enter the beginning port range for internal

network access.

LAN Port End

Enter the ending port range for internal net-

work access.

Enabled

Check to enable specific port forwarding.

Advanced Configuration

Local Address Menu

The Local Address menu allows you to configure your Local Area

Network (LAN) connections.

The Local Address menu provides the following tabs:

•

DHCP Server

•

Lease Status

•

Lease Reservation

Local Address Menu

Advanced Configuration

DHCP Server Tab

The DHCP Server tab enables Dynamic Host Configuration

Protocol (DHCP) server functionality on the LAN, allowing the

router to dynamically assign lease IP addresses to clients that

connect to it from the local network.

Field or Button Description

Enable DHCP

Server If selected, the DHCP server on the gateway

assigns IP addresses to the computers and

other hosts on your network if they have

DHCP enabled. By default, the gateway

server is enabled. If there is another DHCP

server running on your network (on another

router), you must disable one of the DHCP

servers.

DHCP Server IP

Address

Enter the default port forwarding LAN Client

IP Address.

DHCP Starting

IP Address

Sets the first IP address assigned by the

DHCP server, in dotted-decimal format. It

must be greater than the IP address value of

the gateway. For example, if the IP address of

the gateway is 192.168.15.1 (default), the

starting IP address must be 192.168.15.2 (or

higher).

DHCP Ending IP

Address Sets the final IP address assigned by the

DHCP server. If the DHCP server runs out of

DHCP addresses, users cannot access

network resources. If this happens, increase

the Ending IP or reduce the Lease Time.

Advanced Configuration

Be sure to click the

Apply

button once you have made changes.

DHCP Lease

Time

Sets the time, in seconds, that a network

computer remains connected to the gateway

using its current assigned IP address. At the

end of this time, the DHCP server renews the

lease or assigns the computer a new IP

address. The default is 3600 seconds (1

hour). The maximum is 999999 seconds

(about 278 hours).

Field or Button Description

Advanced Configuration

Lease Status Tab

The Lease Status tab in the Local Address menu displays the active

DHCP leases since the last reboot.

Be sure to click the

Apply

button once you have made changes.

Field or Button Description

Client Host

Name

Displays the client host name. The Name

field is limited to 20 characters (only 5

appear in display).

MAC Address

Media Access Control (MAC) address.

IP Address

Shows the IP Address for each active lease.

Remaining Lease

Duration

Shows the amount of time, in seconds,

remaining in the lease.

Advanced Configuration

Lease Reservation Tab

This tab allows you to manage the lease reservation so that the same

client receives the same IP address each time.

Be sure to click the

Apply

button once you have made changes.

Field or Button Description

Select

Select this box if you want to delete an estab-

lished lease reservation. Be sure to click the

Delete button once you have selected your

exception to be deleted.

Client Host

Name

Enter the client host name. The Name field is

limited to 20 characters (only 5 appear in dis-

play)

MAC Address

Media Access Control (MAC) address. Enter

the MAC address of the device.

IP Address

Enter the IP address that you want assigned

to the MAC Address.

Enabled

Checking this box enables the lease reserva-

tion.

Advanced Configuration

Control Panel

The Control Panel sections allows you to view/update your

software information.

The Control menu provides the following tabs:

•

Software

•

Certificate

•

System

•

About

Control Panel Menu

Advanced Configuration

Software Tab

The Software tab manages the software on your CPE device. It is

also where you can upgrade device software.

Use the

BROWSE

button to browse your computer for additional

software packages. Once you have located the software

package/update you would like to add to your device, click on the

Upgrade

button.

You should see the available software updates in the “Available

Software Packages” table. If you cannot see the list, click the

View

button.

Select the software you would like to install and click the

Install

button.

If you would like to remove software, select the software package

you would like to remove and click

Uninstall

Certificate Tab

The Certificate tab is where you manage the certificates that are

stored on the device.

Use the

BROWSE

button to locate the certificate file on your

computer, and then click the

IMPORT

button.

Use the

REMOVE

button to remove any selected certificate(s).

Advanced Configuration

System Tab

This tab allows you to manage additional features of your CPE

device.

Be sure to click the

Apply

button once you have made changes.

About Tab

The About Tab will display basic properties of your CPE device

such as: Product Name, Model ID, Hardware Version, Serial

Number and the WiMAX MAC Address.

Field or Button Description

Language Used

in User Interface

Select the desired language for the user

interface. The default language is

English.

Enable WiMAX

Radio Interface

Check this box to enable the WiMAX

Radio Interface.

Enable LED

Checking this box enables the LEDs on

the front of your CPE device.

Auto Refresh

Interval

Enter, in seconds, the interval for status

Auto Refresh. Valid range is 2 seconds -

9999 seconds. The default value is 3 sec-

onds.

Rebootstrap EMS

Check this box to reconnect the device

with the EMS.

Note: Only perform this function under

the supervision of a Customer Support

Representative.

Configuring TCP/IP

This chapter is needed for setup procedures.

All client computers on your network must be configured for

TCP/IP (the protocol that controls communication among

computers). Perform one of:

•

Configuring TCP/IP in Windows 2000

•

Configuring TCP/IP in Windows XP

Note:

Follow the instructions in your Macintosh or UNIX user

manual

Configuring TCP/IP in Windows 2000

1On the Windows Desktop, click Start.

2Select Settings and then Control Panel from the pop-up menus

to display the Control Panel window:

Configuring TCP/IP

Windows Control Panel

3Double-click the Network and Dial-up Connections icon to

display the Network and Dial-up Connections window:

Network and Dial-up Connections

In the steps that follow, a connection number like 1, 2, 3, etc., is a

reference that is displayed on computers with multiple network

interfaces. Computers with only one network interface may only

see the label: Local Area Connection.

Configuring TCP/IP

4Click Local Area Connection number. The value of number

varies from system to system. The Local Area Connection

number Status window is displayed:

Local Area Connection

5Click Properties. Information similar to the following window

is displayed:

Properties

Configuring TCP/IP

6If Internet Protocol (TCP/IP) is in the list of components,

TCP/IP is installed. You can skip to Step 10.

If Internet Protocol (TCP/IP) is not in the list, click Install. The

Select Network Component Type window is displayed:

Select Network Connection Type

7Click Protocol on the Select Network Component Type

window and click Add. The Select Network Protocol window

is displayed:

Select Network Protocol

Note:

You might have to use the scroll bar to locate the Internet

Protocol (TCP/IP) setting.

8Click Internet Protocol (TCP/IP).

9Click OK. The Local Area Connection number Properties

window is re-displayed.

Configuring TCP/IP

Be sure the box next to Internet Protocol (TCP/IP) is checked.

11 Click Properties. The Internet Protocol (TCP/IP) Properties

window is displayed:

Internet Protocol (TCP/IP) Properties

Be sure Obtain IP address automatically and Obtain DNS

server address automatically are selected.

13 Click OK to accept the TCP/IP settings.

14 Click Close to close the Local Area Connection number

Properties window.

15 Click OK

If prompted to restart the computer and click OK again.

Configuring TCP/IP in Windows XP

1On the Windows desktop, click Start to display the Start

window:

Configuring TCP/IP

Windows XP Start Window

2Click Control Panel to display the Control Panel window. The

display varies, depending on your Windows XP view options. If

the display is a Category view as shown below, continue with

Step 3. Otherwise, skip to Step 5

Control Panel

3Click Network and Internet Connections to display the

Network and Internet Connections window:

Configuring TCP/IP

Network and Internet Connections

Click Network Connections. Skip to Step 6.

5If a classic view similar to below is displayed, double-click

Network Connections to display the LAN or High-speed

Internet connections.

Control Panel Classic View

6Right-click the Local Area Connection. If more than one

connection is displayed, be sure to select the one for your

network interface.

Configuring TCP/IP

Network Connections

7Select Properties from the pop-up menu to display the Local

Area Connection Properties window:

Local Area Connection Properties

On the Local Area Connection Properties window, select

Internet Protocol (TCP/IP) if it is not selected.

9Click Properties to display the Internet Protocol (TCP/IP)

Properties window:

Configuring TCP/IP

Internet Protocol (TCP/IP) Properties

10 Be sure Obtain IP address automatically and Obtain DNS

server address automatically are selected.

Click OK to close the TCP/IP Properties window.

Troubleshooting

Power LED is Off

•

Check that the AC power adapter is properly plugged into

the electrical outlet and into the Desktop CPE.

•

Check that the electrical outlet is working.

A Computer Cannot Log On to the CPE

Check that the Ethernet cable is properly connected to the Desktop

CPE unit and the computer.

Cannot Connect to the Internet

•

Check the Desktop CPE connection status from the Web

Interface, refer to the Connection Status section to verify the

connection status.

•

If the Desktop CPE connection is down, and the gateway has

not received an IP for 5 to 10 minutes:

- Re-Run the Setup Wizard.

- If the Setup Wizard does not help, then reset the Desktop

CPE using the reset button.

Additional Troubleshooting Help

•

Contact your service provider for additional help.

Important Safety and Legal Information

Important Safety and Legal

Information

Your Motorola WiMAX Wireless Broadband Gateway is designed

and tested to comply with a number of national and international

standards and guidelines (listed below) regarding human exposure

to RF electromagnetic energy.

This Product complies with the following RF energy

exposure standards and guidelines:

•

United States Federal Communications Commission, Code

of Federal Regulations; 47CFR part 2 sub-part J

•

American National Standards Institute (ANSI)/ Institute of

Electrical and Electronic Engineers (IEEE) C95 1-2005

•

Institute of Electrical and Electronic Engineers (IEEE)

C95.1-1999 Edition

•

International Commission on Non-Ionizing Radiation

Protection (ICNIRP) 1998

•

Ministry of Health (Canada) Safety Code 6. Limits of

Human Exposure to Radio frequency Electromagnetic

Fields in the Frequency Range from 3 kHz to 300 GHz, 1999

•

Australian Communications Authority

Radiocommunications (Electromagnetic Radiation - Human

Exposure) Standard, 2003

•

ANATEL ANNEX to Resolution No. 303 of July 2, 2002

“Regulation of Limitation of Exposure to Electrical,

Important Safety and Legal Information

Magnetic, and Electromagnetic Fields in the Radio

Frequency Range Between 9 kHz and 300 GHz” and

“Attachment to Resolution #303 from July 2, 2002”

RF Exposure Compliance and Guidelines Operating

Instructions

To comply with FCC RF energy exposure requirements, this

Gateway desktop transmitter should be operated at a minimum

separation distance of 20 cm from all persons.

For additional information on exposure requirements or other

training information, visit http://www. motorola.com/rfhealth

FCC Regulatory Information

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any

interference received; including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits

for a Class B digital device pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications.

Important Safety and Legal Information

EU Declaration of Conformity

Important Safety and Legal Information

In compliance with national requirements, a power supply cord

with a cross-sectional area of 0.75mm

minimum for each

individual conductor, will be provided when the product is

submitted for national approval.

Important Safety and Legal Information

Caring for the Environment

The following information is provided to enable regulatory

compliance with the European Union (EU) Directive 2002/96/EC

Waste Electrical and Electronic Equipment (WEEE) when using

Motorola Networks equipment in EU countries.

Disposal of Motorola Equipment in EU

Countries

This product is compliant with the requirements of the European

Union Restriction of Hazardous Substances (EU RoHS) directive.

Please do not dispose of Motorola Networks equipment in landfill

sites.

In the EU, Motorola Networks in conjunction with a recycling part-

ner will ensure that equipment is collected and recycled according

to the requirements of EU environmental law.

Important Safety and Legal Information

Disposal of Motorola Networks

Equipment in Non-EU countries

In non-EU countries, dispose of Motorola Networks equipment in

accordance with national and regional regulations.

CMM Disclosure

The China Management Methods (CMM) Disclosure Table is

intended only to communicate compliance with China

requirements; it is not intended to communicate compliance with

EU RoHS or any other environmental requirements.

CMM Disclosure

CMM Disclosure Information

Copyrights and Trademarks

Notice

While reasonable efforts have been made to assure the accuracy of

this document, Motorola, Inc. assumes no liability resulting from

any inaccuracies or omissions in this document, or from use of the

information obtained herein. The information in this document has

been carefully checked and is believed to be entirely reliable.

However, no responsibility is assumed for inaccuracies or

omissions. Motorola, Inc. reserves the right to make changes to any

products described herein and reserves the right to revise this

document and to make changes from time to time in content hereof

with no obligation to notify any person of revisions or changes.

Motorola, Inc. does not assume any liability arising out of the

application or use of any product, software, or circuit described

herein; neither does it convey license under its patent rights or the

rights of others.

It is possible that this publication may contain references to, or

information about Motorola products (machines and programs),

programming, or services that are not announced in your country.

Such references or information must not be construed to mean that

Motorola intends to announce such Motorola products,

programming, or services in your country.

Copyrights

This instruction manual, and the Motorola products described in

this instruction manual may be, include or describe copyrighted

Copyrights and Trademarks

Motorola material, such as computer programs stored in

semiconductor memories or other media. Laws in the United States

and other countries preserve for Motorola and its licensors certain

exclusive rights for copyrighted material, including the exclusive

right to copy, reproduce in any form, distribute and make derivative

works of the copyrighted material. Accordingly, any copyrighted

material of Motorola and its licensors contained herein or in the

Motorola products described in this instruction manual may not be

copied, reproduced, distributed, merged or modified in any manner

without the express written permission of Motorola. Furthermore,

the purchase of Motorola products shall not be deemed to grant

either directly or by implication, estoppel, or otherwise, any license

under the copyrights, patents or patent applications of Motorola, as

arises by operation of law in the sale of a product.

Usage and Disclosure Restrictions

License Agreements

The software described in this document is the property of

Motorola, Inc and its licensors. It is furnished by express license

agreement only and may be used only in accordance with the terms

of such an agreement.

Copyrighted Materials

Software and documentation are copyrighted materials. Making

unauthorized copies is prohibited by law. No part of the software or

documentation may be reproduced, transmitted, transcribed, stored

in a retrieval system, or translated into any language or computer

language, in any form or by any means, without prior written

permission of Motorola, Inc.

Copyrights and Trademarks

High Risk Materials

Components, units, or third-party products used in the product

described herein are NOT fault-tolerant and are NOT designed,

manufactured, or intended for use as on-line control equipment in

the following hazardous environments requiring fail-safe controls:

the operation of Nuclear Facilities, Aircraft Navigation or Aircraft

Communication Systems, Air Traffic Control, Life Support, or

Weapons Systems (High Risk Activities). Motorola and its

supplier(s) specifically disclaim any expressed or implied warranty

of fitness for such High Risk Activities.

Trademarks

MOTOROLA and the Stylized M Logo are registered in the US

Patent & Trademark Office. All other product or service names are

the property of their respective owners.

Nokia Solutions and Networks CPE25300 Non-line of Sight Wireless Data Link User Manual 285a66

Nokia Solutions and Networks Non-line of Sight Wireless Data Link 285a66

Contents

Manual

Navigation menu

Namespaces

Views

Navigation