Nortek Security and Control 00115 Wireless glass break detector User Manual 235512A GB00Z 1 Iris Instructions indd

Nortek Security & Control LLC Wireless glass break detector 235512A GB00Z 1 Iris Instructions indd

Contents

Instruction2

DETECTOR TESTING1. Follow the system’s instructions to select Test Mode. When instructed, press button on Detector (A) three times.SPECIFICATIONSOperating Temperature: 32° to 120° F (0° to 49° C)Operating Relative Humidity: 5 to 95%, non-condensingOperating Frequency: 908.42 MHzSensor Type: Single microphone, dual-stageGlass Thickness: 1/8” (3.2 mm) to 1/4” (6.4 mm)HELPFUL TIPS• The minimum size for all glass types is 11” x 11” (28 cm x 28 cm) square. Glass must be framed, in a wall of the room or mounted in a barrier of 36” (91 cm) minimum width.• The Detector will not lock onto the Mounting Plate unless both CR123A batteries are installed.• The Detector sends Z-Wave® signals to the system. Z-Wave® is a registered trademark of Sigma Designs Inc. and/or its subsidiaries.WARRANTYLowe’s Utilitech Warranty Here??REGULATORY NOTICEChanges or modifi cations to the device may void FCC compliance.Les modifi cations apportées à l’appareil peuvent annuler la conformité Industrie CanadaPARING INSTRUCTIONS1. Install two Batteries (CC) into the Detector (A). Observe polarity!2. Bring detector within 10 feet of the system. Set system to add glass break detector device, when instructed, press the button on Detector (A) three times to pair with the system.MOUNTING THE DETECTOR1. Choose a location on the ceiling or on an adjacent or opposite wall within 12 feet of the glass to be monitored. Use the Mounting Plate (B) as a template to mark the three mounting holes.2. Drill three 3/16” pilot holes and insert Screw Anchors (BB). Attach Mounting Plate (B) with three Mounting Screws (AA).3. Match alignment marks on Detector (A) and Mounting Plate (B). Turn Detector (A) clockwise to lock onto Mounting Plate (B).ITEM #0000000MODEL #GB00Z-1GLASS BREAK DETECTORQuestions?Call customer service at 1-000-000-0000,5:00 a.m. - 4:30 p.m., PST, Monday-FridayPACKAGE CONTENTSHARDWARE CONTENTSNote: Hardware shown actual size. SAFETY INFORMATIONPlease read and understand this entire manual before attempting to assemble, operate, or install the product. WARNINGDanger of explosion if batteries are installed incorrectly. Replace only with the same or equivalent type recommended by the manufacturer.PREPARATIONBefore beginning installation of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product.Estimated Installation Time: 15 minutes.Tools required for installation (not included):Pencil, Phillips screwdriver, drill, 3/16” drill bitx 1Mounting Platex 3Mounting Screwx 3Screw Anchorx 2CR123A Batteryx 1DetectorAAA CCCCAABBAABAABBCCBBBxxxxx Printed in ChinaPRINTER’S INSTRUCTIONS:INSTR,INSTL,GLASS BREAK,ZW - P/N: 235512 X11 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - FOLDING: Z-FOLD, FINISH WITH LOGO SHOWING - SCALE: 1-1235512 X1113X12213123Utilitech & UT Design® is a registered trademark of LF, LLC. All rights reserved.

Navigation menu