ORION ELECTRIC M2C5A TV Interface Device User Manual 2

ORION ELECTRIC CO., LTD. TV Interface Device Users Manual 2

Contents

Users Manual 2

323Instant Timer Recording (ITR)Load a cassette tape with the eraseprevention tab intact.The VCR will automatically turn on.Set the TV/CATV option to the appropriate position (see page21).12Press SP/EP to select the desired tapespeed SP or EP.The tape counter and “SP” or “EP” willappear on the screen for about 4seconds.4TV - VHF/UHF channelsCATV - CABLE TV channelsThe Instant Timer Recordingfeature provides a simple andconvenient way to make a timedrecording.Press Number keys or VCR CH +/– toselect the channel to be recorded.5NOTE:If you wish to watch the DVD playbackduring the ITR, press DVD to change toDVD mode and perform the DVD play-back (see page 39).Example: Instant Timer Recording for 30 minutes.Press REC on the VCR or while holding REC, press PLAY onthe Remote to begin recording. Press REC on the VCR again tostop recording after 30 minutes. Each additional press of RECwill increase recording time as shown in the chart below, up to amaximum of 6 hours. The ITR and recording time will appear onthe screen for about 4 seconds. And, REC will keep blinking inthe display.Press STOP or turn off the power.“ ” will appear on screen for about 4seconds.To cancel ITRPressoncetwice3 times4 times5 timesNORMAL REC0:301:001:302:003:004:005:006:00NORMAL RECRecording time Press6 times7 times8 times9 times10 timesRecording timeTurn ON the TV and set it to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press VCR to select the VCR mode. (The VCR indicatorwill light.)Preparation:••CH 110CH 125INDEXITR 0 : 3000 : 00 : 00 SP 2C51201AE(30-35) 15/3/03, 11:15 AM32
333Timer recordingPress SET UP MENU. Select theTIMER REC SET option, then pressENTER.Press SET + or – to select the date,then press ENTER.12Press SET + or – to select one of theprogram line, then press ENTER.4Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press VCR to select the VCR mode.Load a cassette tape with the erase prevention tab intact.Press OSD to verify time and date are correct (see page 31).Preparation:•••Timer recording can be programmedon-screen with the remote control.The built-in timer allows automaticunattended recording of up to 8programs within 1 month.Set the start time, end time, channeland tape speed as in step 3.Example: Program a timer recording for the 26th day, channel 125(CATV), 11:00 - 11:30 PM on timer program number 1 (Tape speed: EP).NOTES:If the programmed start time is over thepresent time, the program will be canceledafter pressed ENTER.•••5To enter other programs, repeat step2 through 4.• To return to the normal screen,press SET UP MENU twice.6Press TIMER. The clock symbol ( ) will appear on thedisplay and the VCR stands by for recording. At the sametime, VCR mode will change to DVD mode automatically. Youcan use DVD even if the VCR is in the timer recording mode.If you do not use the DVD, turn the power off.The timer recording will start at 5 seconds before the time youpredetermined.NOTES:If the clock symbol ( ) does not appear on the display in spiteof the pressing of TIMER, the cassette may not have beenloaded yet (see page 26).If the cassette is ejected in spite of the pressing of TIMER , theerase prevention tab of the cassette may have been removed(see page 26).••NOTES:If the clock symbol ( ) blinks whenthe timer recording ended, the TVprogram has not been completelyrecorded because of an insufficienttape supply. In this case, press TIMERto cancel the timer program or pressEJECT to remove the cassette tape.During timer recording standby mode,the VCR mode cannot be selected. Touse the VCR, press TIMER at first,then press VCR to change to VCRmode. After you use the VCR, pressTIMER again to put the VCR into timerrecording standby mode.If you press TIMER during timerrecording, the recording operation willbe interrupted. If you press TIMERagain within the programmed time, therecording operation will start again.After a power failure or disconnectionof the power plug, all programmedrecording settings and time displaywill be lost upon resumption of power.In this case, reset the clock (see pages23-25) and reprogram any timerrecordings.••••Press CANCEL to move cursor backward for correction.To record from external source set the channel to “L”. “L” will appearnext to CH 125 (or 69). 2C51201AE(30-35) 15/3/03, 11:15 AM33
34Timer-recordingTimer recording special caseWeekly (e.g. WKL-TU: each Tuesday) or daily (e.g.MO-SA: Monday to Saturday) timer recordingFollow the procedure of timer recording on the previouspage. At picture 3 press SET + or – repeatedly until thedesired setting appears. Then press ENTER.When you press SET – repeatedly, the indicator atDATE will change as follows, in this case the today isFriday.In case timer programs-overlapDo not overlap timer programs as portions of theconflicting programs will be lost. The first recordingtime has priority over the next recording time as shownin the diagram below.•NOTES:The daily/weekly recording can be made continu-ously until the recording is canceled or the tapereaches the end.During timer recording the automatic rewindingmechanism does not function.••Confirmation / Cancellation of the timerrecording1The current day (Friday) SU-SA (Sunday to Saturday)MO-SA (Monday to Saturday)MO-FR (Monday to Friday)WKL-WE WKL-TH (Weekly Thursday)(Weekly Wednesday)One month laterminus one day8 : 00 11 : 009 : 00 10 : 00Program 1Prog.1Deleted PartsNon Recorded Portion PartsProg.2 Prog.3Program 2Program 3Recording Control SettingsNOTES:If there are other timer record programs remaining,TIMER must be pressed to reactivate the timer,otherwise the remaining timer record programs willbe ignored.You cannot confirm the timer program during timerrecording operation.You can also correct the programmed setting inprogram confirm mode.At step 2 above, press ENTER to enter the programinput mode. Then press ENTER repeatedly until the•••If the timer has been activated, press TIMER todeactivate the timer. The clock symbol ( ) willdisappear. Then press VCR to change to VCRmode.2At picture 1 on theprevious page select the“TIMER REC SET” optionand press ENTER.Then the timer programlist as right will appear onthe screen.To cancel timer program:4Press SET UP MENU repeatedly until the TV-pictureappears.3Press SET + or – toselect the unnecessaryprogram, then pressCANCEL to cancel theprogram.To confirm timer program:item you wish to correctblinks. Then correct the datawith SET + or –.Then press SET UP MENUrepeatedly until the TV-picture appears. 2C51201AE(30-35) 15/3/03, 11:15 AM34
35Stereo recording and playback/Separate Audio Program (SAP)When a MTS STEREO broadcast isreceived, the word “STEREO” will ap-pear on the screen for about 4 secondsand the program can be viewed or re-corded in stereo.The Hi-Fi STEREO recording procedureis the same as for normal recordings.The VHS Hi-Fi audio system permits high fidelity recording of MTSSTEREO TV broadcasts.NOTES:•When playing back a tape that is notrecorded in Hi-Fi stereo mode, theaudio will automatically be monaural.•When listening to a VHS Hi-Fi videotape or MTS broadcast through theVHF/UHF jack (Audio/Video cable notconnected), the sound will bemonaural.Stereo Recording and PlaybackNOTE:When using a CATV system, stereo TV programs may be transmittedover a mono cable channel. In this case the word “STEREO” will notappear and the sound will be in mono.When viewing an MTS STEREO TV program, or playing a prerecordedVHS Hi-Fi STEREO videotape, press A.MONITOR to select how theaudio will be heard through the speakers. Normally set to the Hi-FiSTEREO position, this button can be set to the MONO position if thestereo broadcast or videotape audio is of poor quality. The “R” and “L”positions allow the audio from the Right or Left Hi-Fi channel to be heardover both TV speakers. This button has no effect when viewing a MONOvideotape or TV program. Each time when you press the button, OUTPUTSELECTION display appears on the screen for several seconds. Referto the chart below.Output selectionOUTPUTSELECTIONSTEREOL chR chMONOSOUND HEARD ON BOTHSPEAKERSSTEREOLEFT CHANNEL AUDIORIGHT CHANNEL AUDIOMONOYour VCR is fitted with a SAP broadcast system which enablesyou to switch to a separate audio program when viewing aselected channel.This function applies only when the program is broadcast inmulti-languages through the SAP broadcast system.Separate Audio Program (SAP)Press SET UP MENU. Then press or to select “SAP”.12Then press ENTER to select “ON”.Then press SET UP MENU untilthe menu screen is cleared.When the VCR is turned on or a channel selection is made, makecertain the letters “SAP” appears on the screen for about 4 seconds.This means that the “Separate Audio Program” broadcasting isavailable.Listening to SAPORSTEREOSTEREO SAPSAP 2C51201AE(30-35) 15/3/03, 11:15 AM35
36If you connect the VCR to another VCR or camcorder, you can duplicate a previously recorded tape.Make all connections before turning on the power.Duplicating a video tape/Duplicating a disc material onto a video tapeLoad a blank cassette tape with the erase preven-tion tab intact into the recording VCR.Load a previously recorded tape into the playbackVCR or CAMCORDER.1Press SP/EP to select the desired tape speed SPor EP.It is recommended that you set the speed to theSP mode on the recording VCR for best results.2Press VCR CH + or – to select AUDIO/VIDEO inputposition. “L” will appear in thedisplay.3Press REC on the recording VCR or on the Remote.While holding REC, press PLAY.Then press PAUSE.4Press PLAY button on the playback VCR orCAMCORDER, then press PAUSE button.5Press PAUSE on both the VCRs simultaneously tobegin the duplicating process.6For duplicating a previously recorded tape from acamcorder, follow the camcorder manufacturer’sinstructions. A typical camcorder dubbing hookupis shown above.To AUDIO (L) INTo AUDIO (L) OUTAUDIO/VIDEO cable (supplied)Playback VCRTo VIDEO OUT To AUDIO (R) OUTRecording VCRTo VIDEO IN To AUDIO (R) INAUDIO/VIDEO cable (not supplied)To AUDIO (R) INTo AUDIO (L) INTo VIDEO INRecording VCRTo AV JackPlayback CamcorderConnection with second VCR Connection with CamcorderDuplicating a video tapeYou can record disc material in DVD, Video CD, Audio CD, etc. onto a video tape with this DVD/VCR only.If the DVD disc has a Copy-guard feature, the duplicating is not possible. A symbol mark “ ” willappear on the screen for approx. 4 seconds. See page 39 for more information about the DVD playback.Press DVD to select the DVD mode. (The DVDindicator will light.)1Press PLAY to start the disc playback.2During disc playback, press REC on the VCR orwhile holding REC, press PLAY on the Remote.The duplicating will start.3Duplicating a disc material onto a video tapeLoad a cassette tape with the erase prevention tabintact.Select the tape speed (SP or EP) in the VCR mode.Load a disc you wish to duplicate.Preparation:••••You can set the duplicating time using the ITR-function.At step 3 above press REC repeatedly until the desiredduplicating time appears on the screen (see page 32).•When the scanning mode is set to the progressivemode, you cannot duplicate a disc material onto a videotape. When REC is pressed, the PROGRESSIVEindicator “” on the display window will flash and“PLEASE SET OFF” will appear on the screen.NOTES: 2C51201AE(36-41) 15/3/03, 11:15 AM36
37DiscTitleWhen two or more movies are recorded on a disc,the disc is divided into two or more sections.Each section is called a “TITLE”.ChapterThe titles can be subdivided into many sections.Each section is called a “CHAPTER”.Video CD/Audio CD TrackA Video CD or Audio CD can contain several items.These are assigned to the tracks.Removing Disc from CaseBe sure to hold the edge of disc. Do not touch the surface of the disc.Pick up the disc gently from the case.• Do not scratch the disc.• Do not get dirt on the surface of the disc.• Do not stick a label or adhesive tape on the disc.• Do not drop or bend the disc.Storing Disc• Store the disc in the case to avoid risk of scratches, dirt or damage.• Do not leave disc exposed to direct sunlight or in hot or humid places.Cleaning DiscWipe the disc with a clean, dry cloth from center to edge.• Do not wipe the disc round.• Do not use liquid or aerosol cleaners.CHAPTER 1TITLE1 TITLE2DVD DISCCHAPTER 2 CHAPTER 2 CHAPTER 3CHAPTER 1TRACK 1 TRACK 2 TRACK 3 TRACK 4 TRACK 5CDVideo CD/Audio CDThe following types of discs can be played on this unit.Disc type and logo mark Recorded content Disc sizeDVD VideoVideo CDAudio CDCD-R/CD-RWAudio+VideoAudioCD-DA/JPEG/MP3/WMA file5 inches(12 cm)3 inches(8 cm)5 inches(12 cm)3 inches(8 cm)5 inches(12 cm)3 inches(8 cm)5 inches(12 cm)3 inches(8 cm)RecordableReWritableRegion NumberRegion number (Regional restriction code) is built-in to the unit and DVD video discs.Region number “1” or “ALL” of DVD video discs can be used on this unit.•This unit can play back FUJICOLORCD and Kodak Picture CD formats.•DVD-ROM, SVCD, CVD, Photo CD,etc. cannot be played.•Some CD-R/RWs can not be playedback depending on the recordingconditions.•This unit is to be used exclusively withthe NTSC color system. PAL andSECAM system discs cannot be usedwith this unit.1 2C51201AE(36-41) 15/3/03, 11:15 AM37
38LanguageOSD Language English EnglishFrancaisEspanolOther/Enter/Setup/ReturnPicture ParentalSoundLanguageOSD Language EnglishOther/Enter/Setup/ReturnPicture ParentalSound4Setting setup languageThe setup language can be selected.Press or ENTER and thenpress or to select desiredlanguage (e.g. English), thenpress ENTER.2Press SET UP MENU in the stopmode. The SETUP MENU ofDVD will appear on the screen.NOTE: To make the SETUP screen disappear, press SET UPMENU (or RETURN).If the DVD/VCR does not operateproperly: Static electricity, etc., mayaffect the player's operation. Disconnectthe AC power cord once, then connectit again.3Press or ENTER to select“OSD Language”.Then press or to select“Other”.Language Other/Enter/Setup/ReturnPicture ParentalSound1Press DVD to select the DVDmode. (The DVD indicator willlight.)“No Disc” will appear on thescreen. (If a DVD disc has alreadyloaded, the playback will startautomatically.)Turn ON the TV and set it to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.When using an amplifier, switch on the amplifier.Preparation:••• 2C51201AE(36-41) 15/3/03, 11:15 AM38
394ReadingPlayback procedurePress OPEN/CLOSE or PLAY.The disc tray closes automati-cally.On the screen, changes to“Reading” and then playback willcommence.•A menu screen may appear onthe TV screen, if the disc hasa menu feature. In this case,press , , , orENTER to operate a menufeature.1Press OPEN/CLOSE.The disc tray will open.2Place a disc onto the tray.Hold the disc, position it with theprinted label side up, align it withthe guides, and place it in itsproper position.3Press STOP to end playback.•The DVD/VCR memorizes the stopped point, depending onthe disc. “” appears on the screen for approx. 4 seconds.“” keep blinking in the display until the playback is stoppedcompletely. Press PLAY to resume playback (from the scenepoint).•If you press STOP again (“ ” appears on the screen) or unloadthe disc, the DVD/VCR will clear the stopped point.5Then press OPEN/CLOSE.The disc tray opens.Remove the disc and press POWER.The disc tray closes automatically and DVD/VCR turns off.••NOTES:If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TVscreen according to the type of loaded disc. In this case, check your disc again (see pages 37 and 52).Some discs may take a minute or so to start playback.••••A “Prohibition” symbol may appear at the upper left of the screen. This symbol means either the feature youtried is not available on the disc, or the DVD/VCR can not access the feature at this time. This does not indicatea problem with the DVD/VCR.When you set a single-faced disc label downwards (ie. the wrong way up) and press OPEN/CLOSE or PLAY,“Reading” will appear and remain on the screen for approx. 40 seconds and then it will change to “IncorrectDisc”.Some playback operations of DVDs may be intentionally fixed by software producers. Since this DVD/VCR playsDVDs according to the disc contents the software producers designed, some playback features may not beavailable. Also refer to the instructions supplied with the DVDs.When playing DTS-encoded Audio CDs, excessive noise will be heard from the analog stereo outputs. To avoidpossible damage to the audio system, the consumer should take proper precautions when the analog stereooutputs of the DVD/VCR are connected to an amplification system.Turn ON the TV and set it to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator will light.)Preparation:•• 2C51201AE(36-41) 15/3/03, 11:15 AM39
40Special playbackPress FF during normal playback.Each press of FF will increase the speed of the search (x2), (x4), (x8), (x20).• To resume normal playback, press PLAY.Fast Forward PlaybackPress REW during normal playback.Each press of REW will increase the speed of the search (x2), (x4), (x8), (x20).• To resume normal playback, press PLAY.Review PlaybackPress PAUSE during normalplayback.Still PlaybackTo resume normal playback, pressPLAY.Press PAUSE during still playback.One frame is advanced each timeyou press PAUSE.Frame Advance• To resume normal playback, press PLAY.• To resume the still playback, press PAUSE.Press SLOW during normal playback or still playback.Each press of SLOW will change the speed of the slow x1/2, x1/4,x1/6, x1/7.Slow-motion PlaybackTo resume normal playback, pressPLAY.Locating a chapter or trackThe unit is capable of holding a still videoimage or On screen display image on yourtelevision screen indefinitely. If you leavethe still video image or On screen displayimage displayed on your TV for an ex-tended period of time, you risk permanentdamage to your television screen.Projection televisions are very susceptible.Press SKIP ( ) Forward or SKIP ( ) Reverse during play-back to locate a chapter that you want to watch.Each time you press the button, a chapter or track is skipped.NOTE:Note: There may be a slight delay be-tween pressing the button and thefunction activation. 2C51201AE(36-41) 15/3/03, 11:15 AM40
411NOTES:•You can use the Pause, Slow, Searchor Skip feature in the zoom mode.• In case of the Video-CD playback withPBC, the SEARCH MODE does notwork.This unit will allow you to zoom in on the frame image. You canthen make selections by switching the position of the frame.In the zoom mode press ZOOM repeatedly to return to a 1:1view ( Off).1Press ZOOM during playback.The center part of the image willbe zoomed in.Each press of ZOOM will changethe ZOOM 1 (x 1.3), 2 (x1.5) and 3 (x 2.0).23ZoomingPress / or / to view a different part of the frame.You may move the frame from the center position to UP, DOWN,LEFT or RIGHT direction.Use the title, chapter and time recorded on the disc tolocate the desired point to play back.Press Number keys to change the number.• If you input a wrong number, press CANCEL.• Refer to the package supplied with the disc to check the numbers.1Press SEARCH MODE duringplayback or stop mode.3Locating desired scenePress ENTER.Playback starts.4• When you change the title, playback starts from Chapter 1 ofthe selected title.• Some discs may not work in the above operation.2Press or to select the “Time”, “Title” or “Chapter”.To check the title, chapter and time, press OSD (see page 58).Zooming/Locating desired sceneTurn ON the TV and set it to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator will light.)Preparation:•• 2C51201AE(36-41) 15/3/03, 11:15 AM41
42RepeatPlay Mode OffAll::/Enter/Play ModeChapter:Repeat/Enter/Play ModeNOTES:Some discs may not work with therepeat operation.In A-B repeat mode, subtitles nearpoint A or B may not appear.Repeat playback is not available inmulti-angle scenes.You may not be able to set A-B Re-peat, depending on the scenes of theDVD.A-B repeat does not work with an in-teractive DVD, MP3/WMA/JPEG-CDand Video-CD with PBC.Repeat playbackPress PLAY to start Repeat playback.To resume normal playback, select Repeat “Off”.Repeat playback of Title, Chapter and TrackA-B repeat playback allows you to repeat material between twoselected points.1Press REPEAT A-B duringplayback.The start point is selected.2Press REPEAT A-B again.The end point is selected.Playback starts at the point thatyou selected. Playback stops atthe end point, returns to Point Aautomatically, then starts again.A-B Repeat PlaybackCD•••••2Press ENTER once or twice to select “Chapter” or “Title”.In case of CD, at first press to select “Repeat” and then pressENTER once or twice to select “Track” or “All”.DVDPlay Mode OffRepeat Off/Enter/Play Mode::CD1Press PLAY MODE during playback or stop mode.DVD3Press PLAY MODE again to make the screen disappear.••To resume normal playback press REPEAT A-B again.“Off” appears on the screen.Turn ON the TV and set it to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator willlight.)Preparation:••Off:Repeat/Enter/Play ModeABA 2C51201AE(42-47) 15/3/03, 11:15 AM42
43RepeatPlay Mode:Random:Off/Enter/Play ModeProgram playback/Random playback (CD)1Press PLAY MODE in the stopmode.2Press ENTER repeatedly untilthe Program table as rightappears.3Example: In case you wish toprogram in order of 7, 3, 11:Enter as 7 , 3 , 11.If you input a wrong number,press CANCEL.4Press / or / to select“Program Playback” and pressENTER.The program you selected willbegin to playback in the order set.To return to normal playback, select“Play Mode: Off” at step 2 above.You can arrange the order of tracks on the disc.Program playbackPlay Mode OffRepeat Off/Enter/Play Mode::Turn ON the TV and set it to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator willlight.)Preparation:••1Press PLAY MODE in the stopmode.Random playbackPlay Mode OffRepeat Off/Enter/Play Mode::2Press / to select “Random”.3Press PLAY.Random playback will start.NOTES:•To cancel program playback, select“Clear” at step 3 and press ENTER.•The program is cancelled when youopen the disc tray or turn the power off.•In playing back the Video CD with PBC,you can not set Program playback andRandom playback. 2C51201AE(42-47) 15/3/03, 11:15 AM43
4443MP3/WMA/JPEG playbackThis player can play back the MP3/WMA/JPEG-data which has been recorded on CD-R or CD-RW. To produce the MP3/WMA/JPEG-data, youneed a Windows-PC with CD-ROM drive and aMP3/WMA/JPEG-encoding Software (notsupplied).The Apple-HFS-System can not be played.Limitations on MP3/WMA/JPEG CD playback•MP3/WMA/JPEG CD is the disc that is standardizedby ISO9660, its file name must include 3-digitsextension letters, “mp3”, “wma”, “jpg”.•The directory and file names of the MP3/WMA/JPEG CD must be correspond to the ISOstandardized files.•This unit can read 200 files per disc. If onedirectory has more than 200 files, it reads up to200 files, the remaining files will be omitted.•The unit is able to recognize up to a maximumof 50 directories per disc.•MP3/WMA CDs cannot be used for playbackfor the purpose of recording.•As for multi-session disc, only the first sessioncan be played.•If the CD has both audio tracks and MP3/WMA/JPEG files, only audio tracks are played.•It may take more than one minute for this unit toread MP3/WMA/JPEG files depending on itsstructure.•Music recorded by “Joliet RecordingSpecification” can be played back, the file nameis displayed (within 16 letters) on the screenLong file names will be condensed.•The music files recorded by “Hierarchical FileSystem” (HFS) cannot be played.•The unit can play back baseline and progressiveJPEG files.A file menu screen will appear onthe TV screen.Press / to select folder.Press / or / or Number keys to select the desiredfile.• In case the folder includes more than 15 files, press or to display next file list.Limitations on display•The maximum number for display is 16 letters.Available letters for display are the following:capital or small alphabets of A through Z,numbers of 0 through 9, and _ (under score).•Other letters than those above are replacedin hyphen.Notes on MP3/WMA/JPEG filesTo play back MP3/WMA/JPEG CD in the recordedorder,1. Use MP3/WMA/JPEG software that recordsdata alphabetically or numerically.2. Name each file including two-digit or three-digit number (e.g. “01” “02” or “001” “002”).3. Refrain from making too many sub-folders.CAUTION:•Some MP3/WMA/JPEG CDs can not be playedback depending on the recording conditions.•The CD-R/RW that has no music data or non-MP3/WMA/JPEG files can not be played back.6Press STOP to end playback.• The unit records the stopped point. “” appears on the screen.Press PLAY to resume playback (from the scene point).• If you press STOP again or unload the disc, the unit will clearthe stopped point.1Press OPEN/CLOSE.The disc tray will open.Place a disc on which MP3 or WMAfiles have been recorded onto the tray.2Press OPEN/CLOSE or PLAY. Thedisc tray closes automatically. On theTV-screen, “Reading” will appear.Reading will take as much time asthe number of file.MP3/WMA/JPEG CD informationNOTES:During MP3/WMA/JPEG-Playback, you can not use SEARCH,A-B Repeat functions.You can use Repeat (Track or All), Random functions and Programplayback for MP3/WMA/JPEG CD Playback (see pages 42 and 43).In the case of a CD containing a mixture of MP3, WMA and JPEGfiles, the files are played back by selecting them from the file menu.•••Turn ON the TV and set it to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator willlight.)Preparation:••/0-9/Enter/Play Mode1-/722345JapanCD-RBay BridgeCLOSE MY EYESDIVE TO BLUEHoney89101112flowerLies and Truth-winter fallRainStrawberry6BLUE EYES13Welcome party7Blurry Eyes14ThailandPops--:--/0-9/Enter/Play Mode15-/7216MotherCD-RHold Your LastPops--:--MP3/WMA CD playback1-/72--:--/0-9/Enter/Play Mode2345JapanCD-RBay BridgeCLOSE MY EYESDIVE TO BLUEHoney89101112flowerLies and Truth-winter fallRainStrawberry6BLUE EYES13Welcome party7Blurry Eyes14ThailandPops• When PLAY has been pressed after displaying the file menu,or when the disc tray has been closed after pressing PLAY instep 2, playback begins automatically starting from the firstfile. In this case, if the first file is an MP3/WMA file, only MP3/WMA files are played back in order. If the first file is a JPEGfile, the first JPEG file is played back.Press ENTER.The selected file starts playing back.5 2C51201AE(42-47) 15/3/03, 11:15 AM44
4543A file menu screen will appear onthe TV screen.Press / to select folder.To display a picture menu, pressDVD MENU. (To return to a filemenu, press TITLE.)Press / or / to selectthe desired file.• To display next list, press SKIP/.• When PLAY has been pressed after displaying the file menu,or when the disc tray has been closed after pressing PLAYin step 2, playback begins automatically starting from thefirst file. In this case, if the first file is a JPEG file, the firstJPEG file is played back. If the first file is an MP3/WMA file,only MP3/WMA files are played back in order.1Press OPEN/CLOSE.The disc tray will open.Place a disc on which JPEG fileshave been recorded onto the tray.2Press OPEN/CLOSE or PLAY.The disc tray closes automatically.On the TV-screen, “Reading” willappear. Reading will take as muchtime as the number of file.Turn ON the TV and set it to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicatorwill light.)Preparation:••JPEG CD playbackPress / or / or Numberkeys to select the desired file.6Press STOP to end playback.The file menu appears on the TV screen.If you want to watch the other file, repeat steps 4-5.NOTE:The picture menu is displayed when theFUJICOLOR CD or the Kodak Picture CD areplayed. To display the file menu press TITLE.5Press ENTER.The selected picture appears onthe TV screen.About file menu 2C51201AE(42-47) 15/3/03, 11:15 AM45
46Setting the JPEG IntervalPress SET UP MENU in thestop mode.Press / to select “Picture”,then press or ENTER.Turn ON the TV and set it to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator willlight.)Preparation:••Setting the JPEG IntervalYou can continuously play back all JPEG files automatically./Enter/Setup/ReturnLanguage Picture Parental OtherSoundPress ENTER.Press or to select yourdesired time.123Press or to select “JPEGInterval”.To make SETUP screen disappear, press SET UP MENU.4Off:Plays back one file at a time.5 Seconds:Plays back images in the form of a slide show at 5 secondintervals.10 Seconds:Plays back images in the form of a slide show at 10 secondintervals.15 Seconds:Plays back images in the form of a slide show in 15 secondintervals. 2C51201AE(42-47) 15/3/03, 11:15 AM46
47/Enter/Setup/ReturnLanguage Picture Parental OtherSoundSetting the Select FilesPress SET UP MENU in thestop mode.Press / to select “Picture”,then press or ENTER.Turn ON the TV and set it to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator willlight.)Preparation:••Press ENTER.Press or to select yourdesired file type.123Press or to select “SelectFiles”.To make SETUP screen disappear, press SET UP MENU.4All:Displays all files.Music Only:Displays only MP3/WMA files.Pictures Only:Displays only JPEG files.When playing back a CD containinga mixture of MP3, WMA and JPEGfiles, only MP3/WMA or JPEG filescan be displayed on the file menu. 2C51201AE(42-47) 15/3/03, 11:15 AM47
48Press ZOOM during playback.Enlarged JPEG images are displayed.You can make the images even larger by repeatedly pressingZOOM.ZoomingThis unit will allow you to zoom in on the JPEG image.112Off32In the zoom mode, press ZOOM repeatedly to return to a 1:1view ( Off).Press ANGLE during playback.Images are rotated 90 degreesto the right.Changing anglesYou can display JPEG images rotating at 90 degree intervals.12Press ANGLE repeatedly until the desired angle is selected.Pressing ANGLE four times returns the image to its originalangle.•Images are displayed at the same angle until the disc isremoved.Zooming/Changing angles (JPEG CD)Preparation:•Turn ON the TV and set it to the video input mode.•Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator will light.) 2C51201AE(48-51) 15/3/03, 11:16 AM48
49Marking desired scenes1Press MARKER duringplayback.2Select the blank Marker using/ .Then press ENTER at the desiredscene.•Repeat this procedure to setthe other 2 scenes.3Press MARKER to remove this display.The unit stores the points that youwant to watch again up to 3 points.You can resume playback fromeach scene.Marking the scenes1Press MARKER during playbackor stop mode.Returning to the scenes2Press / to select the Marker1-3.3Press ENTER.Playback starts from the marked scene.NOTES:Some discs may not work with themarking operation.The marking is canceled when youopen the disc tray or turn the power off.Some subtitles recorded around themarker may fail to appear.•••1Press MARKER.To cancel the mark2Press / to select the Marker 1-3.3Press CANCEL.To remove this display, press MARKER.Preparation:•Turn ON the TV and set it to the video input mode.•Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator will light.) 2C51201AE(48-51) 15/3/03, 11:16 AM49
50Changing soundtrack language/Karaoke playback1Press A.MONITOR duringplayback.The current soundtrack languagewill appear.2Press A.MONITOR repeatedlyuntil the desired language isselected.The on-screen display willdisappear after a few seconds.Changing soundtrack languageTurn ON the TV and set it to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator will light.)Preparation:••You can select the language when you play a multilingual disc.In case of VIDEO CD playbackAudio type changes as follows each time you press A.MONITOR.NOTES:The vocal output feature is used duringplayback of Dolby Digital (multi-channel)recorded DVD KARAOKE discs. Thisfeature allows you to turn off vocal audiotracks, or restore them for backgroundaccompaniment.When playing Karaoke, connectappropriate audio equipment such as anamplifier to the DVD/VCR.••LRLRKaraoke playbackWhen playing back a DVD KARAOKE disc, you can turn thevocal on or off.1Press A.MONITOR during DVDKARAOKE disc playback.1/8 Eng Dolby DigitalOff3Press or to select “On” or“Off”.On: The primary vocal is output when it is recorded on thedisc.Off: The primary vocal is not output.2Press or to select Karaokevocal setting. 2C51201AE(48-51) 15/3/03, 11:16 AM50
51Subtitles/Changing angles/Title selection/DVD menuWhen playing back a disc recorded with multi-angle facility, youcan change the angle that you are viewing the scene from.1Press ANGLE during playback.The current angle will appear.2Press ANGLE repeatedly until thedesired angle is selected.Changing AnglesTwo or more titles are recorded on some discs. If the title menuis recorded on the disc, you can select the desired title.Press ENTER or PLAY.The playback of the selected title will start.1Press TITLE during playback.Title menu appears on the screen.•Press TITLE again to resume playback at the scene when youpressed TITLE.2Press / or / to select the desired title.3Title SelectionSome DVDs allow you to select the disc contents using themenu.When you play back these DVDs, you can select the subtitlelanguage and sound-track language,etc. using the DVD menu.Press ENTER.The menu continues to another screen.Repeat steps 2 and 3 to set the item completely.1Press DVD MENU during playback.The DVD menu appears on the screen.•Press DVD MENU again to resume playback atthe scene when you pressed DVD MENU.2Press / or / to select the desired item.3DVD MenuNOTES:If the desired language is not heardafter pressing the SUBTITLE buttonseveral times, the language is notrecorded on the disc.Changing soundtrack or subtitlelanguage is cancelled when you openthe disc tray. The initial default lan-guage or available language will beheard and seen if the disc is playedback again.Depending on the DVD you may beunable to turn on, turn off, or changethe subtitles, even if they are recordedon the disc. While playing the DVD,the subtitle may change while openingor closing the disc tray, or whilechanging the title.In some cases, the subtitle languageis not changed to the selected oneimmediately.Depending on the DVD, you may notbe able to change the angles even ifmulti-angles are recorded on the disc,or you may be unable to select the title,and a “title menu” may simply be calleda “menu” or “title” in the instructionssupplied with the disc.Turn ON the TV and set it to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator will light.)Preparation:••1/9Press SUBTITLE during playbackuntil “OFF” appears.Turning the Subtitles On and OffPress SUBTITLE repeatedly duringplayback until your desired languageappears.The on-screen display will disappearafter a few seconds.You can select the language when playing back a discrecorded with multi-lingual subtitles.Changing the subtitle languageWhen playing back a disc recorded with subtitles, you can turnthe subtitles on or off.Off1/32 Eng••••• 2C51201AE(48-51) 15/3/03, 11:16 AM51
52Parental control1Press SET UP MENU in the stop mode.Press or to select “Parental”.Then press or ENTER.2Press or to select “Parental 8”,then press ENTER until the level youdesire appears (e.g.: 1).3Press once to select “Password ”.4Press ENTER.1234 change to .Parental control settingTurn ON the TV and set to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator will light.)Preparation:••• If you input a wrong number, pressCANCEL.• Be sure to remember this number!Some discs are specified not suitablefor children. Such discs can beprevented from play back with theunit.Level Off : The parental control setting does not function.Level 1 : DVD software for adults cannot be played back.Level 8 : All DVD software can be played back.Select from level 1 to level 8.On a scale of 1-8, “1” is the most restrictive.Then press Number keys to input a 4-digit password (e.g.: 1234).PasswordParental1/Enter/Setup/ReturnLanguage Picture Parental OtherSound5To make SETUP screen disappear, press SET UP MENU.1Select “Password ” (step 1)and press Number keys to input your4-digit password.Then press ENTER.To unlock the Parental Control Setting2If the input password was right, will appear.You can move to “Parental 1”(e.g.) toinput the desired level or to cancelparental control.Cancel the password so as to set the Parental level freely again,NOTES:If each setup (page 46~48, 52~59) hasbeen completed, the unit can alwaysbe worked under the same conditions(especially with DVD discs).Each setup will be retained in thememory if you turn the power off.Depending on the discs, the unit can-not limit playback.Some discs may not be encoded withspecific rating level information thoughits disc jacket says “adult”. For thosediscs, the age restriction will not work.Do not forget the password. If you forgetthe password, contact customer service.•••• 2C51201AE(52-57) 15/3/03, 11:16 AM52
53Temporary disabling of rating level by DVD discIf you wish to cancel the set rating level temporarily, select“Parental Control Level” with or , then press ENTER. Ifthe 4-digits password at step 3 on page 52 has been set, thepassword entering screen will appear as shown in step 4 below.Alternatively, if the password has not been set, playback willcommence. If you don’t know (or have forgotten) the password,select “Cancel Picture”.The setting screen will disappear. Press OPEN/CLOSE toremove the disc.1Load a DVD disc and pressOPEN/CLOSE or PLAY (seepage 39).2If the DVD disc has been designed to temporarily cancel theRating level, the screen which follows the “Reading” screen willchange, depending on which disc is played. If you select “YES”with ENTER key, “Your disc exceeds the parental control level1.”(e.g.) screen will then appear.3Enter the password withNumber buttons (0-9).Then press ENTER.4Playback will commence if the entered password was correct.5NOTE:This temporary cancellation of ratinglevel will be kept until the disc is ejected.When the disc is ejected, the originalrating level will be set againautomatically.Depending on the DVD disc, thedisc may try to temporarily cancelthe rating level that you have set.It is up to you to decide whether tocancel the rating level or not.If you interrupt the entering,press RETURN.Turn ON the TV and set to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator will light.)Preparation:••Your disc exceedsthe parental control level 1.Parental Control LevelCancel Picture/Enter/Return 2C51201AE(52-57) 15/3/03, 11:16 AM53
54Setting menu languagePress or ENTER.Press or to select yourdesired language, then pressENTER.123To make SETUP screen disappear, press SET UP MENU.Other: Other language can be selected (See the Languagecode list on page 61).English, Francais, EspanolThe selected language is the first-priority Menu language.Press or ENTER.Then press or to select“Menu”.4You can select the language of thedisc menu messages of DVDs. Turn ON the TV and set to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator will light.)Preparation:••Press SET UP MENU in the stopmode.Press or to select“Language”./Enter/Setup/ReturnLanguage Picture Parental OtherSoundLanguage Picture Parental OtherSoundMenuSubtitleAudioEnglishAutomaticEnglish/Enter/Setup/Return 2C51201AE(52-57) 15/3/03, 11:16 AM54
55MenuSubtitleAudioEnglishAutomaticEnglish/Enter/Setup/ReturnLanguage Picture Parental OtherSoundIf you want to select another language, enter the language code(see the language code list on page 61).Other:English, Francais, EspanolThe subtitle is displayed with the selected language if it isrecorded on the disc.Setting subtitle languagePress or ENTER.Press or to select yourdesired language, then pressENTER.1Press SET UP MENU in the stopmode.Press or to select“Language”.23To make SETUP screen disappear, press SET UP MENU.4NOTE:If the selected language is not recordedon the disc, the first-priority language isselected.The same subtitle language canalways be selected even if you replacethe disc or turn the power off.Press or ENTER.Then press or to select“Subtitle”.• The unit will automatically select the same language in theAUDIO setting.•When the unit selects the same language as the AUDIO, thesubtitles will not appear during playback.•When you do not use the same language as the AUDIO, thesubtitles will appear during playback.Automatic:Subtitles do not appear.Off:Turn ON the TV and set to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator will light.)Preparation:••/Enter/Setup/ReturnLanguage Picture Parental OtherSound 2C51201AE(52-57) 15/3/03, 11:16 AM55
56Language Picture Parental OtherSoundMenuSubtitleAudioEnglishAutomaticEnglish/Enter/Setup/ReturnSetting audio soundtrack language/Setting surround soundPress or ENTER.Press or to select yourdesired Audio Language, thenpress ENTER.1Press SET UP MENU in the stopmode.Press or to select “Language”.23To make SETUP screen disappear, press SET UP MENU.4NOTES:If the selected language is notrecorded on the disc, the originallanguage will be heard.The “SPATIALIZER N-2-2” is effectiveonly for the sound of disc.The same audio soundtrack languagecan always be selected by your uniteven if you replace the disc or turnthe power off.•English, Francais, Espanol:The language you have selected will play if it is recorded onthe disc.•Other: If you want to select another language,enter the language code (See the Language code list on page60).•Original: The unit will select the first priority language of eachdisc.Press or ENTER.Then press or to select“Audio”.Turn ON the TV and set to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator will light.)Preparation:••/Enter/Setup/ReturnLanguage Picture Parental OtherSoundSetting surround soundThis DVD/VCR equipped with a “SPATIALIZER N-2-2”. It canproduce the effect of being in a cinema or a concert hall.1During disc playback pressA. MONITOR.Press to select “On”.2••To cancel Surround mode:Follow the right steps 1~2, then press to select the “Off” position.Setting audio soundtracklanguage 2C51201AE(52-57) 15/3/03, 11:16 AM56
57/Enter/Setup/ReturnLanguage Picture Parental OtherSoundSetting the aspect ratio of TV screenPress or ENTER.Press or to select yourdesired screen type, then pressENTER.1Press SET UP MENU in the stopmode.Press or to select “Picture”.23To make SETUP screen disappear, press SET UP MENU.4NOTE:If the DVD disc is not formatted in the pan& scan style, it displays 4:3 style.You can select the aspect ratio foryour TV.4:3 Letter boxSelect this mode when connecting to a conventional TV. Whenplaying back a wide screen-DVD disc, it displays the wide picturewith black bands at the top and bottom of screen.4:3 Pan scanIt displays the wide picture on the whole screen with left andright edges automatically cut off.16:9 WideSelect this mode when connecting to a wide-screen TV.A wide screen picture is displayed full size.Press or ENTER, then press or to select “Tv Screen”.You have the following screen sizes to choose from:Turn ON the TV and set to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator will light.)Preparation:•• 2C51201AE(52-57) 15/3/03, 11:16 AM57
58Setting on screen display/Status display of discPress or ENTER to select “On”or “Off”.123To make SETUP screen disappear, press SET UP MENU.4On screen display can be switched onor off when you press the buttons.On: On screen displays appears when you press the anybuttons (factory setting).Off: On screen displays do not appear when you press anybuttons except SET UP MENU, SEARCH MODE, PLAYMODE, MARKER and OSD.Press or ENTER, then press or to select “Display”.00:34:56 01:12:33Each press of OSD, the status display of the disc will appear on thescreen and change as follows.DVDAUDIOCDStatus display of discTurn ON the TV and set to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator will light.)Preparation:••Press SET UP MENU in the stopmode.Press or to select “Picture”.00:34:56 01:12:331/9Title 1/991/81/32Chapter 1/999Eng Dolby DigitalEngVIDEOCD34:56 71:33Track 11/99To make status display disappear, press OSD again./Enter/Setup/ReturnLanguage Picture Parental OtherSoundWhen you playback the CD disc, the status display will appear onthe screen and continue displaying. 2C51201AE(58-Back) 15/3/03, 11:16 AM58
59/Enter/Setup/ReturnLanguage Picture Parental OtherSoundDRCMaxStdMin/Enter/Setup/ReturnLanguage Picture Parental OtherSoundStdDynamic Range ControlPress or ENTER, thenpress or to selectdesired setting.1Press SET UP MENU in the stop mode.Press or to select“Sound”.23DRC (Dynamic Range Control) enablesyou to control the dynamic range soas to achieve a suitable sound foryour equipment.Max: Full dynamic range is increased.Std: Full dynamic range is maintained.Min: Dynamic range is reduced.Press or ENTER toselect “DRC”.NOTES:•This function works only during playbackof Dolby Digital recorded discs.•The level of Dynamic Range Reduction maydiffer depending on DVD video disc.Turn ON the TV and set to the video input mode.Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator will light.)Preparation:•• 2C51201AE(58-Back) 15/3/03, 11:16 AM59
60Progressive scanThe unit supports the Progressivescanning system as well as theconventional interlaced scanningsystem. If your television or monitorequipped with component jackssupport the progressive video input,you can enjoy a high quality pictureby making the Progressive scanningmodo active.•Connect to a TV equipped with component jacks.•Turn On the TV and set it to the corresponding video input mode.•Set the S-VIDEO /COMPONENT video selector switch on therear panel to COMPONENT position.•Make sure TV/VCR/DVD switch has been slided to VCR/DVD.Then press DVD to select the DVD mode. (The DVD indicator will light.)Preparation:1Press PROGRESSIVE in the stop mode. The PROGRESSIVEindicator “ ” on the display window is lit.•The unit recognizes the picture type (film or video source) ofthe current disc according th the disc information.2Press PLAY to start playback.•To make the progressive scanning mode inactive, pressPROGRESSIVE in the stop mode. The PROGRESSIVEindicator “ ” on the display window is not lit.About SCANNING MODETo display video on the television (monitor) screen, the conventionalscanning method is called “Interlaced scanning.” With this method,only half of the horizontal lines are displayed at a time. So two fieldscomplete a single picture (frame); i.e., the first field, containing allthe odd-numbered lines, is displayed followed by the second field,containing all the even-numbered lines.On the other hand, the Progressive scanning system scans allhorizontal lines at a time, so you can double the number of picturescompared with the interlaced scanning, resulting in flicker-free,high-density picture.To enjoy the progressive scanned video, a monitor (or TV orprojector) to be connected to the unit must have the Progressiveinputs.Depending on the material source format, DVD VIDEO discs can beclassified into two types; film source and video source (note thatsome DVD VIDEO discs contain both film source and videosource). Film sources are recorded as 24-frame-per-secondinformation, while (NTSC) video sources are recorded as 30-frame-per second (60-field-per-second interlaced) information.When the unit plays back a film source material, uninterlacedprogressive output signals are created using the original information.When a video source material is played back, the unit interleaveslines between the interlaced lines on each to create the interpolatedpicture and putputs as the progressive signal.S-VIDEO/COMPONENTVideo selector switchNOTES:•Some discs may not be played back with the progressive scanning mode correctly because of the disccharacteristics or recording condition.•There are some progressive TV and High-Definition TV sets that are not fully compatible with the unit, resultingin the unnatural picture when playing back a DVD VIDEO disc in the Progressive scanning mode. In such a case,use the Interlaced scanning mode. To check the compatibility of your TV set, contact your local JVC customerservice center.•You cannot make the progressive scanning mode active in following cases.– The unit is in the VCR mode.– The disc is played back in the DVD mode.– The S-VIDEO/PROGRESSIVE video selector swich is set to S-VIDEO positon. 2C51201AE(58-Back) 15/3/03, 11:16 AM60
61Language code listEnter the appropriate code number for the initial settings “Audio”, “Subtitle” and/or “Menu” (see pages 54-56).Abkhazian 1112 Fiji 1620 Lingala 2224 Singhalese 2919Afar 1111 Finnish 1619 Lithuanian 2230 Slovak 2921Afrikaans 1116 French 1628 Macedonian 2321 Slovenian 2922Albanian 2927 Frisian 1635 Malagasy 2317 Somali 2925Amharic 1123 Galician 1722 Malay 2329 Spanish 1529Arabic 1128 Georgian 2111 Malayalam 2322 Sundanese 2931Armenian 1835 German 1415 Maltese 2330 Swahili 2933Assamese 1129 Greek 1522 Maori 2319 Swedish 2932Aymara 1135 Greenlandic 2122 Marathi 2328 Tagalog 3022Azerbaijani 1136 Guarani 1724 Moldavian 2325 Tajik 3017Bashkir 1211 Gujarati 1731 Mongolian 2324 Tamil 3011Basque 1531 Hausa 1811 Nauru 2411 Tatar 3030Bengali; Bangla 1224 Hebrew 1933 Nepali 2415 Telugu 3015Bhutani 1436 Hindi 1819 Norwegian 2425 Thai 3018Bihari 1218 Hungarian 1831 Oriya 2528 Tibetan 1225Breton 1228 Icelandic 1929 Panjabi 2611 Tigrinya 3019Bulgarian 1217 Indonesian 1924 Pashto, Pushto 2629 Tonga 3025Burmese 2335 Interlingua 1911 Persian 1611 Turkish 3028Byelorussian 1215 Irish 1711 Polish 2622 Turkmen 3021Cambodian 2123 Italian 1930 Portuguese 2630 Twi 3033Catalan 1311 Japanese 2011 Quechua 2731 Ukrainian 3121Chinese 3618 Javanese 2033 Rhaeto-Romance 2823 Urdu 3128Corsican 1325 Kannada 2124 Romanian 2825 Uzbek 3136Croatian 1828 Kashmiri 2129 Russian 2831 Vietnamese 3219Czech 1329 Kazakh 2121 Samoan 2923 Volapük 3225Danish 1411 Kirghiz 2135 Sanskrit 2911 Welsh 1335Dutch 2422 Korean 2125 Scots Gaelic 1714 Wolof 3325English 1524 Kurdish 2131 Serbian 2928 Xhosa 3418Esperanto 1525 Laothian 2225 Serbo-Croatian 2918 Yiddish 2019Estonian 1530 Latin 2211 Shona 2924 Yoruba 3525Faroese 1625 Latvian, Lettish 2232 Sindhi 2914 Zulu 3631Language Name Code Language Name Code Language Name CodeLanguage Name Code 2C51201AE(58-Back) 15/3/03, 11:16 AM61
62SYMPTOMS POSSIBLE SOLUTIONS•Make sure the power cord is plugged in.•Try another AC outlet.•Power is off, check fuse or circuit breaker.•Unplug unit, then plug it back in.•Select the DVD or VCR mode before operating.•Make sure TV/VCR/DVD switch has been slided to VCR/DVD.DVD/VCR does not operate.Problems and troubleshootingUse the following check list for troubleshooting when you have problems with your unit. Consult your localdealer or service outlet if problems persist.Be sure all connections are properly made when using with other units.DVD/VCRPAGE5––520,3820,38The remote control does notfunction.• Aim the remote control at the remote sensor.• Operate within Approx. 5 Meters or reduce the light in the room.• Clear the path of the beam.• The batteries are weak. Replace the batteries.• Check the batteries are inserted correctly.• Check the frequency code is set correctly.11DVDNo picture.• Antenna connection is not correct or antenna cable is disconnected.• The video channel is not in the correct position or the TV is notset to the video channel 3 or 4.• Check the unit is connected correctly.• The video input selector of the TV is not set to VIDEO. Set toVIDEO (or equivalent).• Channel is set to the external mode.No sound.• Check the unit is connected correctly.• Check the input selector of the amplifier is set properly.• The unit is in the Special playback mode.14~172014~19––14~19–28,40•Select proper language in the menu options.Display is not shown in yourlanguage. 38Playback doesn’t start. • No disc is inserted.• The disc may be dirty. Clean up the disc.• The unit cannot play DVD-ROMs, etc.393737No CATV reception •Check all CATV connections.•Station or CATV system problems, try another station. 16,17Noise bars on screen.• Tracking adjustment beyond range of automatic tracking circuit.Try Manual tracking adjustment.• Video heads are dirty.• The tape is worn or damaged.VCR•The erase prevention tab of the video cassette is broken off.•The unit is in the external input mode.TV recording does not work. 26,30Timer recording does not work. • The time is not set correctly.• The recording start/end time is not set correctly.• The TIMER has not been pressed ( is not lit).23,2533332863–No POWER but a picture appearson the TV screen.•During the Auto Clock operation, a video signal can be put out.Please set the clock with Manual clock setting or wait until theAuto Clock operation completed.25The DVD-keys on the RCU of theother JVC RECEIVER/TV is noteffective.•This is not a defect. Since this unit is combined type of DVDand VCR, the remote code of DVD is individual. 12,13 2C51201AE(58-Back) 15/3/03, 11:16 AM62
63No subtitle • Some discs have no subtitles.• Subtitles are cleared. Press SUBTITLE.Angle cannot be changed. • Multi-angles are not recorded on the DVD disc.• The function is prohibited with the unit or the disc. appears on the screen.515139SYMPTOMS POSSIBLE SOLUTIONS PAGEProblems and troubleshooting/Video head cleaningNOTES: •DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THEREAR COVER.•Video heads may eventually wear out and should be replaced when they fail to produce clear pictures.•To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.Video head cleaningVideo head cloggingThe video heads are the means by which the DVD/VCR readsthe picture from the tape during playback. In the unlikely eventthat the heads become dirty enough to be clogged, no picturewill be played back. This can easily be determined if, duringplayback of a known good tape, there is good sound, but nopicture (picture is extremely snowy). If this is the case, havethe DVD/VCR checked by qualified service personnel. Good Picture Snowy PictureAuto Clock SettingNotes for Canadian customers regarding the clock feature of your DVD/VCR.The XDS signals are carried only by certain broadcast television stations (for example, the signal is carried bymost Public Broadcasting Service stations). You must be able to receive a station carrying the XDS signal touse the Auto Clock Setting to set your DVD/VCR’s internal clock. If you live in an area that does not broadcastXDS signals, you must set the clock manually. Please see page 25 for instructions on how to manually set yourDVD/VCR’s clock.Special note for residents of Newfoundland:The Auto Clock Setting cannot be used to set the DVD/VCR’s internal clock to Newfoundland time. The timezone command does not include a setting for the Newfoundland time zone. Trying to use the Auto Clock Settingin the Newfoundland time zone could result in an incorrect time setting or no setting at all. Please set your DVD/VCR’s clock using the Manual Clock Setting.NotesNo 4:3 (16:9) picture • The setup does not match your TV.No on-screen display • Select Display On.5758No surround sound • The setup does not match your stereo system.The unit or remote operation keyis not functioning. • Turn off the unit and unplug the AC power cord for severalminutes, then replug it.19Playback does not start when thetitle is selected. • Check the Parental setup.Audio soundtrack and/or subtitlelanguage is not changed when youplay back a DVD. • Multilingual language is not recorded on the DVD disc.–5255,56Stopping playback, search, slow-motion play, repeat play, or programplay, etc. cannot be performed. • Some discs may not do some of the functions. –No picture, or the screen is blurredor divided into two parts.• The S-VIDEO/COMPONENT selecter is not set correctly.• The progressive scanning mode is active through the unit isconnected to a TV via the VIDEO OUT jack.1860 2C51201AE(58-Back) 15/3/03, 11:16 AM63
64GENERALPower supply:Power consumption:Weight:Dimensions:Inputs/Outputs:Video:Audio:Antenna:Hi-Fi Frequency Response:Hi-Fi Dynamic Range:VCR sectionVideo Head:Audio Track:Tuner:RF Channel Output:F.FWD/REW Time:DVD sectionSignal system:Applicable disc:Audio characteristics:Frequency response:S/N Ratio:Harmonic distortion:Wow and flutter:Dynamic range:Output:Pickup:ACCESSORIES:AC 120V 60HzOperation: 18WStand by: 2W7.9lbs (3.6 kg)Width : 16-15/16 inches (430 mm)Height: 3-7/8 inches (99 mm)Depth : 9-13/16 inches (249 mm)In: 1Vp-p/75 ohmOut: 1Vp-p/75 ohmIn: –8 dBm/50k ohmOut: –8 dBm/1k ohmUHF/VHF IN/OUT: 75 ohm coaxial20Hz to 20,000HzMore than 90dB4 Rotary HeadsHi-Fi Sound - 2 Tracks / MONO Sound - 1 Track181 Channel Freq. SynthesizedVHF 2-13UHF 14-69CATV 14-36 (A)-(W)37-59 (AA)-(WW)60-85 (AAA)-(ZZZ)86-94 (86)-(94)95-99 (A-5)-(A-1)100-125 (100)-(125)01 (5A)Channel 3 or 4, SwitchableApprox. 1 minute 48 seconds (with T-120 Cassette Tape) (at+25°C)NTSCDVD (12cm, 8cm), CD (12cm, 8cm)DVD: 4Hz - 22kHzCD: 4Hz - 20kHz90dB0.02%Less than 0.01% WrmsMore than 90dBVideo : (RCA) 1 Vp-p/75 ohmAudio : (RCA) –8 dBm/1k ohmDigital Audio : 0.5Vp-p 75 ohmCD : Wavelength: 775 - 805 nmMaximum output power: 0.5 mWDVD : Wavelength: 640 - 660 nmMaximum output power: 1.0 mWRemote control x 1Batteries (2 x AA)75 ohm Coaxial Cable x 1AUDIO/VIDEO Cable x 1Specifications 2C51201AE(58-Back) 15/3/03, 11:16 AM64
65HOW TO LOCATE YOUR JVC SERVICE CENTER— JVCTOLL FREE: 1-800-537-5722http://www.jvc.comDear Customer,In order to receive the most satisfaction from your purchase, please read the instruction booklet before operatingthe unit. In the event that repair is necessary, or for the address nearest your location within the ContinentalUnited States, please call 1-800-537-5722 for your nearest authorized servicer or visit our website atwww.JVC.com. Remember to retain your Bill of Sale for Warranty Service.DIVISION OF JVC AMERICAS CORP.Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineeringand production of the wide array of JVC products, service is the key to maintaining the high level performancefor which JVC is world famous. The JVC service and engineering organization stands behind our products.NATIONAL HEADQUARTERSJVC SERVICE & ENGINEERING COMPANY OF AMERICADIVISION OF JVC AMERICAS CORP.10 New Maple AvenuePine Brook, NJ 07058-9641JVC SERVICE & ENGINEERINGCOMPANY OF AMERICACAUTIONTo prevent electrical shock, do not open the cabinet.There are no user serviceable parts inside.Please refer to qualified service personnel for repairs.ACCESSORIESTo purchase accessories for your JVC product, youmay contact your local JVC Dealer.From the 48 Continental United States call toll free:1-800-882-2345 or on the web at www.JVC.comDon’t service the product yourself.FOR SERVICING (Only in U.S.A.) 2C51201AE(58-Back) 15/3/03, 11:16 AM65
66LIMITED WARRANTY CONSUMER VIDEO 1-90JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THEORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from thedate of original retail purchase for the period as shown below. (“The Warranty Period”)THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA ANDIN COMMONWEALTH OF PUERTO RICO.WHAT WE WILL DO:If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Suchrepair and replacement services shall be rendered by JVC during normal business hours at JVC authorized servicecenters. Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and partsthereof may be brought to a JVC authorized service center on a carry-in basis except for Television sets having a screensize 25 inches and above which are covered on an in-home basis.WHAT YOU MUST DO FOR WARRANTY SERVICE:Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorizedservice center, please call toll free: (800) 537-5722.If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copyof your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name andlocation of which will be given to you by the toll-free number.If you have any questions concerning your JVC Product, please contact our Customer Relations Department.WHAT IS NOT COVERED:This limited warranty provided by JVC does not cover:1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faultyinstallation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized byJVC to render such service, or if affixed to any attachment not provided with the products, or if the model or serialnumber has been altered, tampered with, defaced or removed;2. Initial installation and installation and removal for repair;3. Operational adjustments covered in the Owner’s Manual, normal maintenance, video and audio head cleaning;4. Damage that occurs in shipment, due to act of God, and cosmetic damage;5. Signal reception problems and failures due to line power surge;6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;7. Accessories;8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);There are no other express warranties except as listed above.THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY,IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHERDAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGETO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANYBREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OFMERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIODSET FORTH ABOVE.Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an impliedwarranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights andyou may also have other rights which vary from state to state.JVC COMPANY OF AMERICA 1700 Valley RoadDIVISION OF JVC AMERICAS CORP. Wayne, New Jersey 07470WARRANTY (Only in U.S.A.)REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FORDETAILS OF REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCTWARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT.For customer use:Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of thecabinet. Retain this information for future reference.Model No.: Serial No.:Purchase date: Name of dealer: 2C51201AE(58-Back) 15/3/03, 11:16 AM66
67MEMO 2C51201AE(58-Back) 15/3/03, 11:16 AM67
68J2C51201A03/04 UVICTOR COMPANY OF JAPAN, LIMITEDPrinted in Thailand0403-AH-OR-OR 2C51201AE(58-Back) 17/3/03, 3:55 PM68

Navigation menu