ORION ELECTRIC M2C5A TV Interface Device User Manual 2

ORION ELECTRIC CO., LTD. TV Interface Device Users Manual 2

Contents

Users Manual 2

32
3
Instant Timer Recording (ITR)
Load a cassette tape with the erase
prevention tab intact.
The VCR will automatically turn on.
Set the TV/CATV option to the appropriate position (see page
21).
1
2Press SP/EP to select the desired tape
speed SP or EP.
The tape counter and “SP” or “EP” will
appear on the screen for about 4
seconds.
4
TV - VHF/UHF channels
CATV - CABLE TV channels
The Instant Timer Recording
feature provides a simple and
convenient way to make a timed
recording.
Press Number keys or VCR CH +/– to
select the channel to be recorded.
5
NOTE:
If you wish to watch the DVD playback
during the ITR, press DVD to change to
DVD mode and perform the DVD play-
back (see page 39).
Example: Instant Timer Recording for 30 minutes.
Press REC on the VCR or while holding REC, press PLAY on
the Remote to begin recording. Press REC on the VCR again to
stop recording after 30 minutes. Each additional press of REC
will increase recording time as shown in the chart below, up to a
maximum of 6 hours. The ITR and recording time will appear on
the screen for about 4 seconds. And, REC will keep blinking in
the display.
Press STOP or turn off the power.
“ ” will appear on screen for about 4
seconds.
To cancel ITR
Press
once
twice
3 times
4 times
5 times
NORMAL REC
0:30
1:00
1:30
2:00
3:00
4:00
5:00
6:00
NORMAL REC
Recording time Press
6 times
7 times
8 times
9 times
10 times
Recording time
Turn ON the TV and set it to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press VCR to select the VCR mode. (The VCR indicator
will light.)
Preparation:
•
•
CH 110
CH 125
INDEX
ITR 0 : 30
00 : 00 : 00 SP
2C51201AE(30-35) 15/3/03, 11:15 AM32
33
3
Timer recording
Press SET UP MENU. Select the
TIMER REC SET option, then press
ENTER.
Press SET + or – to select the date,
then press ENTER.
1
2Press SET + or – to select one of the
program line, then press ENTER.
4
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press VCR to select the VCR mode.
Load a cassette tape with the erase prevention tab intact.
Press OSD to verify time and date are correct (see page 31).
Preparation:
•
•
•
Timer recording can be programmed
on-screen with the remote control.
The built-in timer allows automatic
unattended recording of up to 8
programs within 1 month.
Set the start time, end time, channel
and tape speed as in step 3.
Example: Program a timer recording for the 26th day, channel 125
(CATV), 11:00 - 11:30 PM on timer program number 1 (Tape speed: EP).
NOTES:
If the programmed start time is over the
present time, the program will be canceled
after pressed ENTER.
•
•
•
5To enter other programs, repeat step
2 through 4.
• To return to the normal screen,
press SET UP MENU twice.
6Press TIMER. The clock symbol ( ) will appear on the
display and the VCR stands by for recording. At the same
time, VCR mode will change to DVD mode automatically. You
can use DVD even if the VCR is in the timer recording mode.
If you do not use the DVD, turn the power off.
The timer recording will start at 5 seconds before the time you
predetermined.
NOTES:
If the clock symbol ( ) does not appear on the display in spite
of the pressing of TIMER, the cassette may not have been
loaded yet (see page 26).
If the cassette is ejected in spite of the pressing of TIMER , the
erase prevention tab of the cassette may have been removed
(see page 26).
•
•
NOTES:
If the clock symbol ( ) blinks when
the timer recording ended, the TV
program has not been completely
recorded because of an insufficient
tape supply. In this case, press TIMER
to cancel the timer program or press
EJECT to remove the cassette tape.
During timer recording standby mode,
the VCR mode cannot be selected. To
use the VCR, press TIMER at first,
then press VCR to change to VCR
mode. After you use the VCR, press
TIMER again to put the VCR into timer
recording standby mode.
If you press TIMER during timer
recording, the recording operation will
be interrupted. If you press TIMER
again within the programmed time, the
recording operation will start again.
After a power failure or disconnection
of the power plug, all programmed
recording settings and time display
will be lost upon resumption of power.
In this case, reset the clock (see pages
23-25) and reprogram any timer
recordings.
•
•
•
•
Press CANCEL to move cursor backward for correction.
To record from external source set the channel to “L”. “L” will appear
next to CH 125 (or 69).
2C51201AE(30-35) 15/3/03, 11:15 AM33
34
Timer-recording
Timer recording special case
Weekly (e.g. WKL-TU: each Tuesday) or daily (e.g.
MO-SA: Monday to Saturday) timer recording
Follow the procedure of timer recording on the previous
page. At picture 3 press SET + or – repeatedly until the
desired setting appears. Then press ENTER.
When you press SET – repeatedly, the indicator at
DATE will change as follows, in this case the today is
Friday.
In case timer programs-overlap
Do not overlap timer programs as portions of the
conflicting programs will be lost. The first recording
time has priority over the next recording time as shown
in the diagram below.
•
NOTES:
The daily/weekly recording can be made continu-
ously until the recording is canceled or the tape
reaches the end.
During timer recording the automatic rewinding
mechanism does not function.
•
•
Confirmation / Cancellation of the timer
recording
1
The current day (Friday) SU-SA (Sunday to Saturday)
MO-SA (Monday to Saturday)
MO-FR (Monday to Friday)
WKL-WE WKL-TH (Weekly Thursday)
(Weekly Wednesday)
One month later
minus one day
8 : 00 11 : 00
9 : 00 10 : 00
Program 1
Prog.1
Deleted Parts
Non Recorded Portion Parts
Prog.2 Prog.3
Program 2
Program 3
Recording
Control Settings
NOTES:
If there are other timer record programs remaining,
TIMER must be pressed to reactivate the timer,
otherwise the remaining timer record programs will
be ignored.
You cannot confirm the timer program during timer
recording operation.
You can also correct the programmed setting in
program confirm mode.
At step 2 above, press ENTER to enter the program
input mode. Then press ENTER repeatedly until the
•
•
•
If the timer has been activated, press TIMER to
deactivate the timer. The clock symbol ( ) will
disappear. Then press VCR to change to VCR
mode.
2At picture 1 on the
previous page select the
“TIMER REC SET” option
and press ENTER.
Then the timer program
list as right will appear on
the screen.
To cancel timer program:
4Press SET UP MENU repeatedly until the TV-picture
appears.
3Press SET + or – to
select the unnecessary
program, then press
CANCEL to cancel the
program.
To confirm timer program:
item you wish to correct
blinks. Then correct the data
with SET + or –.
Then press SET UP MENU
repeatedly until the TV-
picture appears.
2C51201AE(30-35) 15/3/03, 11:15 AM34
35
Stereo recording and playback/Separate Audio Program (SAP)
When a MTS STEREO broadcast is
received, the word “STEREO” will ap-
pear
on the screen for about 4 seconds
and the program can be viewed or re-
corded in stereo.
The Hi-Fi STEREO recording procedure
is the same as for normal recordings.
The VHS Hi-Fi audio system permits high fidelity recording of MTS
STEREO TV broadcasts.
NOTES:
•When playing back a tape that is not
recorded in Hi-Fi stereo mode, the
audio will automatically be monaural.
•When listening to a VHS Hi-Fi video
tape or MTS broadcast through the
VHF/UHF jack (Audio/Video cable not
connected), the sound will be
monaural.
Stereo Recording and Playback
NOTE:
When using a CATV system, stereo TV programs may be transmitted
over a mono cable channel. In this case the word “STEREO” will not
appear and the sound will be in mono.
When viewing an MTS STEREO TV program, or playing a prerecorded
VHS Hi-Fi STEREO videotape, press A.MONITOR to select how the
audio will be heard through the speakers. Normally set to the Hi-Fi
STEREO position, this button can be set to the MONO position if the
stereo broadcast or videotape audio is of poor quality. The “R” and “L”
positions allow the audio from the Right or Left Hi-Fi channel to be heard
over both TV speakers. This button has no effect when viewing a MONO
videotape or TV program. Each time when you press the button, OUTPUT
SELECTION display appears on the screen for several seconds. Refer
to the chart below.
Output selection
OUTPUT
SELECTION
STEREO
L ch
R ch
MONO
SOUND HEARD ON BOTH
SPEAKERS
STEREO
LEFT CHANNEL AUDIO
RIGHT CHANNEL AUDIO
MONO
Your VCR is fitted with a SAP broadcast system which enables
you to switch to a separate audio program when viewing a
selected channel.
This function applies only when the program is broadcast in
multi-languages through the SAP broadcast system.
Separate Audio Program (SAP)
Press SET UP MENU. Then press or to select “SAP”.
1
2Then press ENTER
to select “ON”.
Then press SET UP MENU until
the menu screen is cleared.
When the VCR is turned on or a channel selection is made, make
certain the letters “SAP” appears on the screen for about 4 seconds.
This means that the “Separate Audio Program” broadcasting is
available.
Listening to SAP
OR
STEREO
STEREO SAP
SAP
2C51201AE(30-35) 15/3/03, 11:15 AM35
36
If you connect the VCR to another VCR or camcorder, you can duplicate a previously recorded tape.
Make all connections before turning on the power.
Duplicating a video tape/Duplicating a disc material onto a video tape
Load a blank cassette tape with the erase preven-
tion tab intact into the recording VCR.
Load a previously recorded tape into the playback
VCR or CAMCORDER.
1
Press SP/EP to select the desired tape speed SP
or EP.
It is recommended that you set the speed to the
SP mode on the recording VCR for best results.
2
Press VCR CH + or – to select AUDIO/VIDEO input
position. “L” will appear in the
display.
3
Press REC on the recording VCR or on the Remote.
While holding REC, press PLAY.
Then press PAUSE.
4
Press PLAY button on the playback VCR or
CAMCORDER, then press PAUSE button.
5
Press PAUSE on both the VCRs simultaneously to
begin the duplicating process.
6
For duplicating a previously recorded tape from a
camcorder, follow the camcorder manufacturer’s
instructions. A typical camcorder dubbing hookup
is shown above.
To AUDIO (L) IN
To AUDIO (L) OUT
AUDIO/VIDEO cable (supplied)
Playback VCR
To VIDEO OUT To AUDIO (R) OUT
Recording VCR
To VIDEO IN To AUDIO (R) IN
AUDIO/VIDEO cable (not supplied)
To AUDIO (R) IN
To AUDIO (L) IN
To VIDEO IN
Recording VCR
To AV Jack
Playback Camcorder
Connection with second VCR Connection with Camcorder
Duplicating a video tape
You can record disc material in DVD, Video CD, Audio CD, etc. onto a video tape with this DVD/VCR only.
If the DVD disc has a Copy-guard feature, the duplicating is not possible. A symbol mark “ ” will
appear on the screen for approx. 4 seconds. See page 39 for more information about the DVD playback.
Press DVD to select the DVD mode. (The DVD
indicator will light.)
1
Press PLAY to start the disc playback.
2
During disc playback, press REC on the VCR or
while holding REC, press PLAY on the Remote.
The duplicating will start.
3
Duplicating a disc material onto a video tape
Load a cassette tape with the erase prevention tab
intact.
Select the tape speed (SP or EP) in the VCR mode.
Load a disc you wish to duplicate.
Preparation:
•
•
•
•You can set the duplicating time using the ITR-function.
At step 3 above press REC repeatedly until the desired
duplicating time appears on the screen (see page 32).
•When the scanning mode is set to the progressive
mode, you cannot duplicate a disc material onto a video
tape. When REC is pressed, the PROGRESSIVE
indicator “” on the display window will flash and
“PLEASE SET OFF” will appear on the screen.
NOTES:
2C51201AE(36-41) 15/3/03, 11:15 AM36
37
Disc
Title
When two or more movies are recorded on a disc,
the disc is divided into two or more sections.
Each section is called a “TITLE”.
Chapter
The titles can be subdivided into many sections.
Each section is called a “CHAPTER”.
Video CD/Audio CD Track
A Video CD or Audio CD can contain several items.
These are assigned to the tracks.
Removing Disc from Case
Be sure to hold the edge of disc. Do not touch the surface of the disc.
Pick up the disc gently from the case.
• Do not scratch the disc.
• Do not get dirt on the surface of the disc.
• Do not stick a label or adhesive tape on the disc.
• Do not drop or bend the disc.
Storing Disc
• Store the disc in the case to avoid risk of scratches, dirt or damage.
• Do not leave disc exposed to direct sunlight or in hot or humid places.
Cleaning Disc
Wipe the disc with a clean, dry cloth from center to edge.
• Do not wipe the disc round.
• Do not use liquid or aerosol cleaners.
CHAPTER 1
TITLE1 TITLE2
DVD DISC
CHAPTER 2 CHAPTER 2 CHAPTER 3CHAPTER 1
TRACK 1 TRACK 2 TRACK 3 TRACK 4 TRACK 5
CD
Video CD/Audio CD
The following types of discs can be played on this unit.
Disc type and logo mark Recorded content Disc size
DVD Video
Video CD
Audio CD
CD-R/CD-RW
Audio
+
Video
Audio
CD-DA/JPEG/
MP3/WMA file
5 inches
(12 cm)
3 inches
(8 cm)
5 inches
(12 cm)
3 inches
(8 cm)
5 inches
(12 cm)
3 inches
(8 cm)
5 inches
(12 cm)
3 inches
(8 cm)
Recordable
ReWritable
Region Number
Region number (Regional restriction code) is built-in to the unit and DVD video discs.
Region number “1” or “ALL” of DVD video discs can be used on this unit.
•This unit can play back FUJICOLOR
CD and Kodak Picture CD formats.
•DVD-ROM, SVCD, CVD, Photo CD,
etc. cannot be played.
•Some CD-R/RWs can not be played
back depending on the recording
conditions.
•This unit is to be used exclusively with
the NTSC color system. PAL and
SECAM system discs cannot be used
with this unit.
1
2C51201AE(36-41) 15/3/03, 11:15 AM37
38
Language
OSD Language English English
Francais
Espanol
Other
/Enter/Setup/Return
Picture ParentalSound
Language
OSD Language English
Other
/Enter/Setup/Return
Picture ParentalSound
4
Setting setup language
The setup language can be selected.
Press or ENTER and then
press or to select desired
language (e.g. English), then
press ENTER.
2Press SET UP MENU in the stop
mode. The SETUP MENU of
DVD will appear on the screen.
NOTE: To make the SETUP screen disappear, press SET UP
MENU (or RETURN).
If the DVD/VCR does not operate
properly: Static electricity, etc., may
affect the player's operation. Disconnect
the AC power cord once, then connect
it again.
3Press or ENTER to select
“OSD Language”.
Then press or to select
“Other”.
Language Other
/Enter/Setup/Return
Picture ParentalSound
1Press DVD to select the DVD
mode. (The DVD indicator will
light.)
“No Disc” will appear on the
screen. (If a DVD disc has already
loaded, the playback will start
automatically.)
Turn ON the TV and set it to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
When using an amplifier, switch on the amplifier.
Preparation:
•
•
•
2C51201AE(36-41) 15/3/03, 11:15 AM38
39
4
Reading
Playback procedure
Press OPEN/CLOSE or PLAY.
The disc tray closes automati-
cally.
On the screen, changes to
“Reading” and then playback will
commence.
•A menu screen may appear on
the TV screen, if the disc has
a menu feature. In this case,
press , , , or
ENTER to operate a menu
feature.
1Press OPEN/CLOSE.
The disc tray will open.
2Place a disc onto the tray.
Hold the disc, position it with the
printed label side up, align it with
the guides, and place it in its
proper position.
3
Press STOP to end playback.
•The DVD/VCR memorizes the stopped point, depending on
the disc. “” appears on the screen for approx. 4 seconds.
“” keep blinking in the display until the playback is stopped
completely. Press PLAY to resume playback (from the scene
point).
•If you press STOP again (“
” appears on the screen) or unload
the disc, the DVD/VCR will clear the stopped point.
5Then press OPEN/CLOSE.
The disc tray opens.
Remove the disc and press POWER.
The disc tray closes automatically and DVD/VCR turns off.
•
•
NOTES:
If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV
screen according to the type of loaded disc. In this case, check your disc again (see pages 37 and 52).
Some discs may take a minute or so to start playback.
•
•
•
•
A “Prohibition” symbol may appear at the upper left of the screen. This symbol means either the feature you
tried is not available on the disc, or the DVD/VCR can not access the feature at this time. This does not indicate
a problem with the DVD/VCR.
When you set a single-faced disc label downwards (ie. the wrong way up) and press OPEN/CLOSE or PLAY,
“Reading” will appear and remain on the screen for approx. 40 seconds and then it will change to “Incorrect
Disc”.
Some playback operations of DVDs may be intentionally fixed by software producers. Since this DVD/VCR plays
DVDs according to the disc contents the software producers designed, some playback features may not be
available. Also refer to the instructions supplied with the DVDs.
When playing DTS-encoded Audio CDs, excessive noise will be heard from the analog stereo outputs. To avoid
possible damage to the audio system, the consumer should take proper precautions when the analog stereo
outputs of the DVD/VCR are connected to an amplification system.
Turn ON the TV and set it to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
Preparation:
•
•
2C51201AE(36-41) 15/3/03, 11:15 AM39
40
Special playback
Press FF during normal playback.
Each press of FF will increase the speed of the search (x2),
(x4), (x8), (x20).
• To resume normal playback, press PLAY.
Fast Forward Playback
Press REW during normal playback.
Each press of REW will increase the speed of the search (x2),
(x4), (x8), (x20).
• To resume normal playback, press PLAY.
Review Playback
Press PAUSE during normal
playback.
Still Playback
To resume normal playback, press
PLAY.
Press PAUSE during still playback.
One frame is advanced each time
you press PAUSE.
Frame Advance
• To resume normal playback, press PLAY.
• To resume the still playback, press PAUSE.
Press SLOW during
normal playback or still playback.
Each press of SLOW will change the speed of the slow x1/2, x1/4,
x1/6, x1/7.
Slow-motion Playback
To resume normal playback, press
PLAY.
Locating a chapter or track
The unit is capable of holding a still video
image or On screen display image on your
television screen indefinitely. If you leave
the still video image or On screen display
image displayed on your TV for an ex-
tended period of time, you risk permanent
damage to your television screen.
Projection televisions are very susceptible.
Press SKIP ( ) Forward or SKIP ( ) Reverse during play-
back to locate a chapter that you want to watch.
Each time you press the button, a chapter or track is skipped.
NOTE:
Note: There may be a slight delay be-
tween pressing the button and the
function activation.
2C51201AE(36-41) 15/3/03, 11:15 AM40
41
1
NOTES:
•You can use the Pause, Slow, Search
or Skip feature in the zoom mode.
• In case of the Video-CD playback with
PBC, the SEARCH MODE does not
work.
This unit will allow you to zoom in on the frame image. You can
then make selections by switching the position of the frame.
In the zoom mode press ZOOM repeatedly to return to a 1:1
view ( Off).
1Press ZOOM during playback.
The center part of the image will
be zoomed in.
Each press of ZOOM will change
the ZOOM 1 (x 1.3), 2 (x
1.5) and 3 (x 2.0).
2
3
Zooming
Press / or / to view a different part of the frame.
You may move the frame from the center position to UP, DOWN,
LEFT or RIGHT direction.
Use the title, chapter and time recorded on the disc to
locate the desired point to play back.
Press Number keys to change the number.
• If you input a wrong number, press CANCEL.
• Refer to the package supplied with the disc to check the
numbers.
1Press SEARCH MODE during
playback or stop mode.
3
Locating desired scene
Press ENTER.
Playback starts.
4
• When you change the title, playback starts from Chapter 1 of
the selected title.
• Some discs may not work in the above operation.
2Press or to select the “Time”, “Title” or “Chapter”.
To check the title, chapter and time, press OSD (see page 58).
Zooming/Locating desired scene
Turn ON the TV and set it to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
Preparation:
•
•
2C51201AE(36-41) 15/3/03, 11:15 AM41
42
Repeat
Play Mode Off
All
:
:
/Enter/Play Mode
Chapter
:
Repeat
/Enter/Play Mode
NOTES:
Some discs may not work with the
repeat operation.
In A-B repeat mode, subtitles near
point A or B may not appear.
Repeat playback is not available in
multi-angle scenes.
You may not be able to set A-B Re-
peat, depending on the scenes of the
DVD.
A-B repeat does not work with an in-
teractive DVD, MP3/WMA/JPEG-CD
and Video-CD with PBC.
Repeat playback
Press PLAY to start Repeat playback.
To resume normal playback, select Repeat “Off”.
Repeat playback of Title, Chapter and Track
A-B repeat playback allows you to repeat material between two
selected points.
1Press REPEAT A-B during
playback.
The start point is selected.
2Press REPEAT A-B again.
The end point is selected.
Playback starts at the point that
you selected. Playback stops at
the end point, returns to Point A
automatically, then starts again.
A-B Repeat Playback
CD
•
•
•
•
•
2Press ENTER once or twice to select “Chapter” or “Title”.
In case of CD, at first press to select “Repeat” and then press
ENTER once or twice to select “Track” or “All”.
DVD
Play Mode Off
Repeat Off
/Enter/Play Mode
:
:
CD
1Press PLAY MODE during playback or stop mode.
DVD
3Press PLAY MODE again to make the screen disappear.
•
•
To resume normal playback press REPEAT A-B again.
“
Off
” appears on the screen.
Turn ON the TV and set it to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will
light.)
Preparation:
•
•
Off
:
Repeat
/Enter/Play Mode
AB
A
2C51201AE(42-47) 15/3/03, 11:15 AM42
43
Repeat
Play Mode
:
Random
:
Off
/Enter/Play Mode
Program playback/Random playback (CD)
1Press PLAY MODE in the stop
mode.
2Press ENTER repeatedly until
the Program table as right
appears.
3Example: In case you wish to
program in order of 7, 3, 11:
Enter as 7 , 3 , 11.
If you input a wrong number,
press CANCEL.
4Press / or / to select
“Program Playback” and press
ENTER.
The program you selected will
begin to playback in the order set.
To return to normal playback, select
“Play Mode: Off” at step 2 above.
You can arrange the order of tracks on the disc.
Program playback
Play Mode Off
Repeat Off
/Enter/Play Mode
:
:
Turn ON the TV and set it to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will
light.)
Preparation:
•
•
1Press PLAY MODE in the stop
mode.
Random playback
Play Mode Off
Repeat Off
/Enter/Play Mode
:
:
2Press / to select “Random”.
3Press PLAY.
Random playback will start.
NOTES:
•To cancel program playback, select
“Clear” at step 3 and press ENTER.
•The program is cancelled when you
open the disc tray or turn the power off.
•
In playing back the Video CD with PBC,
you can not set Program playback and
Random playback.
2C51201AE(42-47) 15/3/03, 11:15 AM43
44
4
3
MP3/WMA/JPEG playback
This player can play back the MP3/WMA/JPEG-
data which has been recorded on CD-R or CD-
RW. To produce the MP3/WMA/JPEG-data, you
need a Windows-PC with CD-ROM drive and a
MP3/WMA/JPEG-encoding Software (not
supplied).
The Apple-HFS-System can not be played.
Limitations on MP3/WMA/JPEG CD playback
•
MP3/WMA/JPEG CD is the disc that is standardized
by ISO9660, its file name must include 3-digits
extension letters, “mp3”, “wma”, “jpg”.
•The directory and file names of the MP3/WMA/
JPEG CD must be correspond to the ISO
standardized files.
•This unit can read 200 files per disc. If one
directory has more than 200 files, it reads up to
200 files, the remaining files will be omitted.
•The unit is able to recognize up to a maximum
of 50 directories per disc.
•MP3/WMA CDs cannot be used for playback
for the purpose of recording.
•As for multi-session disc, only the first session
can be played.
•If the CD has both audio tracks and MP3/WMA/
JPEG files, only audio tracks are played.
•It may take more than one minute for this unit to
read MP3/WMA/JPEG files depending on its
structure.
•Music recorded by “Joliet Recording
Specification” can be played back, the file name
is displayed (within 16 letters) on the screen
Long file names will be condensed.
•The music files recorded by “Hierarchical File
System” (HFS) cannot be played.
•The unit can play back baseline and progressive
JPEG files.
A file menu screen will appear on
the TV screen.
Press / to select folder.
Press / or / or Number keys to select the desired
file.
• In case the folder includes more than 15 files, press or
to display next file list.
Limitations on display
•The maximum number for display is 16 letters.
Available letters for display are the following:
capital or small alphabets of A through Z,
numbers of 0 through 9, and _ (under score).
•Other letters than those above are replaced
in hyphen.
Notes on MP3/WMA/JPEG files
To play back MP3/WMA/JPEG CD in the recorded
order,
1. Use MP3/WMA/JPEG software that records
data alphabetically or numerically.
2. Name each file including two-digit or three-
digit number (e.g. “01” “02” or “001” “002”).
3. Refrain from making too many sub-folders.
CAUTION:
•Some MP3/WMA/JPEG CDs can not be played
back depending on the recording conditions.
•The CD-R/RW that has no music data or non-
MP3/WMA/JPEG files can not be played back.
6Press STOP to end playback.
• The unit records the stopped point. “” appears on the screen.
Press PLAY to resume playback (from the scene point).
• If you press STOP again or unload the disc, the unit will clear
the stopped point.
1
Press OPEN/CLOSE.
The disc tray will open.
Place a disc on which MP3 or WMA
files have been recorded onto the tray.
2Press OPEN/CLOSE or PLAY. The
disc tray closes automatically. On the
TV-screen, “Reading” will appear.
Reading will take as much time as
the number of file.
MP3/WMA/JPEG CD information
NOTES:
During MP3/WMA/JPEG-Playback, you can not use SEARCH,
A-B Repeat functions.
You can use Repeat (Track or All), Random functions and Program
playback for MP3/WMA/JPEG CD Playback (see pages 42 and 43).
In the case of a CD containing a mixture of MP3, WMA and JPEG
files, the files are played back by selecting them from the file menu.
•
•
•
Turn ON the TV and set it to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will
light.)
Preparation:
•
•
/0-9/Enter/Play Mode
1
-
/72
2
3
4
5
Japan
CD-R
Bay Bridge
CLOSE MY EYES
DIVE TO BLUE
Honey
8
9
10
11
12
flower
Lies and Truth-
winter fall
Rain
Strawberry
6
BLUE EYES
13
Welcome party
7
Blurry Eyes
14
Thailand
Pops
--:--
/0-9/Enter/Play Mode
15
-
/72
16
Mother
CD-R
Hold Your Last
Pops
--:--
MP3/WMA CD playback
1
-
/72
--:--
/0-9/Enter/Play Mode
2
3
4
5
Japan
CD-R
Bay Bridge
CLOSE MY EYES
DIVE TO BLUE
Honey
8
9
10
11
12
flower
Lies and Truth-
winter fall
Rain
Strawberry
6
BLUE EYES
13
Welcome party
7
Blurry Eyes
14
Thailand
Pops
• When PLAY has been pressed after displaying the file menu,
or when the disc tray has been closed after pressing PLAY in
step 2, playback begins automatically starting from the first
file. In this case, if the first file is an MP3/WMA file, only MP3/
WMA files are played back in order. If the first file is a JPEG
file, the first JPEG file is played back.
Press ENTER.
The selected file starts playing back.
5
2C51201AE(42-47) 15/3/03, 11:15 AM44
45
4
3A file menu screen will appear on
the TV screen.
Press / to select folder.
To display a picture menu, press
DVD MENU. (To return to a file
menu, press TITLE.)
Press / or / to select
the desired file.
• To display next list, press SKIP
/.
• When PLAY has been pressed after displaying the file menu,
or when the disc tray has been closed after pressing PLAY
in step 2, playback begins automatically starting from the
first file. In this case, if the first file is a JPEG file, the first
JPEG file is played back. If the first file is an MP3/WMA file,
only MP3/WMA files are played back in order.
1Press OPEN/CLOSE.
The disc tray will open.
Place a disc on which JPEG files
have been recorded onto the tray.
2Press OPEN/CLOSE or PLAY.
The disc tray closes automatically.
On the TV-screen, “Reading” will
appear. Reading will take as much
time as the number of file.
Turn ON the TV and set it to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator
will light.)
Preparation:
•
•
JPEG CD playback
Press / or / or Number
keys to select the desired file.
6Press STOP to end playback.
The file menu appears on the TV screen.
If you want to watch the other file, repeat steps 4-5.
NOTE:
The picture menu is displayed when the
FUJICOLOR CD or the Kodak Picture CD are
played. To display the file menu press TITLE.
5Press ENTER.
The selected picture appears on
the TV screen.
About file menu
2C51201AE(42-47) 15/3/03, 11:15 AM45
46
Setting the JPEG Interval
Press SET UP MENU in the
stop mode.
Press / to select “Picture”,
then press or ENTER.
Turn ON the TV and set it to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will
light.)
Preparation:
•
•
Setting the JPEG Interval
You can continuously play back all JPEG files automatically.
/Enter/Setup/Return
Language Picture Parental OtherSound
Press ENTER.
Press or to select your
desired time.
1
2
3
Press or to select “JPEG
Interval”.
To make SETUP screen disappear, press SET UP MENU.
4
Off:
Plays back one file at a time.
5 Seconds:
Plays back images in the form of a slide show at 5 second
intervals.
10 Seconds:
Plays back images in the form of a slide show at 10 second
intervals.
15 Seconds:
Plays back images in the form of a slide show in 15 second
intervals.
2C51201AE(42-47) 15/3/03, 11:15 AM46
47
/Enter/Setup/Return
Language Picture Parental OtherSound
Setting the Select Files
Press SET UP MENU in the
stop mode.
Press / to select “Picture”,
then press or ENTER.
Turn ON the TV and set it to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will
light.)
Preparation:
•
•
Press ENTER.
Press or to select your
desired file type.
1
2
3
Press or to select “Select
Files”.
To make SETUP screen disappear, press SET UP MENU.
4
All:
Displays all files.
Music Only:
Displays only MP3/WMA files.
Pictures Only:
Displays only JPEG files.
When playing back a CD containing
a mixture of MP3, WMA and JPEG
files, only MP3/WMA or JPEG files
can be displayed on the file menu.
2C51201AE(42-47) 15/3/03, 11:15 AM47
48
Press ZOOM during playback.
Enlarged JPEG images are displayed.
You can make the images even larger by repeatedly pressing
ZOOM.
Zooming
This unit will allow you to zoom in on the JPEG image.
1
12
Off
3
2In the zoom mode, press ZOOM repeatedly to return to a 1:1
view ( Off).
Press ANGLE during playback.
Images are rotated 90 degrees
to the right.
Changing angles
You can display JPEG images rotating at 90 degree intervals.
1
2Press ANGLE repeatedly until the desired angle is selected.
Pressing ANGLE four times returns the image to its original
angle.
•Images are displayed at the same angle until the disc is
removed.
Zooming/Changing angles (JPEG CD)
Preparation:
•Turn ON the TV and set it to the video input mode.
•Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
2C51201AE(48-51) 15/3/03, 11:16 AM48
49
Marking desired scenes
1Press MARKER during
playback.
2Select the blank Marker using
/ .
Then press ENTER at the desired
scene.
•Repeat this procedure to set
the other 2 scenes.
3Press MARKER to remove this display.
The unit stores the points that you
want to watch again up to 3 points.
You can resume playback from
each scene.
Marking the scenes
1Press MARKER during playback
or stop mode.
Returning to the scenes
2Press / to select the Marker
1-3.
3Press ENTER.
Playback starts from the marked scene.
NOTES:
Some discs may not work with the
marking operation.
The marking is canceled when you
open the disc tray or turn the power off.
Some subtitles recorded around the
marker may fail to appear.
•
•
•
1Press MARKER.
To cancel the mark
2Press / to select the Marker 1-3.
3Press CANCEL.
To remove this display, press MARKER.
Preparation:
•Turn ON the TV and set it to the video input mode.
•Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
2C51201AE(48-51) 15/3/03, 11:16 AM49
50
Changing soundtrack language/Karaoke playback
1Press A.MONITOR during
playback.
The current soundtrack language
will appear.
2Press A.MONITOR repeatedly
until the desired language is
selected.
The on-screen display will
disappear after a few seconds.
Changing soundtrack language
Turn ON the TV and set it to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
Preparation:
•
•
You can select the language when you play a multilingual disc.
In case of VIDEO CD playback
Audio type changes as follows each time you press A.MONITOR.
NOTES:
The vocal output feature is used during
playback of Dolby Digital (multi-channel)
recorded DVD KARAOKE discs. This
feature allows you to turn off vocal audio
tracks, or restore them for background
accompaniment.
When playing Karaoke, connect
appropriate audio equipment such as an
amplifier to the DVD/VCR.
•
•
LR
L
R
Karaoke playback
When playing back a DVD KARAOKE disc, you can turn the
vocal on or off.
1Press A.MONITOR during DVD
KARAOKE disc playback.
1/8 Eng Dolby Digital
Off
3Press or to select “On” or
“Off”.
On: The primary vocal is output when it is recorded on the
disc.
Off: The primary vocal is not output.
2Press or to select Karaoke
vocal setting.
2C51201AE(48-51) 15/3/03, 11:16 AM50
51
Subtitles/Changing angles/Title selection/DVD menu
When playing back a disc recorded with multi-angle facility,
you
can change the angle that you are viewing the scene from.
1Press ANGLE during playback.
The current angle will appear.
2Press ANGLE repeatedly until the
desired angle is selected.
Changing Angles
Two or more titles are recorded on some discs. If the title menu
is recorded on the disc, you can select the desired title.
Press ENTER or PLAY.
The playback of the selected title will start.
1Press TITLE during playback.
Title menu appears on the screen.
•Press TITLE again to resume playback at the scene when you
pressed TITLE.
2Press / or / to select the desired title.
3
Title Selection
Some DVDs allow you to select the disc contents using the
menu.
When you play back these DVDs, you can select the subtitle
language and sound-track language,etc. using the DVD menu.
Press ENTER.
The menu continues to another screen.
Repeat steps 2 and 3 to set the item completely.
1Press DVD MENU during playback.
The DVD menu appears on the screen.
•Press DVD MENU again to resume playback at
the scene when you pressed DVD MENU.
2Press / or / to select the desired item.
3
DVD Menu
NOTES:
If the desired language is not heard
after pressing the SUBTITLE button
several times, the language is not
recorded on the disc.
Changing soundtrack or subtitle
language is cancelled when you open
the disc tray. The initial default lan-
guage or available language will be
heard and seen if the disc is played
back again.
Depending on the DVD you may be
unable to turn on, turn off, or change
the subtitles, even if they are recorded
on the disc. While playing the DVD,
the subtitle may change while opening
or closing the disc tray, or while
changing the title.
In some cases, the subtitle language
is not changed to the selected one
immediately.
Depending on the DVD, you may not
be able to change the angles even if
multi-angles are recorded on the disc,
or you may be unable to select the title,
and a “title menu” may simply be called
a “menu” or “title” in the instructions
supplied with the disc.
Turn ON the TV and set it to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
Preparation:
•
•
1/9
Press SUBTITLE during playback
until “OFF” appears.
Turning the Subtitles On and Off
Press SUBTITLE repeatedly during
playback until your desired language
appears.
The on-screen display will disappear
after a few seconds.
You can select the language when playing back a disc
recorded with multi-lingual subtitles.
Changing the subtitle language
When playing back a disc recorded with subtitles, you can turn
the subtitles on or off.
Off
1/32 Eng
•
•
•
•
•
2C51201AE(48-51) 15/3/03, 11:16 AM51
52
Parental control
1Press SET UP MENU in the stop mode.
Press or to select “Parental”.
Then press or ENTER.
2Press or to select “Parental 8”,
then press ENTER until the level you
desire appears (e.g.: 1).
3Press once to select “Password ”.
4Press ENTER.
1234
change to .
Parental control setting
Turn ON the TV and set to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
Preparation:
•
•
• If you input a wrong number, press
CANCEL.
• Be sure to remember this number!
Some discs are specified not suitable
for children. Such discs can be
prevented from play back with the
unit.
Level Off : The parental control setting does not function.
Level 1 : DVD software for adults cannot be played back.
Level 8 : All DVD software can be played back.
Select from level 1 to level 8.
On a scale of 1-8, “1” is the most restrictive.
Then press Number keys to input a 4-
digit
password (e.g.: 1234).
Password
Parental
1
/Enter/Setup/Return
Language Picture Parental OtherSound
5To make SETUP screen disappear, press SET UP MENU.
1Select “Password ” (step 1)
and press Number keys to input your
4-digit password.
Then press ENTER.
To unlock the Parental Control Setting
2If the input password was right,
will appear.
You can move to “Parental 1”(e.g.) to
input the desired level or to cancel
parental control.
Cancel the password so as to set the Parental level freely again,
NOTES:
If each setup (page 46~48, 52~59) has
been completed, the unit can always
be worked under the same conditions
(especially with DVD discs).
Each setup will be retained in the
memory if you turn the power off.
Depending on the discs, the unit can-
not limit playback.
Some discs may not be encoded with
specific rating level information though
its disc jacket says “adult”. For those
discs, the age restriction will not work.
Do not forget the password. If you forget
the password, contact customer service.
•
•
•
•
2C51201AE(52-57) 15/3/03, 11:16 AM52
53
Temporary disabling of rating level by DVD disc
If you wish to cancel the set rating level temporarily, select
“Parental Control Level” with or , then press ENTER. If
the 4-digits password at step 3 on page 52 has been set, the
password entering screen will appear as shown in step 4 below.
Alternatively, if the password has not been set, playback will
commence. If you don’t know (or have forgotten) the password,
select “Cancel Picture”.
The setting screen will disappear. Press OPEN/CLOSE to
remove the disc.
1Load a DVD disc and press
OPEN/CLOSE or PLAY (see
page 39).
2If the DVD disc has been designed to temporarily cancel the
Rating level, the screen which follows the “Reading” screen will
change, depending on which disc is played. If you select “YES”
with ENTER key, “Your disc exceeds the parental control level
1.”(e.g.) screen will then appear.
3
Enter the password with
Number buttons (0-9).
Then press ENTER.
4
Playback will commence if the entered password was correct.
5
NOTE:
This temporary cancellation of rating
level will be kept until the disc is ejected.
When the disc is ejected, the original
rating level will be set again
automatically.
Depending on the DVD disc, the
disc may try to temporarily cancel
the rating level that you have set.
It is up to you to decide whether to
cancel the rating level or not.
If you interrupt the entering,
press RETURN.
Turn ON the TV and set to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
Preparation:
•
•
Your disc exceeds
the parental control level 1.
Parental Control Level
Cancel Picture
/Enter/Return
2C51201AE(52-57) 15/3/03, 11:16 AM53
54
Setting menu language
Press or ENTER.
Press or to select your
desired language, then press
ENTER.
1
2
3
To make SETUP screen disappear, press SET UP MENU.
Other: Other language can be selected (See the Language
code list on page 61).
English, Francais, Espanol
The selected language is the first-priority Menu language.
Press or ENTER.
Then press or to select
“Menu”.
4
You can select the language of the
disc menu messages of DVDs. Turn ON the TV and set to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
Preparation:
•
•
Press SET UP MENU in the stop
mode.
Press or to select
“Language”.
/Enter/Setup/Return
Language Picture Parental OtherSound
Language Picture Parental OtherSound
Menu
Subtitle
Audio
English
Automatic
English
/Enter/Setup/Return
2C51201AE(52-57) 15/3/03, 11:16 AM54
55
Menu
Subtitle
Audio
English
Automatic
English
/Enter/Setup/Return
Language Picture Parental OtherSound
If you want to select another language, enter the language code
(see the language code list on page 61).
Other:
English, Francais, Espanol
The subtitle is displayed with the selected language if it is
recorded on the disc.
Setting subtitle language
Press or ENTER.
Press or to select your
desired language, then press
ENTER.
1Press SET UP MENU in the stop
mode.
Press or to select
“Language”.
2
3
To make SETUP screen disappear, press SET UP MENU.
4
NOTE:
If the selected language is not recorded
on the disc, the first-priority language is
selected.
The same subtitle language can
always be selected even if you replace
the disc or turn the power off.
Press or ENTER.
Then press or to select
“Subtitle”.
• The unit will automatically select the same language in the
AUDIO setting.
•When the unit selects the same language as the AUDIO, the
subtitles will not appear during playback.
•When you do not use the same language as the AUDIO, the
subtitles will appear during playback.
Automatic:
Subtitles do not appear.
Off:
Turn ON the TV and set to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
Preparation:
•
•
/Enter/Setup/Return
Language Picture Parental OtherSound
2C51201AE(52-57) 15/3/03, 11:16 AM55
56
Language Picture Parental OtherSound
Menu
Subtitle
Audio
English
Automatic
English
/Enter/Setup/Return
Setting audio soundtrack language/Setting surround sound
Press or ENTER.
Press or to select your
desired Audio Language, then
press ENTER.
1Press SET UP MENU in the stop
mode.
Press or to select “Language”.
2
3
To make SETUP screen disappear, press SET UP MENU.
4
NOTES:
If the selected language is not
recorded on the disc, the original
language will be heard.
The “SPATIALIZER N-2-2” is effective
only for the sound of disc.
The same audio soundtrack language
can always be selected by your unit
even if you replace the disc or turn
the power off.
•English, Francais, Espanol:
The language you have selected will play if it is recorded on
the disc.
•Other: If you want to select another language,
enter the language code (See the Language code list on page
60).
•Original: The unit will select the first priority language of each
disc.
Press or ENTER.
Then press or to select
“Audio”.
Turn ON the TV and set to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
Preparation:
•
•
/Enter/Setup/Return
Language Picture Parental OtherSound
Setting surround sound
This DVD/VCR equipped with a “SPATIALIZER N-2-2”. It can
produce the effect of being in a cinema or a concert hall.
1During disc playback press
A. MONITOR.
Press to select “On”.
2
•
•
To cancel Surround mode:
Follow the right steps 1~2, then press to select the “Off” position.
Setting audio soundtrack
language
2C51201AE(52-57) 15/3/03, 11:16 AM56
57
/Enter/Setup/Return
Language Picture Parental OtherSound
Setting the aspect ratio of TV screen
Press or ENTER.
Press or to select your
desired screen type, then press
ENTER.
1Press SET UP MENU in the stop
mode.
Press or to select “Picture”.
2
3
To make SETUP screen disappear, press SET UP MENU.
4
NOTE:
If the DVD disc is not formatted in the pan
& scan style, it displays 4:3 style.
You can select the aspect ratio for
your TV.
4:3 Letter box
Select this mode when connecting to a conventional TV. When
playing back a wide screen-DVD disc, it displays the wide picture
with black bands at the top and bottom of screen.
4:3 Pan scan
It displays the wide picture on the whole screen with left and
right edges automatically cut off.
16:9 Wide
Select this mode when connecting to a wide-screen TV.
A wide screen picture is displayed full size.
Press or ENTER, then press
or to select “Tv Screen”.
You have the following screen sizes to choose from:
Turn ON the TV and set to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
Preparation:
•
•
2C51201AE(52-57) 15/3/03, 11:16 AM57
58
Setting on screen display/Status display of disc
Press or ENTER to select “On”
or “Off”.
1
2
3
To make SETUP screen disappear, press SET UP MENU.
4
On screen display can be switched on
or off when you press the buttons.
On: On screen displays appears when you press the any
buttons (factory setting).
Off: On screen displays do not appear when you press any
buttons except SET UP MENU, SEARCH MODE, PLAY
MODE, MARKER and OSD.
Press or ENTER, then press
or to select “Display”.
00:34:56 01:12:33
Each press of OSD, the status display of the disc will appear on the
screen and change as follows.
DVD
AUDIO
CD
Status display of disc
Turn ON the TV and set to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
Preparation:
•
•
Press SET UP MENU in the stop
mode.
Press or to select “Picture”.
00:34:56 01:12:33
1/9
Title 1/99
1/8
1/32
Chapter 1/999
Eng Dolby Digital
Eng
VIDEO
CD
34:56 71:33
Track 11/99
To make status display disappear, press OSD again.
/Enter/Setup/Return
Language Picture Parental OtherSound
When you playback the CD disc, the status display will appear on
the screen and continue displaying.
2C51201AE(58-Back) 15/3/03, 11:16 AM58
59
/Enter/Setup/Return
Language Picture Parental OtherSound
DRC
Max
Std
Min
/Enter/Setup/Return
Language Picture Parental OtherSound
Std
Dynamic Range Control
Press or ENTER, then
press or to select
desired setting.
1Press SET UP MENU in the stop mode.
Press or to select
“Sound”.
2
3
DRC (Dynamic Range Control) enables
you to control the dynamic range so
as to achieve a suitable sound for
your equipment.
Max: Full dynamic range is increased.
Std: Full dynamic range is maintained.
Min: Dynamic range is reduced.
Press or ENTER to
select “DRC”.
NOTES:
•This function works only during playback
of Dolby Digital recorded discs.
•The level of Dynamic Range Reduction may
differ depending on DVD video disc.
Turn ON the TV and set to the video input mode.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
Preparation:
•
•
2C51201AE(58-Back) 15/3/03, 11:16 AM59
60
Progressive scan
The unit supports the Progressive
scanning system as well as the
conventional interlaced scanning
system. If your television or monitor
equipped with component jacks
support the progressive video input,
you can enjoy a high quality picture
by making the Progressive scanning
modo active.
•Connect to a TV equipped with component jacks.
•Turn On the TV and set it to the corresponding video input mode.
•Set the S-VIDEO /COMPONENT video selector switch on the
rear panel to COMPONENT position.
•Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
Preparation:
1Press PROGRESSIVE in the stop mode. The PROGRESSIVE
indicator “ ” on the display window is lit.
•The unit recognizes the picture type (film or video source) of
the current disc according th the disc information.
2Press PLAY to start playback.
•To make the progressive scanning mode inactive, press
PROGRESSIVE in the stop mode. The PROGRESSIVE
indicator “ ” on the display window is not lit.
About SCANNING MODE
To display video on the television (monitor) screen, the conventional
scanning method is called “Interlaced scanning.” With this method,
only half of the horizontal lines are displayed at a time. So two fields
complete a single picture (frame); i.e., the first field, containing all
the odd-numbered lines, is displayed followed by the second field,
containing all the even-numbered lines.
On the other hand, the Progressive scanning system scans all
horizontal lines at a time, so you can double the number of pictures
compared with the interlaced scanning, resulting in flicker-free,
high-density picture.
To enjoy the progressive scanned video, a monitor (or TV or
projector) to be connected to the unit must have the Progressive
inputs.
Depending on the material source format, DVD VIDEO discs can be
classified into two types; film source and video source (note that
some DVD VIDEO discs contain both film source and video
source). Film sources are recorded as 24-frame-per-second
information, while (NTSC) video sources are recorded as 30-
frame-per second (60-field-per-second interlaced) information.
When the unit plays back a film source material, uninterlaced
progressive output signals are created using the original information.
When a video source material is played back, the unit interleaves
lines between the interlaced lines on each to create the interpolated
picture and putputs as the progressive signal.
S-VIDEO/COMPONENT
Video selector switch
NOTES:
•Some discs may not be played back with the progressive scanning mode correctly because of the disc
characteristics or recording condition.
•There are some progressive TV and High-Definition TV sets that are not fully compatible with the unit, resulting
in the unnatural picture when playing back a DVD VIDEO disc in the Progressive scanning mode. In such a case,
use the Interlaced scanning mode. To check the compatibility of your TV set, contact your local JVC customer
service center.
•You cannot make the progressive scanning mode active in following cases.
– The unit is in the VCR mode.
– The disc is played back in the DVD mode.
– The S-VIDEO/PROGRESSIVE video selector swich is set to S-VIDEO positon.
2C51201AE(58-Back) 15/3/03, 11:16 AM60
61
Language code list
Enter the appropriate code number for the initial settings “Audio”, “Subtitle” and/or “Menu” (see pages 54-
56).
Abkhazian 1112 Fiji 1620 Lingala 2224 Singhalese 2919
Afar 1111 Finnish 1619 Lithuanian 2230 Slovak 2921
Afrikaans 1116 French 1628 Macedonian 2321 Slovenian 2922
Albanian 2927 Frisian 1635 Malagasy 2317 Somali 2925
Amharic 1123 Galician 1722 Malay 2329 Spanish 1529
Arabic 1128 Georgian 2111 Malayalam 2322 Sundanese 2931
Armenian 1835 German 1415 Maltese 2330 Swahili 2933
Assamese 1129 Greek 1522 Maori 2319 Swedish 2932
Aymara 1135 Greenlandic 2122 Marathi 2328 Tagalog 3022
Azerbaijani 1136 Guarani 1724 Moldavian 2325 Tajik 3017
Bashkir 1211 Gujarati 1731 Mongolian 2324 Tamil 3011
Basque 1531 Hausa 1811 Nauru 2411 Tatar 3030
Bengali; Bangla 1224 Hebrew 1933 Nepali 2415 Telugu 3015
Bhutani 1436 Hindi 1819 Norwegian 2425 Thai 3018
Bihari 1218 Hungarian 1831 Oriya 2528 Tibetan 1225
Breton 1228 Icelandic 1929 Panjabi 2611 Tigrinya 3019
Bulgarian 1217 Indonesian 1924 Pashto, Pushto 2629 Tonga 3025
Burmese 2335 Interlingua 1911 Persian 1611 Turkish 3028
Byelorussian 1215 Irish 1711 Polish 2622 Turkmen 3021
Cambodian 2123 Italian 1930 Portuguese 2630 Twi 3033
Catalan 1311 Japanese 2011 Quechua 2731 Ukrainian 3121
Chinese 3618 Javanese 2033 Rhaeto-Romance 2823 Urdu 3128
Corsican 1325 Kannada 2124 Romanian 2825 Uzbek 3136
Croatian 1828 Kashmiri 2129 Russian 2831 Vietnamese 3219
Czech 1329 Kazakh 2121 Samoan 2923 Volapük 3225
Danish 1411 Kirghiz 2135 Sanskrit 2911 Welsh 1335
Dutch 2422 Korean 2125 Scots Gaelic 1714 Wolof 3325
English 1524 Kurdish 2131 Serbian 2928 Xhosa 3418
Esperanto 1525 Laothian 2225 Serbo-Croatian 2918 Yiddish 2019
Estonian 1530 Latin 2211 Shona 2924 Yoruba 3525
Faroese 1625 Latvian, Lettish 2232 Sindhi 2914 Zulu 3631
Language Name Code Language Name Code Language Name Code
Language Name Code
2C51201AE(58-Back) 15/3/03, 11:16 AM61
62
SYMPTOMS POSSIBLE SOLUTIONS
•Make sure the power cord is plugged in.
•Try another AC outlet.
•Power is off, check fuse or circuit breaker.
•Unplug unit, then plug it back in.
•Select the DVD or VCR mode before operating.
•Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
DVD/VCR does not operate.
Problems and troubleshooting
Use the following check list for troubleshooting when you have problems with your unit. Consult your local
dealer or service outlet if problems persist.
Be sure all connections are properly made when using with other units.
DVD/VCR
PAGE
5
–
–
5
20,38
20,38
The remote control does not
function.
• Aim the remote control at the remote sensor.
• Operate within Approx. 5 Meters or reduce the light in the room.
• Clear the path of the beam.
• The batteries are weak. Replace the batteries.
• Check the batteries are inserted correctly.
• Check the frequency code is set correctly.
11
DVD
No picture.
•
Antenna connection is not correct or antenna cable is disconnected.
• The video channel is not in the correct position or the TV is not
set to the video channel 3 or 4.
• Check the unit is connected correctly.
• The video input selector of the TV is not set to VIDEO. Set to
VIDEO (or equivalent).
• Channel is set to the external mode.
No sound.
• Check the unit is connected correctly.
• Check the input selector of the amplifier is set properly.
• The unit is in the Special playback mode.
14~17
20
14~19
–
–
14~19
–
28,40
•Select proper language in the menu options.
Display is not shown in your
language. 38
Playback doesn’t start. • No disc is inserted.
• The disc may be dirty. Clean up the disc.
• The unit cannot play DVD-ROMs, etc.
39
37
37
No CATV reception •Check all CATV connections.
•Station or CATV system problems, try another station. 16,17
Noise bars on screen.
• Tracking adjustment beyond range of automatic tracking circuit.
Try Manual tracking adjustment.
• Video heads are dirty.
• The tape is worn or damaged.
VCR
•The erase prevention tab of the video cassette is broken off.
•The unit is in the external input mode.
TV recording does not work. 26,30
Timer recording does not work. • The time is not set correctly.
• The recording start/end time is not set correctly.
• The TIMER has not been pressed ( is not lit).
23,25
33
33
28
63
–
No POWER but a picture appears
on the TV screen.
•During the Auto Clock operation, a video signal can be put out.
Please set the clock with Manual clock setting or wait until the
Auto Clock operation completed.
25
The DVD-keys on the RCU of the
other JVC RECEIVER/TV is not
effective.
•This is not a defect. Since this unit is combined type of DVD
and VCR, the remote code of DVD is individual. 12,13
2C51201AE(58-Back) 15/3/03, 11:16 AM62
63
No subtitle • Some discs have no subtitles.
• Subtitles are cleared. Press SUBTITLE.
Angle cannot be changed. • Multi-angles are not recorded on the DVD disc.
• The function is prohibited with the unit or the disc.
appears on the screen.
51
51
39
SYMPTOMS POSSIBLE SOLUTIONS PAGE
Problems and troubleshooting/Video head cleaning
NOTES: •DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THE
REAR COVER.
•Video heads may eventually wear out and should be replaced when they fail to produce clear pictures.
•To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.
Video head cleaning
Video head clogging
The video heads are the means by which the DVD/VCR reads
the picture from the tape during playback. In the unlikely event
that the heads become dirty enough to be clogged, no picture
will be played back. This can easily be determined if, during
playback of a known good tape, there is good sound, but no
picture (picture is extremely snowy). If this is the case, have
the DVD/VCR checked by qualified service personnel. Good Picture Snowy Picture
Auto Clock Setting
Notes for Canadian customers regarding the clock feature of your DVD/VCR.
The XDS signals are carried only by certain broadcast television stations (for example, the signal is carried by
most Public Broadcasting Service stations). You must be able to receive a station carrying the XDS signal to
use the Auto Clock Setting to set your DVD/VCR’s internal clock. If you live in an area that does not broadcast
XDS signals, you must set the clock manually. Please see page 25 for instructions on how to manually set your
DVD/VCR’s clock.
Special note for residents of Newfoundland:
The Auto Clock Setting cannot be used to set the DVD/VCR’s internal clock to Newfoundland time. The time
zone command does not include a setting for the Newfoundland time zone. Trying to use the Auto Clock Setting
in the Newfoundland time zone could result in an incorrect time setting or no setting at all. Please set your DVD/
VCR’s clock using the Manual Clock Setting.
Notes
No 4:3 (16:9) picture • The setup does not match your TV.
No on-screen display • Select Display On.
57
58
No surround sound • The setup does not match your stereo system.
The unit or remote operation key
is not functioning. • Turn off the unit and unplug the AC power cord for several
minutes, then replug it.
19
Playback does not start when the
title is selected. • Check the Parental setup.
Audio soundtrack and/or subtitle
language is not changed when you
play back a DVD. • Multilingual language is not recorded on the DVD disc.
–
52
55,56
Stopping playback, search, slow-
motion play, repeat play, or program
play, etc. cannot be performed. • Some discs may not do some of the functions. –
No picture, or the screen is blurred
or divided into two parts.
• The S-VIDEO/COMPONENT selecter is not set correctly.
• The progressive scanning mode is active through the unit is
connected to a TV via the VIDEO OUT jack.
18
60
2C51201AE(58-Back) 15/3/03, 11:16 AM63
64
GENERAL
Power supply:
Power consumption:
Weight:
Dimensions:
Inputs/Outputs:
Video:
Audio:
Antenna:
Hi-Fi Frequency Response:
Hi-Fi Dynamic Range:
VCR section
Video Head:
Audio Track:
Tuner:
RF Channel Output:
F.FWD/REW Time:
DVD section
Signal system:
Applicable disc:
Audio characteristics:
Frequency response:
S/N Ratio:
Harmonic distortion:
Wow and flutter:
Dynamic range:
Output:
Pickup:
ACCESSORIES:
AC 120V 60Hz
Operation: 18W
Stand by: 2W
7.9lbs (3.6 kg)
Width : 16-15/16 inches (430 mm)
Height: 3-7/8 inches (99 mm)
Depth : 9-13/16 inches (249 mm)
In: 1Vp-p/75 ohm
Out: 1Vp-p/75 ohm
In: –8 dBm/50k ohm
Out: –8 dBm/1k ohm
UHF/VHF IN/OUT: 75 ohm coaxial
20Hz to 20,000Hz
More than 90dB
4 Rotary Heads
Hi-Fi Sound - 2 Tracks / MONO Sound - 1 Track
181 Channel Freq. Synthesized
VHF 2-13
UHF 14-69
CATV 14-36 (A)-(W)
37-59 (AA)-(WW)
60-85 (AAA)-(ZZZ)
86-94 (86)-(94)
95-99 (A-5)-(A-1)
100-125 (100)-(125)
01 (5A)
Channel 3 or 4, Switchable
Approx. 1 minute 48 seconds (with T-120 Cassette Tape) (at+25°C)
NTSC
DVD (12cm, 8cm), CD (12cm, 8cm)
DVD: 4Hz - 22kHz
CD: 4Hz - 20kHz
90dB
0.02%
Less than 0.01% Wrms
More than 90dB
Video : (RCA) 1 Vp-p/75 ohm
Audio : (RCA) –8 dBm/1k ohm
Digital Audio : 0.5Vp-p 75 ohm
CD : Wavelength: 775 - 805 nm
Maximum output power: 0.5 mW
DVD : Wavelength: 640 - 660 nm
Maximum output power: 1.0 mW
Remote control x 1
Batteries (2 x AA)
75 ohm Coaxial Cable x 1
AUDIO/VIDEO Cable x 1
Specifications
2C51201AE(58-Back) 15/3/03, 11:16 AM64
65
HOW TO LOCATE YOUR JVC SERVICE CENTER
— JVC
TOLL FREE: 1-800-537-5722
http://www.jvc.com
Dear Customer,
In order to receive the most satisfaction from your purchase, please read the instruction booklet before operating
the unit. In the event that repair is necessary, or for the address nearest your location within the Continental
United States, please call 1-800-537-5722 for your nearest authorized servicer or visit our website at
www.JVC.com. Remember to retain your Bill of Sale for Warranty Service.
DIVISION OF JVC AMERICAS CORP.
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering
and production of the wide array of JVC products, service is the key to maintaining the high level performance
for which JVC is world famous. The JVC service and engineering organization stands behind our products.
NATIONAL HEADQUARTERS
JVC SERVICE & ENGINEERING COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
10 New Maple Avenue
Pine Brook, NJ 07058-9641
JVC SERVICE & ENGINEERING
COMPANY OF AMERICA
CAUTION
To prevent electrical shock, do not open the cabinet.
There are no user serviceable parts inside.
Please refer to qualified service personnel for repairs.
ACCESSORIES
To purchase accessories for your JVC product, you
may contact your local JVC Dealer.
From the 48 Continental United States call toll free:
1-800-882-2345 or on the web at www.JVC.com
Don’t service the product yourself.
FOR SERVICING (Only in U.S.A.)
2C51201AE(58-Back) 15/3/03, 11:16 AM65
66
LIMITED WARRANTY CONSUMER VIDEO 1-90
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE
ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the
date of original retail purchase for the period as shown below. (“The Warranty Period”)
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND
IN COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such
repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service
centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and parts
thereof may be brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen
size 25 inches and above which are covered on an in-home basis.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized
service center, please call toll free: (800) 537-5722.
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy
of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and
location of which will be given to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty
installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by
JVC to render such service, or if affixed to any attachment not provided with the products, or if the model or serial
number has been altered, tampered with, defaced or removed;
2. Initial installation and installation and removal for repair;
3. Operational adjustments covered in the Owner’s Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;
7. Accessories;
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);
There are no other express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY,
IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER
DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE
TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD
SET FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied
warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and
you may also have other rights which vary from state to state.
JVC COMPANY OF AMERICA 1700 Valley Road
DIVISION OF JVC AMERICAS CORP. Wayne, New Jersey 07470
WARRANTY (Only in U.S.A.)
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR
DETAILS OF REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT
WARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the
cabinet. Retain this information for future reference.
Model No.: Serial No.:
Purchase date: Name of dealer:
2C51201AE(58-Back) 15/3/03, 11:16 AM66
67
MEMO
2C51201AE(58-Back) 15/3/03, 11:16 AM67
68
J2C51201A
03/04 U
VICTOR COMPANY OF JAPAN, LIMITED
Printed in Thailand
0403-AH-OR-OR
2C51201AE(58-Back) 17/3/03, 3:55 PM68

Navigation menu