Philio Technology PAD07 In Wall Smart Dimmer User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3375900
Application ID	kHzgtiDyHNhP37CjHFqQFw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	19.86kB (248212 bits)
Date Submitted	2017-04-30 00:00:00
Date Available	2017-04-30 00:00:00
Creation Date	2017-02-08 16:41:16
Producing Software	LibreOffice 5.0
Document Lastmod	0000-00-00 00:00:00
Document Title	User manual
Document Creator	Writer

Built-in High Breaking Capacity current fuse protection. Rating : 2A /250V.
PAD07 In Wall Smart Dimmer
Built-in Thermal Cutoff Fuses protection. Rated Temperature :125 °C; Rating :
2A /250V.
PAD07 is a security enabled wireless dimmer, based on Z-Wave Plus technology. ZWave PlusTM enabled devices displaying the Z-Wave PlusTM logo can also be used
with it regardless of the manufacturer, and can also be used in other manufacturer’s
Z-WaveTM enabled networks. You can On/Off the light by pressing the button briefly,
or a long pressing to control the brightness of dimmable light bulb.
This dimmer is a transceiver which is a security enabled device which based on
Warning: Do not use Non-Dimmable LED lamps.
Z-Wave Plus technology, and it is fully compatible with any Z-WaveTM enabled
network. Since PAD07 supports Security Command Class, it can learn with
Secured controller. Its functionality and supported command classes is identical
when included as a secure and non-secure device.
Adding to Z-WaveTM Network
In the front casing, there is an on/off button (also an include button) with LED indicator below which is used to dim on and off or carries out inclusion, exclusion, reset or
association. When first power applied, its LED flashes on and off alternately and repeatedly at 0.5 second intervals. It implies that it has not been assigned a node ID
and start auto inclusion.
Auto Inclusion
The function of auto inclusion will be executed as long as the dimmer does not
have Node ID and just connect the switch to main power.
Note: Auto inclusion timeout is 2 minute during which the node information of
explorer frame will be emitted once every several seconds. Unlike “inclusion” function
Fig 1. Assembling & Wiring
as shown in the table below, the execution of auto inclusion is free from pressing the
On/Off button on the dimmer.
Reset
1. Pressing Include button of PAD07
Use this procedure only in
The table below lists an operation summary of basic Z-Wave functions. Please refer
three times within 2 seconds will
the event that the primary
to the instructions for your Z-WaveTM Certificated Primary Controller to access the
enter inclusion mode.
controller is lost or
Setup function, and to Add/Remove/associate devices
2. Within 1 second, press Include button
otherwise inoperable.
of PAD07 again for 5 seconds.
Function
No node ID
Add (Inclusion)
Description
Annotation
The Z-Wave Controller does not allocate
LED 2-second on, 2-second
a node ID to the Switch.
off
1.
3. IDs are excluded.
auto inclusion)
Association
1.
Z-Wave device, so associations
inclusion mode by following the
may be added or removed by a con-
instructions provided by the
troller at any time.
Or If your controller requires to have
2. Pressing Include button of PAD07
1.
(Exclusion)
the PAD07 send a 'node information
three times within 2 seconds will
frame' or NIF for associations, then
enter inclusion mode.
pressing the On/Off button three
Put your Z-Wave controller into
times within 2 seconds will cause
exclusion mode by following the
the PAD07 to send its NIF.
instructions provided by the
2. There is only one group for the
controller manufacturer.
2.
The PAD07 is an always listening
Put your Z-Wave controller into
controller manufacturer.
Remove
dimmer
Adding a node ID allocated by Z-Wave Controller means inclusion. Removing a node
Pressing Include button of PAD07
three times within 2 seconds will
ID allocated by Z-Wave Controller means exclusion.
Failed or success in including/excluding the node ID can be viewed from the Z-Wave
enter exclusion mode.
3. Node ID has been excluded.
0.5s On, 0.5s Off (Enter
0.5s On, 0.5s Off (Enter
Controller.
auto inclusion)
LED Indication
To distinguish what mode the switch is in, view from the LED for identification.
S1/S2 shortly when the light is on. To adjust the dim level, press and hold the On/Off
button or S1/S2 until the desired dim level is achieved, then release.
State Type
LED Indication
Normal
Whenever we switch On and off of the PAD07 by On/Off button or RF
No node ID
Learning
command, the LED will lights up when switch on; whereas LED off
Programming
when switch off.
1. Basic Command Class / Multilevel Switch Command Class
Under normal operation, when the Switch has not been allocated a
The dimmer will respond to BASIC and MULTILEVEL SWITCH commands that are
node ID, the LED flashes on and off alternately at 2-second intervals.
part of the Z-Wave system. If PAD07 is included as a secured node, it will only re-
By pressing On/Off button, it will stop flashing temporarily.
sponse to the security encapsulation command of BASIC and MULTILEVEL
When PAD07 is in learning mode, LED flashes on and off alternately
SWITCH.
and repeatedly at 0.5 second intervals.
1-1 BASIC_GET / MULTILEVEL_SWITCH_GET
Upon receipt of the following commands from a Z-Wave Controller, the Switch will
report its dimmer state to the node inquired.
Basic Get Command: [Command Class Basic, Basic Get]
Choosing a Suitable Location
Basic Report Command:
1. Do not locate the dimmer facing direct sunlight, humid or dusty place.
Report OFF: [Command Class Basic, Basic Report, Value = 0]
2. The suitable ambient temperature for the Switch is 0°C~40°C.
Report ON:[Command Class Basic, Basic Report, Value = 1~99]
3. Do not locate the dimmer where exists combustible substances or any source of
Multilevel Switch Get Command:[Command Class Multilevel Switch, Multilevel
heat, e.g. fires, radiators, boiler etc.
Switch Get]
4. After putting it into use, the body of dimmer will become a little bit hot of which
phenomenon is normal.
Multilevel Switch Report Command:
Report OFF:[Command Class Multilevel Switch, Multilevel Switch Report,
Manual dim level control :
Value=0]
To manually switch on the light, press and release the On/Off button or S1/S2 shortly
Report ON:[Command Class Multilevel Switch, Multilevel Switch Report, Value
when the light is off. The light will dim from off to the level which was set before
=1~99]
switch off. To manually switch off the light, press and release the On/Off button or
Switch Report
1-2 BASIC_SET / MULTILEVEL_SWITCH _SET
Multilevel
Upon receipt of the following commands from a Z-Wave Controller, the load
ON:[Command Class Multilevel Switch, Multilevel Switch Report, Value
attached to the dimmer will turn on or off.
=1~99]
OFF:[Command Class Multilevel Switch, Multilevel Switch Report, Value
[Command Class Basic, Basic Set, Value = 0] : the load attached to the
=0(0x00)]
dimmer turns off.
2-1-2 Overload alarm report
[Command Class Basic, Basic Set, Value = 1~99] : the attached load dim on as
When PAD07 detects the Overload, it will send Alarm Report to Group 1 nodes. After
the level.
detecting overload state and sending this alarm report, PAD07 will turn off the dimmer automatically and lockout the On/Off button and S1/S2. The only thing to do is
[Command Class Multilevel Switch, Multilevel Switch Set, Value=0, Duration =
unplug PAD07 and reduce the load. Then re-power on PAD07 and it will work again.
0~255] : the load attached to the dimmer turns off.
The content of Alarm Report
[Command Class Multilevel Switch, Multilevel Switch Set, Value =1~99, Dura-
Alarm report command: [Command_Class_Alarm, Alarm_Report, Alarm Type =
tion = 0~255] : the attached load dim on as the level.
0x08, Alarm Level = 0xFF]
2-2 Send Basic Set to Grouping 1
1. Z-Wave’s Groups (Maximum 5 nodes)
When “on” or “off ” state has been changed by manual key pressing, a Basic Set
The Switch can be set to send reports to associated Z-Wave devices. It supports
command will follow the Multilevel Switch Report send to the nodes of Grouping 1.
one association group with five nodes support for grouping 1. For group 1, the dim-
[Command Class Basic, Basic Set, Value = 0]
mer
[Command Class Basic, Basic Set, Value = 1~99]
will report MULTILEVEL_SWITCH_REPORT, ALARM_REPORT and DEVICE_RE-
3. Z-Wave’s Configuration
SET_LOCALLY_NOTIFICATION.
Configuration
2-1 Auto report to Grouping 1
Parameter
2-1-1 On/Off Event Report
Function
Size
Value
Unit
Default
Description
0 : Disable
(Byte)
Dimmer Level
0-1
1 : Enable
When “on” or “off ” state has been changed, it will send Multilevel Switch Report to
Report mode
the
LED indication
1-3
1: Show dimmer state
2 : Show night mode
nodes of Grouping 1.
mode
3: One flash mode
3
External switch
1-3
could be Dimmer off、Last dimmer state、Dimmer on. The default setting is Last dim-
1 : One switch mode
2 : Two switch mode
type
mer state.
3: Up/Down switch
mode
Restore dimmer
0-2
0 : Dimmer off
4. Firmware update over the air (OTA)
1 : Last dimmer state
state
PAD07 is based on 500 series SoC and supports Firmware Update Command
2 : Dimmer on
Class, it can receives the updated firmware image sent by controller via the Zwave RF media. It is a helpful and convenient way to improve some function if
3-1 Dimmer level report mode :
needed.
Whenever dimmer on/off state changes, it will send MULTILEVEL_SWITCH_
REPORT to the nodes of group1. The default setting is Enable the function.
5. Command Classes
3-2 LED indication mode :
The Switch supports Command Classes including…
3-2-1 Show dimmer State：When dimmer is on, LED is on. When dimmer is off,
* COMMAND_CLASS_ZWAVEPLUS_INFO
LED is off. The default setting is Show dimmer State.
* COMMAND_CLASS_VERSION_V2
3-2-2 Show Night mode ： When dimmer is on, LED is off. When dimmer is off,
* COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
LED is on.
* COMMAND_CLASS_SECURITY
3-2-3 One flash mode：When dimmer on/off state changes, LED will light on one
* COMMAND_CLASS_DEVICE_RESET_LOCALLY
second and then off.
* COMMAND_CLASS_ASSOCIATION_V2
* COMMAND_CLASS_ASSOCIATION_GRP_INFO
3-3 External switch type：
* COMMAND_CLASS_POWERLEVEL
3-3-1 One switch mode：Only S1 can dim up the light bulb to brightest level, then
* COMMAND_CLASS_BASIC
dim down to darkest level, and so on…
* COMMAND_CLASS_SWITCH_MULTILEVEL_V2
3-3-2 Two switch mode：S1 and S2 can dim up the light bulb to brightest level,
* COMMAND_CLASS_CONFIGURATION
then dim down to darkest level, and so on…
* COMMAND_CLASS_ALARM
3-3-3 Up/Down switch mode：S1 can only dim up the light bulb to brightest level,
* COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
and S2 can only dim down to Off.
* COMMAND_CLASS_SCENE_ACTIVATION
3-4 restore dimmer state :
* COMMAND_CLASS_SCENE_ACTUATOR_CONF
Whenever the AC power return from lost, PAD07 will restore the switch state which
Specification
Troubleshooting
Input Rating:(Operating Voltage)
100~240Vac / 50Hz~60Hz
0.01~1A ; (Maximum: 1A)
Symptom
Cause of Failure
Recommendation
Input Rating:(Operating Current)
The dimmer does not
1.The dimmer does not
1. Check power connections
Output Rating: Maximum Load (Current) Maximum: 0.9A (100~240Vac)
2. Don’t open up the dimmer and send it for
Output Rating: Maximum Load (watts)
200W (13W x 15 pieces) (Dimmable LED bulbs)
(230V)
(230Vac)
Output Rating: Maximum Load (watts)
100W (13W x 15 pieces) (Dimmable LED bulbs)
(120V)
(120Vac)
work and LED off
connect the electrical
wire properly
repair.
2.The dimmer break down
The dimmer LED
Check if the load
Set the ON/OFF switch of the load attached
illuminating, but cannot
connected to the dimmer to ON
Output Rating: Maximum Dimmable LED Maximum: 15 pieces (Dimmable LED bulbs)
control the ON/OFF
has its own ON/OFF
bulbs
state of the load
switch
Operating Temperature
0°C ~ 40°C
Frequency Range
868.40MHz & 869.85MHz/ EU (PAD07-EU);
attached
The dimmer LED
illuminating, but the
1. Not carry out
association
1. Carry out association
908.4MHz & 916.0MHz/ USA (PAD07-US);
2. Wait for a while to re-try
Detector cannot control 2. Same frequency
the Switch
interference
RF Maximum Power
+5dBm
Transmission Range
Minimum 40 m in door 100m outdoor line of sight
Modulation Type
FSK (Frequency-Shift Keying)
** Specifications are subject to change and improvement without notice.
FCC ID : RHHPAD07
Disposal
Warning: Do not use Non-Dimmable LED lamps.
This marking indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent possible harm to
the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material
DANGER
Danger of electrocution!
resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was
All works on the device may be performed only by a qualified and licensed
purchased. They can take this product for environmental safe recycling.
electrician. Observe national regulations.
Any works introducing changes into the configuration must be always performed with
Company of License Holder：Philio Technology Corporation
disconnected voltage.
Address of License Holder：8F., No.653-2, Zhongzheng Rd., Xinzhuang Dist., New Taipei City
Choosing a Suitable Location
24257, Taiwan(R.O.C)
1. Do not locate the Module facing direct sunlight, humid or dusty place.
2. The suitable ambient temperature for the Module is 0°C~40°C.
FCC Interference Statement
3. Do not locate the Module where exists combustible substances or any source of
This equipment has been tested and found to comply with the limits for a Class B digital de-
heat, e.g. fires, radiators, boiler etc.
vice, pursuant to Part 15 of the FCC Rules.
4. After putting it into use, the body of Module will become a little bit hot of which
These limits are designed to provide reasonable protection against harmful interference in a
phenomenon is normal.
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to
Warning:
radio communications.
1.Plug out to disconnect from power supply; Do not plug in line.
However, there is no guarantee that interference will not occur in a particular installation.
2. Do not exceed the max rating.
If this equipment does cause harmful interference to radio or television reception, which
3. Do not use Non-Dimmable LED lamps.
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 8
Language                        : zh-TW
Creator                         : Writer
Producer                        : LibreOffice 5.0
Create Date                     : 2017:02:08 16:41:16+08:00

EXIF Metadata provided by EXIF.tools