Philio Technology PAN06 IN Wall Watch User Manual BH002 RF ON OFF CONTROLLER

Download:
Mirror Download [FCC.gov]
Document ID	2024406
Application ID	27xWa4XMzOjDfIZ/uuqlAw==
Document Description	(PAN06-2) UserMan
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	51.3kB (641221 bits)
Date Submitted	2013-07-24 00:00:00
Date Available	2013-07-25 00:00:00
Creation Date	2013-05-30 16:00:23
Producing Software	LibreOffice 4.0
Document Lastmod	0000-00-00 00:00:00
Document Title	BH002 RF ON/OFF CONTROLLER
Document Creator	Writer
Document Author:	.

PAN06-1/-2/-3 In Wall Dual relay(1 way) switch module
technology can reduce the inrush current caused by the load and let the module work perfectly with many
kind of light like incandescent, fluorescent and LED light. This module can also connect to alternative
power supply like DC 12V to switch on/off 12V MR-16 light as follow picture.
Adding to Z-WaveTM Network
In the front casing, there is an on/off button with LED indicator below which is used to
toggle switch on and off or carries out inclusion, exclusion, reset or association.
When first power is applied, its LED flashes on and off alternately and repeatedly at
2-second intervals. It implies that it has not been assigned a node ID and cannot
work with Z-Wave enabled devices.
Auto Inclusion
The function of auto inclusion will be executed as long as the in wall switch does not
have Node ID and just connect the switch to main power.
Fig 1. Assembling
Note: Auto inclusion timeout is 4 minute during which the node information of
This in-wall switch module is a transceiver which is a Z-WaveTM enabled device and is fully compatible
explorer frame will be emitted once every 5 seconds. Unlike “inclusion” function as
with any Z-WaveTM enabled network. Mini size design let the module can easily hide itself into the wall
shown in the table below, the execution of auto inclusion is free from pressing the
box and that will be good for the house decoration.
On/Off button on the Switch.
There are many kind of application by using the module to switch Load On and Off , one main application
is the light control. If connect the com port directly to AC Line terminal ,the new smart relay calibration
The table below lists an operation summary of basic Z-Wave functions. Please refer
Association
1.
to the instructions for your Z-WaveTM Certificated Primary Controller to access the
Have Z-Wave Controller entered
One press one flash
association mode.
Setup function, and to include/exclude/associate devices
Or Pressing Include button of PAN06
three times within 1.5 seconds will
Function
Description
LED Indication
No node ID
The Z-Wave Controller does not allocate
2-second on, 2-second off
enter association mode
2. There are 3 groups for the switch
a node ID to the Switch.
Inclusion
1.
Have Z-Wave Controller entered
※Including a node ID allocated by Z-Wave Controller means inclusion.
One press one flash
inclusion mode.
Excluding a node
ID allocated by Z-Wave Controller means exclusion.
※Failed or success in including/excluding the node ID can be viewed from the Z-Wave
2. Pressing Include button of PAN06
three times within 1.5 seconds will
Controller.
enter inclusion mode.
Exclusion
1.
2.
Have Z-Wave Controller entered
One press one flash
Sometimes people are not easy to execute exclusion or inclusion especially when
exclusion mode.
PAN06 already installed in a wall box. To solve this issue, PAN06 support a special
Pressing Include button of PAN06
feature that can use S1 or S2 to execute “exclusion, inclusion, Reset or Association”
three times within 1.5 seconds will
at the first 3 minutes when first time connect to main power.
enter exclusion mode.
Reset
1.
Node ID has been excluded.
2-second on, 2-second off
LED Indication
Pressing Include button of PAN06
One press one flash
To distinguish what mode the switch is in, view from the LED for identification.
three times within 1.5 seconds will
2.
3.
enter inclusion mode.
State Type
LED Indication
Within 1 second, press Include
Normal
Whenever we switch On and off of the PAN06 by S1 S2 or On/Off
button of PAN06 again for 5
button or RF command , the LED will lights up 1 second and then
seconds until LED is off.
off.
IDs are excluded.
2-second on, 2-second off
No node ID
Under normal operation, when the Switch has not been allocated a
node ID, the LED flashes on and off alternately at 2-second
intervals. By pressing S1 S2 or On/Off button, it will stop flashing
temporarily. However, after disconnect and reconnect the Switch,
the LED will flash on and off alternately at 2-second intervals.
Choosing a Suitable Location
1. Do not locate the Switch facing direct sunlight, humid or dusty place.
1. Put the in wall switch into a wall box and connect the AC power wire L,N to
2. The suitable ambient temperature for the Switch is 0°C~40°C.
PAN06 connector L, N.
3. Do not locate the Switch where exists combustible substances or any source of
2. Connect the wall switch to the PAN06 as Fig1 .
heat, e.g. fires, radiators, boiler etc.
3. There are 3 mode PAN06 can be configured to match different kind of wall
4. After putting it into use, the body of Switch will become a little bit hot of which
switch, please refer to 3-2 Edge / Pulse / Edge-Toggle mode which described
phenomenon is normal.
in next section of this user manual
4. If Edge-Toggle mode has been set, and the S1 S2 is connect to normal bi-stable
Installation
switch, every time when change the state of the wall switch will also swap the
state of Relay1 or Relay2
Programming
1. Basic Command Class / Binary Switch Command Class
The Switch will respond to BASIC and BINARY commands that are part of the ZWave system.
1-1 BASIC_GET / BINARY_SWITCH_GET
Since the switch have two relay, the Switch will report its On/Off state to the
Controller by setting Configuration parameter 1.
Configuration parameter 1=1(default) Report ON either relay 1 ON or relay 2
ON
Report OFF when both relay 1 and relay 2 OFF
Configuration parameter 1=2 switch ON and OFF of relay 1
Configuration parameter 1=2 Report ON when relay 1 ON
Report OFF when relay 1 OFF
Configuration parameter 1=3 switch ON and OFF of relay 2
Configuration parameter 1=3 Report ON when relay 2 ON
Report OFF when relay 2 OFF
Basic Get Command: [Command Class Basic, Basic Get]
[Command Class Basic, Basic Set, Value = (255)0xFF]: the load attached to
Basic Report Command:
the Switch turns on.
Report OFF: [Command Class Basic, Basic Report, Value = 0(0x00)]
[Command Class Basic, Basic Set, Value = 0(0x00)]: the load attached to
Report ON:[Command Class Basic, Basic Report, Value = (255)0xFF]
the Switch turns off.
[Command Class Switch Binary, Switch Binary Set, Value = (255)0xFF]:
Binary Switch Get Command:[Command Class Switch Binary, Switch
the load attached to the Switch turns on.
Binary Get]
[Command Class Switch Binary, Switch Binary Set, Value = 0(0x00)]: the
Binary Switch Report Command:
load attached to the Switch turns off.
Report OFF:[Command Class Switch Binary, Switch Binary Report, Value
=0(0x00)]
2. Z-Wave’s Groups (Association Command Class Version 1)
Report ON:[Command Class Switch Binary, Switch Binary Report, Value =
(255)0xFF]
The Switch can be set to send reports to control associated Z-Wave devices. It
supports 3 association groups which every group has one node support.
Group1~Group3 support SWITCH_BINARY_REPORT.
1-2 BASIC_SET / SWITCH_BINARY_SET
Since the switch have two relay, the load attached to the Switch will turn on or
off upon receipt of the following commands from a Z-Wave Controller by setting
For group 1, the Switch will report ON/OFF status of Relay1 and Relay2
Configuration parameter 1.
For group 2, the Switch will report ON/OFF status of Relay1
For group 3, the Switch will report ON/OFF status of Relay2
2-1 Auto report to Grouping 1 ~3(Maximum Node 1)
Configuration parameter 1=1(default) switch ON and OFF both relay 1 and
relay 2
2-1-1 On/Off Event Report
COMMAND_CLASS_MULTI_CHANNEL
When “on” or “off ” state has been changed (ex. Press S1 S2 or include on/off
MULTI_CHANNEL_CMD_ENCAP
button), it will send Binary Switch Report to the nodes of Group1~3.
Source End Point = 0x05
(this is the endpoint of command owner
here we assume endpoint is 5，if
Binary Switch Report
the owner doesn’t support multi
Channel this value will be 0)
ON:[Command Class Switch Binary, Switch Binary Report, Value
(Bit Address+Destination End Point = 0x01) (Bit Address =0；Destination End Point
=(255)0xFF]
range from 1~3)
OFF:[Command Class Switch Binary, Switch Binary Report, Value
=0(0x00)]
Command Class = 0x25
(Command_Class_Switch_Binary =
0x25)
Command =0x02
2-2 Multi Channel Command Class Version 3
(Switch_Binary_Get = 0x02)
Below is the example show PAN06 report to last command
PAN06 also support muti channel command class(version 3) , which include
COMMAND_CLASS_MULTI_CHANNEL
BINARY_SWITCH_GET, BINARY_SWITCH_SET
MULTI_CHANNEL_CMD_ENCAP
You may control or get report from 3 endpoint of PAN06
2-2-1 BINARY_SWITCH_GET,
Source End Point = 0x01
Since the endpoint is 1 so PAN06 will
reply ON(0xFF) either Relay 1 or Relay2
You may get the ON/OFF state from every endpoint, when endpoint set to 1 ,
PAN06 will reply ON(0xFF) either Relay 1 or Relay2 is ON, report OFF (0x00)
is ON, report OFF (0x00) when both
when both Relay 1 and Relay2 OFF . If endpoint set to 2 , PAN06 will reply
Relay 1 and Relay2 OFF
state of Relay1 . If endpoint set to 3 and PAN06 will reply state of Relay2
(Bit Address+Destination End Point = 0x05) (Bit Address =0；Destination End Point)
Below is a example show a source endpoint 5 send a get command to PAN06
endpoint 1
Command Class = 0x25
(Command_Class_Switch_Binary =
0x25)
Command =0x03
(Switch_Binary_Report = 0x03)
3. Z-Wave’s Configuration
Parameter 1 = 0xFF
(ON=0xFF ， OFF=0x00)
Configuration
2-2-2 BINARY_SWITCH_SET
Function
Parameter
By using BINARY_SWITCH_SET Command of Multi Channel Command Class
Encapsulation Command, you can switch both Relay1 and Relay2 ON/OFF by
Size
Value
Unit
Default
Description
1：Relay1 &
(Byte)
Slected
1-3
End Point
setting endpoint to 1 or switch Relay1 ON/OFF by setting endpoint to 2 or switch
Relay2
2：Relay1
Relay2 ON/OFF by setting endpoint to 3
3：Relay2
The example of the command show that switch off relay1 of PAN06
Edge or
1-3
Pulse
COMMAND_CLASS_MULTI_CHANNEL
2：Pulse mode
mode or
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x01
3：Edge-Toggle
mode
Edge(this is the endpoint of command owner
Toggle
here we assume endpoint is 1，if the
mode
1：Edge mode
owner doesn’t support multi Channel this
value will be 0)
3-1 Selected Endpoint
(Bit Address+Destination End Point = 0x02) (Bit Address =0；Destination End Point
If Controller not using Multi_Channel command class to access the endpoint of
range1~3)
PAN06, you may configure the endpoint value to react the Basic Command Class
Command Class = 0x25
(Command_Class_Switch_Binary =
or Binary Switch Command Class.
0x25)
Command =0x01
Parameter 1 = 0x00
3-1-1 Selected Endpoint 1： Default Selected Endpoint is 1
(Switch_Binary_Set = 0x01)
(ON=0xFF ， OFF=0x00)
Set command
Relay state
Basic Set or Binary_Switch_Set ON
Relay1
ON
Edge-Toggle mode: this mode is suitable for the normal bi-stable switch, every time
Relay2 ON
Basic Set or Binary_Switch_Set OFF
Relay1
OFF
when change the state of the wall switch will also swap the state of Relay1 or Relay2
Relay2 OFF
Get command
Relay state
Basic_Get or Binary_Switch_Get
Relay1
ON
4. Command Classes
Report to command sender
or ON
The Switch supports Command Classes including…
Relay2 ON
Basic_Get or Binary_Switch_Get
* COMMAND_CLASS_SWITCH_BINARY
Relay1 OFF & OFF
* COMMAND_CLASS_BASIC
Relay2 OFF
* COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
3-1-2 Selected Endpoint 2
* COMMAND_CLASS_VERSION
Similar like Selected Endpoint 1 but only relate to Relay1 and ignore Relay2
* COMMAND_CLASS_SWITCH_ALL
3-1-3 Selected Endpoint 3
* COMMAND_CLASS_ASSOCIATION_V1
* COMMAND_CLASS_CONFIGURATION
Similar like Selected Endpoint 1 but only relate to Relay2 and ignore Relay1
* COMMAND_CLASS_MULTI_CHANNEL_V3
3-2 Edge / Pulse / Edge-Toggle mode
* COMMAND_CLASS_ALARM
Manual switch S1 and S2 can set to Edge mode or Pulse mode or Edge-Toggle
mode , default value is Edge mode.
Edge mode: this mode is suitable for the bi stable wall switch that has indicator point
Troubleshooting
on the switch, and the same position correspond to same state of relay1 and relay2 .
if the PAN06 relay change the state because of receiving Z-Wave RF command, it
may need two times of change (switch on to off or switch off to on) to let relay back
Symptom
to the correspond state.
The Switch not working and 1. The Switch is not
1. Check power connections
LED off
2. Don’t open up the Switch and
Pulse mode: this mode is suitable for the toggle type wall switch to swap the state of
Cause of Failure
connect to the Main
power
Relay1 or Relay2
2. The Switch break
down
Recommendation
send it for repair.
The Switch LED
Check if the load connect Set the ON/OFF switch of the load
illuminating, but cannot
into the Switch has its
control the ON/OFF
own ON/OFF switch
attached to ON
Warning:
1.Plug out to disconnect from power supply; Do not plug in line.
Switch of the load attached
The Switch LED
2. Do not exceed the max rating
1. Not carry out
illuminating, but the
association
Detector cannot control
1. Carry out association
Disposal
2. Wait for a while to re-try
This marking indicates that this product should not be disposed with
2. Same frequency
the Switch
other household wastes throughout the EU. To prevent possible harm to
interference
Remove the load attached or check
the environment or human health from uncontrolled waste disposal,
continuously, but cannot
max. load cannot exceed
recycle it responsibly to promote the sustainable reuse of material
control
1500W~1650W
resources. To return your used device, please use the return and
LED keep flashing
Overload occurs
collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recycling.
Specification
Operating Voltage
100 ~240VAC
Company of License Holder：Philio Technology Corporation
24-60V DC ±10%
Address of License Holder：8F.,No.653-2,Zhongzheng Rd., Xinzhuang Dist., New
Taipei City 24257,Taiwan(R.O.C)
Maximum Load
1500W X2 (220V) 800W X 2 (120V)
Range
Minimum 30 m in door 100m outdoor line of sight
Operating Temperature 0°C ~ 40°C
FCC Interference Statement
Frequency Range
PAN06-1 868.42 (EU) / PAN06-2 908.42(USA/Canada) / PAN06-3
This equipment has been tested and found to comply with the limits for
922.5/923.9/926.3MHz (Taiwan/JP)MHz
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
** Specifications are subject to change and improvement without notice.
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
FCC ID : RHHPAN06
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.
This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 9
Language                        : zh-TW
Title                           : BH002  RF ON/OFF CONTROLLER
Author                          : .
Creator                         : Writer
Producer                        : LibreOffice 4.0
Create Date                     : 2013:05:30 16:00:23+08:00

EXIF Metadata provided by EXIF.tools