Proxim Wireless AP8100 Wireless 802.11 abgn Router User Manual ORiNOCO AccessPoints HardwareInstGuide
Proxim Wireless Corporation Wireless 802.11 abgn Router ORiNOCO AccessPoints HardwareInstGuide
Contents
- 1. User Manual
- 2. User Manual - Statements
- 3. User manual rev
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1786113 |
| Application ID | AjPuba3lVY2p9Uz/5r7aQg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 169.76kB (2121959 bits) |
| Date Submitted | 2012-09-07 00:00:00 |
| Date Available | 2012-09-07 00:00:00 |
| Creation Date | 2012-08-16 10:56:04 |
| Producing Software | Acrobat Distiller 8.0.0 (Windows) |
| Document Lastmod | 2012-09-04 11:52:02 |
| Document Title | ORiNOCO_AccessPoints_HardwareInstGuide.book |
| Document Creator | FrameMaker 8.0 |
| Document Author: | nsuri |
ORiNOCO® 802.11n Access Points Hardware Installation Guide Products Covered ORiNOCO® AP-800 ORiNOCO® AP-8000 ORiNOCO® AP-8100 Copyright © 2012 Proxim Wireless Corporation, Milpitas, CA. All rights reserved. Covered by one or more of the following U.S. patents: 5,231,634; 5,875,179; 6,006,090; 5,809,060; 6,075,812; 5,077,753. This guide and the software described herein are copyrighted with all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of Proxim Wireless Corporation. Trademarks ORiNOCO® and the Proxim logo are the trademarks of Proxim Wireless Corporation. All other trademarks mentioned herein are the property of their respective owners. Disclaimer Proxim reserves the right to revise this publication and to make changes in the content from time-to-time without obligation on the part of Proxim to provide notification of such revision or change. Proxim may make improvements or changes in the product(s) described in this guide at any time. When using these devices, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons. ORiNOCO® 802.11n Access Points - Hardware Installation Guide Documentation Version: 4.1 P/N 765-00154, September 2012 ORiNOCO® 802.11n Access Points - Hardware Installation Guide Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 About ORiNOCO® 802.11n Access Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Salient Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Multiple-Input-Multiple-Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Hardware Overview and Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 ORiNOCO® AP-800 and AP-8000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Product Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 ORiNOCO® AP-8100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Front View of the Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear View of the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 16 17 17 18 Hardware Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 ORiNOCO® AP-800 and AP-8000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 ORiNOCO® AP-8100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Glossary and Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Statement of Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Technical Services and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 ORiNOCO® 802.11n Access Points - Hardware Installation Guide Preface Preface This chapter contains information on the following: • About this Guide • Products Covered • Audience • Prerequisites • Documentation Conventions • Related Documents About this Guide This guide gives a jump start working knowledge on the ORiNOCO® 802.11n Access Points and details on their hardware specifications and installation procedures. Products Covered Listed below are the products covered in this guide: • ORiNOCO® AP-800 • ORiNOCO® AP-8000 • ORiNOCO® AP-8100 Audience The intended audience for this guide are the network administrators who installs and/or manages the device. Prerequisites The reader of this guide should have working knowledge of Wireless Networks, Local Area Netowrking (LAN) concepts, Network Access Infrastructures and Client-Server Applications. Documentation Conventions Icon Representation Name Image Description Note A special instruction that draws attention of the user. Important A note of significant importance that a user should be aware of. Caution A warning that cautions the user of a possible danger. ORiNOCO® 802.11n Access Points - Hardware Installation Guide Preface Related Documents For more information, please refer to the following additional documents that are available at proxim’s support site http://support.proxim.com. • Quick Installation Guide (QIG) - A quick reference guide that provides essential information to install and configure the device. • Software Management Guide - A guide that provides instructions on how to configure, manage and monitor the device by using Web Interface. • Reference Guide - A guide that provides instructions on how to configure, manage and monitor the device by using Command Line Interface. • Safety and Regulatory Compliance Guide - A guide that provides country specific safety and regulatory norms to be followed while installing the devices. : For regulatory information and latest product updates, visit our support site http://support.proxim.com. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 1 Introduction This chapter contains information on the following: • About ORiNOCO® 802.11n Access Points • Salient Features • Multiple-Input-Multiple-Output 1.1 About ORiNOCO® 802.11n Access Points Proxim’s ORiNOCO® 802.11n Access Point family comprises the following products, that are designed to deliver flexible, scalable and reliable Data, Voice, and Video for small and medium Enterprise WLAN deployments. Product(s) Description ORiNOCO® AP-800 An indoor 802.11n Access Point with dual-band, 3x3 MIMO (Multiple Input and Multiple Output) single radio which operates either in 2.4 or 5 GHz. This connectorized unit comes with 3 omni-directional antennas. ORiNOCO® AP-8000 An indoor 802.11n Access Point with dual-band, 3x3 MIMO (Multiple Input and Multiple Output) dual-radio, where one operates in 5GHz and other in 2.4GHz. This connectorized unit comes with 6 omni-directional antennas, 3 per radio. ORiNOCO® AP-8100 An indoor 802.11n Access Point with 2x2 MIMO (Multiple Input and Multiple Output) dual-radio, where one operates in 5GHz and other in 2.4GHz. This unit comes with 4 integrated antennas, 2 per radio. Image 1.2 Salient Features • Industry-leading throughput in 802.11b/g/n and 802.11a/n modes in 2.4GHz and 5GHz respectively. • Highest throughput with single radio rates of 150 - 170 Mbps and dual radio rates of 250 - 320 Mbps. • Advanced WPA/WPA2 support for enterprise-grade security. • Wi-Fi certified to interoperate with any Wi-Fi certified client access product. • Provides wall or ceiling mounting options for flexible device installation. • Centralized Management with distributed WLANs. • Management through a Web Interface (HTTP), Command Line Interface (CLI), Simple Network Management Protocol (SNMP) and Network Management System (ProximVision ES v2.3 and above). : Managing the device through Network Management System (ProximVision ES) is applicable only to AP-800 and AP-8000. ORiNOCO® 802.11n Access Points - Hardware Installation Guide Introduction 1.3 Multiple-Input-Multiple-Output ORiNOCO® Access Point devices support Multiple-Input-Multiple-Output (MIMO) antenna technology that uses multiple antennas at both the transmitting end and receiving end to improve communication performance. The underlying technology of these access point radio(s) are based on a combination of MIMO and OFDM (Orthogonal Frequency Division Multiplexing). MIMO-OFDM combination radios solve interference, fading and multipath problems. Having multiple receivers at the receiving end, increases the amount of received power and also reduces multipath problems by combining the received signals for each frequency component separately. Hence, MIMO significantly improves the overall gain. MIMO also uses Spatial multiplexing transmission technique to transmit independent and separately encoded data signals from each of the multiple transmit antennas while reusing or multiplexing in the space dimension. These independent data signals are called Spatial streams. The transmitting end of the device uses multiple radio Tx chains and signal paths to simultaneously transmit different data streams, whereas the receiving end combines the Rx signals resulting in higher throughput. By increasing the number of receiving and transmitting antennas, the throughput of the channel increases linearly resulting in high spectral efficiency. ORiNOCO® 802.11n Access Points - Hardware Installation Guide Hardware Overview and Installation This chapter covers the hardware overview and installation procedures of the following products: • ORiNOCO® AP-800 and AP-8000 — Hardware Overview — System Requirements — Product Package — Installation Procedure • ORiNOCO® AP-8100 — Front View of the Device — Rear View of the Device — System Requirements — Product Package — Installation Procedure • All the interface (radio) 2 parameters discussed in this chapter are applicable only to a dual-radio device. • For a quick reference on how to install and mount the device, please refer to the ORiNOCO® AP-800, AP-8000, and AP-8100 Quick Installation Guides respectively. ORiNOCO® 802.11n Access Points - Hardware Installation Guide Hardware Overview and Installation 2.1 ORiNOCO® AP-800 and AP-8000 2.1.1 Hardware Overview ORiNOCO® AP-800 ORiNOCO® AP-8000 Figure 2-1 Device Overview Following sections give you hardware overview of AP-800 and AP-8000. 2.1.1.1 LED Indicators Tabulated below are the four LEDs, that are available on the top panel of the device: LED Symbol Description Power LED This LED indicates whether the device is switched on/off. Ethernet LED This LED signals the traffic on the wired ethernet LAN. Wireless Interface (Radio) 1 LED This LED provides the status of the traffic on wireless interface (radio) 1. Wireless Interface (Radio) 2 LED This LED provides the status of the traffic on wireless interface (radio) 2. 2.1.1.2 Antennas The AP device comes with 3x3 MIMO omni-directional antennas that are easy to install. Proxim also recommends you an optional accessory - Range Extender Antenna (REA) with a 3 x RP SMA plug, that can be easily connected to the device. See Installation Procedure, for details on installation of antennas. – AP-800 comes with three omni directional antennas. – AP-8000 comes with six omni directional antennas, three per radio. ORiNOCO® 802.11n Access Points - Hardware Installation Guide Hardware Overview and Installation Antenna Ports Top View of the Device Bottom View of the Device If you hold the AP device in its upright position, such that the LEDs on the top panel of the device are towards your right hand side and the ‘Proxim’ logo towards your left, then: – Radio 1 and its corresponding antenna ports (R1A1, R1A2 and R1A3), are present on the right hand side of the device. – Radio 2 and its corresponding antenna ports (R2A1, R2A2 and R2A3), are present on the left hand side of the device. 2.1.1.3 Power Socket This socket connects to the 5 VDC power adapter. 2.1.1.4 Reset Reset button enables a user to powercycle the device. 2.1.1.5 Reload Reload feature helps to restore the device to factory default configuration, when: – The device cannot be accessed through web interface or command line interface. – The device does not initialize. – The password is lost. For more details, see Recovery Procedures and Forced Reload procedures, detailed in the ORiNOCO® 802.11n Access Points Software Management Guide. 2.1.1.6 Ethernet Port The Ethernet Port of the device allows the user to connect to the LAN by using CAT5e / CAT6 ethernet cable. 2.1.1.7 Serial Port The device has RS-232 connector by using which serial communication can be established, for debugging and management. Figure 2-2 Rear View of the Device ORiNOCO® 802.11n Access Points - Hardware Installation Guide 10 Hardware Overview and Installation 2.1.2 System Requirements Following are the minimum system requirements to use the device: 1. Any 802.11 compliant wireless adapter. 2. A computer that is connected to the same IP network as the AP and has one of the following installed: — Web Browser — Telnet — RS-232 Serial Port — MIB Browser — Ethernet NIC Card 3. Ethernet switch, cross-over or straight Ethernet cable. 4. A 5V DC Power Adapter or a Power over Ethernet (PoE) Adapter 2.1.3 Product Package Each shipment includes the items listed in the following table. Please verify that you have received all the parts in the shipment, prior to the installation. What’s in the Kit Image ORiNOCO® AP-800 or AP-8000 OR Omni-directional Antennas with reverse SMA connectors. • AP-800 : Quantity - 3 • AP-8000: Quantity - 6 Cable Security Cover Mounting Kit Quick Installation Guide (QIG) ORiNOCO® 802.11n Access Points - Hardware Installation Guide 11 Hardware Overview and Installation 2.1.3.1 Optional Accessories Tabulated below are the recommended optional accessories, that are supplied on request from Proxim Wireless Corporation. Accessory Image 110-220V worldwide Power Adapter Range Extender Antenna (REA) Gigabit Ethernet PoE 2.1.4 Installation Procedure Perform the following steps to install and mount the device. 2.1.4.1 Step 1: Install the Antennas The omni-directional antennas supplied with the product do not require any professional installation. Only, the regular outdoor antennas connected via a pigtail conversion cable, offering a standard connector type for antenna connection, require a professional installation. : Optionally, you can use the Range Extended Antenna (REA), which has 3 x RP SMA plug, that can be easily connected to the device. Perform the following steps to assemble the antennas: 1. Hand-tighten the antennas clockwise, onto the external connectors of the device until they are attached firmly. 2. Position the antennas close to the horizontal surface (ceiling or wall), so as to get the maximum signal coverage of the omni-directional antenna. 2.1.4.2 Step 2: Mount the Device Consider the following precautions, before mounting the device: • The device must be protected from exposure, and the environmental conditions must be within those specified in the product datasheet, that can be found at http://support.proxim.com. • Ensure to use a +5V/3.5 A power adapter, to power on the device. • Note that the device is build with fire retardant ATX200 resin and can be installed in the plenum. In an office building, plenum is the space between the structural ceiling and the tile ceiling that is provided to help air circulate. Many companies also use the plenum to house communication equipment and cables. These products and cables must comply with certain safety requirements, such as Underwriter Labs (UL) and Standard 2043: “Standards for Fire Test for Heat and Visible Smoke Release for Direct Products and Their Accessories installed in Air-Handling Spaces”. • When installed in a plenum, the device must use PoE. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 12 Hardware Overview and Installation Conduct a site survey to determine the best location for the device. You can either mount the device to a wall or mount it to the T-bar ceiling, as follows: Wall-Mounting: To mount the device to a wall, follow the following steps: 1. If the device is powered on, unplug all the power cables. 2. Place the mounting plate on the wall with the embossed inverted letter “L” facing your right, as shown below: Figure 2-3 Mounting Plate 3. Fasten the mounting plate by using a pair of plastic anchors and screws provided with the product package. 4. Hold the device with its rear panel facing up. Next, align two keyholes on the device with the two holders on the mounting plate. 5. Carefully slide the device down until the holders on the mounting plate fasten securely onto the keyholes of the device. Figure 2-4 Mount the Device Ceiling Mounting: To mount the device to ceiling, follow the following steps: 1. If the device is powered on, unplug all the power cables. 2. Place the mounting plate onto the ceiling with the embossed inverted letter “L” facing your right. Refer Mounting Plate 3. Fasten the mounting plate by using a pair of plastic anchors and screws provided with the product package. 4. Hold the device with its rear panel facing front. Next, align two keyholes on the device with the two holders on the mounting plate. 5. Carefully slide the device towards rear side until the holders on the mounting plate fasten securely onto the keyholes of the device. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 13 Hardware Overview and Installation 2.1.4.3 Step 3: Plugging in the Cables Cabling with Power Adapter (Not supplied with the product package) To plug in the cables by using a 5V DC power adapter: • Connect one end of the CAT5e/CAT6 Ethernet cable (not supplied with the product) to the device’s ethernet port and the other end to a PC. • Plug the barrel of the power cable into the device’s power socket, only after the device installation is complete. Cabling with Gigabit PoE (Not supplied with the product package) To use Power over Ethernet (PoE), we recommend you to use our Gigabit Ethernet PoE adapter ORiNOCO 1-Port Active Ethernet DC Injector (See Optional Accessories) and follow the following guidelines: • Connect one end of the ethernet cable to the Data In port of the DC Injector and the other end to a PC. • Connect one end of the second ethernet cable (not supplied with the product) to the device’s ethernet port, and the other end to the Data & Power Out Port of the DC Injector, only after the device installation is complete. : PoE should be installed only in an indoor network, maintaining a controlled temperature. Serial Connection Optionally, you can connect a nine-pin, male-to-female serial cable to the console port/DB9 connector of the device for debugging and management. • Use a straight-through ethernet cable, if you intend to connect the device to a switch, hub, or patch panel. • Use a cross-over ethernet cable or adapter if you intend to connect the device to a single computer. • The pin6 on RJ11 connector is used for power consumption and debugging. This connects internally to the 12VDC. • If power is drawn from this input pin, then the radio might malfunction. 2.1.4.4 Step 4: Power On the Device To power on the device, plug in the power cord into a power outlet. There is no ON/OFF switch on the device. To disconnect power: • Unplug the RJ45 connector from the Data & Power Out port on the DC injector, if using the Gigabit Ethernet PoE. • Unplug the power cable from the power socket of the device, if using power adapter. 2.1.4.5 Step 5: View LEDs When the device is powered on, it performs startup diagnostics. When startup is complete, the LEDs show the operational state of the device. Tabulated below is the behavior of the four LEDs on the device: LED Power LED Ethernet LED Behavior Color Glows green when the device is switched ON. Glows red when the ethernet interface is connected to a 100 Mbps link. Glows green when the ethernet interface is connected to a 1000 Mbps link. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 14 Hardware Overview and Installation Wireless Interface (Radio) 1 LED • The Wireless LEDs glow steady green in operational status. • Blinks green, if wireless traffic is being transmitted or received. Wireless Interface (Radio) 2 LED : The LEDs glow ‘orange’ when the device initializes. 2.1.4.6 Step 6: Install Cable Security Cover (Optional) When the RS-232 cable is not connected, we recommend you to install a cable security cover to prevent the power socket, LAN ports, reset and reload buttons from getting tampered. Follow the following procedure to install the cable security cover: 1. Open the split end of the security cover just enough to slide the power cable (if the Gigabit Ethernet PoE is not used) and the CAT6 ethernet cable through the opening until they fit inside the straight clamping portion of the cover. 2. Exercise care, as you slide the cable(s) so that you do not accidently break the cover. 3. Slide the hinging end of the security cover and insert the latch into the hole at the rear end of the device. 4. Insert the two screws into the screw holes near serial port and fasten the security cover on the device. 2.2 ORiNOCO® AP-8100 2.2.1 Front View of the Device Figure 2-5 Front View of the Device The front panel of the device contains the following components: 2.2.1.1 LED Indicators Tabulated below are the four LEDs, that are available on the front panel of the device: LED Symbol Description Power LED This LED indicates whether the device is switched ON/OFF. Ethernet LED This LED indicates the status of the traffic over the wired ethernet LAN. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 15 Hardware Overview and Installation 2.4G (Wireless Interface 2) LED This LED indicates the status of the traffic over the wireless interface (radio) 2. 5G (Wireless Interface 1) LED This LED indicates the status of the traffic over the wireless interface (radio) 1. 2.2.1.2 Reload Reload button helps to restore the device to factory default configuration, when: – The device cannot be accessed through web interface or command line interface. – The device does not initialize. – The password is lost. To avoid tampering, you can lock the reload button on the device and disable the reload functionality. For more details, refer to the Reload feature and Recovery Procedures illustrated in ORiNOCO® 802.11n Access Points - Software Management Guide. 2.2.2 Rear View of the Device Figure 2-6 Rear View of the Device The rear panel of the device contains the following components: 2.2.2.1 Ethernet Port The Ethernet port of the device allows the user to connect to the LAN by using CAT5e / CAT6 ethernet cable. 2.2.2.2 Power Socket This socket connects to the 12 VDC power adapter. 2.2.2.3 Keyhole A provision to fix the device onto the mounting plate. 2.2.2.4 Kensington Lock A security slot to lock the device. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 16 Hardware Overview and Installation 2.2.2.5 Cable Route A slot for the CAT5e / CAT6 ethernet cable and the power cable to rest securely. 2.2.2.6 Vent-Holes Ventilation holes on the device allow heat dissipation. 2.2.3 System Requirements Following are the minimum system requirements to use the device: 1. Any 802.11 compliant wireless adapter. 2. A computer that is connected to the same IP network as the AP and has one of the following installed: — Web Browser — Telnet — MIB Browser — Ethernet NIC Card 3. Ethernet switch, cross-over or straight Ethernet cable. 4. A 12V DC Power Adapter or a Power over Ethernet (PoE) Adapter. 2.2.4 Product Package Each shipment includes the items listed in the following table. Please verify that you have received all the parts in the shipment, prior to the installation. What’s in the Kit Image ORiNOCO® AP-8100 Mounting Kit Power Adapter (Supplied with country specific plug) * Supplied only with the WD SKU. Quick Installation Guide (QIG) ORiNOCO® 802.11n Access Points - Hardware Installation Guide 17 Hardware Overview and Installation 2.2.4.1 Optional Accessories Tabulated below are the recommended optional accessories, that are supplied on request from Proxim Wireless Corporation. Accessory Part Number PoE Adapter (US/CAN/JP Power Cord) 76282 PoE Adapter (EU Power Cord) 76288 PoE Adapter (UK Power Cord) 76287 Image Description PoE module helps you to power ON the device via ethernet cabling. 2.2.5 Installation Procedure Perform the following steps to mount and install the device. 2.2.5.1 Step 1: Plugging in the Cables Cabling with Power Adapter (Supplied with the product package) To plug in the cables by using a 12V DC power adapter: • Connect one end of the CAT5E/CAT6 Ethernet cable to the device’s ethernet port and the other end to a PC. • Plug the barrel of the power cable into the device’s power socket, only after the device installation is complete. : Use a cable-tie to ensure that the power cable stays intact with the device power socket. Cabling with Gigabit PoE (Not supplied with the product package) To use Power over Ethernet (PoE), we recommend you to use our Gigabit Ethernet PoE adapter ORiNOCO 1-Port Active Ethernet DC Injector (See Optional Accessories) and follow the following guidelines: • Connect one end of the ethernet cable to the Data In port of the DC Injector and the other end to a PC. • Connect one end of the second ethernet cable to the device’s ethernet port, and the other end to the Data & Power Out Port of the DC Injector, only after the device installation is complete. : PoE should be installed only in an indoor network, maintaining a controlled temperature. 2.2.5.2 Step 2: Mount the Device Consider the following precautions, before mounting the device: • The device must be protected from exposure, and the environmental conditions must be within those specified in the product datasheet that can be found at http://support.proxim.com. • Ensure to use a +12V/1.25 A power adapter, to power on the device. • Ensure that there is no power supply, until the device installation is complete. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 18 Hardware Overview and Installation • Note that the device is build with fire retardant ATX200 resin and can be installed in the plenum. In an office building, plenum is the space between the structural ceiling and the tile ceiling that is provided to help air circulate. Many companies also use the plenum to house communication equipment and cables. These products and cables must comply with certain safety requirements, such as Underwriter Labs (UL) and Standard 2043: “Standards for Fire Test for Heat and Visible Smoke Release for Direct Products and Their Accessories installed in Air-Handling Spaces”. • When installed in a plenum, the device must use PoE. Conduct a site survey to determine the best location for the device. You can either mount the device to a wall or mount it to the T-bar ceiling, as follows: Wall-Mounting: To mount the device to a wall: 1. Place the mounting plate on the wall such that the embossed letter ‘L’ is at the top-center position and the vent-holes are facing your left hand side. Figure 2-7 Mounting Plate 2. Fasten the mounting plate by using a pair of plastic anchors and screws provided with the product package. 3. Hold the device in the upright position (with ‘Reload’ on top and the ‘LEDs’ at the bottom), such that the vent-holes on the device and the vent-holes on the mounting plate rest on each other. 4. Align the two keyholes on the device with the two holders on the mounting plate. 5. Carefully, slide the device towards your right hand side, until the holders on the mounting plate fasten securely onto the keyholes of the device. Figure 2-8 Wall Mounting ORiNOCO® 802.11n Access Points - Hardware Installation Guide 19 Hardware Overview and Installation Ceiling Mounting: 1. Place the mounting plate on the T-bar ceiling such that the embossed letter ‘L’ is at the top-center position and the vent-holes are facing your left hand side. 2. Fasten the mounting plate by using a pair of plastic anchors and screws provided with the product package. 3. Hold the device with its rear panel facing the mounting plate, such that the vent-holes on the device and the vent-holes on the mounting plate rest on each other. 4. Align the two keyholes on the device with the two holders on the mounting plate. 5. Carefully, slide the device towards your right hand side, until the holders on the mounting plate fasten securely onto the keyholes of the device. Figure 2-9 Ceiling Mounting Mounting AP-8100 to AP-800/8000 mounting plate (Optional) In case, you are mounting AP-8100 to an already installed AP-800/8000 Mounting Plate (P/N 67439), then follow the following steps. Wall Mounting: 1. Hold the device such that the ‘Reload’ is towards your right hand side and the ‘LEDs’ towards left hand side. 2. Align the two keyholes on the device with the two holders on the mounting plate. 3. Carefully, slide down the device until the holders on the mounting plate fasten securely onto the keyholes of the device. Ceiling Mounting: 1. Hold the device such that the rear panel of the device is facing the mounting plate, with ‘Reload’ towards your right hand side and ‘LEDs’ towards left hand side. 2. Align the two keyholes on the device with the two holders on the mounting plate. 3. Carefully, slide the device backwards until the holders on the mounting plate fasten securely onto the keyholes of the device. : Ensure that the mounting plate is fixed in the similar fashion, as described in AP-800/AP-8000 mounting procedures (See Installation Procedure). 2.2.5.3 Step 3: Power On the Device To power on the device, plug in the power cord into a power outlet. There is no ON/OFF switch on the device. To disconnect power: • Unplug the power cable from the power socket of the device, if using power adapter. • Unplug the RJ45 connector from the Data & Power Out port on the DC injector, if using the Gigabit Ethernet PoE. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 20 Hardware Overview and Installation 2.2.5.4 Step 4: View LEDs When the device is powered on, it performs startup diagnostics. When startup is complete, the LEDs show the operational state of the device. Tabulated below is the behavior of the four LEDs on the device. LED Power LED Symbol Behavior Color Glows green when the device is switched ON. • Glows green when the device is connected to a 1 Gbps link. • Blinks green when the traffic is being transmitted or received on the 1 Gbps link. Ethernet LED • Glows amber when the device is connected to a 100 Mbps link. • Blinks amber when the traffic is being transmitted or received on the 100 Mbps link. • Glows red when the device is connected to a 10 Mbps link. • Blinks red when the traffic is being transmitted or received on the 10 Mbps link. 2.4 GHz LED • Glows green when the wireless interface 2 is in operational state. 5 GHz LED • Glows green when the wireless interface 1 is in operational state. • Blinks green when wireless traffic is being transmitted or received. • Blinks green when wireless traffic is being transmitted or received. : When the Reload button is pressed, the Power LED glows amber. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 21 3 Hardware Specifications This chapter covers the hardware specifications of the following products: • ORiNOCO® AP-800 and AP-8000 • ORiNOCO® AP-8100 3.1 ORiNOCO® AP-800 and AP-8000 Category Specification Radio Module Single Radio Access Point (AP-800) / Dual Radio Access Point (AP-8000) 3x3 MIMO per radio Wireless Protocol 802.11a/n 802.11a 802.11g/n 802.11g Frequency 5.150 - 5.850 GHz* 2.4 - 2.483 GHz* * Subject to Individual Country Regulations Channel bandwidth 20MHz and 40MHz for 802.11n 20MHz for 802.11a/b/g Modulation • MCS0 - MCS15 for 802.11n (6.5 Mbps -300 Mbps) • BPSK, QPSK, 16-QAM and 64-QAM for 802.11a and 802.11g (6 Mbps - 54 Mbps) • DSSS for 802.11b (1 Mbps -11 Mbps) Device Interface Ethernet: Auto-sensing 10/100/1000BASE-T Ethernet Antenna Connector: 3 RP-SMA connectors for AP-800 6 RP-SMA connectors for AP-8000 LED Indicators Refer Step 5: View LEDs Antennas 3 Single-Band (AP-800) / 6 Dual-Band (AP-8000) Omni-Antennas and reverse SMA connector with 3 dBi gain. Network Architecture Type Infrastructure Transmit Power Operational Modes Transmit Power* (dBm) 20 MHz 40 MHz 802.11b 19 802.11a/g 17 802.11na/ng 16 14 * Combined Tx Power values ORiNOCO® 802.11n Access Points - Hardware Installation Guide 22 Hardware Specifications Receive Sensitivity 11b 11a/g 11n Data Rate (Mbps) Receive Sensitivity (2.4-5Ghz) Data Rate (Mbps) Receive Sensitivity (2.4-5Ghz) Data Rate (MCS*) Receive Sensitivity (2.4-5Ghz) -94 -96 MCS 0 -90 11 -91 36 -87 MCS 8 -91 48 -83 MCS 10 -83 54 -82 MCS 15 -72 *MCS refers to Modulation Coding Scheme. Local Configuration Support RS-232 Serial port, DB9 Female Remote Configuration Support Telnet and SSH, Web GUI (http) and SSL (https), TFTP SNMP v1, v2c and v3 SNMP trap and Syslog PVES (ProximVision ES Network Management Systems) Message Authentication 802.11i AES message authentication with 128 bit keys TKIP with 128 bit Michael Message Integrity Check Intrusion detection Detect MIC intrusion attacks Certifications Wi-Fi Certification - Enterprise 802.11 a/b/g/n Dimensions (L x W x H) 11.1 x 6.85 x 1.89 in. (282 x 174 x 48 mm) : These dimensions exclude the antennas. Weight AP-800 - 0.7 Kgs (1.54 lbs) AP-8000 - 0.75 Kgs (1.65 lbs) Environmental Operating Temperatures: 0 to 55ºC 5 to 95 percent (non-condensing) Storage Temperature: -20º to 75ºC MTBF 43,800 hrs Warranty One year parts/labor ORiNOCO® 802.11n Access Points - Hardware Installation Guide 23 Hardware Specifications 3.2 ORiNOCO® AP-8100 Category Specification Power Requirements Power Adapter: 12V/1.25A Power over Ethernet (PoE) (optional): 48V / Any 802.3af compliant Gigabit PoE Radio Module Dual Radio Access Point, 2x2 MIMO per radio Radio1: IEEE 802.11a/n Radio2: IEEE 802.11b/g/n Wireless Protocol 802.11a/n 802.11a 802.11g/n 802.11g Frequency 5.150 - 5.850 GHz* 2.4 - 2.483 GHz * Subject to Individual Country Regulations Channel bandwidth 20MHz and 40MHz for 802.11n 20MHz for 802.11a/b/g Modulation • BPSK, QPSK, 16-QAM and 64-QAM: – With data rates of 6.5 Mbps -300 Mbps for 802.11n – With data rates of 6 Mbps - 54 Mbps for 802.11a and 802.11g • DSSS, CCK: With data rates of 1 Mbps -11 Mbps for 802.11b Device Interface Ethernet: Auto-sensing 10/100/1000BASE-T Ethernet LED Indicators Refer Step 4: View LEDs Antennas 4 Modular High Efficiency built-in PIFA Antennas with a peak gain of: – 3dBi for 2.4 GHz frequency. – 4dBi for 5 GHz frequency. Network Architecture Type Infrastructure Transmit Power 11b 11a/g 11n Data Rates (Mbps) Transmission Power* Data Rates (Mbps) Transmission Power* Data Rate (MCS*) Transmission Power* 1 to 11 20 6 to 48 20 MCS 0 to 5 20 MCS 6 19 MCS 7 17 54 20 * Combined Tx Power values * MCS refers to Modulation Coding Scheme. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 24 Hardware Specifications Receive Sensitivity 11b 11a/g 11n Data Rate (Mbps) Receive Sensitivity (2.4-5Ghz) Data Rate (Mbps) Receive Sensitivity (2.4-5Ghz) Data Rate (MCS*) -93 -90 11 -90 54 -75 Receive Sensitivity (2.4/5Ghz) 20 MHz 40 MHz MCS 0 -87 -86 MCS 7 -70 -66 * MCS refers to Modulation Coding Scheme. Remote Configuration Support Telnet and SSH, Web GUI (http) and SSL (https), TFTP SNMP v1, v2c and v3 SNMP trap and Syslog Message Authentication 802.11i AES message authentication with 128 bit keys TKIP with 128 bit Michael Message Integrity Check Intrusion detection Detect MIC intrusion attacks Certifications Wi-Fi Certification - Enterprise 802.11 a/b/g/n Dimensions (L x W x H) 6.69 x 6.69 x 1.74 in. (170 x 170 x 44.1 mm) Weight 0.340 kg (0.75 lbs) Environmental Operating Temperatures: 0 to 45ºC 5 to 95 percent (non-condensing) Storage Temperature: - 40º to 70ºC MTBF >100,000 hrs Warranty One year parts/labor ORiNOCO® 802.11n Access Points - Hardware Installation Guide 25 A Glossary and Abbreviations Glossary Access point A wireless network transceiver or “base station” hub, often used to connect a local area network to one or more wireless devices. An access point (also called AP) can provide a communication link to a wired local area network also. Advanced Encryption Standard (AES) It is a symmetric-key encryption standard, containing three block ciphers AES-128, AES-192, AES-256. Each of these ciphers has a 128-bit block size, with key sizes of 128, 192 and 256 bits, respectively. Dual-Band Dual-band refers to a device's ability to function on two different frequency bands. HTTP/HTTPS Hypertext Transfer Protocol (HTTP) is the protocol to transport Web pages. When you access the Internet with your browser, the HTTP protocol is used for data transport (http://www.Tsunamiwireless.com). When you access the unit by using the Web Interface, HTTP is used to transport the information. HTTPS is the Secure Hypertext Transfer Protocol. Management Information Base (MIB) A Management Information Base (MIB) is a formal description of a set of network objects that can be managed with the Simple Network Management Protocol (SNMP). A MIB can be loaded by a management application so that it knows the unit specific objects. Orthogonal Frequency Division Multiplexing (OFDM) OFDM is a frequency-division multiplexing (FDM) scheme, a method of encoding digital data on multiple carrier frequencies. A large number of closely spaced orthogonal sub-carrier signals are used to carry data. The data is divided into several parallel data streams/channels, one for each sub-carrier, maintaining total data rates similar to conventional single-carrier modulation schemes in the same bandwidth. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 26 Glossary and Abbreviations ScanTool Proxim’s ScanTool is a software utility that runs on Microsoft Windows machine. By using ScanTool, you can • Scan devices (Proxim devices only) available on the network • Obtain device’s IP address • Modify device’s IP Configuration parameters (IP Address, Address Type, Gateway and so on) • Launch the Web interface • Switch between the network adapters, if there are multiple network adapters in the Personal Computer Simple Network Management Protocol (SNMP) A protocol used for the communication between a network management application and the devices it is managing. The network management application is called the SNMP manager and the devices it manages will have SNMP agents. Not only the unit but also almost every network device contains a SNMP agent. The manageable objects of a device are arranged in a Management Information Base, also called MIB. The Simple Network Management Protocol (SNMP) allows managers and agents to communicate for accessing these objects. Single-Band Single-band refers to a device's ability to function only on one frequency band. TCP / IP The TCP/IP internet-suite protocol describes a set of general design guidelines and implementations of specific networking protocols to enable computers to communicate over a network. TCP/IP provides end-to-end connectivity specifying how data should be formatted, addressed, transmitted, routed and received at the destination. Telnet Telnet is a network protocol used on the Internet or local area networks to access the command-line interface, on a remote host. Most network equipment and operating systems with a TCP/IP stack support a Telnet service for remote configuration. Trivial File Transfer Protocol (TFTP) Trivial File Transfer Protocol (TFTP) is a lightweight protocol for transferring files that is like a simple form of File Transfer Protocol (FTP). A TFTP client is implemented on the unit. By using the upload and download commands, the unit can copy a file to or from a TFTP server. VLAN The Virtual Local Area Network (VLAN) feature helps in logical grouping of network host on different physical LAN segments, which can communicate with each other as if they are all on the same physical LAN segment. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 27 Glossary and Abbreviations WPA Wi-Fi Protected Access is a Wi-Fi security standard that provides a high level of wireless network security. It uses data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys and ensures that the keys are not tampered with. User authentication is performed through the Extensible Authentication Protocol (EAP), to ensure that only authorized network users can access the network. Abbreviations AP Access Point AES Advanced Encryption Standard CLI Command Line Interface Gbps Gigabit Per Second GPL General Public License HTTP HyperText Transfer Protocol HTTPS HyperText Transfer Protocol Secure IEEE Institute of Electrical and Electronics Engineers IP Internet Protocol LAN Local Area Network LED Light Emitting Diode LGPL Lesser General Public License MAN Metropolitan Area Networks Mbps Megabits Per Second MIMO Multiple-input and multiple-output MCS Modulation Coding Scheme ORiNOCO® 802.11n Access Points - Hardware Installation Guide 28 Glossary and Abbreviations OFDM Orthogonal Frequency Division Multiplexing PoE Power Over Ethernet PIFA Planar Inverted ‘F’ Antenna SKU Stock Keeping Unit SNMP Simple Network Management Protocol SNTP Simple Network Time Protocol TCP Transmission Control Protocol TFTP Trivial File Transfer Protocol TKIP Temporal Key Integrity Protocol USM User Security Model WLAN Wireless Local Area Networks WPA Wi-Fi Protected Access ORiNOCO® 802.11n Access Points - Hardware Installation Guide 29 Statement of Warranty Warranty Coverage Proxim Wireless Corporation warrants that its products are manufactured solely from new parts, conform substantially to specifications, and will be free of defects in material and workmanship for a Warranty Period of 1 year from the date of purchase. Repair or Replacement When Proxim determines that a returned product does not meet the warranted criteria during the warranty period, Proxim at its option, will either: (a) repair the defective product; (b) replace the defective product with a new or refurbished product that is at least equivalent to the original; or (c) refund the price paid for the defective product. Generally, products are repaired or replaced within thirty (30) business days of receipt of the product at a Proxim Logistical/Repair Center. The warranty period for repaired or replacement products is ninety (90) days or the remainder of the original warranty period, whichever is longer. These three alternatives constitute the customer’s sole and exclusive remedy and Proxim’s sole and exclusive liability under warranty provisions. Limitations of Warranty Proxim’s warranties do not apply to any product (hardware or software) which has (a) been subjected to abuse, misuse, neglect, accident, or mishandling, (b) been opened, repaired, modified, or altered by anyone other than Proxim, (c) been used for or subjected to applications, environments, or physical or electrical stress or conditions other than as intended and recommended by Proxim, (d) been improperly stored, transported, installed, or used, or (e) had its serial number or other identification markings altered or removed. Buyers can contact Proxim Wireless Customer Service Center either by telephone or via web. Support and repair of products that are out of warranty will be subject to a fee. Contact information is shown below. Additional support information can be found at Proxim Wireless’s web site at http://support.proxim.com. Contact technical support via telephone as follows: USA and Canada Customers Phone: +1-408-383-7700; +1-866-674-6626 Business Hours: 24x7 live response. Tier 3 support: 8 a.m. to 5 p.m. M-F PDT (UTC/GMT -7 hrs) International Customers Phone: +1-408-383-7700; 0800-916475 (France); 8-800-100-9485 (Russia) Business Hours: 24x7 live response. Tier 3 support: 8 a.m. to 5 p.m. M-F PDT (UTC/GMT -7 hrs) General Procedures When contacting the Customer Service for support, Buyer should be prepared to provide the product description and serial number and a description of the problem. The serial number should be on the product. In the event the Customer Service Center determines that the problem can be corrected with a software update, Buyer might be instructed to download the update from Proxim Wireless’s web site or, if that’s not possible, the update will be sent to Buyer. In the event the Customer Service Center instructs Buyer to return the product to Proxim Wireless for repair or replacement, the Customer Service Center will provide Buyer a Return Material Authorization (“RMA”) number and shipping instructions. Buyer must return the defective product to Proxim Wireless, properly packaged to prevent damage, shipping prepaid, with the RMA number prominently displayed on the outside of the container. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 30 Statement of Warranty Calls to the Customer Service Center for reasons other than product failure will not be accepted unless Buyer has purchased a Proxim Wireless Service Contract or the call is made within the warranty period. After the warranty period, Technical Support is fee based (detailed in Technical Services and Support). If Proxim Wireless reasonably determines that a returned product is not defective or is not covered by the terms of this Warranty, Buyer shall be charged a service charge and return shipping charges. Other Information Search Knowledgebase Proxim Wireless stores all resolved problems in a solution database at the following URL: http://support.proxim.com. Ask a Question or Open an Issue Submit a question or open an issue to Proxim Wireless technical support staff at the following URL: http://support.proxim.com/cgi-bin/proxim.cfg/php/enduser/ask.php. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 31 Technical Services and Support Obtaining Technical Service and Support If you are having trouble using the Proxim product, please read this manual and the additional documentation provided with your product. If you require additional support to resolve your issue, please be ready to provide the following information before you contact Proxim’s Technical Services team: • Product information – Part number and serial number of the suspected faulty device • Trouble/error information – Trouble/symptom being experienced – Activities completed to confirm fault – Network information (What kind of network are you using?) – Circumstances that preceded or led up to the error – Message or alarms viewed – Steps taken to reproduce the problem • ServPak information (if a Servpak customer): – ServPak account number • Registration information – If the product is not registered, date and location where you purchased the product : Technical Support is free for the warranty period from the date of purchase. Support Options Proxim eService Web Site Support The Proxim eService Web site is available 7x24x365 at http://support.proxim.com. On the Proxim eService Web Site, you can access the following services: • Product Download Page: Provides quick links to product firmware, software, and documentation downloads. • Proxim TV Links: A link to helpful video tutorials. • Knowledgebase: A solution database of all the resolved problems. You can search by product, category, keywords, or phrases. • Live Chat: Chat with a support technician on-line or request to call back at a later time. • Open Ticket / Ask Question: Submit a question to our technical support staff who will reply to you by email. • My Account / Tickets: Login to check the status of your questions, modify your answer update notifications, update your personal profile, or access restricted information and features. • Provide Feedback: Submit a suggestion, complaint, or other feedback about the support site. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 32 Technical Services and Support Telephone Support Contact technical support via telephone as follows: USA and Canada Customers Phone: +1-408-383-7700; +1-866-674-6626 Business Hours: 24x7 live response. Tier 3 support: 8 a.m. to 5 p.m. M-F PDT (UTC/GMT -7 hrs) International Customers Phone: +1-408-383-7700; 0800-916475 (France); 8-800-100-9485 (Russia) Business Hours: 24x7 live response. Tier 3 support: 8 a.m. to 5 p.m. M-F PDT (UTC/GMT -7 hrs) ServPak Support To provide even greater investment protection, Proxim Wireless offers a cost-effective support program called ServPak. ServPak is a program of enhanced service support options that can be purchased as a bundle or individually, tailored to meet your specific needs. Whether your requirement is round the clock technical support or advance replacement service, we are confident that the level of support provided in every service in our portfolio will exceed your expectations. • Advanced Replacement of Hardware: Can you afford to be down in the event of a hardware failure? Our guaranteed turnaround time for return to factory repair is 30 days or less. Those customers who purchase this service are entitled to advance replacement of refurbished or new hardware guaranteed to be shipped out by the Next Business Day. Hardware is shipped Monday – Friday, 8:00 AM – 2:00 PM (PST). • Extended Warranty: Extend the life of your networking investment by adding 1, 2, or 3 years to your products standard warranty. This service coverage provides unlimited repair of your Proxim hardware for the life of the service contract. The cost of an extended warranty is far less than the cost of a repair providing a sensible return on your investment. • 7x24x365 Technical Support: This service provides unlimited, direct access to Proxim’s world-class Tier 3 technical support engineers 24 hours a day, 7 days a week, 365 days a year including Holidays. Customers who purchase this service can rest assured that their call for technical assistance will be answered and a case opened immediately to document the problem, troubleshoot, identify the solution and resolve the incident in a timely manner or refer to an escalation manager for closure. • 8x5 Technical Support: This service provides unlimited, direct access to Proxim's world-class technical support 8 hours a day, 5 days a week from 8:00AM - 5:00PM (PDT). Typically, technical support is provided for free for the entire time the product is covered by a Proxim warranty. Beyond this period, technical support is available at cost on a per incident basis. With the 8x5 Technical Support service, technical support will be available for the duration of the ServPak contract at no additional costs. • Software Maintenance: It's important to maintain and enhance security and performance of wireless equipment and Proxim makes this easy by providing a Software Maintenance program that enables customers to access new features and functionality, rich software upgrades and updates. Customers will also have full access to Proxim's vast knowledgebase of technical bulletins, white papers and troubleshooting documents. • Priority Queuing Phone Support: This service provides customers with a one hour response time for technical phone support. There is no waiting in line for those urgent calls for technical support. Packaged Services • 24 x 7 Enhanced ServPak – 24 x7 Technical Support – Software Maintenance – Advanced Hardware Replacement – Extends Warranty* – Knowledge Base Access ORiNOCO® 802.11n Access Points - Hardware Installation Guide 33 Technical Services and Support – Priority Queuing * if units are out of standard warranty • 8 x 5 Enhanced ServPak – 8 x 5 Technical Support – Software Maintenance – Advanced Hardware Replacement – Extends Warranty* – Knowledge Base Access – Priority Queuing * if units are out of standard warranty ServPak Standalone Services • Extended Warranty ServPak • Advance Hardware Replacement ServPak Proxim Warranty vs. ServPak Service Service Features ServPak Warranty Technical Support, Configurations, Troubleshooting Duration of Product Warranty. 8X5 Normal Business Hrs Priority Queuing Available Knowledge Base Access Available Available Software Upgrades Available Advance Replacement Service 8x5xNBD Expert Technical Support - Not a feature service option To purchase ServPak support services, please contact your authorized Proxim distributor. To receive more information or for questions on any of the available ServPak support options, please visit our website at http://www.proxim.com/support/servpak, call Proxim Support (For telephone numbers, see Telephone Support) or send an email to servpak@proxim.com. Technical Support Policy Technical Support for Current Products during Warranty Period All Customers are entitled to free technical support for the Proxim products they purchase from Proxim’s authorized resellers or distributors. Technical Support is defined as communication via the Proxim Support website (http://support.proxim.com) and/or via telephone. This technical support will be provided for free for the entire time the product is covered by a Proxim warranty. The term of Proxim’s warranty is determined according to the agreement under which the product was sold and generally varies from 3 months to 2 years depending on the product. If a Customer disagrees with Proxim’s determination of warranty duration, a request for review supported by a copy of all product purchase documentation may be submitted. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 34 Technical Services and Support Technical Support for Current Products after Warranty Period After the warranty period, technical support on products then being sold by Proxim will be based upon one of the following three options Customers can choose: • Customers can choose to purchase one of Proxim’s ServPak extended warranty and enhanced support packages for the product • Customers can choose to purchase one-time per-incident technical support for the product for a fee • Customers can choose to call the reseller or distributor who sold them the product for technical support Tech Support on Discontinued Products Technical Support on some products that Proxim has declared as EOL (End of Life) or otherwise is no longer selling is available based upon one of the following three options Customers can choose: • For some discontinued products, Customers can choose to purchase one of Proxim’s EOL ServPak support packages for the product – No EOL ServPak support package will be available for any product discontinued more than 5 years ago – No EOL ServPak support package is available for certain discontinued products • Customers can choose to purchase one-time per-incident technical support for the product on a per hour basis at a rate of $125 an hour (4 hours minimum payable in advance by major credit card). This fee is payable in addition to any RMA fee that may be charged to subsequently repair the product. • Customers can choose to call the reseller or distributor who sold them the product for technical support All Proxim technical support for discontinued products, whether through an EOL ServPak package or otherwise, is provided on a “best effort” basis and is subject to the continued availability of necessary components, equipment, and other technical resources. Note that Proxim is unable to support or warrant any equipment that has been modified, whether this modification is physical, or if third-party software codes have been loaded onto the product. ORiNOCO® 802.11n Access Points - Hardware Installation Guide 35
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Page Mode : UseOutlines XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Producer : Acrobat Distiller 8.0.0 (Windows) Creator Tool : FrameMaker 8.0 Modify Date : 2012:09:04 11:52:02+05:30 Create Date : 2012:08:16 10:56:04Z Metadata Date : 2012:09:04 11:52:02+05:30 Format : application/pdf Title : ORiNOCO_AccessPoints_HardwareInstGuide.book Creator : nsuri Document ID : uuid:360b417a-e76a-409f-b96c-26385e5a5829 Instance ID : uuid:8516985e-09e1-4f95-863c-5efc109416ed Page Count : 35 Author : nsuriEXIF Metadata provided by EXIF.tools