Psion 7545MBWP GSM/GPRS/UMTS/HSPA Module User Manual installation guide

Download:
Mirror Download [FCC.gov]
Document ID	1731129
Application ID	jsFh9dE/wzpRemlmGtK11Q==
Document Description	installation guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	41.33kB (516626 bits)
Date Submitted	2012-06-27 00:00:00
Date Available	2012-06-27 00:00:00
Creation Date	1993-01-07 14:41:50
Producing Software	Acrobat Distiller 10.1.3 (Windows)
Document Lastmod	2012-06-25 16:29:56
Document Title	Omnii End-cap with GPS & HSPA+ Radio Kit Installation
Document Creator	FrameMaker 9.0
Document Author:	Gabrielle Neff

OMNII™ END-CAP WITH GPS & HSPA+ RADIO KIT
INSTALLATION
Warning: The installation of any components must be performed using the appropriate anti-static devices. If unavailable, discharge static from your body by touching a grounded metallic object before opening any covers on
the hand-held.
This instruction sheet describes how to install the GPS/HSPA+ Radio Kit and an end-cap kit.
The GPS Radio Kit contains the following:
• GPS radio with frame
• Torx T6 screws (x 3)
• Regulatory label 1004434
The GPS End-cap Kit includes:
• GPS end-cap with antenna attached.
• Torx T10 screws (x 4)
The tools listed below are needed for this procedure:
• Torx T10 screwdriver
• Torx T6 screwdriver
• small needle-nose pliers
1. Getting the Omnii Ready for GPS/HSPA+ Installation
Warning: Always disconnect the Omnii from all power sources (battery & A/C power) before servicing components.
Figure 1
Torx T6 screws (x2)
Blanking plate
End-Cap
Torx T10 screws (x8)
Torx T10 End-cap screws (x4)
Tighten screws in sequence indicated.
•
•
•
•
•
•
Remove the battery.
Remove the blanking plate (four screws) using a Torx T10 screwdriver.
Using a Torx T6 screwdriver, remove the two top-most screws on the front of the unit, just above the display.
Remove the eight T10 screws holding the back cover to the main housing. The screws are illustrated in Figure 1.
Carefully separate the back cover from the chassis without putting strain on the cables that are still connected.
Locate the trigger/speaker cable at the top corner of unit. Grasp the wires in a bundle, and lift them straight
up to disconnect the harness from the socket on the main logic board. Carefully disconnect any other cables.
Warning: Do not try to pry the harness from the socket, or you may dislocate the socket from the main logic board.
•
Remove the existing end-cap (four screws) using a Torx T10 screwdriver.
2. Installing the GPS/HSPA+ Radio Module
•
•
Align the 100-pin connector on the GPS radio module with the connector on the main logic board, and press
down to attach it.
Using a Torx T6 screwdriver, secure the GPS radio to the main logic board with 3 screws (M2x5 mm), torqued to
2.5 in-lb (0.28 N-m).
© Copyright 2012 by Psion Inc.
Psion, the Psion logo, and the names of other products and services provided by Psion are trademarks of
Psion Inc. All trademarks used herein are the property of their respective owners.
June 25, 2012
8000274.B Sheet 1 of 1
Figure 2
100-pin connector
Torx T6 screws (x3)
GPS bypass cable
3. Attaching the GPS/HSPA+ End-Cap
•
•
Run the cables (x3) and scanner/imager flex cable through the opening at the top of the expansion back cover.
Using a Torx T10 screwdriver and the four screws provided (M3 x 6 mm), secure the GPS end-cap to the expansion
back cover. Torque to 5 in-lb (0.56 N-m).
4. Reassembling Omnii
•
Before reattaching the back cover, connect the pistol grip trigger/speaker wire harness to socket J11 on the main
logic board. Connect the camera flex cable to socket J9 on the main logic board.
• If a scanner/imager flex cable is present in the end-cap, connect it to socket J13 on the main logic board as shown in
Figure 3. If no cable has previously been installed in this socket, there may be a piece of “dummy” stiffener that must
be removed before inserting the cable.
• Make certain the GPS bypass cable is connected (see Figure 2 on the previous page).
Figure 3
Flip latch open
Insert cable
Flip latch closed
J13
J9
J11
•
•
•
•
•
•
•
Fit the back cover in place against the main housing, ensuring that no cables are caught in the seal.
Using a Torx T10 screwdriver, tighten the eight screws (M3x6 mm) to a torque of 5 in-lb (0.56 N-m). Install the screws
in the sequence shown in Figure 1 on the previous page to ensure a consistent seal around the opening.
Using a Torx T6 screwdriver, replace the two screws (M2x8 mm) above the display on the front of the unit. Torque to
2.5 in-lb (0.28 N-m).
Through the scanner pod opening, use small needle-nose pliers to route the grey GPS antenna cable under the two
metal cable restraints on the left side of the GPS module.
Press the grey GPS antenna connector into the socket labelled GRY on the left side of the unit. Snap it into place.
Through the scanner pod opening, use small needle-nose pliers to route the black HSPA+ radio antenna cable under
the metal cable restraint at the top of the radio module.
Press the black HSPA+ antenna connector into the socket labelled BLK on the radio module. Snap it into place.
Affix regulatory label here
GPS antenna
connector
Diversity antenna
connector
•
•
•
•
Metal cable restraint
HSPA+ antenna
connector
Press the green diversity cable connector into the socket labelled GRN.
Affix regulatory label 1004434.
Reattach the blanking plate using a Torx T10 screwdriver and four screws (M3x5 mm) to 5 in-lb (0.56 N-m).
Install the battery.
COMPANY HEADQUARTERS
Psion Inc.
2100 Meadowvale Boulevard, Mississauga
Ontario, Canada L5N 7J9
Tel:
+1 905 813 9900
Fax:
+1 905 812 6300
SUPPORT SERVICES
For local support services, go to:
http://www.psion.com/service-and-support.htm

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : Gabrielle Neff
Copyright                       : 2012 Psion Inc.
Create Date                     : 1993:01:07 14:41:50Z
Keywords                        : Instruction, Sheet, 8000274, RevB
Modify Date                     : 2012:06:25 16:29:56-04:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Producer                        : Acrobat Distiller 10.1.3 (Windows)
Format                          : application/pdf
Title                           : Omnii End-cap with GPS & HSPA+ Radio Kit Installation
Creator                         : Gabrielle Neff
Creator Tool                    : FrameMaker 9.0
Metadata Date                   : 2012:06:25 16:29:56-04:00
Document ID                     : uuid:c3bfea9a-542c-448a-9cc8-08f6cca4c6be
Instance ID                     : uuid:7b63c5a8-974c-41fb-af28-d821708fe156
Page Mode                       : UseOutlines
Page Count                      : 2

EXIF Metadata provided by EXIF.tools