Samsung Electronics Co CK32PS 32-inch Color Monitor User Manual 1

Download:
Mirror Download [FCC.gov]
Document ID	360788
Application ID	04JtYVAphUpBFr4Q/QHFlA==
Document Description	Users Manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	241.32kB (3016478 bits)
Date Submitted	2003-09-29 00:00:00
Date Available	2003-09-29 00:00:00
Creation Date	2003-09-29 16:02:18
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2003-09-29 16:02:39
Document Title	Users Manual 1

SyncMaster 323T,403T
INDEX
Main Page
Adjusting Your LCD Monitor
User control buttons
Safety Instructions
Notational
Power
Installation
Cleaning
Other
Introduction
OSD Functions
Troubleshooting
Check before Calling for Service
Problems and Solutions
Q&A
Specifications
Unpacking
General Specifications
Front
PowerSaver
Rear
Preset Timing Modes
Remote Control
Mechanical Lay-out
Setup
Installing Stand Kit
Connecting Your Monitor
Multiple Display Control (MDC)
Information
Service Center
Terms
Regulatory
Natural Color
For Better Display
Authority
Notational
Failure to follow directions noted by this symbol could result in bodily harm or damage to
equipment.
Prohibited
Important to read and understand at all times
Do not disassemble
Disconnect the plug from the outlet
Do not touch
Grounding to prevent an electric shock
Power
When not used for extended periods of time, set your PC to DPMS. If using a
screen saver, set it to the active screen mode.
Do not use a damaged or loose plug.
z This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands.
z This may cause an electric shock or fire.
Use only a properly grounded plug and receptacle.
z An improper ground may cause electric shock or equipment damage.
Do not excessively bend the plug and wire nor place heavy objects
upon them, which could cause damage.
z This may cause an electric shock or fire.
Disconnect the plug from the outlet during storms or lightening or if it
is not used for a long period of time.
z Failure to do so may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet.
z This may cause a fire.
Installation
Do not cover the vents on the monitor cabinet.
z Bad ventilation may cause a breakdown or fire.
Put your monitor in a location with low humidity and a minimum of dust.
z An electric shock or fire could result inside the monitor.
Do not drop the monitor when moving it.
z This may cause damage to the product or human body.
Place the monitor on a flat and stable surface.
z The monitor can cause injury by falling.
Set down the monitor carefully.
z It could be damaged or broken.
Do not place the monitor face down.
z The TFT-LCD surface may be damaged.
Cleaning
When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly
moistened, soft fabric.
Do not spray detergent directly on the monitor.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it
properly with a dry cloth.
z A dirty connector can cause an electric shock or fire.
Do not set a glass of water, chemicals or any small metal objects on the
monitor.
z This may cause damage, electric shock or a fire.
z If a foreign substance gets into the monitor, disconnect the plug and then
contact a service center.
Other
Do not remove cover(or back). No user serviceable parts inside.
z This may cause an electric shock or a fire.
z Refer servicing to qualified service personnel.
If your monitor does not operate normally - in particular, if there are any
unusual sounds or smells coming from it - unplug it immediately and
contact an authorized dealer or service.
z This may cause an electric shock or fire.
Do not place any heavy objects on the monitor.
z This may cause an electric shock or a fire.
For each hour of looking at the monitor, you should let your eyes rest for
5 minutes.
z This will reduce eye fatigue.
Do not use or store inflammable substances near the monitor.
z This may cause an explosion or fire.
Do not try to move the monitor by pulling on the wire or the signal cable.
z This may cause a breakdown, electric shock or a fire due to damage to
the cable.
Do not move the monitor right or left by pulling only the wire or the signal
cable.
z This may cause a breakdown, electric shock or a fire due to damage to
the cable.
Never insert anything metallic into the monitor openings.
z This may cause an electric shock, fire or injury.
If you view a fixed screen for an extended period of time, residual
image or blurriness may appear.
Change the mode to energy save or set a screensaver to moving
picture when you need to be away from the monitor for an extended
period of time.
Unpacking
Please make sure the following items are included with your monitor. If any items are missing, contact
your dealer.
Power Cord
Remote Control /
Batteries (AAA X 2)
User's Guide CD
Signal Cable
(15 pin D-Sub)
Cover-hole
Monitor
Warranty Card
(Not available in all locations)
RS232C CABLE
Temporary Stand
Sold separately
Wall Mount KIT
Speaker Set
PIVOT Installation CD
Contact a local Samsung Electronics service center to buy optional items.
Stand Kit
Front
For detailed information concerning the monitor functions, refer to User Controls under Adjusting Your
Monitor. The monitor's front configuration may vary slightly depending on the monitor model.
1. Auto button
6. Menu button
2. Source button
7. Power button
3. Exit button
8. Power indicator
4. Navigate button (Up-Down Button)
9. Remote Control Sensor
5. Adjust button (Left-Right Button)
/ Volume button
SyncMaster 403T
Rear
For detailed information concerning cable connections, refer to Connecting Cables under Setup.
The monitor's rear configuration may vary slightly depending on the monitor model.
1.
Power On/Off Switch
2.
Power port
3.
EXTERNAL CONTROL (RS232C Serial PORT) : MDC(Multiple Device Control) Program Port
4.
PC Video Connection Terminal
: Using D-Sub Cable (15 pin D-Sub) - RGB 1 mode (Analog PC)
5.
PC Video Connection Terminal
: Using DVI Cable (DVI-D to DVI-D) - RGB 2 mode (Digital PC)
Rear
6.
PC Video Connection Terminal / Component Connection Terminal : BNC cable (Input)
- RGB 3 (Analog PC) Connection : connecting B, G, R, H, V port
- Component Connection : connecting Pb, Y, Pr port
7.
PC Video Loopout Connection Terminal (RGB 3 (Analog PC)) /
Component Loopout Connection Terminal (Component) - BNC cable(Output)
8.
CVBS Video Connection Terminal : Video 1 mode (Input)
9.
CVBS Video Loopout Connection Terminal (Output)
10. S-Video Connection Terminal : Video 2 mode (Input)
11. S-Video Loopout Connection Terminal (Output)
12. Component Audio Connection Terminal (Input)
: When the input signal is connected to Terminal 6, the audio must be connect to this terminal only.
13. CVBS, S-Video Audio Connection Terminal (Input)
: When the input signal is connected to Terminal 8 or 10, the audio must be connect to this terminal
only.
Loopout Connection : Up to 5 monitors supported.
14. Speaker Out
15. PC Stereo Connection Terminal (Input)
16. Audio Line-out Connection Terminal (Output)
17. Kensington Lock
SyncMaster 323T
Rear
For detailed information concerning cable connections, refer to Connecting Cables under Setup.
The monitor's rear configuration may vary slightly depending on the monitor model.
1.
Power On/Off Switch
2.
Power port
3.
EXTERNAL CONTROL (RS232C Serial PORT) : MDC(Multiple Device Control) Program Port
4.
PC Video Connection Terminal
: Using D-Sub Cable (15 pin D-Sub) - RGB 1 mode (Analog PC)
5.
PC Video Connection Terminal
: Using DVI Cable (DVI-D to DVI-D) - RGB 2 mode (Digital PC)
Rear
6.
PC Video Connection Terminal / Component Connection Terminal : BNC cable (Input)
- RGB 3 (Analog PC) Connection : connecting B, G, R, H, V port
- Component Connection : connecting Pb, Y, Pr port
7.
PC Video Loopout Connection Terminal (RGB 3 (Analog PC)) /
Component Loopout Connection Terminal (Component) - BNC cable(Output)
8.
CVBS Video Connection Terminal : Video 1 mode (Input)
9.
CVBS Video Loopout Connection Terminal (Output)
10. S-Video Connection Terminal : Video 2 mode (Input)
11. S-Video Loopout Connection Terminal (Output)
12. Component Audio Connection Terminal (Input)
: When the input signal is connected to Terminal 6, the audio must be connect to this terminal only.
13. CVBS, S-Video Audio Connection Terminal (Input)
: When the input signal is connected to Terminal 8 or 10, the audio must be connect to this terminal
only.
Loopout Connection : Up to 5 monitors supported.
14.
Speaker Out
15.
PC Stereo Connection Terminal (Input)
16.
Audio Line-out Connection Terminal (Output)
17. Kensington Lock
Remote Control
For detailed information of the Remote Control Unit functions, refer to Adjusting Your Monitor > User
Controls > User Control Buttons > Remote Control buttons.
The remote control's configuration may vary slightly depending on the monitor model.
The Remote control may function within a range of 0.23 to 33 feet (7cm to 10m) and 30 degrees to the
left and right of the monitor's Remote Control Reception sensor.
Button Names | Replacing Batteries | Usage
1. Button Names
1. Power button
2. Auto button
3. Mute button
4. VOL(Volume)and Up/Down buttons
5. Source button
6. Number buttons
7. PIP button
8. PIP Size button
9. P.Size button
10. Still button
11. Display button
12. Sleep button
13. Menu button
14. Exit button
15. Swap button
16. Location button
2. Replacing Batteries
1. Slide out the cover pressing part marked
2. Insert the batteries matching their polarities (+, -).
3. Slide in the cover.
Mechanical Lay-out
1. Mechanical Lay-out
2. Monitor Head
SyncMaster 403T
Mechanical Lay-out
3. Stand
4. Speaker
Mechanical Lay-out
5. Mounting Bracket
Mechanical Lay-out
1. Mechanical Lay-out
2. Monitor Head
SyncMaster 323T
Mechanical Lay-out
3. Stand
4. Speaker
Mechanical Lay-out
5. Mounting Bracket

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2003:09:29 16:02:39-03:00
Create Date                     : 2003:09:29 16:02:18-03:00
Producer                        : Acrobat Distiller 5.0 (Windows)
Page Count                      : 20
Mod Date                        : 2003:09:29 16:02:39-03:00
Creation Date                   : 2003:09:29 16:02:18-03:00
Metadata Date                   : 2003:09:29 16:02:39-03:00
Has XFA                         : No

EXIF Metadata provided by EXIF.tools