Sirius XM Radio SX1E Sirius XM RX and FM TX User Manual XMH User Guide with Kit Part 1

Download:
Mirror Download [FCC.gov]
Document ID	1515474
Application ID	enRcjLUoSGAvTNAkaK8CJw==
Document Description	XMH User Guide with Kit Part 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	373.92kB (4673943 bits)
Date Submitted	2011-08-02 00:00:00
Date Available	2011-09-16 00:00:00
Creation Date	0000-00-00 00:00:00
Document Lastmod	0000-00-00 00:00:00
Document Title	XMH User Guide with Kit Part 1
Document Creator	Hewlett Packard MFP

Dock & Play Haifa»?!-
User Guide
Smashmg Pumpkin;
h w .
(((5iriqs_)gm)))
If you experience problems with the operation
or performance of your SiriusXM product,
DO NOT RETURN THIS PRODUCT TO YOUR RETAILER.
Call SiriusXM Listener Care at1-866-746-7961
and speak to one of our service representatives.
(«Siriusxnl‘»)
lAvnuvt "me
Table of Contents
.5
introduction
Fealures
Salety and Care lnlcrmation.
what‘s in the Box?
XMH Button Functions
PowerCennecI Vehicle Dock .
.ll
Vehicle Installalloll ........... . t 13
Stem: choose a Location fer vour
Radio .|4
step 2. install tne Dash or Vent Mount. |6
steo 3: Mount the Magnetic Mount
Antenna ..... 20
step 4: Route the Magnetic Mount
Antenna Cable
step 5: connect the Magnetic Mount
Antenna and Pawerconnecl Power
Adapter“ 37
step 5: Connect the Audio. 33
Subscrlbe ..... t ....... r ...... 47
Si
52
53
55
59
Using Your XMH
The Main Display.
Navigation Basics
Listening to satellite Rania,
FM Presets ........
special Features ....... . ....... 6|
Pause & Replay .,
Parental Cantrols
Where Else can You Use Your
XMH? ..... . , ...... . . ...... 59
Configuring Your XMH ..... .....7l
Radio ID . V .
channel Tuning .
Fina Available FM cnannels in
trour Area ..
Set and select an m Channe
Jump Settings
Se! Brightness
Set Audio Level.
Signal indicator.
Factory Settinos .
Demo Moue ..
Auto Shut oft.
Using tne Vehicle Dark From the
Universal xoress car Kit ........... Ba
Turn FM Transmitter Onloll .......... B9
Troubleshooting. . . ..... . . . . 91
Producl Specilicatlons .......... 97
Patent lnlormahon t 99
Envimnmental lnlurmat‘ion . . 99
sirlusXM 90- Day Limited
Warrantv ..... . . ........ 103
Introduction
Features
Thank you for purchasing the XM XMH with Vehlcle Kit!
XM XMH has these exciting features to enhance your overall experlence:
' Hear SiriusXM through your existing vehicle radio with easy, do-it'yourself
installation.
~ Large vibrant color display to View artist name, sonq title, and all channel
information with color backgrounds, channel graphics, and channel iconsa
' Pause. rewind and replay live Satellite Radio.
~ Browse other channels while listening to the current one.
- View artist name. song title, and channel information on the large color
displayr
' Store your favorite Channels for one touch access,
- Easily lock and unlock channels wlth mature content.
- One-Touch Jump'“ to trailic and weather for the city or your choice from a
list or 22 ol the most congested cities. or m the previous channel to which
you were listening
' Listen in multiple vehicles, at home, in the office or outdoors ' all with iust
one subscription.
- Vehicle Kit lncluded — add accessories ior your name, ollice, or other
vehicles
Please read through this User Guide before uslno your XMH!
Safety and Care Information
IMPDITANYI Self installation ’ slruclinns and lips are provided for your
. convenience. it is your responsi lily to determine it you have tne knowledoe.
skills. and pnysical aoluty required to properly perlorm an installation. SlrlusXM
shall nave no llapllity for damage or inlury resulting lrorn the Installation or use
of any SirlusXM or trurd parly prooucls. it is your responsibility to ensure tnat all
products are installed in adnerence with local laws and reoulatlons and in sucn a
manner as to allow a vehicle to toe operated selely and witnout distraction.
Sirlust product warranties do not cover the installation. removal or
reinstallatlon of any product,
‘ Do not expose tO extreme temperatures (above MO'F ar belaw “A'F, or
above EO'C or below ‘20'C).
- Do not expnse to muistures Do not use device near or in water. Do not touch
the device with wet hands.
- Do not let any loreiqn matter spill into device.
- Do not store in dusty areas.
- Do not Expose to chemicals such as benxene and thinners. Du not use liquid
or aerosol cleaners. Clean with a so“ damp cloth only.
- Do not expose to direct sunlight for a prolonged period pl time. and do not
expose to fire, flame, or other heat sources.
- Do not try to disassemble and/or repair device vourselfi
~ Do not drop your device or suhiect it to severe impact.
- Do not place heavy objects on device.
- Do not subiect device to excessive pressure.
- If the LCD screen is damaged, do not touch the liquid crystal fluid,
Introduction
Warning!
- Opening the case may result in electric shockt
- if the liquid crystal lluid comes in contact with your skin, wipe the skin area
with a cloth and then wash the skin thoroughly with soap and running water.
If the liquid crystal fluid comes into contact with your eyes, flush the eyes
with clean water for at least is minutes and seek medical care. it the liquid
crystal fluid is Ingested, flush your mouth thoroughly with water. Drink large
quantities ol water. and induce vomiting. Seek medical care.
- Make sure that you insert the PowerConnect" Power Adapter all the way
into the vehicle’s cigarette lighter or power adapter socket.
- ll you are using PowerConnect as your audio connection option, it is
advisable not to insert a multi-outlet adapter into the same vehicle cigarette
lighter or power adapter socket to simultaneously power other devices,
Some multi-outlel adapters can prevent the PowerConnect feature irom
working properly.
~ When using this product. it is always important to keep your eyes on the road
and hands on the steering wheel. Not doing so could result in personal Injury.
death. and/or damage to your device. accessories. and/or to your vehicle or
other property,
- vehicle installation, service activation. and Radio configuration functions should
not be performed while driving. Park your vehicle in a safe location before
beginning installation.
- This product contalns chemicals known to the state of California to cause
cancer and birth delects or other reproductive harm.
Vour device should be placed In your vehicle where it wIII not interlere with the
lunction oi safety features, e.q., deployment oi airbags. Failure to correctly place
device may result in injury to you or others, it the unit becomes detached during an
accident and/or obstructs the deployment or an airbag.
what's In the Box?
mm
OQQGG
O 0 G) (9 ®
..I.. ..|- (
XMH Radio
Aux In Cable
a vent Mount
| and Extended
5°” a vent Clamps
Routing Anapler
aw
Powerconnect Power Magnetic Mount
Adapler Antenna
Antenna 5. Dash Mnunt
Alcohol Preparation Pads
Introduction
XMH Button Functlons
Power Button Menu eutton m Button
Press to turn Radio Press to access advanced Press to access and cycle
on and oil. leatures and configuration throueh m presets.
options n configuration
options, press and hold Numb" Bum“
to return to main display Press mum w
5m"- a stored favorite
channel. press and
hold to store a
laverite channel;
also enter a channel
number.
Dir-ct Button
Press first before
entering the channel
numper, to directly
tune to a channel.
select Button
Press to confirm
selection ol highlighted
items in a menu or list,
Left and Riunt Buttons
Press to search lar
channels tiy categorv.
Pause and Replay Buttons Jump Button Retery Ktmb
Pause. rewlnd, and replay Press to oirectly access Rotate to preview and tune
up to so minutes cl live traffic and weather tor the to channels through the
radlo. city at your choice; or press channel llneup: also scrall
it ta oo halt to the previous through lists and highllaht
channel to which you were menu options.
llsteninq.
PowerConnect Vehicle Dock
Color-Coded Connectlnns
The color-coded PowerCOnned Vehicle Dock makes it simple to connect. Jusl
match the colors on the cable ends to the colors on the dock h: see What goes
where.
Rear Viaw
AUDIO (Green! ANT (Silyer) PWR (Ran) m lame)
connecnun mr Aux In Connecuon do! Connecllon lor Cannutiun (or
cable or apuonal the Magnem FewerConnut optional FM Direct
Cassette Adapter Maunt Antenna, Power Adamer. Adapter (sold
(sold separately), separately).
Introduction
WIre Gulde
The Powerconnect Vehicle Dock has a wire guide at the top rear that can help
you to organize lhe cables and wires connected to the dock. ll you need to brim;
a cable or wire from one side ol the flock to me other, uiilize the wire guide by
looping the cable though the wire guide as shown.
Wire Guide
Swan—m 5.32550:
Vehicle Installation
wmumel Do NOT attempt to install XMH while drivlnm Park your vehicle in a
sale Iocatlon betore beginning installation,
Step 1: Choose a Location for Your Radio
when installing XMH in your vehicle, choose a location where it will not block
your vision, interfere with the controls, or obstruct the air bag. The location
should be easily accessible and provide good visibility Bl the display, and should
not be located where it will be in direct sunlight, which will allect the Visibllitv at
the display screen.
Several examples ol XMH mounted in a vehicle are shown: A is the on dash
method using the Dash Mount. and B is the vent clip method using the Vent
Mount
Option] Option 2
“one“ 3
pd
Option 4 own" 5
Vehicle Installation
Step 2: Install the Dash or Vent Mount
Depending on your situation, you can either choose to use the Dash Mount or
the Vent Mounts
IMPORTANT! When you install the chosen mount, do not attach the flock to the
mount. All cables should be attached to the dock pnur to connecting the dock tn
the mount.
Installing the Dash Mount:
cAu'IlONl The adheswe used on the Dash Mount may he
. dilllcult to remave. no not install this mount un leather surleces
(Contact your vehicle dealer ll you are unsure almut your flash
surlace), and make sure the an temperature is at least so'r
llS'Cl during installation. If it's not al least so'r, turn on the
heater in your vehicle to bum; the temperature up to WT.
1 Locate a flat surface for the Dash Mount. Make sure there is ample room
let the Paws/Connect Vehicle Dock and XMH Radia when installedu
2 Set the orientation oi the Dash Mount before adhering it, Loosen the
knot: and adjust the adhesive (not for the location you selected in "Step 1:
Choose a Location for Your Radio" on page 14:
‘ Option 1 Sr Ootlon 3
shuuld be oriented
as I.
' Outlan 2 should be
oriented as II,
3 The dock mounting plate can be tilted in dillerent oirectlons. Adjust as
necessary lor your particular vehicle. When the orientation is correct,
tighten the knob.
Knob Ad/heslva Foul Duck Muuw
4 Clean the surface with the alcohol
preparation pad and let it dry
thoroughly.
5 Feel ofi the adhesive liner. Position.
press. and hold the Dash Mount in
place for 30 secends.
luronnm! Allow the Dash Mount adhesive to cure (dry) tor a minimum at 2-4
hours betore usmq the mount. The best adhesion occurs alter 24 hours.
TIP] To remove, carefully the adhesive pad with your finqers or a spoon.
warming the pad with a hair dryer for several minutes will help soften the
adhesive,
Vehicle Installation
Installinq the Vent Mount:
Enema-1 Vent Clumsy:
1 Locate a vent with hurilontal
louvers sturdy enouuh to hold your
PowerClsnnect Vehicle Dock and Radiot
z ll the vent luuvers in your ventele are
recessed, you may need to use the
longer vent clamps with the Vent Mount.
ll 50, remove the snerter vent clamps
and install the longer ones into the Vent
Mount Be sure to observe the orientation at the vent clamps as strewn
3 Push the Vent Mount onto the vehlde vent as shown (1) until it hooks on
the rear 07 the vent louver (2L
Remove End Cap Sllde Short Vent Clamps Out
sllde Extended Vent clamps In Replace End Cap
/<-
4 Rest the loot against the bottom 0' the Vent (2), arm adiust the tilt of the
Vent Mount hv repositioning the foot to a diflerent adjustment hole (3).
muss
To remove the Vent Mount, push the mount into the vent. Then lift up until
disengaged from the rear of the vent iouver, and remove the Vent Mount.
Vehicle Installation
Step 3: Mount the Maqnetlc Mount Antenna
Mount the Magnetic Muunt Antenna an the outside ol your vehicle. on a
hnrizontal surface that wlll always face the sky. The antenna contains a strong
magnet which will stick to any metal part of your vehicle. but wIII not damage the
vehicle
To Install the Magnetic Mount Antenna:
1 Choose the best location for your antenna considering
your vehicle type. Pav particular attention to any
accessories that you may have like luggage racks and
how frequently you may use them. Magnet
sedan/Coupe: We recommend mounting the antenna just above elther
the front Windshield or the back window as shown.
SUV: We recommend mounting the antenna at the rear of "19 ruof as
Shown.
Convertible: We recommend mounting the antenna 5! the leading edge
of the trunk as shown.
Pickup Truck: we recommend
mounting the antenna lust above the
front windshield as shown.
luvulfl'nnl Consult a prnlessional' stellar ll
vour vehlcle real or hnud is nnn~melallic [i.e.,
liberqlassl, or yau have difficulty finding a
location lor your anlenna.
2 Clean the surlace ol the selected mounting
locallon using (he alcohol preparation pad
and let it dry thoroughly.
Vehicle Installation
3 If you are |nsta|nng the antenna at the root edge. or hood edge, Instan the
Cable Routing Adapter to direct the antenna cable downward.
without Cable witn Came
Routing Adapter § _ Routing Adapter
tnstauea \ \ Installed
came Routing
Adapter onentation @
Place the antenna wire Sllde the cabte Routmq
into the groove of the Adapter down the antenna wire
Cable Rautunu Adapter and press it into the antenna
unlvl ut is flush with the bottom
otthe antenna
4 Place the antenna l" the location you Selected. Follow the Tips and
Cautlons shown on the next several naqes.
1m Mount the antenna on me
. roof (tar mast vehicles; or trunk
ller convertibles) where it has a
clear View of the skv m all
dnrectians.
Vehicle Installation
cnunoui Don't mount the antenna inside
the vehicle. for example, on the dashboard,
ol the vehicle's lmnt, back or side pillars.
cAufloN! unn'l mount the antenna on any J
@.
cAunoNi Don't mount the antenna close
to a (001 rack. Adjust the rack so it‘s further
away mm the antenna or move the antenna
closer to the center at the moi.
CAUTION] Don't mount the antenna
dose to another antenna. Mount n at
least 3 inches away.
Vehicle Installation
Step 4: Route the Magnetic Mount Antenna Cable
Belore you begin routing the antenna cable, read mesa uenerai instructions
idr how to route and hide the antenna cable. Then rauie your antenna cable
according in the instructions which follaw lor your specific type of vehicia
Use a blunt plastlc pugtv knife, 3 credit card,
a plastic knife, or a Similar blunt tool to lift the
rubber window mduidinq
/f/\§ Tuck the cable under the
4 l
, i
moulding around the Window
Feed cable under
rubber mouidinq
around window
Ruute cable out lrom under rear windshield
moulding and tuck into weafllerstrlnping
around trunk opening m
Avoid sharp bends by running cable through _
Weatherstripping Iar several inches Pull weatherstripplnq
from trunk opening
Tuck eahle into weatherslrlpplnq,
Route cable through Weatherstripping
several inches to avoid sharp bends
Pull cable nut 01 Weatherstripning
and route through trunk to cabin
Route cable out 0! window
moulding and into weather
strippina arnund trunk apenlnq
Vehicle Installation
Bring cable out of Weatherstripping and into trunk
Route cable along trunk
wall and into cabin through
gap or conduit, along existing
wiring harness
Route cable along trunk
wall and into cabin
Use a Diunt plastic putty
knife or similar blunt tool
to lift edge of interior
trim and tuck cable -
under mm. Continue '. fi‘i’;‘§r°3°:|mgfr ,
towards iront oi vehic|e ‘, D V ,
,"C0ntinue routlnq cable
under trim or carpet
towards Iront 0! vehicle
Route cable from trunk
under interior trim. Into
cabin and (awards Iront
oi vehicie
Vehicle Installation
Continue rnutinq cable under
carpet or console to radio location
Coil excess
cable under
Pull carpet
carpet or mat
or mat hack
Bring cable out
from trim
Bring Cable out 1mm trim
and route under carpet to
dashhuard or console
TlPl Always be carelul to include enouqh slack In your cable la
accommodate open doors or trunk lids. use things typically lounu around
me home, like electrical tape, In secure cables in areas sn mat hinges do uni
pinch the cable with the Goon Nlde any excess came in the trim.
Sedan/Coupe WIth Antenna Placed at tho Rear of the Root:
1 Feed the antenna Cable lrom the antenna underneath the rubber molding
around the rear window Us! a blunt plastic Duttv knife or similar blunt
tool to lift the rubber molding around the rear window and tuck the
antenna Cable underneath the molding. Route the antenna Cable around
and down the window to the lowest point. If your rear window does not
have rubber molcing, we recommend consulting a prolessianal Installer,
2 Route the antenna cable out of the window molding and into the rubber
weather stripping araunu the trunk opening. Litt the weather stripping
from the opening and tuck the cable inside it. then replace the weather
stripping. To avoid sharp bends in the cable. run the cable inside the
weather stripping lor a law inches. then remove the cable from the
weather stripping inside the trunk. Keep the cable away from hinges,
gears. eta, that could damage it.
3 Route the cable out from the rubber weather stripping and along the
trunk wall. Continue routing the cable into the vehicle cabin through a
conduit or along an existing wiring harness
4 Route the cable through the main cabin area under the interior trim.
towards the front ol the vehicle.
Use a blunt plastic putty knife
or similar blunt tool to lift the
plastlc trim just enough to tuck
the cable under underneath,
Avoid side airbag locations
on back plllars and above the
doors. Airbag locations are
marked with "sRS" logos. Be
careful not to crimp or cut the
cable.
Vehicle |nstallation
5 Brim; the cable out from the trim near the front of the cabin and route
it under the carpet toward the dashboard or console. Coll any excess
table In a hidden location, such as under the carpet, keepinl] it away from
any Vehicle pedals Or controls. Secure the excess cable with wire ties
(purchased separatelv),
6 Bring the end of the cable out at the PowerConnect Vehicle Duck location.
Leave voursell enough cable so you can easily connect it to the antenna
connector Ol the deck
7 Continue with “Step 5: Connect the Magnetic Mount Antenna and
PowerCOnnect Power Adapter" on paqe 37.
Sedan/Coupe With Antenna Placed at the Front of the R00!
1 Feed the antenna cable from the antenna underneath the rubber molding
around the windshield. Use a blunt plastic puttv knife or similar blunt tool
to Iilt the rubber molding around the windshield and tuck the antenna
cable underneath the molding. Route the antenna Cable around and down
the windshield to the lowest point.
2 At the lowest corner oi the windshield, route the cable out of the
windshield molding and into the rubber weather stripping around the
door opening. Lift the weather
stripping lram the upenlnq and
tuck the cable inslde it. then
replace the weather stripping.
Run the cable Inside oi the
weather stripplnq to the hottam
ot the door opening,
3 Pull the Cable out oi the
weather stripping at the bottom
of the door opening and route it under the carpfi toward the dashboard,
Call any excess cable in a hidden location, such as under the carpet,
keeping it away lram any vehicle pedals or controls. SECUrE the excess
cable with wire ties.
‘ Bring the and Of the cable out at the Paws/Connect Vehicle Dock locationt
Leave vaursell enough cable so you can easily connect it In the antenna
connector of the deck
5 Continue with “Step 51Cunnect the Magnetic Mount Antenna and
Puwercimnect Power Adapter" on page 37.
Sport Utility Vehicle (SUV)
1 Feed the antenna cable underneath the rubber weather stripplnq al the
rear tailgate window/door and route the cable along the rear hatcht tilt
the weather stripping from the opening and tuck the cable inside it, then
replace the weather stripping. Pull the cable out from weather stripping
and route it into the cabin unuer the interior trim. Avoid hinges cr gears
that could crimp or cut the cable.
2 Route the cable through the
suv's maln cabin area under
the lnterior trim, towargs the
front at the vehicle. Use a blunt
plastlc putty knile or similar
blunt tool to tilt the plastic trim
just enough to tuck the cable
under underneath. Avoid side
airbag locatlons an hack pillars
and above the doors. Airbag
locations are marked with "SRS"
Vehicle |nstallation
logos. Be careful not to crimp or cut the cable.
3 Erlng the cable out from the trim near the front 0! the cabln and route
it under the Carpet toward the dashboard or console. Coil any excess
cable in a hidden location, such as under the carpet. keeping it away lrcvrn
any vehicle pedals or Controls. Secure the excess cable with wire ties
(purchased separatelyx
4 Bring the end of the Cable out at the PawerConnect Vehicle Dock location.
Leave yourself enouqh cable 50 you can easily connect it to the antenna
connector of the dock.
5 Continue with "Step 5: Connect the Magnetic Mount Antenna and
PowerConnect Power Adapter" on page 37.
Convertible
1 Bring the antenna Cable from the antenna into the trunk at the front edge
cl the trunk lid. Keep any bends in the cable loose, Tape or tie the cable
along the inside of the trunk lid to the trunk lid hinge struto
2 Allow enough slack in the cable so the trunk lio can easily open and close
ano keep the cable away irpm hinges, gears. eta, that could crimp or cut
it. Route the cable along the trunk wall
and into the cabin through a conduit or
along an existlnq wirlnq harness.
3 Route the cable through the main
cabin area under the interior trim.
towards the lront oi the vehicle use
a blunt plastlc putty Knlte or similar
blunt tool to Iilt the plastic trim
Just enuuqh to tuck the cable under
underneath. Avoid side airbaq locations on back pillars and above the
doors Alrbag Iocatinns are marked with "SRS" qu05. Be careful not to
crimp or cut the cable.
4 Bring the cable out from me trim near the front of the cabin and route
it under the carpet toward the dashboard er console, Coil any excess
cable in a hidden location, sum as under me carpet, keeping it away lrbrn
any vehicle pedals or controls. Secure me Excess cable with wire ties
(purchased separately).
5 Bring the end at the Cable out at the PowerConnect Vehicle Dock location.
Leave yourself enough cable so you can easily Connect it to the antenna
connector of the deck,
8 Continue with "Step 5: Connect the Magnetic Mount Antenna and
PowerConneCt Power Adapter" on page 37.
Pickup Truck
1 Use a blunt plastic putty kniie or Similar blunt tool to lilt the rubber
molding around the windshield and tuck
the antenna cable underneath it.
2 Continue tucking the cable underneath the
wlndshield molding around the windshield
to the lowest cornen
3 At the lnwest carrier of the wim‘lshield.
route the cable But of the windshield
molding and into the rubber weather
strlpplnq around the door opening. Lift
the weather stripplnq lrnm the opening
and tuck the cable inside it, then replace
Vehicle Installation
the weather strlpplnq. Run the cahte inside or the weather strlpping to the
bottom at the door opening.
4 Pull tne cable out of the weather stripping at the bottom of the door
apening and route it under the carpet toward the dashboarde coii any
excess cable in a hidden location, such as under the carpet. keeping it
away from any vehicle pedals or controls Secure the excess cable with
wire ties.
5 Bring the end at the cable out at the PowerConnect Vehicle Dock iocation.
Leave yourse‘i enough cable so vou can easily connect it to the antenna
connector DI the deck.
6 Continue with "Step 5: Connect the Magnetic Mount Antenna and
FowerConnett Power Adapter" on page 37.
Step 5: Connect the Magnetic Mount Antenna and
PowerConnect Power Adapter
1 Plug the Magnetic Mount Antenna into the
s|lver ANY connectur on (he PowerConnect
Vehicle Dock.
2 Insert the PowerConnect Power Adapter into 1
your vehicle's cigarette lighter or power adapter //
socket ‘
3 PM!) the Powerconnect Power Adapter into
the red PWR Connecmr on the dock.
Vehicle Installation
Step 6: Connect the Audio
To play KM audio through your Vehicle's stereo or FM radio, fleclde on one of the
following audio connection options:
. Optlon 1: Best: Use the provided Aux In Cable il your vehicle's stereo
system has an auxiliary input connection or jack. Refer to your vehicle's
owners manual to find the location oi the auxiliary input jack, or consult the
vehicle dealer.
YIPI The auxiliary input tack may be located on the lace plate 01 the vehicle
radio, on the back or the radio. anywhere on the lronl dash panel. inside the
glove compartment, or inside the center console in between the lront seats.
- Option 1: Better: Use a cassette Adapter il your vehicle has a built-
in cassette player. Cassette Adapters are sold separately and can be
purchased from an electronics retailer. or go to www.siriusxm.com/
accessories.
- option 3: Good: Use the Fowemonnect feature oi XMH. PowerConnect plays
the audio through your vehicle's FM radio.
' Option 4: Best: Use the PM Direct Adayter. If none of the previous three
audio connection options will work in your Vehicle, the" you will need to
use the FM Direct Adapter (FMDA) (sold separately). The FMDA needs to
be installed by a prolessional installer and directly connects XMH to your
vehicle’s FM radio. To learn more. check with the retailer where you bought
your Radio, or 90 to www,siriusxmxomlaccessories.
Follow the installation Instructions in the next several sections for the audio
connection option that you have selected.
Optlon 1: Aux In Cable lnstallatlon Instructions
1 Plug one end of the Aux In Cable into the green AUDIO connector on the
dock
2 Plug the other end into the
auxiliary input jack of your
vehicle's stereo system.
3 Attach the dock to the mount. 42
4 Insert your XMH into the dock. f
5 Power on your XMH hv
pressing the Power buflun.
5 Be sure the vehicle is outside
and the antenna has a Clear view D! the sky. Veri'v
that you are receiving the XM signal. There shauld
at least be one bar on the lower left Corner of the
main display screen that denotes antenna signal
strength You can also press menu and then turn
the Rotary Knob tn scroll to and highlight Slqnal
Indicator. Press the Select button The Satellite
and Terrestrial bars show the strength of the
signal being receivedl ll the signal reception is
Vehicle Instal|ation
good, press and hold menu to return to
the main display screen.
1 Ensure XMH is tuned to channel 1.
the XM Preview channel. Upon power
up. XMH should tune to channel 1 by
default, when rt's not yet activated. ll
it's not on channel 1, reler to “Listening
to Satellite Radio" on page 55 to
learn about how to tune a channel.
Stgnal lndrcnror
3 Turn on your vehicle's stereo system.
Set it to play from the auxl|iary input
source. You should hear XM channell
through your vehicle's stereo system.
You are now ready to activate your
XMH. 8 07643-2112
9 The audio level output of XMH can be “WSW W”
increased or decreased as necessary to
match the audio levels or other sources
in your vehicle. Refer to "Set Audio
Level" on page 31.
«ml
it the signal reception is good, showing at least one bar in the lower left corner
or the dlsplay, but there is no XM audio, be sure the vehicle's stereo system is set
to the auxiliary input source (step 4). Also be sure that the audio level is set high
enough to be heard (step 5). Reler to "Troubleshooting” on page 92 ror additional
help.
Opticn 2: Cassette Adapter Instalhtlon |nsttuctions
1 Plug the cassette Adapter into the ween AuDIo connector on the deck
2 lnsert the Cassette Adapter into the vehic|e's cassette deck. You may
neefl to turn on your vehicle's stereo system In order to do 554
3 Attach the dock tn the mount.
4 Insert your XMH into the dock.
5 Power on your XMH by
pressing the Power button.
6 Be sure the vehicle is outside
and the antenna has a clear
view oi the sky. Verify that
yuu are receiving the XM signal. There should at
least be one bar on the lower left corner al the
main display screen that denotes antenna signal
strength You can also press menu and then turn
the Rotary Knob to scroll to and highlight Slgnnl
ineleatur, Press the Select button. The Satellite
and Terrestrlal bars show the strength at the
slqnal being received. If the signal reception is
Vehicle Installation
good. press and hold menu to return (0 the main display screen.
1 Ensure XMH ls tuned to channel 1.
the XM Preview channel. Upon power
up, XMH shoulo tune to channel 1 by
default, when it's not yet activated. lt
it's not on channel 1, roler to "Listening
to Satellite Radio" on page 55 to
learn about how to tune a channel.
signal lrlljlmlul
3 Turn on vour vehicle's stereo system.
Set it to play from the auxiliary input
source. You should hear XM channel}
through your vehicle's stereo system.
You are now ready to activate your
XMH,
(«w»)
9 The audio level output of XMH can be
increased or decreased as necessary to 800-643 2112
match the audio levels of other sources
in your vehicle. Refer to "Set Audio
Level" on page 3L
Sllluskm zoln
lt the signal reception is good, showing at
least one bar in the lawer Ieit corner of the
display, but there is no XM audio. be sure the vehicle's stereo system is set to the
cassette source (step 4). Also be sure that the audio level is set high enough to
be heard (step 5). Refer to ”Troubleshooting" on page 92 ior additional help.
Option 3: PuwerConnect Installation instructions
1 Attach the dock to the mount.
2 insert your XMH into the dock.
3 Power on your XMH by
pressing the Power button.
4 Be sure the vehicle is outsige
and the antenna has a clear
view of the sky. Verify that
you are receiving the xm signal. There should at
least be one bar on the lower left corner of the
main display screen that denotes antenna signal
strength. YOU can also press menu and then turn
the Rotary Knob to scroll to and highlight signal
indicator. Press the Select button. The Satellite
and Terrestrial bars show the strength of the
signal being received. it the signal reception is
good. press and hold menu to return to the main
display screen.
5 You'll first need to find an available FM
channel. An available FM channel is one
that's not being used by an FM radio
station in your area When you tune
your FM radio to an available channel,
you should only hear static or silence
- not talk or music, We recommend
one of the following methods (0 find an
available FM channel:
Signal illdtrqlur
5 Ensure XMH is tuned to Channel 1.
5. Use the SirlusXM FM Channel Finder at www.s|rIusxm.com/rmchannelt
Go to the website and enter your Zip coder The Channel Finder wlll
suggest a list of available FM channels in your area. For convenience,
write down or print out the list.
OR
a. Manually tune through your local FM channels on your vehicle's FM radio.
Locate and create a list of channels that aren't being used by any FM radio
station. Write down the list. Once you have created your list at available
FM channels, you will need to find the one that provides the best match for
XMH.
“Pl You'll need to use the 'Manual' tune lunctioh on your vehtcle’s FM radio to
tune through every FM channel one-oy~one. Turn on your vehicle's FM radio.
start at 551 and use the ‘Manual' tune lunrtion on your vehicle's FM radio to
tune through each FM channel ane'bv-one (881 followed by 98.3 etc.) to locate
channels that aren‘t being used by a local FM radio station. Write dawn each FM
channel that has only static or silence on it, until you reach 107.9.
the XM Preview Channel, Upon power
up. XMH should tune to channel i by
default. when It’s not vet activated. ll
it's not on channel 1, refer to "Listening _ A
to Satellite Radio" on page 55 to 800 643 2112
learn about how to tune a Channel. ‘NIUS’ 7“
Pick the first FM Channel on your llsl
from step 5. Turn on your Vehicle's FM
radio (it you have not already done so)
and tune it to this FM ChanneL
More! lt you are using the Vehicle Duck train the universal xnress Car Kit
ihsteao ol the Powerconnect vehicle Dock whlth came with your XMH, you will
have to disable Aux Detect. Reler to "Using the Vehicle
Duck From the Universal Xwess Car Kit“ on pace as,
and complete the adfllllanal instructions helore
conlinuinq with the next step. The audio connection will
be through your vehicle's FM radio, but it is not
PowerConneet.
MAYCH m CHANNELS
a Set your XMH to transmit on the same FM Channels
FM channel that you have selected in
step 7; FM 1 97.9 currehl
' Press menu. FM 2
, Turn the Rotary Knoh to scroll
to and highlight FM Settinqs and FM 3
press the Select button.
iii. FM Channels will tie hiqhiiqhteu. If FM 4
it is not highlighted, turn the Rotary
Knob to scroll to and highlight m
Channels. Press the Select button,
iv. Turn the Rotary Knob to scroll to
and highlight the storage location
m z and press the Select button,
v. Tune to the available FM channel
ou choose in step 3. Press ( and
to tune in steps at .z, i.e.. 99.3

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 45
Creator                         : Hewlett Packard MFP
Create Date                     : 0000:01:01 00:00:00
Author                          : 
Producer                        : 
Title                           : 
Subject                         : 

EXIF Metadata provided by EXIF.tools