Sony Group BM153 Bluetooth Module User Manual SPEC BM153 V4 6 10012013
Sony Corporation Bluetooth Module SPEC BM153 V4 6 10012013
Contents
- 1. BM153_User Manual_REV3
- 2. BM153_User Manual_REV 65298
BM153_User Manual_REV3
® Product Specification BM153 Class 2 Multimedia Module Features: • • • • • • • • • • • • • • • • • Qualified Bluetooth Spec. V3.0 (V2.1+EDR)Compliant Class 2 type Output Power Support Firmware Upgrade USB 1.1 and UART Host Interface Multi-Configurable I2S, PCM or SPDIF Interface Integrated Switched-Mode Regulator Integrated Battery Charger Integrated Microphone bias Integrated LED Driver Built in 16-bit Stereo Codec- 95dB SNR for DAC Factory configurable to either 1.8V or 3.3V supply. Supports up to 32Mbits of External Flash Memory (16Mbits Typical Requirement) Enhanced Audibility and Noise Cancellation PCB material:FR4 PCB Surface treatment: Immersion gold Size: 21mm x 13.5 mm x 2.35mm Weight: 0.8g CSR, BC57E687C Jan. 2013 Product Description: The BM153 is a Class 2 Bluetooth sub-system using BlueCore5Multimedia External chipset from leading Bluetooth chipset supplier Cambridge Silicon Radio. BM153 interfaces to 8Mbit of external Flash memory When used with the CSR Bluetooth software stack, it provides a fully compliant Bluetooth system to V3.0 of the specification for data and voice communications The module and device firmware is fully compliant with the Bluetooth specification V3.0 Applications: • • • • • • System Architecture • Hands-free Car Kit Stereo Headset AV Headphones Echo Cancellation High Performance Mono Headsets Analogue and USB Multimedia Dongles Wireless Speakers Specifications: Operating Frequency Band Bluetooth Specification Output Power Class Max. Output Power Date Rate Channel No. Modulation Type Operating Voltage Host Interface Audio Interface Flash Memory Size Dimension Specifications are subject to change without prior notice Spec-BM153-V4.6 2.4GHz ~ 2.48GHz unlicensed ISM band BT V3.0 (V2.1+EDR) Class 2 2.5mW 3Mbps 79 GFSK π/4 DQPSK 8DPSK 1.8V / 3.3V USB 1.1 or UART PCM, I2S, SPDIF 8M,16M, or 32Mbits 21mm (L) x 13.5 (W) mm x 2.35mm (H) Page 1 of 7 www.sunitec-cn.com ® Product Specification Electrical Characteristics Absolute Maximum Rating Storage Temperature Supply Voltage, (V_CHG) Min -40°C -0.30V Max +85°C +6.5V Recommended Operating Conditions Operating Temperature Range Supply Voltage, (V_BAT) Supply Voltage, (V_CHG) Min -20°C 2.5V 4.5V Max +70°C 4.2V 5.75V Power Consumption SCO Connection HV3 (30ms interval sniff mode) SCO Connection HV1 ACL Data Transfer 115.2Kbps UART no traffic (Master) ACL Data Transfer 115.2Kbps UART no traffic (Slave) Units mA mA mA mA Average mA mA mA TBD TBD TBD 21 40 4.4 15 CODEC Microphone inputs and ADC/channel DAC and loudspeaker driver, no signal/channel Digital audio processing subsystem VBAT = 4.2V; f = 2.441GHz; T=20°C RF Characteristics Receiver Sensitivity at 0.1% BER Maximum Receiver Signal C/I Co-Channel Adjacent Channel Selectivity C/I -1MHz 2nd Adjacent Channel Selectivity C/I -2MHz 3rd Adjacent Channel Selectivity C/I -3MHz Image Rejection C/I Units dBm dBm dB dB dB dB dB Min -20 Typ -90 -10 -6 -38 -45 -16 Max -86 11 -30 -40 -9 Bluetooth Spec ≤-70 ≥ -20 ≤11 ≤0 ≤-30 ≤-40 ≤-9 Units dBm dB dB KHz dBm dBm Min 16 Typ 24 0.5 940 -36 -45 Max 1000 -20 -40 Bluetooth Spec -6 to +4 > 16 <1000 ≤-20 ≤-40 VBAT = 4.2V; f = 2.4441GHz; T=20°C Transmitter RF Output Power RF Power Control Range RF Power Range Control Resolution 20dB Bandwidth for Modulated Carrier 2nd Adjacent Channel Power (+/- 2MHz) 3rd Adjacent Channel Power (+/- 3MHz) VBAT = 4.2V; f = 2.4441GHz; T=20°C All specifications including pinouts and electrical specifications may be changed without prior notice Spec-BM153-V4.6 Page 2 of 7 www.sunitec-cn.com ® Product Specification Pin Configurations PIN NO. NAME AIO1 AIO0 RESET 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 GND PIO9 PIO10 PIO11 PIO12 PIO13 PIO14 PIO15 GND VDD VDD VDD_USB +1V8 GND USB_DP USB_DN UART_RTS UART_CTS UART_RX UART_TX PCM_IN PCM_SYNC PCM_CLK PCM_OUT SPI_CSB SPI_MISO SPI_CLK SPI_MOSI VRE_IN VDD_BAT TYPE Bi-directional Bi-directional CMOS input with weak internal pull-up GND Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional GND Power Power Power Power GND Bi-directional Bi-directional CMOS Output CMOS Input CMOS Input CMOS Output CMOS Input Bi-directional Bi-directional CMOS Output CMOS Input CMOS Output CMOS Input CMOS Input Analogue Battery terminal +ve 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 GND VDD_CHG LED1 LED0 GND SPK_L_N SPK_L_P SPK_R_N SPK_R_P GND_S MIC_BIAS MIC_B_P MIC_B_N MIC_A_P MIC_A_N GND PIO0 PIO1 PIO2 PIO3 PIO4 PIO5 PIO6 PIO7 PIO8 GND RF-IN GND GND Charger input Open drain output Open drain output GND Analogue Analogue Analogue Analogue GND_S Analogue Analogue Analogue Analogue Analogue GND Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional GND RF GND Spec-BM153-V4.6 FUNCTION Programmable input/output line Programmable input/output line Reset if low. Input debounced so must be low for >5ms to cause a reset Ground Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Ground +3.3V Supply Connect to +1V8 Positive supply for UART/USB ports, Connect to VDD +1.8V Supply Ground USB Data Plus USB Data Minus UART Request To Send (Active Low) UART Clear To Send (Active Low) UART Data Input (Active High) UART Data Output (Active High) Synchronous Data Input Synchronous Data Sync Synchronous Data Clock Synchronous Data Output Chip Select For Synchronous Serial Interface (Active Low) Serial Peripheral Interface Data Output Serial Peripheral Interface Clock Serial Peripheral Interface Data Input Take high to enable switch-mode regulator Lithium ion/polymer battery positive terminal. Battery charger output and input to switch-mode regulator Ground Lithium ion/polymer battery charger input LED Driver LED Driver Ground Speaker output negative, left Speaker output positive, left Speaker output negative, right Speaker output positive, right Anlogue Signal Ground Microphone bias Microphone input positive, right Microphone input negative, right Microphone input positive, left Microphone input negative, left Ground Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Ground RF Interface Ground Page 3 of 7 RE-MARK For 3.3V Version For 1.8V Version www.sunitec-cn.com ® Product Specification Recommended Layout patterns: Spec-BM153-V4.6 Page 4 of 7 www.sunitec-cn.com ® Product Specification Recommended Reflow Temperature Profile: Key features of the profile: -Initial Ramp=1-2.5℃/sec to 175℃ equilibrium -Equilibrium time=60 to 80 seconds -Ramp to Maximum temperature (250℃)=3℃/sec Max -Time above liquidus temperature(217℃): 45 - 90 seconds -Device absolute maximum reflow temperature: 250℃ MAC Address: Each Module has his MAC Address 001D DF XXXXXX Concerning the dimension of the tab,only printing the last six letters of the LAP on the module. 13.0 mm 5.0 mm xxxxxx The tab code pastes style: Spec-BM153-V4.6 Page 5 of 7 www.sunitec-cn.com ® Product Specification QDL Certificate Spec-BM153-V4.6 Page 6 of 7 www.sunitec-cn.com ® Product Specification Ordering Information No Items Ordering Code (Class 2) BC05mm-ext Module-3V3 BM153 BC05mm-ext Module-3V3 BM153-08 BC05mm-ext Module-3V3 BM153-32 BC05mm-ext Module Test Kit BM153 TK Description 16Mbit Flash Operating Voltage is 3.3V 8Mbit Flash Operating Voltage is 3.3V 32Mbit Flash Operating Voltage is 3.3V Test kit base BM153 Document References References Version Specifications of the Bluetooth System BlueCore5-Multimedia External Product Data Sheet V2.1+EDR, 26 July 2007 CS-121064-DSP2 15 July 2008 Document History Revision Date Draft V0.1 V1.0 V2.0 V3.0 V4.0 V4.1 V4.2 V4.3 V4.4 V4.5 V4.6 2006-12-12 2007-04-12 2008-09-11 2008-09-19 2009-05-22 2009-07-30 2009-08-22 2009-12-02 2011-7-1 2011-12-19 2013-01-10 History First release Update from Revision V1.0 Update from Revision V2.0 Update from V2.0+EDR compliant to V2.1+EDR compliant Update from printing MAC address “UAP” to “LAP” Remove BC57E687B-ITB-E4 from BOM Modify page 3 PIN OUT mistake (Swap AIO0 and AIO1) Add more order information Add more order information BM153-32 Add BM153 Test board Contact Information Sunitec Enterprise Co., Ltd. Head Office: 3F.,No.98-1,Mincyuan Rd Sindian City, Taipei County 231,Taiwan Tel: 886-2-82191696 Fax: 886-2-82191676 http://www.sunitec.com.tw Spec-BM153-V4.6 China Factory: No.2,Qilin Road 2,Run Tang Ind., Dan-Keng Village Fu Ming Community, Guan-lan Town, BaoAn District, Shenzhen GuangDong China Tel: 86-755-29802983 Fax: 86-755-29802984 E-mail: sales@sunitec-cn.com or project@sunitec-cn.com Http://www.sunitec-cn.com Page 7 of 7 www.sunitec-cn.com Interrnal Photo SSony Corpora ation Persoonal Audio Syystem [Model:SRS‐X5] Interrnal Photo SSony Corpora ation Persoonal Audio Syystem [Model:SR RS‐X5 Interrnal Photo SSony Corpora ation Persoonal Audio Syystem [Model:SR RS‐X5 All iss ok ,fixed thee speaker and d front plasticc case. As follow photo Nextt: fixed the iro on net and backboard.as ffollow photo; Now w, one SRS‐‐x5 is fixed OK K. as follow p hoto. FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. The end host device should bear the label which indicate "Contains FCC ID:AK8BM153" or "Contains IC:409B-BM153".
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Modify Date : 2013:11:29 11:39:47+08:00 Create Date : 2013:08:29 22:48:18+08:00 Metadata Date : 2013:11:29 11:39:47+08:00 Format : application/pdf Title : Microsoft Word - SPEC-BM153-V4.6 10012013.doc Creator : Administrator Document ID : uuid:99d1f2e8-6c48-475b-b8ae-81d702f7cd37 Instance ID : uuid:8d09d736-d5ec-4e77-a495-acff45b966f4 Has XFA : No Page Count : 16 Author : AdministratorEXIF Metadata provided by EXIF.tools