Symbol Technologies WSAP5100 WLAN Access Port User Manual 1 jpg

Download:
Mirror Download [FCC.gov]
Document ID	468326
Application ID	l5vg2vYrazte+gGksbHgfA==
Document Description	installation manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	118.63kB (1482905 bits)
Date Submitted	2004-09-13 00:00:00
Date Available	2004-09-08 00:00:00
Creation Date	2004-09-08 17:19:50
Producing Software	Acrobat Distiller 6.0.1 (Windows)
Document Lastmod	2004-09-08 17:22:13
Document Title	1.jpg
Document Creator	PScript5.dll Version 5.2
Document Author:	Agaren Yang

SPECIFICATIONS ML-2499-BYGA2-0!
2.4 - 2.5 Gllz Antenna
Model ML-2499'BYGA2'01 “shining Arres'er and Cable Assemblies
Frequency MHz 24002500 ASSEMBLY AND INSTALLATION
Gain: 13.9 dBi '
Number Elements: 15
Front-toBack Ratio: 18 dB
E—Flane (3 dB beamwidth): 30°
H—Flane (3 dB beamwidth): 34°
"Radiating Element Brass
Impededance (Ohms): 50
Antenna Conneclon Type N (n
Antenna Weight lb. (kg): 1.25 (56)
Mounting: Articulating mount
Dimensions in.(cm): ZS-IIZ X 3-314 x 1~112(S7.3 x 9.5 X 3.8)
Enclosure: UV Stable Polycarbonate
Mast Diameter Max. in (cm): 2—118 (5.4)
Antenna Cable in (cm): 12 (30.5)
Important Wanting: Two pails of weep holes are provided in
the radome one for vertical mounting and one for horizontal
mDunling. You must fill Ihe unused pair of weep holes with
adhesive dots prior to mounting or unwanted leakage into the
radome may result {see instructions),
APPLICATION "7
The ML-2499—BYGA2—01 is a complete kit consisting of a
highly directional iselement Yagi enclosed in a UV stable
weatherproof radome. This antenna providfi extended point-
to-point link coverage. or sharply focused zonal coverage for
2.4-GHz ISM applications
SAFETYa
The ML»2499~BYGA2—01 and all associated equipment
should be installed in accordance with applicable local and
national electrical code guidelines to ensure safe operation.
ANTENNA LOCATION
The antenna may be mounted at interioforexbfiorlocations.
For link installations. a “neat-sight path between antennas
works best. Although 2.4 GHZ signals penetrate cubical
dividers and interior partitions with little attenuation, reinforwd
block walls, banks of metal cabinets, or steel shelving may
attenuate signals or cause multipath, a condition where
reflected signals interfere with the primary signal. Because
antenna beam width Is restricted to 15degrees each side of
center. the P0241SSNA must be aimed accurately during
installation in order to provide optimum gain and best
performance.
GENERAL MOUNTING INFORMATION
- The P0241 SSNA is equipped with an articulating mount,
gifg'nififii'y'm‘?“ Inc' and may be oriented for vertical or horizontal polarization. lt
Huntsville, Nv11742-1aoo accommodates mast sizes up to 2-1I8»inches (4.76 cm).
951533 310:
WEEP HOLES
Two sets of weep holes are provided in the P6241 5NA
radome one set is required for horizontal mounting and
one set for vertical mounting. Prior to installation, the
unused pair of weep holes must be plugged with adhesive
dots to prevent leakage. Two small adhesive dots are
supplied with each antenna for this purpose. Weep-hole
locations are shown in Figure-A.
1.Vertical Mounting: When mounting vertically, find two
weep holes on the broad flat side of the radome and
cover with adhesive dots
2. Horizontal Mounting. When mounting honzontally, find
two (2) weep holes on the narrow edge of the radome
and cover with adhesive dots.
When adhesive dots are applied check to ensure holes
are fully closed
FIGURE A
Coax Routing: During installation, avoid any sharp bend
or kink in the feed line. Also, avoid bending coax close to
the radome where it may apply pressure to the wall of the
cable grommet and compromise the water seal. Route
coax downward—or provide a drip loop to ensure rainwater
accumulating on the jacket flows away from the cable
grommet in the radome.
ASSEMBLY
1. Prior to mounting, find the arrow sticker on the radome.
When mounting vertically, the arrow should always point
upward. When mounting horizontally. the arrow sticker
should always be on top of the
radome. This positioning is required
(a) to ensure weep holes fall on the
bottom of the antenna. and (b) to
ensure proper phasing when
multiple antennas are used with a
harness.
nouns B”
ASSEMBLY cont.
2. Orient for the desired polarization and install the antenna
base against the mast using the two U-bolts (04), four
hex nuts (18), four lock washers (19) and two V-blooks
(63) provided in hardware kit
3. If the antenna has an articulating mount, install the
antenna ball into position and tilt tor the desired elevation
angle (Figure-D). Tighten the socket screw with the
supplied wrench.
4. Rotate antenna to the desired directional position and
tighten all hardware.
FIGURE C
FIGURE D
System grounding and lightning protection are essential
especially for exterior-mounted antennas exposed to the
elements (refer to the National Electrical Code). Never install
an antenna where it may fall and contact electrical lines.
KEY Pm DISPLAY SIZE
U—BOLT 5115215 x 3-114’ x 2-7/rs'
010115 55 HEX sits' 18
owns SPLlTLOCK 5115‘
WASHER
195725 . v anACKEr
3 t
ADHESIVE
JUMPER KIT INSTALLATION (OPTIONAL)
The jumper and arrester kits provide a convenient way to
set up your link. For best results. tighten connectors securely
and encapsulate exterior junctions with sealant tape. When
routing cable. use drip loops to guide rain water away from
the LAC4 and back of the antenna
CANM1ZBRENMLA
The Cushcraft lightning
arrester kit has been designed
to provide in—Iine lightning
protection and can be easily
integrated into the Cushcraft
extension cable jumper system.
The pre-made low loss cable
assembly features high quality
cable and N male connectors
and easy to use connector
wraps. It offers the user a fast,
convenient method to remotely
mount the antenna at a
distance of up to 100 feet from
the access point or bridge.
CANMGOOLNM
7 énsnnaoufnh 245er
CASNMtZODNM 10m
E‘AsnM‘ofiNM‘ Jolt.
CASNMBOONM soft.
Figure E LAC4 Installation on PC24158NA
CANM600LNM (50 ft)
. Brldgel
- an L009s “i Access Polnt
\.
f Sealant_ \
l Tape
LAC4 LIGHTNING ARRESTER (OPTIONAL)
For best results, install the LAC4 in close proximity to a
low-resistance ground at a point where the coaxial cable
enters the building (see Photo-1). in most cases, one B—foot
rod driven into moist soil—or multiple mds bonded together
will provide adequate grounding (see National Electrical
Code guidelines)
To connect the LAC4 to ground, use a very short and
direct run of #10 solid copper wire (or equivalent) For
exterior installations, weatherproof coax connectors with a
suitable mastic or mbberized tape to prevent water incursion
(see Photo1).
Be sure to install in an accessible location that permits
periodic inspection and (as needed) replacement of the
gas cartridge. Provide drip loops in cables to prevent water
from entering the building (see Photo 2).
Photo 1
‘L/
Sealant Tape , r
or Rubberized Protestant
Photo 2
v, Drip Loops fit
/I' ‘i
\\
Important Note: A good ground system is essential for
proper operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 3
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:45fd4302-e784-44d7-96b4-a319c1b6ab8c
Producer                        : Acrobat Distiller 6.0.1 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2004:09:08 17:22:13+08:00
Create Date                     : 2004:09:08 17:19:50+08:00
Metadata Date                   : 2004:09:08 17:22:13+08:00
Document ID                     : uuid:707e59bb-30d2-43ee-b4ab-787f3bde9b3c
Format                          : application/pdf
Title                           : 1.jpg
Creator                         : Agaren Yang
Author                          : Agaren Yang

EXIF Metadata provided by EXIF.tools