TAKAYA RP69W01 User Manual Operating Manual
TAKAYA Corporation Operating Manual
UserManual.wiki
>
TAKAYA
>
RP69W01 User Manual
>
Operating Manual
Contents
1.
Operating Manual
2.
Manual ClassB declaration
3.
Correspondence Reference Number 7066
4.
Reply to Reference Number 7066
Operating Manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![RX-W1 Page 4[1] Wetness Sensing System(1) Overview’†Œp‹@ŒÅ’èŒ^ŽóM‹@Œg‘ÑŒ^•\ Ž¦‹@‘—M‹@—¾•êŽº‹ŽºThis Wetness Sensing System is comprised with transmitters, transpondersand receivers, which inform caregivers of sensing moisture in a diaper. Oncewetness sensor incorporated into diaper is aware of moisture, the transmitterincluding sensor puts out the signal to the transponder and then to the receiver.Handy-receiverStation-receiver(option)TransmitterTransponder](https://usermanual.wiki/TAKAYA/RP69W01.Operating-Manual/User-Guide-30360-Page-4.png)
![RX-W1 Page 254.Cominucations Protocol[PC] [Receiver][ Sensing DataTransfer]The Receivertransfers sensinginformation andbattery shutoffinformation.It transfers thedata periodicallyeach 5sec. …[BCC][CR]Transmitter ID (4-digits) which is sensingmoisture or batteryshutoff is transferredafter [:][K], and thenTransmitter status (”1”= Sensing moisture, ”2”= Battery shutoff, “3” =“1” and “2”) istransferred as single-digit. When multipleIDs or status istransferred, they arebroken by and added[BCC][CR] at the end.When there are nothingof transmittinginformation,[K][BCC][CR] aretransferred.BCC Calculating Methods:(STX) K(CMD) 0101(ID) 1(DATA) CN(BCC) Calculating RangeIt gets the SUM from CMD to DATA and divides into MSB 4bits and LSB 4bits, and then adds 40H and converts into 2 bytes word as hexadecimal.Example 1‘’‘’‘’414243LSBMSBExample 2 ‘’‘’‘’‘’‘’‘’‘’‘’‘’‘’‘’LSBMSB](https://usermanual.wiki/TAKAYA/RP69W01.Operating-Manual/User-Guide-30360-Page-25.png)
![RX-W1 Page 26ID TypesTransmitter IDTransmitter ID “0608” is 4-digit number, first 2-digit is Area ID and last two-digit isindividual unique ID.16 types of Area ID“01””16”(“01””10”[Hex])99 types of Unique ID“01””99”(“01””63”[Hex])Transmitter Clone ModeFig.4-1 CONNECTION OF CLONING UNITConnect the cloning unit like above chart, and start up PC and then run “HyperTerminal” of Windows accessory.Fig.4.2 Initial window of Hyper TerminalAfter running Hyper Terminal, the following window will open. Set as below.TRANSMITTERPC underWindows 95 or98RS232CStraight cableDCV](https://usermanual.wiki/TAKAYA/RP69W01.Operating-Manual/User-Guide-30360-Page-26.png)
![RX-W1 Page 29The following Transmitter start-up screen (Fig.4-4) will be displayed after settingCommunication Port and Communication protocol and insert a battery.Fig.4-4 Transmitter start-up screenAt this point when pushing C key within 5sec, the following screen (Fig.4-5) isdisplayed and Mode Set can be changed. Pushing Enter key terminates the setting.Fig.4-5Mode Set for Transmitter###### TX69W01 Ver.1.0 ######**** << Current Mode Status >> **** Current Detection=[ Capacitor ] 1.ID No. = 0112 2.Resistor Detection Time = 3 (s) 3.Capacitor Detection Time = 10 (s) 4.Transmission Qty = 01 5.STOP Time = 10 (s) 6.Serial Modulation Qty = 06Change Mode Set = [C] ? Execute = [Enter] ? (Note: No Key, Auto Execute after 5 sec.)Current setting statusof Transmitter**** << Current Mode Status >> **** Current Detection=[ Capacitor ] 1.ID No. = 0112 2.Resistor Detection Time = 3 (s) 3.Capacitor Detection Time = 10 (s) 4.Transmission Qty = 01 5.STOP Time = 10 (s) 6.Serial Modulation Qty = 06**** << Mode Set >> **** [1] = Country Select [2] = ID No. [3] = Resistor Detection Time [4] = Capacitor Detection Time [5] = Transmission Qty [6] = STOP Time [7] = Serial Modulation Qty [0] = ENDSelect [1]-[7],[0] and Press [Enter]>Mode Set forTransmitter](https://usermanual.wiki/TAKAYA/RP69W01.Operating-Manual/User-Guide-30360-Page-29.png)
![RX-W1 Page 30Country Set (Select [] in Fig. 4-5)Fig.4-6Country SetTransmitter ID Set (Select [] in Fig.4-5)Fig.4-7Transmitter ID SetSetting of Resistor Detection Time. (Select [] in Fig.4-5)Fig.4-8 Setting of Resistor Detection TimeSetting of Capacitor Detection Time. (Select [] in Fig.4-5)Fig.4-9 Setting of Capacitor Detection Time**** << Country Set >> **** [ESC]=STOPCountry = USA[1]=USA [2]=JAPANInput [1]or[2] ? and Press [Enter]>1Current countryCountry changed**** << ID No. Set >> **** [ESC]=STOPID No. = 0112Input ID No. [0000]-[9999] ? and Press [Enter]>0101Current IDID changed**** << Resistor Detection Time Set >> ****[ESC]=STOPResistor Detection Time = 3 (s)Input [1]-[9] ? and Press [Enter]>2Current Detection TimeDetection Time changedunit: [sec]**** << Capacitor Detection Time Set >> ****[ESC]=STOPCapacitor Detection Time = 10 (s)Input [01]-[99] ? and Press [Enter]>09Current Detection TimeDetection Time changedunit: [sec]](https://usermanual.wiki/TAKAYA/RP69W01.Operating-Manual/User-Guide-30360-Page-30.png)
![RX-W1 Page 31Setting of Transmission number of times. (Select [] in Fig.4-5)Fig.4-10 Setting of Transmission number of timesSetting of Transmission Stop Time. (Select [] in Fig.4-5)Fig.4-11 Setting of Transmission Stop TimeSetting of Modulation number of times. (Select [] in Fig.4-5)Fig.4-12 Setting of Modulation number of timesSelect [] in Fig. 4-5, and then CLONING MODE will be terminated.After terminated CLONINGMODE, it returns to Normal Mode.Fig.4-13 CLONINGMODE Termination**** << Transmission Qty Set >> **** [ESC]=STOPTransmission Qty = 01Input [01] ? and Press [Enter]>01Current Transmissionnumber of timesIn case of USA, Transmissionnumber of times is only one, andit is impossible to change.**** << Stop Time Set >> **** [ESC]=STOPStop Time = 10 (s)Input [10]-[99] ? and Press [Enter]>11Current Stop TimeIn case of USA, Stop time can bechanged from 10sec to 99sec.**** << Serial Modulation Qty Set >> **** [ESC]=STOPSerial Modulation Qty = 06Input [01]-[06] ? and Press [Enter]>05Current Modulationnumber of timesIn case of USA, Modulationnumber of times can be changedfrom 01 to 06.Select [1]-[7],[0] and Press [Enter]>0**** << End of Mode Set >> ****](https://usermanual.wiki/TAKAYA/RP69W01.Operating-Manual/User-Guide-30360-Page-31.png)
![RX-W1 Page 32Transponder Clone ModeFig.4-14 CONNECTION OF CLONING UNITConnect the cloning unit like above chart, and start up PC and then run “HyperTerminal” of Windows accessory.When TRANSPONDER turned ON, the following screen (Fig.4-15) is displayed.Fig.4-15 Transponder set-up screenAt this point when pushing C key within 5sec, the following screen (Fig.4-16) isdisplayed and Mode Set can be changed. Pushing Enter key terminates the setting.Fig.4-16Setting for TransponderInsert to CN2 ofTRANSPONDERPC underWindows 95 or98RS232CStraight CableConversion Cable###### RP69W01 Ver.1.0 ###### 1. Repeater Retry Qty = [3] (x10sec)Change Mode Set = [C] ? Execute = [Enter] ?Note: No Key, Auto Execute after 5 sec.Current Status ofTransponder setting **** << Current Mode Status >> **** 1. Repeater Retry Qty = [3] (x10sec)**** << Mode Set >> **** [1] = Repeater Retry Qty Set [0] = ENDSelect [1],[0] and Press [Enter]>1](https://usermanual.wiki/TAKAYA/RP69W01.Operating-Manual/User-Guide-30360-Page-32.png)
![RX-W1 Page 33Setting of Transponder Re-try number of times (Select [] in Fig.4-16)It means even the signal from Transponder is aborted, it holds IDs for re-trynumber of times multiplied by 10sec.Fig.4-17 Setting of Transponder Re-try number of timesSelect [] in Fig. 4-5, and then CLONING MODE will be terminated.After terminated CLONINGMODE, it returns to Normal Mode.Fig.4-18 CLONINGMODE Termination>1Repeater Retry Qty = [3]Repeater Retry Qty [1]-[9]x10s =4Current Retry number of timesRetry number of times changed.unit: [10sec]**** << Mode Set >> **** [1] = Repeater Retry Qty Set [0] = ENDSelect [1],[0] and Press [Enter]>0Mode set end.](https://usermanual.wiki/TAKAYA/RP69W01.Operating-Manual/User-Guide-30360-Page-33.png)
![RX-W1 Page 34Receiver Clone ModeFig.4-19 CONNECTION OF CLONING UNITConnect the cloning unit like above chart, and start up PC and then run “Hyper Terminal” of Windows accessory.When Receiver turned ON, the following screen (Fig.4-20) is displayed.Fig.4-20 Initial screen of ReceiverRECEIVER PC underWindows 95 or98RS232CStraight###### RX69W01 Ver.1.0 ###### 1. Melody Channel for Area Id Area Id 1 = Melody [01] (Ch) Area Id 2 = Melody [02] (Ch) Area Id 3 = Melody [03] (Ch) Area Id 4 = Melody [04] (Ch) Area Id 5 = Melody [05] (Ch) Area Id 6 = Melody [06] (Ch) Area Id 7 = Melody [07] (Ch) Area Id 8 = Melody [08] (Ch) Area Id 9 = Melody [09] (Ch) Area Id 10 = Melody [03] (Ch) Area Id 11 = Melody [03] (Ch) Area Id 12 = Melody [02] (Ch) Area Id 13 = Melody [01] (Ch) Area Id 14 = Melody [14] (Ch) Area Id 15 = Melody [15] (Ch) Area Id 16 = Melody [16] (Ch) 2. Melody Output = Repeat 3. Display switching time for multiple alarmed ID'S = [3]x0.5 (sec) 4. Dispaly holding time for alarmed ID = [3]x10 (sec)Change Mode Set = [C] ? Execution = [Enter] ?Note: No Key, Auto Execution after 5 sec.Current Status ofReceiver setting](https://usermanual.wiki/TAKAYA/RP69W01.Operating-Manual/User-Guide-30360-Page-34.png)
![RX-W1 Page 35At this point when pushing C key within 5sec, the following screen (Fig.4-5) isdisplayed and Mode Set can be changed. Pushing Enter key terminates the setting.Fig.4-21 Mode Set for ReceiverSetting Melody Channel for Area ID (Select [] in Fig.4-21)Fig.4-22 Setting Melody Channel for Area ID **** << Current Mode Status >> **** 1. Melody Channel for Area Id Area Id 1 = Melody [01] (Ch) Area Id 2 = Melody [02] (Ch) Area Id 3 = Melody [03] (Ch) Area Id 4 = Melody [04] (Ch) Area Id 5 = Melody [05] (Ch) Area Id 6 = Melody [06] (Ch) Area Id 7 = Melody [07] (Ch) Area Id 8 = Melody [08] (Ch) Area Id 9 = Melody [09] (Ch) Area Id 10 = Melody [03] (Ch) Area Id 11 = Melody [03] (Ch) Area Id 12 = Melody [02] (Ch) Area Id 13 = Melody [01] (Ch) Area Id 14 = Melody [14] (Ch) Area Id 15 = Melody [15] (Ch) Area Id 16 = Melody [16] (Ch) 2. Melody Output = Repeat 3. Display switching time for multiple alarmed ID'S = [3]x0.5 (sec) 4. Dispaly holding time for alarmed ID = [3]x10 (sec)**** << Set of Mode >> **** Cancel=ESC [1] = Melody Channel for Area Id [2] = Melody Output [3] = Display switching time for multiple alarmed IDS [4] = Display holding time for alarmed IDSelect [1]-[4] and Press [Enter]>1Current Status ofReceiver setting **** << Change Melody for Area Id & confirm each Melodies >> ****Cancel=ESC [1] = Change Melody for Area Id [2] = Confirm each melodiesSelect [1]-[2] and Press [Enter]>1Confirm MelodyChange Melody](https://usermanual.wiki/TAKAYA/RP69W01.Operating-Manual/User-Guide-30360-Page-35.png)
![RX-W1 Page 36Change Melody for Area Id (Select [] in Fig.4-22)Fig.4-23 Setting Melody Channel for Area ID**** << Change Melody for Area Id >> **** Cancel=ESC [01] = Setting Area Id 1 [02] = Setting Area Id 2 [03] = Setting Area Id 3 [04] = Setting Area Id 4 [05] = Setting Area Id 5 [06] = Setting Area Id 6 [07] = Setting Area Id 7 [08] = Setting Area Id 8 [09] = Setting Area Id 9 [10] = Setting Area Id 10 [11] = Setting Area Id 11 [12] = Setting Area Id 12 [13] = Setting Area Id 13 [14] = Setting Area Id 14 [15] = Setting Area Id 15 [16] = Setting Area Id 16Select [01]-[16] and Press [Enter]>01Area ID for changing](https://usermanual.wiki/TAKAYA/RP69W01.Operating-Manual/User-Guide-30360-Page-36.png)
![RX-W1 Page 37Change Melody for Area Id (Select [] in Fig.4-23)Fig.4-24 Setting Melody Channel for Area ID**** << Change Melody for Area Id >> **** Cancel=ESC**** << Melody Name >> **** [01] = Yankee Doodle [02] = Oh Bury Me Not On The Lone Prairie [03] = Oh! Susanna [04] = Under The Spreading Chestnut Tree [05] = Grandfathers Clock [06] = Chitty Chitty Bang Bang [07] = De Camptown Races [08] = If Youre Happy And You Know It, Clap Your Hands [09] = Mary Had A Little Lamb [10] = Edelweiss [11] = Bridge Over Troubled Water [12] = I have Been Working On The Railroad [13] = Do-Re-Mi [14] = One Sunny Day [15] = Aloha Oe [16] = Battle Hymn of The Republic [17] = AlarmSelect [01]-[17] and Press [Enter] Area Id 1 = Melody [01] (Ch)Melody Channel for Area Id 1 =>01List of Melody nameMelody ID No. changed](https://usermanual.wiki/TAKAYA/RP69W01.Operating-Manual/User-Guide-30360-Page-37.png)
![RX-W1 Page 38Confirm each melodies (Select [] Confirm in Fig.4-22)Fig.4-24 Melody ConfirmationSetting of Melody Output Method (Select [] in Fig.4-21)Fig.4-25 Melody output method Set**** << Confirm each melodies >> **** Cancel=ESC**** << Melody Name >> **** [01] = Yankee Doodle [02] = Oh Bury Me Not On The Lone Prairie [03] = Oh! Susanna [04] = Under The Spreading Chestnut Tree [05] = Grandfathers Clock [06] = Chitty Chitty Bang Bang [07] = De Camptown Races [08] = If Youre Happy And You Know It, Clap Your Hands [09] = Mary Had A Little Lamb [10] = Edelweiss [11] = Bridge Over Troubled Water [12] = I have Been Working On The Railroad [13] = Do-Re-Mi [14] = One Sunny Day [15] = Aloha Oe [16] = Battle Hymn of The Republic [17] = AlarmSelect [01]-[17] and Press [Enter] Current Melody Ch= [01] Request Melody Ch=>01List of Melody nameMelody number confirmed**** << Melody Output >> **** Cancel=ESC [0] = One Shot [1] = RepeatSelect [0]-[1] and Press [Enter]Melody Output = RepeatMelody Output =>1Current Melody output methodMelody Output method for changing](https://usermanual.wiki/TAKAYA/RP69W01.Operating-Manual/User-Guide-30360-Page-38.png)
![RX-W1 Page 39Display switching time for multiple ID’s Set (Select [] in Fig.4-21)Fig.4-26 Changing Display holding time for Multiple IDsDisplay holding time for alarmed ID Set (Select [] in Fig.4-21)Fig.4-27 Changing Display holding time**** << Display switching time for multiple alarmed IDS >> ****Cancel=ESC [1] = 0.5 Sec [2] = 1.0 Sec [3] = 1.5 Sec [4] = 2.0 Sec [5] = 2.5 Sec [6] = 3.0 Sec [7] = 3.5 Sec [8] = 4.0 Sec [9] = 4.5 SecSelect [1]-[9] and Press [Enter]Display switching time for multiple alarmed IDS = [3]x0.5 (sec)Display switching time for multiple alarmed IDS =>6Current holding time for displayHolding time for display changed**** << Display holding time for alarmed ID >> **** Cancel=ESC [1] = 10 Sec [2] = 20 Sec [3] = 30 Sec [4] = 40 Sec [5] = 50 Sec [6] = 60 Sec [7] = 70 Sec [8] = 80 Sec [9] = 90 SecSelect [1]-[9] and Press [Enter]Display holding time for alarmed ID = [3]x10 (sec)Display holding time for alarmed ID =>3Current holding time for displayHolding time for display changed](https://usermanual.wiki/TAKAYA/RP69W01.Operating-Manual/User-Guide-30360-Page-39.png)
![RX-W1 Page 40Push [Esc] in Fig. 4-21, and then CLONING MODE will be terminated.After terminated CLONINGMODE, it returns to Normal Mode.Fig.4-28 CLONINGMODE Termination**** << Set of Mode >> **** Cancel=ESC [1] = Melody Channel for Area Id [2] = Melody Output [3] = Display switching time for multiple alarmed IDS [4] = Display holding time for alarmed IDSelect [1]-[4] and Press [Enter]>**** << End of Mode Set >> ****](https://usermanual.wiki/TAKAYA/RP69W01.Operating-Manual/User-Guide-30360-Page-40.png)