TAKAYA TR3-C202-A0-8 RFID Reader/Writer User Manual TDR MNL C202 A0 8 EN 101

TAKAYA Corporation RFID Reader/Writer TDR MNL C202 A0 8 EN 101

Contents

User Manual

User’s Manual TR3-C202-A0-8 Manual No.TDR-MNL-C202-A0-8-EN-101
Manual No.TDR-MNL-C202-A0-8-EN-101 TAKAYA RFID TR3 Series Introduction Thank you for purchasing a TR3-C202-A0-8 RFID READER/WRITER. Be sure to read this manual before using the product. After reading it, store the manual in a convenient place for future reference.
Manual No.TDR-MNL-C202-A0-8-EN-101 TAKAYA RFID TR3 Series Regulations and Standards FCC This product is conform to the FCC standards. FCC Rules (Federal Communications Commission) This product complies with Part 15 Subpart C of the FCC Rules. FCC ID : MK4TR3-C202-A0-8 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off an on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC NOTICE This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The following sentence has to be displayed on the outside of the device in which the transmitter module is installed : “Contains FCC ID: MK4TR3-C202-A0-8” Japan Radio Law Equipment using high frequencies: Inductive Reading/Writing Communications Equipment Conforming standards: Inductive Reading/Writing Communications Equipment; Standard: ARIB STD-T82 Tags This product can communicate the standard tags of ISO/IEC15693 and ISO/IEC18000-3(Mode1). Supports Manufacturer Tag-it HF-I Texas Instruments my-d Infineon Technologies I･CODE SLI NXP Semiconductors MB89R118 FUJITSU Japan RoHS is support Restriction of Hazardous Substances Waste Dispose of the Products as industrial waste.
Manual No.TDR-MNL-C202-A0-8-EN-101 TAKAYA RFID TR3 Series Safety Precautions The following symbols are used in this manual to indicate precautions that must be observed to ensure safe use of this product. The precautions provided here contain important safety information. Be sure to observe these precautions. The following signal words are used in this manual. Failure to comply with a WARNING may result in serious injury or death. Failure to comply with a CAUTION may result in injury to the operator, or damage to the items involved. Be sure to observe the following precautions to ensure safe use of the Products. Decomposition of this product and cable, repair, remodeling, please strictly prohibited. There is the possibility of fire or electric shock injuries. This product is using the RFID reader writer radio equipment. Therefore, depending on where the applications you use may affect medical equipment. To minimize the impact of medical equipment for use, please observe the following countermeasure. The Japan Automatic Identification Systems Association (JAISA) guidelines are as follows: RFID antennas from implanted cardiac pacemakers or other medical devices please 22cm apart. We recommend that you paste "RFID sticker" at equipment. Be sure to observe the following precautions to ensure safe use of the Products. Installation and storage environment 1. Do not use the Products in sunlight. 2. Do not use the Products in environment of spray of water, oil or chemicals. 3. Do not use the Products in environments with flammable, explosive, or corrosive gasses. 4. Do not use the Products in environment of hot humid. 5. Do not use the Products in environment of vibration or shock. 6. Do not use the Products in environment of condensation. 7. Do not use the Products in environment of around the metal is covered. 8. Do not use the Products in environment of high temperature. 9. Do not use the Products in environment that has a device that generates magnetic field and shock voltage. 10. Do not use the Products in unstable place. 11. If there is failure, discontinue use immediately, please contact us or the distributor. Installation 1. Turn off the power before installation or removing. 2. The following effects may not work correctly. ･ Near 13.56MHz radio device ･ Near speakers , Inverter, motor and Plasma Display 3. The communication range may vary due to environment and conditions. ← RFID Sticker
Manual No.TDR-MNL-C202-A0-8-EN-101 TAKAYA RFID TR3 Series Contents 1 Product Overview ........................................................................................................................................................................................................................................................................................................................................................................................................................ 1111 1.1 Features .............................................................................................................................................. 1 2 Names of Parts and Functions .................................................................................................................................................................................................................................................................................................................................................... 2222 2.1 TR3-C202-A0-8 ................................................................................................................................... 2 2.2 Antenna .............................................................................................................................................. 3 2.2.1 TR3-A202 ........................................................................................................................................ 3 2.2.2 TR3-A302 ........................................................................................................................................ 4 2.2.3 TR3-A401 ........................................................................................................................................ 4 3 Installation and connection .................................................................................................................................................................................................................................................................................................................................................................... 5555 3.1 Installation into a host device .............................................................................................................. 5 3.1.1 Installation from the Front.................................................................................................................. 5 3.2 Antenna installation into a host device................................................................................................. 6 3.2.1 Screw holes ...................................................................................................................................... 6 3.2.2 Guide ............................................................................................................................................... 6 3.3 Connection .......................................................................................................................................... 7 3.3.1 Attaching the Cable and Antenna........................................................................................................ 7 3.3.2 Direct connection to the Host Device Interface .................................................................................... 7 3.3.3 Using the interface board to connect to the Host Device Interface.......................................................... 8 4 Specifications .................................................................................................................................................................................................................................................................................................................................................................................................................................................... 9999 4.1 TR3-C202-A0-8 ................................................................................................................................... 9 4.2 Antenna ............................................................................................................................................ 14 4.2.1 TR3-A202 ...................................................................................................................................... 14 4.2.2 TR3-A302 ...................................................................................................................................... 15 4.2.3 TR3-A401 ...................................................................................................................................... 16 4.3 Cable................................................................................................................................................. 17 5 Maintenance ................................................................................................................................................................................................................................................................................................................................................................................................................................................ 18181818 Revision History.................................................................................................................................................................................................................................................................................................................................................................................................................................................... 19191919 3.1.2 Installation from the Front deleted........................................................................................................ 19
Manual No.TDR-MNL-C202-A0-8-EN-101 1 Product Overview 1.1 Features 1 TAKAYA RFID TR3 Series 1 Product Overview 1.1 Features This product uses the 13.56MHz frequency. This product is the electromagnetic induction type non-contact IC can read and write RFID tag data. This Product is designed to be embedded and integrated within OEM devices and finished products such as label printers, cashless payment terminals or any other device that can benefit from integrated RFID capabilities. ■ Conform to international standards ISO/IEC15693 and ISO/IEC18000-3(Mode1) is supports. ■ Rich Products  Various interface RS-232C, USB, TCP/IP.  Antennas of various sizes ■ Software  TR3-series common communication protocol  Software Development Kit ■ Multiplexer Select the RF output. ■ Useful  Continuous inventory mode UID of the tag automatically sends Host Device.  RDLoop mode UID or User Data of the tag automatically sends Host Device. For more information please refer to the TR3-PROTOCOL manual. ■ Environmentally EU RoHS(2002/95/EC) Support Antenna CPU Memory RF-ASIC READER/WRITER Load Settings Save Settings Interface Tags Host Device Interface RS-232C、LAN(TCP/IP)、USB Communications Multiplexer Antenna Antenna UART(CMOS Level)
Manual No.TDR-MNL-C202-A0-8-EN-101 2 Names of Parts and Functions 2.1 TR3-C202-A0-8 2 TAKAYA RFID TR3 Series 2 Names of Parts and Functions 2.1 TR3-C202-A0-8 No Name Description ① Screw holes M3 holes ② STUD NUTS Internally, substrate is fixed at stud nats. M3 Screw hole depth : 3mm ③ LED1 Displays the status of this product. ④ CN1 This connector is for connection to the host. ⑤ Nameplate Production numbers, will be 8-digit serial number. ⑥ FCC ID stickers ⑦ CH1 to CH8 Connect the antenna cable. Please connect form CH1. ① ③ ④ ⑦ ⑥ ⑤ ② Model Name Serial number：＊＊＊＊＊＊＊＊(F)
Manual No.TDR-MNL-C202-A0-8-EN-101 2 Names of Parts and Functions 2.2 Antenna 3 TAKAYA RFID TR3 Series 2.2 Antenna 2.2.1 TR3-A202 No Name Description ① CN1 Connect the antenna cable. ② Nameplate Production numbers, will be 8-digit serial number. ③ Inspection mark ④ Screw holes M3 holes ④ ① ② ③ Model Name Serial number：＊＊＊＊＊＊＊＊(F)
Manual No.TDR-MNL-C202-A0-8-EN-101 2 Names of Parts and Functions 2.2 Antenna 4 TAKAYA RFID TR3 Series 2.2.2 TR3-A302 No Name Description ① Inspection mark ② Screw holes M3 holes ③ Nameplate Production numbers, will be 8-digit serial number. ④ CN1 Connect the antenna cable. 2.2.3 TR3-A401 No Name Description ① CN1 Connect the antenna cable. ② Nameplate Production numbers, will be 8-digit serial number. ③ Inspection mark ② ③ ④ ① Model Name Serial number：＊＊＊＊＊＊＊＊(F) ① ② ③ Model Name Serial number：＊＊＊＊＊＊＊＊(F)
Manual No.TDR-MNL-C202-A0-8-EN-101 3 Installation and connection 3.1 Installation into a host device 5 TAKAYA RFID TR3 Series 3 Installation and connection 3.1 Installation into a host device 3.1.1 Installation from the Front M3 Screw Four, M3 holes Host Device
Manual No.TDR-MNL-C202-A0-8-EN-101 3 Installation and connection 3.2 Antenna installation into a host device 6 TAKAYA RFID TR3 Series 3.2 Antenna installation into a host device 3.2.1 Screw holes 3.2.2 Guide TR3-A401 is recommended that you set up a guide on fixed-like the figure below. TR3-A401 M3 Screw Host Device
Manual No.TDR-MNL-C202-A0-8-EN-101 3 Installation and connection 3.3 Connection 7 TAKAYA RFID TR3 Series 3.3 Connection This product will connect with the antenna and antenna cables. This product connects with Host Device that direct connection or connect using our interface. 3.3.1 Attaching the Cable and Antenna 3.3.2 Direct connection to the Host Device Interface Please prepare to the interface harness. Host Device Interface harness TR3-C202-A0-8 TR3-C202-A0-8 Antenna Antenna Cable Host Device Interface Host Device
Manual No.TDR-MNL-C202-A0-8-EN-101 3 Installation and connection 3.3 Connection 8 TAKAYA RFID TR3 Series Host Device 3.3.3 Using the interface board to connect to the Host Device Interface Interface board, please contact us. TR3-C202-A0-8 Interface Cable Interface board Interface harness Host Device Interface
Manual No.TDR-MNL-C202-A0-8-EN-101 4 Specifications 4.1 TR3-C202-A0-8 9 TAKAYA RFID TR3 Series 4 Specifications 4.1 TR3-C202-A0-8 ■ Specifications Specifications Item Parameter Japan Radio Law ARIB STD-T82 FCC FCC Part 15 Subpart C FCC ID : MK4TR3-C202-A0-8 Applicable Standards RoHS EU RoHS(2002/95/EC) Supports Carrier frequency 13.56MHz ±50ppm(Ta=25℃) or less Transmit power or power range 10 to 100mW ± 20% (Transmit power range varies with input voltage.) Standards ISO/IEC 15693、ISO/IEC18000-3(Mode1) Tags Tag-it HF-I, my-d, I･CODE SLI, MB89R118(※1) Data rate Speed Data rate 1/4 26.48kbps Reader/Writer⇒Tag 1/256 1.65kbps Tag⇒Reader/Writer 26.69kbps Modulation Parameter Reader/Writer⇒Tag ASK 10%(※2) / ASK 100% Tag⇒Reader/Writer ASK, FSK Radio Frequency Anti-collision Support ※1：Tag-it HF-I is a registered trademark of Texas Instruments Incorporated. my-d is a registered trademark of Infineon Technologies AG. I･CODE SLI is a registered trademark of NXP Semiconductors. MB89R118 is a registered trademark of FUJITSU Japan. ※2：initialization
Manual No.TDR-MNL-C202-A0-8-EN-101 4 Specifications 4.1 TR3-C202-A0-8 10 TAKAYA RFID TR3 Series Specifications Item Parameter Command Please refer to the TR3-C202 Protocol-Manual. Host Interface UART(CMOS) Item Parameter Speed 9600bps 19200bps(※2) 38400bps Data bits 8 Parity None Stop bit 1 Flow control None Controll LED1 1pc (3 colors, red/green/orange) CN1 Connector : JST S10B-PH-SM4-TB(LF)(SN) Housing : JST PHR-10 Contact : JST SPH-002T-P0.5S Pin assignment Pin No. Symbol Function 1 VCC Power 2 VCC Power 3 GND GND 4 GND GND 5 Rx Received data signal 6 Tx Transmitted data signal 7 VCC2 Power output 8 IO1 Input/Output or Detection signal output H : Detection 9 IO2 Input/Output or Trigger input L : Trigger ON 10 IO3 Input/Output Connector CH1 to CH8 Connector : JST S2B-PH-SM4-TB(LF)(SN) Housing : JST PHR-2 Contact : JST SPH-002T-P0.5S Pin assignment Pin No. Symbol Function 1 RF Analog signal 2 GND GND ※2：initialization
Manual No.TDR-MNL-C202-A0-8-EN-101 4 Specifications 4.1 TR3-C202-A0-8 11 TAKAYA RFID TR3 Series Specifications Item Parameter Dimensions (W x D x H) 103.6 x 103 x 23.3mm Wight approx. 240g Mechanical data Installation M3 Screw Screw is not included. Electrical data Power Supply Voltage ：+3.3± 10%, +5V ± 10% Current consumption ：approx. 160mA(VDD=5.0V) Carrier off ：approx. 60mA(VDD=5.0V) Power down mode ：approx. 50mA(VDD=5.0V) Consumption ：max 1.0W(VDD=5.0V) Temperature Operating range 0 to 55 degree Humidity Operating range 30 to 80%RH Temperature Storage range 0 to 55 degree Ambient Conditions Humidity Storage range 30 to 80%RH Other Accessories None
Manual No.TDR-MNL-C202-A0-8-EN-101 4 Specifications 4.1 TR3-C202-A0-8 12 TAKAYA RFID TR3 Series ■ Dimensions Unit：mm Tolerance：±1mm ( )is Recommended Dimension
Manual No.TDR-MNL-C202-A0-8-EN-101 4 Specifications 4.1 TR3-C202-A0-8 13 TAKAYA RFID TR3 Series ■ Connections Names Model Notes TR3-A202 TR3-A302 Antenna TR3-A401 Cable TR3-AC-2A-*** *** puts the cable length. 0.5m ~ 3m cable are available. TR3-IF-1C RS232C interface TR3-IF-N1 TCP/IP interface Interface board TR3-IF-U1 USB interface ■ Electrical Characteristics(CN1、CN3)  VDD=5.0V Item Condition MIN TYP MAX Unit H input voltage 2.5 5.0 V L input voltage 0 1.0 V H output voltage IOH=-5mA,-20mA 3.0 V L output voltage IOL=5mA,20mA 2.0 V Pull-up resistor 25.0 50.0 100.0 kΩ  VDD=3.3V Item Condition MIN TYP MAX Unit H input voltage 1.815 3.3 V L input voltage 0 0.66 V H output voltage IOH=-5mA,-20mA 3.0 V L output voltage IOL=5mA,20mA 2.0 V Pull-up resistor 25.0 50.0 100.0 kΩ ・TX, RX, IO1, IO2 and IO3 is, Pull-up resistor has been connected. ・TX, RX, IO1, IO2 and IO3 is, 100 ohm resistor has been connected. Output port, LED is not driven. If the LED drive, please use the digital transistors.
Manual No.TDR-MNL-C202-A0-8-EN-101 4 Specifications 4.2 Antenna 14 TAKAYA RFID TR3 Series 4.2 Antenna 4.2.1 TR3-A202 ■ Specifications Specifications Item Parameter Applicable Standards RoHS EU RoHS(2002/95/EC) Support Resonant frequency 13.56MHz ±40kHz(Ta=25℃) Antenna Communication distance Max 10cm (Communication distance depends on the environment.) Connector CN1 Connector : JST S2B-PH-SM4-TB(LF)(SN) Housing : JST PHR-2 Contact : JST SPH-002T-P0.5S Pin assignment Pin No. Symbol Function 1 RF Analog signal 2 GND GND Dimensions (W x D x H) 60 x 65 x 9.1 mm Wight approx. 11g Mechanical data Installation M3 Screw Screw is not included. Temperature Operating range 0 to 55 degree Humidity Operating range 30 to 80%RH Temperature Storage range 0 to 55 degree Ambient Conditions Humidity Storage range 30 to 80%RH Other Accessories RFID Sticker 1 sheet Model Name : SEL41400L ■ Dimensions Unit：mm Tolerance：±1mm Substrate thickness : 1.6mm
Manual No.TDR-MNL-C202-A0-8-EN-101 4 Specifications 4.2 Antenna 15 TAKAYA RFID TR3 Series 4.2.2 TR3-A302 ■ Specifications Specifications Item Parameter Applicable Standards RoHS EU RoHS(2002/95/EC) Support Resonant frequency 13.56MHz ±40kHz(Ta=25℃) Antenna Communication distance Max 7cm (Communication distance depends on the environment.) Connector CN1 Connector : JST S2B-PH-SM4-TB(LF)(SN) Housing : JST PHR-2 Contact : JST SPH-002T-P0.5S Pin assignment Pin No. Symbol Function 1 RF Analog signal 2 GND GND Dimensions (W x D x H) 15 x 52.5 x 9.1 mm Wight approx. 3g Mechanical data Installation M3 Screw Screw is not included. Temperature Operating range 0 to 55 degree Humidity Operating range 30 to 80%RH Temperature Storage range 0 to 55 degree Ambient Conditions Humidity Storage range 30 to 80%RH Other Accessories RFID Sticker 1 sheet Model Name : SEL41400L ■ Dimensions Unit：mm Tolerance：±1mm Substrate thickness : 1.6mm
Manual No.TDR-MNL-C202-A0-8-EN-101 4 Specifications 4.2 Antenna 16 TAKAYA RFID TR3 Series 4.2.3 TR3-A401 ■ Specifications Specifications Item Parameter Applicable Standards RoHS EU RoHS(2002/95/EC) Support Resonant frequency 13.56MHz ±40kHz(Ta=25℃) Antenna Communication distance Max 5cm (Communication distance depends on the environment.) Connector CN1 Connector : JST S2B-PH-K-S(LF)(SN) Housing : JST PHR-2 Contact : JST SPH-002T-P0.5S Pin assignment Pin No. Symbol Function 1 RF Analog signal 2 GND GND Dimensions (W x D x H) 15 x 30 x 9.1 mm Wight approx. 2g Mechanical data Installation M3 Screw Screw is not included. Temperature Operating range 0 to 55 degree Humidity Operating range 30 to 80%RH Temperature Storage range 0 to 55 degree Ambient Conditions Humidity Storage range 30 to 80%RH Other Accessories RFID Sticker 1 sheet Model Name : SEL41400L ■ Dimensions Unit：mm Tolerance：±1mm Substrate thickness : 1.0mm
Manual No.TDR-MNL-C202-A0-8-EN-101 4 Specifications 4.3 Cable 17 TAKAYA RFID TR3 Series 4.3 Cable ■ Model Name ■ Specifications Item Parameter RoHS EU RoHS(2002/95/EC) Support Linetype Coaxial cable 1.5D-2V Connector PH-PH Cable loss 0.5M : approx. 0.043dB 3M : approx. 0.255dB ■ Dimensions ( )is Recommended Dimension (Cable length) TR3-AC-2A-*** Enter the cable length(Unit:m) 0.5M～3M
Manual No.TDR-MNL-C202-A0-8-EN-101 18 TAKAYA RFID TR3 Series 5 Maintenance This product is mainly used in electronic components and semiconductors. Therefore, the long-term stable operation, the environment and conditions are expected to defect, as shown below. • Device degradation due to overvoltage and overcurrent. • Device degradation due to high temperature and long-term stress. • Poor contact of the connector and cause deterioration of insulation by moisture or dust. • Connector corrosion by corrosive gases. In order to use this product at its best, please conduct routine or periodic inspections. Item Maintenance Criteria Temperature Temperature Operating range 0 to 55 degree Humidity Humidity Operating range 30 to 80%RH Enclosure rating Check the dusty None Ambient conditions Corrosive Check the corrosion None Input Check the voltage Power Voltage fluctuation Check the Voltage fluctuation Input Voltage : DC +3.3 ± 10%, +5V ± 10% Check the Screw Product Check the Connector Checking and verifying Attachment Cable Check the Cable break None Performance Check the Performance Work
Manual No.TDR-MNL-C202-A0-8-EN-101 19 TAKAYA RFID TR3 Series Revision History Revision code Date Revised contents 1.00 2010/4/16 Original production 1.01 2011/03/03 3.1.2 Installation from the Front deleted. 4.1 TR3-C202-A0-8 Add to 3.3V input voltage.
20 [URL] http://www.takaya.co.jp/ [Mail] rfid@takaya.co.jp

Navigation menu