Thrane and Thrane A S 6300 SAILOR 6311 MF/HF 150W DSC CLass A FCC User Manual AlarmPanel

Thrane & Thrane A/S SAILOR 6311 MF/HF 150W DSC CLass A FCC AlarmPanel

manual alarm panel

INSTALLATION AND USER MANUALSAILOR 6101 and SAILOR 6103Alarm Panel
SAILOR 6101 and SAILOR 6103Alarm PanelInstallation and user manualDocument number: 98-130981-DraftA7Release date: July 5, 2010
DisclaimerAny responsibility or liability for loss or damage in connection with the use of this product and the accompanying documentation is disclaimed by Thrane & Thrane. The information in this manual is provided for information purposes only, is subject to change without notice and may contain errors or inaccuracies. Manuals issued by Thrane & Thrane are periodically revised and updated. Anyone relying on this information should acquire the most current version e.g. from http://www.thrane.com or from the distributor. Thrane & Thrane is not responsible for the content or accuracy of any translations or reproductions, in whole or in part, of this manual from any other source.Copyright© 2010 Thrane & Thrane A/S. All rights reserved.Trademark Acknowledgements•Thrane & Thrane is a registered trademark of Thrane & Thrane A/S in the European Union and the United States.•Inmarsat is a registered trademark of the International Maritime Satellite Organisation (IMSO) and is licensed by IMSO to Inmarsat Limited and Inmarsat Ventures plc. •SAILOR is a registered trademark of Thrane & Thrane A/S in the European Union, the United States and other countries.• Other product and company names mentioned in this manual may be trademarks or trade names of their respective owners.
iiiSafety summary 1The following general safety precautions must be observed during all phases of operation, service and repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture and intended use of the equipment. Thrane & Thrane assumes no liability for the customer's failure to comply with these requirements.DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHEREDo not operate the equipment in the presence of flammable gases or fumes. Operation of any electrical equipment in such an environment constitutes a definite safety hazard. KEEP AWAY FROM LIVE CIRCUITSOperating personnel must not remove equipment covers. Component replacement and internal adjustment must be made by qualified maintenance personnel. Do not service the unit with the power cable connected. Always disconnect and discharge circuits before touching them.DO NOT SUBSTITUTE PARTS OR MODIFY EQUIPMENT Because of the danger of introducing additional hazards, do not substitute parts or perform any unauthorized modification to the equipment.COMPASS SAFE DISTANCEMinimum compass safe distance: 1 m.Failure to comply with the rules above will void the warranty!
ivAbout the manual 2Intended readersThis manual is an installation and user manual for the two types of Alarm Panel, SAILOR 6101A and SAILOR 6103A. The manual is intended primarily for installers of the system and service personnel. Personnel installing or servicing the system must be properly trained and authorized by Thrane & Thrane. It is important that you observe all safety requirements listed in the beginning of this manual, and install the system according to the guidelines in this manual. Manual overviewThis manual has the following chapters:•Introduction - a short description of the two types of Alarm Panel.•Using the Alarm Panel - a short guide on how to use the Alarm Panel to send distress alerts, receive distress or urgency messages, set up light and sound and test the Alarm Panel.•Installing the Alarm Panel - a description of how to unpack, store and install the Alarm Panel.•Connecting cables - descriptions and pin-out for the connectors, guidelines for connecting the Alarm Panel and descriptions of the buttons.•Service and repair - a short description of how to handle defective units.•Specifications - technical specifications for the Alarm Panel.
vTable of ContentsChapter 1 IntroductionThe Alarm Panel ................................................................. 1Chapter 2 Using the Alarm PanelStarting up the Alarm Panel ...............................................6Sending a Distress alert .....................................................7Receiving Distress or Urgency messages ............................8Displaying faults ................................................................9General functions ............................................................. 10Chapter 1 Installing the Alarm PanelInitial inspection ...............................................................14Storage .............................................................................14To install the Alarm Panel .................................................15Chapter 2 Connecting cablesConnectors .......................................................................22Cable requirements ..........................................................26Connecting the Alarm Panel .............................................27Connecting multiple Alarm Panels ...................................28Chapter 3 Service and repairIntroduction .....................................................................29Repacking for shipment ...................................................30
Table of ContentsviApp. A SpecificationsGeneral specifications ...................................................... 31Glossary .........................................................................................33Index .........................................................................................35
1Chapter 11111IntroductionIntroduction 1The Alarm PanelThe Alarm Panel is used for sending distress alerts and showing visible and audible indication of incoming distress messages. Normally the Alarm Panel is installed at the conning position on the bridge.The distress buttons are protected by spring loaded covers to avoid unintended activation of a distress alert. The distress buttons must be pressed for 3 to 6 seconds before the distress alert is initiated.The Alarm Panel is supplied from 10.8 - 32 V DC. The input is protected against reverse polarity.Single or Multi Alarm PanelThere are two variants of the Alarm Panel: The SAILOR 6101A and the SAILOR 6103A. • The SAILOR 6101A Alarm Panel has one distress button and can send distress alerts and receive information on incoming distress messages via the Inmarsat C satellite system only. • The SAILOR 6103A Multi Alarm Panel has three distress buttons and can send distress alerts via Inmarsat C, and distress calls via VHF and MF/HF. It can also receive information on incoming distress messages.NoteIn Inmarsat C GMDSS systems it is mandatory to have two distress buttons. If you have a Mini-C GMDSS system, only one alarm panel is required, because the Message Terminal, which is part of the system, has a distress button.
Chapter 1: Introduction2The AlarmPanelSAILOR 6101A Alarm PanelThe SAILOR 6101A Alarm Panel is dedicated to Inmarsat C. It has one distress button for sending distress alerts over the Inmarsat C satellite network.The display shows distress alert transmission in progress and distress alerts received on the Inmarsat C network.Through the Ethernet connector you can interface to two Inmarsat C systems.NoteIf a distress alert is initiated on a system with duplicated units, only one of the units will send the alarm. The display shows a marker next to the name of the selected unit.
Chapter 1: IntroductionThe Alarm Panel 31111IntroductionSAILOR 6103A Multi Alarm PanelThe SIALOR 6103A Multi Alarm Panel connects to VHF equipment, MF/HF equipment and Inmarsat C equipment, and has a distress button for each type of system. The display shows distress messages received. It also indicates equipment type (VHF, MF/HF or Inmarsat C) when the equipment is detected by the Multi Alarm Panel.Through the Ethernet connector you can interface to two Inmarsat C systems, two VHF systems and two MF/HF systems.NoteIf a distress alert is initiated on a system with duplicated units, only one of the units will send the alarm. The display shows a marker next to the name of the selected unit.
Chapter 1: Introduction4The AlarmPanel
5Chapter 22222Using the Alarm PanelUsing the Alarm Panel 2This chapter provides a description of how to use the Alarm Panel. It has the following sections:•Starting up the Alarm Panel•Sending a Distress alert•Receiving Distress or Urgency messages•Displaying faults•General functions
Chapter 2: Using the Alarm Panel6 Starting up the Alarm PanelStarting up the Alarm PanelTo start up the Alarm Panel, do as follows:1. Switch on the Alarm Panel.Use the remote on/off switch, if installed. otherwise, the Alarm Panel is automatically powered with the system.2. The first column of the display shows which systems are connected to the Alarm Panel. A marker next to a system shows that it is the primary system for sending distress alerts or distress calls. In the example above, two VHF radios and one Inmarsat C system are connected to the Alarm Panel. VHF 1 and Inm-C 1 can be used for sending a distress call/alert.• On the SAILOR 6101A you can connect two Inmarsat C systems.• On the SAILOR 6103A you can connect two VHF systems, two Inmarsat C systems and two MF/HF systems.
Chapter 2: Using the Alarm PanelSending a Distress alert 72222Using the Alarm PanelSending a Distress alertTo send a Distress alert, do as follows:1. Open the cover for the Distress button you want to use (VHF, Inm C or MF/HF).2. Press and hold the button until the light is steady and the buzzer stops (approximately 5 seconds).For further details, see the user manual for the system you are using (VHF, Mini-C GMDSS or MF/HF). ImportantNever send a Distress alert if you are not in distress! Behavior MeaningButton light flashes, buzzer sounds.Marker in the display flashes with the button light.The Distress button is pressed. Hold until light and sound changes (approximately 5 seconds).Button light constant, buzzer is silentThe Distress alert is being sent(normally within 10 to 30 seconds)Button light shortly off every 15 secondsIn Inmarsat C systems: The Distress alert is confirmed
Chapter 2: Using the Alarm Panel8 Receiving Distress or Urgency messagesReceiving Distress or Urgency messagesWhen a Distress or Urgency message is received, the display of the Alarm Panel shows a flashing Distress text and the buzzer sounds periodically. The Distress text is shown next to the system on which the message was received.Check the connected system to see the contents of the message. In the example above check the Message Terminal in your Inmarsat C system to see the message.
Chapter 2: Using the Alarm PanelDisplaying faults 92222Using the Alarm PanelDisplaying faults The display of the Alarm Panel can show faults in the connected VHF, Inmarsat C or MF/HF equipment. Check the connected equipment for the cause of the fault. In the example above, you should check MF/HF radio number 1.NoteIf the defective system is configured to be the primary system for sending distress, the other system of the same type (if any) is automatically selected in stead. In the example above, MF/HF 2 is automatically selected because MF/HF 1 is defective.
Chapter 2: Using the Alarm Panel10 General functionsGeneral functionsButtons in front panelApart from the Distress button(s) described in Sending a Distress alert on page 7, the front panel has four other buttons: Test, Mute, and .Testing the Alarm PanelTo test the light and sound indicators in the Alarm Panel, do as follows:1. Press and hold the Test button.Verify that all light indicators and alarm buttons are flashing.2. While holding the Test button, press any other button, including the Distress button.The buzzer sounds to indicate that the pressed button and the buzzer is working.Muting the alarm soundTo mute the alarm sound while it is on, press the Mute button.NoteThis test only verifies the function of the Alarm Panel itself, not of any connected equipment or the total system. For information on how to test the system, refer to the manual for the individual system (Inmarsat C, VHF or MF/HF).NoteAlarm sounds are muted on all connected units until they are activated by a new event.
Chapter 2: Using the Alarm PanelGeneral functions 112222Using the Alarm PanelAdjusting the lightTo increase the light intensity, press and hold the button. To decrease the light intensity, press and hold the button. NoteThe light always goes to full intensity if there is an event such as a Distress message, a fault or the Test button is pressed.You can always use the Dim buttons to dim the light again if you want to.
Chapter 2: Using the Alarm Panel12 General functions
13Chapter 11111Installing the Alarm PanelInstalling the Alarm Panel 1This chapter provides a description of how to unpack, store and install the Alarm Panel. It contains the following sections:•Initial inspection•Storage•To install the Alarm PanelFor information on cable connections, see Connecting cables on page 21.
Chapter 1: Installing the Alarm Panel14 Initial inspectionInitial inspectionInspect the shipping carton immediately upon receipt for evidence of mishandling during transport. If the shipping carton is severely damaged or water stained, request that the carrier's agent be present when opening the carton. Save the carton packing material for future use.Check that the contents of the shipment are according to the enclosed packing list. If the contents are incomplete, if there is mechanical damage or defect, or if the Alarm Panel does not work properly, notify your dealer.After unpacking the Alarm Panel, inspect it thoroughly for damage and loose components or fittings.StorageThe Alarm Panel may be stored or shipped in temperatures between -40° C and +80° C. Protect the Alarm Panel from extreme temperature variation which can cause condensation. We recommend that you unpack the Alarm Panel immediately on delivery.Warning! To avoid electrical shock, do not apply power to the Alarm Panel if there is any sign of shipping damage to any part of the front or rear panel or the outer cover. Read the safety summary at the front of this manual before installing or operating the Alarm Panel.
Chapter 1: Installing the Alarm PanelTo install the Alarm Panel 151111Installing the Alarm PanelTo install the Alarm PanelGeneral installation requirementsNormally the Alarm Panel is installed at the conning position on the bridge. You can mount the Alarm Panel as a flush-mounted unit integrated in a console, on a desktop or in an overhead position.Make sure the Compass Safe Distance is maintained. See General specifications on page 31.Mounting the Alarm PanelThe next pages describe how to mount the Alarm Panel on a desktop, in an overhead position and flush mounted in a console.NoteThe mounting procedure is the same for the Alarm Panel and the Multi Alarm Panel so the descriptions in this chapter cover both types of Alarm Panel.
Chapter 1: Installing the Alarm Panel16 To install the Alarm PanelDesktop mountingYou can mount the Alarm Panel on a desktop using the mounting bracket. For details on how to mount the Alarm Panel, see Mounting the Alarm Panel with the mounting bracket on page 18.
Chapter 1: Installing the Alarm PanelTo install the Alarm Panel 171111Installing the Alarm PanelOverhead mountingYou can mount the Alarm Panel in an overhead position using the mounting bracket. For details on how to mount the Alarm Panel, see Mounting the Alarm Panel with the mounting bracket on page 18.
Chapter 1: Installing the Alarm Panel18 To install the Alarm PanelMounting the Alarm Panel with the mounting bracketTo mount the Alarm Panel using the mounting bracket, do as follows:1. Find a suitable location to mount the Alarm Panel. Make sure there is minimum 80 mm of free space for cable access behind the Alarm Panel.2. Use the four holes to fasten the mounting bracket to the mounting surface. Screws are included with the mounting bracket.3. Place the Alarm Panel in the mounting bracket.4. Mount the two knobs on the sides of the bracket, but do not tighten them yet.5. Connect the cables as described in Connecting cables on page 21.6. Adjust the angle of the Alarm Panel to the wanted position. The bracket can be adjusted ± 20°.7. Tighten the two knobs on the sides of the bracket when the Alarm Panel is in the correct position.
Chapter 1: Installing the Alarm PanelTo install the Alarm Panel 191111Installing the Alarm PanelFlush mountYou can mount the Alarm Panel in a flat surface, e.g. in a console, using the Flush mount bracket and screws included with the Alarm Panel.To mount the Alarm Panel in a console, do as follows:1. Find a suitable location in the console. Check that there is enough space for the Alarm Panel and an additional 80 mm space for cable entry.2. Cut a hole of 89 mm x 108 mm for the Alarm Panel.ImportantThe scale in the below drawing is not 1:1! Do not use it as a template without checking the dimensions.
Chapter 1: Installing the Alarm Panel20 To install the Alarm Panel3. Place the 4 square nuts in the cut-outs on the sides of the Alarm Panel, two on each side.4. Ensure that the flush mount gasket is placed correctly on the Alarm Panel.5. Fit the Alarm Panel into the cut-out in the console.6. Mount the flush mount bracket on the back of the Alarm Panel by mounting the 4 Torx screws through the bracket and into the square nuts placed in the Alarm Panel.7. Fasten the 4 Torx scre ws .8. Connect the cables as described in Connecting cables on page 21.
21Chapter 22222Connecting cablesConnecting cables 2This chapter provides a description of all connectors on the Alarm Panel and gives guidelines to cabling. It has the following sections:•Connectors•Cable requirements•Connecting the Alarm Panel•Connecting multiple Alarm Panels
Chapter 2: Connecting cables22 ConnectorsConnectorsOverviewThe drawing below shows the connectors on the Alarm Panel.PowerEthernet
Chapter 2: Connecting cablesConnectors 232222Connecting cablesLAN interfaceOverviewThere is one Ethernet (10/100 MB) connector on the rear panel of the Alarm Panel, used for communicating with connected equipment, such as a Message Terminal, VHF and MF/HF equipment. The interface supports PoE (Power over Ethernet), which means the Alarm Panel can be powered from a PoE device through the Ethernet.Pin-outThe figure and table below show the connector outline and pin assignments.ImportantOnly connect to units that are part of the system. For safety and compliance reasons, the Ethernet interface is restricted to internal communication in an isolated system.Pin functionPin number 10/100 DC on spares10/100 mixed DC & data1Rx+ Rx+DC+ (PoE)2Rx- Rx-DC+ (PoE)3Tx+ Tx+DC- (PoE)4 DC+ (PoE) unused5 DC+ (PoE) unused6Tx-Tx-DC- (PoE)7 DC- (PoE) unused8 DC- (PoE) unusedRJ-45 female
Chapter 2: Connecting cables24 ConnectorsDC Power inputOverviewThe DC Power input connects to a DC supply with 24 V DC nominal (10.8 to 32 V DC). The interface also has a “remote on/off” function.The Power connector is a custom connector; a matching cable with connector is included in the delivery.Pin-outThe figure and table below show the connector outline on the Alarm Panel, pin assignments and wire color in the power cable delivered with the Alarm Panel.Remote on/off (ON_IN)With the Remote on/off function you can switch the Alarm Panel on and off from a remote location, using a switch. Note that the Alarm Panel does not have a power button, so it is always on, unless you use the remote on/off function.ImportantIf you are not going to use the remote on/off function, you must connect pin 3 (ON_IN) to pin 2 (DC-) permanently. Pin number Pin function Wire color in power cable1 DC+ (10.8 - 32 V DC) Red2DC- (0 V DC) Black3ON_IN (see below)White4Not connected BlueFront view on Alarm PanelPanel lock, 4 pin male
Chapter 2: Connecting cablesConnectors 252222Connecting cablesTo use the Remote on/off function in the Alarm Panel, do as follows:1. Connect a switch to the white wire in the power cable (pin 3, ON_IN, in the Power connector.)2. Connect the other side of the switch to the black wire in the power cable (DC- (0 V DC) in the Power connector), so that pin 3 in the Power connector is connected to DC- (with a resistance less than 10 k when the switch is closed. • Switch closed: Alarm Panel is on• Switch open: Alarm Panel is off
Chapter 2: Connecting cables26 Cable requirementsCable requirementsBefore using the Alarm Panel for the first time, check that all cables are correctly wired and fastened.GroundingAll cables attached to the Alarm Panel must be shielded. • The shield of the Ethernet cable must be connected to ship ground in the Ethernet switch.• The shield of the power cable must be connected to ship ground at the power supply.Cable requirementsThe power cable supplied with your system is 2.5 m long with AWG 16 wires and a custom connector at one end. If you are going to use another cable or extend the supplied cable, make sure the cables are dimensioned correctly. When the cable is connected to the power supply, there must be minimum 10.8 V at the end of the cable.The Ethernet cable must be Cat. 5E or higher. Max. length is 100 m.
Chapter 2: Connecting cablesConnecting the Alarm Panel 272222Connecting cablesConnecting the Alarm PanelThis section covers both versions of the Alarm Panel, SAILOR 6101A and SAILOR 6103A.To connect the Alarm Panel, do as follows:1. Connect the power cable according to the description in DC Power input on page 24. 2. Connect an Ethernet cable to the LAN connector on the Alarm Panel.3. Attach the cables with cable straps as shown below.4. Connect the other end of the Ethernet cable to an Ethernet switch or alternatively a PoE switch.NoteIf you are using PoE as your power source for the Alarm Panel, the DC cable is optional.
Chapter 2: Connecting cables28 Connecting multiple Alarm Panels5. Connect the Ethernet interfaces on your Message Terminal, VHF radio and/or your MF/HF radio to the same switch, or a switch in the same network.When connected and powered, all the units are automatically set up to communicate with each other in the Ethernet network.Connecting multiple Alarm PanelsYou can connect up to twelve Alarm Panels on the same subnet (e.g. six SAILOR 6101A and six SAILOR 6103A).To connect multiple Alarm Panels, do as follows:1. Connect the Alarm Panels to an Ethernet switch.2. Connect the Ethernet switch to the system(s) used for transmitting the alarms, e.g. the Message Terminal in a Mini-C system or a VHF radio.The units are automatically set up to communicate with each other in the Ethernet network.ImportantOnly connect units that are part of the system. For safety and compliance reasons, the Ethernet interface is restricted to internal communication in an isolated system.
29Chapter 33333Service and repairService and repair 3This chapter describes what to do with defective units, including how to pack them for shipment if they are to be returned.IntroductionThe Alarm Panel designed to operate without preventive routine maintenance.Although the Alarm Panel is designed and built very service friendly, we strongly recommend that any acting service technician is trained specifically on the product. Repair or repair attempts performed by unqualified personnel may limit the warranty. The warranty on the system is defined and outlined by the distributor that supplied the system.We do not recommend repairing the Alarm Panel on board the ship. Replace the defective unit and have it repaired at a qualified workshop on shore.For further information on warranty and service, you may also use the Thrane & Thrane home page at http://www.thrane.com.
Chapter 3: Service and repair30 Repacking for shipmentRepacking for shipmentThe shipping carton has been carefully designed to protect the Alarm Panel and its accessories during shipment. This carton and its associated packing material should be used when repacking for shipment. Attach a tag indicating the type of service required, return address, model number and full serial number. Mark the carton FRAGILE to ensure careful handling.If the original shipping carton is not available, the following general instructions should be used for repacking with commercially available material.1. Wrap the Alarm Panel in heavy paper or plastic. Attach a tag indicating the type of service required, return address, model number and full serial number.2. Use a strong shipping container, e.g. a double walled carton of 160 kg test material.3. Protect the front- and rear panel with cardboard and insert a 7 cm to 10 cm layer of shock-absorbing material between all surfaces of the equipment and the sides of the container.4. Seal the shipping container securely.5. Mark the shipping container FRAGILE to ensure careful handling.
31Appendix AAAAASpecificationsSpecifications AGeneral specificationsItem SpecificationsMounting methodFlush mount or bracketPower 10.8 to 32 V DC, with “remote on/off” inputPower ConsumptionTypical 1 W, Maximum 3 WInterfaces Ethernet (10/100 Mbit), RJ45 connectorDC input, custom panel lock connectorCompliance • IEC 60945 • Wheelmark approved.IP protection IP30Ambient Temperature-15°C to 55°CStorage temperature-40°C to 80°CRelative humidity+40°C 93% 1 cycle
Appendix A: Specifications32 General specificationsVibration Vibration Sweep:2 Hz - 13,2 Hz at ± 1 mm13,2 Hz - 100 Hz at 7m/s2 2 h dwell at each resonance, otherwise 2 h at 30Hz in all three axesCompass safe distance1mDimensions H x W x DWithout bracket: 107 mm x 121 mm x 55 mmWith bracket: 124 mm x 153 mm x 90 mmWeight Without bracket: 302 g Item Specifications
33GlossaryBBBBGlossaryGlossary BAAWG American Wire Gauge. A means of specifying wire diameters. DDC Direct Current GGMDSS Global Maritime Distress Safety System. The system is intended to perform the following functions: alerting (including position determination of the unit in distress), search and rescue coordination, locating (homing), maritime safety information broadcasts, general communications, and bridge-to-bridge communications. HHF High Frequency. Radio frequencies between 3 and 30 MHz. Used for direct, long-distance (often inter-continental) communications. IIMSO International Maritime Satellite Organisation. An intergovernmental body established to ensure that Inmarsat continues to meet its public service obligations. Inmarsat C A service provided by Inmarsat, offering two-way, store-and-forward packet data communications via a small, low-cost terminal. Handles operational and personal messages, including e-mail, telex and fax, as well as distress and safety communications.
Glossary34IP Ingress Protection. An international classification system for the sealing effectiveness of enclosures of electrical equipment against the intrusion into the equipment of foreign bodies (i.e. tools, dust, fingers) and moisture. This classification system uses the letters "IP" followed by two or three digits. An "x" is used for one of the digits if there is only one class of protection; e.g. IPX4 which addresses moisture resistance only. MMF Medium Frequency. Radio frequencies (RF) in the range of 300 kHz to 3 MHz. Navtex, which is part of the current Global Maritime Distress Safety System occupies 518 kHz and 490 kHz for important digital text broadcasts. PPoE Power over Ethernet. A standard for combining power supply with transmission of data over the Ethernet. The source unit "injects" power into the Ethernet cable and the power is "picked up" at the connected device. RRx Receive TTx Transmit VVHF Very High Frequency. The radio frequency range from 30 MHz to 300 MHz. Ideal for short-distance terrestrial communication.
35IndexCCCCIndexIndex CAAlarm Paneldescription, 2Multi, 3types of, 1Ccable requirements, 26connectorsDC power input, 24LAN, 23overview, 22DDC power input connector, 24desktop mounting, 16dim function, 11dimensions, 32distresssending alert, 7distress message indication, 8document numberthis manual, iEEthernet connector, 23Ffaultsindication in display, 9flush mount, 19Iindicationfaults in connected equipment, 9incoming messages, 8initial inspection, 14Inmarsat C Alarm Panel, 2installation, 15LLAN connector, 23lightadjusting, 11Mmanualdocument number, imessage received indication, 8mountingflush mount, 19on desktop, 16Multi Alarm Panel description, 3muting alarm sound, 10Ppower input connector, 24Rreceiving distress or urgency messages,8repacking for shipment, 30repair, 29
Index36returning units, 30Ssafety summary, iiiSAILOR 6101A description, 2SAILOR 6103A description, 3service, 29specifications, 31storage, 14Ttest of Alarm Panel, 10types of Alarm Panel, 1Uunpacking, 14urgency message indication, 8

Navigation menu