Top Victory Electronics CM991H 19" Color Monitor User Manual 41A591 624 2A E

Download:
Mirror Download [FCC.gov]
Document ID	228155
Application ID	wEXXQ7XUkll04ay345XW1g==
Document Description	users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	39.98kB (499713 bits)
Date Submitted	2002-02-27 00:00:00
Date Available	2002-02-27 00:00:00
Creation Date	2002-02-22 16:16:44
Producing Software	Acrobat PDFWriter 4.05 for Windows NT
Document Lastmod	0000-00-00 00:00:00
Document Title	41A591-624-2A_E_.PDF
Document Creator	Microsoft Word - 41A591-624-2A(E)
Document Author:	yemmy

Before operating the monitor please read this manual thoroughly. This
manual should be retained for future reference.
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE
1. The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
2. Shielded interface cables and AC power cord, if any, must be used in
order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modification to this equipment. It is the
responsibilities of the user to correct such interference.
As an ENERGY STAR Partner our company has determined that this
product meets the ENERGY STAR guidelines for energy efficiency.
WARNING :
To prevent fire or shock hazard, do not expose the monitor to rain or moisture.
Dangerously high voltages are present inside the monitor. Do not open the
cabinet. Refer servicing to qualified personnel only.
Contents
Packing list ------------------------------------------------
Precautions ------------------------------------------------
Installation Instructions ----------------------------------Swivel Base ---------------------------------------------Power cord ---------------------------------------------Video cable ----------------------------------------------
Operating Instructions -----------------------------------General Instructions -----------------------------------Front panel control -------------------------------------How to adjust a setting --------------------------------Adjusting the picture ------------------------------------
Plug and play --------------------------------------------
10
Technical Support (FAQ) ----------------------------------
11
Appendix A – Specifications ------------------------------ 12-13
14
Appendix B – Factory Preset Timing Table -------------PACKING LIST
The product package should include the following items:
1. Pure Flat Color Monitor
2. Owner's Manual
3. Power Cord
4. Swivel Base
PRECAUTIONS
l Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen
sink, laundry tub, swimming pool or in a wet basement.
l Do not place the monitor on an unstable cart, stand, or table. If the
monitor falls, it can injure a person and cause serious damage to the
appliance. Use only a cart or stand recommended by the manufacturer or
sold with the monitor. If you mount the monitor on a wall or shelf, use a
mounting kit approved by the manufacturer and follow the kit instructions.
l Slots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to protect it
from overheating, be sure these openings are not blocked or covered. Do
not place the monitor on a bed, sofa, rug, or similar surface. Do not place
the monitor near or over a radiator or heat register. Do not place the
monitor in a bookcase or cabinet unless proper ventilation is provided.
l The monitor should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supplied to
your home, consult your dealer or local power company.
l The monitor is equipped with a three-pronged grounded plug, a plug with
a third (grounding) pin. This plug will fit only into a grounded power
outlet as a safety feature. If your outlet does not accommodate the threewire plug, have an electrician install the correct outlet, or use an adapter
to ground the appliance safely. Do not defeat the safety purpose of the
grounded plug.
l Unplug the unit during a lightning storm or when it will not be used for
long periods of time. This will protect the monitor from damage due to
power surges.
l Do not overload power strips and extension cords. Overloading can result
in fire or electric shock.
l Never push any object into the slot on the monitor cabinet. It could short
circuit parts causing a fire or electric shock. Never spill liquids on the
monitor.
l Do not attempt to service the monitor yourself; opening or removing
covers can expose you to dangerous voltages and other hazards. Please
refer all servicing to qualified service personnel.
l To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked
between 100 - 240 VAC, Min. 2.5A.
l The wall socket shall be installed near the equipment and shall be easily
accessible.
INSTALLATION INSTRUCTIONS
Swivel Base
To attach the swivel base to the monitor, do the following:
? Carefully turn the monitor on its side or upside down. ( see figure 1 )
? Locate the cavities at the bottom front of the monitor.
? Insert the pegs on the swivel base into these cavities. Push the swivel base
forward until the swivel base locks in place.
? To remove the swivel base, hold the bottom of the swivel base, then push
it out.
Install
Remove
Figure 1
Installing and Removing the Swivel Base
Power Cord
Power Source:
1. Make sure the power cord is the correct type that required in your area.
2. This monitor has a universal power supply that allows operation in either
100/120V AC or 220/240V AC voltage area ( No user adjustment is
required. )
3. Connect the power cord into your monitor’s power input socket, and then
plug the other end into a 3-pin AC power outlet. The power cord may
be connected to either a wall power outlet or the power outlet socket on
your PC, depending on the type of power cord supplied with your
monitor.
Video cable
Connecting the Video Cable: The monitor comes with a built-in video cable.
Plug the signal cable's 15-pin connector into the computer's video port and
tighten the two screws on the cable connector.
Caution: Don’t bend the signal cable, otherwise it will break the inner wire.
Connecting the Power Cord: Plug the power cord into the monitor's AC
power socket. Then plug the power cord into a grounded AC outlet or ULapproved power strip or the power output socket on your PC.
Caution: If the AC outlet is not grounded, install the proper grounding
adapter (not supplied).
Figure 2
1.
Power Cord
Connecting Cables
2.
Signal Cable
OPERATING INSTRUCTIONS
General Instructions
The other control knobs are located at the base of the monitor (See Figure 3).
By changing these settings, the picture can be adjusted to your personal
preferences.
? The power cord should be connected.
? Connect the video cable from the monitor to the video card.
? To turn the monitor on, press the POWER switch to ON position. The
power indicator will light up.
? Your monitor features a unique quick switch system which provides a
picture within seconds after the monitor is switched on.
EXIT
Figure 3
MENU
External Control Knob
EXTERNAL CONTROLS
1.
2.
3.
4.
5.
6.
POWER
POWER INDICATOR
MENU
CONTRAST/
BRIGHTNESS/
EXIT
Notes
? Do not install the monitor in a location near heat sources such as radiators
or air ducts , or in a place subject to direct sunlight , or excessive dust or
mechanical vibration or shock.
? Save the original shipping carton and packing materials, as they will come
in handy if you ever have to ship your monitor.
? For maximum protection, repackage your monitor as it was originally
packed at the factory.
? To keep the monitor looking new, periodically clean it with a soft cloth.
Stubborn stains may be removed with a cloth lightly dampened with a
mild detergent solution. Never use strong solvents such as thinner,
benzene, or abrasive cleaners, since these will damage the cabinet. As a
safety precaution, always unplug the monitor before cleaning it.
Front Panel Control
: Press this knob to switch ON/OFF of monitor’s power.
? MENU : Active OSD menu or function adjust confirm.
/ : Adjust contrast or function adjust.
/ : Adjust brightness or function adjust.
? EXIT : Exit a function or inactive OSD menu.
? Power Indicator :
Green —
Power On mode.
Orange —
Off mode.
How to adjust a setting
The monitor controls are accessed by pressing button MENU to enable OSD
(On-Screen-Display). The main menu will be displayed as follows.
H: 68.8KHz
V: 85Hz
Contrast
70
6500
9300
Figure 4
The OSD Message
Note: If adjustment or selection of any OSD menu is not made for more than
10 seconds, the current setup will be saved and the OSD will disappear
automatically.
Adjusting the picture
The description for functional control icons
1. CONTRAST
Adjust the picture contrast.
2. BRIGHTNESS
3.
Adjust the picture brightness.
H-CENTER
5.
Adjust the horizontal position of the picture.
H-SIZE
Adjust the picture’s horizontal size.
V-CENTER
6.
Adjust the vertical position of the picture.
V-SIZE
7.
Adjust the picture’s vertical size.
ZOOM
8.
Adjust the picture’s horizontal and vertical size simultaneously.
PINCUSHION
9.
Adjust the pincushion and barrel .
TRAPEZOID
4.
Adjust the picture’s trapezoid distortion.
10. PIN-BALANCE
Adjust to compensate the pincushion unbalance.
11. PARALLELOGRAM
Adjust the picture to be a rectangle.
12. ROTATION
Adjust the picture tilt to horizontal position.
13. 6500°K/9300°K ( COLOR TEMPERATURE )
The color temperature for 6500°K is x=0.313, y=0.329 and 9300°K
is x=0.283, y=0.297. It presents two different color sets on the screen.
You can select 9300°K or 6500°K by pressing MENU Key.
14. USER COLOR ( Red / Blue )
If the 9300°K normal white or 6500°K warmer white do not satisfy
your desire, properly adjust R . B GAIN controls to obtain your
optimum whiteness level.
15. DEGAUSS
If color impurity occurs when moving or swiveling the monitor,
press MENU Key and degauss to fix the picture condition.
16. MOIRE REDUCE
Moire is the result of interference between the phosphor layout and
the video signal. In some cases, you may find the moire very
noticeable. Press the MENU to enter in the moire reduce setting.
Please adjust the level to the optimum condition. Note: Too high of a
setting will cause the picture to shake.
17. RECALL
Press RECALL to restore the monitor to factory settings.
18. EXIT
Close OSD window.
19. SELECT LANGUAGE
Select the language as you like.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF
THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS
MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO
INPUT SIGNAL.
This monitor meets the Green Monitor standards as set by the Video
Electronics Standards Association (VESA) and/or the United States
Environmental Protection Agency (EPA) and The Swedish Confederation
Employees ( NUTEK ). This feature is designed to conserve electrical energy
by reducing power consumption when there is no video input signal present.
When there is no video input signal this monitor, following a time-out period,
will automatically switch to an OFF mode. This reduces the monitor's internal
power supply consumption. After the video input signal is restored, full power
is restored and the display is automatically redrawn. The appearance is similar
to a "Screen Saver" feature except the display is completely off. The display
is restored by pressing a key on the keyboard, or clicking the mouse.
Plug and play
Plug & Play DDC1/2B Feature
This monitor is equipped with VESA DDC1/2B capabilities according to the
VESA DDC STANDARD. It allows the monitor to inform the host system of
its identity and, depending on the level of DDC used, communicate additional
information about its display capabilities. The communication channel is
defined in two levels, DDC1 and DDC2B.
The DDC1 is a unidirectional data channel from the display to the host that
continuously transmits EDID information. The DDC2B is a bidirectional data
channel based on the I²C protocol. The host can request EDID information
over the DDC2B channel.
Video Cable Pin Assignments:
1. Red
5. Ground
9. NC
2. Green
6. R-Ground
10. Ground
14. V- sync / * VCLK
3. Blue
7. G-Ground
11. Monitor Ground
15. DDC-Serial Clock
4. Ground
8. B-Ground
12. DDC-Serial Data
10
13. H-sync
* FOR DDC
TECHNICAL SUPPORT (FAQ)
Problem & Question
Power LED is not on
No Plug & Play
Picture is fuzzy
Picture bounces or a wave pattern
is present in the picture
The power LED is ON (orange)
but there’s no video or no picture.
Missing one of the primary colors
(RED, GREEN, or BLUE)
Possible Solution
*Check if the Power Switch is in the ON
position
*Power Cord should be connected
*Check if the PC system is Plug & Play
compatible
*Check if the Video Card is Plug & Play
compatible
*Check if the D-15 plug pin of Video
Cable is bent
*Make sure the Monitor Drivers are
installed
*Adjust the Contrast and Brightness
Controls.
*Move electrical devices that may cause
electrical interference.
*Computer Power Switch should be in the
ON position
*Computer Video Card should be snugly
seated in its slot
*Make sure monitor’s video cable is
properly connected to the computer.
*Inspect monitor’s video cable and make
sure none of the pins are bent.
*Make sure computer is operational by
hitting the CAPS LOCK key on the
keyboard while observing the CAPS
LOCK LED. The LED should either
turn ON or OFF after hitting the CAPS
LOCK key.
*Inspect the monitor’s video cable and
make sure that none of the pins are bent.
11
APPENDIX A - SPECIFICATIONS
CRT
Viewable Image Size
Display Color
Input Signal
? Video
? Sync.
Synchronization
? Horizontal
? Vertical
Max. Resolution
Video Dot Rate
Factory Preset Timings :
User mode Timings :
Misconvergence
? Center
? Corner
Power Source
Operating
Humidity
48.3cm(19"), 90° deflection, 29mm neck,
0.25mm dot pitch non-glare screen.
45.7cm (18"), diagonal
Unlimited colors
Analog input All timing that meets scanning
frequencies
? Analog R, G, B 0.7Vpp positive/75 ohm
? Horizontal sync. : Positive/Negative
? Vertical sync. : Positive/Negative
30kHz to 95kHz automatically
50Hz to 160Hz automatically
1600 × 1200
200MHz
20
0.3mm Max.
0.4mm Max.
Switching mode power supply
AC 100-240V, 50Hz/60Hz full range
0°C to 40°C ambient
10% to 85% relative, non-condensing
Weight
Dimensions
20.0kg(Net)
• Monitor
446(W) × 436(H) × 455(D)mm
Signal Cable
15 pin mini D-Sub
External Controls:
Switch
Power On/Off Switch
MENU Key
Contrast/ UP Key
Brightness/ Down Key
EXIT Key
12
Functions ( OSD )
? Contrast
? Brightness
? H-Center
? H-Size
? V-Center
? V-Size
? Zoom
? Pincushion
? Trapezoid
? Pin-Balance
? Parallelogram
? Rotation
? 6500°K
? User color
? 9300°K
? Degauss
? Moire Reduce
? Recall
? Exit
? Select language
Plug & Play
DDC1/2B
EPA ENERGY STAR® On Mode = 130W
Off Mode = 5W
Power consumption
130W Max.
Preset display area
346mm × 260 mm
Regulations
UL, CSA, TÜ V / GS, FCC, FDA,
MPR II
13
APPENDIX B – FACTORY PRESET TIMING TABLE
VGA
720 × 400
HORIZONTAL
FREQUENCY
31.5kHz
VGA
640 × 480
31.5kHz
60Hz
VESA/85
640 × 480
43.3kHz
85Hz
VESA/85
800 × 600
53.7kHz
85Hz
VESA/85
1024 × 768
68.7kHz
85Hz
VESA/85
1280 × 960
85.9kHz
85Hz
VESA/85
1280× 1024
91.1kHz
85Hz
VESA/75
1600× 1200
93.8kHz
75Hz
STANDARD RESOLUTION
14
VERTICAL
FREQUENCY
70Hz

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 14
Creator                         : Microsoft Word - 41A591-624-2A(E)
Create Date                     : 2002:02:22 16:16:44
Title                           : 41A591-624-2A_E_.PDF
Author                          : yemmy
Producer                        : Acrobat PDFWriter 4.05 for Windows NT

EXIF Metadata provided by EXIF.tools